Parts Manual for MID-SIZE WALK BEHIND MOWERS SERIES 0 & 1 POWER UNIT MODELS SPE1250KW SPE131KW SPE140KW SPE150KH SPE151KW SPEL150KH MOWER MODELS SPE360 SPE361 SPE481 McDonough, GA, 30253 U.S.A. COPYRIGHT 2005 SNAPPER PRODUCTS, INC. ALL RIGHTS RESERVED. Revision 6, 10/21/2005
Table Of Contents PAGE GROUP 4 PISTOL GRIP HANDLE & CONTROL ASSEMBLIES 8 LOOP HANDLE & CONTROLS (Traction) 10 LOOP HANDLE & CONTROLS (Shift Lever) 12 FUEL TANK & BRACKET ASSEMBLY 14 TRANSMISSION DRIVE GROUP 16 REAR DECK, DRIVE IDLER & BRAKE ASSEMBLIES 20 TRACTION, REAR WHEEL ASSEMBLY 22 BRAKE ASSEMBLY 24 LEFT & RIGHT IDLER PULLEY ASSEMBLIES 26 ENGINE GROUP 30 CASTER, WHEEL & TIRE ASSEMBLY 32 36" MOWER DECK ASSEMBLY 36 36" DECK IDLER ASSEMBLY 38 48" MOWER DECK ASSEMBLY 40 48" DECK IDLER ASSEMBLY 42 CUTTER HOUSING ASSEMBLY 44 DECALS (Pt. 1) 46 DECALS (Pt. 2) 48 ELECTRICAL COMPONENTS (Pistol Grip Handle) 50 ELECTRICAL COMPONENTS (Loop Handle) 52 WIRING SCHEMATIC (Pistol Grip Handle) 54 WIRING SCHEMATIC (Loop Handle) SERIES 0 & 1 3
PISTOL GRIP HANDLE & CONTROL ASSEMBLIES 4 SERIES 0 & 1
PISTOL GRIP HANDLE & CONTROL ASSEMBLIES Item Part No Qty Description Note 1 7012363 2 CLEVIS PIN (all models except SPEL150KH) 2 7073573 2 ROD, Brake (3/8-16 thread) 3 7073836 2 ROD, Traction (3/8-16 thread) 4 7046181 2 WELDMENT, Drive Lever (Pistol Grip) 5 7034162 2 COTTER PIN, 5/16 Self Lock 6 7091309 2 CLEVIS PIN, 3/16 x 1-3/4 7 7090307 2 SCREW, #10-24 x 1/2 Hex Washer Self-Tap 8A 7046400 1 SPRING, Torsion, LH, Drive Lever 8B 7046399 1 SPRING, Torsion, RH, Drive Lever 9 7046235 2 LATCH, Express 10 7041880 1 BRACKET, Shift Handle 11 7024571 2 GRIP, Latch 12A 7045189 1 WELDMENT, Traction Link, Upper LH 12B 7045197 1 WELDMENT, Traction Link, Upper RH 13 7024586 2 SWIVEL, Brake Link- PM 14 7091594 8 COTTER PIN, 1/2 Self-Locking 15 7024607 1 SWIVEL, Brake Link- PM 16 7028036 3 SPRING, Friction Pack 17 7090122 9 WASHER, 3/8 SAE Flat 18 7091299 9 NUT, 3/8-16 Hex Nyloc 19 7024127 2 GRIP, Vinyl.937 x 4-1/2 20 7041878 1 WELDMENT, Pistol Grip Handle 21 7023354 2 SWITCH, Seat (Normally Closed) replaces p/n 17590 22A 7045158 1 WELDMENT, Traction Link, Lower, RH 22B 7045157 1 WELDMENT, Traction Link, Lower, LH 23 7041874 2 SWIVEL, 3/8-16 Internal Thread 24 7012686 1 NUT, 1/2-27 Hex (Special) 25 7029715 1 SWITCH, Toggle (Indak H671A) 26 7012685 1 NUT, 5/8-32 Hex (Ignition Switch) 27 7090880 1 WASHER, 5/8 Internal Tooth Lock 28 7017817 1 SWITCH, Ignition, 2-Pole, Recoil Start 29 7032692 1 WASHER, Nylon (Wear Spacer) 30 7072383 1 LEVER, Shift 31 7026420 1 GRIP, Flat Bar (Black) 32 7046418 2 GRIP, 3/4 ID x 4 Textured 33 7091497 1 SCREW, 3/8-16 x 1-1/2 Hex Head Cap, GR 5 34 7041883 1 SHIFT ROD, Express (3/8-16 thread) Footnotes: NOTE 1: Part Number & revision stamped on part SERIES 0 & 1 5
PISTOL GRIP HANDLE & CONTROL ASSEMBLIES 6 SERIES 0 & 1
PISTOL GRIP HANDLE & CONTROL ASSEMBLIES Item Part No Qty Description Note 35 7045195 1 WIRING HARNESS, Pistol Grip see also Pistol Grip Electrical Components page. 36 7091640 6 BOLT, 3/8-16 x 1 Square Neck Carriage, GR 5 37 7075484 1 CONTROL, Throttle, 42/.88 (Kawasaki) Capro 65-0519-06; replaces 22354; see Footnote 1 38 7091317 2 SCREW, 1/4-20 x 3 Hex Head Cap, GR 5 39 7090055 2 WASHER, 1/4 Flat 40 7029125 2 SPACER, Brake (Outer) 41 7023313 2 ROLL PIN, 5/16 42 7024129 2 SPACER, Brake 43 7091603 2 NUT, 1/4-20 Hex Nyloc 44A 7041660 1 GRIP, Pistol OPC (RH) (Weldment) 44B 7041659 1 GRIP, Pistol OPC (LH) (Weldment) 45 7011138 1 KEY, Ignition (Pair) Footnotes: NOTE 1: Part Number & revision stamped on part SERIES 0 & 1 7
LOOP HANDLE & CONTROLS (Traction) 8 SERIES 0 & 1
LOOP HANDLE & CONTROLS (Traction) Item Part No Qty Description Note 1 7058842 1 LOOP HANDLE, Express (Weldment) 2 7027225 1 SWITCH, OPC (NC) 3 7077873 2 SCREW, #12-14 x 1/2 Hex Flange Self-Tap 4 7022166 1 ROD, Pivot 5 7091030 5 BUSHING, 1/2 Machine 6 7014341 2 E-RING, 1/2 7 7058847 1 LEVER, Traction RH (Weldment) 8 7058848 1 LEVER, Traction LH (Weldment) 9 7073311 2 PLATE, Neutral Latch 10 7073315 2 SPACER, Neutral Latch 11 7034803 2 PIN, Shoulder 12 7059115 1 LATCH, Neutral (Weldment) 13 7012080 4 CABLE TIE, 7 not shown 14 7011879 1 VINYL GRIP,.313 Dia. x 3-3/4 long 15 7028857 4 BEARING 16 7041748 1 BAIL, Operator Presence Control (Weldment) 17 7091003 2 BOLT, 1/4-20 x 1-3/4 Hex Head Cap, GR 5 18 7074648 1 ROD, Operator Presence Control 19 7029139 1 SPRING, OPC 20 7073309 1 PANEL, Console LH 21 7091122 5 SCREW, 1/4-20 x 1/2 Hex Washer Self-Tap 22 7091686 1 SCREW, 1/4-20 x 3/4 Hex Washer Self-Tap 23 7029715 1 SWITCH, Toggle (Indak H671A) 24 7012686 1 NUT, 1/2-27 (Special) 25 7029100 1 THROTTLE CONTROL (Kohler) Capro p/n 65-0808; not shown 26 7076998 2 GREASE FITTING (1/2-28 thread) 27 7090977 2 NUT, 1/4-20 Hex Jam 28 7027220 1 SCREW, 3/8-16 x 3-1/4 Hex Head Cap, GR 5 29 7091299 1 NUT, 3/8-16 Hex Nyloc Footnotes: (Model SPEL150KH only) SERIES 0 & 1 9
LOOP HANDLE & CONTROLS (Shift Lever) 10 SERIES 0 & 1
LOOP HANDLE & CONTROLS (Shift Lever) Item Part No Qty Description Note 1 7091122 5 SCREW, 1/4-20 x 1/2 Hex Washer Self-Tap also shown on previous page 2 7091686 1 SCREW, 1/4-20 x 3/4 Hex Washer Self-Tap also shown on previous page 3 7091299 8 NUT, 3/8-16 Hex Nyloc also shown on previous page 4 7073310 1 PANEL, Console RH 5 7017817 1 SWITCH, On-Off 6 7090880 1 WASHER, 5/8 Internal Tooth Lock 7 7012685 1 NUT, 5/8-32 Hex (Special) 8 7011138 1 KEY, Ignition (Pair) 9 7041880 1 BRACKET, Shift Handle 10 7091640 6 BOLT, 3/8-16 x 1 Square Neck Carriage, GR 5 11 7091497 1 SCREW, 3/8-16 x 1-1/2 Hex Head Cap, GR 5 12 7032692 1 SPACER, Wear 13 7072383 1 SHIFT LEVER 14 7028036 3 SPRING, Friction Pack 15 7090122 5 WASHER, 3/8 SAE Flat 16 7026420 1 GRIP, Flat Bar (Black) 17 7073314 1 ROD, Shift (21-1/2 long, 3/8-16 thread) 18 7091594 10 COTTER PIN, 1/2 Self-Locking 19 7024607 1 SWIVEL, Brake Link, 3/8-16 thread.019 Dia. Hole (PM) 20 7091296 6 WASHER, 5/16 Flat 21 7073953 2 PIN, 5/16 x.94 Clevis 22 7073312 2 ROD, Traction (22 Long, 3/8-16 Thread) 23 7041874 2 SWIVEL, 3/8-16 Thread,.109 Dia. Hole 24 7058929 1 TRACTION LINK, Lower Left (Weldment) 25 7058930 1 TRACTION LINK, Lower Right (Weldment) 26 7058931 1 TRACTION LINK, Upper Right (Weldment) 27 7058932 1 TRACTION LINK, Upper Left (Weldment) 28 7073317 1 WIRING HARNESS, Loop Handle (not shown) See Loop Handle Electrical Components page. 29 7024586 2 SWIVEL,.406 &.109 Dia. Holes 30 7073313 2 ROD, Brake (37-3/4 Long, 3/8-16 Thread) 31 7034162 2 COTTER PIN, 5/16 Self Lock Footnotes: (Model SPEL150KH only) SERIES 0 & 1 11
FUEL TANK & BRACKET ASSEMBLY 12 SERIES 0 & 1
FUEL TANK & BRACKET ASSEMBLY Item Part No Qty Description Note -- 7054630 1 TANK BRACKET GROUP (Incl. Items 1A, 1B & 3 thru 17) -- 7059021 1 TANK BRACKET GROUP (Incl. 1B, 2B & 3-20) used on Model SPEL150KH only 1A 7073741 1 TANK BRACKET, Express 1B 7073732 1 TANK BRACKET, Express (Loop handle) not shown 2A 7044639 1 TANK, Fuel (with cap) 2B 7028903 1 CAP, Fuel Tank 3 7034923 2 STRAP, Tank 4 7091207 2 SCREW, #10-24 x 2-1/2 Pan Head Machine 5 7091290 2 NUT, #10-24 Hex Nyloc 6 7059496 1 ASSEMBLY, Shift Bellcrank, Express (Includes 3 Items listed below) -- 7041881 1 WELDMENT, Shift Bellcrank -- 7013864 1 FITTING, 3/16 Lube -- 7014409 2 BEARING, 9/16 Flange 7 7091221 1 BOLT, 3/8-16 x 2.44 Shoulder 8 7091804 2 WASHER, 9/16 Flat (Narrow Type) 9 7059495 1 ASSEMBLY, Shift Link, Express (Incl. Items 10 thru 12) 10 7015753 2 BALL JOINT 11 7035908 1 ROD, 1/4-28 x 2.71 Threaded 12 7091605 3 NUT, 1/4-28 Hex, GR 5 or B or 90095 13 7090052 1 WASHER, 1/4 Split Lock 14 7091812 1 NUT, 1/4-28 Hex Nyloc 15 7091585 1 NUT, 3/8-16 Hex Center lock 16 7091640 6 BOLT, 3/8-16 x 1 Short Neck Carriage, GR 5 17 7091299 6 NUT, 3/8-16 Hex Nyloc 18 7073958 1 TANK BRACKET, Upper 19 7091303 3 BOLT, 5/16-18 x 1 Short Neck Carriage, GR 5 20 7091298 3 NUT, 5/16-18 Hex Nyloc Footnotes: SERIES 0 & 1 13
TRANSMISSION DRIVE GROUP 14 SERIES 0 & 1
TRANSMISSION DRIVE GROUP Item Part No Qty Description Note 1 7012705 2 RING, 3/4 External Retaining Truarc p/n 5133-75 2 7010935 6 WASHER, 3/4 x 1-1/8 x.06 Flat 3 7041908 2 PULLEY, Trans Output, 5.5 Dia., 2RA 4 7046240 2 BELT, Traction, 2RAX Sect. Eff. Length 53.4 Dayco p/n 41-0664; Neoprene Compound Polyester Cord 5 7041863 1 TORQUE BRACKET 6 7041862 1 TRANSMISSION, Peerless, 5-Speed 7 7029682 1 SWITCH, Transmission (NO) 8 7041885 1 SHIFT ARM, Express 9 7090746 2 WASHER 1/4 Bellville 10 7091165 1 BOLT, 1/4-28 x 5/8 Hex w/nyloc Patch, GR 8 11 7045191 1 PULLEY, Transmission Input 12 7010211 1 KEY, #9 Woodruff 13 7012763 1 RING, External Retaining Truarc p/n 5100-62 14 7029118 1 V-BELT, HA, Effective Length 41.650 Dayco p/n 2-1142 15 7041859 2 SUPPORT, Transmission 16 7091523 1 SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap 17 7091714 1 BOLT, 5/16-18 x 1 Square Neck Carriage, GR 5 18 7091298 5 NUT, 5/16-18 Hex Nyloc 19 7076940 4 SCREW, 5/16-18 x 4-1/2 Hex Head Cap, GR 5 20 7041868 4 SPACER, Transmission 21 7010061 2 KEY, 3/16 Square x 1 22 7029662 1 WASHER, Fiber 23 7011791 4 RETAINER, 5/16 Bolt Footnotes: SERIES 0 & 1 15
REAR DECK, DRIVE IDLER & BRAKE ASSEMBLIES 16 SERIES 0 & 1
REAR DECK, DRIVE IDLER & BRAKE ASSEMBLIES Item Part No Qty Description Note 1 7091600 4 NUT, 3/8-24 Hex Nyloc 2 7073837 4 STUD, Shoulder (3/8-24 thread w/snap-ring Groove) 3A 7054635 1 IDLER ASSY, Upper Left (see Footnote 1) all models except SPEL150KH 3B 7058935 1 IDLER ASSY, Upper Left Model SPEL150KH only 3C 7054636 1 IDLER ASSY, Lower Left all models 4A 7054637 1 IDLER ASSY, Upper Right all models except SPEL150KH 4B 7058936 1 IDLER ASSY, Upper Right Model SPEL150KH only 4C 7054639 1 IDLER ASSY, Lower Right all models 5 7091299 4 NUT, 3/8-16 Hex Nyloc 6 7091040 -- RETAINER, 5/8 Bolt not shown; replaced by item 29 7 7046499 2 SPRING, Extension 8 7058934 1 FRAME, Engine (Weldment) 9 7091640 2 BOLT, 3/8-16 x 1 Square Neck Carriage, GR 5 10 7028046 1 BRACKET, Anti-Spin replaces 7046228 11 7091298 4 NUT, 5/16-18 Hex Nyloc 12 7054631 1 ASSEMBLY, Brake Band, RH all models except SPE131KW 12 7074810 1 ASSEMBLY, Brake Band, 6 Thomas Model SPE131KW only 13 7027197 1 SPRING, Extension 14 7059494 1 ASSEMBLY, Idler Arm 15 7091323 6 BOLT, 1/2-13 x 1-1/4 Hex Flange Lock, GR 5 16 7091804 2 WASHER, 9/16 Flat (Narrow Type) 17 7091221 1 SHOULDER BOLT, 3/8-16 x 2-7/16 18 7041869 2 SCRAPER, Wheel Pulley 19 7016561 6 BUSHING, 1 x 14 Ga Machine 20 7054640 2 ASSEMBLY, Wheel/Drum/Pulley 21 7012730 2 E RING, Retaining Truarc p/n X5133-98 22 7091305 2 SCREW, 3/8-16 x 2 Hex Head Cap, GR 5 23 7091303 4 BOLT, 5/16-18 x 1 Short Neck Carriage, GR 5 24 7091043 10 BUSHING, Machine, 5/8 25 7091302 2 NUT, 3/8-16 Hex, GR 5 or B 26 7054632 1 ASSEMBLY, Brake Band, LH all models except SPE131KW -- 7074810 1 ASSEMBLY, Brake Band, 6 Thomas Model SPE131KW only 27 7058933 2 WELDMENT, Brake Stud 28 7073594 1 DECAL, Caution see Decal page 29 7010739 4 RING, 5/8 External Retaining Truarc p/n 5160-62 30 7022768 4 STUD, Fender Mount (3/8-16 thread, both ends) 31A 7046225 2 BELT COVER, Express all models except SPE131KW Footnotes: NOTE 1: For components see L & R Idler Pulley Assembly page. SERIES 0 & 1 17
REAR DECK, DRIVE IDLER & BRAKE ASSEMBLIES 18 SERIES 0 & 1
REAR DECK, DRIVE IDLER & BRAKE ASSEMBLIES Item Part No Qty Description Note 31B 7073510 2 BELT COVER, Express Model SPEL150KH only 32 7091322 6 WASHER, 1/2 Split Lock 33 7091049 4 WINGNUT, 3/8-16 w/nylon Ring 34 7091585 2 NUT, 3/8-16 Hex Center Lock 35 7091316 6 NUT, 1/2-13 Hex, GR B 36 7090990 1 BOLT, 3/8-16 x 2 Short Neck Carriage, GR 5 37 7041873 1 WELDMENT, Idler Arm, Express 38 7013864 3 LUBE FITTING, 3/16 Press-In 39 7014409 2 FLANGE BEARING, 9/16 I.D. 40 7018573 1 IDLER, V-Belt, 3.56 O.D. Footnotes: NOTE 1: For components see L & R Idler Pulley Assembly page. SERIES 0 & 1 19
TRACTION, REAR WHEEL ASSEMBLY 20 SERIES 0 & 1
TRACTION, REAR WHEEL ASSEMBLY Item Part No Qty Description Note 1 7059983 2 ASSEMBLY, Tire & Hub (Includes Items 2 thru 6) 1 7100129 2 ASSEMBLY, Tire & Hub used on SPE151KW; see Footnote 1 2 7054638 1 WELDMENT, Rim, 16 Tires 2 7044837 1 WELDMENT, Rim, Gray, Pro Express 3 7019169 2 BALL BEARING, Wheel qty 2 per rear wheel assembly 4 7027231 1 AIR VALVE, Snap-In qty 1 per rear wheel assembly 5 7076998 1 FITTING, 1/4-28 Straight Lube qty 1 per rear wheel assembly 6 7046245 1 TIRE, 16 x 6.50-8 Tubeless, Kenda 4-Ply 6 7100130 1 TIRE, 16 x 6.50-8 Turf Master 4-Ply 7 7091540 4 SCREW, 5/16-18 x 1-1/2 Hex Head Cap, GR 5 8 7017531 1 PULLEY, Traction, 8 9 7023516 1 DRUM, Brake 6 10 7023515 4 SPACER,.390 I.D. x 3/4 O. D. x.465 thick 11 7091315 4 WASHER,.32 x.58 x.08 Split Lock Footnotes: NOTE 1: 7044838 is comprised of 7100129 & items 7-11. SERIES 0 & 1 21
BRAKE ASSEMBLY 22 SERIES 0 & 1
BRAKE ASSEMBLY Item Part No Qty Description Note 1A 7044741 1 WELDMENT, Brake Arm, RH 1B 7400034 1 WELDMENT, Brake Arm, RH used on SPE151KW 1C 7044742 1 WELDMENT, Brake Arm, LH 1D 7400035 1 WELDMENT, Brake Arm, LH used on SPE151KW 2 7058933 2 WELDMENT, Brake Mount Stud 3 7040622 1 WELDMENT, Brake Link 4 7091302 2 NUT, 3/8-16 Hex, GR 5 or B 5 7074810 2 ASSEMBLY, Brake Band, 6 Thomas 6 7091305 2 SCREW, 3/8-16 x 2 Hex Head Cap, GR 5 7 7091043 2 BUSHING, 5/8 I.D. x 1 O.D. Machine 8 7013946 4 RETAINER, 3/8 Bolt 9 7032903 2 LINK, Brake 10 7091040 2 RETAINER, 5/8 Bolt 11 7013864 2 LUBE FITTING, 3/16 Press-In 12 7091299 2 NUT, 3/8-16 Hex Nyloc Footnotes: SERIES 0 & 1 23
LEFT & RIGHT IDLER PULLEY ASSEMBLIES 24 SERIES 0 & 1
LEFT & RIGHT IDLER PULLEY ASSEMBLIES Item Part No Qty Description Note 1 7054635 1 IDLER ASSY, Upper Left all models except SPEL150KH 2 7058935 1 IDLER ASSY, Upper Left Model SPEL150KH only 3 7054636 1 IDLER ASSY, Lower Left all models 4 7054637 1 IDLER ASSY, Upper Right all models except SPEL150KH 5 7058936 1 IDLER ASSY, Upper Right Model SPEL150KH only 6 7054639 1 IDLER ASSY, Lower Right all models 7 7059047 1 WELDMENT, Idler Arm, UL/LR 8 7058927 1 WELDMENT, Idler Arm Model SPEL150KH only 9 7059048 1 WELDMENT, Idler Arm, UR/LL 10 7058928 1 WELDMENT, Idler Arm Model SPEL150KH only 11 7013864 4 LUBE FITTING, 3/16 Press-In 12 7091560 4 SCREW, 3/8-16 x 2-1/4 Hex Head Cap, GR 5 13 7091320 4 WASHER,.38 x.68 x.09 Split Lock 14 7090122 4 WASHER, 3/8 SAE Flat 15 7024707 4 PULLEY- Idler 3-1/4 16 7091302 4 NUT, 3/8-16 Hex, GR 5 or B Footnotes: SERIES 0 & 1 25
ENGINE GROUP 26 SERIES 0 & 1
ENGINE GROUP Item Part No Qty Description Note 1 7015617 1 CLAMP, Fuel Hose 2 7076272 2 LINE, Fuel, 1/4 I.D. x 1/2 O.D. x 8-1/2 2 7032956 2 LINE, Fuel, 1/4 I.D. x 1/2 O.D. x 10 3 7077351 1 LINE, Fuel, 1/4 I.D. x 1/2 O.D. x 3-1/2 4 7016325 1 VALVE, Fuel 5 7014359 1 FILTER, In-Line 6 7029900 5 CLAMP, Fuel Hose or 7012222 7 7028983 1 RECTIFIER/REGULATOR, Kawasaki 8 7027215 1 CAPACITOR, Kawasaki Engine 9A 7027226 1 HARNESS, Wiring Pigtail 9B 7074852 1 HARNESS, Wiring Pigtail used on SPE131KW 10 7026978 1 BRACKET, Capacitor 11 -- 1 ENGINE, Kawasaki 12.5 HP (shown) (Mod. No. FB460V-E536) see Footnote 1 11 -- 1 ENGINE, Kawasaki 13 HP (Mod. No. FH381V-AS02) 11 -- 1 ENGINE, Kawasaki 14 HP (Mod. No. FC420V-HS09) 11 -- 1 ENGINE, Kawasaki 15 HP Express (Mod. No. FH430V-AS02) 11 -- 1 ENGINE, Kohler 15 HP (Mod. No. FH430V-AS02) 12A 7016561 1 BUSHING, 1 x 14 Ga Machine 12B 7075084 3 SPACER, Ogura Clutch 13 7045193 1 PULLEY, Engine 14 7017063 1 CLUTCH, Electric (Warner p/n 1-5215-14) 14 7072400 1 CLUTCH, Electric (Ogura p/n EXM3XR) used on SPE131KW 14 7075672 1 CLUTCH, Electric (Ogura model GT2.5 SN01) use with items 12B, 34 and 7075082 & 7017033 15 7077692 4 SCREW, M8x1.25x25 Hex Head Cap, Class 8.8 used on Kawasaki Models 15 7091540 4 SCREW, 5/16-18 x 1-1/2 Hex Head Cap, GR 5 used on Kohler Models 16 7028680 1 SCREW, M10-1.5 x 65 Hex Head Cap w/nyloc patch 16 7027266 1 SCREW, 7/16-20 x 3 Hex Head Cap Grade 5 w/nyloc patch 16 7091703 1 SCREW, 7/16-20 x 2-1/2 Hex Head Cap, GR 5 special head 16 7092071 1 SCREW, 7/16-20 x 2-1/2 Hex Head Cap, GR 5 w/nyloc patch; used on SPE151KW 17A 7091807 1 WASHER,.468 x 1.38 x.25 Flat 17B 7075082 1 SPACER, Clutch 18 7091301 1 WASHER, 7/16 Split Lock or 7090247 18 7091315 4 WASHER,.32 x.58 x.08 Split Lock 19 7091303 3 BOLT, 5/16-18 x 1 Short Neck Carriage, GR 5 20 7091298 3 NUT, 5/16-18 Hex Nyloc 21 7091814 2 SCREW, 1/4-20 x 1-1/4 Hex Head Cap 22 7091603 2 NUT, 1/4-20 Hex Nyloc Footnotes: NOTE 1: Purchase engine & engine parts, other than those listed, from engine manufacturer dealer. SERIES 0 & 1 27
ENGINE GROUP 28 SERIES 0 & 1
ENGINE GROUP Item Part No Qty Description Note 23 7091032 1 KEY, 1/4 Square x.687 23 7044751 1 KEY, 1/4 Square w/bevel 23 7074867 1 KEY, 1/4 Square x 2-1/2 used on SPE131KW 23 7017033 1 KEY, 1/4 Square x 2-1/4 24 7027972 1 OIL VALVE ASSEMBLY 25 7028513 1 WIRE, Kohler Engine Ground 26 7073011 1 SPACER, Crankshaft 27 7035411 1 BUMPER, Door (not shown) used on Kohler 15HP Model 28 7074953 1 ADAPTER, Oil Drain (not shown) (Kawasaki p/n 59071-7004) 29 7074954 1 O-RING (Kawasaki p/n 670D-2016) 30 7029704 1 BUMPER, Electric Clutch 31 7034448 1 WASHER, Rectangular Steel 32 7091527 1 SCREW, 5/16-18 x 1-1/4 Hex Head Cap, GR 5 33 7091706 1 NUT, 5/16-18 Hex Top Lock, GR B 34 7028046 1 BRACKET, Anti-Spin use with 7075672 Clutch Footnotes: NOTE 1: Purchase engine & engine parts, other than those listed, from engine manufacturer dealer. SERIES 0 & 1 29
CASTER, WHEEL & TIRE ASSEMBLY 30 SERIES 0 & 1
CASTER, WHEEL & TIRE ASSEMBLY Item Part No Qty Description Note 1 7057711 2 ASSEMBLY, Wheel & Tire- Gray (Incl. Items 3 & 4) -- 7029869 2 ASSEMBLY, Wheel & Tire- White (Incl. Items 2, 3, 5, 16, 17 & 18B) -- 7058167 2 ASSEMBLY, Wheel & Tire- Gray (Incl. Items 2, 3, 5, 16, 17 & 18C) 2 7022394 2 RETAINER, Flanged quantity shown is per tire 3 7029870 2 TIRE, 9 x 3.50-4, 4 Ply Smooth Tread 4 7057737 2 ASSEMBLY, Wheel (Incl. items 2, 5, 16, 17 & 18A) 5 7022395 1 BEARING, Roller quantity shown is per tire 6 7022151 1 SLEEVE, Axle quantity shown is per tire 7 7091922 1 NUT, 1/2-13 Hex Nyloc quantity shown is per tire 8 7091326 1 BOLT, 1/2-13 x 5-1/2 Hex Head Cap, GR 5 quantity shown is per tire 9 7042780 2 WELDMENT, Caster 10 7017711 2 PIN, Lynch 7/16 Heavy Duty 11 7019152 4 SPACER, Caster quantity shown is per tire 12 7021960 1 SPACER, Powdered Metal quantity shown is per tire 13 7023747 1 BUSHING, 1 quantity shown is per tire 14 7023556 2 BUSHING, Caster 15 7076998 2 FITTING, 1/4-28 Straight Lube 16 7012234 1 VALVE STEM quantity shown is per tire 17 7046430 1 FITTING, 1/4-28 45 Degree Lube quantity shown is per tire 18A 7046431 1 RIM, One Piece Steel, Gray quantity shown is per tire 18B 7029871 1 RIM, One Piece Steel, White quantity shown is per tire 18C 7075553 1 RIM, One Piece Steel 4 x 1-3/8 Bore quantity shown is per tire Footnotes: *Quantity per tire SERIES 0 & 1 31
36" MOWER DECK ASSEMBLY 32 SERIES 0 & 1
36" MOWER DECK ASSEMBLY Item Part No Qty Description Note 1 7012709 1 RING, 1 External Retaining 2 7013010 1 DECAL, Warning (CPSC Cut Finger) 3 7022522 1 DECAL, Warning 3 7073647 1 DECAL, Danger, Guard, Catcher English & Spanish 4 7023735 3 KNOB, Hood (5/16-18 thread) 5 7024156 1 DECAL, Caution- Operator Instruction 6 7027950 1 SPRING, Chute 7 7035710 1 V-BELT, 36 Deck Drive Sect. HB (Nom. Effective Length: 84.80 ) 8 7029277 1 HINGE PIN, Chute 9 7029278 1 SPRING, Idler 10 7076940 3 SCREW, 5/16-18 x 4-1/2 Hex Head Cap, GR 5 11 7091313 1 COTTER PIN, 3/32 x 1 12A 7046580 1 DECAL, SNAPPER Pro w/trademark 12B 7074862 1 DECAL, SNAPPER Pro 13A 7042460 1 DEFLECTOR, 36 (Weldment) 13B 7058871 1 CHUTE, 36 Ansi Compliant (Weldment) used on SPE151KW 14 7034963 1 COVER, 36 15 7041295 1 PIVOT, Idler Arm (Weldment) 16 7054018 1 ASSEMBLY, Idler Arm, 36 17 7057736 2 ASSEMBLY, Caster (Red) 18 7046294 1 WELDMENT, 36 Deck, Fixed Height, Express 19 7076998 2 FITTING, 1/4-28 Straight Lube 20 7091299 5 NUT, 3/8-16 Hex Nyloc 21 7091304 3 BOLT, 3/8-16 x 1 Hex Head Cap, GR 5 22 7091305 2 SCREW, 3/8-16 x 2 Hex Head Cap, GR 5 23 7013847 1 RETAINER, 3/8 Bolt 24 7091323 1 BOLT, 1/2-13 x 1-1/4 Hex Flange Lock, GR 5 25 7091528 9 WASHER, 3/8 I.D. Flat 26 7021128 6 SPACER 27 7091601 3 NUT, 5/16-18 Hex Flange Lock, GR 5 28 7090613 2 NUT, 3/8-16 Hex Flange Lock 29 7091322 1 WASHER, 1/2 Split Lock 30 7091316 1 NUT, 1/2-13 Hex, GR B 31 7091331 2 WASHER, 13/32 Flat 32 7044796 1 DECAL, 36 Deck 32 7075564 1 DECAL, 36 Silver 33 7077345 1 PAD Footnotes: SERIES 0 & 1 33
36" MOWER DECK ASSEMBLY 34 SERIES 0 & 1
36" MOWER DECK ASSEMBLY Item Part No Qty Description Note 34 7091547 2 BOLT, 3/8-16 x 3/4 Short Neck Carriage, GR 5 35 7046626 4 BUSHING, Caster -- 7054011 2 ASSEMBLY, Spindle not shown; see Cutter Housing Assembly page Footnotes: SERIES 0 & 1 35
36" DECK IDLER ASSEMBLY 36 SERIES 0 & 1
36" DECK IDLER ASSEMBLY Item Part No Qty Description Note 1 7034422 1 PULLEY, Idler (5.00 O. D.) 2 7091299 4 NUT, 3/8-16 Hex Nyloc 3 7091300 1 WASHER, 7/16 I.D. x 1 O.D. 4 7012709 1 RING, 1 External Retaining 5 7023556 2 BUSHING 6 7042448 1 IDLER ARM, 36 (Weldment) 7 7076998 1 FITTING, 1/4-28 Straight Lube 8 7091304 3 BOLT, 3/8-16 x 1 Hex Head Cap, GR 5 9 7041295 1 PIVOT, Idler Arm (Weldment) 10 7027220 1 SCREW, 3/8-16 x 3-1/4 Hex Head Cap, GR 5 11 7029723 2 SPACER 12 7036429 1 BRACKET, Idler (Pro 36) 13 7027198 1 BOLT, 3/8-16 x 1 Hex Flange Lock, GR 5 14 7091585 1 NUT, 3/8-16 Hex Center Lock, GR 5 or B 15 7035656 1 RETAINER, Belt - Idler Footnotes: SERIES 0 & 1 37
48" MOWER DECK ASSEMBLY 38 SERIES 0 & 1
48" MOWER DECK ASSEMBLY Item Part No Qty Description Note 1 7013010 1 DECAL, Warning (CPSC Cut Finger) 2 7022522 1 DECAL, Warning 2 7073647 1 DECAL, Danger, Guard, Catcher English & Spanish 3 7023735 4 KNOB, Hood (5/16-18 thread) 4 7024156 1 DECAL, Caution- Operator Instruction 5 7027327 1 PIVOT, Roller Pin (Weldment) 6 7027344 2 WASHER, 5/8 Flat 7 7027950 1 SPRING, Chute 8 7029245 1 PULLEY, Driven 5-3/4 O.D. 9 7029261 1 V-BELT, Secondary 48 (113 Long) 10 7029262 1 V-BELT, Primary 48 (66 Long) 11 7072915 1 SPRING, Primary 12 7029277 1 HINGE PIN, Chute 13 7029278 1 SPRING, Idler 14 7029281 4 STANDOFF, 4-1/2 Long (5/16-18 thread top; 3/8-16 thread bottom) 15 7091313 1 COTTER PIN, 3/32 x 1 16 7046580 1 DECAL, SNAPPER Pro w/trademark 16 7074862 1 DECAL, SNAPPER Pro 17A 7042464 1 DEFLECTOR, 48 Chute (Weldment) 17B 7050513 1 ASSEMBLY, Discharge Chute incl. items 24 (4), 29, 30, 31 & 32 (4) 18 7054013 1 48 COVER 19 7054020 2 ASSEMBLY, Caster Red (Fixed Deck) not shown; see Caster, Wheel & Tire Assembly page 20 7046902 1 WELDMENT, 48 Deck (Fixed Height) includes 4 of item 27 21 7054023 1 ASSEMBLY, Idler - 3 Spindle Deck 22 7076998 2 FITTING, 1/4-28 Straight Lube 22 7014669 2 FITTING, Lube Press-In for 3/16 hole 23 7079226 3 ROLLER, Low Density Polyethylene 24 7091299 8 NUT, 3/8-16 Hex Nyloc 25 7091304 4 BOLT, 3/8-16 x 1 Hex Head Cap, GR 5 26 7091305 2 SCREW, 3/8-16 x 2 Hex Head Cap, GR 5 27 7046626 1 BUSHING, Caster 28 7091619 4 NUT, 3/8-16 Hex Flange Lock -- 7054011 3 ASSEMBLY, Spindle not shown; see Cutter Housing Assembly page 29 7050590 1 WELDMENT, 48 Chute 30 7078146 1 CHUTE, Rubber 31 7078133 1 DEFLECTOR, Bottom 32 7091790 4 BOLT, 3/8-16 x 1-1/4 Square Neck Carriage, GR 5 Footnotes: SERIES 0 & 1 39
48" DECK IDLER ASSEMBLY 40 SERIES 0 & 1
48" DECK IDLER ASSEMBLY Item Part No Qty Description Note 1 7029273 1 PULLEY, Idler 2 7034422 1 PULLEY, Flat Idler, 5 O.D. 3 7091585 2 NUT, 3/8-16 Hex Center Lock, GR 5 or B 4 7012709 2 RING, 1 External Retaining 5 7023556 4 BUSHING 6 7042452 1 WELDMENT, Idler Arm, Secondary 7 7042450 1 WELDMENT, Idler Arm, Primary 8 7035657 1 SPACER, Idler Pulley 9 7091300 2 WASHER, 3/8 Flat or 7090517 10 7091305 1 SCREW, 3/8-16 x 2 Hex Head Cap, GR 5 11 7027220 1 BOLT, 3/8-16 x 3-1/4 Hex Head Cap, GR 5 12 7076998 1 FITTING, 1/4-28 Straight Lube 13 7042465 1 WELDMENT, Idler Pivot 14 7035656 1 RETAINER, Belt - Idler 15 7023747 2 BUSHING, Machine Footnotes: SERIES 0 & 1 41
CUTTER HOUSING ASSEMBLY 42 SERIES 0 & 1
CUTTER HOUSING ASSEMBLY Item Part No Qty Description Note 1 7029422 2 BEARING, Sealed 2 7029270 1 WASHER, Spindle 3 7029274 1 SNAP-RING, Spindle Shaft 4 7059311 1 ASSEMBLY, Spindle Shaft 5 7029254 1 SPACER, Bearing 6 7029271 4 SPACER, Blade 7 7075751 2 BLADE, 18 replaces 29246 (for 36 deck) 7 7075771 3 BLADE, 16-1/2 replaces 29247 (for 48 deck) 8 7016440 1 WASHER, Beveled 9 7063234 1 BOLT, 5/8-11 x 7-1/2 Hex Head Cap, GR 5 replaces 29256 10 7029275 1 FITTING, 1/4-28 Straight Lube 11 7029252 1 HOUSING, Cutter see Footnote 1 12 7029384 1 VENT, Spindle 13 7029302 6 BOLT, 3/8-16 x 1-1/4 Rib Necked 14 7029249 1 PULLEY, 5-3/4 O.D. for 36 deck 15 7063237 1 NUT, 5/8-11 Hex Flange Lock, GR B replaces 91736 16 7091299 6 NUT, 3/8-16 Hex Nyloc 17 7063238 1 SEAL, Nylos see Footnote 2 18 7013370 1 WASHER Footnotes: Note 1: 7054017 (Spindle Hsg. Sub-Assy) is made of one Item 11 & 12 & six Items 13. NOTE 2: To install Bearing Pre-Seal Kit (7063240) discard item 3 & replace with items 17 & 18 as shown. SERIES 0 & 1 43
DECALS (Pt. 1) 44 SERIES 0 & 1
DECALS (Pt. 1) Item Part No Qty Description Note 1 7073598 1 DECAL, Console (Pistol Grip, Gear) 1 7075759 1 DECAL, Console (Pistol Grip, Gear) (not shown; Similar to 73598) 2 7046580 1 DECAL, SNAPPER Pro w/trademark (13.19 long) 3 7036481 1 DECAL, SNAPPER Pro (8 long) 4 7074862 1 DECAL, SNAPPER Pro (16.7 long) appearance is similar to item 3 5 7058213 1 DECAL, Pro Express 6 7044796 1 DECAL, 36 Deck (white numbers) 6 7075564 1 DECAL, 36 Deck (silver numbers) 7 7044792 1 DECAL, 48 Deck (white numbers) 7 7075565 1 DECAL, 48 Deck (silver numbers) 8 7024156 1 DECAL, Caution- Operator Instruction 9 7022522 1 DECAL, Warning 10 7073594 1 DECAL, Caution (Open Drive Belt) 11 7044640 1 DECAL, SNAPPER (7.31 long) 12 7075760 1 DECAL, SNAPPER (8 long; not shown) Footnotes: SERIES 0 & 1 45
DECALS (Pt. 2) 46 SERIES 0 & 1
DECALS (Pt. 2) Item Part No Qty Description Note 13 7073612 1 DECAL, Operation (Gear Drive) 14 7013010 1 DECAL, Warning (CPSC Cut Finger) 15 7073560 1 DECAL, Shift 16 7058290 1 DECAL, Caution, Counterweight (36 ) 17 7058294 1 DECAL, Caution, Counterweight (48 ) 18 7073590 1 DECAL, Warning, Counterweight 19 7073556 1 DECAL, Throttle Control 20 7073558 1 DECAL, PTO Switch 21 7027733 1 DECAL, Ear Protection 22 7073557 1 DECAL, Ignition Switch 23 7073647 1 DECAL, Caution, Guard, Catcher 24 7073559 1 DECAL, Right Hand Control Footnotes: SERIES 0 & 1 47
ELECTRICAL COMPONENTS (Pistol Grip Handle) 48 SERIES 0 & 1
ELECTRICAL COMPONENTS (Pistol Grip Handle) Item Part No Qty Description Note 1 7045195 1 WIRING HARNESS, Pistol Grip Handle see also Pistol Grip Handle & Control Assemblies page Footnotes: SERIES 0 & 1 49
ELECTRICAL COMPONENTS (Loop Handle) 50 SERIES 0 & 1
ELECTRICAL COMPONENTS (Loop Handle) Item Part No Qty Description Note 1 7073317 1 WIRING HARNESS, Loop Handle Footnotes: SERIES 0 & 1 51
WIRING SCHEMATIC (Pistol Grip Handle) 52 SERIES 0 & 1
WIRING SCHEMATIC (Pistol Grip Handle) Item Part No Qty Description Note 1 -- -- WIRING SCHEMATIC (Pistol Grip Handle) Footnotes: SERIES 0 & 1 53
WIRING SCHEMATIC (Loop Handle) 54 SERIES 0 & 1
WIRING SCHEMATIC (Loop Handle) Item Part No Qty Description Note 1 -- -- WIRING SCHEMATIC (Pistol Grip Handle) Footnotes: SERIES 0 & 1 55
Parts Manual for MID-SIZE WALK BEHIND MOWERS SERIES 0 & 1 IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY. McDonough, GA, 30253 U.S.A. COPYRIGHT 2005 SNAPPER PRODUCTS, INC. ALL RIGHTS RESERVED. Revision 6, 10/21/2005