DESCRIPTION TIPELIN 2100J is a high density unimodal polyethylene copolymer (with propene-1 as comonomer) intended for injection moulding of general purpose products. It offers good balance of properties between stiffness and processability. The grade contains antioxidant and acid scavenger. APPLICATIONS TIPELIN 2100J is recommended for making bottle closures (for not carbonated drinks), pails, crates, pallets, dust bins, large containers, lids (for pails, drums and containes). TIPELIN 2100J is suitable for food contact and for manufacturing of toys. The product complies with Food Contact, Pharmaceutical and Toy Safety Regulations. PROPERTIES Test method Unit Typical value Melt Mass-Flow Rate (MFR) (190 C /2.16 kg) ISO 1133-1 g/10 min 4.0 Density (23 C) * ISO 1183-2 kg/m 3 953 Tensile Strength at Yield ** ISO 527-3 MPa 23 Tensile Strain at Yield ** ISO 527-3 % 10 Tensile Strength at Break ** ISO 527-3 MPa 12 Tensile Strain at Break ** ISO 527-3 % 640 Flexural modulus** ISO 178 MPa 1100 Izod Impact Strength** ISO 180/A kj/m 2 7 Vicat Softening Temperature * ISO 306/A 120 C 124 Shore D Hardness ** ISO 868-60 ESCR (100 % Igepal, F 50)* ASTM D 1693 h 6 OIT (200 C) EN 728 min 45 Shrinkage (TD/MD)** ISO 294-4 % 2.5/1.9 Typical properties, not to be used as specification. * Average mechanical property values of several measurements carried out on standard pressed specimens (ISO 293) conditioned at room temperature (ISO 291). ** Average mechanical property values of several measurements carried out on standard injection-moulded test specimens prepared in accordance with ISO 294-1. PROCESSING TIPELIN 2100J can be used in conventional injection moulding machines. Recommended processing temperatures are 210-250 C.
2
3 STORAGE AND HANDLING Pellets are packed in 25 kg PE-LD bags and transported on stretch or shrink-wrapped pallets at eligible load of polymer 1375 kg. Heat treated pallets are available as well. We use adhesive between the bags in order to avoid their slipping. Pay attention to this fact during the removing of the bags from the pallets. The prefered method is to lift the bag at first without rotation. Transportation in a road silo or rail silo is also available. For more detailed information please contact SLOVNAFT and MOL Petrochemicals sales representative. Since polyethylene is a combustible substance, the fire safety rules applicable for combustible materials in warehouses and store rooms should be observed. If polymer is stored in conditions of high humidity and fluctuating temperatures, then atmospheric moisture can condense inside the packing. If it happened, it is recommended the pellets to be dried before use. During the storage polyethylene should not be exposed to UV radiation and temperatures above 40 C. Producer does not take responsibility for any damages caused by adverse storage. REACH STATEMENT Polymers are exempt of REACH registration. However, their raw materials which mean monomers and relevant additives have been registered. MOL Petrochemicals is committed to fully respect legislation and will only use REACH compliant raw materials. At this point in time TIPELIN does not contain any substances specifically identified as SVHC at levels greater than 0.1%. SAFETY See MSDS. RECYCLING Polyethylene resins are suitable for recycling using modern recycling methods. In-house production waste should be kept clean to facilitate direct recycling. DISCLAIMER The information provided in this publication has been compiled to the best of our present knowledge. However, in view of the various applications of polyethylene resins and the equipment used, the processing conditions may differ. The recommendations and data herein are to be construed as informational only and do not relieve users from carrying out their own tests and experiments prior to processing in order to check suitability for a specific use. It is the responsibility of those to whom we supply our products to ensure that any proprietary rights and existing laws and legislation are observed. Our products are under continuous development, therefore we reserve the right to change the information presented in this brochure at our own discretion. The REACH statement herein does not constitute legal advice. The REACH statement is provided for informational purpose only.
MANUFACTURER MOL Petrochemicals Co. Ltd. TECHNICAL SERVICE MOL Plc. Polymer Technical Service MOL +36 49 521 540 +36 49 522 607 Fax: +36 49 886 491 E-mail: pts@mol.hu SALES ORGANIZATION GERMANY Im Trutz Frankfurt 49, D-60322 Frankfurt am Main, Germany +49 69 154 04 0 Fax: +49 69 154 04 41 E-mail: polymersales@molgermany.de ITALY Via Teulié, 1, 20136 Milano, Italy +39 02 58 30 5523 Fax: +39 02 58 30 3492 E-mail: tvkitaly@it.tvk.eu POLAND Ul. Postępu 17D 02-676 Warszawa, Poland +48 22 545 70 70 Fax: +48 22 545 70 60 E-mail: petchem@slovnaft.pl AUSTRIA Walcherstrasse 11A, 7.Stock A- 1020 Wien, Austria +43 1 211 20 1120 Fax: +43 1 211 20 1198 E-mail: JHauk@molaustria.at FRANCE Paris, France Mobile Phone: + 33 7 89 86 10 64 + 33 1 64 32 44 17 E-mail: husson.iren@fr.tvk.eu ROMANIA Str. Danielopolu 4-6 ET1 Sector 1 Cod 014 134 Bucuresti, Romania +40 21 204 85 00 +40 21 204 85 02 Fax: +40 21 232 10 59 E-mail: petchem@molromania.ro
5 HUNGARY +36 49 521 355 Fax: +36 49 886 491 E-mail: polymersales@mol.hu UKRAINE 04655 Kiev Stepana Bandery ave., 23, 7th floor, of. 305, Ukraine +380 44 374 00 80 +380 67 463 58 69 Fax: +380 44 374 00 90 E-mail: JZavojko@mol-ukraine.com.ua SLOVAKIA AND CZECH REPUBLIC Vlčie hrdlo 1 824 12 Bratislava, Slovak Republic + 421 2 5859 7515 + 421 2 5859 7622 + 421 2 5859 7741 + 421 2 5859 7231 E-mail: polymersales@slovnaft.sk CROATIA, SLOVENIA, SERBIA, BOSNIA AND HERZEGOVINA, MONTENEGRO, ALBANIA, KOSOVO Savska cesta 41/XIII HR-10000 Zagreb, Croatia +385 1 6160 600 Fax: +385 1 6160 601 E-mail: polymersales@tifon.hr OTHER EUROPEAN COUNTRIES +36 49 521 355 +36 70 458 4563 +36 70 373 9209 Fax: + 36 49 886 491 E-mail: polymersales@mol.hu June, 2017