750L TIER LT/WT/LGP CRAWLER DOZER III CERTIFIED ENGINE Model Case Family IV, 445TA/E66, Tier III certified Cylinders 4 Bore/Stroke 4.1 in x 5.2 in (104 x 132 mm) Displacement 274 in 3 (4.5 L) Fuel injection Fuel Fuel filter Air intake Cooling Direct #2 Diesel Spin-on with in-line strainer Cross-flow Liquid Engine speeds (rpm) High idle - no load 2220+50 Rated - full load 2000 Low idle 800-1050 Horsepower per SAE J1349 Net 84 (62.6 kw) @ 2000 rpm Gross 90 (67.1 kw) @ 2000 rpm Peak torque @ 1400 rpm Net 288 lb ft (391 N m) Gross 295 lb ft (400 N m) Engine lubrication Pump Deep sump plate cooler with pressurized under-piston nozzles Pump operating angle ratings Side-to-side 45 Fore and aft 45 Oil filtration Replaceable, spin-on full-flow cartridge ENGINE COOLING Radiator Core size area 583 in 2 (0.38 m 2 ) Rows of tubes 4 Fan Diameter 21.6 in (550 mm) Ratio 0.875:1 ELECTRICAL SYSTEM Alternator 90 amp Battery 12-volt low-maintenance 700 cold-cranking amps @ 0 F (-18 C) POWERTRAIN Dual path hydrostatic Pump variable axial piston Motor variable bent axis piston Maximum drawbar pull* 40,000 lb (178 kn) Transmission Single lever control electronic straight tracking Oil filter 4 micron, spin-on replaceable Travel speeds* Forward 0-6 mph (0-9.7 km/h) Reverse 0-6 mph (0-9.7 km/h) *Measured using standard track chain. Increase travel speeds by 4% and reduce drawbar pull by 4% with the optional CELT track chain. Parking brakes Steering brakes Final drive Heavy-duty, spring-applied, hydraulic pressure release Hydrostatic 2 helical gear reduction to planetary output Ratio 62:1 TRANSMISSION COOLING Type Oil to water Core size 431 in 2 (.28 m 2 ) HYDRAULIC SYSTEM Standard equipment pump Pump flow @ 2000 rpm @ 3000 psi (209 kpa) Max. system pressure CYLINDERS Lift cylinder (2) Bore diameter Rod diameter Stroke Angle cylinder (2) Bore diameter Rod diameter Stroke Tilt cylinder (1) Bore diameter Rod diameter Stroke Page 1 of 4 20.3 gpm (76.8 L/min) 3025+75 psi (20 855+515 kpa) 3.50 in (89 mm) 1.75 in (44.5 mm) 15.5 in (394 mm) 3.50 in (89 mm) 1.75 in (44.5 mm) 15.5 in (394 mm) 3.50 in (89 mm) 1.75 in (44.5 mm) 5.80 in (144 mm) UNDERCARRIAGE Track adjustment Hydraulic Frame Rigid suspension Length of track on ground 89 in (2266 mm) Track link pitch Track shoe height Pin diameter 6.73 in (171 mm) 2.06 in (52 mm) 1.32 in (33 mm) Bushing diameter CLT track 2.24 in (57 mm) CELT track 3.0 in (76 mm) Bolt diameter 0.625 in (16 mm) Track shoes per side 39 Track rollers per side 6 Carrier rollers per side 1 Track roller rail dia. 7.48 in (190 mm) TRACK ON GROUND Shoe Area in 2 (cm 2 ) 18 in (457 mm) 3211 (20 716) 20 in (508 mm) 3596 (22 032) 24 in (610 mm) 4282 (27 626) 28 in (711 mm) 4995 (32 226) TRACK Long Track 18 in (457 mm) closed grousers and CLT 18 in (457 mm) open grousers and CELT 20 in (508 mm) closed grousers and CLT 20 in (508 mm) open grousers and CELT Wide Track 18 in (457 mm) closed grousers and CLT 18 in (457 mm) open grousers and CELT 20 in (508 mm) closed grousers and CLT 20 in (508 mm) open grousers and CELT 24 in (610 mm) closed grousers and CLT 24 in (610 mm) open grousers and CELT LGP 28 in (711 mm) closed grousers and CLT 28 in (711 mm) open grousers and CELT
OPERATOR ENVIRONMENT ROPS canopy Single lever control for speed, steering and direction Forward/reverse speed ratio selector Adjustable armrests Foot rests Retractable seat belt, 2 in (51 mm) Vinyl suspension seat w/back adjustment Rear view mirror Tool storage Headliner Floormat Mirror INSTRUMENTATION Warning lights: Air filter Alternator Diagnostic fault indicator Engine coolant temperature Engine oil pressure Hydraulic filter Low fuel level Park brake engaged Service soon indicator Transmission filter Transmission pressure Transmission temperature Gauges: Battery voltage Fuel level Digital hourmeter/tachometer/diagnostic/ service reminder Transmission oil temperature Transmission speed indicator Water temperature Audible warnings: Engine coolant temperature Engine oil pressure Low fuel level Transmission pressure Temperature/hydraulic temperature BLADE Variable blade pitch Lift speed (per second) Cutting edge Width Thickness RIPPER Max. penetration Width Cut width Max. ground clearance Points 52 forward 60 rearward 18 in (457 mm) Reversible and replaceable 8.0 in (203 mm) 0.75 in (19 mm) 14 in (356 mm) 72.4 in (1839 mm) 70.1 in (1780 mm) 17.3 in (439 mm) Replaceable Max. number of shanks 5 Tooth spacing with 5 teeth 17.8 in (452 mm) with 3 teeth 34 in (864 mm) Hydraulic cylinder (double-acting) Diameter 3.25 in (82.6 mm) Stroke 8.4 in (213 mm) Rod 1.75 in (44.5 mm) SERVICE CAPACITIES Fuel tank 50 gal (189.3 L) Engine oil w/filter 13 qt (12.3 L) Engine oil w/o filter 12.2 qt (11.5 L) Engine cooling system 24 qt (22.5 L) Hydraulic reservoir 20 gal (75.7 L) Final drive (per side) 15 qt (14.2 L) Track rollers (ea.) 0.26 qt (0.25 L) Front idlers (ea.) 0.52 qt (0.49 L) Carrier rollers (ea.) 0.25 qt (0.24 L) OPERATING WEIGHTS Unit equipped with ROPS, full fuel tank, 170 lb (77 kg) operator, drawbar, side shield, track guides, backup alarm, horn and lights. Long Track Wide Track LGP Add-on weights Drawbar Ripper (3 shank) Winch Front counterweight Cab ROPS heater CELT chain Center rockguard Sweeps Dual batteries 18,900 lb (8569 kg) 19,700 lb (8955 kg) 20,200 lb (9157 kg) 85 lb (38 kg) 1,400 lb (646 kg) 1,200 lb (545 kg) 880 lb (399 kg) 930 lb (422 kg) 71 lb (32 kg) 115 lb (52 kg) 234 lb (106 kg) 104 lb (47 kg) 64 lb (29 kg) 750L Page 2 of 4
G D E H A C F I B K J DIMENSIONS Long Track (LT) Wide Track (WT) Low Ground Pressure (LGP) BLADES Blade width 104 in (2642 mm) 110 in (2794 mm) 110 in (2794 mm) 120 in (3048 mm) 124 in (3150 mm) SAE blade capacity 2.16 yd 3 (1.65 m 3 ) 2.32 yd 3 (1.77 m 3 ) 2.32 yd 3 (1.77 m 3 ) 2.52 yd 3 (1.93 m 3 ) 2.60 yd 3 (1.99 m 3 ) A. Blade lift above ground 34.4 in (874 mm) 34.4 in (874 mm) 34.4 in (874 mm) 34.4 in (874 mm) 34.4 in (874 mm) B. Blade depth below ground 19 in (483 mm) 19 in (483 mm) 19 in (483 mm) 19 in (483 mm) 19 in (483 mm) Blade angle both directions 25 25 25 25 25 Blade tilt, each end (up to 8.3 ) 15 in (381 mm) 15.9 in (404 mm) 15.9 in (404 mm) 17.3 in (439 mm) 17.9 in (455 mm) C. Blade height 36 in (914 mm) 36 in (914 mm) 36 in (914 mm) 36 in (914 mm) 36 in (914 mm) D. Cast reach 13.7 in (348 mm) 16.4 in (417 mm) 9.4 in (239 mm) 13.9 in (353 mm) 13.8 in (351 mm) E. Cut reach 0.7 in (18 mm) 3.5 in (86 mm) -3.6 in (-91 mm) 0.9 in (23 mm) 0.8 in (20 mm) TRACKS Track gauge 62 in (1.57 m) 62 in (1.57 m) 70 in (1.78 m) 70 in (1.78 m) 70 in (1.78 m) Shoe width 18 in (457 mm) 18 in (457 mm) 24 in (610 mm) 24 in (610 mm) 28 in (711 mm) F. Track on ground 89 in (2.26 m) 89 in (2.26 m) 89 in (2.26 m) 89 in (2.26 m) 89 in (2.26 m) Area of track on ground 3211 in 2 (2.07 m 2 ) 3211 in 2 (2.07 m 2 ) 4282 in 2 (2.76 m 2 ) 4282 in 2 (2.76 m 2 ) 4995 in 2 (3.22 m 2 ) Ground pressure 5.3 psi (40.1 kpa) 5.3 psi (40.1 kpa) 4.5 psi (31.3 kpa) 4.5 psi (31.3 kpa) 4.0 psi (27.6 kpa) DIMENSIONS G. Height to top of ROPS 109.2 in (2773 mm) 109.2 in (2773 mm) 109.2 in (2773 mm) 109.2 in (2773 mm) 109.2 in (2773 mm) Height to top of cab 109.2 in (2773 mm) 109.2 in (2773 mm) 109.2 in (2773 mm) 109.2 in (2773 mm) 109.2 in (2773 mm) with air conditioning 109.8 in (2788 mm) 109.8 in (2788 mm) 109.8 in (2788 mm) 109.8 in (2788 mm) 109.8 in (2788 mm) H. Ground clearance w/drawbar 14.9 in (379 mm) 14.9 in (379 mm) 14.9 in (379 mm) 14.9 in (379 mm) 14.9 in (379 mm) I. Length Blade straight with drawbar 170 in (4322 mm) 170 in (4322 mm) 170 in (4322 mm) 170 in (4322 mm) 170 in (4322 mm) Blade straight with ripper 203 in (5147 mm) 203 in (5147 mm) 203 in (5147 mm) 203 in (5147 mm) 203 in (5147 mm) J. Width Blade straight 104 in (2642 mm) 110 in (2794 mm) 110 in (2794 mm) 120 in (3048 mm) 124 in (3150 mm) Blade angled 96 in (2446 mm) 102 in (2585 mm) 102 in (2585 mm) 111 in (2815 mm) 114 in (2907 mm) K. Over track 80 in (2032 mm) 80 in (2032 mm) 94 in (2388 mm) 94 in (2388 mm) 98 in (2489 mm) 750L Page 3 of 4
STANDARD EQUIPMENT OPERATOR S COMPARTMENT Isolation mounted ROPS/FOPS canopy with headliner and floormat Vinyl suspension seat w/back adjustment & adjustable armrests Retractable seat belt, 2 in (51 mm) Foot rests ENGINE Case 445TA/E66 Automatic fan belt tensioner Integral engine oil cooling Fuel filter Dual element air cleaner 90 amp alternator 700 CCA 12-volt battery Anti-sandblast radiator Engine side panels Anti-freeze to -34 F Pusher fan POWERTRAIN Dual path infinitely variable, single-lever controlled hydrostatic drive with electronic straight tracking, power turns & counter-rotation, 4-position forward/reverse ratio control Final drive Triple reduction helical gear/planetary. decelerator with hydrostatic drive retardation Automatic spring applied hydraulic release parking brake BLADE 52-60 variable pitch with integral adjustment tool Single lever control for blade lift, angle and tilt UNDERCARRIAGE Easy clean track covers Hydraulic track adjusters Case Lubricated Track Chain Permanently lubricated track and carrier rollers Track adjuster guard Track guides (front and rear) Shock resistance idler mounting OTHER Backup alarm Horn Anti-vandalism package Mirror Pre-cleaner Operator s manual enclosure Master disconnect switch Front pull hook Hand throttle Decelerator Final drive seal guard O-ring face seal hydraulic fittings Vertical spin-on hydraulic & fuel filters Hinged grill with tether Tool storage area OPTIONAL EQUIPMENT OPERATOR S COMPARTMENT Cab (w/heater, 25,598 BTU (7.5 kw)/hr air conditioner, defroster, front windshield washer and 2F-1R lights) 3 in (76 mm) seat belt Deluxe air suspension seat HYDRAULICS 4 spool hydraulic valve for field-installed ripper REAR MOUNTED EQUIPMENT Ripper, parallelogram 5 slot with 3 shanks BLADES 104 in (2.6 m) or 110 in (2.6 m) LT w/18 in (457 mm) shoes 110 in (2.6 m) or 120 in (3.0 m) WT w/20 in (508 m) shoes 120 in (3.0 m) WT w/24 in (610 mm) shoes 124 in (3.15 m) LGP w/28 in (711 mm) shoes 130 in (3.3 m) LGP w/28 in (711 mm) shoes GUARDS Sweeps Center rockguard SCREENS Rear ROPS and cab Side ROPS Radiator brush OTHER Lights halogen, 4 front, 2 rear for cab or ROPS Counterweight, front Retrieval hitch Drawbar Special paint Case Extended Life Track Cold start aid with dual batteries Turbo precleaner Winch drive NOTE: All specifications are stated in accordance with SAE Standards or Recommended Practices, where applicable. NOTE: All engines meet current EPA emissions requirements. IMPORTANT: Case Construction Inc. reserves the right to change these specifications without notice and without incurring any obligation relating to such change. Case Construction Inc. does not warrant the safety or reliability of attachments from other manufacturers. Case is a registered trademark of CNH America LLC. Any trademarks referred to herein, in association with goods and/or services of companies other than CNH America LLC, are the property of those respective companies. www.casece.com Form No. CCE10250702 Printed in U.S.A. 2008 CNH America LLC Replaces form no. None All Rights Reserved
L SERIES CRAWLER DOZERS 750L I 850L
L SERIES CRAWLER DOZERS 750L I 850L Climb in and feel the power. For site prep or fi nish grading, road-and-bridge, residential or commercial work, Case 750L and 850L crawler dozers have the power to get the job done. Whether you need stability to work on steep slopes or extra power to carry your load through a turn, Case dozers deliver. And they do it with exceptional control and maneuverability. Like all Case equipment, these dozers are industry leaders when it comes to serviceability. They re also top of the line in terms of operator comfort. What that means for your business is more time productive time running the machine and less time maintaining it. And that delivers more money to the bottom line. More power Tier 3-certifi ed engines on the 750L and 850L produce 84 and 96 net horsepower, respectively. That s enough muscle to move any material around the job site. The Case PowerStat hydrostatic drivetrain delivers greater drawbar pull at all travel speeds for more push power and productivity. The combination of 10 speed settings with infi nitely variable steering provides maximum maneuverability with counter rotation. A variable-displacement dual-path hydrostatic drive delivers plenty of pulling power. Easy operation Single-lever speed control provides adjustable steering for easy, precise operation. By tilting the control right or left, operators can slow the track on either side to turn the machine. This maintains power to both tracks, letting you push a full load through a turn without braking or raising the blade. Operators can also adjust the sensitivity of the steering and the forward/reverse modulation to suit personal preference or conditions. These easy-to-operate controls boost productivity in any application, making the 750L and 850L ideal for residential, commercial or road-and-bridge work. 750L LT 750L WT 750L LGP
850L XLT 850L WT 850L LGP 3
L SERIES CRAWLER DOZERS 750L I 850L Tier 3-certified engine The Case 750L and 850L crawler dozers are powered by turbocharged Tier 3-certifi ed, fueleffi cient Case Family IV engines. The 4.5-liter and 6.7-liter engines deliver 84 and 96 net horsepower respectively and provide cleanburning power and plenty of torque to move more material per hour. Adjustable blade pitch The built-in pitch-adjustment tool makes it easy to set the blade pitch to match soil conditions, with a range from 52 degrees forward to 60 degrees rearward. Exclusive hydrostatic drive Operation is easy with single-lever control of speed and direction. Combine that with the Caseexclusive PowerStat hydrostatic drive, and you have the power and control you need to push the fullest blades of material, even through curves and turns. Undercarriage durability Based on the conditions you re most likely to encounter, you can choose from Case Lubricated Track (CLT) or Case Extended Life Track (CELT) for optimum undercarriage performance. Regardless of which you select, you ll fi nd that the triplereduction, high-capacity fi nal drive with helical-cut gears makes the 750L and 850L among the quietest dozers in their size class. Track options The 750L and 850L are available in long track (LT), wide track (WT) and low ground pressure (LGP) versions to match operating conditions. The 850L also comes in extra long track (XLT). Both dozers feature a 49-degree sloping track frame cover and ample space between track and machine to keep the undercarriage free of dirt and debris. 4
Quieter, comfortable cab Case dozers feature one of the quietest cabs in the industry. Conveniently placed, easy-tooperate controls and an optional air-ride seat help keep the operator comfortable throughout the day. Heat and air conditioning are standard cab features. Low operating height The height of the ROPS is only 109 inches on both the 750L and 850L, making these machines ideal for residential construction projects. The low overall operating height also makes them easier to transport More uptime Easy maintenance keeps your machine in top shape. Quickaccess diagnostic test ports are standard on these crawler dozers. Swing-out service panels and spin-on fi lters reduce maintenance time, too. Easy-access tilt cab The hydraulic, easy-tilt operator platform gives you access to the drivetrain in less than 10 minutes. Attachment options Several attachment options are available, including specialty blades, rippers, drawbars, winches and more. 5
L SERIES CRAWLER DOZERS 750L I 850L Wide-open visibility and unbeatable comfort The fi rst thing you ll notice on the Case 750L and 850L is how easy it is to get into the cab with the wide doors. Once you re sitting in the optional air suspension seat, you can adjust the seat and controls to your liking. Your visibility is clear to the blade and the entire job site. The high-capacity heater and air-conditioning will handle the toughest temperatures. This environment helps operators be more productive. Easy maintenance means more uptime Case designed these crawler dozers, like all Case machines, to be easy to maintain. We know that the easier it is to service and maintain equipment, the more likely it gets done. And that translates into uptime. Ease of maintenance starts with eye-level fl uid sight gauges and ground-line access to key service checkpoints. These include coolant and hydraulic system gauges and quick-access diagnostic ports. An auto belt tensioner, swing-out service panels and spin-on fi lters also speed up routine maintenance. Service access on Case dozers is second to none. With the hydraulic, easy-tilt operator platform, access to the drivetrain takes less than 10 minutes. The bottom line is that these machines are engineered for easy daily maintenance and routine service. That increases uptime and lowers ownership costs.
You can count on Case You can count on Case and your Case dealer for full-service solutions productive equipment, expert advice, fl exible fi nancing, genuine Case parts and fast service. We re here to provide you with the ultimate ownership experience. Case pride You can take pride in the Case name on your machine. It s backed by more than a century of productivity and performance. Case and your Case dealer are here for you, not only when you buy the machine, but also after you put 1,000 or 10,000 hours on it. A rich, proud history Case Construction Equipment s heritage spans more than 165 years. Growing from J.I. Case s innovations with steam-powered machinery in the late 1800s, Case developed road-building equipment that helped create early 20th century streets and highways across the world. By 1912, Case was well on its way to establishing itself as a full-line equipment manufacturer. The company continued to expand its construction equipment business over the years. Celebrating a tradition of innovation In 1957, Case produced the world s fi rst integrated loader/backhoe made and warranted by one manufacturer. Over the decades and into the 21st century, Case has continued to develop a long line of industry fi rsts and has taken a leadership role in pioneering new products and solutions. Today, Case produces 15 lines of equipment and more than 90 models to meet your toughest construction challenges. Supported by manufacturing and sales in more than 150 countries, Case serves the needs of our customers worldwide. Coast-to-coast customer support In North America, Case equipment is sold and serviced by more than 375 dealer locations. No matter where you work, we re here to support and protect your investment and exceed your expectations. To locate a Case dealer or learn more about Case equipment or customer service, go to www.casece.com or call 1-866-54CASE6. It all adds up. You can count on Case. X 7
L SERIES CRAWLER DOZERS 750L LT WT LGP Engine 84 net hp (63 kw) 84 net hp (63 kw) 84 net hp (63 kw) Operating weight 18,900 lb (8569 kg) 19,700 lb (8955 kg) 20,200 lb (9163 kg) Blade capacity 104 in (2.6 m) blade 2.2 cu yd (1.7 cu m) 110 in (2.8 m) blade 2.3 cu yd (1.8 cu m) 124 in (3.1 m) blade 2.6 cu yd (2.0 cu m) Track on ground 89 in (2.3 m) 89 in (2.3 m) 89 in (2.3 m) Biodiesel B5 or B20* B5 or B20* B5 or B20* 850L XLT WT LGP Engine 96 net hp (72 kw) 96 net hp (72 kw) 96 net hp (72 kw) Operating weight 19,600 lb (8900 kg) 20,200 lb (9181 kg) 20,700 lb (9402 kg) Blade capacity 104 in (2.6 m) blade 2.2 cu yd (1.7 cu m) 110 in (2.8 m) blade 2.3 cu yd (1.8 cu m) 124 in (3.1 m) blade 2.6 cu yd (2.0 cu m) Track on ground 93 in (2.4 m) 93 in (2.4 m) 93 in (2.4 m) Biodiesel B5 or B20* B5 or B20* B5 or B20* * B20 approved following Case guidelines for biodiesel blends above fi ve percent. See your Case dealer for details. 750L 850L NOTE: All engines meet current EPA emission regulations. NOTE: All specifi cations are stated in accordance with SAE standards or recommended practices, where applicable. IMPORTANT: Case Construction Equipment Inc. reserves the right to change these specifi cations without notice and without incurring any obligation relating to such change. Availability of some models and equipment builds vary according to the country in which the equipment is used. The illustrations and text may include optional equipment and accessories and may not include all standard equipment. Your Case dealer/distributor will be able to give you details of the products and their specifi cations available in your area. Always read the operator s manual before operating any equipment. Inspect equipment before using it, and be sure it is operating properly. Follow the product safety signs and use any safety features provided. 2009 CNH America LLC. All rights reserved. Case is a registered trademark of CNH America LLC. Any trademarks referred to herein, in association with goods and/or services of companies other than CNH America LLC, are the property of those respective companies. Printed in U.S.A. Form No. CCE200911750L Replaces: CCE12030701 Contains 10% post-consumer fiber Case construction equipment is biodiesel friendly. Looking for product specs, customer testimonials, competitive comparisons, fi nance offers and more? Visit us at www.casece.com or call 866-54CASE6