1 Sol-Ark 8K SOLAR GENERATOR Quick Start Guide 2018 972-575-8875 sales@portablesolarllc.com www.portablesolarllc.com

2 Solar Panel Installation 1. Sol-Ark 8K has 2 separate pairs of solar panel inputs. 2. Use the chart to the right to determine how many strings of panels and how many panels per string can be installed. 3. Never exceed the Max PV input: 10,000W per system (5,000W per MPPT) PV = 500Voc Max 4. Connect the stings of solar panels to the system as shown on page 4. 5. Each pair of strings, PV1A/B and PV2A/B, must be the same voltage if both are used (see chart). Solar Panel String Guide ( 60 or 72 cell Panels) Total Panels PV1A PV1B PV2A PV2B 1 N/A N/A N/A N/A 2 N/A N/A N/A N/A 3 N/A N/A N/A N/A 4 N/A N/A N/A N/A 5 5 N/A N/A N/A 6 6 N/A N/A N/A 7 7 N/A N/A N/A 8 8 N/A N/A N/A 9 9 N/A N/A N/A 10 5 5 N/A N/A 11 6 N/A 5 N/A 12 6 6 N/A N/A 13 7 N/A 6 N/A 14 7 7 N/A N/A 15 5 5 5 N/A 16 8 8 N/A N/A 17 6 6 5 N/A 18 6 6 6 N/A 19 6 6 7 N/A 20 7 7 6 N/A 21 7 7 7 N/A 22 7 7 8 N/A 23 8 8 7 N/A 24 8 8 8 N/A 25 8 8 9 N/A 26 8 8 5 5 27 N/A N/A N/A N/A 28 8 8 6 6 29 N/A N/A N/A N/A 30 8 8 7 7 31 N/A N/A N/A N/A 32 8 8 8 8

7.48 7.48 3 Transfer Switch Install your transfer switch Note: GFI breakers connected to transfer switch will trip when on Gen position. Replace with Non-GFI breaker. A GFI receptacle can be installed on circuit after transfer switch. Mount Sol-Ark Find a suitable location for the system, keeping in mind the dimensions shown here. You may need to affx a mounting board to your wall first using 6-8 screws into studs. Then using 6 screws 17.87 apart mount Sol-Ark 8K to the board/wall 6 minimum clearance 6 17.87 Connect Batteries (w/ Cables & Boot Covers) Do not Reverse Polarity of Batteries

4

5 Sol-Ark 8K Preliminary Specifications (subject to change) Solar Max allowed PV Power Max allowed PV Power per MPPT Max DC voltage 10000W 5000W 500V MPPT voltage range 150-425V Starting voltage Number of MPPT 2 Solar Strings per MPPT 2 Max DC current per MPPT AC Output Connections 175V 18A 120/240V split phase 8000W 33A L-L (240V) Continuous AC power on Solar or Battery Surge AC power 10sec Frequency 4000W 33A L-N (120V) 12000VA L-L (240V) 6000VA L-N (120V) 60/50Hz 12000W 50A L-L (240V) Continuous AC power with Grid or Generator 6000W 50A L-N (120V) Peak Effciency 96.0% CEC Effciency 95.0% Idle Consumption typical no load Sell back power modes Design Response Time (Grid-Tied to Off-Grid) Battery (optional) Type Nominal DC Input Capacity 60W Limited to Household or Full Grid-Tied Transformerless 15ms Lead-Acid or Li-Ion 48V 90 1000Ah Voltage Range 40.0 61.0V Continuous Battery charging output Charging curve External temperature sensor Current shunt for accurate % SOC External Generator Start based on voltage or % SOC Communication to Lithium battery General 185A 3-stage w/ equalization optional CanBus Dimensions (H x W x D) 25.6 x 18.8 x 7.1 Weight Mounting Air Cooling Display Wi-Fi Communication (monitoring or SW updates) Snap on sensors for limited selling to Household Standard Warranty Optional Extended Warranty 75 lbs Wall 4 variable speed fans Color touch screen included 5 years 10 years Protection & Certifications (UL approvals June 2018) Electronics certified safety by UL or ETL or SGS labs NEC 690.4B & NEC 705.4/6 Grid Sell Back UL1741 SA, Calif Rule 21, IEEE1547, FCC 15 class B PV DC disconnect switch NEC 240.15 Ground Fault Detection NEC 690.5 PV rapid shutdown control NEC 690.12 PV Arc Fault detection NEC 690.11/UL1699B PV input lightning protection AC input/output 50A breakers Battery overcurrent fuse User wiring enclosure w/ ¾ knock-outs Solar Flare/EMP Hardened to 2015 MIL-STD- 461G AND MIL-STD-188-125-1 (Independently tested April 2018) Yes Yes optional 972-575-8875 sales@portablesolarllc.com www.portablesolarllc.com

6 Upgrade to Sol-Ark 8K from Sol-Ark 3K Overview This is a general overview for the process of upgrading to a Sol-Ark 8K from the Sol-Ark 3K. More specific instructions will follow as the release date of the new unit approaches. When you decide to upgrade your system you will need to send us your current Sol-Ark unit, for which we will credit you the amount the you paid for your unit and apply it towards the price of the new Sol-Ark 8K. You will be able to keep and use your current batteries and solar panels as they are compatible with Sol-Ark 8K. Example: Purchased original Sol-Ark with EMP hardening for $4900 and want to swap it out for an EMP hardened Sol-Ark 8K which costs $7200. You would send us your current system and we would put the $4900 towards the Sol-Ark 8K. The price you would pay for the upgrade would be $2300 ($7,200 - $4900 = $2300). So the total cost of upgrade in this example would be $2300 plus shipping. Shipping in most cases will be about $100 to ship the old system to us (includes the packaging cost) and then about $200 for us to send you the new unit. Shipping will be added to your invoice and then we will send you a pre-paid shipping label. If you would like to add additional solar panels, batteries, wire, transfer switch(s), etc.. to your upgrade order, we will adjust your total cost accordingly. How to upgrade to Sol-Ark 8K from Sol-Ark 3K Power down Sol-Ark 3K Unplug Sol-Ark from grid and transfer switch Disconnect the batteries from Sol-Ark 3K but leave them wired to 48V (unless you are upgrading to more than 16 batteries) If you are upgrading to more than 16 batteries you will need to change some of your battery cables (let us know when you order) Remove Sol-Ark 3K Rewire your solar panels in accordance with page 2. Install 2-pole 50A breaker in your breaker box (these will replace the 30A outlet as the grid input) Install Sol-Ark 8K (refer to diagram on page 4) More detailed Sol-Ark 8K install guide is coming soon