GRUNDFOS DATA BOOKLET ydro 0 G - X Grundfos ydro 0 G - X booster sets with 1-4 CR ums z
Contents Product data Performance range Page 3 ydro 0 G - X Page 4 Tye key Page 4 Oerating conditions Page 4 Other versions on request Page 4 Function Page 4 Grundfos Control 0 Page 5 Comonents and materials Page 5 Pum Page 6 Shaft seal Page 6 Motor Page 6 Materials CR 3, 5, 10, 15 and Page 7 Materials CR 32, 45, 64 and 90 Page 7 Materials CRI, CRN Page 7 Dimensions and weights Page 7 Construction Page 7 Installation Page 7 Performance curves/ Technical data/ Electrical data CR 3 Page 8 CR 5 Page 10 CR 10 Page 12 CR 15 Page 14 CR Page 16 CR 32 Page 18 CR 45 Page CR 64 Page 22 CR 90 Page 24 Dimensions and weights Booster set with 1 um Page 26 Booster set with 2 ums Page 28 Booster set with 3 ums Page Booster set with 4 ums Page 32 Diahragm tank Diahragm tank selection Page 34 Further roduct documentation WinCAPS Page 35 WebCAPS Page 36 2
Product data ydro 0 G - X Performance range 110 ydro 0 z 90 CR 5 CR 15 CR 32 CR 64 CR 3 CR 10 CR CR 45 CR 90 2 3 4 6 8 10 0 0 0 0 Note: detailed erformance curves on ages 8 to 24. Q [m³/h] TM02 7782 03 3
Product data ydro 0 G - X ydro 0 G - X Grundfos ydro 0 G - X booster sets consist of 2 to 4 identical Grundfos CR ums mounted in arallel on a common base frame and a control cabinet with motor rotection and integrated CS 0 controller. Pums are automatically oerated according to system demand by means of ressure switches (one for each um). The setting of the ressure switches have to be within the otimal erformance area of each um model. ydro 0 G - X booster sets are sulied as comlete, reassembled and tested systems including suction and discharge manifolds, isolating valves, non-return valves, ressure gauge and ressure switches. A ydro 0 G - X booster set with one um is also available. The booster set is assembled with main mechanical comonents. owever, the control cabinet is simler and does not incororate the CS 0. To ensure stable oeration the booster set must be fitted with a suitable diahragm tank. The size of the diahragm tank can be calculated according to the section "Diahragm tank selection" at age 34. Fig. 1 And/or PUMP PRESSURE SWITC NON-RETURN VALVE PRESSURE GAUGE ydro 0 ressure boosting system CS 0 Booster sets without suction manifolds (NOS version) are without these comonents. Non-return valves can be fitted on the discharge side on request. ydro 0 ISOLATING VALVE TM00 9718 22 Tye key Tye Examle ydro 0 G CS 3 CR 3-5 3 x 0 V G: galvanized manifolds X: stainless steel manifolds On-off control Number of ums Pum tye Voltage/frequency Oerating conditions Flow: u to 4 m 3 /h Oerating ressure: Liquid temerature: Ambient temerature: max. 10 bar +5 C to + C 0 C to + C. Maximum suction lift (): The maximum suction lift () can be calculated as follows: = 10.3 - NPS of the um - other suction losses - a safety margin of 0.5 metres. Maximum inlet ressure: Power range: DOL starting: SD starting: Power suly: 6.0 bar u to kw u to 7.5 kw 11 to kw Other versions on request 3 x 0 V, z, N, PE. The following executions are available on request: booster set with jokey um booster set without suction manifold (NOS version) booster set with CRI, 3, 5, 10, 15, ums all comonents in contact with water are in high grade stainless steel (N-version) erformance exceeding the standard range characteristics other than stated above single-hase ower suly: 1 x 2 V, z N, PE three-hase ower suly: 3 x 2 V, z N, PE starting configuration other than standard z. Function When a ta is oened, water is taken from the diahragm tank. Then the ressure dros to the first cutin ressure, and the first um is cut in. As the consumtion rises, more ums will be cut in until the erformance of the ums in oeration corresonds to the requirement. 4
Product data ydro 0 G - X When the water consumtion falls, the discarge ressure rises to the cut-out ressure and the CS 0 cuts out one um. As the consumtion falls, more ums will be cut-out. Examle: ydro 0 CS 3 Cut-in Cut-out Pr1 Pr2 Pr3 Pr1 Pr2 Pr3 One um in oeration Fig. 2 Oeration with cut-in and cut-out Grundfos Control 0 The Grundfos Control 0 suervises a given number of mains-oerated ums. The Control 0 offers the following functions, rovided by the CS 0 controller in case of two ums and above: Automatic cascade control of ums Automatic um changeover at any start-u cycle Manual oeration Pum and system monitoring functions: maximum ressure re-ressure/level motor rotection Dislay and indication functions: green indicator lights for mode of oeration indications (automatic or manual) and red indicator lights for fault indications otential-free changeover contact for fault signal. TM00 9732 0297 Protection: A ressure switch or a level switch at the suction side can be used as dry-running rotection. When the water level or ressure has been restored, automatic or manual resetting is ossible. Time control: To adat the booster set oeration to the actual conditions, the following settings can be made: Start-u delay: Sto delay: After run delay: Prevents simultaneous start-u of all ums. Prevents simultaneous sto of all ums. Kees ums in oeration after cut out ressure is reached. Time control is articularly convenient to reduce the number of starts and stos er hour, to revent water hammer and negative ressure in the suction manifold as well as other roblems that can arise under certain conditions. Comonents and materials TM00 9738 31 Two ums in oeration Three ums in oeration Cascade Ste ressure Pos. Descrition Number 1 Suction manifold 1 2 Discharge manifold 1 3 Base frame 1 4 Stand 1 5 Control cabinet 1 6 CR ums 2-4 7 Non-return valve 1 er um 8 Isolating valve 2 er um 9 Pressure switch 1 er um 10 Pressure gauge 1 TM00 9741 0397 Fig. 3 Control 0 dislay Fig. 4 Construction of ydro 0 5
Product data ydro 0 G - X Enclosure class: Materials Manifolds: Baseframe/stand: Isolating valves: Non-return valve: Pums: Pum Motors: IP 55. Control box: IP 54. G = galvanized steel X = AISI 316 Stainless steel (for 2 ums and above). Galvanized steel Brass (ball tye) Cast iron (butterfly tye) Grundfos tye PNV: olyroylene Grundfos tye GNV/VMF: cast iron and stainless steel. Grundfos CR tye. The CR um is a non self-riming, vertical multistage centrifugal um fitted with a Grundfos standard motor. The um consists of a base and a um head. The chamber stack and the outer sleeve are secured between the um head and the base by means of staybolts. The base has suction and discharge orts on the same level (in-line). All ums are equied with a maintenance-free mechanical shaft seal. Motor Pum head Outer sleeve Staybolt Base GR7376 Shaft seal As standard the CR um is fitted with either a QQE shaft seal (Cartridge tye). Shaft seal Descrition Max. tem. range [ C] QQE O-ring (cartridge) (balanced seal), SiC/SiC, EPDM C to +1 C Motor The motor is a totally enclosed, fan-cooled, 2-ole Grundfos standard motor with rincial dimensions in accordance with the EN/IEC and DIN standards. Electrical tolerances according to EN 034/IEC 34. Electrical data Mounting u to 4 kw: from 5.5 kw: Motor rotection V 18, V 1. Insulation class: F. Enclosure class IP 55. z Standard voltages 3 x 2-2/3-415 V, for P 2 3 kw. 3 x 3-415 V, for P 2 4 kw. All motors are rotected by the control anel of the booster set. Three-hase Grundfos motors from 3 kw uwards have a built-in thermistor (PTC) according to DIN 482. Single-hase motors have a built-in thermal overload switch. Advantages and benefits The state-of-the-art advancements introduced into this new vertical multistage um generation offer the following benefits: igh efficency Low NPS Minimised energy cost Imroves suction caability Air handling Reduces risks of dry-running Allows to service the um directly on site New cartridge concet without dismantling it from the booster set mechanical seal nor disassembling the liquid end Allows to service the mechanical seal without Sacer couling disassembling the motor from the um (for 11 kw motor onwards) Provices high resistance to ressure ulses Sleeve sealing and withstands temerature fluctuations as well as external forces Wear resistance, imroved dry-running caability and handling of thermal shocks enable Silicon carbide bearings longer oerating time Strong axial locking force and high torque Reinforced shaft lock ring lock system enable robust and reliable oeration of rotating assembly Fig. 5 CR um 6
Product data ydro 0 G - X Materials CR 3, 5, 10, 15 and Descrition Materials EN/DIN AISI/ASTM Pum head Cast iron EN-GJL-0 Materials CR 32, 45, 64 and 90 Materials CRI, CRN The base, the um head cover as well as vital um comonents of CRI and CRN ums are made as follows: Dimensions and weights EN-JL10 ASTM 25B Shaft Stainless steel 1.41 AISI 316 AISI 431 Imeller Stainless steel 1.41 AISI 4 Chamber Stainless steel 1.41 AISI 4 Outer sleeve Stainless steel 1.41 AISI 4 Base Cast iron EN-GJL-0 EN-JL10 ASTM 25B Neck ring PTFE Rubber arts in um EPDM or FKM Descrition Materials EN/DIN AISI/ASTM Pum head Motor stool Cast iron EN-GJS-0-7 Cast iron EN-GJL-0 EN-3510 EN-JL10 ASTM -55-06 ASTM 25B Shaft Stainless steel 1.57 AISI 431 Imeller Stainless steel 1.41 AISI 4 Chamber Stainless steel 1.41 AISI 4 Outer sleeve Stainless steel 1.41 AISI 4 O-ring for outer sleeve EPDM or FKM Base Neck ring Bearing ring Bottom bearing ring Rubber arts Cast iron EN-GJS-0-7 Carbon-grahite filled PTFE Bronze TC/TC EPDM or FKM TC = Tungsten carbide (cemented). EN-JL10 ASTM -55-06 Descrition Materials EN/DIN AISI/ASTM CRI Imeller Stainless steel 1.41 AISI 4 Chamber Stainless steel 1.41 AISI 4 Outer sleeve Stainless steel 1.41 AISI 4 O-ring for outer sleeve EPDM or FKM CRN Imeller Stainless steel 1.41 AISI 316 Chamber Stainless steel 1.41 AISI 316 Outer sleeve Stainless steel 1.41 AISI 316 O-ring for outer sleeve EPDM or FKM All other arts and comonents are as er the revious tables. Dimensions and weights for ydro 0 G - X are stated at age 26 to 33. Please note that the dimensions stated may vary ± 10 mm and that all systems are sulied without vibration damers. The dimensions may vary following technological imrovements to the comonents and/or materials used. Construction ydro 0 G - X is built u on a common base frame. The ums are fixed to the base frame by means of bolts. The control cabinet is fixed to the base frame by means of a stand. A suction manifold is mounted on the suction side of the ums. An isolating valve and non-return valve are mounted between the suction manifold and the individual ums. The non-return valve may be mounted on the discharge side at request. A discharge manifold is mounted on the discharge side of the ums. An isolating valve is mounted between the discharge manifold and the individual ums. Installation The ydro 0 G - X booster unit has to be installed in a room rotected from freezing and that is roerly ventilated in order to ensure adequate cooling of the ums. The booster must be ositioned so as to leave sufficient free room in front and at the sides of it for testing and maintenance and it must be ositioned on a flat and even surface, for examle on concrete flooring or foundation base. Make sure, in any case, that any ossible waterhammers will not have damaging effects on the integrity of the unit. The ies connected to the booster must be adequately sized. In order to avoid resonance or mechanical stress due to incorrect alignment, exansion joints must be installed both on the discharge and on the suction manifold, if any. It is always necessary to install suorts for the ies on the discharge and suction sides of the unit, so that the weight of the iing does not come to bear on the manifolds or on the ums. Fig. 6 2 1. Exansion joints 2. Pie hangers. 1 Mechanical construction 1 2 2 TM00 7748 1996 7
Performance curves ydro 0 G - X with 1, 2, 3 or 4 ums CR 3 900 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 90 10 10 10 10 0 ydro 0 CR 3-15 z ISO 9906 Annex A CR 3-12 CR 3-10 CR 3-8 CR 3-7 CR 3-6 CR 3-5 0 2 4 6 8 10 12 14 16 18 Q [m³/h] 0 5 Q [l/s] TM02 2119 03Performance curves/ Technical data/ Electrical datacr 3 8
Technical data ydro 0 G - X with 1, 2, 3 or 4 ums CR 3 Electrical data, flow and settings No. of ums 1 2 3 4 Pum tye P 2 [kw] Motor Starting Flow [m 3 /h] Pressure switch settings [bar] I max [A] CR 3-5 0.37 0.98 DOL Ot. Max. PR 1 PR 2 PR 3 PR 4 Cut-in Cut-out Cut-in Cut-out Cut-in Cut-out Cut-in Cut-out 1.2 2.7 - - - - - - CR 3-6 0.37 0.98 2.0 3.5 - - - - - - CR 3-7 0.55 1.44 2.5 4.0 - - - - - - CR 3-8 0.75 1.89 2.8 4.5 3.0 4.5 - - - - - - CR 3-10 0.75 1.89 4.3 5.8 - - - - - - CR 3-12 1.1 2.65 5.5 7.0 - - - - - - CR 3-15 1.1 2.65 7.3 8.8 - - - - - - CR 3-5 0.37 0.98 1.2 2.7 0.9 2.4 - - - - CR 3-6 0.37 0.98 2.0 3.5 1.7 3.2 - - - - CR 3-7 0.55 1.44 2.5 4.0 2.2 3.7 - - - - CR 3-8 0.75 1.89 5.6 9.0 3.0 4.5 2.7 4.2 - - - - CR 3-10 0.75 1.89 4.3 5.8 4.0 5.5 - - - - CR 3-12 1.1 2.65 5.6 7.1 5.3 6.8 - - - - CR 3-15 1.1 2.65 7.5 9.0 7.2 8.7 - - - - CR 3-5 0.37 0.98 1.2 2.7 0.9 2.4 0.6 2.1 - - CR 3-6 0.37 0.98 2.0 3.5 1.7 3.2 1.4 2.9 - - CR 3-7 0.55 1.44 2.5 4.0 2.2 3.7 1.9 3.4 - - CR 3-8 0.75 1.89 8.4 15.5 3.2 4.7 2.9 4.4 2.6 4.1 - - CR 3-10 0.75 1.89 4.5 6.0 4.2 5.7 3.9 5.4 - - CR 3-12 1.1 2.65 5.9 7.4 5.6 7.1 5.3 6.8 - - CR 3-15 1.1 2.65 7.8 9.3 7.5 9.0 7.2 8.7 - - CR 3-5 0.37 0.98 1.2 2.7 0.9 2.4 0.6 2.1 0.3 1.8 CR 3-6 0.37 0.98 2.0 3.5 1.7 3.2 1.4 2.9 1.1 2.6 CR 3-7 0.55 1.44 2.5 4.0 2.2 3.7 1.9 3.4 1.6 3.1 CR 3-8 0.75 1.89 11.2 18.0 3.2 4.7 2.9 4.4 2.6 4.1 2.3 3.8 CR 3-10 0.75 1.89 4.5 6.0 4.2 5.7 3.9 5.4 3.6 5.1 CR 3-12 1.1 2.65 5.9 7.4 5.6 7.1 5.3 6.8 5.0 6.5 CR 3-15 1.1 2.65 7.8 9.3 7.5 9.0 7.2 8.7 6.9 8.4 DOL: direct on line. 9
Performance curves ydro 0 G - X with 1, 2, 3 or 4 ums CR 5 900 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 90 10 10 0 ydro 0 CR 5-15 z ISO 9906 Annex A CR 5-13 CR 5-10 CR 5-9 CR 5-8 CR 5-7 CR 5-5 0 4 8 12 16 24 28 32 Q [m³/h] 0 2 4 6 8 Q [l/s] TM02 2132 03CR 5 10
Technical data ydro 0 G - X with 1, 2, 3 or 4 ums CR 5 Electrical data, flow and settings No. of ums 1 2 3 4 Pum tye P 2 [kw] Motor Starting Flow [m 3 /h] Pressure switch settings [bar] I max [A] CR 5-5 0.75 1.88 DOL Ot. Max. PR 1 PR 2 PR 3 PR 4 Cut-in Cut-out Cut-in Cut-out Cut-in Cut-out Cut-in Cut-out 1.4 2.9 - - - - - - CR 5-7 1.1 2.65 2.5 4.0 - - - - - - CR 5-8 1.1 2.65 3.1 4.6 - - - - - - CR 5-9 1.5 3.4 5.5 8.5 4.0 5.5 - - - - - - CR 5-10 1.5 3.4 4.5 6.0 - - - - - - CR 5-13 2.2 4.75 6.5 8.0 - - - - - - CR 5-15 2.2 4.75 7.5 9.0 - - - - - - CR 5-5 0.75 1.88 1.4 2.9 1.1 2.6 - - - - CR 5-7 1.1 2.65 2.7 4.2 2.4 3.9 - - - - CR 5-8 1.1 2.65 3.3 4.8 3.0 4.5 - - - - CR 5-9 1.5 3.4 11.0 17.0 4.2 5.7 3.9 5.4 - - - - CR 5-10 1.5 3.4 4.8 6.3 4.5 6.0 - - - - CR 5-13 2.2 4.75 6.8 8.3 6.5 8.0 - - - - CR 5-15 2.2 4.75 8.2 9.7 7.9 9.4 - - - - CR 5-5 0.75 1.88 1.4 2.9 1.1 2.6 0.8 2.3 - - CR 5-7 1.1 2.65 2.7 4.2 2.4 3.9 2.1 3.6 - - CR 5-8 1.1 2.65 3.3 4.8 3.0 4.5 2.7 4.2 - - CR 5-9 1.5 3.4 16.5 25.5 4.2 5.7 3.9 5.4 3.6 5.1 - - CR 5-10 1.5 3.4 4.8 6.3 4.5 6.0 4.2 5.7 - - CR 5-13 2.2 4.75 6.8 8.3 6.5 8.0 6.2 7.7 - - CR 5-15 2.2 4.75 8.2 9.7 7.9 9.4 7.6 9.1 - - CR 5-5 0.75 1.88 1.4 2.9 1.1 2.6 0.8 2.3 0.5 2.0 CR 5-7 1.1 2.65 2.7 4.2 2.4 3.9 2.1 3.6 1.8 3.3 CR 5-8 1.1 2.65 3.3 4.8 3.0 4.5 2.7 4.2 2.4 3.9 CR 5-9 1.5 3.4 22.0 34.0 4.2 5.7 3.9 5.4 3.6 5.1 3.3 4.8 CR 5-10 1.5 3.4 4.8 6.3 4.5 6.0 4.2 5.7 3.9 5.4 CR 5-13 2.2 4.75 6.8 8.3 6.5 8.0 6.2 7.7 5.9 7.4 CR 5-15 2.2 4.75 8.2 9.7 7.9 9.4 7.6 9.1 7.3 8.8 DOL: direct on line. 11
Performance curves ydro 0 G - X with 1, 2, 3 or 4 ums CR 10 900 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 90 90 10 10 0 ydro 0 CR 10-10 z ISO 9906 Annex A CR 10-9 CR 10-8 CR 10-7 CR 10-6 CR 10-5 CR 10-4 CR 10-3 0 5 10 15 25 35 45 Q [m³/h] 0 2 4 6 8 10 12 14 Q [l/s] TM02 7779 03CR 10 12
Technical data ydro 0 G - X with 1, 2, 3 or 4 ums CR 10 Electrical data, flow and settings No. of ums 1 2 3 4 Pum tye P 2 [kw] Motor Starting Flow [m 3 /h] Pressure switch settings [bar] I max [A] CR 10-3 1.1 2.7 DOL Ot. Max. PR 1 PR 2 PR 3 PR 4 Cut-in Cut-out Cut-in Cut-out Cut-in Cut-out Cut-in Cut-out 1.5 2.5 - - - - - - CR 10-4 1.5 3.4 2.6 3.6 - - - - - - CR 10-5 2.2 4.8 3.6 4.6 - - - - - - CR 10-6 2.2 4.8 4.4 5.6 - - - - - - 10.0 12.0 CR 10-7 3.0 6.3 5.2 6.4 - - - - - - CR 10-8 3.0 6.3 6.0 7.2 - - - - - - CR 10-9 3.0 6.3 6.3 7.8 - - - - - - CR 10-10 4.0 8.0 7.3 8.8 - - - - - - CR 10-3 1.1 2.7 1.5 2.5 1.3 2.3 - - - - CR 10-4 1.5 3.4 2.6 3.6 2.4 3.4 - - - - CR 10-5 2.2 4.8 3.6 4.6 3.3 4.3 - - - - CR 10-6 2.2 4.8 4.4 5.6 4.0 5.2 - - - -.0 24.0 CR 10-7 3.0 6.3 5.2 6.4 4.8 6.0 - - - - CR 10-8 3.0 6.3 6.0 7.2 5.5 6.7 - - - - CR 10-9 3.0 6.3 6.3 7.8 5.8 7.3 - - - - CR 10-10 4.0 8.0 7.3 8.8 6.8 8.3 - - - - CR 10-3 1.1 2.7 1.5 2.5 1.3 2.3 1.1 2.1 - - CR 10-4 1.5 3.4 2.6 3.6 2.4 3.4 2.2 3.2 - - CR 10-5 2.2 4.8 3.6 4.6 3.3 4.3 3.0 4.0 - - CR 10-6 2.2 4.8 4.4 5.6 4.0 5.2 3.6 4.8 - -.0 36.0 CR 10-7 3.0 6.3 5.2 6.4 4.8 6.0 4.4 5.6 - - CR 10-8 3.0 6.3 6.0 7.2 5.5 6.7 5.0 6.2 - - CR 10-9 3.0 6.3 6.3 7.8 5.8 7.3 5.3 6.8 - - CR 10-10 4.0 8.0 7.3 8.8 6.8 8.3 6.3 7.8 - - CR 10-3 1.1 2.7 1.5 2.5 1.3 2.3 1.1 2.1 0.9 1.9 CR 10-4 1.5 3.4 2.6 3.6 2.4 3.4 2.2 3.2 2.0 3.0 CR 10-5 2.2 4.8 3.6 4.6 3.3 4.3 3.0 4.0 2.7 3.7 CR 10-6 2.2 4.8 4.4 5.6 4.0 5.2 3.6 4.8 3.2 4.4.0 48.0 CR 10-7 3.0 6.3 5.2 6.4 4.8 6.0 4.4 5.6 4.0 5.2 CR 10-8 3.0 6.3 6.0 7.2 5.5 6.7 5.0 6.2 4.5 5.7 CR 10-9 3.0 6.3 6.3 7.8 5.8 7.3 5.3 6.8 4.8 6.3 CR 10-10 4.0 8.0 7.3 8.8 6.8 8.3 6.3 7.8 5.8 7.3 Booster sets with these ums have ressure switches factory set within the oerating ressure safety limit. DOL: direct on line. Starting configuration other than standard available on request. 13
Performance curves ydro 0 G - X with 1, 2, 3 or 4 ums CR 15 0 900 0 0 0 0 900 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 110 90 90 10 10 0 ydro 0 CR 15-8 z ISO 9906 Annex A CR 15-7 CR 15-6 CR 15-5 CR 15-4 CR 15-3 CR 15-2 0 10 90 Q [m³/h] 0 5 10 15 25 Q [l/s] TM02 77 03CR 15 14
Technical data ydro 0 G - X with 1, 2, 3 or 4 ums CR 15 Electrical data, flow and settings No. of ums 1 2 3 4 Pum tye P 2 [kw] Motor Starting Flow [m 3 /h] Pressure switch settings [bar] I max [A] CR 15-2 2.2 4.8 DOL Ot. Max. PR 1 PR 2 PR 3 PR 4 Cut-in Cut-out Cut-in Cut-out Cut-in Cut-out Cut-in Cut-out 1.7 2.5 - - - - - - CR 15-3 3.0 6.3 2.8 3.8 - - - - - - CR 15-4 4.0 8.0 4.2 5.2 - - - - - - CR 15-5 4.0 8.0 22.0 27.0 5.4 6.6 - - - - - - CR 15-6 5.5 11.0 6.3 7.5 - - - - - - CR 15-7 5.5 11.0 7.1 8.3 - - - - - - CR 15-8 7.5 15.2 7.8 9.3 - - - - - - CR 15-2 2.2 4.8 1.7 2.5 1.5 2.3 - - - - CR 15-3 3.0 6.3 2.8 3.8 2.6 3.6 - - - - CR 15-4 4.0 8.0 4.2 5.2 3.8 4.8 - - - - CR 15-5 4.0 8.0 44.0 54.0 5.4 6.6 4.9 6.1 - - - - CR 15-6 5.5 11.0 6.3 7.5 5.8 7.0 - - - - CR 15-7 5.5 11.0 7.1 8.3 6.6 7.8 - - - - CR 15-8 7.5 15.2 7.8 9.3 7.3 8.8 - - - - CR 15-2 2.2 4.8 1.7 2.5 1.5 2.3 1.3 2.1 - - CR 15-3 3.0 6.3 2.8 3.8 2.6 3.6 2.4 3.4 - - CR 15-4 4.0 8.0 4.2 5.2 3.8 4.8 3.4 4.4 - - CR 15-5 4.0 8.0 66.0 81.0 5.4 6.6 4.9 6.1 4.4 5.6 - - CR 15-6 5.5 11.0 6.3 7.5 5.8 7.0 5.3 6.5 - - CR 15-7 5.5 11.0 7.1 8.3 6.6 7.8 6.1 7.3 - - CR 15-8 7.5 15.2 7.8 9.3 7.3 8.8 6.8 8.3 - - CR 15-2 2.2 4.8 1.7 2.5 1.5 2.3 1.3 2.1 1.1 1.9 CR 15-3 3.0 6.3 2.8 3.8 2.6 3.6 2.4 3.4 2.2 3.2 CR 15-4 4.0 8.0 4.2 5.2 3.8 4.8 3.4 4.4 3.0 4.0 CR 15-5 4.0 8.0 88.0 108.0 5.4 6.6 4.9 6.1 4.4 5.6 3.9 5.1 CR 15-6 5.5 11.0 6.3 7.5 5.8 7.0 5.3 6.5 4.8 6.0 CR 15-7 5.5 11.0 7.1 8.3 6.6 7.8 6.1 7.3 5.6 6.8 CR 15-8 7.5 15.2 7.8 9.3 7.3 8.8 6.8 8.3 6.3 7.8 Booster sets with these ums have ressure switches factory set within the oerating ressure safety limit. DOL: direct on line. Starting configuration other than standard available on request. 15
Performance curves ydro 0 G - X with 1, 2, 3 or 4 ums CR 900 0 90 ydro 0 CR -7 z ISO 9906 Annex A 0 0 0 0 900 90 CR -6 0 0 0 0 0 0 CR -5 0 0 0 0 0 CR -4 0 0 0 0 0 CR -3 0 0 0 10 CR -2 0 10 0 0 0 10 90 110 Q [m³/h] 0 5 10 15 25 Q [l/s] TM02 7781 03CR 16
Technical data ydro 0 G - X with 1, 2, 3 or 4 ums CR Electrical data, flow and settings No. of ums 1 2 3 Pum tye P 2 [kw] Motor Starting Flow [m 3 /h] Pressure switch settings [bar] I max [A] DOL Ot. Max. PR 1 PR 2 PR 3 PR 4 Cut-in Cut-out Cut-in Cut-out Cut-in Cut-out Cut-in Cut-out CR -2 2.2 4.8 1.7 2.5 - - - - - - CR -3 4.0 8.0 2.9 3.9 - - - - - - CR -4 5.5 11.0 4.1 5.3 - - - - - - 22.0 27.0 CR -5 5.5 11.0 5.2 6.4 - - - - - - CR -6 7.5 15.2 6.1 7.3 - - - - - - CR -7 7.5 15.2 6.8 8.3 - - - - - - CR -2 2.2 4.8 1.7 2.5 1.5 2.3 - - - - CR -3 4.0 8.0 2.9 3.9 2.6 3.6 - - - - CR -4 5.5 11.0 4.1 5.3 3.7 4.9 - - - - 44.0 54.0 CR -5 5.5 11.0 5.2 6.4 4.7 5.9 - - - - CR -6 7.5 15.2 6.1 7.3 5.6 6.8 - - - - CR -7 7.5 15.2 6.8 8.3 6.3 7.8 - - - - CR -2 2.2 4.8 1.7 2.5 1.5 2.3 1.3 2.1 - - CR -3 4.0 8.0 2.9 3.9 2.6 3.6 2.3 3.3 - - CR -4 5.5 11.0 4.1 5.3 3.7 4.9 3.3 4.5 - - 66.0 81.0 CR -5 5.5 11.0 5.2 6.4 4.7 5.9 4.2 5.4 - - CR -6 7.5 15.2 6.1 7.3 5.6 6.8 5.1 6.3 - - CR -7 7.5 15.2 6.8 8.3 6.3 7.8 5.8 7.3 - - CR -2 2.2 4.8 1.7 2.5 1.5 2.3 1.3 2.1 1.1 1.9 CR -3 4.0 8.0 2.9 3.9 2.6 3.6 2.3 3.3 2.0 3.0 4 CR -4 5.5 11.0 4.1 5.3 3.7 4.9 3.3 4.5 2.9 4.1 88.0 108.0 CR -5 5.5 11.0 5.2 6.4 4.7 5.9 4.2 5.4 3.7 4.9 CR -6 7.5 15.2 6.1 7.3 5.6 6.8 5.1 6.3 4.6 5.8 CR -7 7.5 15.2 6.8 8.3 6.3 7.8 5.8 7.3 5.3 6.8 Booster sets with these ums have ressure switches factory set within the oerating ressure safety limit. DOL: direct on line. Starting configuration other than standard available on request. 17
Performance curves ydro 0 G - X with 1, 2, 3 or 4 ums CR 32 1 0 900 1 110 90 ydro 0 CR 32-6 z ISO 9906 Annex A 0 0 0 0 900 0 0 0 0 0 0 0 0 0 0 0 90 CR 32-5 CR 32-4 CR 32-3 0 0 0 CR 32-2 0 0 0 10 CR 32-2-2 0 10 0 0 0 1 1 1 Q [m³/h] 0 10 Q [l/s] TM01 3610 03CR 32 18
Technical data ydro 0 G - X with 1, 2, 3 or 4 ums CR 32 Electrical data, flow and settings No. of ums 1 2 3 4 Pum tye P 2 [kw] Motor Starting Flow [m 3 /h] Pressure switch settings [bar] I max [A] CR 32-2-2 3.0 6.3 - DOL SD Ot. Max. PR 1 PR 2 PR 3 PR 4 Cut-in Cut-out Cut-in Cut-out Cut-in Cut-out Cut-in Cut-out 1.2 3.0 - - - - - - CR 32-2 4.0 8.0-2.3 3.8 - - - - - - CR 32-3 5.5 11.0-4.0 5.5 - - - - - - 32.0.0 CR 32-4 7.5 15.2-6.0 7.5 - - - - - - CR 32-5 11.0 21.5-7.0 8.8 - - - - - - CR 32-6 11.0 21.5-8.0 10.0 - - - - - - CR 32-2-2 3.0 6.3-1.5 3.0 1.0 2.5 - - - - CR 32-2 4.0 8.0-2.3 3.8 2.0 3.5 - - - - CR 32-3 5.5 11.0-4.0 5.5 3.7 5.2 - - - - 64.0.0 CR 32-4 7.5 15.2-6.0 7.5 5.5 7.0 - - - - CR 32-5 11.0 21.5-7.0 8.8 6.5 8.0 - - - - CR 32-6 11.0 21.5-8.5 10.0 8.0 9.5 - - - - CR 32-2-2 3.0 6.3-1.5 3.0 1.2 2.7 1.0 2.5 - - CR 32-2 4.0 8.0-2.3 3.8 2.0 3.5 1.8 3.3 - - CR 32-3 5.5 11.0-4.2 5.7 3.2 4.5 2.9 4.2 - - 96.0 1.0 CR 32-4 7.5 15.2-6.0 7.5 5.0 7.0 4.0 5.5 - - CR 32-5 11.0 21.5-7.0 8.8 6.5 8.0 5.5 7.0 - - CR 32-6 11.0 21.5-8.5 10.0 8.0 9.5 7.0 8.5 - - CR 32-2-2 3.0 6.3-1.4 2.9 1.2 2.7 1.0 2.5 0.8 2.3 CR 32-2 4.0 8.0-2.2 3.7 2.0 3.5 1.8 3.3 1.6 3.1 CR 32-3 5.5 11.0-4.2 5.7 3.2 4.5 2.9 4.2 2.6 3.9 128.0 1.0 CR 32-4 7.5 15.2-6.0 7.5 5.0 7.0 4.0 5.5 4.5 6.0 CR 32-5 11.0 21.5-7.0 8.5 6.5 8.0 5.5 7.0 5.5 7.0 CR 32-6 11.0 21.5-8.5 10.0 8.0 9.5 7.0 8.5 6.0 7.5 Booster sets with these ums have ressure switches factory set within the oerating ressure safety limit. DOL: direct on line. SD: star/delta. Starting configuration other than standard available on request. 19
Performance curves ydro 0 G - X with 1, 2, 3 or 4 ums CR 45 0 900 0 0 0 0 0 0 0 0 0 0 0 90 ydro 0 CR 45-4 z ISO 9906 Annex A CR 45-3 CR 45-2 0 0 0 0 0 CR 45-2-2 0 0 10 CR 45-1 0 10 0 0 0 1 1 1 1 0 2 Q [m³/h] 0 10 Q [l/s] TM01 3611 03CR 45
Technical data ydro 0 G - X with 1, 2, 3 or 4 ums CR 45 Electrical data, flow and settings No. of ums 1 2 3 4 Pum tye P 2 [kw] Motor Starting Flow [m 3 /h] Pressure switch settings [bar] I max [A] CR 45-1 4.0 8.0 - DOL SD Ot. Max. PR 1 PR 2 PR 3 PR 4 Cut-in Cut-out Cut-in Cut-out Cut-in Cut-out Cut-in Cut-out 0.8 2.2 - - - - - - CR 45-2-2 5.5 11.0-2.3 3.8 - - - - - - CR 45-2 7.5 15.2-45.0 58.0 3.0 4.5 - - - - - - CR 45-3 11.0 21.5-5.8 7.2 - - - - - - CR 45-4 15.0 28.7-8.0 9.5 - - - - - - CR 45-1 4.0 8.0-0.8 2.2 0.6 2.0 - - - - CR 45-2-2 5.5 11.0-2.3 3.8 1.8 3.3 - - - - CR 45-2 7.5 15.2-90.0 116.0 3.0 4.5 2.5 4.0 - - - - CR 45-3 11.0 21.5-5.8 7.2 4.5 6.0 - - - - CR 45-4 15.0 28.7-8.0 9.5 7.5 9.0 - - - - CR 45-1 4.0 8.0-0.8 2.2 0.6 2.0 0.4 1.8 - - CR 45-2-2 5.5 11.0-2.3 3.8 1.8 3.3 1.3 2.8 - - CR 45-2 7.5 15.2-135.0 174.0 3.0 4.5 2.5 4.0 2.0 3.5 - - CR 45-3 11.0 21.5-5.8 7.2 5.0 6.5 4.5 6.0 - - CR 45-4 15.0 28.7-8.0 9.5 7.5 9.0 7.0 8.5 - - CR 45-1 4.0 8.0-0.8 2.2 0.7 2.0 0.6 1.8 0.5 1.6 CR 45-2-2 5.5 11.0-2.3 3.8 1.8 3.3 1.3 2.8 0.8 2.3 CR 45-2 7.5 15.2-1.0 232.0 3.0 4.5 2.5 4.0 2.0 3.5 1.5 3.0 CR 45-3 11.0 21.5-5.8 7.2 5.0 6.5 4.5 6.0 4.0 5.5 CR 45-4 15.0 28.7-8.0 9.5 7.5 9.0 7.0 8.5 6.5 8.0 Booster sets with these ums have ressure switches factory set within the oerating ressure safety limit. DOL: direct on line. SD: star/delta. Starting configuration other than standard available on request. 21
Performance curves ydro 0 G - X with 1, 2, 3 or 4 ums CR 64 10 1 0 900 0 0 0 0 900 0 0 1 110 90 90 ydro 0 CR 64-4 z ISO 9906 Annex A CR 64-4-2 0 0 0 CR 64-3-1 0 0 0 0 0 CR 64-2 0 0 0 0 CR 64-2-2 0 0 10 0 1 1 0 2 2 3 3 Q [m³/h] 0 Q [l/s] TM01 3612 03CR 64 22
Technical data ydro 0 G - X with 1, 2, 3 or 4 ums CR 64 Electrical data, flow and settings No. of ums 1 2 3 4 Pum tye P 2 [kw] Motor Starting Flow [m 3 /h] Pressure switch settings [bar] I max [A] CR 64-2-2 7.5 15.2 - DOL SD Ot. Max. PR 1 PR 2 PR 3 PR 4 Cut-in Cut-out Cut-in Cut-out Cut-in Cut-out Cut-in Cut-out 2.2 3.7 - - - - - - CR 64-2 11.0 21.5-3.8 5.2 - - - - - - CR 64-3-1 15.0 28.7-64.0 85.0 5.3 6.8 - - - - - - CR 64-4-2 18.5 35.9-7.0 8.5 - - - - - - CR 64-4 22.0 42.0-8.0 9.5 - - - - - - CR 64-2-2 7.5 15.2-2.2 3.7 1.9 3.4 - - - - CR 64-2 11.0 21.5-3.8 5.2 3.3 4.8 - - - - CR 64-3-1 15.0 28.7-128.0 1.0 5.3 6.8 4.5 6.0 - - - - CR 64-4-2 18.5 35.9-7.0 8.5 6.5 8.0 - - - - CR 64-4 22.0 42.0-8.0 9.5 7.5 9.0 - - - - CR 64-2-2 7.5 15.2-2.2 3.7 1.9 3.4 1.5 3.0 - - CR 64-2 11.0 21.5-3.8 5.2 3.3 4.8 2.5 4.0 - - CR 64-3-1 15.0 28.7-192.0 265.0 5.3 6.8 4.5 6.0 4.2 5.5 - - CR 64-4-2 18.5 35.9-7.0 8.5 6.5 8.0 6.0 7.5 - - CR 64-4 22.0 42.0-8.0 9.5 7.5 9.0 7.0 8.5 - - CR 64-2-2 7.5 15.2-2.2 3.7 1.9 3.4 1.5 3.0 1.0 2.5 CR 64-2 11.0 21.5-3.8 5.2 3.3 4.8 2.5 4.0 2.0 3.5 CR 64-3-1 15.0 28.7-256.0 3.0 5.3 6.8 4.5 6.0 4.0 5.5 3.5 5.0 CR 64-4-2 18.5 35.9-7.0 8.5 6.5 8.0 6.0 7.5 5.5 7.0 CR 64-4 22.0 42.0-8.0 9.5 7.5 9.0 7.0 8.5 6.5 8.0 Booster sets with these ums have ressure switches factory set within the oerating ressure safety limit. DOL: direct on line. SD: star/delta. Starting configuration other than standard available on request. 23
Performance curves ydro 0 G - X with 1, 2, 3 or 4 ums CR 90 0 900 0 0 0 0 0 900 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 110 90 90 10 0 10 0 ydro 0 CR 90-4-2 z ISO 9906 Annex A CR 90-3 CR 90-3-2 CR 90-2 CR 90-2-2 CR 90-1 0 1 0 2 0 3 0 4 0Q [m³/h] 0 1 1 Q [l/s] TM01 3613 03CR 90 24
Technical data ydro 0 G - X with 1, 2, 3 or 4 ums CR 90 Electrical data, flow and settings No. of ums 1 2 3 4 Pum tye P 2 [kw] Motor Starting Flow [m 3 /h] Pressure switch settings [bar] I max [A] CR 90-1 7.5 15.2 - DOL SD Ot. Max. PR 1 PR 2 PR 3 PR 4 Cut-in Cut-out Cut-in Cut-out Cut-in Cut-out Cut-in Cut-out 1.2 2.6 - - - - - - CR 90-2-2 11.0 21.5-3.0 4.5 - - - - - - CR 90-2 15.0 28.7-3.5 5.0 - - - - - - 90.0 1.0 CR 90-3-2 18.5 35.9-4.5 6.0 - - - - - - CR 90-3 22.0 42.0-5.5 7.0 - - - - - - CR 90-4-2.0 56.0-7.0 8.5 - - - - - - CR 90-1 7.5 15.2-1.2 2.6 1.1 2.4 - - - - CR 90-2-2 11.0 21.5-3.0 4.5 2.5 4.0 - - - - CR 90-2 15.0 28.7-3.5 5.0 3.0 4.5 - - - - 1.0 2.0 CR 90-3-2 18.5 35.9-4.5 6.0 4.5 6.0 - - - - CR 90-3 22.0 42.0-5.5 7.0 5.0 6.5 - - - - CR 90-4-2.0 56.0-7.0 8.5 6.5 8.0 - - - - CR 90-1 7.5 15.2-1.2 2.6 1.1 2.4 1.0 2.2 - - CR 90-2-2 11.0 21.5-3.0 4.5 2.5 4.0 2.0 3.5 - - CR 90-2 15.0 28.7-3.5 5.0 3.0 4.5 2.5 4.0 - - 2.0 3.0 CR 90-3-2 18.5 35.9-4.5 6.0 4.5 6.0 4.0 5.5 - - CR 90-3 22.0 42.0-5.5 7.0 5.0 6.5 4.5 6.0 - - CR 90-4-2.0 56.0-7.0 8.5 6.5 8.0 6.0 7.5 - - CR 90-1 7.5 15.2-1.2 2.6 1.1 2.4 1.0 2.2 0.9 2.0 CR 90-2-2 11.0 21.5-3.0 4.5 2.5 4.0 2.0 3.5 1.5 3.0 CR 90-2 15.0 28.7-3.5 5.0 3.0 4.5 2.5 4.0 2.0 3.5 3.0 4.0 CR 90-3-2 18.5 35.9-4.5 6.0 4.5 6.0 4.0 5.5 3.5 5.0 CR 90-3 22.0 42.0-5.5 7.0 5.0 6.5 4.5 6.0 4.0 5.5 CR 90-4-2.0 56.0-7.0 8.5 6.5 8.0 6.0 7.5 5.5 7.0 Booster sets with these ums have ressure switches factory set within the oerating ressure safety limit. DOL: direct on line. SD: star/delta. Starting configuration other than standard available on request. 25
Dimensions and weights ydro 0 G 1 um Booster set with 1 um CR 3 - CR 5 - CR 10 Q A B B2 L TM02 2131 02Booster set with 1 um Pum tye Connections L Weight B B2 A Q G X G X [kg] 1 CR 3-5 523 35 1 CR 3-6 541 36 1 CR 3-7 559 36 1 CR 3-8 R 1 R 1½ 623 0 0 4 90 745 621 38 1 CR 3-10 657 39 1 CR 3-12 693 41 1 CR 3-15 747 43 1 CR 5-5 612 38 1 CR 5-7 666 1 CR 5-8 693 42 1 CR 5-9 R 1¼ R 1¼ 6 0 0 4 90 745 786 43 1 CR 5-10 813 1 CR 5-13 894 1 CR 5-15 948 63 1 CR 10-3 648 56 1 CR 10-4 744 61 1 CR 10-5 774 61 1 CR 10-6 4 63 R 1½ R 1½ 776 766 0 4 1 745 1 CR 10-7 893 1 CR 10-8 923 71 1 CR 10-9 953 72 1 CR 10-10 10 85 Note: Dimensions may vary ± 10 mm. Use of vibration damers influences total height. G = Galvanised manifolds. X = AISI 316 Stainless steel manifolds. 26
Dimensions and weights ydro 0 G 1 um Booster set with 1 um CR 15 - CR - CR 32 - CR 45 - CR 64 - CR 90 Q L A B2 TM02 2123 31 Pum tye Connections B2 Weight L A Q G X G X [kg] 1 CR 15-2 761 111 1 CR 15-3 8 119 1 CR 15-4 DN 942 133 1 CR 15-5 DN PN 10 987 138 7 756 756 1 1455 1 CR 15-6 1083 157 1 CR 15-7 1128 1 1 CR 15-8 DN 1235 175 1 CR -2 761 111 1 CR -3 897 132 DN 1 CR -4 993 157 DN PN 10 1 CR -5 7 756 756 1 1455 1038 156 1 CR -6 1088 161 1 CR -7 DN 1128 174 1 CR 32-2-2 9 1 1 CR 32-2 1096 193 DN 65 1 CR 32-3 1096 9 DN 65 PN 10 1 CR 32-4 900 828 828 165 1455 1166 222 1 CR 32-5 1419 261 1 CR 32-6 DN 65 1489 265 1 CR 45-1 990 185 1 CR 45-2-2 1089 213 DN DN 900 1 CR 45-2 875 875 0 1455 1089 2 PN 10 1 CR 45-3 1352 266 1 CR 45-4 1066 1446 1 1 CR 64-2-2 1095 255 900 1 CR 64-2 DN 1278 9 1 CR 64-3-1 DN PN 10 1374 3 893 893 0 1455 1 CR 64-4-2 1457 335 1066 DN 1 CR 64-4 1579 343 1 CR 90-1 1022 2 1 CR 90-2-2 DN 1297 298 1 CR 90-2 DN PN 10 1311 337 1066 908 908 0 1455 1 CR 90-3-2 1043 352 1 CR 90-3 DN 1525 352 1 CR 90-4-2 1684 490 Note: Dimensions may vary ± 10 mm. Use of vibration damers influences total height. G = Galvanised manifolds. X = AISI 316 Stainless steel manifolds. 27
Dimensions and weights ydro 0 G - X 2 ums Booster set with 2 ums CR 3 - CR 5 - CR 10 L Q A B1 B2 TM02 2128 31Booster set with 2 ums Pum tye Connections B1 B2 Weight L A Q G X G X G X [kg] 2 CR 3-5 548 90 2 CR 3-6 566 92 2 CR 3-7 584 92 2 CR 3-8 G 1½ G 2 0 496 5 544 0 115 11/ 10 646 96 2 CR 3-10 682 98 2 CR 3-12 718 102 2 CR 3-15 772 106 2 CR 5-5 637 94 2 CR 5-7 691 98 2 CR 5-8 718 102 2 CR 5-9 G 2 G 2 0 536 568 596 628 115 11/ 10 811 104 2 CR 5-10 838 118 2 CR 5-13 919 118 2 CR 5-15 973 124 2 CR 10-3 673 132 2 CR 10-4 769 142 2 CR 10-5 799 142 2 CR 10-6 11/ 829 146 G 2½ G 2½ 6 6 679 716 752 145 2 CR 10-7 10 918 1 2 CR 10-8 948 162 2 CR 10-9 978 164 2 CR 10-10 1045 197 Note: Dimensions may vary ± 10 mm. Use of vibration damers influences total height. G = Galvanised manifolds. X = AISI 316 Stainless steel manifolds. 28
Dimensions and weights ydro 0 G - X 2 ums Booster set with 2 ums CR 15 - CR - CR 32 - CR 45 - CR 64 - CR 90 A Q Q L B1 L2 B2 Front mounted control cabinet TM02 2124 31 A L2 B1 L B2 Side mounted control cabinet TM02 2125 31 Front mounted control cabinet Pum tye Connections B1 B2 Weight L L2 A Q G X G X G X [kg] 2 CR 15-2 761 191 2 CR 15-3 8 2 2 CR 15-4 DN 942 234 2 CR 15-5 DN PN 10 11/ 987 244 7 0 746 746 946 946 1 2 CR 15-6 10 1083 282 2 CR 15-7 1128 288 2 CR 15-8 DN 1235 294 2 CR -2 761 191 2 CR -3 897 232 DN 2 CR -4 993 282 DN PN 10 11/ 2 CR -5 7 0 746 746 946 946 1 10 1038 2 2 CR -6 1088 290 2 CR -7 DN 1128 292 2 CR 32-2-2 9 329 2 CR 32-2 DN DN 11/ 1096 347 900 0 856 856 1076 1076 165 2 CR 32-3 PN 10 10 1096 365 2 CR 32-4 1166 381 2 CR 45-1 990 3 DN 1 DN 1 2 CR 45-2-2 900 0 3 948 1288 1233 0 1089 368 PN 10 11/ 2 CR 45-2 10 1089 378 2 CR 64-2-2 DN 1 DN 1 PN 10 900 0 1021 1089 16 1374 0 1278 448 Side mounted control cabinet Pum tye Connections B1 B2 Weight L L2 A Q G X G X G X [kg] 2 CR 32-5 DN DN 1419 433 1616 0 856 856 1076 1076 165 1455 2 CR 32-6 1489 441 2 CR 45-3 DN 1 DN 1 1352 4 1616 0 3 948 1288 1233 0 1455 2 CR 45-4 PN 10 1446 482 2 CR 64-2 1278 448 DN 1 2 CR 64-3-1 1374 524 DN 1 PN 10 2 CR 64-4-2 1616 0 1021 1089 16 1374 0 1455 1457 5 2 CR 64-4 DN 1 1579 656 2 CR 90-1 1022 3 2 CR 90-2-2 DN 1 1297 464 2 CR 90-2 DN 1 1311 5 1616 0 1036 1104 1321 1389 0 1455 2 CR 90-3-2 13 558 2 CR 90-3 DN 1 1525 664 2 CR 90-4-2 1684 8 Note: Dimensions may vary ± 10 mm. Use of vibration damers influences total height. G = Galvanised manifolds. X = AISI 316 Stainless steel manifolds. 29
Dimensions and weights ydro 0 G - X 3 ums Booster set with 3 ums CR 3 - CR 5 - CR 10 L2 L Q A B1 B2 TM02 2129 31Booster set with 3 ums Pum tye Connections B1 B2 Weight L L2 A Q G X G X G X [kg] 3 CR 3-5 548 123 3 CR 3-6 566 126 3 CR 3-7 584 129 3 CR 3-8 G 1½ G 2 13 9 496 5 544 0 115 1455 646 132 3 CR 3-10 682 135 3 CR 3-12 718 147 3 CR 3-15 772 147 3 CR 5-5 637 123 3 CR 5-7 691 129 3 CR 5-8 718 135 3 CR 5-9 G 2 G 2 13 9 536 568 596 628 115 1455 811 138 3 CR 5-10 838 177 3 CR 5-13 919 177 3 CR 5-15 973 181 3 CR 10-3 673 195 3 CR 10-4 769 193 3 CR 10-5 793 193 3 CR 10-6 829 1 G 2½ G 2½ 10 9 6 679 716 752 145 1455 3 CR 10-7 918 211 3 CR 10-8 948 214 3 CR 10-9 978 217 3 CR 10-10 1045 257 Note: Dimensions may vary ± 10 mm. Use of vibration damers influences total height. G = Galvanised manifolds. X = AISI 316 Stainless steel manifolds.
Dimensions and weights ydro 0 G - X 3 ums Booster set with 3 ums CR 15 - CR - CR 32 - CR 45 - CR 64 - CR 90 Q Q L2 L A B1 B2 TM02 2126 31 L L2 3 CR 90-4-2 LQ A B1 B2 TM02 2184 31 Pum tye Connections B1 B2 Weight L L2 LQ A Q G X G X G X [kg] 3 CR 15-2 761 295 3 CR 15-3 16 8 7 3 CR 15-4 DN 942 344 3 CR 15-5 DN PN 10 987 359 10-766 766 986 986 1 1455 3 CR 15-6 1083 416 3 CR 15-7 18 1128 425 3 CR 15-8 DN 1235 434 3 CR -2 761 295 16 3 CR -3 897 341 DN 3 CR -4 993 416 DN PN 10 3 CR -5 10-766 766 986 986 1 1455 1038 413 3 CR -6 18 1088 428 3 CR -7 DN 1128 431 3 CR 32-2-2 9 511 3 CR 32-2 7 538 DN 1 3 CR 32-3 1096 565 DN 1 PN 10 3 CR 32-4 2116 10-956 856 1241 1141 165 1455 1166 589 3 CR 32-5 1419 712 3 CR 32-6 DN 1 1429 724 3 CR 45-1 990 562 3 CR 45-2-2 1089 576 3 CR 45-2 DN 0 DN 0 PN 10 2116 10-1073 1071 1413 1411 0 1455 1089 644 3 CR 45-3 1352 713 3 CR 45-4 1446 788 3 CR 64-2-2 1095 615 3 CR 64-2 DN 0 1278 724 3 CR 64-3-1 DN 0 PN 10 1374 838 2116 10-1091 1089 1431 1429 0 1455 3 CR 64-4-2 1457 877 3 CR 64-4 DN 0 1579 1036 3 CR 90-1 1022 616 3 CR 90-2-2 DN 0 1297 742 3 CR 90-2 DN 0 PN 10 2116-1311 841 10 1106 1106 1446 1444 0 1455 3 CR 90-3-2 13 883 3 CR 90-3 DN 0 1525 883 3 CR 90-4-2 10 826 1684 1291 Note: Dimensions may vary ± 10 mm. Use of vibration damers influences total height. G = Galvanised manifolds. X = AISI 316 Stainless steel manifolds. 31
Dimensions and weights ydro 0 G - X 4 ums Booster set with 4 ums CR 3 - CR 5 - CR 10 L2 L Q A B1 B2 TM02 21 31Booster set with 4 ums Pum tye Connections B1 B2 Weight L L2 A Q G X G X G X [kg] 4 CR 3-5 548 164 4 CR 3-6 566 168 4 CR 3-7 584 172 4 CR 3-8 G 2 G 2½ 1690 12 8 5 568 616 115 1455 646 176 4 CR 3-10 682 1 4 CR 3-12 718 188 4 CR 3-15 772 196 4 CR 5-5 637 164 4 CR 5-7 691 172 4 CR 5-8 718 1 4 CR 5-9 G 2½ G 2½ 1690 12 552 568 628 644 115 1455 811 184 4 CR 5-10 838 236 4 CR 5-13 919 236 4 CR 5-15 973 242 4 CR 10-3 673 2 4 CR 10-4 769 264 4 CR 10-5 799 262 DN 4 CR 10-6 829 268 DN PN 10 4 CR 10-7 17 10 632 676 832 876 145 1455 918 282 4 CR 10-8 948 286 4 CR 10-9 978 290 4 CR 10-10 DN 1045 344 Note: Dimensions may vary ± 10 mm. Use of vibration damers influences total height. G = Galvanised manifolds. X = AISI 316 Stainless steel manifolds. 32
Dimensions and weights ydro 0 G - X 4 ums Booster set with 4 ums CR 15 - CR - CR 32 - CR 45 - CR 64 - CR 90 A A Q Q L L2 LQ B1 B2 TM02 2127 31 4 CR 90-4-2 L L2 LQ B1 B2 TM02 2186 31 Pum tye Connections B1 B2 Weight L L2 LQ A Q G X G X G X [kg] 4 CR 15-2 761 381 4 CR 15-3 8 394 4 CR 15-4 DN 942 464 4 CR 15-5 DN PN 10 987 484 15 10 626 766 766 986 986 1 1455 4 CR 15-6 1083 5 4 CR 15-7 1128 572 4 CR 15-8 DN 1235 584 4 CR -2 761 381 4 CR -3 897 4 DN 4 CR -4 993 5 DN PN 10 4 CR -5 15 10 626 766 766 986 986 1 1455 1038 556 4 CR -6 1088 576 4 CR -7 DN 1128 5 4 CR 32-2-2 9 9 4 CR 32-2 7 745 DN 1 4 CR 32-3 1096 781 DN 1 PN 10 4 CR 32-4 1900 00 626 956 856 1241 1141 165 1455 1166 813 4 CR 32-5 1419 977 4 CR 32-6 DN 1 1429 993 4 CR 45-1 990 2 4 CR 45-2-2 1089 822 4 CR 45-2 DN 0 DN 0 PN 10 1900 00 626 1073 1071 1413 1411 0 1455 1089 912 4 CR 45-3 1352 4 4 CR 45-4 1446 1104 4 CR 64-2-2 1095 899 4 CR 64-2 DN 0 1278 1044 4 CR 64-3-1 DN 0 PN 10 1374 1196 1900 00 626 1091 1089 1431 1429 0 1455 4 CR 64-4-2 1457 1248 4 CR 64-4 DN 0 1579 14 4 CR 90-1 1022 900 4 CR 90-2-2 DN 0 1297 1068 4 CR 90-2 DN 0 PN 10 626 1455 1311 10 1900 00 1106 1104 1446 1444 0 4 CR 90-3-2 13 1256 4 CR 90-3 DN 0 1525 1256 4 CR 90-4-2 0 10 1648 10 Note: Dimensions may vary ± 10 mm. Use of vibration damers influences total height. G = Galvanised manifolds. X = AISI 316 Stainless steel manifolds. 33
Diahragm tank ydro 0 G-X Diahragm tank selection To ensure stable oeration, the ydro 0 G - X booster set must be installed in combination with an adequate diahragm tank. The size of the obligatory diahragm tank can be calculated by means of the followong formula: V = Tank volume [litres] Q = Mean flow [m 3 /h] = Difference between cut-in and cut-out ressure Cut-in = V = Q --------------------------------------------------------------------------------- 0 ( 1 + ( cut in) + ) -- 1 4 n k max Cut-in ressure (lowest) [bar] n max = Max. number of starts/stos er hour k = Constant for diahragm tank re-charge ressure: k = 0.9 The diahragm tank re-charge ressure is set to 0.9 times the lowest cut-in ressure. The diahram tank may also be selected on the basis of the below tables in which the following values have been used: Motors u to and including 3.0 kw: n = to Motors above 3.0 kw: n = 10 to Diff. between cut-in and cut-out: = 1.5 [bar] Grundfos ums and motors are not subject to any articular limitations as they are tested u to start/ stos er hour. owever when dimensioning the diahragm tank volume the following arameters may also be considered: maximum number of start/stos er hour allowed by local regulations maximum number of start/stos er hour described by the system designer temerature and ventilation conditions available sace for diahragm tank installation. Minimum diahragm tank volume [litres] at = 1.5 [bar] and n max = : Pum tye Cut-in 1 [bar] Cut-in 2 [bar] Cut-in 3 [bar] Minimum diahragm tank volume [litres] Cut-in 4 [bar] Cut-in 5 [bar] Minimum diahragm tank volume [litres] at = 1.5 [bar] and n max = : Refer to the cut-in ressure closest to the lowest setting of the selected booster set. Cut-in 6 [bar] Cut-in 7 [bar] CR 3 65 84 102 1 1 158 176 195 CR 5 108 135 1 0 232 263 294 324 CR 10 173 222 272 321 3 4 469 518 CR 15 346 444 543 642 741 839 938 1037 CR 432 556 679 2 926 1049 1173 1296 CR 32 691 889 1086 1284 1481 1679 1876 74 CR 45 972 12 1528 15 83 2361 2639 2916 CR 64 1383 1778 2173 2568 2963 3358 3753 4148 CR 90 1944 55 3611 4166 4722 5277 5833 Pum tye Cut-in 1 [bar] Cut-in 2 [bar] Cut-in 3 [bar] Minimum diahragm tank volume [litres] Cut-in 4 [bar] Cut-in 5 [bar] Cut-in 6 [bar] Cut-in 7 [bar] CR 3 25 36 42 47 53 59 CR 5 33 41 51 78 88 98 CR 10 52 67 81 96 111 126 141 156 CR 15 104 133 163 193 222 252 281 311 CR 1 167 4 241 278 315 352 389 CR 32 7 267 326 385 444 4 563 622 CR 45 292 375 458 542 625 8 792 875 CR 64 415 533 652 7 889 7 1126 1244 CR 90 583 7 917 1083 12 1417 1583 17 Cut-in 8 [bar] Cut-in 8 [bar] 34
Further roduct documentation In addition to the rinted data booklet, Grundfos offers the following sources of roduct documentation. WinCAPS WebCAPS. WinCAPS WinCAPS is a Windows-based Comuter-Aided Product Selection rogram containing information on more than 90,000 Grundfos roducts. Available on CD-ROM in more than 15 languages, WinCAPS offers detailed technical information selection of the otimum um solution dimensional drawings of each um detailed service documentation installation and oerating instructions wiring diagrams of each um. Fig. 7 WinCAPS CD-ROM cd-wincas Click on Catalogue and select a roduct from the extensive roduct catalogue. Click on Sizing and select the most suitable um for your alication. WinCAPS Fig. 8 WinCAPS 35
Further roduct documentation WebCAPS WebCAPS is a Web-based Comuter Aided-Product Selection rogram and a web-version of WinCAPS. Available on Grundfos homeage, www.grundfos.com, WebCAPS offers detailed technical information dimensional drawings of each um wiring diagrams of each um. Click Catalogue and select a roduct from the extensive roduct catalogue. Click Relacement and select the right relacement um based on the current installation. Click Literature to select and download Grundfos documentation by browsing the roduct ranges or erforming a secific search. The literature includes: - Data booklets - Installation and oerating instructions - Service instructions. Click Product search and select a roduct from the extensive roduct catalogue. Click Service to to find information on service kits and sare arts. If you are a registered user click Log in to: - save your settings - define and save your own units - save ersonalised information. Click Units and select your referred units of measurement: - Default units - SI units - US units. Click Language and select your referred language. WebCAPS Fig. 9 WebCAPS 36
37
38
39
Being resonsible is our foundation Thinking ahead makes it ossible Innovation is the essence V7127644 04 Rel. V7127644 02 GB Subject to alterations. GRUNDFOS A/S. DK-88 Bjerringbro. Denmark Telehone: +45 87 14 00. www.grundfos.com