Window and Door Technology Roto NT The world s biggest selling Tilt&Turn hardware system for windows and balcony doors Installation, maintenance and operation instructions for PVC windows and balcony doors
Imprint Copyright: January 2017 Roto Frank AG Window and Door Technology Wilhelm-Frank-Platz 1 70771 Leinfelden-Echterdingen Germany Phone +49 711 7598 0 Fax +49 711 7598 253 info@roto-frank.com www.roto-frank.com
General information Contents General information Information on these instructions...5 Responsibility of the target groups...7 Instruction obligation of the target groups...8 Explanation of the safety instruction symbols...9 Limitation of liability... 10 Safety Stipulated use... 11 Stipulated application for end-users... 12 Safety instructions... 13 Safety information for end-users... 14 Fabrication advice... 15 Screw fixing... 16 Information on the product General hardware characteristics... 18 Introduction... 19 Dimensional data for hardware... 20 Frame clearance... 21 Application diagram... 23 Hardware overview Explanation on the hardware overview chapter... 33 Tilt&Turn hardware Basic security... 34 Tilt&Turn hardware RC1 N (DIN EN 1627 1630)... 36 Tilt&Turn hardware RC2 / RC2 N (DIN EN 1627 1630)... 38 Tilt&Turn hardware Comfort Basic security... 40 Turn-Only hardware Basic security... 42 Turn-Only hardware RC1 N (DIN EN 1627 1630)... 44 Turn-Only hardware RC2 / RC2 N (DIN EN 1627 1630)... 46 Tilt-Only hardware Basic security... 48 Turn-Only / Tilt&Turn hardware Basic security... 50 Turn-Only / Tilt&Turn hardware RC1 N (DIN EN 1627 1630)... 54 Turn-Only / Tilt&Turn hardware RC2 / RC2 N (DIN EN 1627 1630)... 58 Turn-Only / Tilt&Turn hardware Comfort Basic security... 62 Tilt&Turn hardware for pitched windows Basic security...64 Tilt&Turn hardware for arched windows Basic security...66 Stay guide / Stay arm / Stay bearing... 68 System 12 / 18-9...68 System 12 / 20-9...68 System 12 / 18-13...69 System 12/20-13...69 System 12/21-13...69 System 12/22-13...69 Subject to change. Roto NT IMO_63_EN_v3 January 2017 3
General information Contents Lever-operated espagnolette & T&T espagnolette: possible combinations... 70 Lever-operated espagnolette Plus / T&T espagnolette: possible combinations... 71 Profile-related components... 72 Croppers... 76 Installation Drilling the sash drill-holes... 77 Install the handle... 78 Frame... 79 Sash... 80 Sash... 81 Pitched window sash... 83 Arched window sash... 85 Hinging the sash... 88 Fixing suggestion installation of security windows... 90 Installation drawings Installation of frame components... 92 Jigs... 112 Adjustment Explanation on the adjustment chapter... 114 Adjustment instructions... 115 Operation Operating information... 118 Operation information for end-users... 119 Troubleshooting... 120 Maintenance Maintenance... 122 Lubrication points... 123 Inspection and care... 124 Preservation of the surface finish... 125 Dismantling Unhinging the sash... 127 Transport Transport, packaging, storage... 128 Transport inspection... 129 Disposal Disposal of window hardware... 130 4 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
General information Information on these instructions This manual contains important information, instructions and application diagrams (maximum sash sizes and sash weights) as well as installation instructions regarding the further work of the hardware. Also, this manual contains binding guidelines to ensure the duty to instruct through to the end-user. The information and instructions in this manual refer to the products of the Roto NT hardware system. Apart from these installation, maintenance and operation instructions, the following documents apply: Catalogue Directives of the Quality Assurance Association: Locks and Hardware (Richtlinie der Gütegemeinschaft Schlösser und Beschläge e. V.) Directives VHBE of the Quality Assurance Association: Locks and Hardware (Richtlinie VHBE der Gütegemeinschaft Schlösser und Beschläge e. V.) This manual should be stored in such a manner that it can be quickly used, if needed. Additional markings To highlight handling directives, results, lists, references and other elements, the following signs are used in this manual: Marking Explanation Sash Frame Drill-holes 1 Hardware components 1. Action steps First level of the hierarchy in a list Unordered list (second level of hierarchy) P. 12 Refer to page 12 (Cross) reference in tables (Cross) reference in the text Subject to change. Roto NT IMO_63_EN_v3 January 2017 5
General information Information on these instructions Marking HA DIN L / R T&T SRW SRH S.kg CON CL LMD not dep. Explanation Hardware axis DIN left / right Tilt&Turn hardware Sash rebate width Sash rebate height Sash weight Connectable Centre lock Lifting mishandling device not depicted RC1 N Resistance Class 1 RC2 / RC2 N Resistance Class 2 SEC Security All dimensions stated in mm. Other values are specified. Protection of copyright The contents of this manual are protected by copyright. In the framework of the hardware manufacturing, the use of the contents is allowed. Any other or further use is not permitted without written permission of the manufacturer. 6 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
General information Responsibility of the target groups The information in this document is aimed at the following target groups: Hardware dealers The hardware dealers target group includes all companies/persons who purchase hardware from the hardware manufacturer to resell it without the hardware being modified or subject to further work. Manufacturers of windows and balcony doors The manufacturers of windows and balcony doors target group includes all companies/persons who purchase hardware from the hardware manufacturer or the hardware dealer and build it into windows and balcony doors. Building element dealers/installation company The building element dealers target group includes all companies/persons who purchase windows and balcony doors from the manufacturer of windows and balcony doors in order to sell these on and to install them into a building development, without the windows or balcony doors being modified. The installation company target group includes all companies/persons who purchase windows and balcony doors from the manufacturer of windows and balcony doors, or from a building element dealer, in order to sell these and to install them into a building development, without the windows or balcony doors being modified. Builder The builder target group includes all companies/persons who order windows and/or balcony doors for installation into their building project. End-users The end-users target group includes all persons who operate the installed windows and/or balcony doors. Subject to change. Roto NT IMO_63_EN_v3 January 2017 7
General information Instruction obligation of the target groups NOTE! Every target group must fully comply with its instruction obligation. Unless defined otherwise in the following, the documents and information may be transmitted e.g. as printed documents, CD-ROM, or via Internet access. Responsibility of the hardware dealer The hardware dealer must transmit the following documents to the manufacturer of windows and balcony doors: Catalogue Installation, maintenance and operation instructions Directive for fixing load-bearing Turn-Only and Tilt&Turn hardware components (TBDK) Guidelines/advice on the product and on liability (VHBH) Guidelines/advice for end-users (VHBE) Responsibility of the manufacturer of windows and balcony doors The manufacturer of windows and balcony doors must transmit the following documents to the building element dealer or to the builder, even when a subcontractor (installation company) is acting as an intermediary: Installation, maintenance and operation instructions Directive for fixing load-bearing Turn-Only and Tilt&Turn hardware components (TBDK) Guidelines/advice on the product and on liability (VHBH) Guidelines/advice for end-users (VHBE) He must ensure that the end-user is provided with the documents and information intended for him, in printed format. Responsibility of the building element dealer/installation company The building element dealer must transmit the following documents to the builder, even when a subcontractor (installation company) is acting as an intermediary: Maintenance and operating instructions (with the focus on hardware) Guidelines/advice on the product and on liability (VHBH) Guidelines/advice for end-users (VHBE) Responsibility of the builder The builder must transmit the following documents to the end-user: Maintenance and operating instructions (with the focus on hardware) Guidelines/advice for end-users (VHBE) 8 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
General information Explanation of the safety instruction symbols In this manual, safety information is indicated by a symbol. The safety information is introduced by a key word that indicates the severity of the danger. DANGER! This symbol in conjunction with the signal word indicates an imminently hazardous situation, which could result in death or serious damage to health if it is not avoided. WARNING! This symbol in conjunction with the signal word indicates a potentially dangerous situation, which could result in death or serious damage to health if it is not avoided. CAUTION! This symbol in conjunction with the signal word indicates a potentially dangerous situation, which may lead to minor or light injuries if it is not avoided. NOTE! This symbol in conjunction with the signal word indicates a potentially dangerous situation, which may lead to property or environmental damage if it is not avoided. Subject to change. Roto NT IMO_63_EN_v3 January 2017 9
General information Limitation of liability All details and instructions in this document were compiled taking into account the relevant standards and regulations, the state of the art, and also many years of knowledge and experience. The hardware manufacturer accepts no liability for damages resulting from: Failure to comply with this document and all product-specific documents and related applicable directives (refer to the chapters Safety and Stipulated use). Non-stipulated use/misuse (refer to the chapters Safety and Stipulated use). Insufficient invitation to tender, failure to adhere to the installation instructions or application drawings. Increased soiling. Claims by third parties against the hardware manufacturer on the ground of damages resulting from misuse or failure to follow the instruction obligation on the part of the hardware dealer, the manufacturer of windows and balcony doors, and of the building element dealer or the builder are transferred accordingly. The undertakings agreed in the delivery contract, the general conditions of business and the delivery conditions of the hardware manufacturer, and the legal regulations applicable at the time of concluding a contract are effective. The warranty covers only original Roto components. The right to technical modifications for the improvement of performance characteristics and for further development is reserved. 10 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
Safety Stipulated use Turn-Only and Tilt&Turn hardware is one-hand operation Turn-Only and Tilt&Turn hardware for windows and balcony doors in building construction. This is used to enable windows and balcony-door sashes into a turning position by operating a hand-lever (handle) or into a limited tilting position in the case of the scissors (sash-stay) version. Turn-Only and Tilt&Turn hardware is used on vertically installed windows and balcony-doors made of timber, PVC, aluminium or steel and their corresponding material combinations. Turn-Only and Tilt&Turn hardware as covered by this definition, locks window and balcony door sashes or enables various ventilating positions. When closing, the gasket counter force must be overcome as a rule. Correct use also includes adhering to all the specifications in the productspecific documents, such as: These installation, maintenance and operation instructions Product catalogues Information and specifications of the profile manufacturer (e.g. PVC or light metal profiles etc.) The relevant directives TBDK and VHBE of the Quality Assurance Association: Locks and Hardware (Gütegemeinschaft Schlösser und Beschläge e. V.) The valid national laws and directives Any type of use that goes beyond or differs from the defined correct use shall be regarded as misuse. WARNING! Danger from misuse! Misuse and incorrect installation of hardware can result in hazardous situations. Never use hardware combinations that have not been approved by the hardware manufacturer. Never use accessories that are not original products or that have not been approved by the hardware manufacturer. Subject to change. Roto NT IMO_63_EN_v3 January 2017 11
Safety Stipulated application for end-users Turn-Only and Tilt&Turn hardware For windows and balcony doors with Turn-Only or Tilt&Turn hardware, window and balcony door sashes can be brought into a turn position or into a limited tilting position by means of the scissor stay. When a sash is closed and the hardware is locked, the resistance of a gasket usually needs to be overcome. WARNING! Danger of injury and material damage from incorrect closing and opening the sash! Incorrect closing and opening of sashes can result in serious injuries and significant material damage. Therefore: Ensure that when closing the sash, it does not collide with the frame or with another sash. Ensure that the sash is guided slowly by hand throughout the entire range of movement as far as the fully closed position, and that it is brought very slowly towards the frame. Ensure that the sash never slams closed or swings open in an uncontrolled manner. Any use beyond or other than the stipulated application and installation of the products is deemed to be misuse and can result in dangerous circumstances. WARNING! Danger from misuse! Misuse of windows and balcony doors can result in dangerous circumstances. In particular, avoid the following applications: insertion of obstacles in the opening area between the frame and the window or balcony door sashes, the deliberate or negligent application of excessive loads on windows and balcony doors, deliberate or uncontrolled slamming or pushing of windows and balcony doors against the window reveal. This can destroy the hardware, frame materials, or other individual components of the windows or balcony doors. Claims for damages of any type whatsoever resulting of operation other than that stipulated are excluded. 12 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
Safety Safety instructions Turn-Only and Tilt&Turn hardware, Safety relevant symbols Comply with the following symbols and their meanings in order to avoid accidents, injuries and material damage. Symbol Meaning DANGER! Danger of injury from falling through open windows and balcony doors. Proceed cautiously in the vicinity of open windows and balcony doors. Please keep children and persons that cannot appreciate the danger away from the hazard area. WARNING! Danger of injury through trapping of body parts in the opening gap between sash and frame. When closing windows and balcony doors, never reach between sash and frame, and always act with care. Please keep children and persons that cannot appreciate the danger away from the hazard area. WARNING! Danger of injury and material damage from overloading the sash Refrain from additionally loading the sash. CAUTION! Danger of injury from the effect of wind Prevent wind from acting on the open sash. During wind and draughts, close and lock windows and balcony door sashes. CAUTION! Danger of injury and material damage from insertion of obstructions into the opening gap between sash and frame Refrain from inserting obstacles in the opening gap between the sash and the frame. CAUTION! Danger of injury and material damage from pressing the sash against the opening edge (reveal) Do not press the sash against the opening edge (reveal). Subject to change. Roto NT IMO_63_EN_v3 January 2017 13
Safety Safety information for end-users Turn-Only and Tilt&Turn hardware, Safety relevant symbols The following symbols can be used on windows and balcony doors to protect the end-user. Always keep these symbols in a clearly legible state. Please order stickers separately (OPR_16_DE-EN). Sicherheitshinweis Security advice 08/2012 OPR_16_DE-EN_v1 14 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
Safety Fabrication advice Maximum sash sizes and weights The technical data, application diagrams, and component classifications in the product-specific documentation of the hardware manufacturer give instructions on the maximum permitted sash sizes and weights. Here, the component with the smallest permitted load bearing capacity decides the maximum permitted sash weight. Check compliance of the technical data, application diagrams, and component classifications before the use of electronic data sets, and especially their use in fenestration programmes. The maximum permitted sash sizes and weights must never be exceeded. In the case of uncertainty contact the hardware manufacturer. Guidelines from the profile manufacturer The manufacturer of windows and/or balcony doors must comply with all specified system-related dimensions (e.g. gasket gap dimensions or lockingpoint distances). Furthermore, he must check these regularly and make certain of them, especially on the first use of new hardware components, during manufacture, in an ongoing manner up to and including the window installation. NOTE! The hardware parts must always be designed such that the systemrelated dimensions - insofar as they are affected by the hardware - can be adjusted. If a deviation from these dimensions is noticed only after the installation of the windows, the hardware manufacturer is not responsible for any possible additional work arising. Composition of hardware Burglary inhibiting windows and balcony doors require hardware which fulfils particular requirements. Windows and balcony doors for damp rooms, and those for use in environments with aggressive and corrosive air components require hardware which fulfils particular requirements. The resistance of windows and balcony doors to wind loads when closed and locked depends on the actual designs of the windows and balcony doors. Wind loads prescribed by law and standards (e.g. as per EN 12210 especially test pressure P3) can be dissipated by the hardware system. In general, the Turn-Only and Tilt&Turn hardware defined in this document is able to fulfil legal and standard requirements for barrier-free habitations. The hardware combinations and installations appropriate for windows and balcony doors in the previously mentioned areas should be specifically selected and agreed with the hardware manufacturer and the profile manufacturer. NOTE! The guidelines of the hardware manufacturer relating to the combination of the hardware (e.g. the use of additional stay arms, the design of hardware for burglary-inhibiting sashes for windows and balcony doors, etc.) are binding. Subject to change. Roto NT IMO_63_EN_v3 January 2017 15
Safety Screw fixing DANGER! Danger to life from incorrectly installed and threaded hardware components! Incorrect installation and threading of hardware components can result in dangerous circumstances and cause severe accidents, even including death. Therefore: For installation and especially for threaded components, observe the product-specific documentation of the hardware manufacturer, the information from the profile manufacturer, and all contents of the TBDK directive of the Gütegemeinschaft Schlösser und Beschläge. For fixing the hardware components, Ø 3.9 4.2 x... zinc plated and passivated steel fenestration screws are to be used. In the case of special climatic conditions, use fenestration screws with additional sealing. The window fabricator must ensure adequate fixing of the hardware components, consulting the screw manufacturer if necessary. When fixing security relevant, supportive hardware components such as stay bearings and pivot rests, the tearing-forces horizontal to the sash plane surface must be reached in accordance with the following tables (the tractive-force values depend on the sash weights from the TBDK). Sash weight in kg Tractive force in N 1) 60 1650 70 1900 80 2200 90 2450 100 2700 110 3000 120 3250 130 3500 1) Acceptable tolerance -10%. The stated values refer to the stay bearing. These are also valid for the pivot rest if the fixing is carried out in the same manner as with the stay bearing. On sash weights up to 80 kg the table s values are reached as a rule, if highquality screws are applied and the screw-fixing into the profile penetrates at least 2 profile walls, whereby the first profile-chamber wall should be at least 2.8 mm thick. For sash weights over 80 kg, a supplementary fixing into the reinforcement profile or profile insertions according to the profile system, is necessary. By means of applying the 130 kg sash weight frame hinges, the required value can be achieved also without supplementary measures. Do not use any acid cross-linked sealing compounds that could lead to corrosion of the hardware components. The glazing spacer-block regulations for the glazing procedure are to be adhered to. 16 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
Safety Screw fixing Fixing suggestion installation of security windows Horizontal cross section M 1:2 Fixing SEC striker 3 screws 4 x... (If no fixing into the steel reinforcement is possible, screw through all profile walls) Fixing glazing-beads Use screws if required Vertical cross section M 1:2 Subject to change. Roto NT IMO_63_EN_v3 January 2017 17
Information on the product General hardware characteristics Roto NT General hardware characteristics Profiled faceplate. Effortless operation with low abrasion due to guided adjustable locking cams. Easy adjustment of the locking cams with standard tools. E cam: gasket-compression adjustable eccentric cam and/or P cam: gasket-compression adjustable eccentric security cam and/or V cam: height and gasket-compression adjustable eccentric security cam Strong interlocking Clip&Fit connection without loss of cam travel Link-slider guided stay arm, as standard with Integrated anti-slam device Variable tilt restrictor (80 140 mm) Turn restriction Mishandling device in tilted position (only T&T version) Stay bearing and pivot rest flush with the overlap. High-quality Roto Sil Nano surface-finish (matt-silvery) for maximum corrosion resistance (DIN EN 13126 / 8 Class 4) using Nano particles (free from Chromium VI compounds). 10-year warranty on the operativeness of the hardware 3D adjustment in stay arm / corner hinge / pivot rest Frame clearance of 12 / 20: 2 / 20 / 2 mm (top/ hinge side / bottom) resp. 15 / 20 / 15 mm (top / laterally / bottom) for 130 kg. Low-maintenance Tested in accordance with 13126-8: 2006-02 and EN 1191: 2000-08 and certified according to QM 328. Handles and cover caps are available in different RAL colours. With burglar-inhibiting anti-jemmy device in the tilt striker as standard. 18 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
Information on the product Introduction Locking cam E Gasket-compression adjustable cam Locking cam P Gasket-compression adjustable security mushroom cam Locking cam V Height and gasketcompression adjustable security mushroom cam Three locking cam versions The Roto NT hardware system offers 3 different locking cam versions that differ in application and adjusting capabilities. The detailed adjusting dimensions can be found in these installation instructions. The NT striker concept All strikers in the Roto NT hardware system have identical screwing axes. This concept renders prefitting the sash with security cams possible, and a later frame retrofitting with security strikers (zinc or steel). All locking cam versions are combinable with all strikers. The surface-finish Roto Sil Nano surface-finish for elegant matt silvery aesthetics. Unmistakable consistent silver look. Optimal protection by means of galvanising, chromating, and additional sealing. Increased corrosion protection. The NT security concept The basic version of Roto NT is already equipped with basic security on the bottom horizontal sash-plane. Highest burglary inhibition results are achieved with exemplary hardware combinations for security windows in accordance with DIN EN 1627 1630. This standard includes an overall test of all individual window components. Subject to change. Roto NT IMO_63_EN_v3 January 2017 19
Information on the product Dimensional data for hardware 2.2 9.3 Sash profile cross section Dimensional data for hardware 16.2 12.3 20 20 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
Information on the product Frame clearance Including cover cap Sash weight 100 kg Top 20 Bottom 2 20 Subject to change. Roto NT IMO_63_EN_v3 January 2017 21
Information on the product Frame clearance Including cover cap Sash weight 130 kg 15 Top 20 Bottom 15 20 22 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
Information on the product Application diagram Hinge side K 3/100, K 6/100 Turn-Only/Tilt&Turn hardware for rectangular windows Application diagram Hinge side K 3/100, K 6/100 Turn-Only/Tilt&Turn hardware for rectangular windows Limitation of sash formats depending on the glass thickness Application range Sash rebate width SRW...290 1600 mm 2500 50 kg/m 2 40 kg/m 2 30 kg/m 2 Sash rebate height SRH...280 2600 mm Sash weight S.kg...max. 100 kg 2000 Security RC1 N Sash rebate width SRW...320 1400 mm Sash rebate height SRH...280 2600 mm 1500 Sash weight S.kg...max. 100 kg Security RC2 / RC2 N Sash rebate width SRW...400 1400 mm Sash rebate height SRH...490 2400 mm Sash weight S.kg...max. 100 kg SRH 280 2600 mm 1000 500 The information in the application diagram refers to the glass weight in kg/m 2. 500 1000 1500 SRW 290 1600 mm 1 mm/m 2 glass thickness = 2.5 kg = Impermissible application range = Additional scissor stay required Subject to change. Roto NT IMO_63_EN_v3 January 2017 23
Information on the product Application diagram Hinge side K 6/130 Turn-Only/Tilt&Turn hardware for rectangular windows Application diagram Hinge side K 6/130 Turn-Only/Tilt&Turn hardware for rectangular windows Limitation of sash formats depending on the glass thickness 60 kg/m 2 50 kg/m 2 40 kg/m 2 Application range Sash rebate width SRW...290 1600 mm 2500 Sash rebate height SRH...280 2600 mm Sash weight S.kg...max. 130 kg 2000 Security RC1 N Sash rebate width SRW...320 1400 mm Sash rebate height SRH...280 2600 mm Sash weight S.kg...max. 130 kg Security RC2 / RC2 N Sash rebate width SRW...400 1400 mm Sash rebate height SRH...490 2400 mm Sash weight S.kg...max. 130 kg SRH 280 2600 mm 1500 1000 500 The information in the application diagram refers to the glass weight in kg/m 2. 500 1000 1500 SRW 290 1600 mm 1 mm/m 2 glass thickness = 2.5 kg = Impermissible application range = Additional scissor stay required 24 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
Information on the product Application diagram Hinge side K and A Tilt&Turn hardware for pitched windows 25 Application diagram Hinge side K and A Tilt&Turn hardware for pitched windows 25 Limitation of sash formats depending on the glass thickness Application range Sash rebate width SRW... see diagram 2280 Sash rebate height SRH... see diagram Sash weight S.kg...max. 80 kg 2000 The information in the application diagram refers to the glass weight in kg/m 2. 1 mm/m 2 glass thickness = 2.5 kg = Impermissible application range SRH espagnolette side in mm 1500 1000 500 350 265 25 500 1000 1600 960 SRH hinge side in mm SRW in mm Subject to change. Roto NT IMO_63_EN_v3 January 2017 25
Information on the product Application diagram Hinge side K and A Tilt&Turn hardware for pitched windows 40 Application diagram Hinge side K and A Tilt&Turn hardware for pitched windows 40 Limitation of sash formats depending on the glass thickness Application range Sash rebate width SRW... see diagram 2215 Sash rebate height SRH... see diagram Sash weight S.kg...max. 80 kg 2000 The information in the application diagram refers to the glass weight in kg/m 2. 1 mm/m 2 glass thickness = 2.5 kg = Impermissible application range SRH espagnolette side in mm 1500 1000 500 350 225 40 500 1000 1600 1440 SRH hinge side in mm SRW in mm 26 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
Information on the product Application diagram Hinge side K and A Tilt&Turn hardware for pitched windows 50 Application diagram Hinge side K and A Tilt&Turn hardware for pitched windows 50 Limitation of sash formats depending on the glass thickness Application range Sash rebate width SRW... see diagram Sash rebate height SRH... see diagram Sash weight S.kg...max. 80 kg The information in the application diagram refers to the glass weight in kg/m 2. 1 mm/m 2 glass thickness = 2.5 kg = Impermissible application range SRH espagnolette side in mm 2180 2000 1500 1000 500 50 1815 SRH hinge side in mm 350 200 500 SRW in mm 1000 1230 Subject to change. Roto NT IMO_63_EN_v3 January 2017 27
Information on the product Application diagram Hinge side K and A Tilt&Turn hardware for pitched windows 15 Application diagram Hinge side K and A Tilt&Turn hardware for pitched windows 15 Limitation of sash formats depending on the glass thickness Application range Sash rebate width SRW... see diagram Sash rebate height SRH... see diagram Sash weight S.kg...max. 80 kg 2325 2000 2100 The information in the application diagram refers to the glass weight in kg/m 2. 1 mm/m 2 glass thickness = 2.5 kg = Impermissible application range SRH espagnolette side in mm 1500 1000 500 15 1600 SRH hinge side in mm 350 280 500 1000 1120 250 SRW in mm 28 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
Information on the product Application diagram Hinge side K Tilt&Turn hardware for arched windows Application diagram Hinge side K Tilt&Turn hardware for arched windows Limitation of sash formats depending on the glass thickness 40 kg/m 2 30 kg/m 2 20 kg/m 2 Application range Sash rebate width SRW...400 1300 mm Sash rebate height SRH...500 1900 mm Sash weight S.kg...max. 80 kg The information in the application diagram refers to the glass weight in kg/m 2. SRH to start of the arch in mm 1500 1000 1 mm/m 2 glass thickness = 2.5 kg 500 500 1000 SRW in mm = Impermissible application range = Additional scissor stay required = Additional scissor stay possible, however not required = Additional scissor stay not possible Subject to change. Roto NT IMO_63_EN_v3 January 2017 29
Information on the product Application diagram Hinge side K Tilt-Only hardware for rectangular windows Application diagram Hinge side K Tilt-Only hardware for rectangular windows Limitation of sash formats depending on the glass thickness Application range Sash rebate width SRW...310 2400 mm 1000 Sash rebate height SRH...290 1200 mm Sash weight S.kg...max. 80 kg SRH in mm 550 500 The information in the application diagram refers to the glass weight in kg/m 2. 500 621 1000 1500 2000 1 mm/m 2 glass thickness = 2.5 kg at least 2 hinges at least 3 hinges SRW in mm = Impermissible application range = 2 tilt-stays laterally = 1 tilt-stay on top or 2 tilt-stays laterally = 2 tilt-stays on top or 2 tilt-stays laterally = Restrictor and cleaning stays required in addition = Additional restrictor and cleaning stays for top tilt-stay(s) Please note: Restrictor and cleaning stays are recommended; and necessary on fanlights (in accordance with RAL RG 607 / 12) For restrictor and cleaning stays diagram refer to installation instructions AB 544. 30 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
Information on the product Application diagram Hinge side K Tilt&Turn hardware for comfort windows Application diagram Hinge side K Tilt&Turn hardware for comfort windows Limitation of sash formats depending on the glass thickness 50 kg/m 2 40 kg/m 2 30 kg/m 2 20 kg/m 2 Application range Sash rebate width SRW...520 1400 mm Sash rebate height SRH...530 1600 mm Sash weight S.kg...max. 50 kg The information in the application diagram refers to the glass weight in kg/m 2. SRH in mm 1500 1000 1 mm/m 2 glass thickness = 2.5 kg 1000 SRW in mm = Impermissible application range Subject to change. Roto NT IMO_63_EN_v3 January 2017 31
32 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
1 T&T espagnolette, fixed handle height, backset 15 mm 6) SRH / mm Handle height / Espagnolette length / Material no. mm mm 3) 120 370 2843142)8) 2 T&T espagnolette, centred/variable handle height, backset 15 mm 6) SRH / mm Handle height / Espagnolette length / Material no. mm mm 3) 155 225 430 2597172) 4) 225 310 400 2597182) SRW / mm Description Length Material no. 10 Stay arm K, system 12 / 20-13 10) SRW / mm Size Material no. SRW / mm SRH / mm Size Material no. 1) Use an additional scissor stay from SRW 1400 mm 9 2) Not possible in combination with a lifting mishandling device 3) With special corner drive 7 4) With corner drive 5 5) On SRW < 310 mm assembly clip must be removed 6) Backset 8 mm, refer to the CTL_7 catalogue 7) Maximum tilt-depth 80 mm 8) With integrated corner drive 1 9) From SRH 2401 mm: centre lock CL 200 CON 3 10) Additional systems can be found from page 68 Hardware overview Explanation on the hardware overview chapter The hardware overviews on the following pages are recommendations of Roto Frank AG. The hardware overview chapter shows on the left page the single hardware components in the hardware overview and on the right page the respective parts list. Position numbers in surrounding circles allow the allocation between hardware overview and parts list. Hardware overview Tilt&Turn hardware Basic security Hardware overview Hardware overview Tilt&Turn hardware Basic security Parts list Application range Sash rebate width SRW...290 1600 mm 1) Sash rebate height SRH...280 2600 mm 9) Sash weight S.kg... max. 100 resp. 130 kg 22 19 9 21 10 11a 11 280 360 3 5 8 12 7 19 361 480 4) 481 600 170 490 259830 601 800 263 690 1 E 259833 801 1000 413 890 1 E 259836 1001 1200 513 1090 1 E 259838 1201 1400 563 1290 1 E 259840 1401 1600 563 1490 2 E 259843 1601 1800 563 1690 2 E 259846 1601 1800 1000 1690 2 E 259847 1801 2000 1000 1890 2 E 259849 2001 2200 1000 2090 3 E 259852 2201 2400 1000 2290 3 E 259855 9) 2401 2600 1000 2290 3 E 259855 11 Stay bearing K 3 / 100 230177 Stay bearing K 6 / 100 not dep. 230178 Stay bearing K 6 / 130 not dep. L 230179 R 230180 11a Stay-bearing pin 227354 12 Stay corner drive 1 P 260286 13 Multipart centre lock, horizontal and vertical 801 1200 801 1200 400 1 E 255280 1201 1400 1201 1400 600 1 E 255281 1401 1600 1401 1800 600 CON 1 E 255282 400 1 E 255280 1801 2000 600 CON 1 E 255282 600 1 E 255281 2001 2400 600 CON 1 E 255282 600 CON 1 E 255282 19 1 2 20 4 13 17 16 310 450 451 620 621 800 311 400 580 1 E 259719 801 1200 401 600 980 1 E 259720 1201 1600 601 800 1380 2 E 259721 1601 2000 801 1000 1780 2 E 259762 2001 2400 1001 1200 2180 4 E 259763 9) 2401 2600 1001 1200 2180 4 E 259763 3 Centre lock 200 CON (from SRH 2401 mm) 308267 4 Bullet catch cam 256020 5 Corner drive not dep. 1 E 260275 Corner drive 1 P 260277 6 Corner drive, T&T 1 P 260290 400 1 E 255280 2401 2600 600 CON 1 E 255282 600 CON 1 E 255282 600 1 E 255281 14 Corner hinge K 3 / 100 230343 Corner hinge K 6 / 130 not dep. 263858 15 Pivot rest K 3 / 100 258590 Pivot rest K 6 / 100 not dep. 258592 Pivot rest K 6 / 130 not dep. L 230354 R 230355 16 Lifting mishandling device, sash component 260538 Profile-related components: tables from p. 72 17 Lifting mishandling device, frame component 18 Tilt striker 19 Striker 19 7 Special corner drive not dep. 1 E 260280 (SRH < 360 mm) Special corner drive 1 P 260282 (SRH < 360 mm) 20 Bullet catch (from SRH 1601 mm) 21 Packers for additional scissor stay 22 Night-vent, as an option 6 5 14 13 15 8 Stay guide 290 410 150 300 260201 5) 411 600 250 490 256024 601 800 350 690 260204 801 1000 500 890 1 E 260208 1001 1200 500 1090 1 E 260212 1) 1201 1400 500 1290 1 E 260215 9 Additional scissor stay (from SRW 1400 mm) 255237 Additional scissor stay TF (from SRW 1400 mm) not dep. 292022 18 On SRH < 500 mm, the tilt-depth must be limited to 80 mm! 19 7) 290 410 150 L 258060 R 258061 411 600 250 L 258062 R 258063 601 800 350 L 258064 R 258065 801 1600 500 L 258042 R 258043 34 January 2017 IMO_63_EN_v3 Roto NT Subject to change. Subject to change. Roto NT IMO_63_EN_v3 January 2017 35 The actual scope of delivery depends on the ordered hardware configuration (height and width of the window). Subject to change. Roto NT IMO_63_EN_v3 January 2017 33
Hardware overview Tilt&Turn hardware Basic security Hardware overview 22 19 21 10 11a 11 9 8 3 5 12 7 19 19 1 2 20 4 13 17 16 19 5 14 15 6 13 18 19 On SRH < 500 mm, the tilt-depth must be limited to 80 mm! 34 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
Hardware overview Tilt&Turn hardware Basic security Parts list Application range Sash rebate width SRW...290 1600 mm 1) Sash rebate height SRH...280 2600 mm 9) Sash weight S.kg... max. 100 resp. 130 kg 1 T&T espagnolette, fixed handle height, backset 15 mm 6) SRH / mm Handle height / mm Espagnolette Material no. length / mm 280 360 3) 120 370 284314 2)8) 361 480 4) 481 600 170 490 259830 601 800 263 690 1 E 259833 801 1000 413 890 1 E 259836 1001 1200 513 1090 1 E 259838 1201 1400 563 1290 1 E 259840 1401 1600 563 1490 2 E 259843 1601 1800 563 1690 2 E 259846 1601 1800 1000 1690 2 E 259847 1801 2000 1000 1890 2 E 259849 2001 2200 1000 2090 3 E 259852 2201 2400 1000 2290 3 E 259855 2401 2600 9) 1000 2290 3 E 259855 2 T&T espagnolette, centred/variable handle height, backset 15 mm 6) SRH / mm Handle height / mm Espagnolette length / mm Material no. 310 450 3) 155 225 430 259717 2) 451 620 4) 225 310 400 259718 2) 621 800 311 400 580 1 E 259719 801 1200 401 600 980 1 E 259720 1201 1600 601 800 1380 2 E 259721 1601 2000 801 1000 1780 2 E 259762 2001 2400 1001 1200 2180 4 E 259763 2401 2600 9) 1001 1200 2180 4 E 259763 3 Centre lock 200 CON (from SRH 2401 mm) 308267 4 Bullet catch cam 256020 5 Corner drive not dep. 1 E 260275 Corner drive 1 P 260277 6 Corner drive, T&T 1 P 260290 7 Special corner drive not dep. 1 E 260280 (SRH < 360 mm) Special corner drive 1 P 260282 (SRH < 360 mm) 8 Stay guide SRW / mm Description Length Material no. 290 410 150 300 260201 5) 411 600 250 490 256024 601 800 350 690 260204 801 1000 500 890 1 E 260208 1001 1200 500 1090 1 E 260212 1201 1400 1) 500 1290 1 E 260215 Stay bearing K 6 / 100 not dep. 230178 Stay bearing K 6 / 130 not dep. L 230179 R 230180 11a Stay-bearing pin 227354 12 Stay corner drive 1 P 260286 13 Multipart centre lock, horizontal and vertical SRW / mm SRH / mm Size Material no. 801 1200 801 1200 400 1 E 255280 1201 1400 1201 1400 600 1 E 255281 1401 1600 1401 1800 600 CON 1 E 255282 400 1 E 255280 1801 2000 600 CON 1 E 255282 600 1 E 255281 2001 2400 600 CON 1 E 255282 600 CON 1 E 255282 400 1 E 255280 2401 2600 600 CON 1 E 255282 600 CON 1 E 255282 600 1 E 255281 14 Corner hinge K 3 / 100 230343 Corner hinge K 6 / 130 not dep. 263858 15 Pivot rest K 3 / 100 258590 Pivot rest K 6 / 100 not dep. 258592 Pivot rest K 6 / 130 not dep. L 230354 R 230355 16 Lifting mishandling device, sash component 260538 Profile-related components: tables from p. 72 17 Lifting mishandling device, frame component 18 Tilt striker 19 Striker 20 Bullet catch (from SRH 1601 mm) 21 Packers for additional scissor stay 22 Night-vent, as an option 1) Use an additional scissor stay from SRW 1400 mm 9 2) Not possible in combination with a lifting mishandling device 3) With special corner drive 7 4) With corner drive 5 5) On SRW < 310 mm assembly clip must be removed 6) Backset 8 mm, refer to the CTL_7 catalogue 7) Maximum tilt-depth 80 mm 8) With integrated corner drive 1 9) From SRH 2401 mm: centre lock CL 200 CON 3 10) Additional systems can be found from page 68 9 Additional scissor stay (from SRW 1400 mm) 255237 Additional scissor stay TF (from SRW 1400 mm) not dep. 292022 10 Stay arm K, system 12 / 20-13 10) SRW / mm Size Material no. 290 410 150 7) L 258060 R 258061 411 600 250 L 258062 R 258063 601 800 350 L 258064 R 258065 801 1600 500 L 258042 R 258043 11 Stay bearing K 3 / 100 230177 Subject to change. Roto NT IMO_63_EN_v3 January 2017 35
Hardware overview Tilt&Turn hardware RC1 N (DIN EN 1627 1630) Hardware overview 23 21 21a 9 10a 10 8 3 5 11 20 7 21 21a 20 2 22 4 1 17 16 13 18 20 5 6 12 14 19 19a 21 21a 15 On SRH < 500 mm, the tilt-depth must be limited to 80 mm! 36 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
Hardware overview Tilt&Turn hardware RC1 N (DIN EN 1627 1630) Parts list Application range Sash rebate width SRW...320 1400 mm Sash rebate height SRH...280 2600 mm 8) Sash weight S.kg... max. 100 resp. 130 kg 1 T&T espagnolette, fixed handle height, backset 15 mm 4) 10a Stay-bearing pin 227354 SRH / mm Handle height / mm Espagnolette length / mm Material no. 11 Stay corner drive 1 P 260286 280 360 2) 120 370 284314 1)6) 361 480 3) 481 600 170 490 259830 601 800 263 690 1 E 259833 801 1000 413 890 1 E 259836 1001 1200 513 1090 1 E 259838 1201 1400 563 1290 1 E 259840 1401 1600 563 1490 2 E 259843 1601 1800 563 1690 2 E 259846 1601 1800 1000 1690 2 E 259847 1801 2000 1000 1890 2 E 259849 2001 2200 1000 2090 3 E 259852 2201 2400 1000 2290 3 E 259855 2401 2600 7) 1000 2290 3 E 259855 2 T&T espagnolette, centred/variable handle height, backset 15 mm 4) SRH / mm Handle height / mm Espagnolette length / mm Material no. 310 450 2) 155 225 430 259717 2) 451 620 3) 225 310 400 259718 2) 621 800 311 400 580 1 E 259719 801 1200 401 600 980 1 E 259720 1201 1600 601 800 1380 2 E 259721 1601 2000 801 1000 1780 2 E 259762 2001 2400 1001 1200 2180 4 E 259763 2401 2600 7) 1001 1200 2180 4 E 259763 3 Centre lock 200 CON (from SRH 2401 mm) 1 E 450821 4 Bullet catch cam 256020 5 Corner drive 1 P 260277 6 Corner drive, T&T 1 P 260290 7 Special corner drive 1 P 260282 (SRH < 360 mm) 8 Stay guide SRW / mm Description Length Material no. 320 410 150 5) 300 260201 411 600 250 490 256024 601 800 350 690 260204 801 1000 500 890 1 E 260208 1001 1200 500 1090 1 E 260212 1201 1400 500 1290 1 E 260215 9 Stay arm K, system 12 / 20-13 8) SRW / mm Size Material no. 320 410 150 5) L 258060 R 258061 411 600 250 L 258062 R 258063 601 800 350 L 258064 R 258065 801 1400 500 L 258042 R 258043 10 Stay bearing K 3 / 100 230177 Stay bearing K 6 / 100 not dep. 230178 Stay bearing K 6 / 130 not dep. L 230179 R 230180 12 Multipart centre lock, horizontal SRW / mm Size Material no. 320 520 200 1 P 255284 521 730 400 1 P 255285 731 930 600 1 P 255286 931 1130 600 CON 1 E 255282 200 1 P 255284 1131 1330 600 CON 1 E 255282 400 1 P 255285 1331 1400 600 CON 1 E 255282 600 1 P 255286 13 Multipart centre lock, vertical SRH / mm Size Material no. 801 1200 400 1 E 255280 1201 1400 600 1 E 255281 1401 1800 600 CON 1 E 255282 400 1 E 255280 1801 2000 600 CON 1 E 255282 600 1 E 255281 2001 2400 600 CON 1 E 255282 600 CON 1 E 255282 400 1 E 255280 2401 2600 600 CON 1 E 255282 600 CON 1 E 255282 600 1 E 255281 14 Corner hinge K 3 / 100 230343 Corner hinge K 6 / 130 not dep. 263858 15 Pivot rest K 3 / 100 258590 Pivot rest K 6 / 100 not dep. 258592 Pivot rest K 6 / 130 not dep. L 230354 R 230355 16 Lifting mishandling device, sash component 260538 17 Drilling protection 627343 Profile-related components: tables from p. 72 18 Lifting mishandling device, frame component 19 Tilt striker (13 mm hardware axis) 19a Tilt striker, steel (9 mm hardware axis) 20 Striker 21 Security striker (13 mm hardware axis) 21a Security striker, steel (9 mm hardware axis) 22 Bullet catch (from SRH 1601 mm) 23 Night-vent, as an option 1) Not possible in combination with a lifting mishandling device 2) With special corner drive 7 3) With corner drive 5 4) Backset 8 mm, refer to the CTL_7 catalogue 5) Maximum tilt-depth 80 mm 6) With integrated corner drive 1 7) From SRH 2401 mm: centre lock CL 200 CON 3 8) Additional systems can be found from page 68 Subject to change. Roto NT IMO_63_EN_v3 January 2017 37
Hardware overview Tilt&Turn hardware RC2 / RC2 N (DIN EN 1627 1630) Hardware overview 20 18 18 8 9a 9 7 4 10 18 1 2 18 15 19 3 11 18 14 16 11 18 6 18 4 5 12 11 17 18 13 On SRH < 500 mm, the tilt-depth must be limited to 80 mm! 38 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
Hardware overview Tilt&Turn hardware RC2 / RC2 N (DIN EN 1627 1630) Parts list Application range Sash rebate width SRW...320 1400 mm Sash rebate height SRH...490 2400 mm Sash weight S.kg... max. 100 resp. 130 kg 1 T&T espagnolette, fixed handle height, backset 15 mm 1) SRH / mm Handle height / mm Espagnolette Material no. length / mm 490 600 170 490 259830 601 800 263 690 1 V 259832 801 1000 413 890 2 V 259835 1001 1200 513 1090 2 V 259837 1201 1400 563 1290 2 V 259839 1401 1600 563 1490 3 V 259841 1601 1800 563 1690 3 V 259844 1601 1800 1000 1690 3 V 259845 1801 2000 1000 1890 3 V 259848 2001 2200 1000 2090 4 V 259850 2201 2400 1000 2290 4 V 259853 2 T&T espagnolette, centred/variable handle height, backset 15 mm 1) SRH / mm Handle height / mm Espagnolette length / mm Material no. 490 620 2) 245 310 400 259718 2)3) 621 800 3) 311 400 580 1 V 355743 801 1200 401 600 980 1 V 355744 1201 1600 601 800 1380 2 V 355745 1601 2000 801 1000 1780 2 V 355746 2001 2400 1001 1200 2180 4 V 355747 3 Bullet catch cam 256020 4 Corner drive 1 V 260272 5 Corner drive, T&T 1 V 260288 6 Corner drive RC3 2 V 260274 7 Security stay guide SRW / mm Description Length Material no. 290 410 150 300 260201 411 600 250 490 256024 601 800 350 690 260204 801 1000 500 890 1 V 260206 1001 1200 500 1090 1 V 260210 1201 1400 500 1290 1 V 260213 8 Stay arm K, system 12 / 20-13 5) SRW / mm Size Material no. 320 410 150 4) L 258060 R 258061 411 600 250 L 258062 R 258063 601 800 350 L 258064 R 258065 801 1400 500 L 258042 R 258043 9 Stay bearing K 3 / 100 230177 Stay bearing K 6 / 100 not dep. 230178 Stay bearing K 6 / 130 not dep. L 230179 R 230180 9a Stay-bearing pin 227354 10 Stay corner drive 1 V 260284 11 Multipart centre lock, horizontal and vertical SRW / mm SRH / mm Size Material no. 320 600 490 700 200 1 V 296853 601 800 701 900 400 1 V 296854 801 1000 901 1100 600 1 V 296855 1001 1200 1101 1300 600 CON 1 V 337711 200 1 V 296853 1201 1400 1301 1500 600 CON 1 V 337711 400 1 V 296854 1501 1700 600 CON 1 V 337711 600 1 V 296855 1701 1900 600 CON 1 V 337711 600 CON 1 V 337711 200 1 V 296853 1901 2100 600 CON 1 V 337711 600 CON 1 V 337711 400 1 V 296854 2101 2300 600 CON 1 V 337711 600 CON 1 V 337711 600 1 V 296855 2301 2400 600 CON 1 V 337711 600 CON 1 V 337711 600 CON 1 V 337711 200 1 V 296853 12 Corner hinge K 3 / 100 230343 Corner hinge K 6 / 130 not dep. 263858 13 Pivot rest K 3 / 100 258590 Pivot rest K 6 / 100 not dep. 258592 Pivot rest K 6 / 130 not dep. L 230354 R 230355 14 Lifting mishandling device, sash component 260538 15 Drilling protection 627343 Profile-related components: tables from p. 72 16 Lifting mishandling device, frame component 17 Tilt striker 18 Security striker 19 Bullet catch (from SRH 1601 mm) 20 Night-vent, as an option 1) Backset 8 mm, refer to the CTL_7 catalogue 2) Not possible in combination with a lifting mishandling device 3) With corner drive RC3 6 bottom 4) Maximum tilt-depth 80 mm 5) Additional systems can be found from page 68 Subject to change. Roto NT IMO_63_EN_v3 January 2017 39
Hardware overview Tilt&Turn hardware Comfort Basic security Hardware overview 14 14 4 6 5 8 2 7 14 14 14 12 12 14 14 16 3 11 1 9 8 10 15 13 14 40 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
Hardware overview Tilt&Turn hardware Comfort Basic security Parts list Application range Sash rebate width SRW...520 1400 mm Sash rebate height SRH...530 1600 mm Sash weight S.kg...max. 50 kg 1 T&T espagnolette Comfort fixed handle height, backset 15 mm SRW / mm Espagnolette Material no. length / mm 520 700 490 307029 701 1400 1) 690 1 E 307030 2 Corner drive 1 P 260277 3 Corner drive, T&T 1 P 260290 4 Stay arm K, positive control, system 12 / 20-9 SRW / mm Size Material no. 520 600 490 L 477459 R 477458 601 800 690 L 477461 R 477460 801 1400 2) 890 1 E L 477463 1 E R 477462 Stay arm K, positive control, system 12 / 20-13 SRW / mm Size Material no. 520 600 490 L 307032 R 307031 601 800 690 L 307034 R 307033 801 1400 2) 890 1 E L 307036 1 E R 307035 11 Arched corner drive 255273 12 Arched component, vertical SRH / mm SRH / mm hinge side Material no. 530 600 245715 530 730 601 800 1 E 245717 731 930 801 1000 1 E 245719 931 1130 1001 1200 1 E 245721 1131 1330 1201 1400 2 E 245723 1331 1530 1401 1600 2 E 245725 1531 1600 2 E 245727 13 Run-up block with mishandling device 307050 Profile-related components: tables from p. 72 14 Striker 15 Tilt striker Optional parts: CTL_1 16 Roto Line Patio S 1) From SRW 901 mm with espagnolette extension 2) From SRW 1001 mm with espagnolette extension 5 Stay bearing K 3 / 100 230177 Stay bearing K 6 / 100 not dep. 230178 6 Stay-bearing pin 227354 7 Stay corner drive 1 P 260286 8 Espagnolette extension, horizontal SRW / mm bottom SRW / mm top Size Material no. 901 1100 1001 1200 200 308267 1101 1300 1201 1400 400 1 E 260193 1301 1400 200 308267 400 1 E 260193 9 Corner hinge K 3 / 100 230343 Corner hinge K 6 / 130 not dep. 263858 10 Pivot rest K 3 / 100 258590 Pivot rest K 6 / 100 not dep. 258592 Subject to change. Roto NT IMO_63_EN_v3 January 2017 41
Hardware overview Turn-Only hardware Basic security Hardware overview 20 20 11a 11 10 8 3 5 9 7 2 20 21 1 17 18 4 12 16 5 6 13 8 15 19 20 14 42 January 2017 IMO_63_EN_v3 Roto NT Subject to change.
Hardware overview Turn-Only hardware Basic security Parts list Application range Sash rebate width SRW...290 1600 mm Sash rebate height SRH...280 2600 mm 5) Sash weight S.kg... max. 100 resp. 130 kg 1 T&T espagnolette, fixed handle height, backset 15 mm 4) SRH / mm Handle height / mm Espagnolette Material no. length / mm 280 360 2) 120 370 284314 1)6) 361 480 3) 481 600 170 490 259830 601 800 263 690 1 E 259833 801 1000 413 890 1 E 259836 1001 1200 513 1090 1 E 259838 1201 1400 563 1290 1 E 259840 1401 1600 563 1490 2 E 259843 1601 1800 563 1690 2 E 259846 1601 1800 1000 1690 2 E 259847 1801 2000 1000 1890 2 E 259849 2001 2200 1000 2090 3 E 259852 2201 2400 1000 2290 3 E 259855 2401 2600 5) 1000 2090 3 E 259855 2 T&T espagnolette, centred/variable handle height, backset 15 mm 4) 11 Stay bearing K 3 / 100 230177 Stay bearing K 6 / 100 not dep. 230178 Stay bearing K 6 / 130 not dep. L 230179 R 230180 11a Stay-bearing pin 227354 12 Lifting mishandling device, sash component 260538 13 Corner hinge K 3 / 100 230343 Corner hinge K 6 / 130 not dep. 263858 14 Pivot rest K 3 / 100 258590 Pivot rest K 6 / 100 not dep. 258592 Pivot rest K 6 / 130 not dep. L 230354 R 230355 15 Travel restrictor (90 ) 264603 Profile-related components: tables from p. 72 16 Lifting mishandling device, frame component SRH / mm Handle height / mm Espagnolette length / mm Material no. 17 Centre-closer, concealed, sash component 310 450 2) 155 225 430 259717 1) 451 620 3) 225 310 400 259718 1) 621 800 311 400 580 1 E 259719 801 1200 401 600 980 1 E 259720 1201 1600 601 800 1380 2 E 259721 1601 2000 801 1000 1780 2 E 259762 2001 2400 1001 1200 2180 4 E 259763 2401 2600 5) 1001 1200 2180 4 E 259763 3 Centre lock 200 CON (from SRH 2401 mm) 308267 4 Bullet catch cam 256020 18 Centre-closer, concealed, frame component 7) 19 Security striker 20 Striker 21 Bullet catch 1) Not possible in combination with a lifting mishandling device 2) With special corner drive 7 3) With corner drive 5 4) Backset 8 mm, refer to the CTL_7 catalogue 5) From SRH 2401 mm: centre lock CL 200 CON 3 6) With integrated corner drive 1 7) Observe the installation advice on page 100 101 5 Corner drive not dep. 1 E 260275 Corner drive 1 P 260277 6 Corner drive, T&T 1 P 260290 7 Special corner drive not dep. 1 E 260280 (SRH < 360 mm) Special corner drive 1 P 260282 (SRH < 360 mm) 8 Multipart centre lock, horizontal SRW / mm Size Material no. 801 1200 400 1 E 255280 1201 1400 600 1 E 255281 1401 1600 600 CON 1 E 255282 400 1 E 255280 9 Sash-component for rebate hinge 331488 10 Rebate-hinge arm K 12/18-9 L 264081 R 264083 Rebate-hinge arm K 12/20-9 L 263183 R 263184 Rebate-hinge arm K 12/20-13 L 230639 R 230640 Subject to change. Roto NT IMO_63_EN_v3 January 2017 43