Pressure relief valve, pilot-operated Type ZDB and ZDB RE 575 Edition: 06- Replaces: 0.05 Size 6 Component series 4X Maximum operating pressure 35 bar Maximum flow 60 l/min H7746 Features Sandwich plate valve Porting pattern according to ISO 440-03-0-0-05 (with or without locating hole) 4 pressure ratings 5 directions of action, optional or pressure valve cartridges 4 adjustment types for pressure adjustment, optionally Rotary knob Bushing with hexagon and protective cap Lockable rotary knob with scale Rotary knob with scale Corrosion-protected design Contents Features Ordering code Symbols 3 Function, section 4 Technical data 5 Characteristic curves 6 Dimensions 7 0 Accessories 0 Further information 0 RE 575, edition: 06-, Bosch Rexroth AG
/0 ZDB; ZDB Pressure relief valve Ordering code 0 0 03 04 05 06 07 08 09 0 Z DB 6 4X / V * 0 Sandwich plate Z 0 pressure valve cartridge (only with version "VA", "VB" and "VP") no code pressure valve cartridges (only with version "VC" and "VD") 03 Pressure relief valve DB 04 Size 6 6 Relief function from to: 05 A T VA P T VP B T VB A T and B T VC A B and B A VD Adjustment type for pressure adjustment 06 Rotary knob Bushing with hexagon and protective cap Lockable rotary knob with scale 3 ) Rotary knob with scale 7 07 Component series 40 49 (40 49: unchanged installation and mounting dimensions) 4X Pressure rating 08 Set pressure up to 50 bar 50 Set pressure up to 00 bar 00 Set pressure up to 00 bar 00 Set pressure up to 35 bar 35 Corrosion resistance 09 None no code Improved corrosion protection (40 h salt spray test according to EN ISO 97) J3 ) High corrosion protection (70 h salt spray test according to EN ISO 97) J5 ) Seal material 0 NBR seals no code FKM seals V Observe compatibility of seals with hydraulic fluid used. (Other seals upon request) Without locating hole no code With locating hole /60 3) Further details in the plain text * ) H-key with material no. R90000858 is included in the scope of delivery ) Only with adjustment type "", however without protective cap 3) Locking pin ISO 875-3x8-St, material no. R900005694 (separate order) Notice: Preferred types and standard units are contained in the EPS (standard price list). Bosch Rexroth AG, RE 575, edition: 06-
Pressure relief valve ZDB; ZDB 3/0 Symbols ( = component side, = plate side) Type ZDB 6 VA... Type ZDB 6 VB... P A B T P A B T Type ZDB 6 VP... P A B T Type ZDB 6 VC... Type ZDB 6 VD... P A B T P A B T RE 575, edition: 06-, Bosch Rexroth AG
4/0 ZDB; ZDB Pressure relief valve Function, section Pressure valves of type ZDB and ZDB are pilot-operated pressure relief valves in sandwich plate design. They are used for limiting a system pressure. The valves basically consist of the housing (7) and one or two pressure valve cartridges. The system pressure can be set via the adjustment type (4). Example version "VA": In the initial position the valves are closed. The pressure in channel A acts on the spool (). At the same time, pressure is applied to the spring-loaded side of the spool () via nozzle () and to the pilot poppet (6) via nozzle (3). If the pressure in channel A exceeds the value set at the spring (5), the pilot poppet (6) opens. Hydraulic fluid flows from the spring-loaded side of the spool (), nozzle (3), channel (8) into channel T. The resulting pressure drop moves the spool () and thus opens the connection A to T while maintaining the pressure set at spring (5). The pilot oil drain from the two spring chambers is effected externally, via channel T. 4 5 6 3 8 7 A T P B Type ZDB 6 VA-... A T P B = component side = plate side Bosch Rexroth AG, RE 575, edition: 06-
Pressure relief valve ZDB; ZDB 5/0 Technical data (For applications outside these parameters, please consult us!) general Weight Type ZDB kg Approx. Type ZDB kg Approx.. Any Installation position Ambient temperature range C 0 +80 hydraulic Maximum operating pressure bar 35 Maximum set pressure bar 50; 00; 00; 35 Maximum counter pressure bar 35 (observe the maximum tank pressure of the subplate-mounted valve/directional valve) Maximum flow l/min 60 Hydraulic fluid See table below Hydraulic fluid temperature range C 0 +80 Viscosity range mm /s 0 800 Maximum admissible degree of contamination of the hydraulic fluid Class 0/8/5 ) cleanliness class according to ISO 4406 (c) Hydraulic fluid Classification Suitable sealing Standards Data sheet materials Mineral oils HL, HLP NBR, FKM DIN 554 900 Bio-degradable ) Insoluble in water HETG FKM ISO 5380 HEES FKM 90 Soluble in water HEPG FKM ISO 5380 Flame-resistant Water-free HFDU (glycol base) FKM HFDU (ester base) ) FKM ISO 9 90 HFDR FKM Containing water HFC (Fuchs Hydrotherm 46M, NBR Petrofer Ultra Safe 60) ISO 9 903 Important information on hydraulic fluids: Flame-resistant containing water: For further information and data on the use of other hydraulic Maximum pressure differential 0 bar, otherwise, increased fluids, please refer to the data sheets above or contact us. cavitation erosion There may be limitations regarding the technical valve data Life cycle as compared to operation with mineral oil HL, HLP (temperature, pressure range, life cycle, maintenance intervals, etc.). 30 00% The ignition temperature of the hydraulic fluid used must be 50 K Maximum hydraulic fluid temperature 60 C higher than the maximum solenoid surface temperature. Bio-degradable and flame-resistant: If this hydraulic fluid is used, small amounts of dissolved zinc may get into the hydraulic system. ) The cleanliness classes specified for the components must be adhered to in hydraulic systems. Effective filtration prevents faults and simultaneously increases the life cycle of the components. For the selection of the filters, see www.boschrexroth.com/filter. ) Not recommended for corrosion-protected versions "J3" and "J5" (contains zinc) RE 575, edition: 06-, Bosch Rexroth AG
6/0 ZDB; ZDB Pressure relief valve Characteristic curves (measured with HLP46, ϑ oil = 40 ±5 C) 350 p E q V characteristic curves 30 p E min q V characteristic curves Set pressure in bar 300 50 00 50 00 50 Minimum set pressure in bar 5 0 5 0 5 3 4 0 0 0 0 30 40 50 60 Flow in l/min 0 0 0 0 30 40 50 60 Flow in l/min Notice: The characteristic curves apply to the pressure at the valve output p = 0 bar across the entire flow range. VD (A to B) VA 3 VB, VC 4 VP, VD Bosch Rexroth AG, RE 575, edition: 06-
3 Pressure relief valve ZDB; ZDB 7/0 Dimensions: Type ZDB 6 VA... (dimensions in mm) 6 4 5 3 8 87 96, 5 0 9 6 Ø3 8 40 63 0 Ø30 7 8 57,5 4 F T F 6,75 Ø30 35 A B 44, 5 F4 P G F3 9 3 33 4 x Ø5, 4 Name plate Adjustment type "" 3 Adjustment type "" (with version "J3" and "J5" without protective cap) 4 Adjustment type "3" 5 Adjustment type "7" 6 Dimensions required to remove the key 7 Valve mounting bores 8 Lock nut SW4, tightening torque M A = 0 +5 Nm 9 Hexagon SW0 0 Identical seal rings for ports A, B, P, T (plate side) Hexagon SW4, tightening torque M A = 50 Nm plate side porting pattern according to DIN 4340 form A (without locating hole), or ISO 440-03-0-0-05 (with locating hole Ø3 x 5 mm deep for locking pin ISO 875-3x8-St, material no. R900005694, separate order) 3 component side porting pattern according to DIN 4340 form A (without locating hole), or ISO 440-03-0-0-95 (with locating hole Ø4 x 4 mm deep) 0,0/00 Rzmax 4 Required surface quality of the valve contact surface Valve mounting screws see page 0. RE 575, edition: 06-, Bosch Rexroth AG
0 9 8 3 8/0 ZDB; ZDB Pressure relief valve Dimensions: Type ZDB 6 VB... and type ZDB 6 VP... (dimensions in mm) 3 5 4 6 98 88, 5, 5 8 4 40 Ø3 0 63 7 Ø30 84 6,75,5 F T F 8 44, 5 A B 35 Ø30 F4 P G F3 4 x Ø5, 4 33 57 3 9 Name plate Adjustment type "" 3 Adjustment type "" (with version "J3" and "J5" without protective cap) 4 Adjustment type "3" 5 Adjustment type "7" 6 Dimensions required to remove the key 7 Valve mounting bores 8 Lock nut SW4, tightening torque M A = 0 +5 Nm 9 Hexagon SW0 0 Identical seal rings for ports A, B, P, T (plate side) Hexagon SW4, tightening torque M A = 50 Nm plate side porting pattern according to DIN 4340 form A (without locating hole), or ISO 440-03-0-0-05 (with locating hole Ø3 x 5 mm deep for locking pin ISO 875-3x8-St, material no. R900005694, separate order) 3 component side porting pattern according to DIN 4340 form A (without locating hole), or ISO 440-03-0-0-95 (with locating hole Ø4 x 4 mm deep) 0,0/00 Rzmax 4 Required surface quality of the valve contact surface Valve mounting screws see page 0. Bosch Rexroth AG, RE 575, edition: 06-
0 9 8 3 Pressure relief valve ZDB; ZDB 9/0 Dimensions: Type ZDB 6 VC... and type ZDB 6 VD... (dimensions in mm) 6 5 3 5 6 8 94 8 90, 5 3 90, 5 3 0 9 8 0 3,5 40 Ø3 4, 5 4, 5 4 8 4. 4. 0 4 39 3 9 63 4 4 x Ø5, 4 5 63 7 Ø30 44, 5 35 6,75 F F4 A P T G B F F3 Ø30 35 8 57 3, 5,5 57,5 7 Name plate Adjustment type "" 3 Adjustment type "" (with version "J3" and "J5" without protective cap) 4 Adjustment type "3" 5 Adjustment type "7" 6 Dimensions required to remove the key 7 Valve mounting bores 8 Lock nut SW4, tightening torque M A = 0 +5 Nm 9 Hexagon SW0 0 Identical seal rings for ports A, B, P, T (plate side) Hexagon SW4, tightening torque M A = 50 Nm plate side porting pattern according to DIN 4340 form A (without locating hole), or ISO 440-03-0-0-05 (with locating hole Ø3 x 5 mm deep for locking pin ISO 875-3x8-St, material no. R900005694, separate order) 3 component side porting pattern according to DIN 4340 form A (without locating hole), or ISO 440-03-0-0-95 (with locating hole Ø4 x 4 mm deep) 4. Version "VC" 4. Version "VD" 0,0/00 Rzmax 4 Required surface quality of the valve contact surface Valve mounting screws see page 0. RE 575, edition: 06-, Bosch Rexroth AG
0/0 ZDB; ZDB Pressure relief valve Dimensions Valve mounting screws (separate order) Version "J3" 4 hexagon socket head cap screws ISO 476 - M5-0.9-CM-Fe-ZnNi-5-Cn-T0-H-B friction coefficient µ total = 0.09 0.4; tightening torque M A = 7.4 Nm ±0 % Version "J5" 4 hexagon socket head cap screws ISO 476 - M5-0.9-CM-Fe-ZnNi-8-Cn-T0-H-B friction coefficient µ total = 0.09 0.4; tightening torque M A = 7.4 Nm ±0 % Without corrosion protection 4 hexagon socket head cap screws ISO 476 - M5-0.9 with friction coefficient µ total = 0. 0.7; tightening torque M A = 8. Nm ±0 % Accessories (separate order) Denomination Protective cap Material no. R90069658 Further information Pressure relief valve, pilot-operated Data sheet 573 Hydraulic fluids on mineral oil basis Data sheet 900 Environmentally compatible hydraulic fluids Data sheet 90 Flame-resistant, water-free hydraulic fluids Data sheet 90 Flame-resistant hydraulic fluids - containing water (HFAE, HFAS, HFB, HFC) Data sheet 903 Use of non-electrical hydraulic components in an explosive environment (ATEX) Data sheet 070 Hydraulic valves for industrial applications Operating instructions 07600-B Selection of the filters www.boschrexroth.com/filter Bosch Rexroth AG Hydraulics Zum Eisengießer 9786 Lohr am Main, Germany Phone +49 (0) 93 5 / 8-0 documentation@boschrexroth.de www.boschrexroth.de This document, as well as the data, specifications and other information set forth in it, are the exclusive property of Bosch Rexroth AG. It may not be reproduced or given to third parties without its consent. The data specified above only serve to describe the product. No statements concerning a certain condition or suitability for a certain application can be derived from our information. The information given does not release the user from the obligation of own judgment and verification. It must be remembered that our products are subject to a natural process of wear and aging. Bosch Rexroth AG, RE 575, edition: 06-
Pressure relief valve ZDB; ZDB /0 Notes Bosch Rexroth AG Hydraulics Zum Eisengießer 9786 Lohr am Main, Germany Phone +49 (0) 93 5 / 8-0 documentation@boschrexroth.de www.boschrexroth.de This document, as well as the data, specifications and other information set forth in it, are the exclusive property of Bosch Rexroth AG. It may not be reproduced or given to third parties without its consent. The data specified above only serve to describe the product. No statements concerning a certain condition or suitability for a certain application can be derived from our information. The information given does not release the user from the obligation of own judgment and verification. It must be remembered that our products are subject to a natural process of wear and aging. RE 575, edition: 06-, Bosch Rexroth AG
/0 ZDB; ZDB Pressure relief valve Notes Bosch Rexroth AG Hydraulics Zum Eisengießer 9786 Lohr am Main, Germany Phone +49 (0) 93 5 / 8-0 documentation@boschrexroth.de www.boschrexroth.de This document, as well as the data, specifications and other information set forth in it, are the exclusive property of Bosch Rexroth AG. It may not be reproduced or given to third parties without its consent. The data specified above only serve to describe the product. No statements concerning a certain condition or suitability for a certain application can be derived from our information. The information given does not release the user from the obligation of own judgment and verification. It must be remembered that our products are subject to a natural process of wear and aging. Bosch Rexroth AG, RE 575, edition: 06-