Marathon Series Corrosion Resistant Mounted Products and Bearing Units

MRC Bearing Services Marathon Series Corrosion Resistant Mounted Products and Bearing Units Composite Series Standard Duty HD i Series Heavy Duty Cast Iron XD s Series Extreme Duty Cast Stainless

Contents Introduction.................................. Composite Units..............................6 Stainless Steel Take-Up Frames.................20 ZMaRC -Coated Cast Iron Units................22 Cast Stainless Steel Units......................26 ZMaRC-Coated Insert Bearings.................0 Stainless Steel Insert Bearings.................. High Temp and Submersible Units...............2 Made-To-Order Products......................5 Nomenclature...............................6 Picker Hub Applications....................... Stainless Steel Ball Bearings...................8 Tolerances and Dimensional Data............................9 Assembly Instructions.........................40 Comparison Charts...........................42

Marathon Series Corrosion-Resistant Mounted Products and Bearing Units Few industries challenge bearings with a harsher operating environment than the food and beverage industries. Perhaps no industry works as hard to meet regulations governing contamination. When MRC introduced the Marathon Series Composite Mounted Bearing Units, it was possibly the best solution to the problems associated with bearing failures. Now the composite units are joined by our HD i heavy-duty cast iron and XD s extreme-duty cast stainless steel to more thoroughly meet the needs of the industry. The HD i Series was developed to provide corrosion resistance together with the strength of cast iron but eliminate the problem of flaking nickel plating. These units consist of a ZMaRC coated cast iron housing in combination with a ZMaRC coated insert bearing and are priced competitively with other nickel-plated versions. (See page for more details.) For extremely challenging applications, MRC offers the XD s Series, with top-of-the-line corrosion resistance and the greatest housing strength available within the Marathon line. These housings utilize an AISI 00 series cast stainless steel housing together with MRC s proven stainless steel insert bearing. (See page 4 for more details.) The entire maintenance-free Marathon Series is built to resist corrosion and is designed for extended service life. At the heart of the units are high-quality, corrosionresistant insert bearings, available with MRC s ZMaRC coating or with stainless steel construction. The units multifunction low-friction, rubber seals are bonded to AISI 04 stainless steel for superior corrosion resistance, and sealed-for-life lubricants are USDA approved.

A Composite Housing with Integrated Performance Features The Marathon Series composite housing resists citric acids, cooking fats and most chemicals used in food and beverage processing. It is constructed of a thermoplastic composite material that can be up to 6% lighter than cast iron housings. Its spherical bore accommodates the insert bearing s spherical outer surface, enabling the unit to fully compensate for initial bearing seating misalignment. Plus, the housing is loaded with design and performance advantages: Steel coils embedded in the housing contribute to the housing s fracture strength. Radial breaking load is far greater than the static load rating of the bearing. Marathon Series housings have possibly the highest fracture strength of any composite unit available. Apolyurethane-filled housing base enables the unit to meet flush with its mounting surface. Flush surface-tosurface mounting eliminates gaps potential areas for contaminants to collect. 00 Series stainless steel bolt hole inserts provide added strength to each housing foot and prevent corrosion. Marathon Series units are available in the following housing designs to meet the needs of most food and beverage processing applications: pillow blocks two- or four-bolt flange tapped base three-bolt bracket flange narrow and wide slot take-up low backing height pillow block low profile two- and three-bolt flange four-bolt piloted flange hanger 04 stainless steel set screws 20 degrees apart. Choice of ZMaRCcoated or stainless steel insert bearing. Polyurethane-filled base. No gaps where contaminants can collect. 04 stainless steel double contact seal and flinger. Insert bearing is prelubricated with USDA approved grease. Light gray polyamide composite housing resists corrosion. Polyamide Cage. Stainless steel bolt hole inserts. 2

NEW! ZMaRC Coated Cast Iron Units with ZMaRC coated Insert Bearings MRC s newest solution to the unique needs of the food processing industry is Marathon HD i a new corrosionresistant, heavy-duty cast iron series of bearing units. The cast iron housings, protected with MRC s proven ZMaRC coating, eliminate the flaking problems associated with nickel-plated products. The housings are matched with our ZMaRC-plated, lubed-for-life, quality insert bearings. The HD i series provides a number of cost-saving and performance benefits. As with all Marathon products, MRC s patented two-part stainless steel seals allow the units to operate in heavy washdown environments without regreasing. And since there is no need for relubrication, continuous grease purge is never a problem. Advantages of the HD i Series: Complete ZMaRC coating on all housing surfaces for long-term corrosion resistance. ZMaRC coating will not flake off. Housings and bearings are resistant to the majority of common washdown solutions. HD i units require no relubrication, even in a washdown environment saving time and money while providing a cleaner-running unit. Open spaces on bases and backs of ZMaRC-coated housings are filled with polyurethane, eliminating areas where moisture and product can collect, resulting in a more sanitary housing design. All HD i units are factory lubed-for-life with USDA approved H grease. Two-part sealing for maximum protection Like all Marathon bearing units, Marathon HD i units contain an AISI 04 stainless steel inner seal and outer seal. These components work in tandem to form an extremely effective sealing system. (See page 5 for more details.) The added strength and durability of the Marathon HD i housings make them particularly well suited for applications in red meat, pork and poultry processing facilities where both housing strength and corrosion resistance are a concern. The HD i Series is available in the following housing designs: pillow blocks two- or four-bolt flange tapped base

Extreme Duty Cast Stainless Steel Mounted Units Composite housing units are suitable for many food and beverage industry applications. However, there are extremely challenging applications that require a even more durable unit the XD s line of Marathon units. These housings are AISI 00 series cast stainless steel with MRC s proven stainless steel insert bearings. The cast stainless housings are the strongest housings offered in the Marathon family. For any application where loads are very heavy or where shock loads are possible, the extra strength and toughness of the stainless steel housings are a benefit. Also, in applications where failure of the housing could result in injury, such as in cases where workers pass below a portion of a machine, the safety factor inherent in the cast steel housing is desirable. Exposure to extremely aggressive washdown chemicals is another reason to choose these stainless units. While composite and plated housings are resistant to most of the chemicals in use today, they can be susceptible to some strong concentrations of chlorine, hydrogen peroxide and other chemicals. The cast stainless housings, made of an AISI 00 series stainless material, are not affected by those same chemicals. The XD s cast stainless housings were designed from the ground up for use in food and beverage applications. The bases are cast flat with no recesses to trap debris and bacteria, and the exposed surfaces of the housings have no unnecessary crevices or pockets. Consideration was given to surface roughness as well. The XD s units smooth cast surfaces minimize the material trapped on the surface allowing a more thorough cleaning. the application involves heavy loads, aggressive chemicals or intolerance to bacteria buildup, the XD s units are up to the challenge. Housing styles available include: pillow block two- and four-bolt flange tapped base MRC XDs Extreme Duty Machined Stainless Steel Mounted Units MRC can also offer additional housing styles in machined stainless steel. These units also utilize AISI 00 series stainless steel but, rather than using a cast housing, these units are machined from solid stainless plate. Due to this manufacturing difference, these housings offer even better surface roughness since all surfaces are machined. These are especially suited for applications where surface roughness is critical, such as instances where chronic bacterial problems have existed. As with the cast housings, there are no unnecessary recesses or cavities to trap debris. Just like the cast stainless units, MRC s excellent stainless steel insert bearings are used. In addition to the styles listed above, are available in housing styles: three-bolt bracket flange wide and narrow slot take-up units compact two- and three-bolt flange piloted flange units All machined housings are available through the MRC MTO (Made To Order) program. Like the other members of the Marathon family, the XD s series incorporates the proven insert bearing design and patented sealing arrangement (see page 5), and are also greased for life and maintenance free. Marathon XD s is MRC s top of the line unit. Whether 4

Choose from ZMaRC-coated The Marathon Series is designed to withstand food processing environments. The unit s high quality insert bearing is available with MRC s proprietary ZMaRC coating on the inner and outer rings. ZMaRC resists frequent wash downs with water and with acidic and caustic solutions far better than conventional insert bearings and conventional coatings, such as black oxide. In food and beverage applications, that means greater protection against rust, greater protection against contaminant-related bearing failure and greater assurance that your equipment will pass USDA inspections....or Stainless Steel Insert Bearings If you prefer stainless steel, MRC will supply the Marathon Series with AISI 420 C stainless inner and outer rings and balls. Both ZMaRC-coated and stainless steel insert bearings come in bore sizes ranging from /4" to /2", and 20 mm to 40 mm. ZMaRC is also available in 5 /6". The insert bearing s stainless steel set screws, positioned 20 degrees apart, minimize inner ring distortion while maintaining good gripping strength. A Stainless Steel Sealing Arrangement Double-guards Against Contaminants A double-protection seal keeps Marathon Series Mounted Bearing Units running contaminant free. The sealing arrangement consists of a double-lip, AISI 04 stainless steel insert seal, an AISI 04 stainless steel flinger and a rubber-backed seal gasket. The flinger and seal s lowfriction rubber lips, with optimized axial contact, form a double barrier against pollutants and wash downs. The seal gasket prevents contaminants from migrating around the seal insert s O.D. The flinger adds mechanical and centrifugal protection against contaminant entry. The space between the insert seal and flinger is filled with USDA Food Grade grease for even greater sealing efficiency. USDA-approved Grease Marathon Series Composite Mounted Bearing Units are prelubricated-for-life with USDA H-approved grease. The high quality synthetic grease is odorless and tasteless, leaving foodstuffs unaffected by lubricant contact. It is approved for use in all food processing industries, including meat, fish, poultry and fruit processing equipment. And it resists washout, even during frequent washdowns with hot and cold water, and with disinfectant solutions. Other Marathon Mounted Bearing Unit grease benefits: Excellent internal and external bearing corrosion protection. High aging resistance for extended lubricant life. High load carrying capacity, which helps prevent premature bearing wear. 5

CPB Composite Pillow Block Units ZMaRC-Coated Insert Bearing ;A d S H H A For Inch Shafts 4 5 6 Shaft Pillow Block J J Speed d Designation A A H H H 2 Min Max L N N G S Weight Dynamic C Static C 0 Rating in in in in in in in in in in in in in lb lbf lbf RPM mm mm mm mm mm mm mm mm mm mm mm mm kg N N 4 CPBO2ZM 5 4 2 5 5 6 8 9 4 4 2 2 8 0.5 2 860 40 2 2 64. 6 9.5 0.5 26.5 0 8. 0.24 2 00 6 550 5 00 5 6 CPB05ZM 4 8 2 25 5 6 8 4 5 9 2 25 8 0.65 50 50 2 22 0.5 6.5 6 99.5 0.5 4.5 0 9.8 0. 4 000 800 CPB00ZM 4 8 2 25 5 6 8 4 5 9 2 25 8 0.62 50 50 2 22 0.5 6.5 6 99.5 0.5 4.5 0 9.8 0.28 4 000 800 8 CPB02ZM 6 5 6 4 4 4 5 6 5 5 4 8.0 4 80 2 520 40 25 82 42.9 9 08 28 59 2 4 2 22.2 0.50 9 500 200 6 CPB0ZM 6 5 6 4 4 4 5 6 5 5 4 8.04 4 80 2 520 40 25 82 42.9 9 08 28 59 2 4 2 22.2 0.4 9 500 200 4 CPB04ZMR 6 5 6 4 4 4 5 6 5 5 4 8.0 4 80 2 520 40 25 82 42.9 9 08 28 59 2 4 2 22.2 0.46 9 500 200 4 CPB04ZM 49 6 2 8 4 4 6 5 4 6 5 5 5.5 5 0 440 45 2 9 4.6 9 9 64 2 4 2 25.4 0. 25 500 5 00 6 CPB0ZM 49 6 2 8 4 4 6 5 4 6 5 5 5. 5 0 440 45 2 9 4.6 9 9 64 2 4 2 25.4 0.62 25 500 5 00 CPB08ZM 5 6 5 25 6 5 5 5 5 8 6 5 5 5 6.98 6 900 4 20 48 0 99 49.2 20 4 5 2 4 2 0 0.90 0 00 9 000 5 2 6 CPB5ZM 2 4 2 4 4 5 8 2 4 4 5 8 6 4 8 8 2 5 6 8 9 2.95 890 5 220 5.2 5.2.5 5.2 9. 49.2.5 206.4 2 6. 6 2.6.4 5 00 2 200 For Metric Shafts 20mm 40mm Shaft Pillow Block J J Speed d Designation A A H H H 2 Min Max L N N G S Weight Dynamic C Static C 0 Rating mm in in in in in in in in in in in in lb lbf lbf RPM mm mm mm mm mm mm mm mm mm mm mm mm kg N N 20 CPB20ZM 5 4 2 5 5 6 8 9 4 4 2 2 8 0.5 2 860 40 2 2 64. 6 9.5 0.5 26.5 0 8. 0.24 2 00 6 550 5 00 25 CPB25ZM 4 8 2 25 5 6 8 4 5 9 2 25 8 0.64 50 50 2 22 0.5 6.5 6 99.5 0.5 4.5 0 9.8 0. 4 000 800 0 CPB0ZM 6 5 6 4 4 4 5 6 5 5 4 8.08 4 80 2 520 40 25 82 42.9 9 08 28 59 2 4 2 22.2 0.49 9 500 200 5 CPB5ZM 49 6 8 4 4 6 5 4 6 5 5 5.46 5 0 440 45 2 9 4.6 9 9 64 2 4 2 25.4 0.66 25 500 5 00 40 CPB40ZM 5 6 5 25 6 5 5 5 5 8 6 5 5 5 6.90 6 900 4 20 48 0 99 49.2 20 4 5 2 4 2 0 0.86 0 00 9 000 4 200 800 800 200 200 2 900 4 200 800 200 2 900 MRC Marathon Series Composite Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. Cast polymer housing. No steel coils. 6 2 Check with MRC for availability

CPB Composite Pillow Block Units Stainless Steel Insert Bearing ;A d S H H A For Inch Shafts 4 Shaft Pillow Block J J Speed d Designation A A H H H 2 Min Max L N N G S Weight Dynamic C Static C 0 Rating in in in in in in in in in in in in in lb lbf lbf RPM mm mm mm mm mm mm mm mm mm mm mm mm kg N N 4 CPBO2SS CPB00SS 6 CPB0SS 4 5 2 5 6 5 8 9 4 4 2 8 2 0.5 2 80 40 2 2 64. 6 9.5 0.5 26.5 0 8. 0.24 0 600 6 550 4 8 2 25 6 5 8 4 5 9 2 8 25 0.62 2 520 50 2 22 0.5 6.5 6 99.5 0.5 4.5 0 9.8 0.28 200 800 6 5 6 4 4 4 5 6 4 5 5 8.04 50 2 520 40 25 82 42.9 9 08 28 59 2 4 2 22.2 0.4 5 600 200 4 CPB04SSR 6 5 6 4 4 4 5 6 5 5 4 8.04 50 2 520 40 25 82 42.9 9 08 28 59 2 4 2 22.2 0.4 5 600 200 4 CPB04SS 8 CPB06SS 6 CPB0SS CPB08SS 49 6 2 8 4 4 6 5 4 6 5 5 5.5 4 560 440 45 2 9 4.6 9 9 64 2 4 2 25.4 0. 20 00 5 00 49 6 2 8 4 4 6 5 4 6 5 5 5.44 4 560 440 45 2 9 4.6 9 9 64 2 4 2 25.4 0.65 20 00 5 00 49 6 2 8 4 4 6 5 4 6 5 5 5. 4 560 440 45 2 9 4.6 9 9 64 2 4 2 25.4 0.62 20 00 5 00 5 6 5 6 25 5 5 5 5 8 6 5 5 5 6.98 5 550 4 20 48 0 99 49.2 20 4 5 2 4 2 0 0.90 24 00 9 000 5 00 4 200 200 200 200 200 200 2 900 For Metric Shafts 20mm 40mm Shaft Pillow Block J J Speed d Designation A A H H H 2 Min Max L N N G S Weight Dynamic C Static C 0 Rating mm in in in in in in in in in in in in lb lbf lbf RPM mm mm mm mm mm mm mm mm mm mm mm mm kg N N 20 CPB20SS 25 CPB25SS 0 CPB0SS 5 CPB5SS 40 CPB40SS 4 5 2 5 6 5 8 9 4 4 2 8 2 0.5 2 80 40 2 2 64. 6 9.5 0.5 26.5 0 8. 0.24 0 600 6 550 4 8 2 25 6 5 8 4 5 9 2 8 25 0.64 2 520 50 2 22 0.5 6.5 6 99.5 0.5 4.5 0 9.8 0. 200 800 6 5 6 4 4 4 5 6 4 5 5 8.08 50 2 520 40 25 82 42.9 9 08 28 59 2 4 2 22.2 0.49 5 600 200 49 6 2 8 4 4 6 5 4 6 5 5 5.46 4 560 440 45 2 9 4.6 9 9 64 2 4 2 25.4 0.66 20 00 5 00 5 6 5 6 25 5 5 5 5 8 6 5 5 5 6.90 5 550 4 20 48 0 99 49.2 20 4 5 2 4 2 0 0.86 24 00 9 000 5 00 4 200 800 200 2 900 MRC Marathon Series Composite Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings

C2F Composite Two-Bolt Flange Units ZMaRC-Coated Insert Bearing ; T A d D a G A 2 For Inch Shafts 4 5 6 Shaft Flange Unit Speed d Designation A A 2 Da H J L N G T Weight Dynamic C Static C 0 Rating in in in in in in in in in in lb lbf lbf RPM mm mm mm mm mm mm mm mm mm kg N N 4 C2F02ZM 5 6 C2F05ZM C2F00ZM 8 C2F02ZM 6 C2F0ZM 4 C2F04ZMR 4 C2F04ZM 6 C2F0ZM Shaft Flange Unit Speed d Designation A A 2 Da H J L N G T Weight Dynamic C Static C 0 Rating mm in in in in in in in in in lb lbf lbf RPM mm mm mm mm mm mm mm mm mm kg N N 20 C2F20ZM 25 C2F25ZM 0 C2F0ZM 5 C2F5ZM 5 9 2 4 2 8 8 5 0.5 2 860 40.5 5 50.8 2 90 60.5.5 0. 0.24 2 00 6 550 6 9 2 4 8 2 4 8 0.6 50 50 0 5 6.5 24 99 0.5 0 8.8 0.0 4 000 800 6 9 2 4 8 2 4 8 0.62 50 50 0 5 6.5 24 99 0.5 0 8.8 0.28 4 000 800 9 9 5 9 4 9 8 2 0.99 4 80 2 520 5 6.2 42.5 6.5 8.5 0 42.2 0.45 9 500 200 9 9 5 9 4 9 8 2 0.9 4 80 2 520 5 6.2 42.5 6.5 8.5 0 42.2 0.42 9 500 200 9 9 5 9 4 9 8 2 0.88 4 80 2 520 5 6.2 42.5 6.5 8.5 0 42.2 0.40 9 500 200 8 2 6 8 5 8 25 5 5.46 5 0 440 5 88.9 56 0 96 4 2 46.4 0.66 25 500 5 00 8 2 6 8 5 8 25 5 5.28 5 0 440 5 88.9 56 0 96 4 2 46.4 0.58 25 500 5 00 C2F08ZM 9 4 6 6 25 5 2 4 9 6 2.90 6 900 4 20.8 4. 88.9 2.2 4. 5.9.5 2 5.66 0.86 0 00 9 000 5 6 C2F5ZM 2 5 4 8 4 5 6 6 6 5 6 2 8 2.25 890 5 220.8 5.9 0.6 85. 5.2 28.6.5 2 54.02 5 00 2 200 For Metric Shafts 20mm 40mm 5 9 2 4 2 8 8 5 0.5 2 860 40.5 5 50.8 2 90 60.5.5 0. 0.24 2 00 6 550 6 9 2 4 8 2 4 8 0.64 50 50 0 5 6.5 24 99 0.5 0 8.8 0. 4 000 800 9 9 5 9 4 9 8 2 0.9 4 80 2 520 5 6.2 42.5 6.5 8.5 0 42.2 0.44 9 500 200 8 2 6 8 5 8 25 5 5.5 5 0 440 5 88.9 56 0 96 4 2 46.4 0.6 25 500 5 00 40 C2F40ZM 9 4 6 6 25 5 2 4 9 6 2.90 6 900 4 20.8 4. 88.9 2.2 4. 5.9.5 2 5. 0.86 0 00 9 000 5 00 4 200 800 800 200 200 5 00 4 200 800 200 MRC Marathon Series Composite Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. Cast polymer housing, no steel coils. 8 2 Check with MRC for availability

C2F Composite Two-Bolt Flange Units Stainless Steel Insert Bearing ; T A d D a G A 2 For Inch Shafts 4 Shaft Flange Unit Speed d Designation A A 2 Da H J L N G T Weight Dynamic C Static C 0 Rating in in in in in in in in in in lb lbf lbf RPM mm mm mm mm mm mm mm mm mm kg N N 4 C2F02SS C2F00SS 6 C2F0SS 4 C2F04SSR 4 C2F04SS 8 C2F06SS 6 C2F0SS 5 9 2 4 2 8 8 5 0.5 2 80 40.5 5 50.8 2 90 60.5.5 0. 0.24 0 600 6 550 6 9 2 4 8 2 4 8 0.62 2 520 50 0 5 6.5 24 99 0.5 0 8.8 0.28 200 800 9 9 5 9 4 9 8 2 0.9 50 2 520 5 6.2 42.5 6.5 8.5 0 42.2 0.42 5 600 200 9 9 5 9 4 9 8 2 0.9 50 2 520 5 6.2 42.5 6.5 8.5 0 42.2 0.42 5 600 200 8 2 6 8 5 8 25 5 5.46 4 560 440 5 88.9 56 0 96 4 2 46.4 0.66 20 00 5 00 8 2 6 8 5 8 25 5 5.5 4 560 440 5 88.9 56 0 96 4 2 46.4 0.6 20 00 5 00 8 2 6 8 5 8 25 5 5.28 4 560 440 5 88.9 56 0 96 4 2 46.4 0.58 20 00 5 00 C2F08SS 9 4 6 6 25 5 2 4 9 6 2.90 5 550 4 20.8 4. 88.9 2.2 4. 5.9.5 2 5. 0.86 24 00 9 000 5 00 4 200 200 200 200 200 For Metric Shafts 20mm 40mm Shaft Flange Unit Speed d Designation A A 2 Da H J L N G T Weight Dynamic C Static C 0 Rating mm in in in in in in in in in lb lbf lbf RPM mm mm mm mm mm mm mm mm mm kg N N 20 C2F20SS 25 C2F25SS 0 C2F0SS 5 C2F5SS 5 9 2 4 2 8 8 5 0.5 2 80 40.5 5 50.8 2 90 60.5.5 0. 0.24 0 600 6 550 6 9 2 4 8 2 4 8 0.64 2 520 50 0 5 6.5 24 99 0.5 0 8.8 0. 200 800 9 9 5 9 4 9 8 2 0.9 50 2 520 5 6.2 42.5 6.5 8.5 0 42.2 0.44 5 600 200 8 2 6 8 5 8 25 5 5.5 4 560 440 5 88.9 56 0 96 4 2 46.4 0.6 20 00 5 00 40 C2F40SS 9 4 6 6 25 5 2 4 9 6 2.90 5 550 4 20.8 4. 88.9 2.2 4. 5.9.5 2 5. 0.86 24 00 9 000 MRC Marathon Series Composite Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. Cast polymer housing, no steel coils. 5 00 4 200 800 200 Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings 9

C4F Composite Four-Bolt Flange Units ZMaRC-Coated Insert Bearing T A d D a G A 2 For Inch Shafts 4 5 6 Shaft Flange Unit Speed d Designation A A 2 Da J L N G T Weight Dynamic C Static C 0 Rating in in in in in in in in in lb lbf lbf lbf mm mm mm mm mm mm mm mm kg N N 4 C4F02ZM 9 6 2 6 2 8 8 5 0.5 2 860 40 0 5 68.5 6.5 86.5 0. 0.26 2 00 6 550 5 00 5 6 C4F05ZM C4F00ZM 8 C4F02ZM 6 C4F0ZM 4 C4F04ZMR 4 C4F04ZM 6 C4F0ZM C4F08ZM Shaft Flange Unit Speed d Designation A A 2 Da J L N G T Weight Dynamic C Static C 0 Rating mm in in in in in in in in lb lbf lbf lbf mm mm mm mm mm mm mm mm kg N N 20 C4F20ZM 9 6 2 6 2 8 8 5 0.5 2 860 40 0 5 68.5 6.5 86.5 0. 0.26 2 00 6 550 5 00 25 C4F25ZM 0 C4F0ZM 5 C4F5ZM 40 C4F40ZM 9 2 5 6 2 4 4 8 0.6 50 50 5 4.6 0 95.5 0 8.8 0.4 4 000 800 9 2 5 6 2 4 4 8 0. 50 50 5 4.6 0 95.5 0 8.8 0.2 4 000 800 9 9 6 4 4 4 8 2.0 4 80 2 520 5 9. 82.5 08.5 0 42.2 0.49 9 500 200 9 9 6 4 4 4 8 2.0 4 80 2 520 5 9. 82.5 08.5 0 42.2 0.46 9 500 200 9 9 6 4 4 4 8 2 0.9 4 80 2 520 5 9. 82.5 08.5 0 42.2 0.44 9 500 200 8 2 4 6 5 8 4 5 8 5 5.5 5 0 440 5 06.4 92 8 4 2 46.4 0. 25 500 5 00 8 2 4 6 5 8 4 5 8 5 5. 5 0 440 5 06.4 92 8 4 2 46.4 0.62 25 500 5 00 2 4 9 6 4 5 8 5 2 9.98 6 900 4 20 9 5.9 0.5 0 4 2 54.2 0.90 0 00 9 000 5 6 C4F5ZM 2 5 4 8 4 5 6 4 8 5 5 2 8 2.45 890 5 220.8 5.9 25.4. 9. 4 2 54.0.2 5 00 2 200 For Metric Shafts 20mm 40mm 9 2 5 6 2 4 4 8 0. 50 50 5 4.6 0 95.5 0 8.8 0. 4 000 800 9 9 6 4 4 4 8 2.06 4 80 2 520 5 9. 82.5 08.5 0 42.2 0.48 9 500 200 8 2 4 6 5 8 4 5 8 5 5.46 5 0 440 5 06.4 92 8 4 2 46.4 0.66 25 500 5 00 2 4 9 6 4 5 8 5 2 9.92 6 900 4 20 9 5.9 0.5 0 4 2 54.2 0.8 0 00 9 000 4 200 800 800 200 200 2 900 4 200 800 200 2 900 MRC Marathon Series Composite Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. Cast polymer housing. No steel coil 0 2 Check with MRC for availability

C4F Composite Four-Bolt Flange Units Stainless Steel Insert Bearing T A d D a G A 2 For Inch Shafts 4 Shaft Flange Unit Speed d Designation A A 2 Da J L N G T Weight Dynamic C Static C 0 Rating in in in in in in in in in lb lbf lbf lbf mm mm mm mm mm mm mm mm kg N N 4 C4F02SS 9 6 2 6 2 8 8 5 0.5 2 80 40 0 5 68. 6.5 86.5 0. 0.26 0 600 6 550 5 00 C4F00SS 6 C4F0SS 4 C4F04SSR 4 C4F04SS 8 C4F06SS 6 C4F0SS C4F08SS 9 2 5 6 2 4 4 8 0. 2 520 50 5 4.6 0 95.5 0 8.8 0.2 200 800 9 9 6 4 4 4 8 2.0 50 2 520 5 9. 82.5 08.5 0 42.2 0.46 5 600 200 6 6 4 4 4 5 6 4.40 4 560 440 2 2. 9. 82.5 08.9. 42.5 0.6 20 00 5 00 8 2 4 6 5 8 4 5 8 5 5.5 4 560 440 5 06.4 92 8 4 2 46.4 0. 20 00 5 00 8 2 4 6 5 8 4 5 8 5 5.46 4 560 440 5 06.4 92 8 4 2 46.4 0.66 20 00 5 00 8 2 4 6 5 8 4 5 8 5 5. 4 560 440 5 06.4 92 8 4 2 46.4 0.62 20 00 5 00 2 4 9 6 4 5 8 5 2 9.98 5 550 4 20 9 5.9 0.5 0 4 2 54.2 0.90 24 00 9 000 4 200 4 200 4 200 200 200 200 2 900 For Metric Shafts 20mm 40mm Shaft Flange Unit Speed d Designation A A 2 Da J L N G T Weight Dynamic C Static C 0 Rating mm in in in in in in in in lb lbf lbf lbf mm mm mm mm mm mm mm mm kg N N 20 C4F20SS 9 6 2 6 2 8 8 5 0.5 2 80 40 0 5 68. 6.5 86.5 0. 0.26 0 600 6 550 5 00 25 C4F25SS 0 C4F0SS 5 C4F5SS 40 C4F40SS 9 2 5 6 2 4 4 8 0. 2 520 50 5 4.6 0 95.5 0 8.8 0. 200 800 9 9 6 4 4 4 8 2.06 50 2 520 5 9. 82.5 08.5 0 42.2 0.48 5 600 200 8 2 4 6 5 8 4 5 8 5 5.46 4 560 440 5 06.4 92 8 4 2 46.4 0.66 20 00 5 00 2 4 9 6 4 5 8 5 2 9.92 5 550 4 20 9 5.9 0.5 0 4 2 54.2 0.8 24 00 9 000 4 200 800 200 2 900 MRC Marathon Series Composite Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings

CTB Composite Tapped-Base Units ZMaRC-Coated Insert Bearing d S H A H G J L F For Inch Shafts 4 5 6 Shaft Tapped-Base Unit d Designation A H H J L F G S Weight Dynamic C Static C 0 in in in in in in in UNC in lb lbf lbf mm mm mm mm mm mm threads mm kg N N 4 CTB02ZM 6 2 5 8 5 6 2 2 0.5 2 860 40 8 6.5 66.. 50.8 6.2 2. 6 8. 0.2 2 00 6 550 5 6 CTB05ZM CTB00ZM 8 CTB02ZM 6 CTB0ZM 4 CTB04ZMR 4 CTB04ZM 6 CTB0ZM CTB08ZM 6 2 5 6 6 2 25 4 0.2 50 50 8 6.5 4.6 6.5 50.8 82.5 2. 6 9.8 0.2 4 000 800 6 2 5 6 6 2 25 4 0.6 50 50 8 6.5 4.6 6.5 50.8 82.5 2. 6 9.8 0.0 4 000 800 5 8 8 6 4 5 4 8 8.06 4 80 2 520 6 4. 85. 42.9 6.2 08.0 5.9 4 22.2 0.48 9 500 200 5 8 8 6 4 5 4 8 8.00 4 80 2 520 6 4. 85. 42.9 6.2 08.0 5.9 4 22.2 0.45 9 500 200 5 8 8 6 4 5 4 8 8.00 4 80 2 520 6 4. 85. 42.9 6.2 08.0 5.9 4 22.2 0.45 9 500 200 4 8 8 4 4 4.60 5 0 440 44.5 98.4 4.6 82.6 4. 9. 25.4 0. 25 500 5 00 4 8 8 4 4 4.60 5 0 440 44.5 98.4 4.6 82.6 4. 9. 25.4 0. 25 500 5 00 8 4 8 5 6 4 4 4 6 2.00 6 900 4 20 4.6 04.8 49.2 88.9 20. 9. 0 0.9 0 00 9 000 5 2 6 CTB5ZM 8 4 4 2 4 4 5 4 8 54 20. 5.2 0.6 46. 22.2 5 8 9 2.6 2.65.20 890 5 00 5 220 2 200 For Metric Shafts 20mm 40mm Shaft Tapped-Base Unit d Designation A H H J L F G S Weight Dynamic C Static C 0 mm in in in in in in UNC in lb lbf lbf mm mm mm mm mm mm threads mm kg N N 20 CTB20ZM 6 2 5 8 5 6 2 2 0.5 2 860 40 8 6.5 66.. 50.8 6.2 2. 6 8. 0.2 2 00 6 550 25 CTB25ZM 0 CTB0ZM 5 CTB5ZM 40 CTB40ZM 6 2 5 6 6 2 25 4 0.6 50 50 8 6.5 4.6 6.5 50.8 82.5 2. 6 9.8 0.0 4 000 800 5 8 8 6 4 5 4 8 8.00 4 80 2 520 6 4. 85. 42.9 6.2 08.0 5.9 4 22.2 0.45 9 500 200 4 8 8 4 4 4.60 5 0 440 44.5 98.4 4.6 82.6 4. 9. 25.4 0. 25 500 5 00 8 4 8 5 6 4 4 4 6 2.00 6 900 4 20 4.6 04.8 49.2 88.9 20. 9. 0 0.9 0 00 9 000 MRC Marathon Series Composite Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit Cast polymer housing. No steel coils. 2

CTB Composite Tapped-Base Units Stainless Steel Insert Bearing d S H A H G J L F For Inch Shafts 4 Shaft Tapped-Base Unit d Designation A H H J L F G S Weight Dynamic C Static C 0 in in in in in in in UNC in lb lbf lbf mm mm mm mm mm mm threads mm kg N N 4 CTB02SS 6 2 5 8 5 6 2 2 0.5 2 80 40 8 6.5 66.. 50.8 6.2 2. 6 8. 0.2 0 600 6 550 CTB00SS 6 CTB0SS 4 CTB04SSR 4 CTB04SS 8 CTB06SS 6 CTB0SS CTB08SS 6 2 5 6 6 2 25 4 0.6 2 520 50 8 6.5 4.6 6.5 50.8 82.5 2. 6 9.8 0.0 200 800 5 8 8 6 4 5 4 8 8.00 500 2 520 6 4. 85. 42.9 6.2 08.0 5.9 4 22.2 0.45 5 600 200 5 8 8 6 4 5 4 8.0 4 560 440 6 4. 85. 42.9 6.2 08.0 5.9 4 25.4 0.59 20 00 5 00 4 8 8 4 4 4.60 4 560 440 44.5 98.4 4.6 82.6 4. 9. 25.4 0. 20 00 5 00 4 8 8 4 4 4.60 4 560 440 44.5 98.4 4.6 82.6 4. 9. 25.4 0. 20 00 5 00 4 8 8 4 4 4.60 4 560 440 44.5 98.4 4.6 82.6 4. 9. 25.4 0. 20 00 5 00 8 4 8 5 6 4 4 4 6 2.00 5 550 4 20 4.6 04.8 49.2 88.9 20. 9. 0 0.9 24 00 9 000 For Metric Shafts 20mm 40mm Shaft Tapped-Base Unit d Designation A H H J L F G S Weight Dynamic C Static C 0 mm in in in in in in UNC in lb lbf lbf mm mm mm mm mm mm threads mm kg N N 20 CTB20SS 6 2 5 8 5 6 2 2 0.5 2 80 40 8 6.5 66.. 50.8 6.2 2. 6 8. 0.2 0 600 6 550 25 CTB25SS 0 CTB0SS 5 CTB5SS 40 CTB40SS 6 2 5 6 6 2 25 4 0.6 2 520 50 8 6.5 4.6 6.5 50.8 82.5 2. 6 9.8 0.0 200 800 5 8 8 6 4 5 4 8 8.00 500 2 520 6 4. 85. 42.9 6.2 08.0 5.9 4 22.2 0.45 5 600 200 4 8 8 4 4 4.60 4 560 440 44.5 98.4 4.6 82.6 4. 9. 25.4 0. 20 00 5 00 8 4 8 5 6 4 4 4 6 2.00 5 550 4 20 4.6 04.8 49.2 88.9 20. 9. 0 0.9 24 00 9 000 MRC Marathon Series Composite Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. Cast polymer housing. No steel coils. Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings

CBF Composite Three-Bolt Bracket Flange Units ZMaRC-Coated Insert Bearing A T N L d C B G H F J For Inch Shafts 4 5 6 Shaft Flange Unit Bolt d Designation A F B C L H J N G T Size Weight Dynamic C Static C 0 in in in in in in in in in in in in lb lbf lbf mm mm mm mm mm mm mm mm mm mm kg N N 5 6 6 4 4 CBF02ZM 6 2 9 6 8 5 6 8 0.5 2 860 40 2.8. 0. 42.9 65. 22.2 8. 8. 0.. 0.2 2 00 6 550 5 6 CBF05ZM 2 4 4 6 2 4 8 5 8 6 8 0.5 50 50 25.4 2. 20. 46.0 69.9 28.6 4. 8. 0. 6.5 0.4 4 000 800 CBF00ZM 8 CBF02ZM 6 CBF0ZM 4 4 6 2 4 8 5 8 6 8 0.0 50 50 25.4 2. 20. 46.0 69.9 28.6 4. 8. 0. 6.5 0.2 4 000 800 6 5 6 2 6 4 4 25 8 5 8.0 4 80 2 520 2.0 2. 8. 52.4 82.6.8 4.6 9.9 0. 9. 0.50 9 500 200 6 5 6 2 6 4 4 25 8 5 8.00 4 80 2 520 2.0 2. 8. 52.4 82.6.8 4.6 9.9 0. 9. 0.45 9 500 200 4 CBF04ZMR 6 5 6 2 6 4 4 25 8 5 8.00 4 80 2 520 2.0 2. 8. 52.4 82.6.8 4.6 9.9 0. 9. 0.45 9 500 200 4 CBF04ZM 6 CBF0ZM CBF08ZM 9 6 6 6 2 8 6 4 2 6.50 5 0 440.0 4. 5.2 60. 96.8 8. 50.8 0.4.5 46.0 0.68 25 500 5 00 9 6 6 6 2 8 6 4 2 6.4 5 0 440.0 4. 5.2 60. 96.8.8 50.8 0.4.5 46.0 0.6 25 500 5 00 9 4 6 6 6 2 9 6 4 4 8 2 4 2.90 6 900 4 20.8 4. 69.9 65. 08.0 4.9 5.2 0.4.5 5.4 0.86 0 00 9 000 5 6 CBF5ZM 2 5 4 8 5 8 2 5 6 4 8 5 8 2 4 2 8 2.25 890 5 220.8 5.9 9. 4.6 2.8 5.9 69.9 0.4.5 54.0.02 5 00 2 200 For Metric Shafts 20 mm 40 mm Shaft Flange Unit Bolt d Designation A F B C L H J N G T Size Weight Dynamic C Static C 0 mm in in in in in in in in in in in lb lbf lbf mm mm mm mm mm mm mm mm mm mm kg N N 5 6 6 4 20 CBF20ZM 6 2 9 6 8 5 6 8 0.5 2 860 40 2.8. 0. 42.9 65. 22.2 8. 8. 0.. 0.2 2 00 6 550 25 CBF25ZM 0 CBF0ZM 5 CBF5ZM 40 CBF40ZM 4 4 6 2 4 8 5 8 6 8 0.0 50 50 25.4 2. 20. 46.0 69.9 28.6 4. 8. 0. 6.5 0.2 4 000 800 6 5 6 2 6 4 4 25 8 5 8.00 4 80 2 520 2.0 2. 8. 52.4 82.6.8 4.6 9.9 0. 9. 0.45 9 500 200 9 6 6 6 2 8 6 4 2 6.4 5 0 440.0 4. 5.2 60. 96.8.8 50.8 0.4.5 46.0 0.6 25 500 5 00 9 4 6 6 6 2 9 6 4 4 8 2 4 2.90 6 900 4 20.8 4. 69.9 65. 08.0 4.9 5.2 0.4.5 5.4 0.86 0 00 9 000 4 MRC Marathon Series Composite Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit Cast polymer housing. No steel coils. 2 Check with MRC for availability

CBF Composite Three-Bolt Bracket Flange Units Stainless Steel Insert Bearing A T N L d C B G H F J For Inch Shafts 4 Shaft Flange Unit Bolt d Designation A F B C L H J N G T Size Weight Dynamic C Static C 0 in in in in in in in in in in in in lb lbf lbf mm mm mm mm mm mm mm mm mm mm kg N N 5 6 6 4 4 CBF02SS 6 2 9 6 8 5 6 8 0.5 2 80 40 2.8. 0. 42.9 65. 22.2 8. 8. 0.. 0.2 0 600 6 550 CBF00SS 6 CBF0SS 4 4 6 2 4 8 5 8 6 8 0.0 2 520 50 25.4 2. 20. 46.0 69.9 28.6 4. 8. 0. 6.5 0.2 200 800 6 5 6 2 6 4 4 25 8 5 8.00 50 2 520 2.0 2. 8. 52.4 82.6.8 4.6 9.9 0. 9. 0.45 5 600 200 4 CBF04SSR 6 5 6 2 6 4 4 25 8 4 8.0 4 560 440 2.0 2. 8. 52.4 82.6.8 4.6 9.9 0. 42.5 0.59 20 00 5 00 4 CBF04SS 8 CBF06SS 6 CBF0SS CBF08SS 9 6 6 6 2 8 6 4 2 6.50 4 560 440.0 4. 5.2 60. 96.8.8 50.8 0.4.5 46.0 0.68 20 00 5 00 9 6 6 6 2 8 6 4 2 6.40 4 560 440.0 4. 5.2 60. 96.8.8 50.8 0.4.5 46.0 0.6 20 00 5 00 9 6 6 6 2 8 6 4 2 6.4 4 560 440.0 4. 5.2 60. 96.8.8 50.8 0.4.5 46.0 0.6 20 00 5 00 9 4 6 6 6 2 9 6 4 4 8 2 4 2.90 5 550 4 20.8 4. 69.9 65. 08.0 4.9 5.2 0.4.5 5.4 0.86 24 00 9 000 For Metric Shafts 20 mm 40 mm Shaft Flange Unit Bolt d Designation A F B C L H J N G T Size Weight Dynamic C Static C 0 mm in in in in in in in in in in in lb lbf lbf mm mm mm mm mm mm mm mm mm mm kg N N 5 6 6 4 20 CBF20SS 6 2 9 6 8 5 6 8 0.5 2 80 40 2.8. 0. 42.9 65. 22.2 8. 8. 0.. 0.2 0 600 6 550 25 CBF25SS 0 CBF0SS 5 CBF5SS 40 CBF40SS 4 4 6 2 4 8 5 8 6 8 0.0 2 520 50 25.4 2. 20. 46.0 69.9 28.6 4. 8. 0. 6.5 0.2 200 800 6 5 6 2 6 4 4 25 8 5 8.00 50 2 520 2.0 2. 8. 52.4 82.6.8 4.6 9.9 0. 9. 0.45 5 600 200 9 6 6 6 2 8 6 4 2 6.4 4 560 440.0 4. 5.2 60. 96.8.8 50.8 0.4.5 46.0 0.6 20 00 5 00 9 4 6 6 6 2 9 6 4 4 8 2 4 2.90 5 550 4 20.8 4. 69.9 65. 08.0 4.9 5.2 0.4.5 5.4 0.86 24 00 9 000 MRC Marathon Series Composite Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. Cast polymer housing. No steel coils. Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings 5

CTN Composite Narrow Slot Take-Up Units ZMaRC-Coated Insert Bearing A J S d C B N For Inch Shafts 4 5 6 A L D G H Shaft Take-Up Unit PIN DIA d Designation A B C L D H G A J N S Weight Dynamic C Static C 0 in in in in in in in in in in in in lb lbf lbf mm mm mm mm mm mm mm mm mm mm mm kg N N 4 CTN02ZM 8 8 2 5 8 6 2 5 25 2 6 8 6 4 6 0.0 2 860 40 4.9 9.4 66. 8. 55.5 22.2. 6.4.9 9.8 8. 0.2 2 00 6 550 5 6 CTN05ZM 2 8 8 2 5 8 9 6 2 5 25 25 6 8 6 4 6 0.5 50 50 4.9 9.4 66. 90.5 55.5 22.2. 6.4.9 9.8 9.8 0.4 4 000 800 CTN00ZM 8 8 2 5 8 9 6 2 5 25 25 6 8 6 4 6 0.0 50 50 4.9 9.4 66. 90.5 55.5 22.2. 6.4.9 9.8 9.8 0.2 4 000 800 8 CTN02ZM 8 4 8 4 5 6 2 6 5 25 4 6 8.20 4 80 2 520 4.9 04.8 88.9 09.5 68. 25.4 2. 6.4.9 9.8 22.2 0.54 9 500 200 6 CTN0ZM 8 4 8 4 5 6 2 6 5 25 4 6 8.0 4 80 2 520 4.9 04.8 88.9 09.5 68. 25.4 2. 6.4.9 9.8 22.2 0.50 9 500 200 4 CTN04ZMR 8 4 8 4 5 6 2 6 5 25 4 6 8.0 4 80 2 520 4.9 04.8 88.9 09.5 68. 25.4 2. 6.4.9 9.8 22.2 0.50 9 500 200 4 CTN04ZM 8 4 8 4 2 6 5 25 4 6.60 5 0 440 4.9 04.8 88.9 4. 68. 25.4 2. 6.4.9 9.8 25.4 0. 25 500 5 00 6 CTN0ZM 8 4 8 4 2 6 5 25 4 6.60 5 0 440 4.9 04.8 88.9 4. 68. 25.4 2. 6.4.9 9.8 25.4 0. 25500 5 00 CTN08ZM 5 8 4 4 4 5 8 4 5 2 5 25 6 8 6 2.0 6 900 4 20 4. 20. 0.6 6.5 82.6.4 6..9 9.5 9.8 0.00 0 00 9 000 5 6 CTN5ZM 5 8 4 4 4 5 4 5 2 5 6 8 9 2.55 890 5 220 4. 20. 0.6 9. 82.6.4 6..9 9.5 2.0 2.6.6 5 00 2 200 For Metric Shafts 20 mm 40 mm Shaft Take-Up Unit PIN DIA d Designation A B C L D H G A J N S Weight Dynamic C Static C 0 mm in in in in in in in in in in in lb lbf lbf mm mm mm mm mm mm mm mm mm mm mm kg N N 20 CTN20ZM 8 8 2 5 8 6 2 5 25 2 6 8 6 4 6 0.0 2 860 40 4.9 9.4 66. 8. 55.5 22.2. 6.4.9 9.8 8. 0.2 2 00 6 550 25 CTN25ZM 0 CTN0ZM 5 CTN5ZM 40 CTN40ZM 8 8 2 5 8 9 6 2 6 8 6 4 5 6 25 25 0.0 50 50 4.9 9.4 66. 90.5 55.5 22.2. 6.4.9 9.8 9.8 0.2 4 000 800 8 4 8 4 5 6 2 6 5 25 4 6 8.0 4 80 2 520 4.9 04.8 88.9 09.5 68. 25.4 2. 6.4.9 9.8 22.2 0.50 9 500 200 8 4 8 4 2 6 5 25 4 6.60 5 0 440 4.9 04.8 88.9 4. 68. 25.4 2. 6.4.9 9.8 25.4 0. 25 500 5 00 5 8 4 4 4 5 8 4 5 2 5 25 6 8 6 2.0 6 900 4 20 4. 20. 0.6 6.5 82.6.4 6..9 9.5 9.8 0.0.00 0 00 9 000 6 MRC Marathon Series Composite Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. Cast polymer housing. No steel coils. 2 Check with MRC for availability

CTN Composite Narrow Slot Take-Up Units Stainless Steel Insert Bearing A J S d C B N For Inch Shafts 4 A L D G H Shaft Take-Up Unit PIN DIA d Designation A B C L D H G A J N S Weight Dynamic C Static C 0 in in in in in in in in in in in in lb lbf lbf mm mm mm mm mm mm mm mm mm mm mm kg N N 4 CTN02SS 8 8 2 5 8 6 2 5 25 2 6 8 6 4 6 0.0 2 80 40 4.9 9.4 66. 8. 55.5 22.2. 6.4.9 9.8 8. 0.2 0 600 6 550 CTN00SS 6 CTN0SS 8 8 2 5 8 9 6 2 6 8 6 4 5 6 25 25 0.0 2 520 50 4.9 9.4 66. 90.5 55.5 22.2. 6.4.9 9.8 9.8 0.2 200 800 8 4 8 4 5 6 2 6 5 25 4 6 8.0 50 2 520 4.9 04.8 88.9 09.5 68. 25.4 2. 6.4.9 9.8 22.2 0.50 5 600 200 4 CTN04SSR 8 4 8 4 5 6 2 6 5 25 4 6.40 4 560 440 4.9 04.8 88.9 09.5 68. 25.4 2. 6.4.9 9.8 25.4 0.6 20 00 5 00 4 CTN04SS 8 CTN06SS 6 CTN0SS CTN08SS 8 4 8 4 2 6 5 25 4 6 8.60 4 560 440 4.9 04.8 88.9 4. 68. 25.4 2. 6.4.9 9.8 22.2 0. 20 00 5 00 8 4 8 4 2 6 5 25 4 6.60 4 560 440 4.9 04.8 88.9 4. 68. 25.4 2. 6.4.9 9.8 25.4 0. 20 00 5 00 8 4 8 4 2 6 5 25 4 6.60 4 560 440 4.9 04.8 88.9 4. 68. 25.4 2. 6.4.9 9.8 25.4 0. 20 00 5 00 5 8 4 4 4 5 8 4 5 2 5 25 6 8 6 2.0 5 550 4 20 4. 20. 0.6 6.5 82.6.4 6..9 9.5 9.8 0.0.00 24 00 9 000 For Metric Shafts 20 mm 40 mm Shaft Take-Up Unit PIN DIA d Designation A B C L D H G A J N S Weight Dynamic C Static C 0 mm in in in in in in in in in in in lb lbf lbf mm mm mm mm mm mm mm mm mm mm mm kg N N 20 CTN20SS 8 8 2 5 8 6 2 5 25 2 6 8 6 4 6 0.0 2 80 40 4.9 9.4 66. 8. 55.5 22.2. 6.4.9 9.8 8. 0.2 0 600 6 550 25 CTN25SS 0 CTN0SS 5 CTN5SS 40 CTN40SS 8 8 2 5 8 9 6 2 6 8 6 4 5 6 25 25 0.0 2 520 50 4.9 9.4 66. 90.5 55.5 22.2. 6.4.9 9.8 9.8 0.2 200 800 8 4 8 4 5 6 2 6 5 25 4 6 8.0 50 2 520 4.9 04.8 88.9 09.5 68. 25.4 2. 6.4.9 9.8 22.2 0.50 5 600 200 8 4 8 4 2 6 5 25 4 6.60 4 560 440 4.9 04.8 88.9 4. 68. 25.4 2. 6.4.9 9.8 25.4 0. 20 00 5 00 5 8 4 4 4 5 8 4 5 2 5 25 6 8 6 2.0 5 550 4 20 4. 20. 0.6 6.5 82.6.4 6..9 9.5 9.8 0.0.00 24 00 9 000 MRC Marathon Series Composite Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. Cast polymer housing. No steel coils. Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings

CTW Composite Wide Slot Take-Up Units ZMaRC-Coated Insert Bearing A S d C B N J For Inch Shafts 4 5 6 A L D H G Shaft Take-Up Unit d Designation A B C L D H G A J N S Weight Dynamic C Static C 0 in in in in in in in in in in in in lb lbf lbf mm mm mm mm mm mm mm mm mm mm mm kg N N 4 CTW02ZM 8 5 8 6 2 8 6 6 2 2 6 0.8 2 860 40 4.9 92. 6.2 9. 60. 2.0..5 6.5 6. 8. 0. 2 00 6 500 5 6 CTW05ZM 2 8 5 8 6 2 6 6 6 2 25 6 0.92 50 50 4.9 92. 6.2 96.8 6.9 2.0..5 6.5 6. 9.8 0.4 4 000 800 CTW00ZM 8 5 8 6 2 6 6 6 2 25 6 0.8 50 50 4.9 92. 6.2 96.8 6.9 2.0..5 6.5 6. 9.8 0.9 4 000 800 8 CTW02ZM 5 8 4 8 4 8 2 4 5 8 5 25 8 8.0 4 80 2 520 4. 04.8 88.9. 69.9.4 9.5.5 4. 9.8 22.2 0.50 9 500 200 6 CTW0ZM 5 8 4 8 4 8 2 4 5 8 5 25 8 8.40 4 80 2 520 4. 04.8 88.9. 69.9.4 9.5.5 4. 9.8 22.2 0.64 9 500 200 4 CTW04ZMR 5 8 4 8 4 8 2 4 5 8 5 25 8.40 4 80 2 520 4. 04.8 88.9. 69.9.4 9.5.5 4. 9.8 25.4 0.64 9 500 200 4 CTW04ZM 5 8 4 8 4 6 5 8 5 25 8.0 5 0 440 4. 04.8 88.9 22.2 6.2.4 9.5.5 4. 9.8 25.4 0. 25 500 5 00 6 CTW0ZM 5 8 4 8 4 6 5 8 5 25 8.50 5 0 440 4. 04.8 88.9 22.2 6.2.4 9.5.5 4. 9.8 25.4 0.68 25 500 5 00 CTW08ZM 5 6 4 4 5 6 9 6 6 5 6 6 6 2.40 6 900 4 20 49.2 4. 0.6 9. 8. 8. 4..5 49.2 2.0 0.0.0 0 00 9 000 5 6 CTW5ZM 5 6 4 4 4 5 6 9 6 9 6 6 5 6 6 9 2.65 890 5 220 49.2 20. 0.6 4.6 90.5 8. 4..5 49.2 2.0 2.6 2.2 5 00 2 200 For Metric Shafts 20 mm 40 mm Shaft Take-Up Unit d Designation A B C L D H G A J N S Weight Dynamic C Static C 0 mm in in in in in in in in in in in lb lbf lbf mm mm mm mm mm mm mm mm mm mm mm kg N N 20 CTW20ZM 8 5 8 6 2 8 6 6 2 2 6 0.8 2 860 40 4.9 92. 6.2 9. 60. 2.0..5 6.5 6. 8. 0. 2 00 6 500 25 CTW25ZM 0 CTW0ZM 5 CTW5ZM 40 CTW40ZM 8 5 8 6 2 6 6 6 6 2 25 0.8 50 50 4.9 92. 6.2 96.8 6.9 2.0..5 6.5 6. 9.8 0.9 4 000 800 5 8 4 8 4 8 2 4 5 8 5 25 8 8.40 4 80 2 520 4. 04.8 88.9. 69.9.4 9.5.5 4. 9.8 22.2 0.64 9 500 200 5 8 4 8 4 6 5 8 5 25 8.50 5 0 440 4. 04.8 88.9 22.2 6.2.4 9.5.5 4. 9.8 25.4 0.68 25 500 5 00 5 6 4 4 5 6 9 6 6 5 6 6 6 2.40 6 900 4 20 49.2 4. 0.6 9. 8. 8. 4..5 49.2 2.0 0.0.0 0 00 9 000 8 MRC Marathon Series Composite Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. Cast polymer housing. No steel coils. 2 Check with MRC for availability

CTW Composite Wide Slot Take-Up Units Stainless Steel Insert Bearing A S d C B N J For Inch Shafts 4 A L D H G Shaft Take-Up Unit d Designation A B C L D H G A J N S Weight Dynamic C Static C 0 in in in in in in in in in in in in lb lbf lbf mm mm mm mm mm mm mm mm mm mm mm kg N N 4 CTW02SS 8 5 8 6 2 8 6 6 2 2 6 0.8 2 80 40 4.9 92. 6.2 9. 60. 2.0..5 6.5 6. 8. 0. 0 600 6 500 CTW00SS 6 CTW0SS 8 5 8 6 2 6 6 6 6 2 25 0.8 2 520 50 4.9 92. 6.2 96.8 6.9 2.0..5 6.5 6. 9.8 0.9 200 800 5 8 4 8 4 8 2 4 5 8 5 25 8 8.40 50 2 250 4. 04.8 88.9. 69.9.4 9.5.5 4. 9.8 22.2 0.64 5 600 200 4 CTW04SSR 5 8 4 8 4 8 2 4 5 8 5 25 8.0 4 560 440 4. 04.8 88.9. 69.9.4 9.5.5 4. 9.8 25.4 0. 20 00 5 00 4 CTW04SS 8 CTW06SS 6 CTW0SS CTW08SS 5 8 4 8 4 6 5 8 5 25 8.0 4 560 440 4. 04.8 88.9 22.2 6.2.4 9.5.5 4. 9.8 25.4 0. 20 00 5 00 5 8 4 8 4 6 5 8 5 25 8.60 4 560 440 4. 04.8 88.9 22.2 6.2.4 9.5.5 4. 9.8 25.4 0. 20 00 5 00 5 8 4 8 4 6 5 8 5 25 8.50 4 560 440 4. 04.8 88.9 22.2 6.2.4 9.5.5 4. 9.8 25.4 0.68 20 00 5 00 5 6 4 4 5 6 9 6 6 5 6 6 6 2.40 5 550 4 20 49.2 4. 0.6 9. 8. 8. 4..5 49.2 2.0 0.0.0 24 00 9 000 For Metric Shafts 20 mm 40 mm Shaft Take-Up Unit d Designation A B C L D H G A J N S Weight Dynamic C Static C 0 mm in in in in in in in in in in in lb lbf lbf mm mm mm mm mm mm mm mm mm mm mm kg N N 20 CTW20SS 8 5 8 6 2 8 6 6 2 2 6 0.8 2 80 40 4.9 92. 6.2 9. 60. 2.0..5 6.5 6. 8. 0. 0 600 6 500 25 CTW25SS 0 CTW0SS 5 CTW5SS 40 CTW40SS 8 5 8 6 2 6 6 6 6 2 25 0.8 2 520 50 4.9 92. 6.2 96.8 6.9 2.0..5 6.5 6. 9.8 0.9 200 800 5 8 4 8 4 8 2 4 5 8 5 25 8 8.40 50 2 520 4. 04.8 88.9. 69.9.4 9.5.5 4. 9.8 22.2 0.64 5 600 200 5 8 4 8 4 6 5 8 5 25 8.50 4 560 440 4. 04.8 88.9 22.2 6.2.4 9.5.5 4. 9.8 25.4 0.68 20 00 5 00 5 6 4 4 5 6 9 6 6 5 6 6 6 2.40 5 550 4 20 49.2 4. 0.6 9. 8. 8. 4..5 49.2 2.0 0.0.0 24 00 9 000 MRC Marathon Series Composite Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. Cast polymer housing. No steel coils. Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings 9

Stainless Steel Take-up Frames MRC take-up frames are constructed of 04 stainless steel and can be equipped with Marathon Series Composite Mounted Bearing Units. They are designed for conveyor systems used in meat, poultry, fruit, vegetable, beverage and other food industry operations. Normally employed at the idler end of conveyor systems, take-up frames support conveyor shafts and act to produce the correct conveyor belt tension. Unlike many take-up frames fabricated on site from non-stainless materials, MRC stainless take-up frames feature sturdy single-piece construction and resist corrosion from frequent washdowns and harsh food industry chemicals. MRC take-up frames mount securely to conveyor systems via four mounting bolts. The frames and take-up bearing units may be adapted to fit most existing conveyor configurations. F C A D E B Narrow Slot Take-up Frame Narrow Slot Stainless Steel Take-up Frames (all dimensions are in inches) Part number Frame size Bolt pattern for /8" bolts Shaft C/L distance Frame accepts these shaft sizes: Travel A B C D E F Bearing bore TFN20SS 8 6 TFN20SS 6 6 4.55 4 9 25 4", 20mm, ", 25mm TFN20SS 9 9 5 2 TFN08SS 9 TFN08SS 6 6 4 4 2.55 2 4 0 2 6", 0mm, 4", TFN08SS 9 9 5 2 8", 5mm, 6" TFN08SS 2 2 8 6 TFN400SS 0 8 TFN400SS 6 6 TFN400SS 9 9 5 4 6.55 2 4 4 6 ", 40mm, 5 6" TFN400SS 2 2 9 TFN400SS 8 8 25 2 20

HACCP-Program Compatible MRC stainless take-up frames help support the stringent sanitation requirements of Hazard Analysis Critical Control Point (HACCP) programs. In addition to being corrosionresistant, the frames have no narrow gaps or crevices that can trap food contaminants. Also, openings in the side and bottom of MRC frames facilitate quick draining during washdowns. F C A D E B Marathon Series Bearing Units Marathon Series bearing units are available separately and may be mounted in MRC take-up frames. These units feature a lightweight thermoplastic housing that resists corrosion from water, citric acid, cleaning agents and most other food industry chemicals. The unit s double-protection sealing arrangement, consisting of an AISI 04 stainless steel insert seal and an AISI 04 stainless steel flinger, protects against both wet and dry contaminants. The units are lubricated for life with a USDA food-grade grease. Marathon units are available with either a corrosionresistant ZMaRC- coated insert bearing or a stainless steel bearing. Wide Slot Take-up Frame Wide Slot Stainless Steel Take-up Frames (all dimensions are in inches) Part number Frame size Bolt pattern for /8" bolts Shaft C/L distance Frame accepts these shaft sizes: Travel A B C D E F Bearing bore TFW00SS 8 6 TFW00SS 6 6 4 8.55 2 4 9 25 4", 20mm, ", 25mm TFW00SS 9 9 4 2 TFW00SS 2 2 5 TFW08SS 9 TFW08SS 6 6 2 0 TFW08SS 9 9 4 4 5.55 2 4 2 2 6", 0mm, 4", TFW08SS 2 2 8 6 8", 5mm, 6" TFW08SS 8 8 24 22 TFW400SS 0 8 TFW400SS 6 6 TFW400SS 9 9 5 4 6.55 2 4 4 6 ", 40mm, 5 6" TFW400SS 2 2 9 TFW400SS 8 8 25 2 Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings 2

ZPB ZMaRC Coated Cast Iron Pillow Block Units ZMaRC-Coated Insert Bearing HD i Series For Inch Shafts 4 5 6 Shaft Pillow Block J J d Designation A A H H H 2 Min Max L N N G S Weight Dynamic C Static C 0 in in in in in in in in in in in in in lb lbf lbf mm mm mm mm mm mm mm mm mm mm mm mm kg N N 4 ZPB02ZM 5 4 2 5 5 6 5 4 5 2 6 8.40 2 860 40 2.0 2.0 64.0. 4.0 88.0 06.0 2.0 20.5.5 0.0 8. 0.64 2 00 6 550 5 6 ZPB05ZM 6 8 2 4 5 6 8 45 4 2 5 49 25 8 8.5 50 50 6.0 22.0 0.0 6.5 6.0 94.0 0.0 0.0 9.5.5 0.0 9.8 0.9 4 000 800 ZPB00ZM 6 8 2 4 5 6 8 45 4 2 5 49 25 8 8.0 50 50 6.0 22.0 0.0 6.5 6.0 94.0 0.0 0.0 9.5.5 0.0 9.8 0. 4 000 800 8 ZPB02ZM 5 2 6 4 4 5 5 6 59 5 8 2.85 4 80 2 520 40.0 25.4 82.0 42.9 6.5 08.0 2.0 52.0 2.5 4.0 2. 22.2.0 9 500 200 6 ZPB0ZM 5 2 6 4 4 5 5 6 59 5 8 2.85 4 80 2 520 40.0 25.4 82.0 42.9 6.5 08.0 2.0 52.0 2.5 4.0 2. 22.2.0 9 500 200 4 ZPB04ZMR 5 2 6 4 4 5 5 6 59 5 8 2.5 4 80 2 520 40.0 25.4 82.0 42.9 6.5 08.0 2.0 52.0 2.5 4.0 2. 22.2.25 9 500 200 4 ZPB04ZM 49 8 2 8 4 4 4 5 5 6 9 5 5.65 5 0 440 45.0 28.0 9.0 4.6 9.0 9.0.0 60.0 2.0 4.0 2. 25.4.65 25 500 5 00 6 ZPB0ZM 49 8 2 8 4 4 4 5 5 6 9 5 5.40 5 0 440 45.0 28.0 9.0 4.6 9.0 9.0.0 60.0 2.0 4.0 2. 25.4.55 25 500 5 00 ZPB08ZM 5 5 6 4 4 59 5 4 6 5 5 5 6 6 4.0 6 900 4 20 48.0.0 99.0 49.2 9.0 25.0 46.0 5.0 24.0 4.0 2. 0.0.95 0 00 9 000 5 6 ZPB5ZM 2 8 8 4 2 4 8 5 55 6 8 45 5 6 8 9 6.0 890 5 220 54.0 5.0 4.0 5.2 22.0 49.0 65.0 20.0 2.0 8.0 6.0 2.6 2.85 5 00 2 200 For Metric Shafts 20mm 40mm* Shaft Pillow Block J J d Designation A A H H H 2 Min Max L N N G S Weight Dynamic C Static C 0 mm in in in in in in in in in in in in lb lbf lbf mm mm mm mm mm mm mm mm mm mm mm mm kg N N 20 ZPB20ZM 5 4 2 5 5 6 5 4 5 2 6 8.40 2 860 40 2.0 2.0 64.0. 4.0 88.0 06.0 2.0 20.5.5 0.0 8. 0.64 2 00 6 550 25 ZPB25ZM 6 8 2 4 5 6 8 45 4 2 5 49 25 8 8.0 50 50 6.0 22.0 0.0 6.5 6.0 94.0 0.0 0.0 9.5.5 0.0 9.8 0. 4 000 800 0 ZPB0ZM 5 2 6 4 4 5 5 6 59 5 8 2.85 4 80 2 520 40.0 25.4 82.0 42.9 6.5 08.0 2.0 52.0 2.5 4.0 2. 22.2.0 9 500 200 5 ZPB5ZM 49 8 2 8 4 4 4 5 5 6 9 5 5.65 5 0 440 45.0 28.0 9.0 4.6 9.0 9.0.0 60.0 2.0 4.0 2. 25.4.65 25 500 5 00 40 ZPB40ZM 5 5 6 4 4 59 5 4 6 5 5 5 6 6 4.0 6 900 4 20 48.0.0 99.0 49.2 9.0 25.0 46.0 5.0 24.0 4.0 2. 0.0.95 0 00 9 000 * Metric units are supplied through the Made To Order (MTO) Program MRC Marathon Series Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. 22

Z2F ZMaRC Coated Cast Iron Two-Bolt Flange Units ZMaRC-Coated Insert Bearing HD i Series For Inch Shafts 4 5 6 Shaft Flange Unit d Designation A A 2 H J L N G T Weight Dynamic C Static C 0 in in in in in in in in in lb lbf lbf mm mm mm mm mm mm mm mm kg N N 6 4 4 Z2F02ZM 2 8 6 8 5 0.90 2 860 40 24.6..9 89. 60.. 0.0. 0.4 2 00 6 550 5 6 Z2F05ZM Z2F00ZM 8 Z2F02ZM 6 Z2F0ZM 4 Z2F04ZMR 4 Z2F04ZM 6 Z2F0ZM Z2F08ZM 5 6 Z2F5ZM For Metric Shafts 20mm 40mm* 6 5 8 4 5 5 2 4 6.5 50 50 0.2 5.9 2.8 98.8 69.9 2..0 8.8 0.6 4 000 800 6 5 8 4 5 5 2 4 6.0 50 50 0.2 5.9 2.8 98.8 69.9 2..0 8.8 0.59 4 000 800 9 5 9 6 4 9 8 6 2 2.05 4 80 2 520 2.5.5 4. 6. 9.4 2..0 42.2 0.9 9 500 200 9 5 9 6 4 9 8 6 2 2.00 4 80 2 520 2.5.5 4. 6. 9.4 2..0 42.2 0.9 9 500 200 9 5 9 6 4 9 8 6 2.95 4 80 2 520 2.5.5 4. 6. 9.4 2..0 42.2 0.88 9 500 200 9 6 6 8 5 8 5 8 9 6 2 2.85 5 0 440 4. 4. 55.6 0.2 92. 4. 2. 46.4.0 25 500 5 00 9 6 6 8 5 8 5 8 9 6 2 2.5 5 0 440 4. 4. 55.6 0.2 92. 4. 2. 46.4.25 25 500 5 00 9 6 6 4 5 2 4 9 6 2 8.5 6 900 4 20 8.9 4..5 4. 0.6 4. 2. 54.2.0 0 00 9 000 2 25 6 6 6 4 9 6 5 8 9 6 2 8 5.05 890 5 220 4. 9.8 88.9 5.2 5.9 5.9 4.0 60.6 2.0 5 00 2 200 Shaft Flange Unit d Designation A A 2 H J L N G T Weight Dynamic C Static C 0 mm in in in in in in in in lb lbf lbf mm mm mm mm mm mm mm mm kg N N 6 4 20 Z2F20ZM 2 8 6 8 5 0.90 2 860 40 24.6..9 89. 60.. 0.0. 0.4 2 00 6 550 25 Z2F25ZM 0 Z2F0ZM 5 Z2F5ZM 40 Z2F40ZM 6 5 8 4 5 5 2 4 6.0 50 50 0.2 5.9 2.8 98.8 69.9 2..0 8.8 0.59 4 000 800 9 5 9 6 4 9 8 6 2 2.05 4 80 2 520 2.5.5 4. 6. 9.4 2..0 42.2 0.9 9 500 200 9 6 6 8 5 8 5 8 9 6 2 2.85 5 0 440 4. 4. 55.6 0.2 92. 4. 2. 46.4.0 25 500 5 00 9 6 6 4 5 2 4 9 6 2 8.5 6 900 4 20 8.9 4..5 4. 0.6 4. 2. 54.2.0 0 00 9 000 * Metric units are supplied through the Made To Order (MTO) Program MRC Marathon Series Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings 2

Z4F ZMaRC Coated Cast Iron Four-Bolt Flange Units ZMaRC-Coated Insert Bearing HD i Series For Inch Shafts 4 5 6 Shaft Flange Unit d Designation A A 2 J L N G T Weight Dynamic C Static C 0 in in in in in in in in lb lbf lbf mm mm mm mm mm mm mm kg N N 4 Z4F02ZM 5 8 8 2 8 6 8.5 2 860 40 28.6 5.9 6.5 85.. 0.0 8.8 0.6 2 00 6 550 5 6 Z4F05ZM Z4F00ZM 8 Z4F02ZM 6 Z4F0ZM 4 Z4F04ZMR 4 Z4F04ZM 6 Z4F0ZM Z4F08ZM 5 6 Z4F5ZM For Metric Shafts 20mm 40mm* 6 5 8 2 4 4 6.85 50 50 0.2 5.9 69.9 95. 2..0 8.8 0.84 4 000 800 6 5 8 2 4 4 6.80 50 50 0.2 5.9 69.9 95. 2..0 8.8 0.82 4 000 800 9 9 4 4 4 6 2 2.65 4 80 2 520 2.5 5. 82.6 08.0 2..0 42.2.20 9 500 200 9 9 4 4 4 6 2 2.65 4 80 2 520 2.5 5. 82.6 08.0 2..0 42.2.20 9 500 200 9 9 4 4 4 6 2 2.65 4 80 2 520 2.5 5. 82.6 08.0 2..0 42.2.20 9 500 200 8 5 8 5 8 4 5 8 9 6 2.0 5 0 440 4.9 5.9 92..5 4. 2. 46.4.50 25 500 5 00 8 5 8 5 8 4 5 8 9 6 2.20 5 0 440 4.9 5.9 92..5 4. 2. 46.4.45 25 500 5 00 2 4 5 8 9 6 2 8 4.0 6 900 4 20 8.9 6. 0.6 0.2 4. 2. 54.2 2.00 0 00 9 000 4 25 4 8 5 5 8 5 8 9 6 2 5.60 890 5 220 44.5 9.8. 42.9 5.9 4.0 56.6 2.55 5 00 2 200 Shaft Flange Unit d Designation A A 2 J L N G T Weight Dynamic C Static C 0 mm in in in in in in in lb lbf lbf mm mm mm mm mm mm mm kg N N 20 Z4F20ZM 5 8 8 2 8 6 8.5 2 860 40 28.6 5.9 6.5 85.. 0.0 8.8 0.6 2 00 6 550 25 Z4F25ZM 0 Z4F0ZM 5 Z4F5ZM 40 Z4F40ZM 6 5 8 2 4 4 6.80 50 50 0.2 5.9 69.9 95. 2..0 8.8 0.82 4 000 800 9 9 4 4 4 6 2 2.65 4 80 2 520 2.5 5. 82.6 08.0 2..0 42.2.20 9 500 200 8 5 8 5 8 4 5 8 9 6 2.0 5 0 440 4.9 5.9 92..5 4. 2. 46.4.50 25 500 5 00 2 4 5 8 9 6 2 8 4.0 6 900 4 20 8.9 6. 0.6 0.2 4. 2. 54.2 2.00 0 00 9 000 * Metric units are supplied through the Made To Order (MTO) Program MRC Marathon Series Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. 24

ZTB ZMaRC Coated Cast Iron Tapped Base Units ZMaRC-Coated Insert Bearing HD i Series For Inch Shafts 4 5 6 Shaft Tapped-Base Unit d Designation A H H J L F G S Weight Dynamic C Static C 0 in in in in in in in in in lb lbf lbf mm mm mm mm mm mm mm mm kg N N 4 ZTB02ZM 2 9 6 5 6 2 2 8.80 2 860 40 8 8. 65.. 50.8 9.4 2. 6 8. 0.82 2 00 6 550 5 6 ZTB05ZM ZTB00ZM 8 ZTB02ZM 6 ZTB0ZM 4 ZTB04ZMR 4 ZTB04ZM 6 ZTB0ZM ZTB08ZM 2 6 6 2 25 2.05 50 50 8 8..4 6.5 50.8 6.2 2. 6 9.8 0.9 4 000 800 2 6 6 2 25 2.00 50 50 8 8..4 6.5 50.8 6.2 2. 6 9.8 0.9 4 000 800 8 6 4 5 8 8.50 4 80 2 520 6 8. 85. 42.9 6.2 0.6 5.9 4 22.2.59 9 500 200 8 6 4 5 8 8.50 4 80 2 520 6 8. 85. 42.9 6.2 0.6 5.9 4 22.2.59 9 500 200 8 6 4 5 8 8.50 4 80 2 520 6 8. 85. 42.9 6.2 0.6 5.9 4 22.2.59 9 500 200 8 4 8 4 4 4 4 4.50 5 0 440 4.6 95. 4.6 82.6 08.0 9. 25.4 2.05 25 500 5 00 8 4 8 4 4 4 4 4.50 5 0 440 4.6 95. 4.6 82.6 08.0 9. 25.4 2.05 25 500 5 00 8 5 6 5 6 4 5 8 4 6 6.00 6 900 4 20 4.6 00.0 49.2 88.9.5 9. 0.0 2. 0 00 9 000 5 2 4 6 ZTB5ZM 8 2 4 4 5 8 50.8.5 5.2 0.6 9. 22.2 5 8 9 2.6 8.00.64 890 5 00 5 220 2 200 For Metric Shafts 20mm 40mm* Shaft Tapped-Base Unit d Designation A H H J L F G S Weight Dynamic C Static C 0 mm in in in in in in in in lb lbf lbf mm mm mm mm mm mm mm mm kg N N 20 ZTB20ZM 2 9 6 5 6 2 2 8.80 2 860 40 8 8. 65.. 50.8 9.4 2. 6 8. 0.82 2 00 6 550 25 ZTB25ZM 0 ZTB0ZM 5 ZTB5ZM 40 ZTB40ZM 2 6 6 2 25 2.00 50 50 8 8..4 6.5 50.8 6.2 2. 6 9.8 0.9 4 000 800 8 6 4 5 8 8.50 4 80 2 520 6 8. 85. 42.9 6.2 0.6 5.9 4 22.2.59 9 500 200 8 4 8 4 4 4 4 4.50 5 0 440 4.6 95. 4.6 82.6 08.0 9. 25.4 2.05 25 500 5 00 8 5 6 5 6 4 5 8 4 6 6.00 6 900 4 20 4.6 00.0 49.2 88.9.5 9. 0.0 2. 0 00 9 000 * Metric units are supplied through the Made To Order (MTO) Program MRC Marathon Series Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings 25

SPB Cast Stainless Steel Pillow Block Units Stainless Steel Insert Bearing XD s Series For Inch Shafts /4 /2 Shaft Pillow J J Block d Designation A A H H H 2 Min Max L N N G S Dynamic C Static C o in in in in in in in in in in in in in lbf lbf mm mm mm mm mm mm mm mm mm mm mm mm N N /4 SPB02SS /4 /4 2 /2 5 5 /6 /64 /6 4 /6 5 2 /6 /64 /8 /2 2 400 40 2.0 9.0 64.0. 4.0 8. 06.4 2.0 20.5.5 0.0 8. 0 800 6 550 SPB00SS /6 SPB0SS /6 /8 2 /4 5 /6 /8 /6 4 5 /6 5 25 /8 /4 /64 /8 /2 2 00 50 6.0 22.0 0.0 6.5 6.0 9. 09.5 0.0 9..5 0.0 9.8 900 800 9 /6 5 /64 2 /6 /2 4 5 /4 5 6 9 /6 /6 /2 /8 00 2 520 9. 25.4 82.0 42.9 6.5 08.0 2.0 52.4 2.8 4. 2. 22.2 6 00 200 /4 SPB04SSR 9 /6 5 /64 2 /6 /2 4 5 /4 5 6 9 /6 /6 /2 /8 00 2 520 9. 25.4 82.0 42.9 6.5 08.0 2.0 52.4 2.8 4. 2. 22.2 6 00 200 /4 SPB04SS /8 SPB06SS /6 SPB0SS / 2 SPB08SS /4 /8 2 /2 /8 /4 4 /6 5 /4 6 5 2 9 /6 /2 /6 /2 4 900 440 44.5 28.6 9.0 4.6 9.0 9..4 60. 2.4 4. 2. 25.4 2 600 5 00 /4 /8 2 /2 /8 /4 4 /6 5 /4 6 5 2 9 /6 /2 /6 /2 4 900 440 44.5 28.6 9.0 4.6 9.0 9..4 60. 2.4 4. 2. 25.4 2 600 5 00 /4 /8 2 /2 /8 /4 4 /6 5 /4 6 5 2 9 /6 /2 /6 /2 4 900 440 44.5 28.6 9.0 4.6 9.0 9..4 60. 2.4 4. 2. 25.4 2 600 5 00 /8 /4 /2 5 /6 /4 4 5 /6 5 /4 6 9 /8 /2 /6 /2 /6 5 600 4 20 4.6.2 99.0 49.2 9.0 25.4 46.0 4.6 24.6 4. 2. 0.0 24 00 9 000 For Metric Shafts 20mm 40mm* Shaft Pillow J J Block d Designation A A H H H 2 Min Max L N N G S Dynamic C Static C o mm in in in in in in in in in in in in lbf lbf mm mm mm mm mm mm mm mm mm mm mm mm N N 20 SPB20SS /4 /4 2 /2 5 5 /6 /64 /6 4 /6 5 2 /6 /64 /8 /2 2 400 40 2.0 9.0 64.0. 4.0 8. 06.4 2.0 20.5.5 0.0 8. 0 800 6 550 25 SPB25SS 0 SPB0SS 5 SPB5SS 40 SPB40SS /6 /8 2 /4 5 /6 /8 /6 4 5 /6 5 25 /8 /4 /64 /8 /2 2 00 50 6.0 22.0 0.0 6.5 6.0 9. 09.5 0.0 9..5 0.0 9.8 900 800 9 /6 5 /64 2 /6 /2 4 5 /4 5 6 9 /6 /6 /2 /8 00 2 520 9. 25.4 82.0 42.9 6.5 08.0 2.0 52.4 2.8 4. 2. 22.2 6 00 200 /4 /8 2 /2 /8 /4 4 /6 5 /4 6 5 2 9 /6 /2 /6 /2 4 900 440 44.5 28.6 9.0 4.6 9.0 9..4 60. 2.4 4. 2. 25.4 2 600 5 00 /8 /4 /2 5 /6 /4 4 5 /6 5 /4 6 9 /8 /2 /6 /2 /6 5 600 4 20 4.6.2 99.0 49.2 9.0 25.4 46.0 4.6 24.6 4. 2. 0.0 24 00 9 000 * Metric units are supplied through the Made To Order (MTO) Program MRC Marathon Series Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. 26

S2F Cast Stainless Steel Two-Bolt Flange Units Stainless Steel Insert Bearing XD s Series For Inch Shafts /4 /2 Shaft Flange Unit d Designation A A 2 H J L N G T Dynamic C Static C o in in in in in in in in in lbf lbf mm mm mm mm mm mm mm mm N N /4 S2F02SS /64 /6 4 /2 /2 2 /8 /6 /8 9 /2 2 400 40 25.8..9 89. 60.. 0.0 2.5 0 800 6 550 S2F00SS /6 S2F0SS /4 S2F04SSR /4 S2F04SS /8 S2F06SS /6 S2F0SS /2 S2F08SS 5 /2 /2 4 /8 5 /64 2 /4 /2 /6 /6 2 00 50.4.5 2.4 98.8 69.9 2..0 6.5 900 800 /2 /2 5 9 /6 4 9 /2 /8 /2 /6 2 /2 00 2 520 4..5 4. 6. 9.4 2..0 42. 6 00 200 /2 /2 5 9 /6 4 9 /2 /8 /2 /6 2 /2 00 2 520 4..5 4. 6. 9.4 2..0 42. 6 00 200 /2 9 /6 6 /8 5 /8 5 /8 9 /6 /2 /6 4 900 440 5. 4. 55.6 0.2 92. 4. 2. 46.0 2 600 5 00 /2 9 /6 6 /8 5 /8 5 /8 9 /6 /2 /6 4 900 440 5. 4. 55.6 0.2 92. 4. 2. 46.0 2 600 5 00 /2 9 /6 6 /8 5 /8 5 /8 9 /6 /2 /6 4 900 440 5. 4. 55.6 0.2 92. 4. 2. 46.0 2 600 5 00 /2 9 /6 6 /4 5 2 /2 4 9 /6 /2 2 /2 5 600 4 20 8.9 4..5 4. 0.6 4. 2. 5.0 24 00 9 000 For Metric Shafts 20mm 40mm* Shaft Flange Unit d Designation A A 2 H J L N G T Dynamic C Static Co mm in in in in in in in in lbf lbf mm mm mm mm mm mm mm mm N N 20 S2F20SS /64 /6 4 /2 /2 2 /8 /6 /8 9 /2 2 400 40 25.8..9 89. 60.. 0.0 2.5 0 800 6 550 25 S2F25SS 0 S2F0SS 5 S2F5SS 40 S2F40SS 5 /2 /2 4 /8 5 /64 2 /4 /2 /6 /6 2 00 50.4.5 2.4 98.8 69.9 2..0 6.5 900 800 /2 /2 5 9 /6 4 9 /2 /8 /2 /6 2 /2 00 2 520 4..5 4. 6. 9.4 2..0 42. 6 00 200 /2 9 /6 6 /8 5 /8 5 /8 9 /6 /2 /6 4 900 440 5. 4. 55.6 0.2 92. 4. 2. 46.0 2 600 5 00 /2 9 /6 6 /4 5 2 /2 4 9 /6 /2 2 /2 5 600 4 20 8.9 4..5 4. 0.6 4. 2. 5.0 24 00 9 000 * Metric units are supplied through the Made To Order (MTO) Program MRC Marathon Series Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings 2

S4F Cast Stainless Steel Four-Bolt Flange Units Stainless Steel Insert Bearing XD s Series For Inch Shafts /4 /2 Shaft Flange Unit d Designation A A 2 J L N G T Dynamic C Static C o in in in in in in in in lbf lbf mm mm mm mm mm mm mm N N /4 S4F02SS /64 /6 2 /2 /8 /6 /8 5 /2 2 400 40 25.8. 6.5 85.. 0.0. 0 800 6 550 S4F00SS /6 S4F0SS /4 S4F04SSR /4 S4F04SS /8 S4F06SS /6 S4F0SS /2 S4F08SS 5 /2 /2 2 /4 /4 /64 /6 /2 2 00 50.4.5 69.9 95..5.0 8.9 900 800 /2 /2 /4 4 /4 /2 /6 2 /2 00 2 520 4..5 82.6 08.0 2..0 42. 6 00 200 /2 /2 /4 4 /4 /2 /6 2 /2 00 2 520 4..5 82.6 08.0 2..0 42. 6 00 200 /2 9 /6 5 /8 4 5 /8 9 /6 /2 /6 4 900 440 5. 4. 92..5 4. 2. 46.0 2 600 5 00 /2 9 /6 5 /8 4 5 /8 9 /6 /2 /6 4 900 440 5. 4. 92..5 4. 2. 46.0 2 600 5 00 /2 9 /6 5 /8 4 5 /8 9 /6 /2 /6 4 900 440 5. 4. 92..5 4. 2. 46.0 2 600 5 00 /2 9 /6 4 5 /8 9 /6 /2 2 /2 5 600 4 20 8.9 4. 0.6 0.2 4. 2. 5.2 24 00 9 000 For Metric Shafts 20mm 40mm* Shaft Flange Unit d Designation A A 2 J L N G T Dynamic C Static C o mm in in in in in in in lbf lbf mm mm mm mm mm mm mm N N 20 S4F20SS /64 /6 2 /2 /8 /6 /8 5 /2 2 400 40 25.8. 6.5 85.. 0.0. 0 800 6 550 25 S4F25SS 0 S4F0SS 5 S4F5SS 40 S4F40SS 5 /2 /2 2 /4 /4 /64 /6 /2 2 00 50.4.5 69.9 95..5.0 8.9 900 800 /2 /2 /4 4 /4 /2 /6 2 /2 00 2 520 4..5 82.6 08.0 2..0 42. 6 00 200 /2 9 /6 5 /8 4 5 /8 9 /6 /2 /6 4 900 440 5. 4. 92..5 4. 2. 46.0 2 600 5 00 /2 9 /6 4 5 /8 9 /6 /2 2 /2 5 600 4 20 8.9 4. 0.6 0.2 4. 2. 5.2 24 00 9 000 * Metric units are supplied through the Made To Order (MTO) Program MRC Marathon Series Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. 28

STB Cast Stainless Steel Tapped Base Units Stainless Steel Insert Bearing XD s Series For Inch Shafts /4 /2 Shaft Tapped-Base Unit d Designation A H H J L F G S Dynamic C Static C o in in in in in in in UNC in lbf lbf mm mm mm mm mm mm Threads mm N N /4 STB02SS /8 2 /2 5 /6 2 2 5 2 /8 /2 /2 /8 6 2 400 40 28.6 6.5. 50.8 66. 2. 8. 0 800 6 550 STB00SS /6 STB0SS /4 STB04SSR /4 STB04SS /8 STB06SS /6 STB0SS /2 STB08SS /4 2 /4 /6 2 25 /2 /2 /8 6 2 00 50.8 69.9 6.5 50.8 6.2 2. 9.8 900 800 /2 /4 /6 5 /8 /8 /8 /6 4 00 2 520 8. 82.6 42.9 6.2 98.4 5.9 22.2 6 00 200 /2 /4 /6 5 /8 /8 /8 /6 4 00 2 520 8. 82.6 42.9 6.2 98.4 5.9 22.2 6 00 200 /2 5 /8 /8 /4 4 /8 /4 /2 4 900 440 8. 92. 4.6 82.6 04.8 9. 25.4 2 600 5 00 /2 5 /8 /8 /4 4 /8 /4 /2 4 900 440 8. 92. 4.6 82.6 04.8 9. 25.4 2 600 5 00 /2 5 /8 /8 /4 4 /8 /4 /2 4 900 440 8. 92. 4.6 82.6 04.8 9. 25.4 2 600 5 00 5 /8 5 /6 5 /6 /2 4 /2 /4 /2 /6 5 600 4 20 4. 00.0 49.2 88.9 4. 9. 0.0 24 00 9 000 For Metric Shafts 20mm 40mm* Shaft Tapped-Base Unit d Designation A H H J L F G S Dynamic C Static C o mm in in in in in in UNC in lbf lbf mm mm mm mm mm mm Threads mm N N 20 STB20SS /8 2 /2 5 /6 2 2 5 2 /8 /2 /2 /8 6 2 400 40 28.6 6.5. 50.8 66. 2. 8. 0 800 6 550 25 STB25SS 0 STB0SS 5 STB5SS 40 STB40SS /4 2 /4 /6 2 25 /2 /2 /8 6 2 00 50.8 69.9 6.5 50.8 6.2 2. 9.8 900 800 /2 /4 /6 5 /8 /8 /8 /6 4 00 2 520 8. 82.6 42.9 6.2 98.4 5.9 22.2 6 00 200 /2 5 /8 /8 /4 4 /8 /4 /2 4 900 440 8. 92. 4.6 82.6 04.8 9. 25.4 2 600 5 00 5 /8 5 /6 5 /6 /2 4 /2 /4 /2 /6 5 600 4 20 4. 00.0 49.2 88.9 4. 9. 0.0 24 00 9 000 * Metric units are supplied through the Made To Order (MTO) Program MRC Marathon Series Mounted Bearing Units are greased and sealed for life. MRC does not recommend regreasing. If required, units with relubrication fittings are available for your application. Adding a G suffix to the part number denotes a regreasable unit. Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings

Mounted Unit ZMaRC-Coated Insert Bearings Set Screw Locking C SET SCREW D B d d s For Inch Shafts 4 5 6 Insert Bearing Bore Outside Inner Width Outer Width Max Fillet Set Screw Designation d D B C Dynamic C Static C 0 d S Rad.() Size Weight in in in in lbf lbf in in in lb mm mm mm mm N N mm mm mm inch kg 4.8504.220 0.552 2 860 40.0 0.500 0.024 RRZ02BRR 9.05 4 4 2 00 6 500 28.20 2.0 0.60 4-28 x 6 0. 0.4 5 6 2.042.4 0.5906 50 50.28 0.56 0.024 RRZ05BRR 2.8 52 4.0 5 4 000 800.4 4.0 0.60 4-28 x 6 0.42 0.9 RRZ00BRR 25.4 2.042 52.4 4.0 0.5906 5 50 4 000 50 800.28.4 0.56 4.0 0.024 0.60 4-28 x 6 0. 0. RRZ02BRR RRZ0BRR RRZ04BRR2 RRZ04BRR RRZ0BRR RRZ08BRR RRZ5BRR 8 2.4409.500 0.08 4 80 2 520.56 0.626 0.024 0.66 4-28 x 6 28.58 62 8.0 8 9 500 200 9.0 5.90 0.60 0.0 6 2.4409.500 0.08 4 80 2 520.56 0.626 0.024 0.60 4-28 x 6 0.6 62 8.0 8 9 500 200 9.0 5.90 0.60 0.2 4 2.4409.500 0.08 4 80 2 520.56 0.626 0.024 0.55 4-28 x 6.5 62 8.0 8 9 500 200 9.0 5.90 0.60 0.25 4 2.846.688 0.480 5 0 440.85 0.689 0.09 5 6-24 x 5 6.00.5 2 42.88 9 25 500 5 00 46.0.50.00 0.46 6 2.846.688 0.480 5 0 440.85 0.689 0.09 5 6-24 x 5 6 0.84 6.5 2 42.88 9 25 500 5 00 46.0.50.00 0.8.496.98 0.8268 6 900 4 20 2.09 0.48 0.09 5 6-24 x 5 6.0 8.0 80 49.2 2 0 00 9 000 5.80 9.00 0.59 5 6.54 2.0 0.866 890 5 220 2.46 0.48 0.09.55 8-24 x 5 6 49.20 90 5.60 22 5 00 2 200 62.5 9.00 0. For Metric Shafts 20 mm 40 mm Insert Bearing Bore Outside Inner Width Outer Width Max Fillet Set Screw Designation d D B C Dynamic C Static C 0 d S Rad.() Size Weight in in in in lbf lbf in in in lb mm mm mm mm N N mm mm mm mm kg RRZ20BRR 0.84 20.8504 4.220 0.552 4 2 860 2 00 40 6 550.0 28.20 0.500 2.0 0.024 0.60 M6 x 0.5 x 5 0.4 0. RRZ25BRR RRZ0BRR RRZ5BRR 0.984 2.042.4 0.5906 50 50.28 0.56 0.024 25 52 4. 5 4 000 800.4 4.0 0.60 M6 x 0.5 x 5 0.8 0.40.8 2.4409.500 0.08 4 80 2 520.56 0.626 0.024 0 62 8. 8 9 500 200 9.0 5.90 0.60 M6 x 0.5 x 5 0.2 0.60.80 2.846.688 0.480 5 0 440.85 0.689 0.09 5 2 42.9 9 25 500 5 00 46.0.50.00 M6 x 0.5 x 5 0.46.00.548.496.98 0.480 6 900 4 20 2.09 0.48 0.09.20 RRZ40BRR 40 80 49.2 9 0 00 9 000 5.80 9.00 M8 x x 0.55 () Fillet radius indicates the maximum fillet radius on the shaft which bearing corner will clear. 0

Mounted Unit Stainless Steel Insert Bearings Set Screw Locking C SET SCREW D B d d s For Inch Shafts 4 Insert Bearing Bore Outside Inner Width Outer Width Max Fillet Set Screw Designation d D B C Dynamic C Static C 0 d S Rad.() Size Weight in in in in lbf lbf in in in lb mm mm mm mm N N mm mm mm inch kg RRH02BRR 4 9.05.8504 4.220 0.552 4 2 80 0 600 40 6 500.0 28.20 0.500 2.0 0.024 0.60 4-28 x 6 0. 0.4 RRH00BRR 2.042.4 0.5906 2 520 50.28 0.56 0.024 0. 4-28 x 6 25.4 52 4.0 5 200 800.4 4.0 0.60 0. RRH0BRR 6 2.4409.500 0.08 50 2 520.56 0.626 0.024 0.60 4-28 x 6 0.6 62 8.0 8 5 600 200 9.0 5.90 0.60 0.2 RRH04BRR2 4 2.4409.500 0.08 4 560 440.56 0.626 0.024 0.55 4-28 x 6.5 62 8.0 8 20 00 5 00 9.0 5.90 0.60 0.25 RRH04BRR 4 2.846.688 0.480 4 560 440.85 0.689 0.09 5.00 6-24 x 5 6.5 2 42.88 9 20 00 5 00 46.0.50.00 0.46 RRH06BRR 8 2.846.688 0.480 4 560 440.85 0.689 0.09 5 0.90 6-24 x 5 6 4.9 2 42.88 9 20 00 5 00 46.0.50.00 0.4 RRH0BRR 6 2.846.688 0.480 4 560 440.85 0.689 0.09 5 0.84 6-24 x 5 6 6.5 2 42.88 9 20 00 5 00 46.0.50.00 0.8 RRH08BRR.496.98 0.8268 5 550 4 20 2.09 0.48 0.09 5.0 6-24 x 5 6 8.0 80 49.2 2 24 00 9 000 5.80 9.00.00 0.59 For Metric Shafts 20 mm 40 mm Insert Bearing Bore Outside Inner Width Outer Width Max Fillet Set Screw Designation d D B C Dynamic C Static C 0 d S Rad.() Size Weight in in in in lbf lbf in in in lb mm mm mm mm N N mm mm mm mm kg RRH20BRR 0.84 20.8504 4.220 0.552 4 2 80 0 600 40 6 550.0 28.20 0.500 2.0 0.024 0.60 M6 x 0.5 x 5 0.4 0. RRH25BRR RRH0BRR RRH5BRR 0.984 2.042.4 0.5906 2 520 50.28 0.56 0.024 25 52 4. 5 200 800.4 4.0 0.60 M6 x 0.5 x 5 0.8 0.40.8 2.4409.500 0.08 50 2 520.56 0.626 0.024 M6 x 0.5 x 5 0.60 0 62 8. 8 5 600 200 9.0 5.90 0.60 0.2.80 2.846.688 0.480 4 560 440.85 0.689 0.09 5 2 42.9 9 20 00 5 00 46.0.50.00 M6 x 0.5 x 5 0.46.00.548.496.98 0.480 5 550 4 20 2.09 0.48 0.09.20 RRH40BRR 40 80 49.2 9 24 00 9 000 5.80 9.00 M8 x x 0.55 () Fillet radius indicates the maximum fillet radius on the shaft which bearing corner will clear. Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings

Marathon Hi-Temp and Submersible Units MRC Hi-Temp and Submersible Units are fitted with high performance plane bearing inserts specifically designed for these demanding applications. The inserts can be assembled into any of the Marathon housing styles which MRC currently offers. Rotation of the insert in the housing is prevented by means of an anti-rotation slot in the outer ring mating with the set screw inserted into the housing, while still allowing self-aligning capability. These units provide superior performance in applications which would normally cause premature failure of standard anti-friction bearings requiring lubrication. As with all Marathon products, these units provide improved service life, and do not require lubrication since the polymer is the friction reducing component. Therefore, they are maintenance free and there is no excessive grease purging, which is usually an issue when trying to extend the service life of a bearing in severe operating environments. Marathon High Temp and Submersible Plane Bearing Units are suitable for a wide range of applications in addition to high temp and submersible conditions. They meet USDA approval for direct contact in meat, poultry and dairy applications, and are suitable for a wide range of food applications where washdown and corrosion are problems. Marathon Plane Bearing Units Marathon plane bearing inserts meet many food and non-food application requirements. They are suitable for a wide range of food applications where corrosion is a problem; they can be selected to operate in temperature ranges from cryogenic to 600 F and can be mounted horizontally or vertically; they can also be supplied to handle different loading and speed conditions. And as with all Marathon inserts, lubrication is not required, resulting in simplified maintenance-free operation. Non-stock plane bearing units can be supplied through the MRC Made-To-Order (MTO) program. The normal lead time for a non-stocked variant is approximately six weeks. Submersible part number examples: '' Composite pillow block CPB00SB 6'' Composite 2-bolt flange C2F0SB '' Composite tapped base CTB08SB High temparture part number examples: '' ZMaRC cast iron pillow block ZPB00HT 6'' ZZMaRC cast iron 2-bolt flange Z2F0HT '' ZMaRC cast iron 4-bolt flange Z4F08HT Submersible part number examples: '' Stainless pillow block SPB00SB 6'' Stainless 2-bolt flange S2F0SB High temparture part number examples: '' Stainless pillow block SPB00HT 6'' Stainless 2-bolt flange S2F0HT 2

High Temperature Insert Plane Bearings (HT) Set Screw Locking MRC High Temperature Plane Bearing Inserts can withstand consistant temperatures up to 500 F. When normal anti-friction bearings cannot handle the heat, MRC High Temperature Plane Bearings are the best choice to keep rotating equipment running smoothly. The 6 stainless steel inner ring and 04 stainless steel outer ring offer wear resistance as well as corrosion resistance. The high performance polymer sleeve material allows the bearing to operate at higher speeds compared to typical plane bearings. Since the polymer material is the friction reducing component, no grease is required for proper performance. In the event of premature wear, the insert bearing will not catastrophically fail but will exhibit looseness, indicating that the bearing needs to be replaced. The recommended Marathon housing material for this insert is either the ZMaRC -coated cast iron or cast stainless steel to meet most application requirements for high temperature duty. In addition, the insert bearing is approved for incidental food contact by the USDA/FDA. For inch shafts 4 to 5 6. Metric inserts can be supplied through the MTO Program. Insert Shaft Maximum Maximum Radial Load (Fr) Bearing Designation d D B C S Speed* Load* x Speed (n)* Weight in in in in in lb mm mm mm mm mm rpm lbs. lbs. x rpm kg RRS02BBL 4.8504.484 0.9 0.560 2 000 2 00 9 000 0.5 9. 4.0. 2.4 4. 0.2 RRS00BBL 2.042.542 0.9 0.6260 500 000 90 000 0. 25.4 52.0 9. 2.4 5.9 0.2 RRS02BBL 8 2.4409.80.08 0.50 50 4 000 226 000. 28.6 62.0 46.5 2.4 9. 0.50 RRS0BBL 6 2.4409.80.08 0.50 50 4 000 226 000. 0.2 62.0 46.5 2.4 9. 0.50 RRS04BBL2 4 2.4409.80.08 0.50 50 4 000 226 000..8 62.0 46.5 2.4 9. 0.50 RRS04BBL 4 2.846 2.042.02 0.95 200 5 00 262 000..8 2.0 52.0 28.2 2.8 0. RRS0BBL 6 2.846 2.042.02 0.95 200 5 00 262 000. 6.5 2.0 52.0 28.2 2.8 0. RRS08BBL.496 2.22.268 0.9685 000 6 00 286 000 2.5 8. 80.0 56. 2. 24.6.4 RRS5BBL 5 6.54 2.5.268.05 800 9 000 8 000. 49.2 90.0 58. 2. 26.2.50 *Plane bearing capacity is based on the heat generation which is directly related to speed versus applied load. The "radial load x speed" column above provides the relationship between load versus speed in order to evaluate the bearing suitability. If the application conditions exceed any of the three factors above, different polymer materials can be selected to meet the application needs. Example for an RRS00BBL insert bearing. If the applied load on the bearing is 200 lbs, then based on a "Radial (Fr) x Speed (n)" factor of 90,000, the bearing can rotate up to 950 rpm. Fr x n = 90,000 Fr = 200 lbs Therefore: 90,000 / 200 = 950 rpm Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings

Submersible Insert Plane Bearings (SB) Set Screw Locking MRC Submersible Plane Bearing Inserts are suitable for applications which are constantly exposed to or submerged in moisture. When normal anti-friction bearings fail because of grease washout or corrosion, MRC Submersible Plane Bearings are the best choice to keep rotating equipment running smoothly. The 6 stainless steel inner sleeve offers wear resistance as well as corrosion resistance. The high performance polymer outer ring allows the bearing to operate at moderate speeds without the need for lubrication since the polymer material is self lubricated. The polymer material can withstand continuous temperatures up to 50 F, and tolerates higher temperatures during washdown. The insert bearing will not catastrophically fail; it wears by becoming loose in the bore. The recommended Marathon housing material for this insert is either composite or cast stainless steel. In addition, the insert bearing is approved for direct food contact by the USDA / FDA. For inch shafts 4 to 5 6. Metric inserts can be supplied through the MTO Program. Insert Shaft Maximum Maximum Radial Load (Fr) Bearing Designation d D B C S Speed* Load* x Speed (n) * Weight in in in in in lb mm mm mm mm mm rpm lbs. lbs. x rpm kg RRP02BPL 4.8504.484 0.9 0.560 250 625 900 0. 9. 4.0. 2.4 4. 0.4 RRP00BPL 2.042.542 0.9 0.6260 90 85 4 200 0.4 25.4 52.0 9. 2.4 5.9 0.8 RRP02BPL 8 2.4409.80.08 0.50 50 50 4 900 0.6 28.6 62.0 46.5 2.4 9. 0.2 RRP0BPL 6 2.4409.80.08 0.50 50 50 4 900 0.6 0.2 62.0 46.5 2.4 9. 0.2 RRP04BPL2 4 2.4409.80.08 0.50 50 50 4 900 0.6.8 62.0 46.5 2.4 9. 0.2 RRP04BPL 4 2.846 2.042.02 0.95 0 450 5 600 0.8.8 2.0 52.0 28.2 2.8 0.6 RRP0BPL 6 2.846 2.042.02 0.95 0 450 5 600 0.8 6.5 2.0 52.0 28.2 2.8 0.6 RRP08BPL.496 2.22.268 0.9685 20 900 6 00.0 8. 80.0 56. 2. 24.6 0.45 RRP5BPL 5 6.54 2.5.268.05 00 2 500 6 00. 49.2 90.0 58. 2. 26.2 0.59 *Plane bearing capacity is based on the heat generation which is directly related to speed versus applied load. The radial load x speed column above provides the relationship between load versus speed in order to evaluate the bearing suitability. If the application conditions exceed any of the three factors above, different polymer materials can be selected to meet the application needs. Example for an RRP00BPL insert bearing. If the applied load on the bearing is 40 lbs, then based on a Radial (Fr) x Speed (n) factor of 4200, the bearing can rotate up to 05 rpm. Fr x n = 4200 Fr = 40 lbs Therefore: 4200 / 40 = 05 rpm 4

Made-To-Order Products for the Food Processing Industry Low Backing Height Pillow Block (CPL ZM or SS) Size range: 4 inches, 20 mm 40 mm Insert bearing: ZMaRC-coated or stainless steel These units have a lower backing height than standard pillow blocks while the base bolt center distance, bolt size, insert bearing and load ratings remain the same. The overall height and base thickness are slightly smaller. These units are non-regreasable but can be furnished with grease fittings on special order. A regreasable unit is denoted by adding a G suffix to the unit part number. Mounting and center height interchangeable with the following: AMI UCLP Dodge P2B-SC Fafnir YAK Hub City PB250 Link Belt PL McGill CL-25 Sealmaster NPL Low Profile 2-Bolt Flange Unit (C2L ZM or SS) Size range: 4 6 inches, 20 mm 5 mm Insert bearing: ZMaRC-coated or stainless steel These units are smaller than a standard 2-bolt flange unit but have the same insert bearing and load ratings.they are used where space is limited. The housing bolt holes are round to accept round machine bolts. They are nonregreasable but can be furnished with grease fittings on special order. A regreasable unit is denoted by adding a G suffix to the unit part number. Mounting interchangeable with the following: Dodge LFT-SC Hub City FB60 McGill FBS2-25 Hanger Units (SHU SS) Size range: 4 inches, 20 mm 40 mm Insert bearing: Stainless steel These units are used on screw conveyors and include a stainless steel housing tapped for a straight pipe thread. These units are non-regreasable but grease fittings can be furnished on special order. A regreasable unit is denoted by adding a G suffix to the unit part number. Mounting interchangeable with the following: AMI Dodge McGill Sealmaster UCECH, UCHPL SCHB MCHB SCHB Low Profile -Bolt Flange Unit (CF ZM or SS) Size range: 4 6 inches, 20 mm 5 mm Insert bearing: ZMaRC-Coated or Stainless Steel These units are non-regreasable and are applied where space constraints require a compact unit with sufficient strength for the application. The insert bearing and load ratings are the same as a standard unit with the same shaft diameter. The housing bolt holes are round to accept round machine bolts. A grease fitting can be furnished on special order. A regreasable unit is denoted by adding a G suffix to the unit part number. Mounting interchangeable with the following: AMI BTM Dodge LF-SC Hub City FBI50 Sealmaster LF 4-Bolt Piloted Flange Unit (CPF ZM or SS) Size range: 4 inches, 20 mm 40 mm Insert bearing: ZMaRC-coated or stainless steel These are non-regreasable units which have an accurately machined piloting diameter to position the unit in the bore of the mounting surface, eliminating the need for any additional adjustments. The insert bearings and load ratings are the same as standard units with the same shaft diameter. A grease fitting can be furnished on special order. A regreasable unit is denoted by adding a G suffix to the unit part number. Mounting interchangeable with the following: AMI UCFCS Dodge FC-SC Hub City FC50 McGill PFC4-25 Sealmaster SFC Other shaft sizes may be available on special order. Contact MRC at -800-MRC-000 regarding pricing, availability or technical service for all Marathon Series products, or for information on regreasable units. Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings 5

Marathon Series Nomenclature Inches: First Digit: Number of inches Second and third digits: Number of sixteenths of an inch Example: 0 indicates /6 (unit) Metric: First two digits: Number of millimeters Example: 25 would indicate 25 millimeters SHAFT SIZE CPB 0 ZM HOUSING INSERT BEARING CPB Gray composite pillow block ZPB ZMaRC-coated cast iron pillow block SPB Cast stainless steel pillow block C2F Gray composite 2-bolt flange Z2F ZMaRC coated cast iron 2-bolt flange S2F Cast stainless steel 2-bolt flange C4F Gray composite 4-bolt flange Z4F ZMaRC- coated cast iron 4-bolt flange S4F Cast stainless steel 4-bolt flange CTB Gray composite tapped-base pillow block ZTB ZMaRC-coated cast iron tapped-base pillow block STB Cast stainless steel tapped-base pillow block CBF Gray composite -bolt bracket flange CTN Gray composite narrow-slot take-up CTW Gray composite wide-slot take-up ZM ZMaRC-coated SS Stainless steel G Relubricatable bearing unit ZMR ZMaRC-coated insert bearing, with a /4" bore, fitted into a housing that usually accommodates a /6" insert bearing SSR Stainless steel insert bearing, with a /4" bore, fitted into a housing that usually accommodates a /6" insert bearing HT High temparture plane bearing SB Submersible plane bearing HTR High temparture insert bearing with a 4 bore, fitted into a housing that usually accomodates a 6 insert bearing. SBR Submersible insert bearing with a 4 bore, fitted into a housing that usually accodomates a 6 insert bearing 6

Picker Hub Applications Stainless Steel Bearings with Solid Lubricant Pack (W64F) Single row deep groove (SRDG), doubled sealed, stainless steel ball bearings are available with solid lubricant pack in a food grade formulation identified as W64F. This lubricant is USDA approved for use in food related applications with incidental food contact. It has excellent oil lubricating properties and helps prevent grease washout and contamination under harsh operating conditions. This lubricant pack combined with stainless steel bearing components and synthetic rubber seals, provides a significant increase in bearing life in these applications. Stainless steel single row, deep groove ball bearings packed with W64F solid lubricant are available from stock in five sizes, as shown in the table below. In addition to the suffix ST to denote stainless steel, a descriptive suffix -W64F is included to distinguish them from standard stainless steel bearings. Other sizes can be furnished on special order. For equivalent load and life calculations see page 54 and 55 in the MRC Engineering Handbook. Technical Data Maximum Operating Temperatures The temperature limits, measured on the bearing outside diameter are: Maximum continuous: 80 F (82 C) Maximum intermittent: 200 F (9 C) Load Ratings Load ratings for bearings lubricated with W64F solid lubricant are the same as for standard bearings. Speed Limits The speed limit Ndm, is dependent on the bearing bore and outside diameters, and RPM, in the following relationship: Nd m =RPM x (Bore + O.D.) 2 (bore, OD in mm) For double sealed or shielded, single row, deep groove, stainless steel ball bearings, the limiting value of Ndm is 240,000. It is important to note that as ambient or externally produced temperatures increase, the maximum operating speed may have to be reduced, to keep the bearing operating temperature within the maximum operating limit. As with most bearing lubricants, reducing bearing temperature adds to the capability of W64F. MRC Bearing Number Bore d mm in Outside meter D mm in Width B mm in Fillet Radius ) r a Zd 2 mm in mm in N Dynamic C 2) lbf N Static C 0 lbf 20SZZST-W64F.669 40.548 2.424.64.025 6.56 650 20 4 50 00 204SZZST-W64F 20.84 4.8504 4.552.0.040 50.8 0 200 2 280 6 550 40 205SZZST-W64F 25.984 52 2.042 5.5906.0.040 568.88 200 2 520 800 50 20SZZST-W64F 5.80 2 2.846.669.0.040 0.2 20 400 4 590 5 00 440 04SZZST-W64F 20.84 52 2.042 5.5906.0.040 62.98 2 00 2 860 800 50 ) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear. 2) Rating for one million revolutions or 500 hours at RPM. Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings

Marathon Series Product Range Stainless Steel Single Row Deep Groove (SRDG) Ball Bearings MRC stainless steel (SRDG) ball bearings are used in fish, poultry and other food processing applications. Examples of popular applications include automatic filleting and sizing equipment aboard fishing trawlers, and evisceration equipment in poultry plants. MRC stainless steel SRDG ball bearings exhibit significantly longer life than standard bearings in a wide range of demanding applications. All MRC stainless steel SRDG ball bearings can also be specified with a solid lubricant pack that prevents grease washout during washdowns and helps protect against contamination in harsh environments. For equivalent load and life calculations see page 54 and 55 in the MRC Engineering Handbook. FFST KSFFST SFFST Two Shields ZZST KSZZST SZZST Two Seals MRC Bearing Number Bore d mm in Outside meter D mm in Width B mm in Fillet Radius ) r a mm in Zd 2 mm in Dynamic C 2) N lbf Static C 0 N lbf Open and Shielded Grease RPM Speed Rating ) Single & Double Sealed Oil Grease RPM RPM 8ZZST 8.0.50 22.0.866.0.256.0.02 0. 2 600 585 60 06 6 000 4 000 2 000 R2ST.2.250 9.5.50 4.0.562.0.02 9.0 250 56 20 2 5 000 9 000 52 000 R2FFST.2.250 9.5.50 4.0.562.0.02 9.0 250 56 20 2 5 000 9 000 52 000 RFFST 4.8.85 2..5000 5.0.960.0.02 9.06 65 2 490 0 5 000 69 000 40 000 RZZST 4.8.85 2..5000 5.0.960.0.02 9.06 65 2 490 0 5 000 69 000 40 000 R4FFST 6.4.2500 5.9.6250 5.0.960.0.02 45.0 80 266 620 9 44 000 54 000 000 R6FFST 9.5.50 22.2.850..282.4.06 0. 2 660 59 40 0 000 8 000 2 000 R6ZZST 9.5.50 22.2.850..282.4.06 0. 2 660 59 40 0 000 8 000 2 000 R8ST 2..5000 28.6.250 6.4.2500.4.06 8.28 4 060 92 2 400 540 24 000 000 6 000 R8FFST 2..5000 28.6.250.9.25.4.06 8.28 4 060 92 2 400 540 24 000 000 6 000 R8ZZST 2..5000 28.6.250.9.25.4.06 8.28 4 060 92 2 400 540 24 000 000 6 000 R0ZZST 5.9.6250 4.9.50 8..48.9.0 226.5 4 840 090 250 8 000 22 000 000 R2FFST 9..500 4..6250..45.9.0 6.56 490 680 5 00 50 6 000 9 000 000 R2ZZST 9..500 4..6250..45.9.0 6.56 490 680 5 00 50 6 000 9 000 000 0KSZZST 2.0.424 28.0.024 8.0.25.0.02 8.28 4 060 92 2 60 50 26 000 2 000 000 02KSZZST 5.0.5906 2.0.2598 9.0.54.0.02 206.2 4 40 00 2 850 640 22 000 28 000 4 000 0KSZZST.0.669 5.0.80 0.0.9.0.02 226.5 4 840 090 250 0 9 000 24 000 000 04KSZZST 20.0.84 42.0.655 2.0.424.64.025 6.56 490 680 5 000 20 000 20 000 000 05KSZZST 25.0.984 4.0.8504 2.0.424.64.025 458. 8 960 2 00 6 550 40 5 000 8 000 9 500 06KSZZST 0.0.8 55.0 2.654.0.58.00.040 56.8 9 40 2 0 90 660 2 000 5 000 8 000 200SZZST 0.0.9 0.0.8 9.0.54.64.025 8.28 4 060 92 2 60 5 24 000 0 000 000 20SST 2.0.424 2.0.2598 0.0.9.64.025 252.9 5 50 240 00 69 22 000 28 000 5 000 20SZZST 2.0.424 2.0.2598 0.0.9.64.025 252.9 5 50 240 00 69 22 000 28 000 5 000 202SST 5.0.5906 5.0.80.0.4.64.025 0.45 6 240 400 250 84 9 000 24 000 000 202SFFST 5.0.5906 5.0.80.0.4.64.025 0.45 6 240 400 250 84 9 000 24 000 000 202SZZST 5.0.5906 5.0.80.0.4.64.025 0.45 6 240 400 250 84 9 000 24 000 000 20SFFST.0.669 40.0.548 2.0.424.64.025 6.56 650 20 4 50 00 000 20 000 2 000 20SZZST.0.669 40.0.548 2.0.424.64.025 6.56 650 20 4 50 00 000 20 000 2 000 204SST 20.0.84 4.0.8504 4.0.552.00.040 50.8 0 200 2 280 6 550 40 5 000 8 000 0 000 204SZZST 20.0.84 4.0.8504 4.0.552.00.040 50.8 0 200 2 280 6 550 40 5 000 8 000 0 000 205SFFST 25.0.984 52.0 2.042 5.0.5906.00.040 568.88 200 2 520 800 50 2 000 5 000 8 500 205SZZST 25.0.984 52.0 2.042 5.0.5906.00.040 568.88 200 2 520 800 50 2 000 5 000 8 500 206SST 0.0.8 62.0 2.4409 6.0.69.00.040 89.2 5 600 50 200 2 520 0 000 000 500 206SFFST 0.0.8 62.0 2.4409 6.0.69.00.040 89.2 5 600 50 200 2 520 0 000 000 500 206SZZST 0.0.8 62.0 2.4409 6.0.69.00.040 89.2 5 600 50 200 2 520 0 000 000 500 20SZZST 5.0.80 2.0 2.846.0.669.00.040.2 20 500 4 60 5 00 440 9 000 000 6 00 04SZZST 20.0.84 52.0 2.042 5.0.5906.00.040 62.98 2 00 2 860 800 50 000 6 000 9 500 05SZZST 25.0.984 62.0 2.4409.0.669.00.040 864.4 000 80 0 800 2 40 000 4 000 500 ) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear. 2) Listed values are for a pressed stainless steel cage; ABEC.. The speed ratings have been determined through historical application and practice. ) Rating for one million revolutions or 500 hours at RPM. 8

Marathon Series Tolerances and Dimensional Data Insert Bearing Bore Tolerance and Radial Clearance BEARING BORE DIAMETER INCH MILLIMETER 4 6 8 5 6 8 4 6 20 25 0 5 40 BORE TOLERANCE -.0000 in mm +.000 +.08 +.000 +.08 +.0008 +.020 +.0008 +.020 +.0008 +.020 +.0008 +.020 +.0008 +.020 +.0008 +.020 +.0008 +.020 +.000 +.08 +.000 +.08 +.0008 +.020 +.0008 +.020 +.0008 +.020 RADIAL CLEARANCE in mm.0005.00.0.028.0006.00.05.0.000-.004.08-.06.0005.00.0.028.0006.00.05.0 Shaft meter Tolerances SHAFT DIAMETER in TOLERANCE in Up to 5 6 +0.0000 / -0.0005 2-4 +0.0000 / -0.000 For stainless steel insert bearings (RRH series), the above tolerances are especially critical because of the bearing material properties. Undersized shafting, excessive set screw tightening, and severe environmental conditions can result in excessive ring distortion which can effect the performance of the bearing. Therefore, it is highly recommended that the proper set screw torque and shaft diameter tolerance be used (see assembly instructions on pages 8 and 9). End Cover Stickout (S) SHAFT DIAMETER d in mm 20 4 25 6 0 4 5 8 6 2 40 S in mm 0.09 20.5 0.09 20.5 0.09 20.5 0.84 22.2 0.965 24.5 0.965 24.5 0.965 24.5.024 26.0 End cover available on pillow blocks (CPB), 2-bolt flange units (C2F) and 4-bolt flange units (C4F). End Cover Part number = EC prefix followed by shaft diameter. Ex.: for a -/8" shaft, EC-/8 is the endcover part number. End covers only available on composite pillow block, 2-bolt and 4-bolt flange housings. Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings 9

Assembly Instructions for MRC Marathon bearing units Step Remove any burrs on the shaft with emery cloth or a fine file. Wipe the shaft with a clean piece of cloth. Check the shaft diameter to ensure it meets the tolerances shown below. Step 2 Back out all the set screws to clear the shaft and slide the unit into position on the shaft. Step Shaft meter in Tolerance in Up to 5 6 +0.0000 / -0.0005 2-4 +0.0000 / -0.000 Make sure the housing base and mating surfaces are clean and free of any debris or burrs. Ensure that the supporting surface is flat. If the housing requires shims for adjustment, the shims MUST extend the full length and width of the base. Bolt the housing securely to the support. (See table A for maximum recommended tightening torques for composite housings.) Note: For composite pillow block and flanged housings, a thick, flat stainless steel washer should always be installed between the bolt head and mounting base to properly distribute the clamping force. Step 4 ZMaRC Inserts Before the set screws are tightened, reinspect the position to make sure the housing did not shift when the base bolts were tightened. Tighten each set screw alternately with the proper hex head socket wrench until they stop turning and the hex head socket wrench starts to spring. Reference Table B for maximum recommended set screw tightening torque values and wrench dimensions. These values should not be exceeded. Step 4 Stainless Steel Inserts Before the set screws are tightened, reinspect the position to make sure the housing did not shift when the base bolts were tightened. Remove the set screws and apply a bonding agent to the set screw s threads such as LocTite and insert the set screws back into the inner ring. Tighten each set screw alternately with the proper hex head socket wrench until they stop turning and the hex head socket wrench starts to spring. Reference Table B for maximum recommended set screw tightening torque values and wrench dimensions. These values should not be exceeded. Step Step 2 Step Step 4 40

TABLE A Composite Housings Maximum Bolt Tightening Torques PILLOW BLOCK 2- AND 4-BOLT FLANGE TAPPED BASE MAX MAX BOLT SIZE MAX SHAFT BOLT DIAMETER TIGHTENING BOLT DIAMETER TIGHTENING SIZE TORQUE TORQUE UNC THREAD TIGHTENING TORQUE IN. MM IN. - LBS. IN. MM IN. - LBS. IN. IN. - LBS. 4" 8 0.0 90 8 0.0 40 8-6 0 " 8 0.0 40 8 0.0 40 8-6 0 8" 2. 40 8 0.0 40 6-4 50 6" 2. 40 8 0.0 40 6-4 50 4R" 2. 40 8 0.0 40 6-4 50 4" 2. 45 2. 40-0 6" 2. 45 2. 40-0 " 2. 520 2. 520-0 5 6" 5 8 5.9 560 5 8 5.9 520 5 8-200 20 mm 8 0.0 90 8 0.0 40 8-6 0 25 mm 8 0.0 40 8 0.0 40 8-6 0 0 mm 2. 40 8 0.0 40 6-4 50 5 mm 2. 45 2. 40-0 40 mm 2. 520 2. 520-0 TABLE B ZMaRC Insert Bearing Set Screw Specifications (RRZ-BRR) SHAFT SIZE SET HEX MAX. SCREW WRENCH TIGHTENING SIZE SIZE TORQUE IN. - LBS. 4" 4"-28 x 4" 8" 8 " 4"-28 x 4" 8" 8 8" 4"-28 x 4" 8" 8 6" 4"-28 x 4" 8" 8 4R" 4"-28 x 4" 8" 8 4" 5 6"-24 x 5 6" 5 " 65 6" 5 6"-24 x 5 6" 5 " 65 " 5 6"-24 x 5 6" 5 " 65 5 6" 8"-24 x 8" 6" 0 20 mm M6 x 0.5mm x 5mm mm 8 25 mm M6 x 0.5mm x 5mm mm 8 0 mm M6 x 0.5mm x 5mm mm 8 5 mm M6 x 0.5mm x mm mm 65 40 mm M8 x mm x mm 4 mm 65 Stainless Steel Insert Bearing Set Screw Specifications (RRH-BRR) SHAFT SIZE SET HEX MAX. SCREW WRENCH TIGHTENING SIZE SIZE TORQUE IN. - LBS. /4" 4"-28 x 6" 8" 5 " 4"-28 x 6" 8" 5 -/6" 4"-28 x 6" 8" 5 -/4R" 4"-28 x 6" 8" 5 -/4" 5 6"-24 x 4" 5 " 80 -/8" 5 6"-24 x 4" 5 " 80 -/6" 5 6"-24 x 4" 5 " 80 -/2" 5 6"-24 x 4" 5 " 80 20 mm M6 x 0.5mm x 5mm mm 5 25 mm M6 x 0.5mm x 5mm mm 5 0 mm M6 x 0.5mm x 5mm mm 5 5 mm M6 x 0.5mm x mm mm 5 40 mm M8 x mm x mm 4 mm 80 Mounting the Insert Bearing into the Housing Position the bearing 90 degrees from its normal position and insert it into the slots in the housing, making sure that the set screws do not interfere with the edge of the housing bore. Then swivel the bearing into position using a piece of tubing through the bore. If the housing has a relubrication fitting, the set screw side of the bearing should be matched to the side of the housing with the insert slots. In order to ensure that the relubrication fitting and lubrication holes line up, the initial misalignment should not exceed 5 degrees. Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings 4

Marathon Mounted Unit Basic Comparison Inch Shafts Pillow Blocks SHAFT DIAMETER 4" 5 6" " 8" 6" HOUSING INSERT BEARING MRC Composite ZMaRC CPB02ZM CPB05ZM CPB00ZM CPB02ZM CPB0ZM Composite Stainless Steel CPB02SS CPB00SS CPB0SS ZMaRC Coated Cast Iron ZMaRC ZPB02ZM ZPB05ZM ZPB00ZM ZPB02ZM ZPB0ZM Cast Stainless Steel Stainless Steel SPB02SS SPB00SS SPB0SS AMI Dodge Fafnir Polymer Black Oxide UCPPL204-2MZ UCPPL205-5MZ UCPPL205-6MZ UCPPL206-8MZ UCPPL206-9MZ Polymer Stainless Steel MUCPPL204-2 MUCPPL205-5 MUCPPL205-6 MUCPPL206-8 MUCPPL206-9 Polymer TDC P2B-SCEZ-02-PCR P2B-SCEZ-05-PCR P2B-SCEZ-00-PCR P2B-SCEZ-02-PCR P2B-SCEZ-0-PCR Teflon Coated TDC P2B-SCTC-02-CR P2B-SCTC-05-CR P2B-SCTC-00-CR P2B-SCTC-02-CR P2B-SCTC-0-CR Polymer TDC YAS 4 PT YAS 5 6 PT YAS PT YAS 8 PT YAS 6 PT Nickel Plated TDC YAS 4 NT YAS 5 6 NT YAS NT YAS 8 NT YAS 6 NT Hub City Link-Belt Nickel Plated 5200 Steel PB25IN- 4 PB25IN- 5 6 PB25IN- PB25IN- 8 PB25IN- 6 Cast Iron 5200 Steel PB25I- 4 PB25I- 5 6 PB25I- PB25I- 8 PB25I- 6 Nylon Coated Black Oxide WP-S22E WP-S25E WP-S26E WP-S28E WP-SE Nickel Plated Black Oxide P-S22EK5 P-S25EK5 P-S26EK5 P-S28EK5 P-SEK5 McGill Nickel Plated Black Oxide NC-25-4 NC-25-5 6 NC-25- NC-25-8 NC-25-6 Cast Iron 5200 Steel C-25-4 C-25-5 6 C-25- C-25-8 C-25-6 Sealmaster Polymer Coated TDC BP-2 BP-5 BP-6 BP-8 BP-9 Polymer Coated Black Oxide NP-2C-CR NP-5C-CR NP-6C-CR NP-8C-CR NP-9C-CR SKF Cast Iron 5200 Steel SY 4 TR SY 5 6TR SY TR SY 8 TR SY 6 TR Two-Bolt Flange Units SHAFT DIAMETER 4" 5 6" " 8" 6" HOUSING INSERT BEARING MRC Composite ZMaRC C2F02ZM C2F05ZM C2F00ZM C2F02ZM C2F0ZM Composite Stainless Steel C2F02SS C2F00SS C2F0SS ZMaRC Coated Cast Iron ZMaRC Z2F02ZM Z2F05ZM Z2F00ZM Z2F02ZM Z2F0ZM Cast Stainless Steel Stainless Steel S2F02SS S2F00SS S2F0SS AMI Dodge Fafnir Polymer Black Oxide UCNFL204-2MZ UCNFL205-5MZ UCNFL205-6MZ UCNFL206-8MZ UCNFL206-9MZ Polymer Stainless Steel MUCNFL204-2 MUCNFL205-5 MUCNFL205-6 MUCNFL206-8 MUCNFL206-9 Polymer TDC F2B-SCEZ-02-PCR F2B-SCEZ-05-PCR F2B-SCEZ-00-PCR F2B-SCEZ-02-PCR F2B-SCEZ-0-PCR Teflon Coated TDC F2B-SCTC-02-CR F2B-SCTC-05-CR F2B-SCTC-00-CR F2B-SCTC-02-CR F2B-SCTC-0-CR Polymer TDC YCJT 4 PT YCJT 5 6 PT YCJT PT YCJT 8 PT YCJT 6 PT Nickel Plated TDC YCJT 4 NT YCJT 5 6 NT YCJT NT YCJT 8 NT YCJT 6 NT Hub City Link-Belt Nickel Plated 5200 Steel FB260N- 4 FB260N- 5 6 FB260N- FB260N- 8 FB260N- 6 Cast Iron 5200 Steel FB260-4 FB260-5 6 FB260- FB260-8 FB260-6 Polymer Black Oxide KFX-S22E KFX-S25 KFX-S26 KFX-S28 KFX-S Nylon Coated Black Oxide WFX-S22E WFX-S25E WFX-S26E WFX-S28E WFX-SE McGill Nickel Plated Black Oxide NFC2-25- 4 NFC2-25- 5 6 NFC2-25- NFC2-25- 8 NFC2-25- 6 Cast Iron 5200 Steel FC2-25- 4 FC2-25- 5 6 FC2-25- FC2-25- 8 FC2-25- 6 Sealmaster Polymer Coated TDC BFT-2 BFT-5 BFT-6 BFT-8 BFT-9 Polymer Coated Black Oxide SFT-2C-CR SFT-5C-CR SFT-6C-CR SFT-8C-CR SFT-9C-CR SKF Cast Iron 5200 Steel FYTB 4 TR FYTB 5 6 TR FYTB TR FYTB 8TR FYTB 6 TR 42

Marathon Mounted Unit Basic Comparison Inch Shafts Pillow Blocks 4" 4" 8" 6" " 5 6" MRC CPB04ZMR CPB04ZM CPB0ZM CPB08ZM CPB5ZM CPB04SSR CPB04SS CPB06SS CPB0SS CPB08SS ZPB04ZMR ZPB04ZM ZPB0ZM ZPB08ZM ZPB5ZM SPB04SSR SPB04SS SPB06SS SPB0SS SPB08SS UCPPL206-20MZ UCPPL20-20MZ UCPPL20-22MZ UCPPL20-2MZ UCPPL208-24MZ AMI MUCPPL206-20 MUCPPL20-20 MUCPPL20-22 MUCPPL20-2 MUCPPL208-24 Dodge Fafnir P2B-SCUEZ-04S-PCR P2B-SCUEZ-04-PCR P2B-SCEZ-06-PCR P2B-SCEZ-0-PCR P2B-SCBEZ-08-PCR P2B-SCBEZ-5-PCR P2B-SCTC-04S-CR P2B-SCTC-04-CR P2B-SCTC-06-CR P2B-SCTC-0-CR P2B-SCTC-08-CR P2B-SCTC-5-CR YAS 4 SPT YAS 4 PT YAS 8 PT YAS 6 PT YAS PT YAS 5 6 PT YAS 4 SNT YAS 4 NT YAS 8 NT YAS 6 NT YAS NT YAS 5 6 NT Hub City Link-Belt PB25IN- 4 S PB25IN- 4 PB25IN- 8 PB25IN- 6 PB25IN- PB25IN 5 6 PB25I- 4 S PB25I- 4 PB25I- 8 PB25I- 6 PB25I- PB25 5 6 WP-S2E20E WP-S220E WP-S222E WP-S22E WP-S224E WP-S2E P-S2E20EK5 P-S220EK5 P-S222EK5 P-S22EK5 P-S224EK5 P-S2EK5 McGill NC-25-4 S NC-25-4 NC-25-8 NC-25-6 NC-25- NC-25-5 6 C-25-4 S C-25-4 C-25-8 C-25-6 C-25- C-25-5 6 Sealmaster BP-20R BP-20 BP-22 BP-2 BP-24 BP- NP-20RC-CR NP-20C-CR NP-22C-CR NP-2C-CR NP-24C-CR NP-C-CR SKF SY 4 STR SY 4 TR SY 8 TR SY 6 TR SY TR SY 5 6 TR Two-Bolt Flange Units 4" 4" 8" 6" " 5 6" MRC C2F04ZMR C2F04ZM C2F0ZM C2F08ZM C2F5ZM C2F04SSR C2F04SS C2F06SS C2F0SS C2F08SS Z2F04ZMR Z2F04ZM Z2F0ZM Z2F08ZM Z2F5ZM S2F04SSR S2F04SS Z2F06SS S2F0SS S2F08SS UCNFL206-20MZ UCNFL20-20MZ UCNFL20-22MZ UCNFL20-2MZ UCNFL208-24MZ AMI MUCNFL206-20 MUCNFL20-20 MUCNFL20-22 MUCNFL20-2 MUCNFL208-24 Dodge Fafnir F2B-SCEZ-04S-PCR F2B-SCEZ-04-PCR F2B-SCEZ-06-PCR F2B-SCEZ-0-PCR F2B-SCEZ-08-PCR F2B-SCEZ-5-PCR F2B-SCTC-04S-CR F2B-SCTC-04-CR F2B-SCTC-06-CR F2B-SCTC-0-CR F2B-SCTC-08-CR F2B-SCTC-08-CR YCJT 4 SPT YCJT 4 PT YCJT 8 PT YCJT 6 PT YCJT PT YCJT 5 6 PT YCJT 4 SNT YCJT 4 NT YCJT 8 NT YCJT 6 NT YCJT NT YCJT 5 6 NT Hub City Link-Belt FB260N- 4 S FB260N- 4 FB260N- 8 FB260N- 6 FB260N- FB260N- 5 6 FB260-4 S FB260-4 FB260-8 FB260-6 FB260- FB260-5 6 KFX-S2E20 KFX-S220 KFX-S222 KFX-S22 KFX-S224 WFX-S2E20E WFX-S220E WFX-S222E WFX-S22E WFX-S224E WFX-S2E McGill NFC2-25- 4S NFC2-25- 4 NFC2-25- 8 NFC2-25- 6 NFC2-25- NFC2-25- 5 6 FC2-25- 4S FC2-25- 4 FC2-25- 8 FC2-25- 6 FC-25- FC-25-5 6 Sealmaster BFT-20R BFT-20 BFT-22 BFT-2 BFT-24 BFT- SFT-20RC-CR SFT-20C-CR SFT-22C-CR SFT-2C-CR SFT-24C-CR SFT-C-CR SKF FYTB 4 STR FYTB 4 TR FYTB 8 TR FYTB 6 TR FYTB TR Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings 4

Marathon Mounted Unit Basic Comparison Inch Shafts Four-Bolt Flange Units SHAFT DIAMETER 4" 5 6" " 8" 6" Housing Insert Bearing MRC Composite ZMaRC C4F02ZM C4F05ZM C4F00ZM C4F02ZM C4F0ZM Composite Stainless Steel C4F02SS Z4F05ZM C4F00SS C4F0SS ZMaRC Coated Cast Iron ZMaRC Z4F02ZM Z4F00ZM Z4F02ZM Z4F0ZM Cast Stainless Steel Stainless Steel S4F02SS S4F00SS S4F0SS AMI Polymer Black Oxide UCFPL204-2MZ UCFPL205-5MZ UCFPL205-6MZ UCFPL206-8MZ UCFPL206-9MZ Polymer Stainless Steel MUCFPL204-2 MUCFPL205-5 MUCFPL205-6 MUCFPL206-8 MUCFPL206-9 Dodge Fafnir Polymer TDC F4B-SCEZ-02-PCR F4B-SCEZ-05-PCR F4B-SCEZ-00-PCR F4B-SCEZ-02-PCR F4B-SCEZ-0-PCR Teflon Coated TDC F4B-SCTC-02-CR F4B-SCTC-05-CR F4B-SCTC-00-CR F4B-SCTC-02-CR F4B-SCTC-0-CR Polymer TDC YCJ 4 PT YCJ 5 6 PT YCJ PT YCJ 8 PT YCJ 6 PT Nickel Plated TDC YCJ 4 NT YCJ 5 6 NT YCJ NT YCJ 8 NT YCJ 6 NT Hub City Link-Belt Nickel Plated 5200 Steel FB250N- 4 FB250N- 5 6 FB250N- FB250N- 8 FB250N- 6 Cast Iron 5200 Steel FB250-4 FB250-5 6 FB250- FB250-8 FB250-6 Polymer Black Oxide KF-S22 KF-S25 KF-S26 KF-S28 KF-S Nylon Coated Black Oxide WF-S22E WF-S25E WF-S26E WF-S28E WF-SE McGill Nickel Plated Black Oxide NFC4-25- 4 NFC4-25- 5 6 NFC4-25- NFC4-25- 8 NFC4-25- 6 Cast Iron 5200 Steel FC4-25- 4 FC4-25- 5 6 FC4-25- FC4-25- 8 FC4-25- 6 Sealmaster Polymer Coated TDC BF-2 BF-5 BF-6 BF-8 BF-9 Polymer Coated Black Oxide SF-2C-CR SF-5C-CR SF-6C-CR SF-8C-CR SF-9C-CR SKF Cast Iron 5200 Steel FY 4 TR FY 5 6 TR FY TR FY 8 TR FY 6 TR Tapped-Base Pillow Blocks SHAFT DIAMETER 4" 5 6" " 8" 6" HOUSING INSERT BEARING MRC AMI Dodge Composite ZMaRC CTB02ZM CTB05ZM CTB00ZM CTB02ZM CTB0ZM Composite Stainless Steel CTB02SS CTB00SS CTB0SS ZMaRC Coated Cast Iron ZMaRC ZTB02ZM ZTB05ZM ZTB00ZM ZTB02ZM ZTB0ZM Cast Stainless Steel Stainless Steel STB02SS STB00SS STB0SS Polymer Black Oxide UCTBL204-2MZ UCTBL205-5MZ UCTBL205-6MZ UCTBL206-8MZ UCTBL206-9MZ Polymer Stainless Steel MUCTBL204-2 MUCTBL205-5 MUCTBL205-6 MUCTBL206-8 MUCTBL206-9 Polymer TDC TB-SCEZ-02-PCR TB-SCEZ-05-PCR TB-SCEZ-00-PCR TB-SCEZ-02-PCR TB-SCEZ-0-PCR Cast Iron 5200 Steel TB-SC-02 TB-SC-05 TB-SC-00 TB-SC-02 TB-SC-0 Fafnir Cast Iron 5200 Steel STB 4 STB 5 6 STB STB 8 STB 6 Hub City Cast Iron 5200 Steel TBP250-4 TBP250-5 6 TBP250- TBP250-8 TBP250-6 Link Belt Nickel Plated Black Oxide PT-S22EK5 PT-S25EK5 PT-S26EK5 PT-S28EK5 PT-SEK5 Nylon Coated Black Oxide WPT-S22E WPT-S25E WPT-S26E WPT-S28E WPT-SE McGill Cast Iron 5200 Steel TBC-25-4 TBC-25-5 6 TBC-25- TBC-25-8 TBC-25-6 Sealmaster Polymer Coated TDC BTB-2 BTB-5 BTB-6 BTB-8 BTB-9 Cast Iron 5200 Steel TB-2 TB-5 TB-6 TB-8 TB-9 44

Marathon Mounted Unit Basic Comparison Inch Shafts Four-Bolt Flange Units 4" 4" 8" 6" " 5 6" MRC C4F04ZMR C4F04ZM C4F0ZM C4F08ZM C4F5ZM C4F04SSR C4F04SS C4F06SS C4F0SS C4F08SS Z4F04ZMR Z4F04ZM Z4F0ZM Z4F08ZM Z4F5ZM S4F04SSR S4F04SS S4F06SS S4F0SS S4F08SS UCFPL206-20MZ UCFPL20-20MZ UCFPL20-22MZ UCFPL20-2MZ UCFPL208-24MZ AMI MUCFPL206-20 MUCFPL20-20 MUCFPL20-22 MUCFPL20-2 MUCFPL208-24 Dodge Fafnir F4B-SCEZ-04S-PCR F4B-SCEZ-04-PCR F4B-SCEZ-0-PCR F4B-SCEZ-08-PCR F4B-SCEZ-5-PCR F4B-SCEZ-04S-CR F4B-SCEZ-04-CR F4B-SCEZ-0-CR F4B-SCEZ-08-CR F4B-SCEZ-5-CR YCJ 4 SPT YCJ 4 PT YCJ 8 PT YCJ 6 PT YCJ PT YCJ 5 6 PT YCJ 4 SNT YCJ 4 NT YCJ 8 NT YCJ 6 NT YCJ NT YCJ 5 6 NT Hub City Link-Belt FB250N- 4 S FB250N- 4 FB250N- 8 FB250N- 6 FB250N- FB250-4 S FB250-4 FB250-8 FB250-6 FB250- KF-S2E20 KF-S220 KF-S222 KF-S22 KF-S224 WF-S2E20E WF-S220E WF-S222E WF-S22E WF-S224E WF-S2E McGill NFC4-25- 4S NFC4-25- 4 NFC4-25- 8 NFC4-25- 6 NFC4-25- NFC4-25- 5 6 FC4-25- 4S FC4-25- 4 FC4-25- 8 FC4-25- 6 FC4-25- FC4-25- 5 6 Sealmaster BF-20R BF-20 BF-22 BF-2 BF-24 BF- SF-20RC-CR SF-20C-CR SF-22C-CR SF-2C-CR SF-24C-CR SF-C-CR SKF FY 4 STR FY 4 TR FY 8 TR FY 6 TR FY TR FY 5 6 TR Tapped-Base Pillow Blocks 4" 4 " 8" 6" " 5 6" MRC AMI Dodge CTB04ZMR CTB04ZM CTB0ZM CTB08ZM CTB5ZM CTB04SSR CTB04SS CTB06SS CTB0SS CTB08SS ZTB04ZMR ZTB04ZM ZTB0ZM ZTB08ZM ZTB5ZM STB04SSR STB04SS STB06SS STB0SS STB08SS UCTBL206-20MZ UCTBL20-20MZ UCTBL20-22MZ UCTBL20-2MZ UCTBL20-24MZ MUCTBL206-20 MUCTBL20-20 MUCTBL20-22 MUCTBL20-2 MUCTBL20-24 TB-SCEZ-04S-PCR TB-SCEZ-04-PCR TB-SCEZ-06-PCR TB-SCEZ-0-PCR TB-SCEZ-08-PCR TB-SC-04S TB-SC-04 TB-SC-06 TB-SC-0 TB-SC-08 TB-SC-5 Fafnir STB 4S STB 4 STB 8 STB 6 STB Hub City TBP250-4S TBP250-4 TBP250-8 TBP250-6 TBP250- TBP250-5 6 PT-S2E20EK5 PT-S220EK5 PT-S222EK5 PT-S22EK5 PT-S224EK5 PT-S2EK5 Link Belt WPT-S2E20E WPT-S220E WPT-S222E WPT-S22E PT-S224E WPT-S2E McGill TBC-25-4S TBC-25-4 TBC-25-8 TBC-25-6 TBC-25- TBC-25-5 6 BTB-20R BTB-20 BTB-22 BTB-2 BTB-24 BTB- Sealmaster TB-20R TB-20 TB-22 TB-2 TB-24 TB- Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings 45

Marathon Mounted Unit Basic Comparison Inch Shafts -Bolt Bracket Flange Units SHAFT DIAMETER 4" 5 6" " 8" 6" HOUSING INSERT BEARING MRC Composite ZMaRC CBF02ZM CBF05ZM CBF00ZM CBF02ZM CBF0ZM Composite Stainless Steel CBF02SS CBF00SS CBF00SS Polymer Black Oxide UCFBL204-2MZ UCFBL205-5MZ UCFBL205-6MZ AMI Polymer Stainless Steel MUCFBL204-2 MUCFBL205-5 MUCFBL205-6 Polymer TDC FB-SCEZ-02-CR FB-SCEZ-05-CR FB-SCEZ-00-CR FB-SCEZ-02-CR Dodge Nylon Coated TDC FB-SCEZ-02-NY FB-SCEZ-05-NY FB-SCEZ-00-NY FB-SCEZ-02-NY FB-SCEZ-0-NY Nickel Plated Black Oxide FB-S22EK5 FB-25EK5 FB-S26EK5 FB-S28EK5 FB-SEK5 Link Belt Nylon Coated Black Oxide WFB-S22E WFB-S25E WFB-S26E WFB-S28E WFB-SE McGill Sealmaster Nickel Plated Black Oxide NMFB- 4 NMFB- 5 6 NMFB- NMFB- 8 NMFB- 6 Cast Iron 5200 Steel MFB- 4 MFB- 5 6 MFB- MFB- 8 MFB- 6 Polymer Coated TDC BFB-2 BFB-5 BFB-6 BFB-8 BFB-9 Polymer Coated Black Oxide FB-2C-CR FB-5C-CR FB-6C-CR FB-8C-CR FB-9C-CR Narrow-Slot Take-Up Units SHAFT DIAMETER 4" 5 6" " 8" 6" HOUSING INSERT BEARING MRC Composite ZMaRC CTN02ZM CTN05ZM CTN00ZM CTN02ZM CTN0ZM Composite Stainless Steel CTN02SS CTN00SS CTN0SS Polymer TDC NSTU-SCEZ-02-PCR NSTU-SCEZ-05-PCR NSTU-SCEZ-00-PCR NSTU-SCEZ-02-PCR NSTU-SCEZ-0-PCR Dodge Nickel Plated 5200 Steel NSTU-SCNP-02 NSTU-SCNP-05 NSTU-SCNP-00 NSTU-SCNP-02 NSTU-SCNP-0 Hub City Nickel Plated 5200 Steel TU250N- 4 TU250N- 5 6 TU250N- TU250N- 8 TU250N- 6 Cast Iron 5200 Steel TU250-4 TU250-5 6 TU250- TU250-8 TU250-6 Wide Slot Take-up Frames SHAFT DIAMETER 4" 5 6" " 8" 6" HOUSING INSERT BEARING MRC Composite ZMaRC CTW02ZM CTW05ZM CTW00ZM CTW02ZM CTW0ZM Composite Stainless Steel CTW02SS CTW00SS CTW0SS Polymer Black Oxide UCTPL204-2MZ UCTPL205-5MZ UCTPL205-6MZ UCTPL206-8MZ UCTPL206-9MZ AMI Polymer Stainless Steel MUCTPL204-2 MUCTPL205-5 MUCTPL205-6 MUCTPL206-8 MUCTPL206-9 Polymer TDC WSTU-SCEZ-02-PCR WSTU-SCEZ-05-PCR WSTU-SCEZ-00-PCR WSTU-SCEZ-02-CR WSTU-SCEZ-0-PCR Dodge Nickel Plated 5200 Steel WSTU-SCNP-02 WSTU-SCNP-05 WSTU-SCNP-00 WSTU-SCNP-02 WSTU-SCNP-0 Hub City Ductile Iron 5200 Steel WSTU- 4 WSTU- 5 6 WSTU- WSTU- 8 WSTU- 6 Nickel Plated Black Oxide TH-S22EK5 TH-S25EK5 TH-S26EK5 TH-S28EK5 TH-SEK5 Link Belt Nylon Coated Black Oxide WTH-S22E WTH-S25E WTH-S26E WTH-S28E WTH-SE McGill Nickel Plated Black Oxide NTC-25-4 NTC-25-5 6 NTC-25- NTC-25-8 NTC-25-6 Polymer TDC BST-2 BST-5 BST-6 BST-8 BST-9 Sealmaster Polymer Black Oxide ST-2 ST-5 ST-6 ST-8 ST-9 SKF Cast Iron 5200 Steel TU 4 TR TU 5 6 TR TUTR TU 8 TR TU 6TR 46

Marathon Mounted Unit Basic Comparison Inch Shafts -Bolt Bracket Flange Units 4" 4 " 8" 6" " 5 6" MRC CBF04ZMR CBF04ZM CBF0ZM CBF08ZM CBF5ZM CBF04SSR CBF04SS CBF06SS CBF0SS CBF08SS AMI Dodge Link Belt McGill Sealmaster FB-SCEZ-045-CR FB-SCEZ-04-CR FB-SCEZ-06-CR FB-SCEZ-0-CR FB-SCEZ-045-NY FB-S2E20EK5 FB-S220EK5 FB-S222EK5 FB-S22EK5 WFB-S2E20E WFB-S220E WFB-S222E WFB-S22E NMFB- 4S NMFB- 4 NMFB- 8 NMFB- 6 NMFB- 5 6 MFB- 4S MFB- 4 MFB- 8 MFB- 6 MFB- 5 6 BFB-20R BFB-20 BFB-22 BFB-2 BFB-24 BFB- FB-20RC-CR FB-20C-CR FB-22C-CR FB-2C-CR FB-24C-CR FB-C-CR Narrow-Slot Take-Up Units 4" 4 " 8" 6" " 5 6" MRC CTN04ZMR CTN04ZM CTN0ZM CTN08ZM CTN5ZM CTN04SSR CTN04SS CTN06SS CTN0SS CTN08SS Dodge NSTU-SCEZ-04S-PCR NSTU-SCEZ-04-PCR NSTU-SCEZ-06-PCR NSTU-SCEZ-0-PCR NSTU-SCEZ-08-PCR NSTU-SCEZ-5-PCR NSTU-SCNP-045 NSTU-SCNP-04 NSTU-SCNP-06 NSTU-SCNP-0 NSTU-SCNP-08 NSTU-SCNP-5 Hub City TU250N- 4S TU250N- 4 TU250N- 8 TU250N- 6 TU250N- TU250N- 5 6 TU250-4S TU250-4 TU250-8 TU250-6 TU250- TU250-5 6 Wide Slot Take-up Frames 4" 4 " 8" 6" " 5 6" MRC CTW04ZMR CTW04ZM CTW0ZM CTW08ZM CTW5ZM CTW04SSR CTW04SS CTW06SS CTW0SS CTW08SS AMI Dodge UCTPL206-20MZ UCTPL20-20MZ UCTPL20-22MZ UCTPL20-2MZ UCTPL208-24MZ MUCTPL206-20 MUCTPL20-20 MUCTPL20-22 MUCTPL20-2 MUCTPL208-24 WSTU-SCEZ-04S-PCR WSTU-SCEZ-04-PCR WSTU-SCEZ-06-PCR WSTU-SCEZ-0-PCR WSTU-SCEZ-08-PCR WSTU-SCEZ-5-PCR WSTU-SCNP-04S WSTU-SCNP-04 WSTU-SCNP-06 WSTU-SCNP-0 WSTU-SCNP-08 WSTU-SCNP-5 Hub City WSTU- 4S WSTU- 4 WSTU- 8 WSTU- 6 WSTU- WSTU- 5 6 Link Belt TH-S2E20EK5 TH-S220EK5 TH-S222EK5 TH-S22EK5 TH-S224EK5 TH-S2E WTH-S2E20E WTH-S220E WTH-S222E WTH-S22E WTH-S224E WTH-S2E McGill NTC-25-4S NTC-25-4 NTC-25-8 NTC-25-6 NTC-25- NTC-25-5 6 Sealmaster BST-20R BST-20 BST-22 BST-2 BST-24 BST- ST-20R ST-20 ST-22 ST-2 ST-24 ST- SKF TU 4 STR TU 4 TR TU 8 TR TU 6 TR TU TR TU 5 6 TR Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings 4

Marathon Mounted Unit Basic Comparison Metric Shafts Pillow Blocks SHAFT DIAMETER 20mm 25mm 0mm 5mm 40mm HOUSING INSERT BEARING MRC Composite ZMaRC CPB20ZM CPB25ZM CPB0ZM CPB5ZM CPB40ZM Composite Stainless Steel CPB20SS CPB25SS CPB0SS CPB5SS CPB40SS ZMaRC Coated Cast Iron ZMaRC ZPB20ZM ZPB25ZM ZPB0ZM ZPB5ZM ZPB40ZM Cast Stainless Steel Stainless Steel SPB20SS SPB25SS SPB0SS SPB5SS SPB40SS AMI Polymer Black Oxide UCPPL-204MZ UCPPL-205MZ UCPPL-206MZ UCPPL-20MZ UCPPL-208MZ Polymer Stainless Steel MUCPPL-204 MUCPPL-205 MUCPPL-206 MUCPPL-20 MUCPPL-208 Dodge Polymer TDC P2B-SCEZ-20M-WCR P2B-SCEZ-25M-WCR P2B-SCEZ-0M-WCR P2B-SCEZ-5M-WCR P2B-SCEZ-40M-WCR Cast Iron 5200 Steel P2B-SC-20M P2B-SC-25M P2B-SC-0M P2B-SC-5M P2B-SC-40M Fafnir Cast Iron 5200 Steel YAS20 YAS25 YAS0 YAS5 YAS40 Polymer TDC YAS20PT YAS25PT YAS0PT YAS5PT YAS40PT Link-Belt Nickel Plated Black Oxide P-U2M20NK5 P-U2M25NK5 P-U2M0NK5 P-U2M5NK5 P-U2M40NK5 Cast Iron 5200 Steel P-U2M20N P-U2M25N P-U2M0N P-U2M5N P-U2M40N McGill Nickel Plated Black Oxide NC-25-20 NC-25-25 NC-25-0 NC-25-5 NC-25-40 Cast Iron 5200 Steel C-25-20 C-25-25 C-25-0 C-25-5 C-25-40 Sealmaster Nickel Plated Black Oxide NP-204NK NP-205NK NP-206NK NP-20NK NP-208NK Cast Iron 5200 Steel NP-204 NP-205 NP-206 NP-20 NP-208 SKF Cast Iron 5200 Steel SY20TR SY25TR SY0TR SY5TR SY40TR Two-Bolt Flange Units SHAFT DIAMETER 20mm 25mm 0mm 5mm 40mm HOUSING INSERT BEARING MRC Composite ZMaRC C2F20ZM C2F25ZM C2F0ZM C2F5ZM C2F40ZM Composite Stainless Steel C2F20SS C2F25SS C2F0SS C2F5SS C2F40SS ZMaRC Coated Cast Iron ZMaRC Z2F20ZM Z2F25ZM Z2F0ZM Z2F5ZM Z2F40ZM Cast Stainless Steel Stainless Steel S2F20SS S2F25SS S2F0SS S2F5SS S2F40SS AMI Polymer Black Oxide UCNFL-204MZ UCNFL-205MZ UCNFL-206MZ UCNFL-20MZ UCNFL-208MZ Polymer Stainless Steel MUCNFL-204 MUCNFL-205 MUCNFL-206 MUCNFL-20 MUCNFL-208 Dodge Polymer TDC F2B-SCEZ-20M-WCR F2B-SCEZ-25M-WCR F2B-SCEZ-0M-WCR F2B-SCEZ-5M-WCR F2B-SCEZ-40M-WCR Cast Iron 5200 Steel F2B-SC-20M F2B-SC-25M F2B-SC-0M F2B-SC-5M F2B-SC-40M Fafnir Polymer TDC YCJT20PT YCJT25PT YCJT0PT YCJT5PT Cast Iron 5200 Steel YCJT20 YCJT25 YCJT0 YCJT5 YCJT40 Link-Belt Polymer Black Oxide KFX-2M20E KFX-2M25E KFX-2M0E Nylon Coated Black Oxide KLFX-2M20E KLFX-2M25E KLFX-2M0E McGill Nickel Plated Black Oxide NFC2-25-20 NFC2-25-25 NFC2-25-0 NFC2-25-5 NFC2-25-40 Cast Iron 5200 Steel FC2-25-20 FC2-25-25 FC2-25-0 FC2-25-5 FC2-25-40 Nickel Plated Black Oxide SFT-204NK SFT-205NK SFT-206NK SFT-20NK SFT-208NK Sealmaster Cast Iron 5200 Steel SFT-204 SFT-205 SFT-206 SFT-20 SFT-208 SKF Cast Iron 5200 Steel FYBT20TR FYBT25TR FYBT0TR FYBT5TR FYBT40TR Four-Bolt Flange Units SHAFT DIAMETER 20mm 25mm 0mm 5mm 40mm HOUSING INSERT BEARING MRC Composite ZMaRC C4F20ZM C4F25ZM C4F0ZM C4F5ZM C4F40ZM Composite Stainless Steel C4F20SS C4F25SS C4F0SS C4F5SS C4F40SS ZMaRC Coated Cast Iron ZMaRC Z4F20ZM Z4F25ZM Z4F0ZM Z4F5ZM Z4F40ZM Cast Stainless Steel Stainless Steel S4F20SS S4F25SS S4F0SS S4F5SS S4F40SS AMI Polymer Black Oxide UCFPL-204MZ UCFPL-205MZ UCFPL-206MZ UCFPL-20MZ UCFPL-208MZ Polymer Stainless Steel MUCFPL-204 MUCFPL-205 MUCFPL-206 MUCFPL-20 MUCFPL-208 Dodge Polymer TDC F4B-SCEZ-20M-WCR F4B-SCEZ-25M-WCR F4B-SCEZ-0M-WCR F4B-SCEZ-5M-WCR F4B-SCEZ-40M-WCR Cast Iron 5200 Steel F4B-SC-20M F4B-SC-25M F4B-SC-0M F4B-SC-5M F4B-SC-40M Fafnir Polymer TDC YCJ20PT YCJ25PT YCJ0PT YCJ5PT YCJ40PT Cast Iron 5200 Steel YCJ20 YCJ25 YCJ0 YCJ5 YCJ40 Link-Belt Polymer Black Oxide KF-2M25E KF-2M0E KF-2M5E KF-2M40E Teflon Coated Black Oxide KLF-2M25E KLF-2M0E KLF-2M5E KLF-2M40E McGill Nickel Plated Black Oxide NFC4-25-20 NFC4-25-25 NFC4-25-0 NFC4-25-5 NFC4-25-40 Cast Iron 5200 Steel FC4-25-20 FC4-25-25 FC4-25-0 FC4-25-5 FC4-25-40 Nickel Plated Black Oxide SF-204NK SF-205NK SF-206NK SF-20NK SF-208NK Sealmaster Cast Iron 5200 Steel SF-204 SF-205 SF-206 SF-20 SF-208 SKF Cast Iron 5200 Steel FY20TR FY25TR FY0TR FY5TR FY40TR 48

Marathon Mounted Unit Basic Comparison Metric Shafts Tapped-Base Pillow Blocks MRC AMI SHAFT DIAMETER 20mm 25mm 0mm 5mm 40mm HOUSING INSERT BEARING Composite ZMaRC CTB20ZM CTB25ZM CTB0ZM CTB5ZM CTB40ZM Composite Stainless Steel CTB20SS CTB25SS CTB0SS CTB5SS CTB40SS ZMaRC Coated Cast Iron ZMaRC ZTB20ZM ZTB25ZM ZTB0ZM ZTB5ZM ZTB40ZM Cast Stainless Steel Stainless Steel STB20SS STB25SS STB0SS STB5SS STB40SS Polymer Black Oxide UCTBL-204MZ UCTBL-205MZ UCTBL-206MZ UCTBL-20MZ UCTBL-208MZ Polymer Stainless Steel MUCTBL-204 MUCTBL-205 MUCTBL-206 MUCTBL-20 MUCTBL-208 Fafnir McGill Sealmaster Cast Iron 5200 Steel STB20 STB25 STB0 STB5 STB40 Cast Iron 5200 Steel TBC-25-20 TBC-25-25 TBC-25-0 TBC-25-5 TBC-25-40 Cast Iron 5200 Steel TB-204 TB-205 TB-206 TB-20 TB-208 -Bolt Bracket Flange Units SHAFT DIAMETER 20mm 25mm 0mm 5mm 40mm HOUSING INSERT BEARING MRC Composite ZMaRC CBF20ZM CBF25ZM CBF0ZM CBF5ZM CBF40ZM Composite Stainless Steel CBF20SS CBF25SS CBF0SS CBF5SS CBF40SS AMI Cast Iron 5200 Steel UCFK-204 UCFK-205 UCFK-206 UCFK-20 UCFK-208 McGill Sealmaster Nickel Plated Black Oxide NMFB-20 NMFB-25 NMFB-0 NMFB-5 NMFB-40 Cast Iron 5200 Steel FB-204 FB-205 FB-206 FB-20 FB-208 Narrow-Slot Take-Up Units SHAFT DIAMETER 20mm 25mm 0mm 5mm 40mm HOUSING INSERT BEARING MRC Composite ZMaRC CTN20ZM CTN25ZM CTN0ZM CTN5ZM CTN40ZM Composite Stainless Steel CTN20SS CTN25SS CTN0SS CTN5SS CTN40SS Nickel Plated 5200 Steel NSTUSC20MNP NSTUSC25MNP NSTUSC0MNP NSTUSC5MNP NSTUSC40MNP Dodge Cast Iron 5200 Steel NSTUSC20M NSTUSC25M NSTUSC0M NSTUSC5M NSTUSC40M Wide-Slot Take-Up Units SHAFT DIAMETER 20mm 25mm 0mm 5mm 40mm HOUSING INSERT BEARING MRC Composite ZMaRC CTW20ZM CTW25ZM CTW0ZM CTW5ZM CTW40ZM Composite Stainless Steel CTW20SS CTW25SS CTW0SS CTW5SS CTW40SS Polymer Black Oxide UCTPL-204MZ UCTPL-205MZ UCTPL-206MZ UCTPL-20MZ UCTPL-208MZ AMI Polymer Stainless Steel MUCTPL-204 MUCTPL-205 MUCTPL-206 MUCTPL-20 MUCTPL-208 Dodge Sealmaster SKF Cast Iron 5200 Steel WSTU-SC-20M WSTU-SC-25M WSTU-SC0M WSTU-SC-5M WSTU-SC-40M Polymer Black Oxide ST-204 ST-205 ST-206 ST-20 ST-208 Cast Iron 5200 Steel TU20TR TU25TR TU0TR TU5TR TU40TR Visit www.mrcbearingservices.com to download CAD drawings of MRC bearings 49

MRC Bearing Services MRC Bearing Services 50 Gehman Road Kulpsville, PA 944 USA Call Toll Free (800) MRC-000 (25) 5-4400 Toll Free Fax: -888-22-462 www.mrcbearingservices.com MRC is a registered trademark of SKF USA Inc. Marathon and ZMaRC are registered trademarks of SKF USA Inc. Although care has been taken to assure the accuracy of the data compiled in this publication, SKF does not assume any liability for errors or omissions 200 SKF USA Inc. Publication M660-0 (0M/AN 5-200) Version 5/200 Printed in USA