ASME END SUCTION PUMPS Catalogue K-90

ASME END SUCTION PUMPS Catalogue K-90 ASME B3.1-01 ISO 9001:008 REGISTERED COMPANY Engineered Pumps for Industrial and Municipal Services

ASME B3.1 / ANSI END SUCTION PUMPS This catalogue provides the information you need to select a Smart Turner ASME B3.1 Pump to fit your specific needs. The ASME End Suction Pump range continues the Smart Turner tradition of providing well proven, uncomplicated designs incorporating high efficiency and smooth, low NPSH performance in a compact economical, Heavy Duty End Suction Pump. Smart Turner ASME Pumps are ideally suited to plant service and chemical process applications where continuous, reliable operation is essential, whether the fluid is clean, dirty, corrosive or abrasive. Smart Turner ASME Pumps are quality built for rugged, trouble free operation. They are available with either grease or oil lubricated bearings as standard. Smart Turner ASME Pumps are engineered to exceed ANSI standards in all essential features. Impeller adjustment is positive and uncomplicated. High shaft stiffness yields low shaft deflections. Oversize bearings provide more than year L10 life in all cases. The large stuffing box and the rear impeller pump out vanes provide excellent heat dissipation and low stuffing box pressure for long packing and seal life. The recessed pump out vane arrangement minimizes the effects of wear by maintaining pump out efficiency throughout the full range of impeller adjustment. Smart Turner ASME Pumps are produced and stocked in a wide range of sizes using only three bearing housings. This makes an efficient parts inventory possible through extensive interchangeability of parts between pumps. With the inclusion of ASME Pumps, Smart Turner can now offer a range of End Suction Pumps, totaling over 60 models, with capacities to 6000 USGPM, heads to 800 feet and speeds to 3500 Rpm. This catalogue features ASME Chemical Process Pumps. For other EndSuction models, see catalogues B-90, D-90, F-90 and G-90. SMART TURNER SOLUTION TO PUMPING PROBLEMS Whatever fluids you pump, Smart Turner has the background and technology to help you meet your needs effectively and efficiently with quality designed and built pumps. Smart Turner has established an enviable reputation for reliability while pumping chemicals, oil, beverages, slurries or sewage.almost any liquid known to man. For over 100 years, Smart Turner has been dealing with and solving pumping problems throughout the world. This in-depth experience, coupled with modern computer technology at every level from concept to shipping, is available to you through our sales and engineering personnel, coast to coast. At Smart Turner, pumps are our only business, designed through experience to provide consistent performance and minimum maintenance. A wide range of sizes and types allows us to match the right pump to your specific application. For further information, or an evaluation or your pumping system requirements, contact your nearest Smart Turner sales office or distributor as listed on the back cover of this catalogue.. CONSTRUCTION MATERIALS All Iron 316 Stainless Alloy 0 CD4MCuN Hastelloy C Bronze Monel Other Materials on Application

PAGE INDEX PAGE SPECIFICATION... K-.0 DIMENSIONS Bare Pump... K-3.0 Pump, Base and Motor... K-3.1 PARTS #1 Frame Grease Lube... K-4.0 #1 Frame Oil Lube... K-4.1 # / #3 Frame Grease Lube... K-4. # / #3 Frame Oil Lube... K-4.3 Seal Arrangements... K-4.4 Gland Arrangements... K-4.5 MATERIAL LIST... K-5.0 PUMP DATA... K-6.0 RANGE CHARTS... K-.0 PHOTOS... K-8.0 3.

K-.0 DESIGN AND CONSTRUCTION FEATURES: Pump: Back pullout construction to ASME B3.1 / ANSI dimensional standards. Top center line to discharge and casing feet ensure maximum rigidity and stability, while Smart Turner quality and precision ensure accurate fits and clearances. Casing: A radially split cast volute with integral suction cover, ruggedly designed with generous allowance for abrasion and corrosion. 150# ANSI flat faced flanged connections are standard. 300# flat faced flanges or RF are an option. Impeller: Cast in one piece, the fully open impeller is trimmed to the exact diameter required and is factory balanced. The heavy section of the impeller provides excellent wear and corrosion allowance and the partial rear shroud provides maximum support for the blades. Rear pump out vanes provide axial hydraulic balance and low, but normally positive, stuffing box pressure. The pump out vanes are recessed into the stuffing box cover to maintain pump out efficiency if axial adjustment is made. Stuffing Box Cover: A heavy one piece casting with rabbeted fit to the casing for positive alignment. The deep bore will accept a wide range of packing or mechanical seals. Optional Tapered and Big Bore stuffing boxing are available. Gland: Split for packed stuffing boxes and solid for mechanical seals, the gland can be provided in a variety of arrangements to suit the application. Gaskets: All gaskets are fully contained. Shaft: Precision machined high quality alloy, normally fitted with a renewable sleeve, and oversized to minimize deflection to ensure smooth operation and maximize packing or seal life. Hardened Shafts are available as an option. Sleeve: A precision machined, stainless steel, hook sleeve with an O- Ring seal against the impeller. A solid shaft without sleeve can be provided. Hardened Sleeves are available as an option. Bearings: Antifriction bearings are generously sized for longer life, with a double row thrust bearing for minimum end play. Grease or oil lubricated arrangements are available. Grease is recommended for most services as being simpler and more reliable. Bearings are protected by seals at both ends of the housing. Bearing Housing: A rigid casting with precisely machined bores and rabbet fit to the adaptor to ensure concentricity and alignment with the stuffing box cover, casing and rotating element. The smaller housing has an integral foot and integral adaptor. Adaptor: A rigid casting with integral gland drip reservoir, precision machined to ensure rigid and consistent alignment between bearing housing and liquid end. Interchangeability: All pumps utilize one of only three bearing housings. Pumps with the same bearing housing have fully interchangeable shafts, sleeves bearings, packing, seals, glands, and hardware resulting in an efficient parts inventory at both the factory and the customer. Tests: All pumps are hydrostatically tested to 50 PSI above the maximum casing design pressure. Performance Testing is available as an option OPTIONAL EQUIPMENT: Base: A rigid channel or fabricated base can be provided to our standard for electric motor drives. Special bases can be provided and can incorporate grout holes, drip rims and other features. Guard: A coupling guard to our standard can be mounted on the base plate. Special guards can be accommodated. Flexible Coupling: For normal duty our current standard is provided when a coupling is ordered. However, couplings of almost any style or manufacturer can be accommodated. Motors: An electric motor or other driver can be provided. Cooler: A cooling coil can be fitted to oil lubricated bearing housings for operation at elevated temperatures. No cooling is required for liquid temperatures below 350 F (1 C). Note; standard grease lubrication is good to liquid temperatures of at least 50 F (10 C). OTHER END SUCTION PUMPS Other Single Stage End Suction Pumps, End Suction design Two Stage Pumps, Non Clog Pumps, and Refuse Pumps are also available. 4.

DIMENSIONS ASME B3.1 / ANSI END SUCTION BARE PUMP K-3.0 PUMP FRAME # 150# ANSI FF PUMP DIMENSIONS MODEL SUCT DISCH CP D E1 E F H O U V X Y KEYWAY 1.5x1x6 1 1.5 1 1.5 5.5 3 0.5 0.65 11.5 0.85.15 6.5 4 3/16 x 3/3 3x1.5x6 1 3 1.5 1.5 5.5 3 0.5 0.65 11.5 0.85.15 6.5 4 3/16 x 3/3 1.5x1x8 1 1.5 1 1.5 5.5 3 0.5 0.65 11.5 0.85.15 6.5 4 3/16 x 3/3 3xx6 3 3.5 8.5 4.85 3.65 1.5 0.65 16.5 1.15.5 8.5 4 3x1.5x8 3 1.5 3.5 8.5 4.85 3.65 1.5 0.65 16.5 1.15.5 8.5 4 3xx8 3 3.5 8.5 4.85 3.65 1.5 0.65 1.5 1.15.5 9.5 4 4x3x8 4 3 3.5 8.5 4.85 3.65 1.5 0.65 19.5 1.15.5 11 4 x1x10 1 3.5 8.5 4.85 3.65 1.5 0.65 16.5 1.15.5 8.5 4 3x1.5x10 3 1.5 3.5 8.5 4.85 3.65 1.5 0.65 16.5 1.15.5 8.5 4 3xx10 3 3.5 8.5 4.85 3.65 1.5 0.65 1.5 1.15.5 9.5 4 4x3x10 4 3 3.5 8.5 4.85 3.65 1.5 0.65 19.5 1.15.5 11 4 3x1.5x13 3 1.5 3.5 10 4.85 3.65 1.5 0.65 0.5 1.15.5 10.5 4 3xx13 3 3.5 10 4.85 3.65 1.5 0.65 1.5 1.15.5 11.5 4 4x3x13 4 3 3.5 10 4.85 3.65 1.5 0.65.5 1.15.5 1.5 4 6x4x13 6 4 3.5 10 4.85 3.65 1.5 0.65 3.5 1.15.5 13.5 4 8x6x13 3 8 6 33.85 14.5 8 4.5 18.5 0.85 30.5.35 3.5 16 6 5/8 x 5/16 10x8x13 3 10 8 33.85 14.5 8 4.5 18.5 0.85 3.5.35 3.5 18 6 5/8 x 5/16 8x6x15 3 8 6 33.85 14.5 8 4.5 18.5 0.85 3.5.35 3.5 18 6 5/8 x 5/16 10x8x15 3 10 8 33.85 14.5 8 4.5 18.5 0.85 33.5.35 3.5 19 6 5/8 x 5/16 8x6x1 3 8 6 33.85 14.5 8 4.5 18.5 0.85 3.5.35 3.5 18 6 5/8 x 5/16 10x8x1 3 10 8 33.85 14.5 8 4.5 18.5 0.85 33.5.35 3.5 19 6 5/8 x 5/16 These are not certified dimensions. Certified drawing can be obtained on request. All dimensions in inches. 5.

DIMENSIONS ASME B3.1 / ANSI END SUCTION PUMP, BASE & MOTOR DIMENSIONS K-3.1 ANSI END SUCTION PUMP, BASE & MOTOR PAGE K-3.1 PUMP FRAME 15/150 # ANSI FF PUMP DIMENSIONS BASE PER MOTOR FRAME MOTOR DIMENSIONS MODEL # SUCT DISCH CP D X Y 56-184 13-15 54-56 84-86 34-365 404-405 444-449 1.5x1x6 1 1.5 1 1.5 5.5 6.5 4 1A A A 3x1.5x6 1 3 1.5 1.5 5.5 6.5 4 1A A A 1.5x1x8 1 1.5 1 1.5 5.5 6.5 4 1A A A 3xx6 3 3.5 8.5 8.5 4 3A 4A 5A 5A 6A 3x1.5x8 3 1.5 3.5 8.5 8.5 4 3A 4A 5A 5A 6A PUMP FRAME 15/150 # ANSI FF PUMP DIMENSIONS BASE PER MOTOR FRAME 3xx8 3 3.5 8.5 9.5 4 3A 4A 5A 5A 6A MODEL 4x3x8 # SUCT 4 DISCH 3 3.5 CP 8.5 D 11 X Y 4 56-184 3A 13-15 4A 54-56 5A 84-86 5A 34-365 6A 404-405 A 444-449 1.5x1x6 x1x10 1 1.5 1 1.5 3.5 5.5 8.5 8.5 6.5 4 3A 1A 4A A 5A A 5A 6A A 3x1.5x6 1 3 1.5 1.5 5.5 6.5 4 1A A A 3x1.5x10 3 1.5 3.5 8.5 8.5 3A 4A 5A 5A 6A A 1.5x1x8 1 1.5 1 1.5 5.5 6.5 4 1A A A 3xx10 3xx6 3 3.5 8.5 8.5 9.5 4 3A 4A 5A 5A 6A A 3x1.5x8 3 1.5 3.5 8.5 8.5 4 3A 4A 5A 5A 6A 4x3x10 4 3 3.5 8.5 11 3A 4A 5A 5A 6A A 3xx8 3 3.5 8.5 9.5 4 3A 4A 5A 5A 6A 6x4x10 4x3x8 46 34 3.5 8.5 10 1.5 11 4 3B 3A 4B 4A 5B 5A 5B 5A 6B 6A A 3x1.5x13 x1x10 3 1.5 1 3.5 8.5 10 10.5 8.5 4 3B 3A 4B 4A 5B 5A 5B 5A 6B 6A A A 3x1.5x10 3 1.5 3.5 8.5 8.5 4 3A 4A 5A 5A 6A A 3xx13 10 11.5 3B 4B 5B 5B 6B A 3xx10 3 3.5 8.5 9.5 4 3A 4A 5A 5A 6A A 4x3x10 4x3x13 4 3 3.5 8.5 3.5 10 1.5 11 4 3B 3A 4B 4A 5B 5A 5B 5A 6B 6A A 3x1.5x13 3 1.5 3.5 10 10.5 4 3B 4B 5B 5B 6B A 6x4x13 6 4 10 13.5 3B 4B 5B 5B 6B A 3xx13 3 3.5 10 11.5 4 3B 4B 5B 5B 6B A 4x3x13 8x6x13 3 48 36 33.85 3.5 14.5 10 1.5 16 64 3B 4B 5C 5B 5C 5B 6C 6B B A 8A 10x8x13 6x4x13 3 10 6 48 33.85 3.5 14.5 10 13.5 18 64 3B 4B 5C 5B 5C 5B 6C 6B B A 8A 8x6x13 8x6x15 3 8 6 33.85 14.5 18 16 6 5C 5C 5C 6C 6C B B 8A 8A 10x8x15 8x6x15 3 10 8 68 33.85 14.5 19 18 6 5C 5C 6C 6C B B 8A 8A 10x8x13 8x6x1 3 10 8 86 33.85 14.5 18 6 5C 5C 6C 6C B B 8A 10x8x15 10x8x1 3 10 10 8 33.85 33.85 14.5 14.5 19 19 6 5C 5C 5C 5C 6C 6C B B 8A 8A BASE BASE DIMENSIONS PLATE HA HB HD HE HF HG HH HL HP HT 1A 1 39 9 4.5 36.5 3 0.5 4.5 1.5 3.5 A 15 48 10.5 6 45.5 3.35 0.5 4.5 1.5 3.5 3A 1 45 1 4.5 4.5 3 0.5 4.5 1.5 3.5 3B 1 45 13.5 4.5 4.5 3 0.5 4.5 1.5 3.5 4A 15 5 1.35 6 49.5 3.35 0.5 4.5 1.5 3.5 4B 15 5 14.15 6 49.5 3.35 0.5 4.5 1.5 3.5 5A 18 58 13.5 55.5 3.935 1 4.5 1.5 3.5 5B 18 58 14.5.5 55.5 3.935 1 4.5 1.5 3.5 5C 4 68 19.5 9.5 65.5 4 1 6.5 1.5 5 6A 18 64 13.85.5 61.5 3.935 1 4.5 1.5 3.5 6B 18 64 14.5.5 61.5 3.935 1 4.5 1.5 3.5 6C 4 80 19.5.5.5 4 1 6.5 1.5 5 A 4 68 14.85 9.5 65.5 4 1 4.5 1.5 4.5 B 4 80 19.5 9.5.5 4 1 6.5 1.5 5 8A 4 98 19.5 9.5 95.5 4 1 6.5 1.5 5 FRAME C M 56 13 3.5 143T 13 3.5 145T 14 3.5 18T 15 4.5 184T 16 4.5 MOTOR DIMENSIONS 13T 18 5 FRAME 15T C 0 M 5 54T 56 13 4 3.5 6 143T 56T 13 6 3.5 6 145T 84T 14 3.5 18T 15 4.5 84TS 5 184T 16 4.5 86T 8 13T 18 5 86TS 6 15T 0 5 54T 34T 4 33 68 34TS 56T 6 3 68 84T 36T 34 8 84TS 36TS 5 33 8 86T 8 354T 3 9 86TS 6 364TS 35 9 34T 33 8 34TS 365T 3 39 8 9 365TS 36T 34 3 89 36TS 404T 33 4 10 8 404TS 354T 3 39 10 9 364TS 35 9 405T 44 10 365T 39 9 405TS 41 10 365TS 3 9 444T 4 11 404T 4 10 404TS 444TS 39 44 10 11 405T 445T 44 50 10 11 405TS 445TS 41 46 10 11 444T 44T 4 50 11 444TS 44 11 44TS 445T 50 46 11 445TS 46 11 44T 50 11 44TS 46 11 These These are not are certified not dimensions. certified Certified dimensions. drawings Certified can be obtained drawing on request. can All be dimensions obtained inches. on request. Motor dimensions All dimensions are typical. in inches. Motor dimensions are typical. 6.

PARTS ASME B3.1 / ANSI END SUCTION #1 FRAME GREASE LUBE K-4.0 PART NO. DESCRIPTION PART NO. DESCRIPTION 100 Casing 16 Locknut, Outboard Bearing 101 Stuffing Box Cover 164A Seal, Outboard Bearing 103 Impeller, Open 164B Seal, Inboard Bearing 105 Bearing Cover, Outboard 165A Grease Fitting, Outboard Bearing 106 Split Gland (Packing) 165B Grease Fitting, Inboard Bearing 108 Bearing Housing 10A Pipe Plug, Bearing Housing 116 Bearing Cartridge 10B Pipe Plug, Stuffing Box 11 Flinger 10C Pipe Plug, Bearing Housing Drain 14 Shaft Sleeve 16 Packing 18 Shaft 19 Gland Nut 14A Bearing, Outboard (Thrust) 180A Capscrew, Bearing Cover 14B Bearing, inboard (Radial) 180B Capscrew, Gland 146A Lockwasher, Bearing 180C Capscrew, Bearing Housing to Casing 149 Stud, Gland 181 Allen Set Screw, Bearing Cover 150 Key, Coupling 191A Gasket, Casing 153A Flat Washer, Gland 401A O-Ring, Bearing Cartridge 155 Retaining Ring, Inboard Bearing 401C O-Ring, Shaft Sleeve Refer to pages K-4.4 and K-4.5 for optional stuffing box, seal and gland arrangements..

PARTS ASME B3.1 / ANSI END SUCTION #1 FRAME OIL LUBE K-4.1 PART NO. DESCRIPTION PART NO. DESCRIPTION 100 Casing 164A Seal, Outboard Bearing 101 Stuffing Box Cover 164B Seal, Inboard Bearing 103 Impeller, Open 165A Site Glass / Bottle Oiler 105 Bearing Cover, Outboard 165B Breather / Vent 106 Split Gland (Packing) 10A Pipe Plug, Bearing Housing 108 Bearing Housing 10B Pipe Plug, Stuffing Box 116 Bearing Cartridge 10C Pipe Plug, Bearing Housing Drain 11 Flinger 16 Packing 14 Shaft Sleeve 19 Hex Nut, Gland 18 Shaft 180A Capscrew, Bearing Cover 14A Bearing, Outboard (Thrust) 180B Capscrew, Gland 14B Bearing, inboard (Radial) 180C Capscrew, Bearing Housing to Casing 146A Lockwasher, Bearing 180D Capscrew, Gland Halves 149 Stud, Gland 181 Allen Set Screw, Bearing Cover 150 Key, Coupling 191A Gasket, Casing 153A Flat Washer, Gland 401A O-Ring, Bearing Cartridge 155 Retaining Ring, Inboard Bearing 401C O-Ring, Shaft Sleeve 16 Locknut, Outboard Bearing Refer to pages K-4.4 and K-4.5 for optional stuffing box, seal and gland arrangements. 8.

PARTS ASME B3.1 / ANSI END SUCTION #/3 FRAME GREASE LUBE K-4. PART NO. DESCRIPTION PART NO. DESCRIPTION 100 Casing 16 Locknut, Outboard Bearing 101 Stuffing Box Cover 163 Mechanical Seal 103 Impeller, Open 164A Seal, Outboard Bearing 104 Adaptor 164B Seal, Inboard Bearing 105 Bearing Cover, Outboard 165A Grease Fitting, Outboard Bearing 10 Gland (Mechanical Seal) 165B Grease Fitting, Inboard Bearing 108 Bearing Housing 10A Pipe Plug, Bearing Housing 116 Bearing Cartridge 10B Pipe Plug, Stuffing Box 11 Flinger 10C Pipe Plug, Bearing Housing Drain 14 Shaft Sleeve 180A Capscrew, Bearing Cover 14A Bearing, Outboard (Thrust) 180B Capscrew, Gland 14B Bearing, inboard (Radial) 180C Capscrew, Bearing Housing to Adaptor 146A Lockwasher, Bearing 180D Capscrew, Adaptor to Stuffing Box 149 Stud, Gland 180E Capscrew, Adaptor to Casing 150 Key, Coupling 181 Allen Set Screw, Bearing Cover 153A Flat Washer, Gland 191A Gasket, Casing 153B Flat Washer, Foot 401A O-Ring, Bearing Cartridge 155 Retaining Ring, Inboard Bearing 401B O-Ring, Adaptor to Bearing Frame 15 Frame Support 401C O-Ring, Shaft Sleeve 160 Eyebolt Refer to pages K-4.4 and K-4.5 for optional stuffing box, seal and gland arrangements. 9.

PARTS ASME B3.1 / ANSI END SUCTION #/3 FRAME OIL LUBE K-4.3 PART NO. DESCRIPTION PART NO. DESCRIPTION 100 Casing 164A Seal, Outboard Bearing 101 Stuffing Box Cover 164B Seal, Inboard Bearing 103 Impeller, Open 165B Breather, Bearing Housing 104 Adaptor 165A Sight Gauge, Constant Level Oiler 105 Bearing Cover, Outboard 10A Pipe Plug, Bearing Housing 106 Split Gland (Packing) 10B Pipe Plug, Stuffing Box 108 Bearing Housing 10C Pipe Plug, Bearing Housing Drain 116 Bearing Cartridge 10D Pipe Plug, Bearing Cover 11 Flinger 16 Packing 14 Shaft Sleeve 19 Hex Nut, Gland 18 Shaft 19B Hex Nut, Gland Halves 14A Bearing, Outboard (Thrust) 180A Capscrew, Bearing Cover 14B Bearing, inboard (Radial) 180B Capscrew, Gland 146A Lockwasher, Bearing 180C Capscrew, Bearing Housing to Adaptor 149 Stud, Gland 180D Capscrew, Adaptor to Stuffing Box 150 Key, Coupling 180E Capscrew, Adaptor to Casing 153A Flat Washer, Gland 181 Allen Set Screw, Bearing Cover 153B Flat Washer, Foot 191A Gasket, Casing 155 Retaining Ring, Inboard Bearing 401A O-Ring, Bearing Cartridge 15 Frame Support 401B O-Ring, Adaptor to Bearing Frame 160 Eyebolt 401C O-Ring, Shaft Sleeve 16 Locknut, Outboard Bearing Refer to pages K-4.4 and K-4.5 for optional stuffing box, seal and gland arrangements. 10.

SEAL ARRANGEMENTS ASME B3.1 / ANSI END SUCTION K-4.4 11.

GLAND ARRANGEMENTS ASME B3.1 / ANSI END SUCTION K-4.5 1.

MATERIAL LIST ASME B3.1 / ANSI END SUCTION PART NO. DESCRIPTION ALL IRON STAINLESS STEEL 100 101 103 104 105 106 10 108 11 14 1 133 14A 14B 144 146A 146B 149 150 153A 153B 155A 155B 155C 15 160 16A 163 164A 164B 165A 165B 10A 10B 16 19 180A 180B 180C 180D 180E 180G 191A 191B 401A 401B 401C Casing Stuffing Box Cover Impeller Open Adaptor Outboard Bearing Cover Gland (Packing) Gland (Mechanical Seal) Bearing Housing Flinger Shaft Sleeve Lantern Ring Bearing Sleeve Outboard (Thrust) Bearing Inboard (Radial) Bearing Seal Retaining Ring Bearing Lockwasher Gland Lockwasher Gland Stud Coupling Key Gland Washer Washer (Foot) Outboard Bearing Seal (Outboard) Inboard Bearing Retaining Ring Neck Ring Foot Eyebolt Outboard Bearing Locknut Mechanical Seal Oil Seal (Outboard) Oil Seal (Inboard) Grease Fitting Bearing Housing Vent Bearing Housing Drain Plug Stuffing Box Plug Packing Gland Nut Capscrew (Bearing Housing-Foot) Capscrew (Bearing Housing-Adaptor) Capscrew (Gland) Capscrew (Adaptor-Stuffing Box) Capscrew (Adaptor-Casing) Capscrew (Mechanical Seal Gland) Gasket (Casing) Gasket (Seal Gland) O-Ring (Bearing Cover Outboard) O-Ring (Bearing Housing-Adaptor) O-Ring (Sleeve) Ductile Iron Ductile Iron Ductile Iron Ductile Iron Rubber 316 Stainless 316 Stainless 304-316 Stainless 304-316 Stainless As Per Application Coated As Per Application 304-316 Stainless 304-316 Stainless Aramid Fiber Aramid Fiber Viton 316 Stainless 316 Stainless 316 Stainless Ductile Iron 316 Stainless 316 Stainless Rubber 316 Stainless 316 Stainless 304-316 Stainless 304-316 Stainless As Per Application Coated As Per Application 304-316 Stainless 304-316 Stainless 304-316 Stainless Aramid Fiber Aramid Fiber Viton / Teflon K-5.0 MATERIAL SPECIFICATION FORM MATERIAL SPECIFICATION FORM Ductile Iron ASTM A536 60-45-1 Castings Alloy 0 ASTM A43 CNM Castings ASTM B43 Barstock 316 Stainless ASTM A, A16 WCB ASTM A108 or A56 ASTM A43 CF8M ASTM A6 Casting Barstock Castings Barstock CD4MCU ASTM A890 1B Castings 13.

PUMP DATA ASME B3.1 / ANSI END SUCTION SHAFT BEARINGS STUFFING BOX CASING IMPELLER MODEL CONNECTION SIZE FRAME SIZE DIA. AT CPLG. KEYWAY DIA. BETWEEN BRGS. DISTANCE BETWEEN BRG. CENTERS INBOARD BEARING (RADIAL) OUTBOARD BEARING (THRUST) BORE SLEEVE DIA PACKING SIZE DEPTH NOM. THICKNESS DRAIN CONNECTIONS TEST PRESSURE BASED ON COLD WATER (PSI) MAX. IMP. DIA. MIN. IMP. DIA. 1.5x1x6 3x1.5x6 1.5x1x8 1.5 x 1 3 x 1.5 1.5 x 1 1 1 1 /8 /8 /8 3/16 x 3/3 3/16 x 3/3 3/16 x 3/3 1-/16 1-/16 1-/16 4-4- 4-60 60 60 5306 5306 5306-1/4-1/4-1/4 1-3/8 1-3/8 1-3/8 /16 /16 /16-13/16-13/16-13/16 /16 /16 /16 150 150 5 6-3/8 6-3/8 8 3-4 5 3xx6 3x1.5x8 3xx8 4x3x8 3 x 3 x 1.5 3 x 4 x 3-5/16-5/16-5/16-5/16 150 5 5 5 6-1/4 8-3/4 8-3/4 8-3/4 4 5 5-5- x1x10 3x1.5x10 3xx10 4x3x10 x 1 3 x 1.5 3 x 4 x 3-5/16-5/16-5/16-5/16 300 300 300 300 10 10 10 10 5 6 6 6 K-6.0 3x1.5x13 3xx13 4x3x13 6x4x13 8x6x13 8x6x15 10x8x13 10x8x15 3 x 1.5 3 x 4 x 3 6 x 4 8 x 6 8 x 6 10 x 8 10 x 8 3 3 3 3-3/8-3/8-3/8-3/8 5/8 x 5/16 5/8 x 5/16 5/8 x 5/16 5/8 x 5/16-5/16-5/16-5/16-5/16 10-3/16 10-3/16 10-3/16 10-3/16 10-5/8 10-5/8 10-5/8 10-5/8 6314 6314 6314 6314 5314 5314 5314 5314 3-/8 3-/8 3-/8 3-5/8 3-5/8 3-5/8 3-5/8 3-5/8 300 300 300 300 150 150 150 150 1 1 1 1 13 15 13 15 9 9 9 9 13 15 13 15 * 1 ASME B3.1 / ANSI Pumps not shown 14.

RANGE CHARTS ASME B3.1 / ANSI END SUCTION ALL MODELS K-.0 15.

PHOTOS ASME B3.1 / ANSI END SUCTION K-8.0 16.

PHOTOS ASME B3.1 / ANSI END SUCTION K-8.0 1.

PUMPS ASME B3.1-01 Chemical Process Pumps Size to 10x8x1 Capacity to 6000 USGPM Head to 800 ft. Speed to 3600 rpm Metallurgy, Alloys,, Exotics Double Suction Size to 14x1x16 Capacity to 8000 USGPM Head to 50 ft. Speed to 3600 rpm Metallurgy, Bronze Multi-stage High Pressure Boiler Feed Size to 4xx10 Capacity to 400 USGPM Head to 800 ft. Speed to 3600 rpm Metallurgy, Bronze End Suction Size to 10x8x16 Capacity to 4000 USGPM Head to 400 ft. Speed to 3600 rpm Metallurgy, Alloys, Exotics Non-clog Solids Handling, Vertical/Horizontal Dry Pit Solids Handling Size to 1x10x19 Capacity to 6000 USGPM Head to 50 ft. Speed to 1800 rpm Metallurgy, Bronze, Alloys Refuse Wet Pit/Dry Pit Solids Handling Size to 4x4x10 Capacity to 600 USGPM Head to 100 ft. Speed to 1800 rpm Metallurgy, Alloys Vertical Cantilever Vertical Process Size to 10x8x16 Capacity to 4000 USGPM Head to 300 ft. Speed to 3600 rpm Metallurgy, Alloys, Exotics Vertical Sump Wet Pit Service Size to 10x8x16 Capacity to 4000 USGPM Head to 300 ft. Speed to 3600 rpm Metallurgy, Alloys, Exotics 18.

15.850 M 3 /S 13.08 FLOW H 0 39.3 USGPM IGPM PSI m 1000.48 15.85 13.08 694.4 CFM.119 L/S 5.59 MIGD Ins. Hg kpa mm Hg 60 8.31 86.4 4544 3.6.036 9.9 3.4 3.63 CFS M 3 /D Atmos kg/cm 101.94 M 3 /H.1 6.894 33.96 101.3 Imp Gal CONVERSION CHARTS US Gal 4.0 PRESSURE 9.9.48 3.386.50 Ft 3 M 3 98.0.984 43560 Acre Ft 4 Ft. 3.84 35.31 133.49 1.0 64. 3.683 0.14 Multiply in direction of arrow. Divide in opposite direction. Multiply in direction of arrow. Divide in opposite direction. 454.6 MIG English Metric Decimal English Metric Decimal English Metric Decimal English Metric Decimal...1.0039 45...080 5...055 /16...435..009 44...0860 4...090 9/64...4531...3.0118 43...0890 3...130 15/3...468 80...0135 4...0935 /3..18.. 1..44 9..0145 3/3...093...10 31/64...4844 1/64...0156 41...0960 1.. 80...5000...4.015 40...0980 A...340.. 13..5118 8..0160 39...0995 15/64...344 33/64.. 5156..0180 38...1015.. 6..36 1/3...531..5.019 3...1040 B...380 35/64...5469 6..000 36...1065 C...40.. 14..551 5..010 /64...1094 D...460...565 4..05 35...1100 1/4...500 3/64...581..6.036 34...1110 F...50.. 15..5906 3...040 33...1130 G...610 19/3...593...050 3...1160 1/64...656 39/64...6094 1...060.. 3..1181 H...660 5/8...650....06 31..100 I...0.. 16..699 0...080 1/8...150....56 41/64...6406 69...09 30...185 J...0 1/3...656 68...0310 9...1360 K...810.. 1..6693 1/3...031 8...1405 9/3...81 43/64...619...8.0315 9/64...1406 L...900 11/16...685 6...030...1440 M...950 45/64...031 66...0330 6..140 19/64...969.. 18..08 65...0350 5...1495 N...300 3/3...18..9.0354 4...150 5/16...315 4/64...344 64...0360 3...1540.. 8..3150.. 19..480 63...030 5/3..156 O...3160 3/4...500 6...0380...150 P...330 49/64...656 61...0390.. 4..155 1/64...381 5/3...81.. 1..0394 1...1590 Q...330.. 0..84 60...0400 0...1610 R...3390 51/64...969 59...0410 19...1660 11/3...343 13/16...815 58...040 18..1695 S...3480.. 1..868 5..0430 11/64...119.. 9..3543 53/64...881 56...0465 1..130 T...3580 /3...843 3/64...0469 16...10 3/64...3594 55/64...8594 55...050 15...1800 U...3680....8661 54...0550 14...180 3/8...350 /8...850 53...0595 13...1850 V.30 5/64...8906 1/16..065 3/16...185 W...3860.. 3..9055 5...0635 1...1890 5/64...3906 9/3...906 51...060 11...1910.. 10..393 59/64...919 50...000 10...1935 X...390 15/16...935 49..030 9...1960 Y..4040.. 4..9449 48...060.. 5..1968 13/3...406 61/64...9531 5/64...081 8...1990 Z...4130 31/3...968 4...085...010 /64...419.. 5..984....08 13/64...031.. 11..4331 63/64...9844 46...0810 6...040 1 5.4 1.000 Nom. Size Tap Use Drill Bit (Closest) Decimal 0-80 NF 3/64 3/64.0469 1-64 NC #53 -.0595 1- NF #53 1/16.0595-56 NC #50 -.000-64 NF #50 -.000 3-48 NC #4 5/64.085 3-56 NF #45 -.080 4-36 NS #44 -.0860 4-40 NC #43 3/3.0890 4-48 NF #4 3/3.0935 3mm-0.60mm.5mm -.0984 1/8-40 NS #38 -.1015 5-40 NC #38 -.1015 5-44 NF #3 -.1040 6-3 NC #35 /64.1100 6-36 NS #34 -.1110 6-40 NF #33 -.1130 6-48 NS #31 -.100 4mm-0.0mm 3.4mm -.1338 4mm-0.5mm 3.4mm -.1338 8-3 NC #9 -.1360 8-36 NF #9 9/64.1360 8-40 NS #8 -.1405 3/16-4 NS #6 -.140 10-4 NC #5 5/3.1495 3/16-3 NS # -.150 10-3 NF #1 5/3.1590 5mm-0.90mm 4.mm -.1653 5mm-0.80mm 4.3mm -.1693 1-4 NC #16 11/64.10 1-8 NF #14 3/16.180 1-3 NEF #13 -.1850 DECIMAL EQUIVALENTS TAP DRILL CHART RECOMMEND TAP DRILL TO USE FOR 5% DEPTH OF THREAD Nom. Size Tap Use Drill Bit (Closest) Decimal Nom. Size Tap Use Drill Bit (Closest) Decimal 14-0 NS #10 -.1935-1 NC 31/64 31/64.4844 1/4-0 NC # 13/64.010 14mm-1.50mm 1.mm -.4999 14-4 NS # -.010 14mm-1.5mm* 1.8mm -.5039 6mm-1.00mm 5.mm -.04-18 NF 33/64 33/64.5156 1/4-4 NS #4 -.090 5/8-11 NC 1/3 1/3.531 1/4-8 NF #3 /3.130 16mm-.00mm 14.mm 35/64.5590 1/4-3 NEF /3 /3.188 5/8-18 NF 3/64 3/64.581 1/4-40 NS #1 -.80 16mm-1.50mm 14.mm -.58 mm-1.00mm 6.1mm 15/64.401 11/16-11 NS 19/3 19/3.5938 5/16-18 NC Ltr.F 1/64.50 18mm-.50mm 15.8mm 39/64.60 8mm-1.5mm 6.9mm 1/64.16 11/16-16 NS 5/8 5/8.650 5/16-4 NF Ltr.I -.0 3/4-10 NC 1/3 1/3.656 8mm-1.00mm.1mm -.95 18mm-1.50mm* 16.8mm -.6614 5/16-3 NEF 9/3 9/3.81 3/4-16 NF 11/16 11/16.685 9mm-1.5mm.9mm -.3110 0mm-.50mm 1.8mm 11/16.008 3/8-16 NC 5/16 5/16.315 /8-9 NC 49/64 49/64.656 9mm-1.00mm 8.1mm -.3189 /8-14 NF 13/16 13/16.815 9mm-0.5mm 8.3mm -.368 mm-1.50mm 0.9mm -.88 3/8-4 NF Ltr.Q 1/64.330 /8-18 NS* 53/64 53/64.881 10mm-1.50mm 8.mm -.345 4mm-3.00mm 1.4mm 53/64.845 10mm-1.5mm 8.9mm 11/3.3503 1.8 NC /8 /8.850 10mm-1.00mm 9.1mm -.3583 4mm-.00mm.3mm -.89 /16-14 NC Ltr.U 3/64.3680 1.1 NF 59/64 59/64.919 11mm-1.50mm 9.mm -.3818 1-14 NS 15/16 15/16.935 /16-0 NF 5/64 5/64.3906 1 1/8- NC 63/64 63/64.9844 1mm-1.5mm 10.5mm -.4133 1 1/8-1 NF 1 3/64 1 3/64 1.0469 1mm-1.50mm 10.mm /64.41 1 1/4- NC 1 /64 1 /64 1.1094-13 NC /64 /64.419 1 1/4-1 NF 1 11/64 1 11/64 1.119 1mm-1.5mm* 10.9mm /64.491 1 3/8-6 NC 1 /3 1 /3 1.188-0 NF 9/64 9/64.4531 1 3/8-1 NF 1 19/64 1 19/64 1.969-4 NS 9/64 9/64.4531 1-6 NC 1 11/3 1 11/3 1.3438 14mm-.00mm 1.mm -.4803 1-1 NF 1 /64 1 /64 1.419 4.543 1000 1.31 5941 L 6100 Yd 3 VOLUME 61.0 In 3 46656 Multiply in direction of arrow. Divide in opposite direction. Smart Turner Pumps Inc. 39 Hardy Road, P.O. Box 8066, Brantford, Ontario, N3RX5, Canada 19. TEL: 1-888-561-PUMP (86) FAX: (519) 5-14 EMAIL: contact@smartturner.ca Website: www.smartturner.ca

ASME B3.1 / ANSI END SUCTION PUMPS This catalogue provides the information you need to select a Smart Turner ASME B3.1 Pump to fit your specific needs. The ASME End Suction Pump range continues the Smart Turner tradition of providing well proven, uncomplicated designs incorporating high efficiency and smooth, low NPSH performance in a compact economical, Heavy Duty End Suction Pump. Smart Turner ASME Pumps are ideally suited to plant service and chemical process applications where continuous, reliable operation is essential, whether the fluid is clean, dirty, corrosive or abrasive. Smart Turner ASME Pumps are quality built for rugged, trouble free operation. They are available with either grease or oil lubricated bearings as standard. Smart Turner ASME Pumps are engineered to exceed ANSI standards in all essential features. Impeller adjustment is positive and uncomplicated. High shaft stiffness yields low shaft deflections. Oversize bearings provide more than year L10 life in all cases. The large stuffing box and the rear impeller pump out vanes provide excellent heat dissipation and low stuffing box pressure for long packing and seal life. The recessed pump out vane arrangement minimizes the effects of wear by maintaining pump out efficiency throughout the full range of impeller adjustment. Smart Turner ASME Pumps are produced and stocked in a wide range of sizes using only three bearing housings. This makes an efficient parts inventory possible through extensive interchangeability of parts between pumps. With the inclusion of ASME Pumps, Smart Turner can now offer a range of End Suction Pumps, totaling over 60 models, with capacities to 6000 USGPM, heads to 800 feet and speeds to 3500 Rpm. This HEAD catalogue OFFICE features AND MAIN ANSI End SALES Suction OFFICE: Pumps. For other End Suction models, Smart see Turner catalogues Pumps Inc. B-90, D-90, F-90 and G-90. 39 Hardy Road, P.O. Box 8066, Brantford, Ontario, N3RX5, Canada TEL: (519) 5-146 FAX: (519) 5-14 Website: www.smartturner.ca DISTRIBUTION: Smart Turner Pumps Inc. takes great pride in it s global distribution network. If you need it we will ship it, anywhere in the world. REPRESENTED BY: 0. CONSTRUCTION MATERIALS All Iron 316 Stainless Alloy 0 CD4MCuN Hastelloy C Bronze Monel Other Materials on Application