IDC.54mm R CONNECTOR IDC Disconnectable Insulation displacement connectors for.7mm pitch ribbon cables pitch Features Twin U-slot ID section The twin U-slot is the most important IDC element in eam JST s R connectors. s shown in the figure, wire conductors are connected Slot eam eam supporter between the slots of U-shaped parallel beams, and the Conductor distance between each adjacent pair of beams is designed to be one third of the pitch of wire Double-leaf contact strands. Two-die processing and selective gold plating Two precision dies are used to blank and form the contacts. fter the first die blanks the contacts, they are gold plated at crucial points. Then, the contacts are formed by the second To keep pace with the rapid developments in electronics, internal and external connection systems are naturally increasing in density. t the same time, labor requirements and overall costs must be minimized. R connectors meet all of these requirements, while providing increased reliability. These connectors, whose materials, shapes, dimensions, and surface treatments have been carefully selected, are based on the latest technological information that has been accumulated and improved over years of experience in crimping connection technology. die. This eliminates unnecessary gold-plating and overall costs are minimized. This innovation is another example of our industry-leading technology. Selective gold-plated posts Header posts are also selectively gold-plated. While square wire material is used for production of conventional posts in loose pieces, continuous flat strip is used for production of our post in chain form. This allows selective gold-plating and provides cost reduction. Cost-efficient JST s unique technology allows it to produce connectors that are extremely reliable and cost-efficient. Interchangeable cables and connectors R connectors fit commercially available.7mm pitch flat ribbon cables. variety of ribbon cables are offered according to Short locking lever the purpose. Moreover, the R series receptacles and header are interchangeable with the similar type of connectors commercially available. Contact JST before procuring cables and other manufacturer s mating connectors. Long locking lever * Compliant with RoHS. * Refer to "General Instruction and Notice when using Terminals and Connectors" at the end of this catalog. * Contact JST for details. Standards 0 Recognized E389 Certified LR08
R CONNECTOR Receptacle Specifications Characteristics Current rating Voltage rating Temperature range Materials.0 C, DC 300V C, DC Contact Phosphor bronze Nickel-undercoated, selective gold-plated Copper-undercoated, tin-plated (reflow treatment) (including temperature rise in applying electrical current) -55 C to + C(gold-plated) -55 C to +05 C(tin-plated) Receptacle housing Glass-filled PT, UL94V-0, black Glass-filled PT, UL94V-0, black Glass-filled PT, UL94V-0, black Contact resistance Initial value/0mω max. (gold-plated) mω max. (tin-plated) fter environmental testing/ 5mΩ max. (gold-plated) mω max. (tin-plated) Insulation resistance 5,000MΩ min. Withstanding voltage pplicable wire 0V C/5 seconds *Contact JST for details. WG #8,.7mm pitch ribbon cable pplicable cables Ribbon cables conforming to the following specifications can be used with R connector receptacles. Contact JST for details. Dimensional tolerance (mm) No.of conductors (n) P W 0 to 4 ±0.8 ±0.3 6 to 6 ±0.8 ±0.3 to ±0.38 ±0.3.7x(N-)= P.7±0.05(pitch) Insulator Conductor.7xN= W WG #8 solid wire Construction: 0.3mm dia. Material: Tin-plated annealed copper wire 0.9 Conductor WG #8 stranded wire Construction: 7/0.7mm dia. Material: Tin-plated annealed copper wire Insulator Soft vinyl chloride Note: N --- Number of circuits
R CONNECTOR Model number identification Note: Series name R S T 00 Product name: Receptacle Number of circuits: 0, 4, 6, 0, 6,,,, Number of guide ribs: 0 to circuits... circuits... 0,, circuits..., Connection method: T... Through type S... Short lock through type With or without strain relief 0... Without... With Contact material:... Phosphor bronze for spring Surface finish 00... Gold-plated (flash) 0... 0.micron gold-plated 03... 0.4micron gold-plated 04... 0.76micron gold-plated 90... Tin-plated (reflow treatment) The standard gold-plated type is identified by the suffix number [-00], but this suffix number is usually omitted. The gold-plated type identified by [-000] is indicated by [-0] for short. Other types must be identified by the full code number. Special types do not conform to the above coding system. Receptacle for long locking lever header C Receptacle for short locking lever header 0.4 <Note > Polarizing identification Guide rib 3.7 7.0 3.4 6.0 <Note > Polarizing identification Guide rib 7.0 3.4 0.4.54 4.0.0 6. Receptacle housing <Note >: Height without strain relief.54 <Note >: Height with strain relief 4.0.0 6. 0 4 6 0 6 Type of cover housing No.of guide ribs 0 Model No. Gold-plated receptacles With strain relief R-S0T R-S4T R-S6T R-S0T R-S6T R-ST R-ST R-S0T R-ST R-ST R-ST R-ST Without strain relief R-S0T-0 R-S4T-0 R-S6T-0 R-S0T-0 R-S6T-0 R-SS-0 R-ST-0 R-ST-0 R-SS-0 R-S0T-0 R-ST-0 R-ST-0 R-SS-0 R-ST-0 R-ST-0 RoHS compliance Tin-plated products display (LF)(SN) on a label. Tin-plated receptacles (With strain relief) R-S0T-90 R-S4T-90 R-S6T-90 R-S0T-90 R-S6T-90 R-ST-90 R-ST-90 R-S0T-90 R-ST-90 R-ST-90 R-ST-90 R-ST-90 0.6 5.4 7.78.86 30.48.64 48.6.96 73.66 7.30.38 4.9 30.00 37.6 47.78 55. 68.0 80.80 C 3.00 8.08 0.6.70 33.3 43.48 5.0 63.80 76. Q'ty / box 300 00 00 00 00 75 75 75 3
R CONNECTOR and cover housing Indicate the Model No. shown below when ordering strain relief and cover separately. JST 4.4 6. 3.4 0 4 6 0 6 R-SR0T- R-SR4T- R-SR6T- R-SR0T-3 R-SR6T-3 R-SRT-3 R-SRT-3 R-SRT-3 R-SRT- Model No. R-CH0T R-CH4T R-CH6T R-CH0T R-CH6T R-CHT R-CHT R-CHT R-CHT R-CHS R-CHS R-CHS 7.30.38 4.9 30.00 37.6 47.78 55. 68.0 80.80 For long locking lever header RoHS compliance Note:. Color: lack Note:. When ordering or only, refer to the above Note:. Model Nos. 6. 7.0 3.4 For short locking lever header 6. 7.0 3.4 4
R CONNECTOR Shrouded header With long locking lever With short locking lever Side entry type Specifications Characteristics Materials and Finish Current rating Voltage rating Temperature range.0 C, DC 300V C, DC (including temperature rise in applying electrical current) -55 C to+ C(gold-plated) -55 C to+05 C(tin-plated) Post rass Nickel-undercoated Mating part; gold-plated Solder tail; tin-plated (reflow treatment) Copper-undercoated, tin-plated (reflow treatment) Insulation resistance Withstanding voltage 5,000M Ω min. 0V C/5 seconds Housing Glass-filled PT, UL94V-0, black pplicable PC board thickness.6mm Note: Contact JST for details. 5
R CONNECTOR Model number identification R H TD 0 Series name Product name: Header Number of circuits: 0, 4, 6, 0, 6,,,, Number of guide grooves: 0 to circuits... and circuits..., PC board mounting method TD...Top entry SD...Side entry Type of locking lever: 0...Without locking lever...long locking lever...short locking lever Post material:...rass Surface finish: 0...Gold-plated (flash)...0.micron gold-plated 3...0.4micron gold-plated 4...0.76micron gold-plated 90...Tin-plated (reflow treatment) Note: The standard gold-plated type is identified by the suffix number [-0], but this suffix number is usually omitted. Other types must be identified by the full code number. Special types do not conform to the coding system in the left. Long locking lever Short locking lever Side entry type 5.4 Long locking lever Short locking lever 5.4 Polarizing mark 3.6.54.54 8.94 7.5 3.0 (7.95) 4. 8.8max. (when unlocked) 5.85.54.0 8.9 3.0 (3.05) 7.5 0.5 8.94.54 0 4 6 0 6 Type of locking lever No.of guide grooves Gold-plated header (With locking lever) Model No. Tin-plated header (With locking lever) Side entry type Side entry type R-H0TD R-H0SD R-H0TD-90 R-H0SD-90 R-H4TD R-H4SD R-H4TD-90 R-H4SD-90 R-H6TD R-H6SD R-H6TD-90 R-H6SD-90 R-H0TD R-H0SD R-H0TD-90 R-H0SD-90 R-H6TD R-H6SD R-H6TD-90 R-H6SD-90 *R-HTD-0 R-HTD R-HSD R-HTD-90 R-HSD-90 *R-HTD-0 R-HTD R-HSD R-HTD-90 R-HSD-90 *R-HTD-0 *R-HTD *R-HSD *R-HTD-90 *R-HSD-90 R-HTD R-HSD R-HTD-90 R-HSD-90 *R-HTD-0 *R-HTD *R-HSD *R-HTD-90 *R-HSD-90 R-HTD R-HSD R-HTD-90 R-HSD-90 RoHS compliance This product displays (LF)(SN) on a label. Note:.Headers with locking levers can be used only for receptacle with strain reliefs..*marked products are not CS approved. 0.6 3.6 5.4 37.6 7.78 39.78.86 44.86 30.48 5.48.64 6.64 48.6 70.6.96 8.96 73.66 95.66 Q'ty / box 6
R CONNECTOR PC board layout (viewed from component side) Side entry type +0..0 0.05 <Note 3>.54±0.05.5.7 <Note > (Mounting screw hole).54±0.05 <Note 3> +0..0 0.05 0.74.7 <Note > (Mounting screw hole).54±0.05 H 8.90±0. (4.0).54±0.05-5.85±0. (Edge of PC oard) S 0 4 6 0 H 0.6 5.4 7.78.86 S.86 6.94 9.48.56 Note:. Tolerances are non-cumulative: ±0.05mm for all centers. Hole dimensions differ according to the kind of PC board and piercing method. The dimensions above should serve as a guideline. Contact JST for details.. The mounting screw holes are not required for standard headers. 3. This is normally No. pin position. 6 30.48 4.8.64 5. 48.6 59.96.96 7.66 73.66 85.36 7