Parts List For RIDGID " Compound Miter Saw Model MS0 Figure 0 0 0 0
Parts List For RIDGID " Compound Miter Saw Model MS0 Figure Always order by part number - not by key number 0 0 0-0- 0-0 -0 0 0 00 Fence Sliding Screw Soc Cap /- x *Washer x x. Knob Fence *ScrewPanHdMx.0x Fence Stationary *Screw Pan Hd. M x 0.- Plate Throat Table Shaft Bevel Pivot Indicator Bevel Stop Bevel Index *Screw Soc Cap /- x / Screw Soc Set Lock M x.- Shoe Left Plate Guard Screw Sems M-0 Shoe Base Rear Base Washer Spring. x x 0. Washer.0 x x / * Standard Hardware Item - May be purchased locally. 0 0 0 0-00- 0-0 0 0-0 0 - SP 00 Bolt Table Pivot Arm Miter *Lockwasher Int. Tooth /" *Screw Soc Cap /- x / Screw Set Lock M x.0- Knob Miter Screw Sems M- Plate Clamp Miter Shoe Base Front Grip Miter Index Spring Miter Index * Washer x x. Grommet Wrench Shoe Right Indicator Miter Wrench Hex L / Table Extension Clamp Screw Sems M- Owners Manual Bag Asm Ext. Hardware (Not Illustrated)
Parts List For RIDGID " Compound Miter Saw Model MS0 Figure Upper and Lower Guards 0 To remove this item use a mm hex L wrench 0 n 0 0
Parts List For RIDGID " Compound Miter Saw Model MS0 Figure Upper and Lower Guards Always order by part number - Not by key number 0 0 0 0-0 0-0 0 0 00- - Screw Arbor Washer Blade Collar Blade Blade Screw Sems M - Screw Shoulder 0- x /" Sleeve Rubber Lock Arbor Cap Grip Spring Arm Guard Upper Plate Retainer Arbor Lock Screw Flat Hd M x 0.- Grommet Arbor Lock Bag Dust Elbow Screw Soc. Set Lock M x.0- Chute Sawdust Screw Sems M- *ScrewPanHdMx0.- * Standard Hardware Item - May Be Purchased Locally. CAUTION: See Mechanical Assembly Caution below. WARNING: Uncontrolled spring release of misinstallation of these parts may create a Hazard unless repair is done by a qualified service technician. CAUTION: Mechanical Assembly, to qualified service technician.. Wear approved eye protection when working with coil springs including spring, arbor lock 0.. Incorrect re-assembly of torsion spring 0 can cause an unsafe condition because cutting head fails to rise fully to stop, or because spring fails through over-stress.. Improper reassembly of mechanisms controlling movement of lower guard can cause an unsafe condition because guard fails to operate freely as cutting head is moved up and down. 0 0 0 0- - - 0-0- 0-0 0- - 0-0 0-0-0 Bumper Lower Guard * Washer. x. x. Bearing Screw Shoulder M- Nut Hex Lock M x.0 * Washer. x x 0. Link Actuator Spacer x 0 x Washer. x x 0. Retainer Guard Guard Lower Spring Guard Screw Shoulder 0-x.0 Pivot Lower Guard Nut Hex Lock M x.0 *ScrewPanHd0-x/ Retainer Bearing * Screw Flat Hd M x.0- * Washer. x x 0. Screw Shoulder M x 0.- Washer / x x
Parts List For RIDGID " Compound Miter Saw Model MS0 Figure - Handle and Motor Assembly 0 0
Parts List For RIDGID " Compound Miter Saw Model MS0 Figure - Handle and Motor Assembly Always order by Part Number - Not by Number No 0 0 0-0 0-0 0 0 Screw Pan Hd Ty E M-0 Handle Carry *Screw Pan Hd Ty TT Mx0.-0 Screw Pan Hd Ty E M- Handle Upper Actuator Switch Clamp Cord Guard Cord Cord w/plug Handle Lower Motor Brush Cover Brush * Standard hardware item - May be purchased locally. WARNING: Any attempt to repair or replace electrical parts on this unit may create a hazard unless repair is done by a qualified service technician. WARNING: For your safety, this miter saw is specially insulated. To reduce the risk of electrical shock, fire or injury, use only parts identical to those identified in the parts list. Reassemble exactly as originally assembled. 0 0-0- 0-0 00 0-00- Cover Rear Motor Bearing Needle Spindle Asm Retainer Bearing *Screw Pan M x 0.- Screw Pan Hd Ty TT Mx0.-0 *Lockwasher M *Washer x x 0. Button Lock Spring Torsion Switch Screw Pan Hd Ty E M-0 *Connector Wire # #
Parts List For RIDGID " Compound Miter Saw Model MS0 Figure - Pivot Assembly o 0 Always order by Part Number - Not by Number 0 0 0 0-0 0-0 0- Spring Torsion Spacer Torsion Spring Shaft Arm Pivot Cap Rubber Ring O Pin Locking Pivot Screw Set Lock M x 0.- *Washer x x 0. Washer. x x * Standard hardware item - May be purchased locally. n To remove this item use a mm hex L wrench. oto remove this item use a mm hex L wrench. CAUTION: See mechanical assembly caution on page. - - 0 00 0-0 Washer Spring. x x 0. Nut Lock M x. Knob Bevel Screw Shoulder M x Ball mm Spring Screw Set Lock M x.0-0 Pin Bevel Index * Washer 0 x 0 x 0
Parts List For RIDGID " Compound Miter Saw Model MS0 Figure - Legset 0 Always order by Part Number - Not by Number 0 0- Short Upper Stiffener Long Upper Stiffener Nut Hex Flanged /- Carriage Bolt /- x / Leg Foot * Standard hardware item - May be purchased locally. Items Not Illustrated 0 0- Short Lower Stiffener Long lower Stiffener Screw Hex Hd /- x -/ Washer Bag Asm (Leg Set Hardware)