Endsuction Pumps Vogel Series LS, LC, LCP
Design LS Technical Data Performance Range: m Capacity up to 4600m 3 /h (20.250 USgpm) m Head up to 170m (560 feet) m Speed up to 1750 rpm Sizes: m DN 125 up to DN 600 (5 up to 24 ) discharge, m Size DN 32 up to DN 150 (1 1/4 up to 6 ), refer to design LSN Temperature: m max. 180 C (350 F) Casing pressure: m up to 16bar (174/230 psig) For higher casing pressures refer to design LC/LCP Handled liquids: m Clean or slightly contaminated liquids (without bigger solids) m Cold and hot water m Condensate and deiomized water m Oil brine and acid m Paper stock suspensions up to 1,2% Applications: m General industry m Chemical industry m Steel mills and mining m Sugar industry m Pulp and paper mills Materials: Code Impeller Casing, Casing cover Wear rings Bearing frame Shaft Shaft sleeve NL 0.6025 SL Bronze CC480 K Ductile iron 0.7040 VL NF SF 1.4408 0.6025 Bronze CC480 K Carbon steel 1.0619 0.6025 0.6025 Stainless steel 1.4021 1.4021 VF 1.4408 VV WW 1.4408 Duplex 1.4517 1.4408 Duplex Duplex 1.4517 1.4462/ 1.4517 Duplex 1.4462 Other materials upon request
Performance Range 1450rpm, 950rpm, 750rpm Capacity Förderstrom Total head [m] LSN Total Förderhöhe head [ft] [ft] Förderstrom Capacity Q Q [m [m 3 /h] 3 /h] Design LSN refer to separate brochure
Design Variations Design LS: Horizontal single stage endsuction pump with closed impeller and oil lubricated bearing frame. Process design, back pull out for easy maintenance. Disassembly of impeller and bearing frame without dismantling of pump casing and motor possible (spacer type coupling required). Suction branch axial, discharge radial upwards (optional horizontal possible). Design LS Drive by electric motor and flexible coupling arranged on common base plate. Design LSV: Vertical design with short shaft for dry installation. Bearing frame with grease lubricated antifriction bearings. Motoradapter welded design, drivers IEC electric motors, design V1 and flexible coupling. Design LT: Vertical line shaft version. Bearing frame and motor above pit for dry installation. Pumpend flooded by the handled liquid. Radial friction bearing lubricated by handled liquid or with external clean water lubrication. Installation length up to 10m. Design LSV Design LT
Design features LS: m Horizontal single stage endsuction pump with closed impeller. m Process design, back pull out for easy and safe maintenance. Disassembly of impeller and bearing frame without dismantling of pump casing and motor possible (spacer type coupling required). m Thrust bearing at drive side (pair of angular contact bearings) for high load capability in both directions, roller bearing at pump side. m Solid shaft dimension for low shaft deflection and heavy duty oil lubricated bearings for continuous operation. m version in dry shaft design, shaft and threads protected by closed impeller nut and shaft sleeve. m Distance between bearings bigger than impeller overhung. m Shaft sealing stuffing box with internal or external flush or cooled stuffing box. Mechanical seals according to EN 12756 (DIN 24960), inner single mechanical seal, double mechanical seals or cartridge seals.
Design LC casing foot mounted Design LCP with centerline casing feet Technical Data Performance Range: m Capacity up to 2800m 3 /h (20250USgpm) m Head up to 100m (330feet) m Speed up to 1750 rpm Sizes: m DN 125 up to DN 400 (5 up to 24 ) discharge, m Size DN 32 up to DN 150 (1 1/4 up to 6 ), refer to design ICP Temperature: m Design LC max. 180 C (350 F) m Design LCP max. 210 C (410 F) Casing pressure: m max. 25bar (360psig) Handled liquids: m Clean and slightly contaminated liquids (without bigger solids) m Cold and hot water m Condensate and deiomized water m Oil brine and acid Applications: m General industry, power stations, district heating m Chemical industry m Sugar mills m Pulp and paper mills Materials: Code Impeller Casing, Casing cover Wear rings Bearing frame Shaft Shaft sleeve NL VL NF VF 0.6025 Sphäroguss 0.7040 1.4408 0.6025 Carbon steel 1.0619 1.4408 0.6025 0.6025 Stainless steel 1.4021 1.4021 VV WW 1.4408 Duplex 1.4517 1.4408 Duplex Duplex 1.4517 1.4462/ 1.4517 Duplex 1.4462 Other materials upon request
Performance Range 1450rpm, 950rpm, 750rpm Capacity Total head [m] Total head [ft] Capacity Q [m 3 /h] Design ICP refer to separate brochure
Design LC: Foot mounted casing design for operating temperatures up to max. 180 C (350 F) / 25bar (360psig). Design LCP: Process design with centerline casing feet for operating temperatures up to max. 210 C (410 F) / 25bar (360psig). Due to the centerline casing feet and the additional support feet a negative influence is avoided on the coupling alignment caused by thermal expansion of the casing at high operating temperatures. At operating temperatures above 180 C (350 F) oil sump cooling of the bearing frames is required.
Design features LC, LCP: m Horizontal single stage endsuction pump with closed impeller. m Design IC with foot mounted casing for operating temperatures up to 180 o C (350 o F). Design LCP with centerline casing feet for operating temperatures up to 210 o C (410 o F). m Process design, back pull out for easy and safe maintenance. Disassembly of impeller and bearing frame without dismantling of pump casing and motor possible (spacer type coupling required). m Thrust bearing at drive side (pair of angular contact bearings) for high load capability in both directions, roller bearing at pump side. m Solid shaft dimension for low shaft deflection and heavy duty oil lubricated bearings for continuous operation. m version in dry shaft design, shaft and threads protected by closed impeller nut and shaft sleeve. m Distance between bearings bigger than impeller overhung. m Shaft sealing stuffing box with internal or external flush or cooled stuffing box. Mechanical seals acc. to EN 12756 (DIN 24960), inner single mechanical seal, double mechanical seals or cartridge seals.
Shaft sealing: Design LS, LC, LCP Stuffing box optional with internal or external flush for temperatures up to 140 C (280 F) Design LS, LC, LCP Stuffing box with cooling jacket for temperatures up to 180 C (350 F) Design LS Single mechanical seal acc. to EN 12756 (DN 24960) unbalanced Design LS, LC, LCP Single mechanical seal acc. to EN 12756 (DN 24960) balanced
Design LS, LC, LCP Cartridge seal, single mechanical seal (Optional with quench or double mechanical seal Design LS, LC, LCP Single balanced mechanical seal in dead end configuration for hot water applications ISO 9001 + 14001 certifications guarantee high quality standards and reliability of our products as well as environmentally friendly production process.
Xylem 1) The tissue in plants that brings water upward from the roots; 2) a leading global water technology company. We re 12,500 people unified in a common purpose: creating innovative solutions to meet our world s water needs. Developing new technologies that will improve the way water is used, conserved, and re-used in the future is central to our work. We move, treat, analyze, and return water to the environment, and we help people use water efficiently, in their homes, buildings, factories and farms. In more than 150 countries, we have strom, long-standing relationships with customers who know us for our powerful combination of leading product brands and applications expertise, backed by a legacy of innovation. For more information on how Xylem can help you, go to xyleminc.com. Xylem Water Solutions Austria GmbH A-2000 Stockerau Ernst Vogel-Straße 2 Tel +43-2266-604 Fax +43-2266-65 311 info.austria@xyleminc.com www.lowara.com Lowara, Flygt and Wedeco are trademarks of Xylem Inc. 2014 Xylem, Inc. Articleno. 771310100 / 11 2014