DG ommercial 6 Ton Packaged Gas/ Electric Units up to. IEER 80% AFUE ooling apacity: Up to 7,000 BTU/h Heating Input: 8,000 BTU/h ontents Nomenclature... Product Specifications... Expanded ooling Data... 7 Airflow Data... rankcase Heater... Electrical Data... Dimensions... Wiring Diagrams... 8 for Models with DD ontrols... Accessories... Standard Features Patented tubular heat exchanger Highefficiency scroll compressor High and lowpressure switches opper tube / aluminum fin coils ontactor with lugs Highcapacity, steelcased filter drier volt terminal strip onvertible airflow orientation Easy to service Builtin filter rack with standard " filters Bottom utility entry omplies with alifornia Low NOx emissions standards Single speed blower motor units meet the performance specified in Table 6.8.A of ASHRAE Standard 90.00 AHRI ertified; ETL Listed Twospeed blower motor, TXV and twostage compressor meet the performance specified as of //06 in Table 6.8. of ASHRAE Standard 90.0 abinet Features Heavygauge, galvanizedsteel cabinet with UVresistant powderpaint finish Full Perimeter Rail Sloped drain pan * omplete warranty details available from your local distributor or manufacturer s representative or at www.daikincomfort.com. SSDG www.daikinac.com 7/7 Supersedes /7
Nomenclature D G 060 090 B * * * A *,,6 7,8,9 0 6 Revision Levels Major & Minor Brand FactoryInstalled Options D Daikin X No Options A Nonpowered convenience outlet onfiguration B Powered convenience outlet Standard Efficiency (6 Tons) Lowambient kit S Standard Efficiency ( Tons) D Return air smoke detector T High Efficiency ( Tons) E Supply air smoke detector F Nonpowered convenience outlet; Application Lowambient kit ooling G Nonpowered convenience outlet; G Gas Heat Return air smoke detector H Heat Pump H Nonpowered convenience outlet; Supply air smoke detector Nominal ooling apacity J Nonpowered convenience outlet; 06 Tons 0 8½ Tons 00 Tons Return & Supply air smoke detectors 08 Tons 0 0 Tons K Nonpowered convenience outlet; 060 Tons 0 ½ tons Lowambient kit; Supply air smoke detector 07 6 Tons 80 Tons L Nonpowered convenience outlet; 090 7½ Tons 0 0 Tons Lowambient kit Return & Supply air smoke detectors Nominal Heating apacity M Powered convenience outlet; Gas/Electric A/ H/P FactoryInstalled Electric Heat Lowambient kit 0,000 BTU/h XXX No Heat N Powered convenience outlet; 070 70,000 BTU/h 00 0 kw 00 0 kw Return air smoke detector 090 90,000 BTU/h 0 kw 0 0 kw O Powered convenience outlet;,000 BTU/h 06 kw 0 kw Return & Supply air smoke detectors 0 0,000 BTU/h 08 8 kw 06 kw P Powered convenience outlet; 0 0,000 BTU/h 00 0 kw 060 60 kw Supply air smoke detector 0 0,000 BTU/h 0 kw Q Powered convenience outlet; Lowambient 00 00,000 BTU/h kit; Return air smoke detector See product specifications for heat size(s) available for each capacity. R Powered convenience outlet; Lowambient Voltage kit; Supply air smoke detector 080//60 60//60 T Powered convenience outlet; Lowambient 080//60 7 7//60 kit; Return & Supply air smoke detectors U Nonpowered convenience outlet; Supply Fan/Drive Type/Motor Lowambient kit; Return air smoke detector B Belt Drive (single speed) V TwoSpeed Belt Drive (also designates 6Ton V Lowambient kit; Return air smoke detector D Direct Drive ( Tons) with twostage compressor) W Lowambient kit; Supply air smoke detector H High Static (singlespeed Belt Drive models only) Y Lowambient kit; Return & Supply FactoryInstalled Options air smoke detectors A Ultra LowLeak Downflow Economizer R Ultra LowLeak Downflow Economizer; Z Return & Supply air smoke detectors B DDBAnet protocol DDBAnet protocol; F Ultra LowLeak Downflow Economizer; Disconnect Switch (nonfused) DDBAnet protocol V LowLeak Downflow Economizer FactoryInstalled Options H Disconnect Switch (nonfused) W LowLeak Downflow Economizer X Standard Aluminized Heat Exchanger J Ultra LowLeak Downflow Economizer; Disconnect Switch (nonfused) S StainlessSteel Heat Exchanger Disconnect Switch (nonfused) X No Options D Hinged Panels M Disconnect Switch (nonfused); DDBAnet protocol K StainlessSteel Heat Exchanger; Hinged Panels Note: Not all options available for all products. B Phase Monitor X= No Options in character th J Stainless Steel Heat Exchanger; Phase Monitor M Hinged Panel; Phase Monitor L StainlessSteel Heat Exchanger; Hinged Panels; Phase Monitor www.daikinac.com SSDG
FactoryInstalled Options StainlessSteel Heat Exchanger (Gas only units): A tubular heat exchanger made of 09type stainless steel is installed in the unit. LowAmbient Kit: Allows for cooling operation at lower outdoor temperatures. On the to 6ton units, cooling operation is extended from 60 F ambient temperature to F outside air temperature. On 7½ 0 ton units, cooling operation is extended from F ambient temperature to 0 F outside air temperature. For ton units, cooling operation is extended from F ambient temperature to 0 F outside air temperature. Economizers (Downflow): Based on air conditions, can provide outside air to cool the space. Electric Heat Kits (heat pump and cooling units only): Available in all voltage options. Nonpowered onvenience Outlet: A 0V, A, GFI outlet makes it easier for technicians to service the unit once an electrician runs power to the outlet. Powered onvenience Outlet: A 0V, A, GFI outlet powered with a transformer built into the unit. When a factoryinstalled powered convenience outlet is installed in the equipment, the unit MA (Min. ircuit Ampacity) will increase by 7.A for 08/0V units, increase by.7a for 60V units, and by A for 7V units. The MOP (Max. Overcurrent Protection) device must be sized accordingly. Disconnect Switch (nonfused; phase units only): A disconnect switch is installed in the unit and factory wiring will be complete from the switch to the unit. Please note that for air conditioning and heat pump models, the appropriate electric heat kit must be ordered to be factoryinstalled along with the disconnect switch (nonfused) when it is ordered. Please note that for models with a powered convenience outlet option and a disconnect switch (nonfused) option, the power to the powered convenience outlet will be shut off when the disconnect switch (nonfused) is in the off position. Return Air and/or Supply Air Smoke Detectors: Return air and/or supply air smoke detectors are installed in the unit. Hinged Access Panels: Allows access to unit s major components. ombined with latches for easy access to control box, compressor, filters and blower motor. Available on all units. Twospeed indoor fan blower models are available on 6, 7½, 8½, 0, ½,, 0 & ton units. Section 6...0.b of ASHRAE Standard 90.00 and Section 6...a of ASHRAE Standard 90.0 require a minimum of two fan speeds. Section 0.(m) of alifornia Energy ommission Title 0 contains a similar provision. When the units with the twospeed indoor fan blowers operate on a call for the first stage of cooling, the fan operates at low speed, which is 66% of full speed. When the units operate on a call for the second stage of cooling, the fan operates at full speed. In heating operation, the fan operates at full speed. During ventilation operation, the fan operates at low speed. Return Air and/or Supply Air Smoke Detectors: Return air and/or supply air smoke detectors are installed in the unit. Hinged Access Panels: Allows access to unit s major components. ombined with latches for easy access to control box, compressor, filters and blower motor. Available on all models. Phase Monitor: Phase monitor ( phase only), available for ton DS, D and DT series models. Phase monitor shall provide protection for motors and compressors against problems caused by phase loss, phase reversal and phase unbalance. Phase monitor is equipped with an LED that provides an ON or FAULT indicator. DD ontroller: DD communicating controller, available for ton DS, D and DT series models with onboard BAnet communication interface. SSDG www.daikinac.com
Product Specifications 6 Tons DG07 090V***A* DG07 090V***A* DG07 0907V***A* ooling apacity Total BTU/h 69,000 69,000 69,000 Sensible BTU/h,000,000,000 EER / IEER./../../. Decibels 78 78 78 AHRI Number 8980 8980 8980 Heating apacity High Input / Output KBTU/h 9 / 7.6 9 / 7.6 9 / 7.6 Low Input/ Output KBTU/h 69 / 69 / 69 / Steady State Efficiency 80 80 80 Temperature Rise Range ( F) 00 / 00 / 00 / No. of Burners Evaporator Motor / oil Motor Type speed Belt Drive speed Belt Drive speed Belt Drive # of Wheels (D x W) (" x 0") (" x 0") (" x 0") Indoor Nominal FM,0,0,0 Indoor Motor FLA (ooling) 6.0.9. Horsepower RPM.0,7.0,7.0,7 Piston Size (ooling) TXV TXV TXV Filter Size (Qty) () 6" x 0" x " () 6" x 0" x " () 6" x 0" x " Drain Size (NPT) ¾" ¾" ¾" R0A Refrigerant harge (oz.) 6.0 6.0 6.0 Evaporator oil Face Area (ft²) 8.9 8.9 8.9 Rows Deep/ Fins per Inch /6 /6 /6 Motor Sheave VL X 7/8 VL X 7/8 VL X 7/8 Blower Sheave AK9 X AK9 X AK9 X ondenser Fan / oil Quantity of ondenser Fan Motors Horsepower RPM ⅓,07 ⅓,07 ⅓,07 Fan Diameter/ # Fan Blades / / / Outdoor Nominal FM,00,00,00 Face Area (ft²) 9 9 9 Rows Deep/ Fins per Inch /7 /7 /7 ompressor Quantity / Stage / Two / Two / Two Type Scroll Scroll Scroll ompressor RLA / LRA 7.6/6 8./66. 6./. Electrical Data Voltage/ Phase/ Frequency 080/ / 60 60/ / 60 7/ / 60 Outdoor Fan FLA.0 0.8 0.67 Total Unit Amps.6. 9. Min. ircuit Ampacity¹ 0.0..0 Max. Overcurrent Protection².0 0.0.0 Entrance Power Supply."."." Entrance ontrol Voltage ½" ½" ½" Operating Weight (lbs) 680 680 680 Ship Weight (lbs) 69 69 69 ¹ Wire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HARtype circuit breakers of the same size as noted. Notes Always check the S&R plate for electrical data on the unit being installed. When a factoryinstalled powered convenience outlet is installed in the equipment, the unit MA (Min. ircuit Ampacity) will increase by 7.A for 08/0V units, increase by.7a for 60V units, and by A for 7V units. The MOP (Max. Overcurrent Protection) device must be sized accordingly. www.daikinac.com SSDG
Product Specifications 6 Tons (cont.) DG07 V***A* DG07 V***A* DG07 7V***A* ooling apacity Total BTU/h 69,000 69,000 69,000 Sensible BTU/h,000,000,000 EER / IEER./../../. Decibels 78 78 78 AHRI Number 8980 8980 8980 Heating apacity High Input / Output KBTU/h / 9 / 9 / 9 Low Input/ Output KBTU/h 86 / 69 86 / 69 86 / 69 Steady State Efficiency 80 80 80 Temperature Rise Range ( F) / 00 / 00 / 00 No. of Burners Evaporator Motor / oil Motor Type speed Belt Drive speed Belt Drive speed Belt Drive # of Wheels (D x W) (" x 0") (" x 0") (" x 0") Indoor Nominal FM,0,0,0 Indoor Motor FLA (ooling) 6.0.9. Horsepower RPM.0,7.0,7.0,7 Piston Size (ooling) TXV TXV TXV Filter Size (Qty) () 6" x 0" x " () 6" x 0" x " () 6" x 0" x " Drain Size (NPT) ¾" ¾" ¾" R0A Refrigerant harge (oz.) 6.0 6.0 6.0 Evaporator oil Face Area (ft²) 8.9 8.9 8.9 Rows Deep/ Fins per Inch /6 /6 /6 Motor Sheave VL X 7/8 VL X 7/8 VL X 7/8 Blower Sheave AK9 X AK9 X AK9 X ondenser Fan / oil Quantity of ondenser Fan Motors Horsepower RPM ⅓,07 ⅓,07 ⅓,07 Fan Diameter/ # Fan Blades / / / Outdoor Nominal FM,00,00,00 Face Area (ft²) 9 9 9 Rows Deep/ Fins per Inch /7 /7 /7 ompressor Quantity / Stage / Two / Two / Two Type Scroll Scroll Scroll ompressor RLA / LRA 7.6/6 8./66. 6./. Electrical Data Voltage/ Phase/ Frequency 080/ / 60 60/ / 60 7/ / 60 Outdoor Fan FLA.0 0.8 0.67 Total Unit Amps.6. 9. Min. ircuit Ampacity¹ 0.0..0 Max. Overcurrent Protection².0 0.0.0 Entrance Power Supply."."." Entrance ontrol Voltage ½" ½" ½" Operating Weight (lbs) 68 68 68 Ship Weight (lbs) 700 700 700 ¹ Wire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HARtype circuit breakers of the same size as noted. Notes Always check the S&R plate for electrical data on the unit being installed. When a factoryinstalled powered convenience outlet is installed in the equipment, the unit MA (Min. ircuit Ampacity) will increase by 7.A for 08/0V units, increase by.7a for 60V units, and by A for 7V units. The MOP (Max. Overcurrent Protection) device must be sized accordingly. SSDG www.daikinac.com
Product Specifications 6 Tons (cont.) DG07 0B***A* DG07 0V***A* DG07 0B***A* DG07 0V***A* DG07 07B***A* DG07 07V***A* ooling apacity Total BTU/h 7,000 69,000 7,000 69,000 7,000 69,000 Sensible BTU/h 9,800,000 9,800,000 9,800,000 EER / IEER.0 /../..0 /../..0 /../. Decibels 78 78 78 78 78 78 AHRI Number 669 8980 669 8980 669 8980 Heating apacity High Input / Output KBTU/h 8 / 0. 8 / 0. 8 / 0. 8 / 0. 8 / 0. 8 / 0. Low Input/ Output KBTU/h 0 / 8 0 / 8 0 / 8 0 / 8 0 / 8 0 / 8 Steady State Efficiency 80 80 80 80 80 80 Temperature Rise Range ( F) 060 / 060 / 060 / 060 / 060 / 060 / No. of Burners 6 6 6 6 6 6 Evaporator Motor / oil Motor Type Belt Drive speed Belt Drive Belt Drive speed Belt Drive Belt Drive speed Belt Drive # of Wheels (D x W) (" x 0") (" x 0") (" x 0") (" x 0") (" x 0") (" x 0") Indoor Nominal FM,0,0,0,0,0,0 Indoor Motor FLA (ooling).0 6.0..9.. Horsepower RPM.,7.0,7.,7.0,7.,7.0,7 Piston Size (ooling) 0.09 TXV 0.09 TXV 0.09 TXV Filter Size (Qty) () 6" x 0" x " () 6" x 0" x " () 6" x 0" x " () 6" x 0" x " () 6" x 0" x " () 6" x 0" x " Drain Size (NPT) ¾" ¾" ¾" ¾" ¾" ¾" R0A Refrigerant harge (oz.) 6.0 6.0 6.0 6.0 6.0 6.0 Evaporator oil Face Area (ft²) 8.9 8.9 8.9 8.9 8.9 8.9 Rows Deep/ Fins per Inch / 6 / 6 / 6 / 6 / 6 / 6 Motor Sheave VL X 7/8 VL X 7/8 VL X 7/8 VL X 7/8 VL X 7/8 VL X 7/8 Blower Sheave AK9 X AK9 X AK9 X AK9 X AK9 X AK9 X Belt AX AX AX AX AX AX ondenser Fan / oil Quantity of ondenser Fan Motors Horsepower RPM ⅓,07 ⅓,07 ⅓,07 ⅓,07 ⅓,07 ⅓,07 Fan Diameter/ # Fan Blades / / / / / / Outdoor Nominal FM,00,00,00,00,00,00 Face Area (ft²) 9 9 9 9 9 9 Rows Deep/ Fins per Inch / 7 / 7 / 7 / 7 / 7 / 7 ompressor Quantity / Stage / Single / Two / Single / Two / Single / Two Type Scroll Scroll Scroll Scroll Scroll Scroll ompressor RLA / LRA 9/ 7.6/6 9.7/ 6 8./66. 7./ 0 6./. Electrical Data Voltage/ Phase/ Frequency 080/ / 60 080/ / 60 60/ / 60 60/ / 60 7/ / 60 7/ / 60 Outdoor Fan FLA.90.00.0 0.90 0.90 0.70 Total Unit Amps.9.6.. 0.6 9. Min. ircuit Ampacity¹ 0 6..0 Max. Overcurrent Protection² 0 Entrance Power Supply."."."."."." Entrance ontrol Voltage ½" ½" ½" ½" ½" ½" Operating Weight (lbs) 690 690 690 690 690 690 Ship Weight (lbs) 7 7 7 7 7 7 ¹ Wire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HARtype circuit breakers of the same size as noted. Notes Always check the S&R plate for electrical data on the unit being installed. When a factoryinstalled powered convenience outlet is installed in the equipment, the unit MA (Min. ircuit Ampacity) will increase by 7.A for 08/0V units, increase by.7a for 60V units, and by A for 7V units. The MOP (Max. Overcurrent Protection) device must be sized accordingly. 6 www.daikinac.com SSDG
Expanded ooling Data 6 Tons Single Speed Outdoor Ambient Temperature 6 7 8 9 0 Entering Indoor Wet Bulb Temperature IDB Airflow 9 6 67 7 9 6 67 7 9 6 67 7 9 6 67 7 9 6 67 7 9 6 67 7 70 60 0 00 MBh 69.6 7. 79.0 68.0 70. 77. 66. 68.8 7. 6.7 67. 7. 6. 6.7 69.8 7.0 9.0 6.7 S/T 0.7 0.6 0. 0.78 0.6 0. 0.80 0.67 0.6 0.8 0.69 0.8 0.86 0.7 0.0 0.86 0.7 0.0 T 8 6 8 6 8 6 9 6 8 6 7 kw.0.0..7.8.7.79.9 6.09 6.08 6. 6.0 6. 6.6 6.66 6. 6.67 6.89 HI PR 67 6 8 99 99 0 67 88 8 6 6 8 LO PR 08 8 6 7 0 8 6 MBh 67. 70.0 76.7 66.0 68. 7.9 6. 66.8 7. 6.8 6. 7. 9.7 6.9 67.8. 7. 6.8 S/T 0.7 0.60 0. 0.7 0.6 0. 0.76 0.6 0. 0.79 0.66 0.6 0.8 0.68 0.7 0.8 0.69 0.8 T 9 6 9 7 9 7 9 7 9 7 8 kw.06.6....70.7.87 6.0 6.0 6.6 6. 6.7 6. 6.6 6.8 6.6 6.8 HI PR 0 6 6 8 96 97 9 7 8 6 8 80 09 0 77 LO PR 07 0 7 6 9 7 0 MBh 6. 6.6 70.8 60.9 6. 69. 9. 6.6 67. 8.0 60. 6.9. 7. 6.6.0.9 8.0 S/T 0.69 0.8 0.0 0.7 0.60 0. 0.7 0.6 0. 0.76 0.6 0. 0.79 0.66 0.6 0.80 0.66 0.6 T 9 7 0 7 0 7 0 7 9 7 8 6 kw.9.0.9.0..7.6.7.90.89 6.0 6.0 6. 6. 6. 6. 6.6 6.67 HI PR 6 7 87 88 0 7 8 7 69 97 9 07 8 6 LO PR 0 0 0 09 6 7 9 7 9 9 8 0 7 60 0 00 MBh 70.8 7.8 78.9 8.6 69. 7. 77.0 8.7 67. 69. 7. 80.7 6.8 67.8 7. 78.7 6. 6. 69.7 7.8 7.9 9.6 6. 69. S/T 0.86 0.77 0.8 0.7 0.89 0.79 0.60 0.9 0.9 0.8 0.6 0.0 0.9 0.8 0.6 0. 0.97 0.87 0.66 0. 0.98 0.88 0.67 0. T 9 6 0 6 0 6 0 6 9 6 0 8 0 kw...0.6..6.79.97.8.96 6. 6. 6. 6.6 6. 6.66 6.7 6. 6.7 6.9 6.9 6.7 6.9 7.7 HI PR 7 69 8 66 86 0 0 6 9 7 9 08 88 7 9 8 6 87 08 LO PR 09 6 6 9 7 9 8 6 0 6 6 8 68 MBh 68.7 70.7 76.6 8. 67. 69. 7.8 80. 6. 67. 7.0 78. 6.9 6.8 7. 76. 60.7 6. 67.7 7.6 6. 7.9 6.7 67. S/T 0.8 0.7 0. 0.6 0.8 0.76 0.7 0.7 0.87 0.78 0.9 0.8 0.90 0.80 0.6 0.9 0.9 0.8 0.6 0.0 0.9 0.8 0.6 0. T 0 7 0 7 0 7 7 0 7 9 6 kw.0.0.6..7.8.7.9.79.9 6.0 6.9 6.08 6. 6.0 6.6 6. 6.6 6.66 6.88 6. 6.68 6.89 7. HI PR 67 78 6 8 99 00 0 67. 88 0 8 6 6 8 0 LO PR 08 8 6 7 6 0 8 6 6 67 MBh 6. 6. 70.7 7.8 6.9 6.8 69.0 7. 60. 6. 67. 7. 9.0 60.7 6.7 70. 6.0 7.7 6. 67.0.9. 7.8 6. S/T 0.79 0.70 0. 0. 0.8 0.7 0. 0.6 0.8 0.7 0.7 0.6 0.86 0.77 0.8 0.8 0.90 0.80 0.6 0.9 0.90 0.8 0.6 0.9 T 7 7 7 7 7 9 6 kw.99.08..9...6.79.66.77.9 6..9 6.06 6. 6. 6.7 6.0 6.0 6.7 6.8 6. 6.7 6.9 HI PR 8 9 70 7 90 0 9 0 6 76 9 7 0 67 88 LO PR 0 9 0 7 8 6 0 8 0 9 6 7 6 9 6 IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AA (TVA) Rating conditions kw = Total system power High and low pressures are measured at the liquid and suction service valves. Amps = outdoor unit amps (comp.fan) SSDG www.daikinac.com 7
Expanded ooling Data 6 Tons Single Speed (cont.) Outdoor Ambient Temperature 6 7 8 9 0 Entering Indoor Wet Bulb Temperature IDB Airflow 9 6 67 7 9 6 67 7 9 6 67 7 9 6 67 7 9 6 67 7 9 6 67 7 80 60 0 00 MBh 7.0 7.6 78.6 8.0 70. 7.9 76.8 8. 68.7 70. 7.0 80. 67.0 68. 7. 78. 6.6 6.0 69. 7. 8.9 60. 6. 68.8 S/T 0.9 0.88 0.7 0..00 0.9 0.7 0.6.00 0.9 0.76 0.7.00 0.97 0.79 0.9.00.00 0.8 0.6.00.00 0.8 0.6 T 0 6 0 6 0 6 0 6 0 6 0 8 kw.8.8..60..67.8 6.0.88 6.0 6.9 6.9 6.8 6. 6. 6.7 6. 6.6 6.77 6.99 6.6 6.78 7.00 7. HI PR 9 8 7 8 69 89 0 8 06 9 7 6 8 7 96 9 6 66 9 LO PR 0 7 8 6 6 8 0 9 7 7 7 6 7 6 60 70 MBh 69.9 7. 76. 8.6 68. 69.8 7.6 79.7 66.7 68. 7.8 77.8 6.0 66. 7.0 7.9 6.8 6. 67. 7. 7. 8. 6. 66.8 S/T 0.90 0.8 0.68 0. 0.9 0.87 0.7 0. 0.9 0.89 0.7 0. 0.98 0.9 0.7 0.6.00 0.96 0.78 0.8.00 0.96 0.78 0.9 T 0 6 7 7 7 6 9 kw...0.6..6.79.97.8.96 6. 6. 6. 6.6 6. 6.66 6.8 6. 6.7 6.9 6.9 6.7 6.9 7.7 HI PR 7 69 8 66 86 0 0 6 9 7 9 08 88 7 9 8 6 87 08 LO PR 09 6 6 9 7 9 8 6 0 6 6 8 68 MBh 6. 6.9 70. 7. 6.0 6. 68.8 7.6 6. 6.9 67. 7.8 60.0 6. 6. 70. 7.0 8. 6. 66.6.8.0 7.7 6.6 S/T 0.86 0.8 0.66 0.9 0.89 0.8 0.68 0. 0.9 0.86 0.70 0. 0.9 0.89 0.7 0. 0.98 0.9 0.7 0.6 0.99 0.9 0.76 0.7 T 7 7 7 6 7 7 0 6 kw.0..7..8.9.66.8.70.8 6.00 6.9.98 6. 6.0 6.0 6. 6. 6. 6.76 6. 6.7 6.77 6.99 HI PR 0 7 6 7 8 78 9 06 9 6 8 60 80 96 76 0 7 6 7 7 9 LO PR 06 0 9 9 8 6 9 8 6 8 8 0 6 8 60 0 00 MBh 7. 7.7 78. 8. 7.6 7.0 76. 8. 69.9 7. 7.6 79.6 68. 69. 7.8 77.6 6.7 66.0 69. 7.7 60.0 6. 6.0 68. S/T 0.98 0.9 0.86 0.7.00 0.98 0.89 0.7.00.00 0.9 0.7.00.00 0.9 0.8.00.00 0.98 0.8.00.00 0.98 0.8 T 0 0 0 0 8.9 kw...8.6.9.7.88 6..9 6.0 6. 6. 6. 6.6 6.6 6.8 6.8 6.6 6.8 7.0 6.69 6.8 7.06 7. HI PR 60 7 86.7 7 9 08.7 09 6.8 78 99 6.6 9 6 9 68.7 7 70 97 7.9 LO PR 8 9 7. 7 6.0 0 0.7 8 6 9 8. 6 6.9 9 8 6 7.6 MBh 7. 7. 7.9 8.0 69. 70.8 7. 79. 67.8 69. 7. 77. 66. 67. 70.6 7. 6.9 6. 67. 7.6 8. 9. 6. 66. S/T 0.9 0.9 0.8 0.7 0.97 0.9 0.8 0.7.00 0.96 0.87 0.7.00 0.99 0.90 0.7.00.00 0.9 0.8.00.00 0.9 0.8 T 6 6 6 6 6 6 6 6 9.8 kw.8.8..6..67.8 6.0.88 6.0 6.9 6. 6.8 6. 6. 6.7 6. 6.6 6.77 7.0 6.6 6.78 7.00 7. HI PR 9 8 7 8.8 69 89 0 8. 06 9 7 6. 8 7 96. 9 6. 66 9.8 LO PR 0 7 8.9 6.6 8 0 9. 7 7 6.7 6. 7 6 60 69.9 MBh 6.7 66.9 70. 7.8 6. 6. 68. 7.0 6.6 6.8 66.8 7. 6. 6. 6. 69.6 8.0 9. 6.9 66..7.8 7. 6. S/T 0.9 0.87 0.79 0.6 0.9 0.9 0.8 0.7 0.96 0.9 0.8 0.7 0.99 0.96 0.86 0.7.00 0.99 0.90 0.7.00.00 0.9 0.7 T 7 6 7 7 7 7 7 7 6 6 0. kw.06.6.....70.9.7.87 6.0 6. 6.0 6.6 6. 6.6 6.7 6. 6.6 6.8 6.8 6.6 6.8 7. HI PR 0 6 7. 6 80 96 08.9 96 9 7. 8 6 8 00. 80 09 0. 0 77 97. LO PR 07.8 0 9. 7 6.7.0 9 7 0 9. 6.8 IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AHRI Rating conditions kw = Total system power High and low pressures are measured at the liquid and suction service valves. Amps = outdoor unit amps (comp.fan) 8 www.daikinac.com SSDG
Expanded ooling Data 6 Tons ( Speed) Outdoor Ambient Temperature 6 7 8 9 0 Entering Indoor Wet Bulb Temperature IDB Airflow 9 6 67 7 9 6 67 7 9 6 67 7 9 6 67 7 9 6 67 7 9 6 67 7 70 0 99 MBh 67.6 70. 76.8 66.0 68. 7.0 6. 66.8 7. 6.9 6. 7. 9.8 6.9 67.9. 7. 6.9 S/T 0.7 0.60 0. 0.7 0.6 0. 0.77 0.6 0. 0.79 0.66 0.6 0.8 0.69 0.8 0.8 0.69 0.8 Delta T 8 8 6 8 6 8 6 8 6 7 KW.89.98....0..6.8.8.9 6. 6.0 6.6 6.6 6. 6.7 6.7 HI PR 8 6 9 79 9 9 7 6 8 77 06 9 7 9 7 LO PR 0 7 8 6 9 0 7 7 8 6 60 MBh 6.6 68.0 7. 6. 66. 7.8 6.6 6.9 7. 6. 6. 69. 8.0 60. 6.9.7.7 6.0 S/T 0.69 0.8 0.0 0.7 0.60 0. 0.7 0.6 0. 0.76 0.6 0. 0.79 0.66 0. 0.79 0.66 0.6 Delta T 9 6 9 6 9 6 9 6 9 6 7 KW.8.9.09.9.0.6.0.6.78.76.88 6.06.99 6. 6. 6.9 6. 6. HI PR 8 6 60 6 76 9 9 7 77 7 0 69 LO PR 09 6 7 0 7 9 6 6 0 6 8 MBh 6. 6.6 70.8 60.9 6. 69. 9. 6.6 67. 8.0 60. 6.9. 7. 6.6..9 8.0 S/T 0.66 0. 0.8 0.68 0.7 0.0 0.70 0.9 0. ` 0.7 0.6 0. 0.7 0.6 0. 0.76 0.6 0. Delta T 9 6 9 7 9 7 9 7 9 7 8 KW.78.87.0...7...69.67.79.97.90 6.0 6. 6.09 6. 6. HI PR 70 8 86 07 0 70 66 9 6 0 60 LO PR 07 0 7 6 9 7 0 7 0 99 MBh 68.8 70.8 76.6 8. 67. 69. 7.8 80. 6.6 67. 7. 78. 6.0 6.9 7. 76. 60.8 6.6 67.7 7.7 6. 8.0 6.7 67. S/T 0.8 0.7 0.6 0.6 0.8 0.76 0.8 0.7 0.87 0.78 0.9 0.8 0.90 0.8 0.6 0.9 0.9 0.8 0.6 0. 0.9 0.8 0.6 0. Delta T 9 6 9 6 9 6 9 6 9 6 9 8 0 KW.9.0.7..7.8..7.8.70.87 6.0.8.98 6.6 6. 6.09 6. 6. 6.6 6.9 6. 6.6 6.8 HI PR 6 76 6 8 97 0 97 0 8 9 6 8 0 8 0 79 99 LO PR 8 9 8 8 6 0 8 6 9 9 6 66 9 8 6 7 MBh 66.8 68.7 7. 79.8 6. 67. 7.7 78.0 6.7 6. 70.9 76. 6. 6.9 69. 7. 9.0 60.7 6.7 70.6.6 6. 60.9 6. S/T 0.78 0.70 0. 0. 0.8 0.7 0. 0. 0.8 0.7 0.6 0.6 0.86 0.77 0.8 0.7 0.89 0.80 0.60 0.9 0.90 0.8 0.6 0.9 Delta T 0 6 0 6 0 6 0 6 0 6 0 9 0 KW.89.98..8...0.66..6.8 6.00.8.9 6. 6.0 6.0 6.6 6.6 6.6 6. 6.7 6.7 6.78 HI PR 8 6 7 9 79 9 07 9 7 9 6 8 98 77 06 9 7 7 9 7 9 LO PR 0 7 8 6 6 9 0 0 7 8 7 6 8 6 60 70 MBh 6. 6. 70.7 7.9 6.9 6.8 69.0 7. 60. 6. 67. 7. 9.0 60.7 6.7 70.6 6.0 7.7 6. 67.0.9. 7.9 6. S/T 0.7 0.67 0. 0. 0.78 0.70 0. 0. 0.80 0.7 0. 0. 0.8 0.7 0.6 0.6 0.86 0.76 0.8 0.7 0.86 0.77 0.8 0.8 Delta T 0 7 0 7 7 7 0 7 9 6 KW.8.9.0.0.6.6..8.6.7.7.9.7.8 6.0 6.0.9 6.07 6.6 6. 6. 6.7 6.6 6.67 AMPS 0. 0.8.....9....8..9..6..7.0..0..8..8 HI PR 6 7 68 7 88 0 89 8 9 7 90 70 98 0 8 09 0 6 8 LO PR 08 8 6 8 7 0 9 6 7 67 IDB = Entering Indoor Dry Bulb Temperature LO PR Shaded area reflects AA (TVA) Rating conditions kw = Total system power High and low pressures are measured at the liquid and suction service valves. Amps = outdoor unit amps (comp.fan) SSDG www.daikinac.com 9
Expanded ooling Data 6 Tons ( Speed) (cont.) Outdoor Ambient Temperature 6 7 8 9 0 Entering Indoor Wet Bulb Temperature IDB Airflow 9 6 67 7 9 6 67 7 9 6 67 7 9 6 67 7 9 6 67 7 9 6 67 7 80 0 99 MBh 70.0 7. 76. 8.7 68. 69.8 7.6 79.8 66.7 68. 7.8 77.9 6. 66. 7. 76.0 6.8 6. 67. 7. 7. 8. 6. 66.9 S/T 0.90 0.8 0.69 0. 0.9 0.88 0.7 0. 0.96 0.90 0.7 0..00 0.9 0.7 0.6.00 0.96 0.78 0.9.00 0.97 0.79 0.9 Delta T 9 9 9 6 0 6 9 8 KW.96.06..6...8.7.6.7.9 6.0.90 6.0 6. 6.0 6. 6.6 6.6 6.66 6. 6.7 6.67 6.89 HI PR 68 79 6 8 00 00 6 68 89 06 8 7 6 8 8 0 LO PR 0 0 9 9 6 8 7 0 8 0 60 6 8 68 0 9 6 7 MBh 67.9 69. 7. 79. 66. 67.8 7. 77. 6.8 66. 70.7 7.6 6. 6.6 69.0 7.8 60.0 6. 6.6 70..6 6.8 60.7 6.9 S/T 0.86 0.8 0.66 0.9 0.89 0.8 0.68 0. 0.9 0.86 0.70 0. 0.9 0.88 0.7 0. 0.98 0.9 0.7 0.6 0.99 0.9 0.7 0.6 Delta T 0 6 0 6 0 6 0 6 0 6 9 KW.9.0.7..7.8..7.8.70.87 6.0.8.98 6.6 6. 6.09 6. 6. 6.6 6.9 6. 6.6 6.8 HI PR 6 76 6 8 97 0 97 0 8 9 6 8 0 8 0 79 99 LO PR 8 9 8 8 6 0 8 6 9 9 6 66 9 8 6 7 MBh 6. 66.0 70. 7. 6.0 6. 68.8 7.6 6. 6.9 67. 7.8 60.0 6. 6.6 70. 7.0 8. 6. 66.6.8.0 7.7 6.7 S/T 0.8 0.77 0.6 0.7 0.8 0.80 0.6 0.9 0.88 0.8 0.67 0.0 0.90 0.8 0.69 0. 0.9 0.88 0.7 0. 0.9 0.89 0.7 0. Delta T 0 6 7 7 7 6 9 KW.8.9.09..9.0.6.6.0.6.78.96.76.88 6.06 6..99 6. 6. 6.0 6.9 6. 6. 6.7 HI PR 8 6 60 7 6 76 9 0 9 6 7 77 9 7 0 69 89 LO PR 09 6 7 0 7 9 8 6 6 6 0 6 6 8 69 8 0 99 MBh 7. 7.6 76.0 8. 69. 70.9 7. 79. 67.9 69. 7. 77. 66. 67. 70.7 7. 6.9 6. 67. 7.7 8. 9. 6. 66. S/T 0.9 0.9 0.8 0.67 0.98 0.9 0.8 0.69.00 0.97 0.87 0.7.00.00 0.90 0.7.00.00 0.9 0.76.00.00 0.9 0.77 Delta T 0 0 0 0 0 9 KW.00.09..0..6.6.80.67.78.96 6..9 6.07 6.6 6.6 6.8 6. 6. 6.7 6.9 6. 6.7 6.9 HI PR 8 6 70 8 67 87 0 6 0 7 60 6 7 9 0 89 8 6 0 6 88 09 LO PR 0 0 8 9 8 9 6 7 6 9 70 6 7 MBh 69. 70. 7.8 78.7 67. 68.8 7. 76.9 6.9 67. 70. 7. 6. 6.6 68.7 7. 6. 6. 6. 69.6 6.6 7.7 60. 6. S/T 0.90 0.87 0.79 0.6 0.9 0.90 0.8 0.66 0.96 0.9 0.8 0.68 0.99 0.9 0.86 0.70.00 0.99 0.89 0.7.00.00 0.90 0.7 Delta T 0 6 6 6 6 9 KW.96.06..6...8.7.6.7.9 6.0.90 6.0 6. 6.0 6. 6.6 6.6 6.66 6. 6.7 6.67 6.89 HI PR 68 79 6 8 00 00 6 68 89 06 8 7 6 8 8 0 LO PR 0 0 9 9 6 8 7 0 8 0 60 6 8 68 0 9 6 7 MBh 6.7 66.9 70. 7.8 6. 6. 68. 7. 6.6 6.8 66.9 7. 6. 6. 6. 69.6 8.0 9. 6.0 66..8.8 7. 6. S/T 0.86 0.8 0.7 0.6 0.89 0.86 0.78 0.6 0.9 0.89 0.80 0.6 0.9 0.9 0.8 0.67 0.98 0.9 0.86 0.69 0.99 0.96 0.86 0.70 Delta T 6 6 7 6 7 6 7 6 6 6 0 KW.89.98..8...0.66..6.8 6.00.8.9 6. 6.0 6.0 6.6 6.6 6.6 6. 6.7 6.7 6.78 HI PR 8 6 7 9 79 9 07 9 7 9 6 8 97 77 06 9 7 7 9 7 9 LO PR 0 7 8 6 6 9 0 0 7 7 7 6 8 6 60 70 IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AHRI Rating conditions kw = Total system power High and low pressures are measured at the liquid and suction service valves. Amps = outdoor unit amps (comp.fan) 0 www.daikinac.com SSDG
Airflow Data 6 Tons ESP (In W..) DG07 Standard Belt Drive and TwoSpeed Standard Belt Drive At High Speed Horizontal 0 Turns Turn Turns Turns Turns Turns FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP 0. 79.8 7 0.96 0 0.79 0. 680..06 6 0.8 6 0.68 0.6 6. 98.0 06 0.9 09 0.7 890 0.7 0.8 70.7 86.0 6 0.97 076 0.8. 7.07 00 0.8..6 08 0.9 ESP (In W..) DG07 Standard Belt Drive and TwoSpeed Standard Belt Drive At High Speed Down Shot 0 Turns Turn Turns Turns Turns Turns FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP 0. 6.8 86.0 0.8 0.68 0. 76. 96.8 76.09 7 0.9 9 0.7 98 0.9 0.6 60..8.00 070 0.80 898 0.6 0.8.9.06 068 0.86 868 0.7 8.7 00 0.9 806 0.7. 0.0 ESP (In W..) High Static Belt Drive Horizontal 0 Turns Turn Turns Turns Turns Turns FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP 0.6 677.9 86.07 0.8 690. 9.0 6 0.9 70.60 7.7 6.0 97 0.79. 78.7 8.. 970 0.87. 797.87 6.9 7.7 0 0.99.6 6.67.0 0..8.0 07. 7. ESP (In W..) High Static Belt Drive Down Shot 0 Turns Turn Turns Turns Turns Turns FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP 0.6 79.6 7.7 07. 0 0.96 0.8 77.76 68. 07. 6.0 0 0.8 8.89 660.67 07.6 9. 0 0.9. 696.79 97. 8. 977 0.98..9 6. 0.0.6 6. 0.0.8 069.0 Note: Tables represent dry coil without filter; to compensate for filter, add 0.08" to measured E.S.P. Air Flow Pressure Drop of Down Flow Economizer Airflow Pressure Drop of Downflow Economizer for to 6 Ton Rofftop Units (00% Return Air) SF, 800 000 00 00 600 800 000 00 00 600 800 in WG 0.0 0.0 0.0 0.07 0.09 0. 0. 0.7 0. 0. 0.8 SSDG www.daikinac.com
rankcase Heater, High Efficiency MERV Air Filter Option High Efficiency MERV Air Filter Option 0.0 Flanders Pre Pleat M Air Velocity vs Resistance (Test Size: " x " x " High apacity) 0. 0.0 " Deep Resistance (in. w.g.) 0. 0.0 0. 0.0 0. 0.0 0.0 0.00 0 00 00 00 00 00 600 700 Air Velocity (FPM) Tonnage: Filter Nominal Size: Part Number: Order QTY: x x 060L000 x 0 x 060L000, 6, 7. 6 x 0 x 060L000 7.(HP), 8., 0 6 X X 060L0006. 0 x x 060L000, 0 0 x x 060L000 6 0 X 0 X 060L000 8 rankcase Heater Selection Table ompressor Voltage rankcase ZP/ZPS ompressor Diameter 0V 60V 7V Heater Watts 6." 06R0000S 06R000S 06R000S 0 98 6.8/7." 00L0007S 00L0008S 00L0009S 70 07 9. 00L0000S 00L000S 00L000S 90 D*,DT* & DS* Tonnage ompressor Voltage 0V 60V 7V rankcase Heater Watts Ton 06R0000S 06R000S 06R000S 0 Ton. Ton 00L0007S 00L0008S 00L0009S 70 0 Ton** 00L0007S 00L0008S 00L0009S 70 Ton 00L0000S 00L000S 00L000S 90 *Includes,G&H models. **If ompressor Diameter is 9. then use Ton rankcase heaters. www.daikinac.com SSDG
Electrical Data 6 ton Model Number Electrical Rating ompressor ircuit ompressor ircuit Outdoor Fan Motor Indoor Fan Motor Optional Powered onvienience Outlet Power Supply RLA LRA RLA LRA QTY HP FLA Type HP FLA FLA MA MOP DG07XXXB 08/060 9.0.0 0..00 Standard Belt Drive.0.80 0.6 / 0.6 / 7. / 6. 7.8 / 7. 0 / 0 DG07XXXH 08/060 9.0.0 0..00 High Static Belt Drive.00 6.0. /. 0 / 0 7. / 6. 9. / 8.7 0 / 0 DG07XXXV 08/060 7.6 6.0 0..00 Standard Belt Drive (High Speed).00 6.00 0.0 / 0.0 / 7. / 6. 7. / 6. 0 / 0 DG07XXXB 6060 9.7 6.0 0. 0.8 Standard Belt Drive.0.0.. 8.7 DG07XXXH 6060 9.7 6.0 0. 0.8 High Static Belt Drive.00.00 6.0. 9. DG07XXXV 6060 8. 66. 0. 0.8 Standard Belt Drive (High Speed).00.90. 0. 7.6 DG07XXX7B 760 7. 0.0 0. 0.90 Standard Belt Drive.0.0..6. 0 DG07XXX7H 760 7. 0.0 0. 0.90 High Static Belt Drive.00.0.7 0.6. 0 DG07XXX7V 760 6.. 0. 0.90 Standard Belt Drive (High Speed).00.0..6.8 0 SSDG www.daikinac.com
Dimensions TOP VIEW.6.80 FLUE/VENT OUTLET OMBUSTION AIR INLET (GAS UNITS) GAS LINE ENTRANE 7.9 FRONT VIEW ALL DIMENSIONS GIVEN ARE IN INHES ALL DIMENSIONS AND SPEIFIATIONS ARE SUBJET TO HANGE WITHOUT NOTIE SUPPLY AIR DUT.000.7 0.060 6.96 DG07*** 6 TON OMMERIAL.0.000 7.6 7.000 ONDENSATE DRAIN OUTLET LIFTING SHAKLE HOLES BOTH SIDES AND ENDS 8.96 FK HOLES BOTH SIDES AND BOTH ENDS 0.8 RIGHT END VIEW RETURN AIR DUT www.daikinac.com SSDG
Dimensions (cont.) 9.70.0.000 ONDENSATE DRAIN BOTTOM EXIT MOD TON GAS, HT M TON GAS, HT M TON GAS, HT M 6 TON GAS, HT M SUPPLY AIR DUT 7.000 8...000 0.90 6.9.8.000 RETURN AIR DUT 7.06 BASE PAN VIEW (VIEWED FROM TOP) 7.98 LINE WIRE ENTRANE 0. 0.0.80 8. TSTAT WIRE ENTRANE.87 0.7 LEFT END VIEW SSDG www.daikinac.com
Unit learances Maintain an adequate clearance around the unit for safety, service, maintenance, and proper unit operation. Leave a total clearance of 7 on the main control panel side of the unit for possible removal of fan shaft, coil, electric heat, and gas furnace. Leave a clearance of 8 on all other sides of the unit for possible compressor removal or service access, and to ensure proper ventilation and condenser airflow. Do not install the unit Beneath any obstruction. Install the unit away from all building exhausts to inhibit ingestion of exhaust air into the unit s freshair intake. Electrical Entrance Locations HighVoltage Entrance (Remove Plug) LowVoltage Entrance ⅜ ½ Dia. 0¼ Power Thru the urb LowVoltage Entrance 7½ 7½ orner & enterofgravity Locations Unit Weights 6Ton Weights 0 ondenser oil Return Evaporator oil Supply orner Weight (A) 0 orner Weight (B) orner Weight () 0 orner Weight (D) Unit Shipping Weight 7 Unit Operating Weight 690 ompressor 7 Note: Weights are calculated without accessories installed. 6 www.daikinac.com SSDG
Roof urb Installation Rigging Provisions for forks have been included in the unit base frame. No other fork locations are approved. Unit must be lifted by the four lifting holes located at the base frame corners. Lifting cables should be attached to the unit with shackles. The distance between the crane hook and the top of the unit must not be less than 60. Two spreader bars must span over the unit to prevent damage to the cabinet by the lift cables. Spreader bars must be of sufficient length so that cables do not come in contact with the unit during transport. Remove wood struts mounted beneath unit base frame before setting unit on roof curb. These struts are intended to protect unit base frame from fork lift damage. To remove the struts, extract the sheet metal retainers and pull the struts through the base of the unit. Refer to rigging label on the unit. Important: If using bottom discharge with roof curb, ductwork should be attached to the curb prior to installing the unit. Ductwork dimensions are shown in Roof urb Installation Instructions Manual. Refer to the Roof urb Installation Instructions for proper curb installation. urbing must be installed in compliance with the National Roofing ontractors Association Manual. Lower unit carefully onto roof mounting curb. While rigging the unit, the center of gravity will cause the condenser end to be lower than the supply air end. Bring condenser end of unit into alignment with the curb. With condenser end of the unit resting on curb member and using curb as a fulcrum, lower opposite end of the unit until entire unit is seated on the curb. When a rectangular cantilever curb is used, take care to center the unit. heck for proper alignment and orientation of supply and return openings with duct. To assist in determining rigging requirements, unit weights are shown below. urb installations must comply with local codes and should follow the established guidelines of the National Roofing ontractors Association. Proper unit installation requires that the roof curb be firmly and permanently attached to the roof structure. heck for adequate fastening method prior to setting the unit on the curb. Full perimeter roof curbs are available from the factory and are shipped unassembled. The installing contractor is responsible for field assembly, squaring, leveling, and mounting on the roof structure. All required hardware necessary for the assembly of the sheet metal curb is included in the curb accessory package. Determine sufficient structural support before locating and mounting the curb and package unit. Ductwork must be constructed using industry guidelines. The ductwork must be placed into the roof curb before mounting the package unit. Our full perimeter curbs include duct connection frames to be assembled with the curb. antileveredtype curbs are not available from the factory. ontractor furnishes curb insulation, cant strips, flashing, and general roofing material. Support curbs on parallel sides with roof members. To prevent damage to the unit, the roof members cannot penetrate supply and return duct openings. Note: The unit and curb accessories are designed to allow vertical duct installation before unit placement. Duct installation after unit placement is not recommended. See the manual shipped with the roof curb for assembly and installation instructions. D View Insulated Panels Top View 70¾ 0¼ x 0 Supply Opening ⅝ x Return Opening 6 ¾ ⅜ SSDG www.daikinac.com 7
8 6 Wiring Diagram DG 6 Tons (0V, ThreePhase, Belt Drive) T T T T T T OMP L L F B NOTE II 6 PS 8 EON 9 7 0 LPS HPS 9 8 7 6 R S S W W G Y Y PLF NOTE TO THERMOSTAT TERMINAL OK INSTALLER/SERVIAN THE STATUS LIGHT ON THE FURNAE ONTROL MAY BE USED AS A GUIDE TO TROUESHOOTING THIS APPLIANE. STATUS LIGHT ODES ARE AS FOLLOWS: STATUS LIGHT ON OFF INK T INKS INKS INKS INKS 6 INKS H ALS PS RS M NOTE PLF EQUIP. STATUS NMAL OPERATION NO POWER INTERNAL ONTROL ITION FAILURE OPEN ROLLOUT SWITH OPEN AUX. LIMIT SWITH PRESSURE SWITH OPEN PRESSURE SWITH LOSED WITHOUT INDUER ON OPEN LIMIT SWITH FALSE FLAME SENSED OMPRESS OUTT DELAY 6 W. R. (ALT.) HONEYWELL GAS VALVE GAS VALVE MV MV VM T T OMP T D F SUPPLY VOLTAGE 080//60 B T T T LS ALS T L SMOKE/FIRE DETET REPLAES JUMPER WIRE T M B B VM TR NOTE RS 9 8 7 SSYY B LS HEK HEK INT POWER HEK FUSE ON ONTROL REPLAE ONTROL GAS FLOW GAS PRESSURE GAS VALVE FLAME SENS FLAME ROLLOUT BAD SWITH AUX. LIMIT OPEN HEK PRESSURE SWITH HEK PRESSURE SWITH MAIN LIMIT OPEN BAD SWITH STIKING GAS VALVE MIN. OMP. ANTIYLE TIMER R W W G TO THERMOSTAT II L L DI 08 0 TR V EON 7 9 SEE NOTE 6 UNUSED HEAT OOL 0 SEE NOTE OMPONENT LEGEND ALS AUXILIARY LIMIT SWITH B OWER ONTAT OMP OMPRESS M ONDENSER MOT ONTAT EVAPAT MOT F FUSE F FAN APAIT FLAME SENS EQUIPMENT OUND GAS VALVE HPS HIGH PRESSURE SWITH I INDO OWER RELAY II INTEATED ITION ONTROL IT LPS LOW PRESSURE SWITH LS LIMIT SWITH PLF FALE PLUG/ONNET PS PRESSURE SWITH RS ROLLOUT SWITH TB TERMINAL OK (V SAL) TR TRANSFMER VM VENT MOT VENT MOT RELAY NOTES. REPLAENT WIRE MUST BE THE SAME SIZE AND TYPE OF INSULATION AS IGINAL. (USE OPPER ONDUT ONLY).. AESSY EONOMIZER PLUG ADJAENT TO OWER HOUSING IN RETURN AIR OMPARTMENT. ROVE MALE PLUG AND ATTAH FALE PLUG TO THE EONOMIZER AESSY.. AND ON II ONTROL IS V INT.. USE OPPER ONDUTS ONLY. USE NE LASS WIRE.. F 08 VOLT TRANSFMER OPERATION, MOVE AK WIRE FROM TERMINAL TO TERMINAL ON TRANSFMER. 6. F LOW STAGE OPERATION ONLY, ROVE ITE JUMPER. F STAGE OPERATION, ROVE JUMPER AND ONNET W TO W ON THERMOSTAT. SEE UNIT RATING PLATE F TYPE AND SIZE OF OVER URRENT PROTETION 080//60 00L00A POWER SUPPLY 080//60 SEE NOTE II / / F LPS HPS FATY WIRING LINE VOLTAGE LOW VOLTAGE OPTIONAL HIGH VOLTAGE FIELD WIRING HIGH VOLTAGE LOW VOLTAGE WIRE ODE AK UE OWN EEN ANGE PINK RPLE RED ITE YELLOW / UE WITH PINK STRIP / YELLOW WITH PINK STRIP THERMOSTAT FIELD WIRING NO EONOMIZER W W G G R R Y Y Y TB STAT WITH EONOMIZER OPTION W G R Y Y STAT TB STAGE OOLING W W G G R R Y Y Y Y TB W G R Y STAT High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. Wiring is subject to change. Always refer to the wiring diagram on the Warning unit for the most uptodate wiring. 8 www.daikinac.com SSDG
8 6 Wiring Diagram DG 6 Ton (60V/ 7V, ThreePhase, Belt Drive) T T T T T T OMP L POWER SUPPLY 60//60 7//60 SEE NOTE M F B NOTE II 6 PS 8 EON 9 7 0 LPS HPS 9 8 7 6 PLF R S S W W G Y Y NOTE TO THERMOSTAT TERMINAL OK INSTALLER/SERVIAN THE STATUS LIGHT ON THE FURNAE ONTROL MAY BE USED AS A GUIDE TO TROUESHOOTING THIS APPLIANE. STATUS LIGHT ODES ARE AS FOLLOWS: STATUS LIGHT ON OFF INK T INKS INKS INKS INKS 6 INKS H ALS F PS NOTE PLF RS 6 9 8 7 W. R. (ALT.) HONEYWELL GAS VALVE GAS VALVE MV MV SS YY R W W G SMOKE/FIRE DETET VM REPLAES JUMPER WIRE TO THERMOSTAT SUPPLY VOLTAGE 607//60 T T T OMP T D B T T T EQUIP. STATUS NMAL OPERATION NO POWER INTERNAL ONTROL ITION FAILURE OPEN ROLLOUT SWITH OPEN AUX. LIMIT SWITH PRESSURE SWITH OPEN PRESSURE SWITH LOSED WITHOUT INDUER ON OPEN LIMIT SWITH FALSE FLAME SENSED OMPRESS OUTT DELAY LS ALS L VM TR RS T M B B B NOTE LS II HEK HEK INT POWER HEK FUSE ON ONTROL REPLAE ONTROL GAS FLOW GAS PRESSURE GAS VALVE FLAME SENS FLAME ROLLOUT BAD SWITH AUX. LIMIT OPEN HEK PRESSURE SWITH HEK PRESSURE SWITH MAIN LIMIT OPEN BAD SWITH STIKING GAS VALVE MIN. OMP. ANTIYLE TIMER L L 60 7 OMPONENT LEGEND ALS AUXILLARY LIMIT SWITH B OWER ONTAT OMP OMPRESS M ONDENSER MOT ONTAT EVAPAT MOT F FUSE F FAN APAIT FLAME SENS EQUIPMENT OUND GAS VALVE HPS HIGH PRESSURE SWITH I INDO OWER RELAY II INTEATED ITION ONTROL IT LPS LOW PRESSURE SWITH LS LIMIT SWITH PLF FALE PLUG/ONNET PS PRESSURE SWITH RS ROLLOUT SWITH TB TERMINAL OK (V SAL) TR TRANSFMER VM VENT MOT VENT MOT RELAY NOTES DI TR V EON 7 9 SEE NOTE UNUSED HEAT OOL 0 SEE NOTE 60/7 TR 0. REPLAENT WIRE MUST BE THE SAME SIZE AND TYPE OF INSULATION AS IGINAL. (USE OPPER ONDUT ONLY).. AESSY EONOMIZER PLUG ADJAENT TO OWER HOUSING IN RETURN AIR OMPARTMENT. ROVE MALE PLUG AND ATTAH FALE PLUG TO THE EONOMIZER AESSY.. AND ON II ONTROL IS V INT.. USE OPPER ONDUTS ONLY. USE NE LASS WIRE.. F LOW STAGE OPERATION ONLY, ROVE ITE JUMPER. F STAGE OPERATION, ROVE JUMPER AND ONNET W TO W ON THERMOSTAT. SEE UNIT RATING PLATE F TYPE AND SIZE OF OVER URRENT PROTETION. 607//60 00L00A / / II F LPS HPS FATY WIRING LINE VOLTAGE LOW VOLTAGE OPTIONAL HIGH VOLTAGE FIELD WIRING HIGH VOLTAGE LOW VOLTAGE AK UE OWN EEN ANGE PINK RPLE RED ITE YELLOW / UE WITH PINK STRIP / YELLOW WITH PINK STRIP THERMOSTAT FIELD WIRING NO EONOMIZER W G R Y Y TB STAT WITH EONOMIZER OPTION W G R Y Y TB STAGE OOLING W G R Y Y TB WIRE ODE W G R Y W G R Y STAT W G R Y Y STAT High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. Wiring is subject to change. Always refer to the wiring diagram on the Warning unit for the most uptodate wiring. SSDG www.daikinac.com 9
ONTROLS DIAAM DG07 SPEED STAGE OMP Wiring Diagram DG ontrol Diagram DG07 Speed (All Voltages) TB LASS FIELD ONTROL WIRING TR SUPPLY (LINE) VOLTAGE S S R G W W Y Y O VA ALS RS II LS 7 8 9 0 7 G 8 PS OUT 9 R 0 W OMP IN OMP OUT A 6 P OOL FAN HEAT FAN SPEEDUP V OM LMT OUT LMT IN PS IN 6 0 0 D 6 GY GY PS GY LOW OM HIGH / LPS / 6 6 B B / HPS S / EON PLF 6 7 8 9 EON SHRT PLM 6 7 8 9 G EON PLM 6 7 8 9 OPTIONAL EONOMIZER MAT AUXI MAT O OAT E OAT EXH SBUS AUXO SBUS 6 YI IAQ 0 YO IAQ OM YI IAQ V YO AT OM AT V 6 R MAS t ENTH EON AT SBUS SBUS VOM VPWR OPTIONAL SMOKE DETET 6 6 7 8 8 7 V A/D 9 0 AUX A AUX B SENS SENS Y Y R B Y Y R B Y Y R B Y Y R B SEN SEN. REPLAENT WIRE MUST BE SAME SIZE AND TYPE OF INSULATION AS IGINAL (USE OPPER ONDUTS ONLY). IF OPTIONAL EONOMIZER IS INSTALLED, ROVE EON SHRT PLM AND ONNET EON PLM TO EON PLF. EN SPEEDUP PINS ARE SHTED, THE OMPRESS DELAY IS BYPASSED; BYPASS F TESTING/TROUESHOOTING ONLY ONNETIONS SHOWN ARE F STAGE HEAT OPERATION. EN STAGE OPERATION IS REQIRED ROVE JUMPER WIRE ONNETING W TO W ON TB. IF OPTIONAL SMOKE DETET(S) ARE INSTALLED, ROVE JUMPER WIRE ONNETING S TO S ON TB. WIRE ONNETIONS FROM AESSY KIT: ONNET WIRE TO TBS. ONNET WIRE TO TBS. ONNET TO TB (V OM). 6 II FAN OFFDELAY: OOL OFFDELAY IS 60 SEONDS AFTER OOL FAN ALL IS ROVED HEAT OFFDELAY IS SELETAE, A MOVAE JUMPER IS PROVIDED; 0,, 0 SEOND DELAY MAY BE SELETED. THE FATY SETTING IS 0 SE 00L0969A Wiring is subject to change. Always refer to the wiring diagram on the unit for the most uptodate wiring. Warning High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. 0 www.daikinac.com SSDG
Wiring Diagram DG Power Diagram DG07 Speed (0v) LINE VOLTAGE L POWER DIAAM DG07*** SPEED STAGE OMP FATY WIRING HIGH VOLTAGE OPTIONAL HIGH VOLTAGE LOW VOLTAGE ALS B H OMP OMPONENT LEGEND AUXILLARY LIMIT SWITH OWER ONTAT OWER RELAY OMPRESS ONTAT RANK ASE HEATER OMPRESS M ONDENSER MOT FIELD WIRING M MR ONDENSER MOT ONTAT ONDENSER MOT RELAY HIGH VOLTAGE LOW VOLTAGE S EON OMPRESS ND STAGE SOLENOID EONOMIZER EVAPAT MOT T T L T B T T L T B T T L T GY F GY () () () T T OMP T M 6 STATUS LIGHT ON OFF INK INKS INKS INKS WIRE ODE AK UE OWN EEN GY AY ANGE PINK RPLE RED ITE YELLOW / UE/ PINK STRIPE / YELLOW/ PINK STRIPE II DIAGNOSTI INK ODES EQUIPMENT STATUS NMAL OPERATION NO POWER INTERNAL ONTROL ITION FAILURE OPEN ROLLOUT SWITH OPEN AUX LIMIT SWITH PRESSURE SWITH OPEN PRESSURE SWITH LOSED WITHOUT INDUER ON OPEN LIMIT SWITH F7 HPS II LPS LS PLF PLM RS TB TB TR TR VM HEK HEK INT POWER HEK FUSE ON ONTROL REPLAE ONTROL GAS FLOW GAS PRESSURE GAS VALVE FLAME SENSER FLAME ROLLOUT BAD SWITH AUX.LIMIT OPEN HEK PRESSURE SWITH HEK PRESSURE SWITH MAIN LIMIT OPEN BAD SWITH FLAME SENS II V POWER FUSE EQUPIMENT OUND GAS VALVE HIGH PRESSURE SWITH INTEATED ITION ONTROL IT LOW PRESSURE SWITH LIMIT SWITH PLUG / ONNET, FALE PLUG / ONNET, MALE ROLLOUT SWITH TERMINAL OK, LOW VOLTAGE TERMINAL OK, LOW VOLTAGE TRANSFMER, ONTROLS (LINE VOLTAGE / VA) TRANSFMER, PWR VENT MOT (LINE VOLTAGE / 0VA) VENT MOT VENT MOT RELAY THERMOSTAT ONNETIONS THERMOSTAT IN / OUT VAPWR (INT) VA OM (INT) FAN ALL (OUTT) ST STAGE HEAT ALL (OUTT) ND STAGE HEAT ALL (OUTT) ST STAGE OOL ALL (OUTT) TB ONNETION R G W W Y VM INKS 6 INKS FALSE FLAME SENSED OMPRESS OUTT DELAY STIKING GAS VALVE MIN. OMP. ANTIYLE TIMER ND STAGE OOL ALL (OUTT) Y V NTL VOLTAGE II TR, LINE VOLTAGE NOTES:. REPLAENT WIRE MUST BE SAME SIZE AND TYPE OF INSULATION AS IGINAL (USE OPPER ONDUTS ONLY). UNIT TERMINALS ARE NOT DESED F OTHER ONDUTS THE USE OF OTHER TYPE ONDUTS MAY AUSE DAMAGE TO THE UNIT THE ONTROL TRANSFMER HAS MULTIPLE HIGH VOLTAGE TAPS. ENSURE WIRE ONNETIONS ARE RET F UNIT SUPPLY VOLTAGE RATING 08/0V SUPPLY POWER UNITS ARE FATY ONNETED TO THE ONTROL TRANSFMER 0V TAP. MOVE WIRE ONNETION FROM 0V TAP TO 08V TAP EN 08V POWER SUPPLY IS USED. SEE ONTROL DIAAM F ONTROL TRANSFMER LOW VOLTAGE ONNETIONS. SEE AESSY KIT LITERATURE F OPTIONAL ONVENIENE OUTLET WIRING DIAAM. 6 SPEED EVAPAT MOT: AK LEADS F HIGH SPEED OPERATION, AND ITE / UE / ANGE LEADS F LOW SPEED OPERATION. 00L097A Wiring is subject to change. Always refer to the wiring diagram on the unit for the most uptodate wiring. Warning High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. SSDG www.daikinac.com
Wiring Diagram DG Power Diagram DG07 Speed (60/7v) LINE VOLTAGE L POWER DIAAM DG07***(/7) SPEED STAGE OMP FATY WIRING HIGH VOLTAGE OPTIONAL HIGH VOLTAGE LOW VOLTAGE ALS B H OMP OMPONENT LEGEND AUXILLARY LIMIT SWITH OWER ONTAT OWER RELAY OMPRESS ONTAT RANK ASE HEATER OMPRESS M ONDENSER MOT FIELD WIRING M MR ONDENSER MOT ONTAT ONDENSER MOT RELAY HIGH VOLTAGE LOW VOLTAGE S EON OMPRESS ND STAGE SOLENOID EONOMIZER EVAPAT MOT 60V 7V TR 0V OM T T L T B T T L T B T T L T GY F GY () () () T T OMP T M STATUS LIGHT ON OFF INK INKS INKS INKS WIRE ODE AK UE OWN EEN GY AY ANGE PINK RPLE RED ITE YELLOW / UE/ PINK STRIPE / YELLOW/ PINK STRIPE II DIAGNOSTI INK ODES EQUIPMENT STATUS NMAL OPERATION NO POWER INTERNAL ONTROL ITION FAILURE OPEN ROLLOUT SWITH OPEN AUX LIMIT SWITH PRESSURE SWITH OPEN PRESSURE SWITH LOSED WITHOUT INDUER ON OPEN LIMIT SWITH F7 HPS II LPS LS PLF PLM RS TB TB TR TR VM HEK HEK INT POWER HEK FUSE ON ONTROL REPLAE ONTROL GAS FLOW GAS PRESSURE GAS VALVE FLAME SENSER FLAME ROLLOUT BAD SWITH AUX.LIMIT OPEN HEK PRESSURE SWITH HEK PRESSURE SWITH MAIN LIMIT OPEN BAD SWITH FLAME SENS II V POWER FUSE EQUPIMENT OUND GAS VALVE HIGH PRESSURE SWITH INTEATED ITION ONTROL IT LOW PRESSURE SWITH LIMIT SWITH PLUG / ONNET, FALE PLUG / ONNET, MALE ROLLOUT SWITH TERMINAL OK, LOW VOLTAGE TERMINAL OK, LOW VOLTAGE TRANSFMER, ONTROLS (LINE VOLTAGE / VA) TRANSFMER, PWR VENT MOT (LINE VOLTAGE / 0VA) VENT MOT VENT MOT RELAY THERMOSTAT ONNETIONS THERMOSTAT IN / OUT VAPWR (INT) VA OM (INT) FAN ALL (OUTT) ST STAGE HEAT ALL (OUTT) ND STAGE HEAT ALL (OUTT) ST STAGE OOL ALL (OUTT) TB ONNETION R G W W Y VM INKS 6 INKS FALSE FLAME SENSED OMPRESS OUTT DELAY STIKING GAS VALVE MIN. OMP. ANTIYLE TIMER ND STAGE OOL ALL (OUTT) Y V NTL VOLTAGE II TR LINE VOLTAGE NOTES:. REPLAENT WIRE MUST BE SAME SIZE AND TYPE OF INSULATION AS IGINAL (USE OPPER ONDUTS ONLY). UNIT TERMINALS ARE NOT DESED F OTHER ONDUTS THE USE OF OTHER TYPE ONDUTS MAY AUSE DAMAGE TO THE UNIT THE ONTROL TRANSFMER HAS MULTIPLE HIGH VOLTAGE TAPS. ENSURE WIRE ONNETIONS ARE RET F UNIT SUPPLY VOLTAGE RATING SEE ONTROL DIAAM F ONTROL TRANSFMER LOW VOLTAGE ONNETIONS. SEE AESSY KIT LITERATURE F OPTIONAL ONVENIENE OUTLET WIRING DIAAM. SPEED EVAPAT MOT: AK LEADS F HIGH SPEED OPERATION, AND ITE / UE / ANGE LEADS F LOW SPEED OPERATION. 00L097B Wiring is subject to change. Always refer to the wiring diagram on the unit for the most uptodate wiring. Warning High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. www.daikinac.com SSDG
WIRING DIAAMS F MODELS WITH DD ONTROLS For complete information and installation instructions for models with DD controls, see manual DKDDTGDXXX SSDG www.daikinac.com
Wiring Diagram with DD DG070 (080V//60) B*** SEE NOTE L T T 08 TR V 0 08 TR V VOUT D VA OM 0 T SMK/G B VM SEE NOTE T L OMP T POWER SUPPLY 080//60 SEE NOTE S PS ES XS V T T T T T DA TB T OM BI BI R R OM BI RL BI RL BI RL RL6 BI6 RL7 BI7 RL8 BI8 OM8 OM8 ALS BPSW M RF / RSS HPS LPS / / F / LS LDS II EON AO AI DAT HH AO 0 7 8 9 6 AI AI PS AO OAT AO AI EXF AI AI6 AI7 AI8 VA VOUT D DI 6 High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. Wiring is subject to change. Always refer to the wiring diagram on the Warning unit for the most uptodate wiring. RS OARH ALRM SEE NOTE A TP STPT OFET UNUSED HEAT OOL A SPTP (ALT.) HONEYWELL GAS VALVE MV MV W.R. GAS VALVE VA VOUT D SPRH EON AG O SEE NOTE 6 TB 00L00A 080//60 www.daikinac.com SSDG
Wiring Diagram with DD DG070 (080V//60) B*** OMPONENT LEGEND FATY WIRING WIRE ODE AK UE LINE VOLTAGE LOW VOLTAGE OPTIONAL HIGH VOLTAGE OPTIONAL LOW VOLTAGE FIELD WIRING HIGH VOLTAGE LOW VOLTAGE A AIL ALRM B B BHS BIL S BPSW OWN EEN ANGE PINK RPLE RED ITE YELLOW / UE WITH PINK STRIP / YELLOW WITH PINK STRIP SHATI SYMBOL FIELD OUND FIELD SPLIE ITER INTERNAL TO INTEATED ONTROL SWITH (TP) TERMINAL SEE UNIT RATING PLATE F TYPE AND SIZE OF OVER URRENT PROTETION R F F H HR HS M OM OMP S DFT EON ES EXF HH HPS LDS LPS OAT OARH PLF PS RF RL RSS RV SAT/DAT SMK/G SPTP SPRH TT TB TR XS D OUND F ANALOG SENSS ("AG" ON TB) 8 ANALOG INTS ALARM OWER ONTAT OWER ONTAT OWER HIGH SPEED 8 BINARY INTS OWER LOW SPEED OWER PROVING SWITH ONTAT OMPRESS ONTAT OMPRESS ONTAT RELAY ONDENS FAN ONDENS FAN ONTAT LOGGED FILTER SWITH RANKASE HEATER RANKASE HEATER RELAY RANKASE HEATER SWITH ONDENSER MOT OMMON ("" ON TB) OMPRESS OM AND SMOKE DETET DEFROST THERMOSTAT EONOMIZER EVAPAT MOT EON OM8 AND SMOKE DETET EXHAUST FAN EQUIPMENT OUND HOT GAS REHEAT HIGH PRESSURE SWITH LOAD SHEDDING LOW PRESSURE SWITH OUTDO AIR TPERATURE OUTDO AIR RELATIVE HUMIDITY FALE PLUG / ONNET HPS, LPS & SMOKE DETET RUN APAIT F ONDENSER FAN RELAY ROTE START STOP REVERSING VALVE OIL SUPPLY / DISHARGE AIR TPERATURE SMOKE ERGENY SHUTDOWN SPAE TPERATURE SPAE RELATIVE HUMIDITY MOT SPEED TAPS (DIRET DRIVEN MOT ONLY) TERMINAL OK (V SAL) TRANSFMER VA TRANSFMER & SMOKE DETET L SUPPLY VOLTAGE 080//60 T T OMP T F RF M VM B B B 080//60 080//60 TR TR V V SEE NOTE SMK/G BI BPSW BI OM HPS LPS BI R BI R DAT OAT OARH O SENS SP OFET TP OM SPRH EON PLF RSS LDS OM BI D BI6 D RL RL BI7 RL BI8 RL6 AI RL7 AI AI RL8 AI OM8 AO AI AO AI6 AI7 AO AO AI8 A VA NOTE D II H LS ALS B/S RS HH EXF ALRM PS 0 NOTE Wiring is subject to change. Always refer to the wiring diagram on the Warning unit for the most uptodate wiring. JUNTION OVERURRENT PROT. DEVIE PLUG ONNETION SWITH (PRESS.) NOTES:. REPLAENT WIRE MUST BE SAME SIZE AND TYPE INSULATION AS IGINAL (AT LEAST 0 ) USE OPPER ONDUT ONLY.. USE OPPER ONDUTS ONLY USE N.E.. LASS WIRE. EONOMIZER PLUG LOATED IN THE RETURN AIR OMPARTMENT. ROVE MALE PLUG AND ATTAH FALE PLUG TO THE EONOMIZER AESSY.. F 08 VOLT TRANSFMER OPERATION MOVE AK WIRE FROM TERMINAL TO TERMINAL ON TRANSFMER.. ROVE JUMPER IF SMOKE DETET ERGENY SHUTDOWN DEVIE IS INSTALLED. 6. RANKASE HEATER AND RANKASE HEATER SWITH FATY EQUIPPED EN REQUIRED. 080//60 00L0A High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. F 6 8 SSDG www.daikinac.com