Size of Mattress and oundation The length and width of the upper and lower bunk mattress and foundation are as follows : Size Twin ull Length 74-75 74-75 Width 37 ½ - 38 ½ 52-53 Thickness 9 ½ max 9 ½ max You must use only this size mattress. nsure thickness of upper and lower mattress and foundation combined does not exceed 9 ½ and that the mattress is at least 5 below upper edge of guardrails. This unk ed uses a slat kit for mattress foundation. Replacement Parts Replacement parts, including additional guardrails, may be obtained from any dealer STY WRNINGS!! ( 1 ) ( 2 ) ( 3 ) ( 4 ) ( 5 ) ( 6 ) ( 7 ) ( 8 ) ( 9 ) (10) (11) (12) (13) ollow the information on the warnings appearing on the upper bunk end structure and on the carton. o not remove warning label from bed. lways use the recommended size mattresses or mattress support, or both, to help prevent the likehood of entrapment or falls. Surface of mattress must be at least 5 in. (127mm) below the upper edge of guardrails. o not allow children under 6 years of age to use the upper bunk. Periodically check and ensure that the guardrail, ladder, and other component are in their proper position, free from damage, and that all connectors are tight. o not allow horseplay on or under the bed and prohibit jumping on the bed. lways use ladder for entering or leaving upper bunk. o not use substitute parts. ontact the manufacturer or dealer for replacement parts. Use of a night light may provide added safety precaution for a child using the upper bunk. lways use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to the wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent entrapment between the bed and the wall. The use of water or sleep flotation mattresses is prohibited. STRNGULTION HZR : Never attach or hang items to any part of the bunk bed that are not designed for use with the bed; for example, but not limited to, hooks, belts and jump ropes. Keep these instructions for future reference. UNK STY WRNING Page 1 of 8
RY UNK SSMLY INSTRUTIONS (TWIN - TWIN) (TWIN - ULL) (ULL - ULL) Thank you for choosing unk ed.this practical design offers the utmost in versatility. efore assembling your bunk bed, please read through theseinstructions carefully. amiliarize yourself with the different parts. Please note that you will require a and an llen wrench. dult ssembly llen wrench ustomer Supplied TWIN OVR ULL SHOWN GURRIL N ST UP T ITHR N O TH UNK TWIN / TWIN HRWR ULL / ULL NOT: W INLU SPR HRWR IN S TH LLN WRNH, J, RRL NUT, WOO SRW OR WOO UTTON R MG URING SSMLY. J M6 X 3 ½ (90mm) - 16 pcs Spare - 2 pcs 1 Wood Screw - 4 pcs Spare - 2 pcs J M6 X 2 (50mm) - 4 pcs Spare - 2 pcs Metal Pins - 4 pcs Wood utton - 8 pcs Spare - 1 pc arrel Nut - 20 pcs Spare - 2 pcs UNK Page 2 of 8 G llen wrench - 1 pc Spare - 1 pc
PRTS LIST TWIN OVR ULL SHOWN 04 05 09 10 01 01 04 05 09 10 HRWR UPPR PNL LOWR PNL ULL GUR RIL 3/4 GUR RIL LT N PS RIGHT N PS LONG RIL TWIN SLT KIT OR ULL UPPR UNK SLT KIT ULL LOWR UNK SLT KIT OR TWIN LOWR UNK SLT KIT UNK Page 3 of 8
STP 1 ttach the long rails () to the upper panels (), using J M6 X 3 ½ (), and barrel nut (). Tighten with the llen wrench (G). J M6 X 3 ½ arrel Nut G llen wrench dult ssembly STP 2 If the bunk bed will be placed next to a wall, the guard rail that runs the full length of the bed should be placed against the wall to prevent entrapment between the bed and the wall. 04 dult ssembly 05 J M6 X 2 Note : Screw holes on end caps go on inside of guard rails. arrel Nut G UNK ttach the full guard rail (04) to the end caps ()(), using J M6 X 2 (), and barrel nut (). Tighten with the llen wrench (G). Repeat for 3/4 guard rail (05). llen wrench Page 4 of 8
STP 3 Lay the twin slat kit (09) onto the bed. ix in place using wood screws provided in the slat kit box. OR SLT KIT SSMLY follow assembly instructions included with slat kit. 09 dult ssembly ustomer Supplied Twin size shown ull Upper panel uses ull upper slat kit STP 4 Install the full and 3/4 guard rail assemblies onto the long rails, and fix in place using wood screws (). Tighten with the.(ustomer Supplied) ULL GUR RIL SSMLY dult ssembly 1 Wood Screw 3/4 GUR RIL ustomer Supplied GURRIL N ST UP T ITHR N O TH UNK UNK Page 5 of 8
STP 5 ttach the long rails () to the lower panel (), using J M6 X 3 ½ (), and barrel nut (). Tighten with the llen wrench (G). J M6 X 3 ½ arrel Nut G llen wrench dult ssembly STP 6 Lay the slat kit with center support (10) onto the bed, and fix in place using wood screws provided in the slat kit box. OR SLT KIT SSMLY follow assembly instuctions included with slat kit. 10 dult ssembly ustomer Supplied ull size shown Twin lower panel uses Twin slat kit UNK Page 6 of 8
STP 7 Insert metal pins () into the holes in top of the lower panels. Lift the upper panels onto the lower panels as shown, and fit the metal pins into the holes in the bottom of the upper panel legs. TWIN-TWIN dult ssembly Metal Pins TWIN-ULL UTION! This step requires two strong people. ULL-ULL STP 8 over holes with wood buttons ()(Twin ull, ull ull ). dult ssembly Wood utton ustomer Supplied Lastly, install Ladder. TWIN OVR ULL SHOWN OR LR SSMLY, PLS OLLOW SSMLY INSTRUTIONS INLU WITH YOUR LR. UNK ongratulations! Your bunk bed is now ready for use. We recommend that you double check that all screws are tight, and that all parts are secure before use and periodically check that all screws are tight to ensure lasting Safety. Page 7 of 8
STP 9 ONVRSION TO 2 TWIN OR 2 ULL S. isassemble upper bunk by removing guard rails. lso remove metal pin from lower bunk. Metal Pin UPPR UNK LOWR UNK isassemble upper bunk by removing upper panel () and lower bunk by removing lower panel(). xchange upper panel to the lower panel position and Install hardware tighten with llen wrench. UPPR UNK LOWR UNK STP 10 Use Wood button () to cover holes as shown. TWO TWIN S TWO ULL S UNK Page 8 of 8