Section 8
8-0
8-1 Section 8 1. Introduction To order parts, call the Nordson Customer Service Center at 800-241-8777 or your local Nordson representative. Use this five-column parts list, and the accompanying illustration, to describe and locate parts correctly. Using the Illustrated List Numbers in the Item column correspond to numbers that identify parts in illustrations following each parts list. The code NS (not shown) indicates that a listed part is not illustrated. A dash (-) is used when the part number applies to all parts in the illustration. The six-digit number in the Part column is the Nordson Corporation part number. A dash in this column ( ) means the part cannot be ordered separately or refers you to the appropriate parts list. The Description column gives the part name, as well as its dimensions and other characteristics when appropriate. Indentions show the relationships between assemblies, subassemblies, and parts. Item Part Description Quantity Note - 000 000 Assembly 1 1 000 000 S Subassembly 2 A 2 000 000 S S Part 1 S S S If you order the assembly, items 1 and 2 will be included. If you order item 1, item 2 will be included. If you order item 2, you will receive item 2 only. The number in the Quantity column is the quantity required per unit, assembly, or subassembly. The code AR (As Required) is used if the part number is a bulk item ordered in quantities or if the quantity per assembly depends on the product version or model. Letters in the Note column refer to notes at the end of each parts list. Notes contain important information about usage and ordering. Special attention should be given to notes.
8-2 2. AD-31 Swirl Handgun (RTD Style), Models SCR and STR* List Item Part Description Qty Note 01 102 406 Retainer, Nozzle, Hexagonal, Swirl Gun 1 02 Plate, Nozzle A 03 105 708 Body, Nozzle, Clamping (Seat) 1 B 04 945 032 O-Ring, Viton, 3 / 8 in. 1 C 05 107 206 Manifold with Tube Assembly 1 06 271 877 Cartridge, Packing, AD-31 1 07 101 887 Clamp, Tube, 0.228 in. 2 08 101 080 Body, Gun, with Interior Groove 1 D 08 102 150 Body, Gun, AD-31 1 E 09 324 268 Tubing, 1 / 8 in. Tygothane 10 984 120 Nut, Hexagonal, No. 10-32, Steel, Zinc-Plated 1 11 271 616 Linkage, Trigger 1 12 271 617 Spring, Compression, 0.620 in. x 0.455 in. Outer Diameter x 0.039 in. 1 13 985 216 Pin, Dowel, 0.250 in. x 1.250 in. 1 14 324 260 Valve, Handgun, No Bleed 1 15 983 526 Washer, Lock, Exterior, Split, No. 4, Steel, Zinc-Plated 2 16 981 759 Screw, Pan, 4-40 x 0.312 in., Steel, Black Oxide 2 17 981 817 Screw, Shoulder, 10-24 x 0.375 in. 1 B 18 271 626 Plate, Bearing 1 19 271 618 Trigger, Gun, AD-31 1 NOTE A: Nozzle plates must be ordered separately. Refer to the list of swirl nozzle plates. B: Apply a threadlocking adhesive. C: Apply Never-Seeze lubricant (P/N 900 341) or equivalent. D: Used with handgun P/N 101 207. E: Used with handgun P/N 101 206. * listed only for AD-31 handgun models AD-31 SCR (P/N 101 207) and AD-31 STR (P/N 101 206) Continued on next page
8-3 2. AD-31 Swirl Handgun (RTD Style), Models SCR and STR* List (contd.) Item Part Description Qty Note 20 939 994 Block, Terminal, 1-Station 4 E 21 939 320 Block, Terminal, 3-Station 2 D 22 274 733 Sensor, Resistance Temperature Detector 1 23 986 305 Clip, Wire Retaining 1 24 274 708 Sleeve, Pivot 1 25 981 735 Screw, Fillister, 6-32 x 0.500 in. with Poly-Lok 11 26 105 491 Kit, Pivot Sleeve 1 D 26 105 489 Kit, Pivot Sleeve 1 E --- S Shell, Pivot Sleeve 2 G 981 735 S Screw, Fillister, 6-32 x 0.500 in. with Poly-Lok 4 G 274 345 S Tag, Warning, AD-31 Gun 1 G 981 800 S Screw, Drive, RD, 0 in. x 0.125 in., Zinc 4 G 27 986 322 Retaining Ring, RD, Sect. 5 / 8 in. Inner Diameter 1 28 940 121 O-Ring, Viton, 0.375 in. x 0.500 in. x 0.063 in. 1 D, F 28 940 101 O-Ring, Viton, 0.250 in. x 0.375 in. x 0.063 in. 1 E, F 29 954 012 Back-Up Ring, Single, 3 / 8 in. x 1 / 2 in. 1 D 29 954 036 Back-Up Ring, Single, 1 / 4 in. x 3 / 8 in. 1 E 30 272 404 Bearing, Thrust, With Grease 1 31 986 016 Retaining Ring, 5 / 8 in. Exterior, Heavy Duty 1 32 271 631 Spring, Conical 1 33 983 111 Washer, Lock, English, Split, No. 8, Steel, Zinc-Plated 2 34 981 080 Screw, Fillister, 8-32 x 1.250 in., Steel, Zinc-Plated 2 35 271 688 Connector, Swivel, 5 / 16 in. Hose 1 D 35 272 791 Connector, Swivel 1 E 36 938 130 Heater, Cartridge, 0.375 in. Diameter, 1.00 in. Length, 1 80 Watt, 240 Volt 37 981 073 Screw, Fillister, 8-32 x 0.375 in., Steel, Zinc-Plated 1 38 271 615 Sleeve, Bearing 1 F NOTE D:Used with handgun P/N 101 207. E: Used with handgun P/N 101 206. F: Apply a high-temperature grease (such as silicone lubricating grease, P/N 900 301) that is capable of withstanding 250 C (500 F). G: Available only as part of a kit. See item 26. * listed only for AD-31 handgun models AD-31 SCR (P/N 101 207) and AD-31 STR (P/N 101 206) Continued on next page
8-4 2. AD-31 Swirl Handgun (RTD Style), Models SCR and STR* List (contd.) Item Part Description Qty Note 39 271 619 Safety, Gun 1 40 271 620 Spring, Wave, Safety 1 41 274 383 Shell, Gun, Right, Bulk Melter 1 42 274 384 Shell, Gun, Left, Bulk Melter 1 Screw, Drive, RD, 0 x 0.125 in., Zinc 4 G 44 Tag, Hot Surface 1 G 44 Tag, Warning, AD-31 1 G 44 Tag, Information, AD-31 1 G 45 Tag Set, Guns 1 46 983 102 Washer, Lock, English, Split, No. 6, Steel, Zinc-Plated 1 NOTE G: Available only as part of a kit. See item 26. * listed only for AD-31 handgun models AD-31 SCR (P/N 101 207) and AD-31 STR (P/N 101 206)
8-5 1 2 3 4 5 7 9 41 39 40 25 6 8 10 44 11 12 13 38 16 14 45 44 19 15 25 37 46 20 18 21 17 22 23 24 42 21 20 27 28 29 26 25 36 30 31 44 32 20 25 35 33 33 26 34 4203077 Fig. 8-1 AD-31 Swirl Handgun (RTD Style), Models SCR and STR
8-6 3. AD-31 Swirl Handgun (Thermostat Style) Models SW, SWD, and SWE* List Item Part Description Qty Note 01 102 406 Retainer, Nozzle, Hexagonal, Swirl Gun 1 02 Nozzle, Plate A 03 105 708 Body, Nozzle, Clamping (Seat) 1 B 04 945 032 O-Ring, Viton, 3 / 8 in. 1 C 05 107 206 Manifold with Tube Assembly 1 06 271 877 Cartridge, Packing, AD-31 1 07 101 887 Clamp, Tube, 0.228 in. 2 08 102 150 Body, Gun, AD-31 1 09 324 268 Tubing, 1 / 8 in. Tygothane 10 984 120 Nut, Hexagonal, No. 10-32, Steel, Zinc-Plated 1 11 271 616 Linkage, Trigger 1 12 271 617 Spring, Compression, 0.620 in. x 0.455 in. Outer Diameter x 0.039 in. 1 13 985 216 Pin, Dowel, 0.250 in. x 1.250 in. 1 14 324 260 Valve, Handgun, No Bleed 1 15 983 526 Washer, Lock, Exterior, Split, No. 4, Steel, Zinc-Plated 2 16 981 759 Screw, Pan, 4-40 x 0.312 in., Steel, Black Oxide 2 17 981 817 Screw, Shoulder, 10-24 x 0.375 in. 1 B 18 271 626 Plate, Bearing 1 19 271 618 Trigger, Gun, AD-31 1 20 939 320 Block, Terminal, 3-Station 1 21 271 625 Heater, Cartridge, 0.38 in. Diameter, 1.00 in. Length, 60 Watt, 230 Volt 21 274 094 Heater, Cartridge, 0.38 in. Diameter, 1.00 in. Length, 65 Watt, 120 Volt 1 D, E 1 F 22 986 305 Clip, Wire Retaining 1 NOTE A: Nozzle plates must be ordered separately. Refer to the list of swirl nozzle plates. B: Apply Never-Seeze lubricant (P/N 900 341) or equivalent. C: Apply a threadlocking adhesive. D: Used with handgun model SW P/N 101 209. E: Used with handgun model SWD P/N 101 208. F: Used with handgun model SWE P/N 101 210. * listed only for AD-31 handgun model SW (P/N 101 209), model SWD (P/N 101 208), and model SWE (P/N 101 210). Continued on next page
8-7 3. AD-31 Swirl Handgun (Thermostat Style) Models SW, SWD, and SWE* List (contd.) Item Part Description Qty Note 23 274 708 Sleeve, Pivot 1 24 981 735 Screw, Fillister, 6-32 x 0.500 in. with Poly-Lok 11 25 105 481 Kit, Pivot Sleeve 1 D 25 105 493 Kit, Pivot Sleeve 1 E 25 105 487 Kit, Pivot Sleeve 1 F --- S Shell, Pivot Sleeve 2 H 981 735 S Screw, Fillister, 6-32 x 0.500 in. with Poly-Lok 4 H 274 345 S Tag, Warning, AD-31 Gun 1 H 981 800 S Screw, Drive, RD, 0 in. x 0.125 in., Zinc 4 H 26 986 322 Retaining Ring, RD, Sect. 5 / 8 in. Inner Diameter 1 27 940 101 O-Ring, Viton, 0.250 in. x 0.375 in. x 0.063 in. 1 28 954 036 Back-Up Ring, Single, 1 / 4 in. x 3 / 8 in. 1 29 272 404 Bearing, Thrust, With Grease 1 30 986 016 Retaining Ring, 5 / 8 in. Exterior, Heavy Duty 1 G 31 271 631 Spring, Conical 1 32 983 111 Washer, Lock, English, Split, No. 8, Steel, Zinc-Plated 2 33 981 080 Screw, Fillister, 8-32 x 1.250 in., Steel, Zinc-Plated 2 34 271 632 Connector, Swivel 1 D 34 272 791 Connector, Swivel 1 E 34 274 084 Connector, Swivel, 5 / 8 in.-18 1 F 35 981 000 Screw, Fillister, 5-40 x 0.250 in., Steel, Zinc-Plated 2 36 937 257 Thermostat, AD-31, 375 F 1 37 981 011 Screw, Fillister, 6-32 x 0.250 in., Steel, Zinc-Plated 1 38 271 615 Sleeve, Bearing 1 G 39 271 619 Safety, Gun 1 40 271 620 Spring, Wave, Safety 1 NOTE D: Used with handgun model SW P/N 101 209. E: Used with handgun model SWD P/N 101 208. F: Used with handgun model SWE P/N 101 210. G: Apply a high-temperature grease (such as silicone lubricating grease, P/N 900 301) that is capable of withstanding 250 C (500 F). H: Available only as part of a kit. See item 25. * listed only for AD-31 Handgun Models AD-31 SW (P/N 101 209), AD-31 SWD (P/N 101 208), and AD-31 SWE (P/N 101 210). Continued on next page
8-8 3. AD-31 Swirl Handgun (Thermostat Style) Models SW, SWD, and SWE* List (contd.) Item Part Description Qty Note 41 274 383 Shell, Gun, Right, Bulk Melter 1 42 274 384 Shell, Gun, Left, Bulk Melter 1 Screw, Drive, RD, 0 x 0.125 in., Zinc 4 H 44 Tag, Hot Surface 1 H 44 Tag, Warning, AD-31 1 H 44 Tag, Information, AD-31 1 H 45 Tag Set, Guns 1 46 983 102 Washer, Lock, English, Split, No. 6, Steel, Zinc-Plated 1 NOTE H: Available only as part of a kit. See item 25. * listed only for AD-31 Handgun Models AD-31 SW (P/N 101 209), AD-31 SWD (P/N 101 208), and AD-31 SWE (P/N 101 210).
8-9 1 2 3 4 5 7 9 41 39 40 24 6 8 10 44 11 12 13 38 16 14 45 44 19 15 24 37 46 18 20 17 21 22 23 42 35 36 26 27 28 25 24 29 30 44 31 20 24 34 32 32 26 33 4203087 Fig. 8-2 AD-31 Swirl Handgun (Thermostat Style), Models SW, SWD, and SWE
8-10 4. AD-31 Wide-Pattern Swirl Handgun (RTD Style), Models SCR-WP and STR-WP* List Item Part Description Qty Note 01 102 406 Retainer, Nozzle, Hexagonal, Swirl Gun 1 A 02 Nozzle B 03 137 229 Body, Nozzle, Clamping (Seat) 1 C 04 945 032 O-Ring, Viton, 3 / 8 in. 1 D 05 137 225 Manifold with Tube Assembly 1 06 271 877 Cartridge, Packing, AD-31 1 07 101 887 Clamp, Tube, 0.228 in. 2 08 101 080 Body, Gun, with Interior Groove 1 E 08 102 150 Body, Gun, AD-31 1 F 09 324 268 Tubing, 1 / 8 in. Tygothane 10 984 120 Nut, Hexagonal, No. 10-32, Steel, Zinc-Plated 1 11 271 616 Linkage, Trigger 1 12 271 617 Spring, Compression, 0.620 in. x 0.455 in. Outer Diameter x 0.039 in. 1 13 985 216 Pin, Dowel, 0.250 in. x 1.250 in. 1 14 324 260 Valve, Handgun, No Bleed 1 15 983 526 Washer, Lock, Exterior, Split, No. 4, Steel, Zinc-Plated 2 16 981 759 Screw, Pan, 4-40 x 0.312 in., Steel, Black Oxide 2 17 981 817 Screw, Shoulder, 10-24 x 0.375 in. 1 C 18 271 626 Plate, Bearing 1 19 271 618 Trigger, Gun, AD-31 1 NOTE A: Used only with swirl nozzle plates. B: Nozzle assemblies must be ordered separately. Refer to the list of wide-pattern swirl nozzle assemblies. C: Apply a threadlocking adhesive. D: Apply Never-Seeze lubricant (P/N 900 341) or equivalent. E: Used with handgun P/N 137 221. F: Used with handgun P/N 137 217. * listed only for AD-31 handgun models AD-31 SCR-WP (P/N 137 221) and AD-31 STR-WP (P/N 137 217) Continued on next page
8-11 4. AD-31 Wide-Pattern Swirl Handgun (RTD Style), Models SCR-WP and STR-WP* List (contd.) Item Part Description Qty Note 20 939 994 Block, Terminal, 1-Station 4 F 21 939 320 Block, Terminal, 3-Station 2 E 22 274 733 Sensor, Resistance Temperature Detector 1 23 986 305 Clip, Wire Retaining 1 24 274 708 Sleeve, Pivot 1 25 981 735 Screw, Fillister, 6-32 x 0.500 in. with Poly-Lok 11 26 105 491 Kit, Pivot Sleeve 1 E 26 105 489 Kit, Pivot Sleeve 1 F --- S Shell, Pivot Sleeve 2 H 981 735 S Screw, Fillister, 6-32 x 0.500 in. with Poly-Lok 4 H 274 345 S Tag, Warning, AD-31 Gun 1 H 981 800 S Screw, Drive, RD, 0 in. x 0.125 in., Zinc 4 H 27 986 322 Retaining Ring, RD, Sect. 5 / 8 in. Inner Diameter 1 28 940 121 O-Ring, Viton, 0.375 in. x 0.500 in. x 0.063 in. 1 E, G 28 940 101 O-Ring, Viton, 0.250 in. x 0.375 in. x 0.063 in. 1 F, G 29 954 012 Back-Up Ring, Single, 3 / 8 in. x 1 / 2 in. 1 E 29 954 036 Back-Up Ring, Single, 1 / 4 in. x 3 / 8 in. 1 F 30 272 404 Bearing, Thrust, With Grease 1 31 986 016 Retaining Ring, 5 / 8 in. Exterior, Heavy Duty 1 32 271 631 Spring, Conical 1 33 983 111 Washer, Lock, Exterior, Split, No. 8, Steel, Zinc-Plated 2 34 981 080 Screw, Fillister, 8-32 x 1.250 in., Steel, Zinc-Plated 2 35 271 688 Connector, Swivel, 5 / 16 in. Hose 1 E 35 272 791 Connector, Swivel 1 F 36 938 130 Heater, Cartridge, 0.375 in. Diameter, 1.00 in. Length, 1 80 Watt, 240 Volt 37 981 073 Screw, Fillister, 8-32 x 0.375 in., Steel, Zinc-Plated 1 38 271 615 Sleeve, Bearing 1 G NOTE E: Used with handgun P/N 137 221. F: Used with handgun P/N 137 217. G: Apply a high-temperature grease (such as silicone lubricating grease, P/N 900 301) that is capable of withstanding 250 C (500 F). H: Available only as part of a kit. See item 26. * listed only for AD-31 handgun models AD-31 SCR-WP (P/N 137 221) and AD-31 STR-WP (P/N 137 217) Continued on next page
8-12 4. AD-31 Wide-Pattern Swirl Handgun (RTD Style), Models SCR-WP and STR-WP* List (contd.) Item Part Description Qty Note 39 271 619 Safety, Gun 1 40 271 620 Spring, Wave, Safety 1 41 274 383 Shell, Gun, Right, Bulk Melter 1 42 274 384 Shell, Gun, Left, Bulk Melter 1 Screw, Drive, RD, 0 x 0.125 in., Zinc 4 H 44 Tag, Hot Surface 1 H 44 Tag, Warning, AD-31 1 H 44 Tag, Information, AD-31 1 H 45 Tag Set, Guns 1 46 983 102 Washer, Lock, English, Split, No. 6, Steel, Zinc-Plated 1 NOTE H: Available only as part of a kit. See item 26. * listed only for AD-31 handgun models AD-31 SCR-WP (P/N 137 221) and AD-31 STR-WP (P/N 137 217)
8-13 1 2 3 4 5 7 9 41 39 40 25 6 8 10 44 11 12 13 38 16 14 45 44 19 15 25 37 46 20 18 21 17 22 23 24 42 21 20 27 28 29 26 25 36 30 31 44 32 20 25 35 33 33 26 34 4203091 Fig. 8-3 AD-31 Wide-Pattern Swirl Handgun (RTD Style), Models SCR-WP and STR-WP
8-14 5. AD-31 Wide-Pattern Swirl Handgun (Thermostat Style) Models SW-WP, SWD-WP, and SWE-WP* List Item Part Description Qty Note 01 102 406 Retainer, Nozzle, Hexagonal, Swirl Gun 1 A 02 Nozzle B 03 137 229 Body, Nozzle, Clamping (Seat) 1 C 04 945 032 O-Ring, Viton, 3 / 8 in. 1 D 05 137 225 Manifold with Tube Assembly 1 06 271 877 Cartridge, Packing, AD-31 1 07 101 887 Clamp, Tube, 0.228 in. 2 08 102 150 Body, Gun, AD-31 1 09 324 268 Tubing, 1 / 8 in. Tygothane 10 984 120 Nut, Hexagonal, No. 10-32, Steel, Zinc-Plated 1 11 271 616 Linkage, Trigger 1 12 271 617 Spring, Compression, 0.620 in. x 0.455 in. Outer 1 Diameter x 0.039 in. 13 985 216 Pin, Dowel, 0.250 in. x 1.250 in. 1 14 324 260 Valve, Handgun, No Bleed 1 15 983 526 Washer, Lock, Exterior, Split, No. 4, Steel, Zinc-Plated 2 16 981 759 Screw, Pan, 4-40 x 0.312 in., Steel, Black Oxide 2 17 981 817 Screw, Shoulder, 10-24 x 0.375 in. 1 C 18 271 626 Plate, Bearing 1 19 271 618 Trigger, Gun, AD-31 1 20 939 320 Block, Terminal, 3-Station 1 21 938 130 Heater, Cartridge, 0.375 in. Diameter, 1.00 in. Length, 80 Watt, 240 Volt 21 157 319 Heater, Cartridge, 0.38 in. Diameter, 1.00 in. Length, 80 Watt, 120 Volt 1 E, F 1 G NOTE A: Used only with swirl nozzle plates. B: Nozzle assemblies must be ordered separately. Refer to the list of wide-pattern swirl nozzle assemblies. C: Apply Never-Seeze lubricant (P/N 900 341) or equivalent. D: Apply a threadlocking adhesive. E: Used with handgun model P/N 137 223. F: Used with handgun model P/N 137 222. G: Used with handgun model P/N 137 224. * listed only for AD-31 handgun model SW-WP (P/N 137 223), model SWD-WP (P/N 137 222), and model SWE-WP (P/N 137 224). Continued on next page
8-15 5. AD-31 Wide-Pattern Swirl Handgun (Thermostat Style) Models SW-WP, SWD-WP, and SWE-WP* List (contd.) Item Part Description Qty Note 22 986 305 Clip, Wire Retaining 1 23 274 708 Sleeve, Pivot 1 24 981 735 Screw, Fillister, 6-32 x 0.500 in. with Poly-Lok 11 25 105 481 Kit, Pivot Sleeve 1 E 25 105 493 Kit, Pivot Sleeve 1 F 25 105 487 Kit, Pivot Sleeve 1 G --- S Shell, Pivot Sleeve 2 I 981 735 S Screw, Fillister, 6-32 x 0.500 in. with Poly-Lok 4 I 274 345 S Tag, Warning, AD-31 Gun 1 I 981 800 S Screw, Drive, RD, 0 in. x 0.125 in., Zinc 4 I 26 986 322 Retaining Ring, RD, Sect. 5 / 8 in. Inner Diameter 1 27 940 101 O-Ring, Viton, 0.250 in. x 0.375 in. x 0.063 in. 1 28 954 036 Back-Up Ring, Single, 1 / 4 in. x 3 / 8 in. 1 29 272 404 Bearing, Thrust, With Grease 1 30 986 016 Retaining Ring, 5 / 8 in. Exterior, Heavy Duty 1 H 31 271 631 Spring, Conical 1 32 983 111 Washer, Lock, Exterior, Split, No. 8, Steel, Zinc-Plated 2 33 981 080 Screw, Fillister, 8-32 x 1.250 in., Steel, Zinc-Plated 2 34 271 632 Connector, Swivel 1 E 34 272 791 Connector, Swivel 1 F 34 274 084 Connector, Swivel, 5 / 8 in.-18 1 G 35 981 000 Screw, Fillister, 5-40 x 0.250 in., Steel, Zinc-Plated 2 36 937 257 Thermostat, AD-31, 375 F 1 37 981 073 Screw, Fillister, 8-32 x 0.375 in., Steel, Zinc-Plated 1 38 271 615 Sleeve, Bearing 1 H NOTE E: Used with handgun model P/N 137 223. F: Used with handgun model P/N 137 222. G: Used with handgun model P/N 137 224. H: Apply a high-temperature grease (such as silicone lubricating grease, P/N 900 301) that is capable of withstanding 250 C (500 F). I: Available only as part of a kit. See item 25. * listed only for AD-31 handgun model SW-WP (P/N 137 223), model SWD-WP (P/N 137 222), and model SWE-WP (P/N 137 224). Continued on next page
8-16 5. AD-31 Wide-Pattern Swirl Handgun (Thermostat Style) Models SW-WP, SWD-WP, and SWE-WP* List (contd.) Item Part Description Qty Note 39 271 619 Safety, Gun 1 40 271 620 Spring, Wave, Safety 1 41 274 383 Shell, Gun, Right, Bulk Melter 1 42 274 384 Shell, Gun, Left, Bulk Melter 1 Screw, Drive, RD, 0 x 0.125 in., Zinc 4 I 44 Tag, Hot Surface 1 I 44 Tag, Warning, AD-31 1 I 44 Tag, Information, AD-31 1 I 45 Tag Set, Guns 1 46 983 102 Washer, Lock, English, Split, No. 6, Steel, Zinc-Plated 1 NOTE I: Available only as part of a kit. See item 25. * listed only for AD-31 handgun model SW-WP (P/N 137 223), model SWD-WP (P/N 137 222), and model SWE-WP (P/N 137 224).
8-17 1 2 3 4 5 7 9 41 39 40 24 6 8 10 44 11 12 13 38 16 14 45 44 19 15 24 37 46 18 20 17 21 22 23 42 35 36 26 27 28 25 24 29 30 44 31 20 24 34 32 32 26 33 4203095 Fig. 8-4 AD-31 Wide-Pattern Swirl Handgun (Thermostat Style), Models SW-WP, SWD-WP, and SWE-WP
8-18 6. NozzlePlatesand Nozzles Swirl nozzle plates and wide-pattern swirl nozzles create circular streams of air that apply tight, overlapping spirals of adhesive to your work surface. The size of the nozzle opening and the length of the nozzle greatly affect the adhesive s flow. Contact your Nordson representative for assistance in selecting the best nozzle plate or nozzle for your uses. Swirl Nozzle Plates Series AD-31 swirl handguns use special nozzle plates to apply adhesive for use in pressure-sensitive applications. The nozzle plate is secured to the handgun by a nozzle retainer (P/N 102 406), included with swirl handguns. Purchase swirl nozzle plates separately. Part Description Note 860 548 Nozzle, Orifice Diameter 0.012 in. 1 860 574 Nozzle, Orifice Diameter 0.014 in. 1 860 575 Nozzle, Orifice Diameter 0.016 in. 1 860 226 Nozzle, Orifice Diameter 0.018 in. 1 860 5 Nozzle, Orifice Diameter 0.020 in. 1 100 728 Nozzle, Orifice Diameter 0.025 in. 1 810 381 Nozzle, Orifice Diameter 0.030 in. 1 810 382 Nozzle, Orifice Diameter 0.040 in. 1 810 300 Nozzle, Orifice Diameter 0.050 in. 1 Fig. 8-5 Swirl Nozzle Plate 4203088
8-19 Wide-Pattern Swirl Nozzle Assemblies Series AD-31 wide-pattern swirl handguns use special, high-flow nozzle assemblies that produce a wide swirl, ideal for applying adhesive to large areas quickly and thoroughly. Each assembly includes a one-piece nozzle-and-retainer that must be purchased separately from the handgun. Part Description Note 131 635 Nozzle, Orifice Diameter 0.046 in., Blue Disk 1 131 998 Nozzle, Orifice Diameter 0.030 in., Black Disk 1 125 607 Nozzle, Orifice Diameter 0.025 in., Gold Disk 1 Fig. 8-6 4203090 Wide-Pattern Swirl Nozzle Assembly 7. Optional Thermostats All thermostatically controlled handguns are available with the following thermostats. Part _F Temperature _C Part _F Temperature _C 804 838 130 55 271 936 300 150 804 837 150 65 271 928 325 165 804 836 175 80 271 929 350 175 804 835 200 95 271 930 375 190 271 933 225 105 271 931 400 205 271 934 250 120 271 932 425 220 271 935 257 135 271 937 450 230
8-20 8. Accessories You can extend the life and increase the performance of your handgun with proper care. Nordson offers cleaning fluids, greases, and kits to help you maintain the condition of your handgun. Part Description Qty Note 270 757 Fluid, Type R, 208 l (55 gal) 1 900 301 Grease, Lubricating, Silicone, 150 g (5.3 oz) 1 902 514 Gloves, Safety 1 324 287 Kit, Air Hose Installation A S Label, Blank, 3.50 in. X 1.375 in. 324 292 S Tube, Air Line 1 901 513 S Regulator, Filter 1 901 254 S Gage, Air, 1 / 8 in. 1 324 522 S Bracket, Filter Regulator 1 324 697 Kit, Flow Switch B S Tube, Paraflex, 1 / 4 in. Outer Diameter, 6 Ft 324 289 S Strap, Cable, 0.06-4.00 in., Black 6 324 522 S Bracket, Filter Regulator 1 324 695 S Nut, Mounting 1 324 853 S Switch, Flow 1 939 004 S Strap, Cable, 0.06-1.75 in., Natural 2 971 156 S Connector, Male, 1 / 4 Tube x 3 / 8 in., Brass 2 971 266 S Elbow, Male, 0.25 in. Tube X 0.25 in. 1 973 084 S Bushing, Pipe, 1 / 2 in. x 3 / 8 in., Steel, Zinc-Plated 2 981 113 S Screw, Fillister, 10-24 x 0.375 in., Steel, Zinc-Plated 2 983 120 S Washer, Lock, English, Split, No. 10, Steel, Nickel-Plated 2 984 121 S Nut, Hexagonal, Mach, No. 10-24, Steel, Zinc-Plated 2 NOTE A: Recommended for use with all AD-31 swirl handguns when supplying air from a remote source. B: Required when using Series 5000 gear-pump applicators to enable proper clutch or motor control.
8-21 9. Recommended Spare To facilitate maintenance and reduce downtime, Nordson recommends that you keep the following parts in stock for basic repair and maintenance. Spare for Swirl Handguns Part Description Qty Note 102 406 Retainer, Nozzle, Hexagonal, Swirl Gun 1 900 301 Grease, Lubricating, Silicone, 150 g (5.3 oz) 1 271 877 Cartridge, Packing, AD-31 1 271 615 Sleeve, Bearing 1 A 274 733 Sensor, Resistance Temperature Detector 1 B, C 937 257 Thermostat, AD-31, 375 F 1 D, E, F 938 130 Heater, Cartridge, 0.375 in. Diameter, 1.00 in. Length, 80 Watt, 240 Volt 271 625 Heater, Cartridge, 0.38 in. Diameter, 1.00 in. Length, 60 Watt, 230 Volt 274 094 Heater, Cartridge, 0.38 in. Diameter, 1.00 in. Length, 65 Watt, 120 Volt 1 B, C 1 D, E 1 F 939 320 Block, Terminal, 3-Station 2 B, E, D, F 939 994 Block, Terminal, 1-Station 4 C 272 404 Bearing, Thrust, With Grease 1 940 101 O-Ring, Viton, 0.250 in. x 0.375 in. x 0.063 in. 1 954 036 Back-Up Ring, Single, 1 / 4 in. x 3 / 8 in. 1 NOTE A: Apply a high-temperature grease (such as silicone lubricating grease, P/N 900 301) that is capable of withstanding 250 C (500 F). B: Used with handgun model SCR P/N 101 207. C: Used with handgun model STR P/N 101 206. D: Used with handgun model SW P/N 101 209. E: Used with handgun model SWD P/N 101 208. F: Used with handgun model SWE P/N 101 210.
8-22 Spare for Wide-Pattern Swirl Handguns Part Description Qty Note 900 301 Grease, Lubricating, Silicone, 150 g (5.3 oz) 1 271 877 Cartridge, Packing, AD-31 1 271 615 Sleeve, Bearing 1 A 274 733 Sensor, Resistance Temperature Detector 1 B, C 937 257 Thermostat, AD-31, 375 F 1 D, E, F 938 130 Heater, Cartridge, 0.375 in. Diameter, 1.00 in. Length, 80 Watt, 240 Volt 157 319 Heater, Cartridge, 0.38 in. Diameter, 1.00 in. Length, 80 Watt, 120 Volt 1 B, C, D, E 1 F 939 320 Block, Terminal, 3-Station 2 B, D, E, F 939 994 Block, Terminal, 1-Station 4 C 137 229 Body, Nozzle, Clamping (Seat) 1 G 137 225 Manifold with Tube Assembly 1 101 887 Clamp, Tube, 0.228 in. 2 324 260 Valve, Handgun, No Bleed 1 272 404 Bearing, Thrust, With Grease 1 940 101 O-Ring, Viton, 0.250 in. x 0.375 in. x 0.063 in. 1 954 036 Back-Up Ring, Single, 1 / 4 in. x 3 / 8 in. 1 NOTE A: Apply a high-temperature grease (such as silicone lubricating grease, P/N 900 301) that is capable of withstanding 250 C (500 F). B: Used with handgun model P/N 137 221. C: Used with handgun model P/N 137 217. D: Used with handgun model P/N 137 223. E: Used with handgun model P/N 137 222. F: Used with handgun model P/N 137 224. G: Apply Never-Seeze lubricant (P/N 900 341) or equivalent.