Thank you for your interest in the Copper Battery Terminals through the farm magazine. We have enclosed our literature on the battery terminals and related products along with our product listing and catalog sheets. If you need any further information or need to place an order, please call our toll free number @ 800/211-051. Sincerely, Don Fleming DF SALES TX, LLC
BATTERY TERMINALS DIE CAST COPPER CRIMP TERMINALS * All clamps, lugs, and fasteners are tin plated twice as thick as industry standards * All clamps include tin plated 5/1" battery bolts and shoulder nuts * All clamps and lugs are made of die cast copper STRAIGHT CRIMP 90 DG RIGHT ANGLE RIGHT ELBOWS LEFT ELBOWS HDBT - 1 & 2P RA-1/0P EL-1/0P TH-1/0P HDBT - 1 & 2N RA-1/0N EL-1/0N TH-1/0N HDBT 1/0 & 2/0P RA-2/0P EL-2/0P TH-2/0P HDBT 1/0 & 2/0N RA-2/0N EL-2/0N TH-2/0N $5.25 $7.28 $7.28 $7.28 MAGNA-LUGS MagnaLugs are superior to standard tube lugs in five important ways: * Wider pads for better electrical contact * Thicker pads for greater strength * 80% thicker walls for greater conductivity and strength * MagnaLugs use same crimp settings as battery clamps, saving you time, trouble and errors * MagnaLugs exceed SAE conductivity standards ML-1-3/8 #1 3/8 STUD HOLE $3.8 ML-100-3/8 1/0 3/8 STUD HOLE $3.8 ML-100-1/2 1/0 1/2 STUD HOLE $3.8 ML-200-3/8 2/0 3/8 STUD HOLE $3.8 ML-200-1/2 2/0 1/2 STUD HOLE $3.8 ML-300-1/2 3/0 1/2 STUD HOLE $5.55 ML-400-1/2 4/0 1/2 STUD HOLE $5.85 MS-200 2/0 MAGNA SPLICE $3.75 PH. (800) 211-051
BATTERY TERMINALS RETRO-FIT TERMINALS *Replacement terminal for threaded stud or side terminal batteries *3/8" stud hole *Use for single termination only. Retro-Fit terminals are not stackable *Use with closed cap nuts for stud battery applications or 3/8 flange bolt for side terminal batteries RF-1 #1 TOP OR SIDE RETROFIT $ 4.50 RF-2/0 2/0 TOP OR SIDE RETROFIT $ 4.88 ST-2/0 2/0 DOUBLE BARREL RETROFIT $.00 3750 STAINLESS NUT $ 2.18 STACKABLE TERMINALS *Designed for threaded stud or side terminal batteries *3/8" stud hole *Use with closed cap nuts for stud battery applications or 3/8 flange bolt for side terminal batteries *Stackable for multiple battery hook-ups *Locking teeth "bite" into battery terminal for non-rotating connection *Different cable gauges can be stacked, for example: 2/0 gauge cable between batteries and 4/0 gauge cable to starter or ground TOP OR SIDE MOUNT STACKABLE PL-1 1 GA $ 5.25 PL-4 4 GA $ 5.25 PL-1/0 1/0 $ 5.25 PL-2/0 2/0 $ 5.3 PL-3/0 3/0 $.75 PL-4/0 4/0 $.98 TOP OR SIDE MOUNT DOUBLE STACKABLE MR-1/0 & 2/0 1/0 & 2/0 $.38 MR-3/0 3/0 $ 3.75 MR-4/0 4/0 $ 7.13 www.dfsalestx.com PH. (800) 211-051
HEAT SHRINK TUBING Using heat shrink tubing will extend the life of your cables and give you more dependable service. FEATURES: PROTECTS AGAINST CORROSION Heat shrink tubing protects battery cables and terminals from corrosive acid fumes near batteries. It also protects against oil, fuel, water, salt, grease, animal acids and other chemicals. IDENTIFIES POSITIVE & NEGATIVE POLARITY Use red heat shrink tubing on positive cables, black on negative cables. Color coded battery cables are easier to route and to service. ACTS AS STRAIN RELIEF & PREVENTS ABRASION Heat shrink tubing acts as a strain relief between the cable and terminal. It can also be used where abrasion is a potential cause of failure. Long, heavy battery cables can fail because of fatigue caused by vibration. PART NO. SIZE PRICE/FT 1734 1/8 $ 3.30 1735 3/1 $ 3.88 173 1/4 $ 4.4 1737 3/8 $ 5.25 1738 1/2 $.00 1739 3/4 $ 7.50 1740 1" $ 9.90 PH. (800) 211-051
TOOLS HEX CRIMP TOOL *Made in U.S.A. *Designed for heavy duty battery terminals *Crimps terminals 8 Ga - 250MCM (/0 Ga) *Adjustable crimp dies permanently attached *Die settings have letter, number, and color codes *Crimps all major brands of battery terminals, copper lugs, and splices *Insulated grips for comfort and safety #1090 Hex Crimp Tool $ 292.50 BATTERY CABLE CUTTER *Cuts cable up to 2/0 *Only 9" long, fits any tool box *Insulated grips #1011 Battery Cable Cutter $ 37.50 BRUTE TERMINAL CRIMPER *Inexpensive, simple crimping tool *Use with hammer or vise *Crimps 8 Ga - 4/0 Ga terminals *Spring loaded pin locks in 'up' position for loading terminal and cable. Pin is then released to hold terminal securely during crimping SKT-840 Brute Terminal Crimper $ 41.25 COPPER POWER WELDING CABLE *Made with very fine copper wire and insulated with a synthetic rubber *More flexible than battery cables, especially in cold temperatures *Easier to route in tight places WC-931 1 Ga Welding Cable 3.45 /ft WC-9310 1/0 Welding Cable 4.5 /ft WC-9320 2/0 Welding Cable 5.3 /ft PH. (800) 211-051
MASTER DISCONNECT SWITCH LEVER OPERATED - -3 VOLT 180 AMPS CONTINUOUS CAPACITY, 1000 AMPS IN RUSH S.P.S.T. (OFF-ON) TWO STUD TERMINALS for battery circuit only. Does not disconnect alternators, engine must be shut off to avoid potential damage to alternator diodes. *Incorporates heavy duty contacts *One piece die-cast housing sealed with O-rings at base and mounting stem to keep out dust and moisture *Large die-cast lever for ease of operation *Two 3/8" copper stud terminals with hex nuts and lockwashers *Overall length 4-3/8" - diameter 2-5/8" approx. *Conforms to requirements of U.L. #558 *Mounting stem 3/4" diameter, 1/2" long, with two hex nuts and lockwashers *Designed for protection against battery drain, electrical fires, tampering and theft *Fits panels up to 1/4" thick #51-902 Master Disconnect Switch Includes two 2/0 copper battery lugs w/ 3/8 hole and face plate $29.00 PH. (800) 211-051
$295 BAT ASSORTEMNT Serviced By: COPPER BATT TERMINAL ASSORTMENT 1739 3/4 BLACK D/W HEAT SHRINK TUBING 1 FT BATTERY CLEANER & PROTECTOR HDBT-2/0P 2/0 POS STR CRIMP BATT TERMINAL HDBT-2/0N 2/0 NEG STR CRIMP BATT TERMINAL HDBT-1P 1 GA POS BATTERY TERMINAL HDBT-1N 1 GA NEG BATTERY TERMINAL ML-1-3/8 1739A 3/4 RED D/W HEAT SHRINK TUBING 1 FT 1 SKT-840 Battery Crimping Tool RA-2/0P 2/0 POS FLAG BATT TERMINAL 2 RA-2/0N 2/0 NEG CRIMP BATT TERMINAL 1 GA MAGNA LUG 3/8 STUD ML-200-3/8 2/0 MAGNA LUG 3/8 STUD ML-200-1/2 2/0 MAGNA LUG 1/2 STUD 1 2 PH. (800) 211-051
1090K HEX CRIMP TOOL KIT HDBT-1P 1 GA POS BATT TERM HDBT-1N ML-1-3/8 HDBT-2/0N HDBT-2/0P 1 GA NEG 1 GA MAGNA LUG 3/8 STUD 2/0 NEG STR 2/0 POS STR BATT TERM CRIMP BATT TERMINAL CRIMP BATT TERMINAL 1739 3/4 D/W HEAT SHRINK BLK 2 ML-200-3/8 RA-2/0P 2/0 MAGNA LUG 2/0 POS FLAG BATT TERM 3/8 STUD HEX CRIMP TOOL RA-2/0N ML-200-1/2 2/0 NEG FLAG BATT TERM 2/0 MAGNA LUG 2 1/2 STUD 1739A 3/4 D/W HEAT SHRINK RED QTY PART # HDBT-2/0P HDBT-2/0N HDBT-1P HDBT-1N ML-200-1/2 ML-200-3/8 ML-1-3/8 1 GA MAGNA LUG - 3/8 STUD 1' 1739 3/4 D/W HEAT SHRINK BLACK 1' 1739A 3/4 D/W HEAT SHRINK RED 1 9929 1 1090 1 710-20 2 RA-2/0P 2 RA-2/0N 1 FC-4 Description POS 2/0 CRIMP BATT TERM NEG 2/0 CRIMP BATT TERM POS 1 GA CRIMP BATT TERM NEG 1 GA CRIMP BATT TERM 2/0 MAGNA LUG - 1/2 STUD 2/0 MAGNA LUG - 3/8 STUD CARRYING CASE HEX CRIMP TOOL BATTERY CLEANER & PROTECTOR 2/0 POS FLAG BATT TERM 2/0 NEG BATT TERM WHIP 2 OZ $475 PH. (800) 211-051