INSTRUCTIONS 0 Y-DROP 0 Y-DROP REGISTRATION Please visit productregistration.0yieldcenter.com to complete the product registration for your 0 Y-DROP so we can better support our products from day one and ensure you have the latest upgrades, warranty parts and technical support. Thank you! 0YIELDCENTER.COM V -.0.0
INSTRUCTIONS 0 Y-DROP INTRODUCTION Before beginning, it s important to know where each mounting bracket fits relative to the row spacing involved. The 0 Y-DROP unit should be precisely centered on the machine, as this is critical to the assembly of the system to the sprayer and for mounting the system to your sprayer boom. There are, however, many boom variations among all sprayer models. Your sprayer may not be identical to the model in the following steps of the guide, and the pictures may not exactly reflect your model. While these steps will help you install most of your 0 Y-DROP system, you may need to custom-fit some components with your particular boom. RECOMMENDED TOOLS Ratchet wrench with /" and 9/" deep well sockets /8" -point socket /" and 9/" combination wrenches # Phillips screwdriver (for the shield installation) TORQUE VALUES Refer to these torque values when tightening all fasteners /" stainless U-bolt ft/lbs /" stainless Set screw ft/lbs /8" carbon U-bolt ft/lbs /" carbon U-bolt 0 ft/lbs /" carbon Stop bolt 0 ft/lbs QUESTIONS Call our Product Support team at 888--890
INSTRUCTIONS 0 Y-DROP I. ESTABLISH DROP LOCATIONS Step Figure Step Locate the center of the machine and identify the location of all the drops. On the sprayer boom, mark where each riser mount will be located. This will ensure that the extension tubes will not interfere with the riser mounts. For the primary boom; starting at the wing fold pivot pin, measure out and make marks at 8", 08", 8", " and 89" (all measurements are ±"). Repeat for the other primary boom. 8" 08" 8" " 89" Figure 0YIELDCENTER.COM
INSTRUCTIONS 0 Y-DROP II. INSTALL MOUNT ASSEMBLIES ON THE OEM PRIMARY BOOM Figures and Step With the threads pointing down, install diamond U-bolt () on the top side of the 7 OEM primary boom. Bag AM (.7") - mounting locations containing the added OEM gussets on primary booms Bag AL (.0") - mounting locations with no added OEM gussets on primary booms Figure Step Install diamond boom clamp () on the bottom of the OEM primary boom. Step Install " top plate (). Step Install bracket assembly () and flange lock nuts (). Hardware Kit D Step Install carriage bolts () and flange nuts. Hardware Kit D Step Install extension tube (7). Figure Figure Step 7 Install boom bracket () onto the extension tube. Step 8 With the threads pointing down install square U-bolts () plus the /" extra thick washers and the /" nuts. Hardware Kit A Step 9 Install stop bolts () at both the front and the rear of the extension tube. Figure Hardware Kit B Figure Step 0 Install stainless steel set screws and jam nut assemblies () onto the bracket assemblies. Hardware Kit D Repeat Steps -0 the remaining mount assemblies on the OEM primary boom. Figure 0YIELDCENTER.COM
INSTRUCTIONS 0 Y-DROP III. 008 + CENTER SECTION SQUARE TUBE INSTALLATION Figures and 7 Step Install bolts () over the OEM center section boom. Step Place " top plates (), spacer plate () and bracket assembly () into position Step and install /8" flange nuts (). Install extension tube () onto bracket Figure Step assembly (). Install carriage bolts (7) and the 8 flange nuts. Step Install boom bracket (8). Step Install stop bolt assemblies (9) at the front and rear of the extension tube. 9 7 7 Figure 7 0YIELDCENTER.COM
INSTRUCTIONS 0 Y-DROP III. PRE-008 CENTER SECTION SQUARE TUBE INSTALLATION Figures 8 and 9 Step Install bolts () over the OEM center section boom. Step Step Place " top plates () and bracket assembly () into position and install /8" flange nuts (). Install extension tube () onto bracket Step Figure 0 assembly (). Install carriage bolts () and the flange nuts. Step Install drop tube () onto the extention Figure 8 tube and install stop bolt (). Hardware Kit B Repeat steps - for the other center section mount. Figure 9 Figure 0
INSTRUCTIONS 0 Y-DROP IV. INSTALL 0 Y-DROP BOOM Figure Step Assemble ' boom sections () using the 8" boom connectors () and the supplied hardware. Hardware Bag CC Step Step Repeat Step as needed in order to assemble the entire 0 Y-DROP boom. Set the 0 Y-DROP boom assembly onto boom bracket (). Figure Repeat Steps - for the remaining boom assemblies. CAUTION: The 0 Y-DROP boom assembly may weigh up to 0 lbs. (8 kg). Exercise caution and enlist help for this process. Figure Step In order to span the full length of the center section 0 Y-DROP boom, you will need to cut and drill one of the ' boom sections to '. Mount this ' section between two full ' boom sections. Drill a 7/" through hole centered " from the outside edge. Figures and Step Install square U-bolt (), the /" extra thick washers, and the /" nuts over the 0 Y-DROP boom (). Hardware Kit A Figure Figure Step Step 7 Install stop bolt () at both the front and the rear of the extension tube. Repeat for remaining stop bolts. Hardware Kit B Install stainless steel set screw and jam nut assembly (). See Figure for detail. Repeat for the remaining mount assemblies on the primary boom. Figure 0YIELDCENTER.COM 7
INSTRUCTIONS 0 Y-DROP V. INSTALL BREAKAWAY ASSEMBLY - ONE PIECE Figure Step Install breakaway assembly - one piece () using the square U-bolts () and the extra thick washer and Nylock nut. Repeat for the remaining breakaway assemblies - one piece. Hardware Kit C NOTE: The alignment and quantity of the mounts will depend on your row spacing. Figure Step Install riser tube assembly () into the breakaway assembly - one piece (). Figure Step Install pin (). Repeat Steps and for the remaining riser tube assemblies. NOTE: Included in most sprayer mount packages are standard riser mounts to be used when primary booms are folded and in transport mode. These standard riser mounts should be mounted in locations that allow you to relocate the drops away from potential tire interference. See "Install Riser Mounts Without Breakaway Assemblies" section on next page for more instructions. Figure 0YIELDCENTER.COM 8
INSTRUCTIONS 0 Y-DROP V. INSTALL RISER MOUNTS WITHOUT BREAKAWAY ASSEMBLIES (OPTIONAL) Figure 7 Step Figure 8 Step Install riser mount () using the square U-bolts () and the extra thick washer and Nylock nut. Repeat for the remaining riser mounts. Hardware Kit C Install riser tube assembly () into the riser mount (). Step Install pin (). Figure 7 Repeat Steps and for the remaining riser tube assemblies. Figure 8 0YIELDCENTER.COM 9
INSTRUCTIONS 0 Y-DROP VI. INSTALL SHIELDS AND RISER HOSES Figure 9 Step Install shield () onto riser tube (). Figure 0 Step Install base unit () onto riser tube (). Figure Step Figure Step Assemble drag hoses () to 0 Y-DROP base and secure with hose clamps (). Note the orientation of the drag hose clamps. The tails should point inward. Figure 9 Figure 0 Figure Figure 0YIELDCENTER.COM 0
INSTRUCTIONS 0 Y-DROP VI. INSTALL SHIELDS AND RISER HOSES (continued) Figure CAUTION: Do NOT use a drill or impact driver for Steps and. Step Install two ½" screws (). Figure Step Install two ¾" screws (). Step 7 Figure Step 8 Figure Step 9 Install rubber washer () into the Y. Install riser hose assembly () into the Y. Route riser hose assembly () as shown in Figure. Step 0 Install the riser hose assembly to the OEM nozzle body. Figure Step Use equally spaced plastic ties to secure the riser hose assembly. Repeat Steps - for the remaining 0 Y-DROP Shields. Figure INSTALLATION COMPLETE. 0YIELDCENTER.COM All other trademarks are the property of 0 Yield Center, its affiliates and/or its licensors. 0 0 Yield Center. All rights reserved.