ADA COMPLIANT READ CAREFULLY

9889 Garrymore Ln Missoula, MT 59808 888-687-3552 +1-406-549-0769 www.aquacreek.com Ambassador Pool Lift PART #: F-PPXRD-NA-01 US PATENT NUMBER: [D507,769 S] [7,249,386 B2] 350 LB. [160 kg] MAXIMUM WEIGHT CAPACITY MANDATORY LEAVE THIS MANUAL WITH LIFT OWNER Read and follow all instructions. Lift safety can only be ensured if the lift is installed and operated according to these instructions. NEVER permit children to play on or around the lift Do not allow children to use the lift without adult supervision NEVER apply direct water pressure to the electronics NEVER use the lift with a dry pool ADA COMPLIANT READ CAREFULLY Check entire box and all packing materials for parts. Before beginning assembly, read the instructions and identify parts using the figures and parts listed in this document. It is critical that all parts be carefully inspected prior to installation. If any damage occurred in transit, Aqua Creek Products, LLC must be notified within three days of receipt of unit. Proper installation cannot be overstressed, as an improper installation voids Aqua Creek s warranty and may affect the safety of the user. 1

Ambassador Lift Table of Contents PAGE DESCRIPTION PAGE DESCRIPTION 2 Ambassador Components 11 Basic Troubleshooting 3 ADA Installation Guidelines 12 Battery Test Cable Instructions 4-5 Anchor Installation: Core-Drill Retro-Fit 13 Proper Care of Pool & Spa Lifts 6-7 Anchor Installation: Saw-Cut Retro-Fit/ New Construction 14 Ambassador Parts List 8 Ambassador Lift Assembly Instructions 15 Seat & Actuator Assembly Parts List 9-10 Pull-out Legrest Instructions 16 Warranty Ambassador Components 1. AMBASSADOR LIFT MAIN ASSEMBLY 2. 24V VITO BATTERY 3. VITO BATTERY CHARGER 1 4 4. VITO HANDSET 5. SAFETY BELT 6. VITO BATTERY TEST CABLE 7. ANCHOR JIG PLATE & HARDWARE (IF ORDERED WITH ANCHOR) 5 7 3 2 6 2

ADA REQUIREMENTS: Installation: ADA Guidelines The Ambassador Lift is ADA Compliant. The installation must meet the following requirements: Clear deck space dimensions (see FIGURE 1) Lift installed between 22.5-38 inches from the pool edge Deck slope no greater than 1:48 The seat must submerge at least 18 inches into the water. The lift should be installed at a location with 42-48 inches of depth (deck to pool floor) Anchor setbacks are based on straight pool/spa walls. Curved pool/ spa walls will effect the anchor setback. 48" 57 1/2" ADA REQUIRED CLEAR-DECK SPACE (36" x 48") 12" 36" 64" CHAIR C L 16" (ADA REQ'D MIN.) *22 1/2" POOL WALL FIGURE 1 *NOTE: 22 1/2" IS THE MINIMUM SETBACK. 38" IS THE MAXIMUM LIFT SETBACK. 3

Anchor Installation: Core-Drill Retro-Fit NOTE: 2500PSI MINIMUM STRENGTH 6 THICK OR MORE CONCRETE IS REQUIRED You will need: Core drill and 1½ core drill bit Tape measure Marking pen Hammer Cold chisel Torpedo level 2-part construction epoxy* Masking tape Black electrical tape (optional) Anti-seize packet *Aqua Creek recommends either Hilti Brand HIT RE-500-SD or Simpson brand SET-XP or equivalent Anchor jig plate with hardware 1. Mark the 3 hole locations on your deck using the larger holes of the anchor jig plate as a template. For ADA compliance, confirm the center of the jig plate holes are 22.5 to 38 inches from the pool s edge. SEE FIGURE 1 ON PAGE 3 2. Drill the 3 hole locations to 4 1/2 inches deep using the 1 1/2 inch drill bit. Clear all debris and ensure holes are completely dry. NOTE: Create a depth marker on the drill bit with black electrical tape to make sure you drill to the right depth. NOTE: Local bonding regulations may require you to drill one hole larger than the others in order to bond at least one of the anchor inserts. You may need to saw cut a portion of your deck. See Saw Cutting Retro-Fit Instructions on page 6. 3. Remove the nuts and the black protective coverings from the threaded anchor inserts. 4. Thread the 1/2 inch hex bolts and flat washers through the smaller anchor jig plate holes and into the anchor inserts. Be sure to use anti-seize on the threads! Confirm the tops of the inserts are flush with the bottom of the plate. SEE FIGURE 2 ON PAGE 5 NOTE: We recommend using masking tape around the holes on the bottom of the anchor jig plate to help prevent the anchor plate from being accidentally epoxied to the pool deck. 4

Anchor Installation: Core-Drill Retro-Fit (CONTINUED) 5. Bond at least one of the anchor inserts according to your local code requirements. For more information see NEC Article 680.26. 6. Test fit the anchor assembly into the pre-drilled holes and use a torpedo level to ensure your anchoring system is level. SEE FIGURE 3 1/2" X 1-1/2" HEX BOLT (3) 1/2" FLAT WASHER (3) ANCHOR JIG-PLATE 7. Remove the anchor assembly and fill each hole halfway with 2-part construction epoxy (or equivalent). 8. Place the anchor assembly back into the holes. Wiggle the assembly as it s reinserted to ensure the epoxy fully coats the threads. P-7200ANB ANCHOR INSERT (3) 9. Once again, check that the anchor assembly is level and anchor inserts are flush with deck. FIGURE 2 10. Once the epoxy has set up, remove the hardware and the anchor jig plate. Your lift is now ready to be mounted to the anchoring system. The anchor jig plate may be recycled or used to install other anchors. *MIN AND MAX SETBACK DISTANCES ARE FOR TYPICAL FLAT POOL DECK APPLICATIONS. POOLS WITH A RAISED CURB OR IN GROUND SPAS WITH BENCHES CAN VARY. CHECK WITH AQUA CREEK FOR PROPER SETBACK DISTANCES AND ANCHOR LOCATIONS. LIFT OUTLINE 10" 10" 17 3/4" USE JIG-PLATE ASSEMBLY FOR TEST-FITTING AND TO HOLD ANCHORS IN PLACE AS EPOXY CURES *22 1/2" TO 38" SETBACK (4 3/4" MIN TO 20 1/4" MAX SETBACK) CORE DRILL 1-1/2" 4-1/2" DEEP, 3 PLACES POOL WALL (OR FURTHEST OBSTRUCTION) USE JIG-PLATE (LARGER HOLES) TO MARK LOCATIONS FIGURE 3 5

You Will Need: Concrete saw with diamond blade Tape measure 4 long straight edge or chalk line Sledge hammer Cold chisel Large adjustable wrench FIGURE 4 Anchor Installation: Saw-Cut Retro-Fit 1" X 4" ANCHOR INSERT (3) #10-24 X 3/4" CAP-SCREW Torpedo level String Line Concrete & concrete finishing tools #5 rebar NOTE: 2500PSI MINIMUM STRENGTH 6 THICK OR MORE CONCRETE IS REQUIRED 1. Remove one nut from each anchor insert. Place the anchor inserts through the larger hole of the anchor jig plate. Thread the removed nuts back onto the anchor inserts. The anchor plate should be sandwiched between the two nuts on each anchor insert. SEE FIGURE 4 51" 1" HEX NUT (6) Cu BONDING LUG ANCHOR JIG-PLATE #10-24 NYLOCK NUT 1/4" FLAT WASHER SIDE VIEW (ASSEMBLED) 1/4" X 3/4" PAN-HEAD 51" BONDING LUG 22 1/2" MIN TO 38" MAX LABEL 12" TYP 2. Mark out a section of the pool deck that you are removing. Plan on removing at least 4 feet 3 inches by 4 feet 3 inches. 3. Cut along your marks with a diamond blade concrete saw. 4. Using the sledge hammer break up the concrete within the cut area and remove the pieces. 5. Install rebar in the open area of the deck. Tie the rebar into the existing deck if possible. SEE FIGURE 5 8-AWG SOLID- COPPER WIRE (ATTACH TO BONDING-GRID) 6. Set the anchor system in place. For ADA compliance and clearance, make sure the center of the large anchor jig plate hole is between 22.5 and 38 inches from the pool s edge. SEE FIGURE 5 7. Using the string line or a straight edge & level, confirm the top of each anchor body is level with the FINISHED deck surface. Each anchor body can be individually adjusted by turning the nuts with a large wrench. 6" FLUSH W/ DECK 2500 PSI MIN. 4" #5 REBAR DRILL & EPOXY INTO EXISTING SLAB (4" MIN EMBED) POOL WALL OR FURTHEST OBSTRUCTION #5 REBAR E-W (5 PCS) *SETBACK DIMENSIONS ARE FOR FLAT DECK APPLICATIONS. FOR SLOPED DECKS OR OTHER FEATURES, CONTACT AQUA CREEK BEFORE INSTALLATION. FIGURE 5 8. Bond the anchoring system according to your local code requirements by using the bonding lug on the anchor plate. SEE FIGURE 5 (See NEC Article 680.26) 9. Pour concrete and finish the pool deck surface. 10. Once the concrete has cured, the lift is ready to be mounted to the anchoring system. 6

You will need: Tape measure Marking pen Torpedo level Large adjustable wrench Concrete & concrete finishing tools #5 rebar 51" 10" 10" Anchor Installation: New Construction 51" NOTE: For installations where a new deck is being poured, or where a dedicated pad is being poured just for the pool lift, the concrete must satisfy the ADA requirements outlined on page 3 of this manual. Your pool deck must be at least 4 feet - 3 inches long by 4 feet - 3 inches wide by 6 inches thick. It must be reinforced with 5 sticks of #5 rebar each way, 2 inches clear (min) from the top and bottom of the footing. POOL DECK 1. Remove one nut from each anchor insert. Place the anchor inserts through the larger hole of the anchor jig plate. Thread the removed nuts back onto the anchor inserts. The anchor plate should be sandwiched between the two nuts on each anchor insert. SEE FIGURE 4, PAGE 6 2. Install rebar in the open area of the deck. SEE FIGURE 5, PAGE 6 *SETBACK DISTANCES ARE FOR FLAT DECKS. IF YOUR DECK IS SLOPPED, CONTACT AQUA CREEK BEFORE INSTALLATION. *22 1/2" MIN TO 38" MAX 3. Set the anchor system in place. For ADA compliance and clearance, make sure the center of the large anchor jig plate holes are between 22.5 and 38 inches from the pool s edge. SEE FIGURE 6 2500PSI MIN 6" #5 REBAR FIGURE 6 29" 22" *22 1/2" MIN TO 38" MAX FLORIDA "GATOR HAUNCH" 4. Using the string line or a straight edge & level, confirm the top of each anchor body is level with the FINISHED deck surface. Each anchor body can be individually adjusted by turning the nuts with a large wrench. 5. Bond the anchoring system by using the bonding lug on the anchor jig plate. Bond the system according to your local code requirements. (See NEC Article 680.26) SEE FIGURE 5, PAGE 6 6. Pour your concrete and finish the pool deck surface. 7. Once the concrete has cured the lift is ready to be mounted to the anchoring system. 7

Ambassador Assembly Instructions 1. Attach seat belt to the seat. SEE FIGURE 7 LOOP ON TOP FOR EASY ACCESS 2. Install the Ambassador pool lift onto the three (3) anchors using the supplied 1/2 inch x 1 1/2 inches stainless steel hex-head bolts and 1/2 inch stainless steel flat washers. Make sure all bolts are tight before using the lift. SEE FIGURE 8 3. Before installing the battery, place it on the charging unit and let it charge for 24 hours. Make sure the orange charge light illuminates when the battery is being charged. FIGURE 7 THREAD THROUGH SLOTS AND PINCH TOGETHER TO HOLD 4. Remove the fully charged battery from the charger, grease the terminals, and install it on top of the control box. The battery will line up with the control box, and will click when it properly locks in place. The lift will only operate when the battery is correctly mounted. WHEN NOT IN USE, STORE THE BATTERY ON THE CHARGER! ATTACH FULLY-CHARGED BATTERY HANDSET PLUGS INTO CONTROL BOX CONTROL BOX 1/2" X 1-1/2" HEX BOLT (4) 1/2" FLAT WASHER (4) POOL WALL ANCHORS (3) INSTALLED FLUSH W/DECK SURFACE FIGURE 8 8

Pull-out Legrest Installation Instructions The PULL-OUT LEGREST ASSEMBLY is designed to fit under the standard Aqua Creek chair, and is installed inside the 2 square tubing that supports the chair from underneath. Installation is the same for every lift, Ranger lift is shown in picture below. To install the pull-out leg-rest; 1. With a flat-blade screwdriver, pry off the 2 square plug from the end of the 2 square tube of the seat arm. SEE FIGURE 9. 2. Drill a 9/32 hole at the location indicated in FIGURE 10 through the bottom of the chair support tube. Drill only through the bottom of the tube. Remove the burrs from the hole before installing the legrest assembly. SEAT SEAT ARM 2" SQUARE PLUG FIGURE 9 DRILL 9/32" (THIS SIDE) 3/4" CHAIR SUPPORT TUBE (BOTTOM VIEW) 1" DRILL 9/32" HOLE (BOTTOM OF CHAIR SUPPORT TUBE) (SEE DRAWING TO THE RIGHT) FIGURE 10 9

Pull-out Legrest Installation Instructions You Will Need: 3. Orient the pull-out legrest as shown in FIGURE 11 and slide the Flat head Screwdriver Hammer / Mallet PLASTIC GUIDE/SPACER into the chair support tube. Tap the PLASTIC 5/32 Allen Wrench GUIDE/SPACER with a hammer or mallet until flush with the end of the support tube. The threaded hole in the bottom of the PLASTIC GUIDE/SPACER should line-up with the hole drilled in the chair support tube. Install the lock washer and 1/4-20 x 1/2 inch cap screw from underneath and tighten until snug. 1" SQ. TUBE PLASTIC GUIDE/SPACER 1/4" LOCK WASHER, SS 1/4-20 X 1/2" CAP SCREW, SS CHAIR SUPPORT TUBE PULL-OUT LEGREST PLASTIC GUIDE/SPACER FLUSH WITH 2" SQ. TUBE FIGURE 11 The PULL-OUT LEGREST is now ready to use. However, before using, slide the legrest in and out, and put the pad up and down to make sure everything works smoothly. LEGREST STOWED PULL LEGREST OUT FLIP LEGREST UP AND PIN SLIDE FORWARD AND INSERT PIN TO LOCK IN "UP" POSITION SLOT PIN 10

Problem: The lift won t move. Solution: 1. Make sure the cords are properly plugged in: Basic Troubleshooting Check the ends of the cords for corrosion or damage. The cord plugs should be recessed into the outlet. You should feel them pop into place when they are correctly inserted. NOT Properly Inserted: The cord plug is flush with or sticking out of the outlet Properly Inserted: The cord plug is recessed into the outlet 2. Check the contact points: 3. Make sure the battery is fully charged: The Charger is ON when the green light is glowing Make sure the contact point of the control box and the battery are not damaged or corroded. If there is corrosion clean with Scotch-Brite TM pad. Put some dielectric grease on the contact points before reattaching the battery. The Battery is CHARGING when the orange light is glowing When the Battery is fully charged the orange light will stop glowing Problem: The lift stopped moving and is stuck. Solution: 1. Press the Emergency button For troubleshooting videos Visit: www.aquacreek.com or scan the QR Code below using your smartphone. Press the emergency retract button on the front of the control box to retract the lift. Note: the lift will not retract if the battery is not fully charged or if the control box is not working. The emergency button only overrides the remote handset. Note: If you feel your lift is malfunctioning due to a faulty battery or connections, contact Aqua Creek Products for a testing kit. 11

Battery Test Cable Instructions WARNING! DO NOT ATTEMPT TO DIRECTLY PROBE THE BATTERY CONNECTOR TO TEST VOLTAGE. THIS MAY CAUSE PERMANENT DAMAGE TO THE BATTERY! USE THE SUPPLIED BATTERY TEST CABLE ONLY FOR CHECKING THE BATTERY VOLTAGE! The Aqua Creek 24V battery has a cable and connector for connecting to the control box or to the battery charger. The battery connector is not suitable to check the battery voltage, as it is very hard to probe the connector without shorting-out the battery, which will cause damage. For this reason, a separate battery test cable is provided. To safely check the battery voltage, use a voltmeter or multimeter with standard test probes, and insert the probes into the test cable as shown below. 24V BATTERY BATTERY CONNECTOR MALE CONNECTOR BATTERY TEST CABLE INSERT TEST PROBES TO CHECK VOLTAGE 12

Proper Care of Pool & Spa Lifts PROCEDURE DAILY WEEKLY MONTHLY Wash down lift with fresh water and dry with clean, soft, non-abrasive cloth. Recharge battery. Run the lift through a complete test cycle to verify it is functioning properly. Visually inspect lift for damage, corrosion, and loose or missing hardware. Check all contact points for damage and/or corrosion. Repair, clean, and apply dielectric grease to all contact points. Thoroughly clean lift frame and apply a liberal coat of car wax to maintain the lift s finish. Check all Warning and Cautionary labels to make sure they are not faded or worn. Replace as needed. PROPER CARE NOTES Use only fresh water to wash your lift. Do not wash with pool water. Use only clean, soft, non-abrasive cloths to wipe down your lift. Do not store lift in pump room or near chemicals. Do not allow children to play on or around this lift. When cleaning the lift, do not spray water directly on control box or battery. The lift may need to be bonded according to local code requirements. STAIN REMOVAL TIPS: To remove stubborn stains from finish, spray affected area with mild dish soap, rub briskly with a 3M Scotch Brite pad. Use white epoxy paint to touch up the finish. Apply wax to protect when dry. For service and/or replacement parts contact Aqua Creek direct at Toll free: (888) 687-3552 13

10 11 7 11 12 Ambassador Parts List 3 2 25 4 22 21 20 23 5 14 15 6 8 9 19 16 24 25 16 19 18 1 12 11 18 17 13 21 23 14 15 ITEM # QTY PART # DESCRIPTION 1 1 STL-100-11 BASE ASSEMBLY 2 1 STL-200-00 3 1 A-2012ARM-STL 4 1 A-2012SRS2 MAIN FRAME ASSEMBLY CHAIR ARM ASSEMBLY SEAT SUPPORT ASSEMBLY 5 1 L-2014FBL-STL CONTROL ARM 6 1 UHF-XR-02 ACTUATOR ASSEMBLY 7 1 SA-0904CA-A 18 CHAIR ASSEMBLY 8 1 F-105LAR FOOTREST ASSEMBLY 9 2 BHW 1/4 X 3/4 10 1 BH 5/16 X 4-1/2 11 3 WF 5/16 12 2 NN 5/16 13 1 BS 3/8 X 1-3/4 18-8 BOLT, 316 SS, 1/4-20 X 3/4 HWH BOLT, 316 SS, 5/16-18 X 4 1/2 HCS WASHER, FLAT, 5/16, 316 SS NUT, 316 SS, NYLOCK, 5/16-18 BOLT, 18-8 SS, 3/8 X 1 3/4 SHOULDER, 5/16-18 THREAD ITEM # QTY PART # DESCRIPTION 14 2 WF 1/2 WASHER, FLAT, 1/2, 316 SS 15 2 NN 1/2 16 2 BH 5/8 X 1-1/2 17 1 BH 5/8 X 5-7/8 18-8 NUT, 316 SS, NYLOCK, 1/2-13 BOLT, 316 SS, 5/8-11 X 1 1/2 HCS BOLT, 18-8 SS, 5/8-11 X 5 7/8 HCS, CUSTOM 18 2 WF 5/8 WASHER, FLAT, 5/8, 316 SS 19 3 NN 5/8 20 1 NN 3/4 21 2 22 1 THRUST WASHER, 1/2, BRONZE THRUST WASHER, 3/4, BRONZE 23 2 BRB FL-50-3 24 1 F-45ACB-C 25 2 PPB-CCB-10 NUT, 316 SS, NYLOCK, 5/8-11 NUT, 316 SS, NYLOCK, 3/4-10 WASHER, BRONZE, 1/2, TT-1001-1 WASHER, BRONZE, 3/4, TT-1205-1 BUSHING, BRONZE FLANGE, 1/2 X 5/8 X 3/8 X 1/8 COVER, ACTUATOR, WATER RESISTANT BOLT, 316 SS, 1/2 X 1 3/4 FHSCS, CUSTOM 14

Seat Assembly Parts List ITEM # QTY PART # DESCRIPTION 1 1 P-901 CHAIR, PLASTIC, 18 BLUE 5 3 8 6 2 2 P-2100FLA-38 CHAIR II ARMREST TUBE 3 1 P-1208HSB BRACKET, PLASTIC, HANDSET BRACKET 7 4 2 RUBBER HAND GRIPS GRIP, RUBBER HAND GRIP 5 2 SFL 12 X 3/4 SCREW, 316 SS, #12 X 3/4, FHSMS 6 4 WF 1/4 WASHER, FLAT, 1/4, 316 SS 7 2 BB 1/4 X 3-1/4 BOLT, 316 SS, 1/4-20 X 3 1/4 BHSCS 8 2 NN 1/4 NUT, 316 SS, NYLOCK, 1/4-20 9 1 COTTER PIN, 1/4 X 3 1/4 PIN, COTTERLESS PIN, 18-8 SS, 1/4 X 3 3/4 4 2 10 1 LANYARD LANYARD, FOR FOOTREST PIN, SS 11 1 SPH 10 X 3/4 SCREW, 316 SS, #10 X 3/4, PHSMS 1 12 1 F-38SB SEAT BELT, 2 WIDE BLACK W/VELCRO 4 2 12 9 10 11 Actuator Assembly Parts List 4 3 10 Item # QTY PART # DESCRIPTION 1 1 UHF-101-02 UNIVERSAL H-FRAME 11 1 2 1 UHF-104-01 H-FRAME BRACKET 3 1 9452K205 O-RING 4 1 340643-00 LINKA ACTUATOR, LA-34 5 1 GT10 (CONTROL BRACKET) MOUNTING BRACKET 7 9 5 8 6 1 VCB-LA8 SINGLE PORT CONTROL BOX 7 1 VCP100-29800 24V BATTERY 8 4 BHW 1/4 X 3/8 1/4-20 X 3/8 HEX WASHER HEAD 9 2 BSH 10 X 3/8 #10-24 X 3/8 SOCKET HEAD 10 1 BH 3/8 X 1 3/4 3/8-16 X 1 3/4 HEX BOLT 11 1 NN 3/8 3/8-16 NYLOCK NUT 12 1 M5 LPCS CONTROL BOX SCREW 8 6 9 12 2 15

Revised_9.14.2017 AQUA CREEK PRODUCTS, LLC LIMITED FIVE (5) YEAR WARRANTY: AMBASSADOR LIFT (ITEM # s F-PPXRD-NA, F-PPXRD-R) Aqua Creek Products, LLC (a.k.a. Aqua Creek) warrants to the original end user purchaser that products manufactured by Aqua Creek, when properly installed in accordance with assembly and installation instructions, and properly used and maintained, shall be free from defects in material and workmanship for a period of five (5) years from the date of original purchase, provided that Aqua Creek receives prompt notice in writing of any defect or failure and satisfactory proof thereof, with the following exception(s): Exceptions: All electrical components, including the linear actuator shall have the following warranty period: o Year 1-2: 100% Coverage o Year 3: 60% Coverage (Customer is responsible for 40% of replacement cost) o Year 4: 50% Coverage (Customer is responsible for 50% of replacement cost) o Year 5: 40% Coverage (Customer is responsible for 60% of replacement cost) Hydraulic actuators and mesh slings shall have a warranty period of one (1) year from the date of original purchase. Powder coat finish scratches, scrapes, corrosion, or dents from customers normal use, negligence, or abuse This warranty specifically excludes reimbursement for labor to remove, repair, or install the product and any shipping charges. These warranties do not cover any damages due to accident, force majeure, act of nature, misuse, abuse, negligence or failure to properly maintain any products, or normal wear and tear from day to day operations. In the event that any products are altered, repaired, or improperly installed or improperly used by anyone without the prior written approval by Aqua Creek, all warranties are void. IMPORTANT: AMOUNT OF WEIGHT PLACED ON LIFT SHALL NOT EXCEED THE RATED LIFTING CAPACITY FOR THE LIFT. NEVER OPERATE THE LIFT UNDER LOAD IN A DRY POOL (WITH NO WATER IN THE POOL). It is the responsibility of the lift owner to verify the weight of the patron for warranty claim purposes and to ensure that the lift is not overloaded. Non-payment for product to Aqua Creek may void warranty. To initiate a warranty claim, the owner of an Aqua Creek product must provide the place of purchase, in writing, with a full description of the product, its serial number, the dates of purchase and installation, and the exact nature of the defect. Within thirty (30) days after receipt of a written warranty claim by Aqua Creek, and barring any unforeseen delays, the place of purchase will be notified of Aqua Creek s decision regarding the claim. If requested by Aqua Creek, any defective product must be returned, freight prepaid by customer, to Aqua Creek s designated factory location or duly appointed distributor for inspection and/or repair. Aqua Creek will, at its option, repair or replace the failed or defective item, and deliver the repaired product or replacement to the customer. All freight charges are the responsibility of the customer. Products returned to Aqua Creek for which Aqua Creek provides replacement under this limited warranty shall become the property of Aqua Creek. A new warranty period shall NOT be established for the repaired or replaced products. Such products shall remain under warranty only for the remainder of the original warranty period on the original products purchased. This written limited warranty constitutes the final, complete and exclusive statement of warranty terms. No person or organization is authorized to make any other specific or implied warranties or representations on behalf of Aqua Creek. THE WARRANTIES SET FORTH HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, WHICH ARE HEREBY DISCLAIMED AND EXCLUDED, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE. THE SOLE AND EXCLUSIVE REMEDIES FOR BREACH OF ANY AND ALL WARRANTIES WITH RESPECT TO THE PRODUCTS SHALL BE LIMITED TO REPAIR OR REPLACEMENT AT AQUA CREEK S DESIGNATED FACTORY LOCATION, OR DULY APPOINTED DISTRIBUTOR, OR IN PLACE AT AQUA CREEK S OPTION. IN NO EVENT SHALL AQUA CREEK S LIABILITY EXCEED THE ENTIRE AMOUNT PAID TO AQUA CREEK BY THE ORIGINAL PURCHASER FOR THE FAILED OR DEFECTIVE PRODUCT. IN NO EVENT SHALL AQUA CREEK PRODUCTS, LLC BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, INDIRECT, PUNITIVE OR EXEMPLARY DAMAGES OR LOST PROFITS FROM ANY BREACH OF THIS LIMITED WARRANTY OR OTHERWISE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, SO SOME OF THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. Aqua Creek Products, LLC 9889 Garrymore Lane Missoula, MT 59808 Toll Free: (888) 687-3552 Local/Intnl: (406) 549-0769 www.aquacreek.com 16

+1-406-549-0769 888-687-3552 PRO-POOL SERIES ACCESSORIES COVER F-120PPC F-45ACB-C Pro Pool, Ranger, Ambassador, Patriot, Portable Pro Pool Lift Cover - Ranger/ Pro Pool/ Ambassador/ Patriot/ Portable Pro Pool Actuator Cover - Ranger/ Pro Pool/ Patriot/ Ambassador/ Portable Pro Pool SOLAR CHARGERS F-043SCH F-044SCH Patriot Pro Pool/ Ambassador/ Ranger sales@aquacreek.com www.aquacreek.com ACCESSORIES & OPTIONS F-423CS F-019CA F-422PLH-2 F105LAR F-38SB F-ASAPRL UPGRADE PACKS F-004PLBAP F-004PLBAPV F-950SAPV F-12PPAP Chest Strap Cycle Attachment Headrest (all other lifts) Pull-Out Legrest Seat Belt, Standard Seat Pole Option Adjustable Height (Ranger only) TRANSPORT CARTS F-428HT F-914STC Transport Cart w/linak Controls - Pro Pool Transport Cart w/vito Controls - Ranger Transport Cart - Ambassador Patriot/ Pro Pool Ranger/ Pro Pool Ambassador UPGRADE PACKS INCLUDE** Lift Cover Extra Battery Headrest Chest Strap