MANUAL
Hitchpole, centre frame 1 Centre frame wheels & roller 3 Centre & wing frames Wing frame wheels & roller 9 Hydraulics 11 Clearance lights 13 Operations 1 Safety, warranty 1 SAFETY Industrial Drive, Box 830 Regina, Sask. Canada SP 3B1 Toll Free: 1-800-66-3 306 3-3- fx Email: degelman@degelman.com www.degelman.com The safety instructions that follow pertain only to this specific equipment. You should be aware of agricultural & industrial safety especially related to heavy equipment. If you are not familiar with safety procedures then you should get training. Improper use will result in maiming or death.
Hitch pole & centre frame 1 1 1 18 1 8 9 6 16 18 19 1 11 13 1 3 p1
Transport Floatation plate USE TRANSPORT PIN Field 1 1 / Grease point Every hrs 11833 Grease fitting Store transport pin 1 801 Centre frame 1 300 Hitch pole 1 3 368 Pole pin 11803 Bolt /8 x 3-1/ 118 Lock nut /8 UNITQ 3 6 13001 Rachet jack 1 13009 Jack handle 1 8 11889 Hair pin 8 9 1303 Pin 1 x -1/8 EFF 3 Floatation plate 1 11 31 Bent pin 1 1 118901 Lynch pin 1 13 303 Bolt 1-1/ x c/w ftg 1 118 Lock nut 1-1/ 1 1 1 1300 Sidewind jack 1 16 1330 Manual holder 1 1 11813 Bolt 1/ x 1 18 118 Flat washer 1/ 8 19 11883 Lock nut 1/ p
Centre frame, wheels & roller 1 3 9 0 19 1 1 18 Store hyd cyl transport lock 8 8 9 16 1 6 1 3 1 Grease point Every hrs 11 p3 13
The wing rollers use the same bearing system 1 301 Centre roller 1 11006 Bearing 3 110 Lock ring 116 Bearing insert 11 Flange casting 6 360 Bushing 11806 Bolt /8 x 8 8 11808 Lock washer /8 8 9 1180 Nut /8 8 8 Rockshaft 1 11 10 Cast bearing cap 1 100 Cast bearing base 13 118083 Bolt 3/ x 1/ 8 1 6180 Shim 8 1 11816 Flat washer 3/ 8 16 118 Lock nut 3/ 8 3 1313 Hub & spindle 11883 Cotter pin 1 13101 Dust cap - CTD 1 6 1183 Slotted nut 1 UNS 1 130 Flat washer 1 SAE 1 8 13 Cone bearing 1 9 13 Bearing cup 1 30 13100 Hub H618G - CTD 1 31 133 Bearing cup 1 3 13 Cone bearing 1 33 136 Dust seal 1 3 1313 Spindle 1 3 11808 Bolt 1/ x 3 1/ 1 36 1180 Lock nut 1/ UNITQ 1 Per wheel 3 1 136 Wheel 18 11891 Whl bolt 9/16 x 1 3/ 19 1003 Tire 9.Lx1 6ply 0 1006 Valve TR1 1 1301 Rim 1 x 8 6 bolt 11861 Jam nut 9/16 UNF 36 3 33 3 31 8 9 30 3 6 p
Centre & wing frames 1 Hydraulic cylinder 31/x16x11/ 3 16 16 0 1 1 13 1 9 8 6 11 3 Centre frame 8 Truss arm 1 Wing frame p
1 0 18 0 19 1 30 LH wing frame 1 3301 RH 1 3 LH auto fold latch 1 36 RH 1 3 11808 Bolt 1/ x 3 1/ 31 Autofold collar 1180 Lock nut 1/ UNITQ 6 11868 Bolt 1/ x 1/ 1303 Comp. spring 8 1181 Flat washer 1/ Lock nut 1/ UNITQ 9 816 Cable 11883 Cotter pin 11 11996 Flat Washer M18 SAE 1 3001 Cable pin 13 3188 Eyebolt /8 x 1/ 1 1183 Flat washer /8 SAE 1 118 Lock nut /8 UNITQ 16 111 Bushing 1-1/ x 3/ 1 3 LH autofold arm 1 309 RH 1 3 Bolt 1/ x 3 1/ Autofold collar Lock nut 1/ UNITQ 6 18 38 Swing arm holder 19 11806 Bolt /8 x 8 16 0 1181 Flat washer /8 16 1 11808 Lock washer /8 8 16 1180 Nut /8 8 16 Grand total p6
Centre & wing frames 9 1 11 1 13 p
3 3 1 1 366 Cross joint 33 Cross joint pin 3 11809 Bolt /8 x 118 Lock nut /8 UNITQ 6 319 Truss arm 6 118116 Bolt 1x1/ 118 Lock washer 1 8 1181 Nut 1 9 13111 Hose holder 1 11806 Bolt /8 x 1 11 1181 Flat washer /8 1 1 11808 Lock washer 1 13 1180 Nut /8 1 1 116 Safety chain 1 8 p8
Wing frame, wheels & roller Install roller as with centre frame 1 1 11 1 13 1 16 136 Wheel 11 11891 Whlbolt9/16x13/ 1 1 1003 Tire 9.Lx1 6ply 13 1006 Valve TR1 1 1301 Rim 1x8 6 bolt 1 11861 Jam nut 9/16 UNF 1 1 33 Wing roller 311 LH end wheel strut 1 3 RH 1 303 Bolt 1 1/ x c/w ftg 118 Lock nut 1 1/ 6 31 Upper link plate 306 Link bar Bolt 1 1/ x c/w ftg 6 Lock nut 1 1/ 6 8 1108 Bushing 1 1/ x 1 1 9 111 Bushing 1 1/ x 3/ 1 Grand total 16 13138 Hub & bent spindle 1 11883 Cotter pin 1 18 13101 Dust cap - CTD 1 19 1183 Slotted nut 1 UNS 1 0 130 Flat washer 1 SAE 1 1 13 Cone bearing 1 13 Bearing cup 1 3 13100 Hub H618G - CTD 1 133 Bearing cup 1 13 Cone bearing 1 6 136 Dust seal 1 13139 Bent spindle 1 8 118900 Hitch pin 1 9 118901 Lynch pin 1 Per wheel p9
Hydraulic cylinder 31/x16x11/ 9 8 6 Store hyd cyl transport lock 18 1 Grease point Every 0 hrs 11833 Grease fitting 19 0 1 9 3 6 8 p
Grease point Every hrs Hydraulics 3 8 9 1 6 8 9 18 3 1/ x 16 x 1 1/ Cylinder four per machine 1 11803 Barrel 1 168 Lock ring 1 3 166 Open cap 1 1 USE TRANSPORT LOCK 1099 Rod & clevis 1 1663 Piston 1 6 1181 Lock nut /8 UNF UNITQ 1 118930 Clevis pin 11 1 1 8 1189 Lock washer 1/ 9 11896 Bolt 1/ x 1 13 1 Seal kit 3 1/ x 1 1/ 1 11 3990 Transport lock 1 300 Wire lock pin 13 808 Hose clamp 1 809 Top plate 1 1181 Bolt /16 x 1 1/ p11 Store transport lock
() () 116 Coupling 1/ NPT (male tip) 111 Nipple (M) 1/ NPT x 3/ JIC 11 Tee 3/ JIC M 1 Tee 3/ M JIC x JIC x ORB 1 Elbow 3/ M JIC x ORB () (Hose length in inches) 160 Hose 3/8 x () (0) 16636 Hose 3/8 x () 169 Hose 3/8 x (0) 1663 Hose 3/8 x (96) Ports face up (96) Ports face up (96) p1
Clearance lights 11&1 1 190 Pole plug 1 0 16/ SuperVU line 8ft 1 1 3 06 Junction box 1 19033 Straight cord conn. 3 1181 Plastic locknut 1/ NPT 3 6 1903 Terminal strip conn. 1 11816 Screw #8, 3/ 8 1183 Screw 1/ self-tap 9 11888 Rubber washer 3/16ID 18 1901 LH Dual lamp 1 1900 RH 1 19 36 Lamp/SMV brkt, left side 1 0 1186 Bolt 1/ x 1 1/ 8 1 11883 Lock nut 1/ 8 16 1 03 16/3 SuperVu line 0ft 11 0 Loom 60 1 190 Clamp 3/8 cushion 13 0 Grommet 3/8 1 1901 Grommet 1/ 1 6163 Loom 16 1903 Butt splice crimp 16ga 1 190 Triplug 18 113 SMV sign 1 3 11813 Bolt 1/ x 1 11833 Lock washer 1/ 1180 Nut 1/ 6 118009 Bolt 1/ x 1-1/ 1180 Lock washer 1/ 8 1180 Nut 1/ 9 3 Lamp brkt, right side 1 13 1 Make sure blank faces forward colours face back 3 0 Orange 18 1 Red 19 8 8 Left side 6 9 6 Right side p13
Y brown G G W B R RH turn Ground Tail LH turn G W G W Right wire B B Left wire Splice R W brown Amber light Ground Red light 1 POLE PLUG 16/ WIRE JUNCTION BOX 16/3 WIRE TRIPLUG 1 6 9 3 3 8 18 Cut loom for Triplug 1 16 1 1 13 1 11 p1
Transport Latch open A PREPARE Take off transport locks Cable taut Set floatation plate to field position Latch closed D SET LATCH CLOSED Drop drums with wings almost out Back up until wings all the way out then wing arm clicks in Cable slack p1
C BRING WINGS OUT Back up slowly B ANGLE OUT TRANSPORT WHEEL Drop roller Turn axle Lift roller Field AUTOFOLD LATCH ADJUSTMENT: After a while the cable will stretch and the latch won t open to free the Swing Arm. To adjust, have the wings out. With the swing arm pipe in the latch and the latch open just enough for the swing arm to clear adjust the nut on the eyebolt. That is the correct degree of tension for the cable p16
Safety You are responsible for your own safety. If you don t know basic agriculture & industrial safety, find out. Owners of equipment must by law give operating instructions to other operators such as family members or a hired hand. Making any design changes to equipment could cause a hazard and damage your machine. Wear proper safety equipment. Have handy first aid kit & fire extinguisher. Before working on machine: Turn tractor off Set controls in neutral Remove ignition key Clean all reflectors and lights. Keep all parts clean Replace worn or damaged parts Don t try any makeshift repairs Before operating check that everything is tight and not broken. KILLED, INJURED or SAFE? YOUR CHOICE START UP AND ONGOING CHECK LIST: Grease all fittings Check all bolt tightness Repeat after a days use and check for hydraulic leaks Retorque bolts Adjust hitch height; Set trailer so it is parallel to ground Use a drawbar pin with mechanical retainer Check tire pressure (36 PSI) Oil level in tractor s hydraulic reservoir. Inspect lines, hoses, fitting & couplers. Wipe couplers with clean cloth. TRANSPORTING Use Safety Lights When in transport position make sure transport pin is in place Clean SMV sign and reflectors. MAINTENANCE? HRS Hyd. fluid leaks Damaged hoses Tire pressure 36 PSI HRS Lube points indicated 0 HRS Working points & pins Safety signs clean ANNUAL Bolt tightness Wheel bearings Latch mechanism Cable assembly TORQUE SETTINGS Gr.8 3/8 6 lb-ft /8 3/ 00 /8 60 Hyd. fitting 3/ lb-ft Gr.8.8 M8 0 lb-ft M 0 Gr..9 M 80 lb-ft All hardware - Hex head, Plated, Gr. UNC Hoses - 3/8 female swivel JIC Unless stated otherwise HYDRAULICS Wear gloves and eye protection when searching for leaks. Use a piece of wood or cardboard but not your hand. High pressure oil will penetrate your skin. If that happens you risk serious injury. p1 DECAL REPLACEMENT It is important to understand and follow the information found on all safety decals. If safety decals are damaged, missing, or illedgible they must be replaced. Replacement decals are available by request. Call toll free: 1.800.66.3 Decal # Decal Description 1008 Decal, Degelman 6 x 3/ IN 3 1383 Decal, Caution - 6 Point Safety 1 138 Decal, Important - Remove Transport Bar 1 Decal, Danger - Stay Clear Crushing Hzd. 1 1 Decal, Important - Position Float Plate 1 1 Decal, Important - End Wheel 1 Decal, Reflector - Amber x 9 IN 6 11 Decal, Landroller 6 1316 Decal, Read Operators Manual 1
WARRANTY Degelman Industries warrants this product to the original owner for a period of one (1) year parts and labour and two () years parts from the date of purchase. All matters related to the warranty of our products must be handled through the authorized selling dealer. Warranty does not cover normal wear of the machine components or damages caused by lack of maintenance or misuse, and is subject to the following provisions. REPLACEMENT PARTS: Will be warranted for a period of ninety (90) days. WARRANTY ON MACHINES USED FOR CUSTOM WORK, RENTALS OR INDUSTRIAL USE: Will be warranted as stated above, with the exception that it will be for a period of ninety (90) days only. TIRES: Will be adjusted for warranty by tire manufacturer. LABOUR: Any labour subject to warranty must be authorized by a Degelman representative before work is started. Warranty labour allowance and rates will be handled according to established warranty service policy. GOVERNMENT LEGISLATION: Warranty terms and conditions are subject to Provincial or State legislation. MODIFICATIONS: Warranty will be void if any component is altered or modified, unless written authorization is granted by Degelman Industries Limited. WARRANTY ON ATTACHED EQUIPMENT: No responsibility will be assumed for whatever damages may occur to persons, tractors or property. 0 p18