00 / poppet valves electromagnetic actuated, directly controlled, / NPT or flanged with NAMUR Interface TÜV-approval based on IEC 6 8, DIN V Valves for safety systems up to SIL Solenoid valve also suitable for low power consumption in non hazardous areas without barrier Solenoid: ATEX category II GD, type of protection Ex ia IIC T/T6, EX td A IP66 T9 C, suitable for zones, (gases) and, (dusts) Working from 0 bar up High operational reliability even after long periods of inoperation Suitable for control and instrument quality air Also suitable for open air installation NAMUR FLANGE: With integrated exhaust air recirculation DIN EN 68 IEC 68 up to SIL Approval depends on magnetic system, see page! Technical features Medium: Compressed air, filtered, nonlubricated and dry Other fluids on request Operation: Direct solenoid operated poppet valves Flow direction: Optional Mounting position: Any, but preferably with solenoid vertical Port size:, / NPT or flanged with NAMUR Interface Operating pressure: 0...0 bar Fluid/Ambient temperature: -... +60 C Depending on solenoid system Air supply must be dry enough to avoid ice formation at temperatures below + C. For outdoor installation please protect all connections against the penetration of moisture! Materials: Housing: brass.00 (Ms 8), stainless steel.0 (6 L) hard-anodised aluminium.06 Internal parts: stainless steel, brass Solenoid housing: aluminium, anodized hartanodisiert.06 Seals: NBR Technical data Symbol Port size Operating *) kv-wert Material Weight without Dimension Model pressure (bar) (Cv (US) kv x, Seat Housing solenoid (kg) No. 0... 0 0.0 NBR Brass 0,6 0088.00 / NPT 0... 0 0.0 NBR Brass 0,6 0087.00 0... 0 0.0 NBR Stainless steel 0,6 0086.00 / NPT 0... 0 0.0 NBR Stainless steel 0,6 00.00 NAMUR 0... 0 0.0 NBR Aluminium*) 0, 009.00 / NPT NAMUR 0... 0 0.0 NBR Aluminium*) 0, 0090.00 NAMUR *) 0... 0 0.0 NBR Aluminium*) 0, 0009.00 *) With gaseous and liquid fluids up to 0 mm /s *) Hard-anodised *) P port in flange interface Note: At an ambient temperature of -0 C, higher air consumption may be experienced for short periods. / N/en..09.0
00 Solenoid parameters for use in intrinsically safe circuits Symbol Switch-on Allowed current max. current min. Pick-up delay typical *) (s) Protection class Temperature Ambient/Fluid ( C) Weight (kg) Model... 8 0 0 approx. 0,... IIG Ex ia IIC T6 IIG Ex ia IIC T IID IP66 T9 C -0... + -0... +70-0... +70 0,8 00 *) depending on intrinsical current supply Solenoid parameters for use in non harardous locations Symbol Switch-on Allowed current max. current min.... 6, 7 0,8 at V Power consumption (W) Pick-up delay typical *) (s) Protection class Temperature Ambient/Fluid ( C) Weight Model (kg) 0,... s IP 66-0... +80 0,8 00 *) depending on intrinsical current supply Accessories Silencer *) Exhaust guard *) Throttle control plate Flange plate Yoke M/S (G/) 06 (G/, / NPT) 009 (for G/ only) 06790 (NAMUR single connection plate, for G/ only) 009 C/S (/ NPT) *) For indoors use only *) For outdoor use Page 0679 (NAMUR-rip use in combination with 06790, Alu) Operating sequence 8 V V ma Supply V 0 V Off Charging process 0 0 00 7 80 60 0 0 0 0 0 Off Current process Off Valve operation status Off Current supply units: Intrinsically safe power supply units can be choosen in a list of compatibility in www.norgren.com When selecting an intrinsically safe power supply, it is important to observe the maximum permissible values acc. to the EC-Type-Examination Certificate PTB 0 ATEX 00 respectively IECEx PTB 0.000 Ui 8 V, LI 0 ma, Pi, W The effective internal capacities Ci; and inductivities Li of the solenoid are negligibly low. Function of solenoid drive To switch the direct operated valve, a certain energy is required. This energy is stored in a condenser. The charging is V. The higher the supply, the shorter the charging time. As soon as the charging has been reached, the valve switches. The small current now flowing through the coil is sufficient to hold the valve in the open position. At least 0 ma are required for this. N/en..09.0 /
00 Dimensions Valves 70,.7. 9 70, 0 7, M ø0 M6 08 98. 7 0 M0 x, 9 70, For port size see general information mm deep 0 7, M, 7, ø ø,,, 6 7, 7, ø ø,,,, 6 7 / N/en..09.0
00 Circuit diagram NAMUR hole pattern (driving side) M Port (A) Coding stud threaded M (0 deep) Port (R) NAMUR quick exhaust module for a better kv-value by exhaust see data sheet..80 NAMUR interlinking plates in redundancy design for»safety exhausting«and»safety ventilating«see data sheet..80 Single connection plate Model: 06790 NAMUR slot Model: 0679 M (x), 0 ø 9, 0 6 9 0, 6 9, ø 60 ø 9 ø, 7 N/en..09.0 /
00 Yoke Model: 009 Throttle control plate Model: 009 6 x, 0 Silencer Model: M/S, C/S Exhaust guard Model: 06, 8 0 ø / ø / M 76 8 7, M B B A A Warning These products are intended for use in industrial compressed air and fluid systems only. Do not use these products where pressures and temperatures can exceed those listed under»technical features«. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult NORGREN. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products. / N/en..09.0