New Holland 0-90 0A - 90A Buhler Genesis 1/10/10/ Tractors MANUAL 191
New Holland 0-90 0A - 90A Buhler Genesis 1/10/10/ Tractors Blade, pivot frame 1 Hydraulics Tractor fit-up, mounting Operation, maintenance 9 Attachments Safety, warranty 1 Industrial Drive, Box 0 Regina, Sask. Canada SP B1 0 - -10 fx degelman@degelman.com www.degelman.com SAFETY The safety instructions that follow pertain only to this specific equipment. You should be aware of agricultural industrial safety especially related to heavy equipment. If you are not familiar with safety procedures then you should get training. Improper use will result in maiming or death. 191
Buhler Genesis 1-191 9 1 1 1 1 1 p1
191 Qty 1 0 1ft / Dlock blade 1 00 1ft 1 00 ft 1 001 9ft 1 01 Angling cap 1 9 Bolt / x 1/ Gr Lock nut / GrC 1 Relief valve brkt 1 0001 Depth shoe 0 Pin / x 1/ 901 Lynch pin /1 x 1 1/ 9 0 ft Cutting edge, 1ft bld 0 ft, 1ft bld ft, ft bld 1 09 9ft, ft bld 1 0 Plow bolt / x 1/ as Lock nut / unitorq required 1 0 00 Pivot frame 1 1 0 Wear bushing 1 p
Buhler Genesis 1- Hydraulics 11, 1/ x x 1 1/ Lift cylinder 191 1 1 11 Barrel 1 1 Lock ring 1 1 Open cap 1 1 Lock nut / unf unitq 1 1 Piston 1 10 Rod clevis 1 90 Clevis pin 9 Shld bolt 1/ x 1 1/ 9 9 Flat washer.91 1 Seal kit 000 Lift hydraulic kit 9 19, x 1 x 1 1/ Angle cylinder 1 111 Barrel 1 1 Lock ring 1 1 Open cap 1 1 1 Lock nut / unf unitq 1 1 Piston 1 1099 Rod clevis 1 90 Clevis pin 9 Shld bolt 1/ x 1 1/ 9 9 Flat washer.91 1 Seal kit 00 Angle hydraulic kit 9 p
1 Relief valve 1 Bolt /1 x 1/ Qty () (0) Relief (0) () Flat washer /1 0 Lock washer /1 (1) (1) Nut /1 Angle Lift (9) (9) Lift Angle 1 (1) (1) Install behind brkt (0) (0) (1) continued (1) continued (0) hose length in inches 1 Hose / x (9) 11 Hose / x (1) 0 01 1 0 EL / m JIC x ORB 1 01 TEE / m JIC 1 Connector / m JIC x ORB TEE / m JIC x JIC x ORB 1 Quick coupler 19 Hose / x (0) 1 Hose / x () mxf 1 Hose / x () 1 Hose / x (0) 1 Hose / x (1) 1 1091 Coloured hose markers, 1 pack () mxf () mxf Hose take-up Use different coloured tape to mark sets of hydraulic hoses. Use one or two tapes to indicate lifting or retracting hoses. () mxf () mxf 191 p
Fit up Buhler Genesis 1-1 9 1 Buhler 191 Buhler 1 1 1 1 9 1 1 1 0 19 1 1 Back of back bolt bar- Upper row of holes Buhler Front of back bolt bar All tractors Rear frame 1st nd rd th p Main frame th th th 1th
Existing NH nut used on back, Super steer (illustrated): Take weight brkt off axle install hardware shown Hook hose take up to tractor frame Tractor's hyd ports at rear Tractor axle Existing NH spacer used on front,,, 9 Back plate of front bracket Qty 1 000 Main frame 1 00 Front hanger 1, Buhler 0 Front hanger 1 0 Bolt / x 1/ Lock nut /,,,, This front plate hardware is only used to install the NH weight brkt on regular steer tractors. Front view, looking back 1 1,,, Front brkt front plate; Top view top row of holes NH weight brkt Spacer () only needed if you're using weights 00 Front bracket 1 Bolt M0 x 0 1 Lock washer M0 99 Front brkt spacer 9 1 Bolt M0 x 0 9 Flat washer M0 0 Lock nut M0 1 Bolt M0 x 0 1 00 RH side bracket 1 01 LH 1 1, Buler 0 RH side brkt 1 0 LH 1 Bolt M0 x 10 1 Flat washer M0 1 1 Lock nut M0 1 1 1 0 Rear frame 1 1 Bolt / x 1/ 1 1 09 Lock washer / 1 1 Nut / 1 Grand total Regular steer: Take NH weight brkt off frame, no changes made to axle. NH weight brkt can be reinstalled on front brkt. Suitcase weights must removed to install front brkt. Weights must be removed when blade is mounted. 19 00 Pivot pin, main-pivot 1 0 0 Bolt 1/ x 1/ 1 1 0 Lock washer 1/ 1 0 Nut 1/ 1 Bolt 1 x 1 gr 0 Spacer washer 91 Bolt 1 x 1 91 Weight brkt spacer 00 Hose take up 1 0 Spring 1 9 0 Wear bushing 1 191 p
191 Buhler Genesis 1- Rear frame 0 1 01 Dlock linkage c/w... 01 Wedge 1 1 Compression spring 1 01 DL linkage plate/bush 1 91 Roll pin 1 00 Bolt / x 0 DL bushing Lock nut / 9 00 Lock pin 09 UHMW plastic block 0 Hose clamp part c/w... 1 1 Bolt /1 x 1 1/ 1 1 09 Top plate 1 1 0 Clamp two halves 1 1 0 Bottom plate weld on 1 1 010 DL handle 1 1 9 9 1 1 1 1 1 p
Mounting Buhler Genesis 1- Dlock closing Take clip pin off Use the handle to close the latch Line tractor up over the rear/main frames. Make sure Dlock is open, clip pin is put back on and handle is stored. Drive forward so that the front bracket pin is just behind the front hanger's hook. It should be lined up so you can drive into the front hanger when it is raised up. Hook up the hydraulics. Note the second position for the final movement of closing Raise the front hanger by extending the lift cylinders so the pin and hook are level. Secure with clip pin Put handle away Drive forward until the pin is in the front hanger. Now close the lift cylinders. This will raise up the rear frame. Take off clip, close the Dlock, attach clip then store the handle. There should be a /" gap Note: the clip pin holds the Dlock both open closed Make sure DLOCK is closed properly To disengage: 1- RAISE THE BLADE - Open the Dlock - Extend lift cylinder to lower rear frame - Lower main frame to ground - Back out to clear front hanger - Unhook hydraulics WARNING It is vital to raise the blade before opening Dlock. p If you don't the rear frame will fall. 191
Operation, maintenance TORQUE Buhler Genesis 1-191 Before using for the first time Lube all points Torque all hardware to correct setting Check hardware torque hydraulics after the first hrs again after hrs Check steering stops tread width settings Before using each time Check: If all points lubricated All components attached securely Condition of cutting edge Depth shoe wear Hydraulics; Tractor s oil reservoir Condition of hoses, lines fittings Bleeding hyd Bleed hydraulics of air. Cycle the hydraulics several times and hold the cylinders at full extent for several seconds. Soft uneven ground Depth shoe low Blade high Depth shoes Rear end weights Tire inflation If needed balance out your tractor by ballasting the rear end. You may need to raise the tire pressure in the front wheels. Consult your tractor's manual. Floatation mode Here are some the things you can do with your hyd system in float position; Skim the top of pavement Run on the skid shoes Back drag Cold weather Cycle the cylinders several times to warm up system. Hard even ground Depth shoe high Blade low TORQUE SETTINGS Imperial Size Metric Size all hardware All hardware; Hex head, Plated, Gr. UNC (imperial) or P.9. (metric) Hoses; /, ends c/w / JIC female swivel Unless stated otherwise Grade 1/ 9 1 /1 1 / 0 /1 0 0 1/ 1 9/1 1 / 1 1 / 0 / 0 1 0 90 SAE..9 0. 1... 1 1 9 1 0 1 0 ft lb ft lb Hyd. fitting Size / ft lb p9 / 90
Record your serial number blade width 191 9,, 1 or 1ft? Lubrication All hardware; Hex head, Plated, Gr. UNC (imperial) or P.9 (metric) Hoses; /, ends c/w / JIC female swivel Unless stated otherwise? Metric thread specs M Thread pitch 1 1 0.. 0. Buhler Genesis 1- Lube all points and mechanisms after every hr of use. Lube both sides Lube with: Grease Angle cap Front brkt, top Spray lubricant Lift cyl Lift cyl Front brkt, bottom Angle cyl Angle cyl Pivot pin, pivot/main frm Dlock p
Options Decals reflectors 1 Warning decal, Falling Blade 100 Degelman logo / lg 10 Red reflector / 19 Amber reflector 1/ lg 1 Buhler Genesis 1-190 / blade decal 1 191 1 Bracket only used for blades without integrated brackets 1 1 9 19 1 Place washers on pin to fill gap 1 1 1 1 19 Top extension 1ft 1 1 1ft 1 1 ft 1 11 9ft 1 0 Bolt / x 9 1 Flat washer / Nut / Flat washer 1 1/ 9 1 1 Silage extension 1ft 1 1 1ft 1 ft 1 9ft 1 1 Bracket 0 Bolt / x 1/ 1 Flat washer / 1 09 Lock washer / Nut / 1 0 Extension 1ft 1 0 Bolt / x 1 09 Lock washer / 1 Nut / 1 01 Side plate 1 0 Bolt / x 1 09 Lock washer / 19 Nut / p
KILLED, INJURED OR SAFE? Safety YOUR CHOICE You are responsible for your own safety. If you are not familiar with basic agricultural industrial safety, you must get training. Owners of equipment must by law give operating instructions to other operators such as family members or a hired hand. Making any design changes to equipment could cause a hazard and damage your machine. Wear proper safety equipment. Have handy; First aid kit Fire extinguisher Before working on machine: Turn tractor off Set controls in neutral Remove ignition key Clean all reflectors and lights HYDRAULIC Keep all parts clean. Replace worn or damaged parts. Don t try any makeshift repairs. Before operating check that everything is tight and not broken. Wear gloves and eye protection when searching for leaks. Use a piece of wood or cardboard but not your hand. High pressure oil will penetrate your skin. If that happens you risk serious injury. BLADE Lower blade to the ground when not in use. Keep clear of blade when tractor is running. Keep hands feet away from under blade. Turn engine off when hooking up hydraulics and engaging DLOCK during mounting or dismounting. TRANSPORTING Lift blade up then hold with safety chain. Make sure SMV sign reflectors are clean. Use your hazard lights. 191 (090) WARRANTY Degelman Industries warrants this product to the original owner for a period of one (1) year parts and labour and two () years parts from the date of purchase. All matters related to the warranty of our products must be handled through the authorized selling dealer. Warranty does not cover normal wear of the machine components or damages caused by lack of maintenance or misuse, and is subject to the following provisions. REPLACEMENT PARTS: Will be warranted for a period of ninety (90) days. WARRANTY ON MACHINES USED FOR CUSTOM WORK, RENTALS OR INDUSTRIAL USE: Will be warranted as stated above, with the exception that it will be for a period of ninety (90) days only. TIRES: Will be adjusted for warranty by tire manufacturer. LABOUR: Any labour subject to warranty must be authorized by a Degelman representative before work is started. Warranty labour allowance and rates will be handled according to established warranty service policy. GOVERNMENT LEGISLATION: Warranty terms and conditions are subject to Provincial or State legislation. MODIFICATIONS: Warranty will be void if any component is altered or modified, unless written authorization is granted by Degelman Industries Limited. WARRANTY ON ATTACHED EQUIPMENT: No responsibility will be assumed for whatever damages may occur to persons, tractors or property. p1