Technical Application Guide for UP-SHINE Tri-proof LED light UP-TRP2-15-5W
Introduction stainless steel buckle for optional Tri-proof LED light adopts high lumen SMD light source, a compact high PF driver and insulated fireproof PC cover into a traditional tube replacement. The lampshade with, high transparency, soft&uniform light distribution; latch design make the lampshade disassembly and assembly easier; the natural-rubber seal ring has cable joint, dustproof waterproof rating as IP65. Anti-corrosion, shock resistance, easy cleaning, energy saving and environmental protection. Up to 7% energy saving compared to standard CFL Long lifetime of 5, hours 12 wide beam angle CCT: 3K 4K 5K 57K No UV/IR light Environment friendly, without Mercury or any other hazardous substances Application notes IP65 for indoor use Professional electrician for installation only Switch off before installation Do not touch when in use Application Areas Tri-proof LED light can be used in factory, warehouse, workshop, and other lighting area with high humidity and dusty places. Certificate SAA
Product Information 74 1515 116 Technical Specifications Model Voltage Power Power Factor Lumen (±5%) CCT Beam angle Lifespan CRI Dimmable Dimension UP-TRP2-15-5W AC1-24V 5W.9 425 3K 5 4K 49 5K 475 57K 12 o 5,h 8 No 1515*116*74mm Driver data Sheet Driver data Input rated Voltage Frequency Input Voltage Non-dim AC1-24V 5/6Hz AC85-265V Efficiency 88% Total load Wattage 5W±5% Power Factor.9 Rated input current Full load output Voltage Rated output current Output current range.56a DC6-75V 57mA 57mA±5% Power tolerance ±5% Current output tolerance ±5% Short circuit protection Over voltage protection Over temperature protection PASS PASS PASS Withstand voltage Fixture Compatibility Rated Wattage Electrical Classification Ingress Protection Operating Temp Operating Humidity Storage Temp 5W Ⅰ IP65-2 o C~45 o C ~9% -2 o C~65 o C
Spectral Distribution 3K 4K.8.7.6 Max=11793 [1.=2] 3.58 SDCM F3K.8 Max=11721 [1.=2].7.6 1.87 SDCM F4K.5.4.3 x=.4471 y=.487.5.4.3 x=.3839 y=.3841.2.2.1.1.. 38 5 6 7 8 38 5 6 7 8 5K 57K.8.7.6 Max=5781 [1.=2] 1.95 SDCM F5K.8 Max=8438 [1.=2].7.6 5.64 SDCM F57K.5.4.3 x=.347 y=.364.5.4.3 x=.3235 y=.3468.2.2.1.1.. 38 5 6 7 8 38 5 6 7 8 Photometric Diagram 3K 4K Beam diagram -12-9 -/+18 12 9 1 9 8 MH=1m C/18 C9/27 Flux out: 2154 lm -12-9 -/+18 12 9 15. 13.5 12. MH=1m C/18 C9/27 Flux out: 2444 lm 2 7 3 1.5 4 6 5 6 9. 7.5 6 4 9 6. 8 3 12 4.5-3 1 3 2 1-3 15 3 3. 1.5 UNIT: cd AVERAGE BEAM ANGLE(5%): 125.7 DEG -25-2 -15-1 -5 5 1 15 2 25-25 -2-15 -1-5 5 1 15 2 25 Height Eavg, Emax Angle: 115.17deg Diameter UNIT: cd Height Eavg, Emax Angle: 113.18deg Diameter AVERAGE BEAM ANGLE(5%): 127.5 DEG 5K 57K Beam diagram Beam diagram -12-9 -/+18 12 9 15. 13.5 12. MH=1m C/18 C9/27 Flux out: 2439 lm -12-9 -/+18 12 9 15. 13.5 12. MH=1m C/18 C9/27 Flux out: 222 lm 3 1.5 3 1.5 6 9. 7.5 6 9. 7.5 9 6. 9 6. 12 4.5 12 4.5-3 15 3 3. 1.5-3 15 3 3. 1.5 UNIT: cd AVERAGE BEAM ANGLE(5%): 126.8 DEG -25-2 -15-1 -5 5 1 15 2 25-25 -2-15 -1-5 5 1 15 2 25 Height Eavg, Emax Angle: 113.66deg Diameter UNIT: cd Height Eavg, Emax Angle: 112.99deg Diameter AVERAGE BEAM ANGLE(5%): 127.9 DEG
Polar Diagram Comparison -15 O +/-18 O 15 O -12 O 12 O -9 O 9 O 3 6-6 O 9 6 O 12-3 O 15 3 O O AVERAGE BEAM ANGLE (5%): 127.9DEG UNIT: cd C/18, 141.4 deg C3/21, 135.8 deg C6/24, 121.1 deg C9/27, 113.3 deg Driver lifetime & LED light decay rate Driver Lifetime LED Light Decay Rate 9 11%.4 Lifetime (hours) 8 7 6 5 4 3 2 1 65 o C 75 o C 85 o C 95 o C 15 o C Capacitor Tc ( o C) % Luminous Flux 15% 1% 95% 9% 85%.35.3.25.2.15 8% 75% FLUX.1.5 U'V' 7%. 1 2 3 4 5 6 7 8 9 1 LifeTime (hours) Temperature The testing is operated at 25 C The lifetime of capacitor, minimum of 5, hours if operated at 15 C, will be doubled whenever the temperature drops 1 C The highest withstand temperature of IC, MOS could be 12 C The highest withstand temperature of LED junction temperature is 15 C 1 Temperature ( o C) 9 8 7 6 5 4 3 2 1 11:13:13 11:31:1 11:49:1 12:7:1 12:25:1 12:43:1 13:1:1 13:19:1 13:37:1 Time 13:55:1 14:13:1 14:31:1 14:49:1 15:7:1 15:43:1 16:1:1 16:19:1 16:37:1 IC Capacitor MOS PCB LED Fitting Environmental temperature The driver lifespan is based on capacitor working temperature.
Installation Suspended 1. Open the lamp by screw driver, take out the accessory pack from the lamp. 2. Cut off the power, fix the holders of suspending ropes on the ceiling. L = BROWN N = BLUE = YELLOW-GREEN 3. (a)connect the AC cables to the terminal block(inside wire 1-2.5mm2); (b)protect the PCB from being damaged in the whole installation process. 4. Assemble the lamp. 5. Lock the lamp fixture with screws, fix the mounting brackets on the back of lamp. 6. Connect the suspending ropes to the lamp. Surface Mounted 1. Open the lamp by screw driver, take out the accessory pack from the lamp. 2. Cut off the power, fix the mounting brackets on the ceiling.
3. (a)connect the AC cables to the terminal block(inside wire 1-2.5mm2); (b)protect the PCB from being damaged in the whole installation process. 4. Assemble the lamp. 5, Lock the lamp fixture with screws. 6. Firmly attach the lamp to the mounting brackets. Packaging Information SIZE(CM) N.W/pc (KGS) G.W.(KGS) Q'TY(PCS) Carton 154.5*24.5*34.5 2.3 22 8 2'' standard container 4'' standard container CTNS Q'TY(PCS) VOLUME(CBM) 21 168 28 42 336 56 Phone: +86 755 2919 7332 Add: 2nd building Dingfeng High-Tech Zone, Fuyuan 1st road, Fu Yong Sub-district, Bao'an, Shenzhen China