GENT 1331 DOO COE INTTION INTUCTION WITH FOOWING M ET: JH, JH and JPH9 trength djustment From ize 1 Through 6. CUTION: FIUE TO INT O DJUT POPEY MY EUT IN INJUY O DMGE FO ITNCE, C GENT T 1800775477 or www.argentlock.com NOTE: These installation instructions to be used for product manufactured on or after Nov. 1, 013. Date Code: KU and shipped with arms shown on template pages. ee page 6 for date code location. Choose From 1 of 3 pplications JH rm (egular rm) ight hand (H) door shown. eft hand reverse (H) ee page JPH9 rm (egular rm) ight hand (H) door shown. eft hand reverse (H) ee page 3 JH rm (Top Jamb rm) ight hand (H) door shown. eft hand reverse (H) ee page 5 Doors should be hung on ball bearing or antifriction hinges. separate door stop is recommended. Door and frame must be properly reinforced. lways adjust spring power before adjusting control. djust closing time speed between 3 and 7 seconds from 90 to 0. Greater closing times may be required D. These door closers should NOT be installed on the exposed side (weather side) of exterior doors NOTE: For special applications a separate door and frame preparation template is packed with these instructions. Use this instruction sheet for installation sequence and closer adjustments only. Metal Wood elf Drilling crews Wood and Metal (Optional) leeve Nut and olt #7 1/40 3/16" * Pilot Hole equired For Wood drill 3/16 hole for Wood drill 7/3 Machine crews #7 Drill, 1/40 Tap Drill 9/3 thru from Closer ide 3/8 Drill other side Thru olt and Grommet Nut Drill 9/3 thru from Closer ide 3/8 Drill other ide ackcheck Valve atch Valve Power djustment haft rm ssembly Cover Insert Insert Cutouts Closer ody weep Valve offit dapter Plate et crew Main rm crew Pack 1331C Cover Full Cover tandard With 1331 eries Copyright 013 argent Manufacturing Company, an OY Group company. ll rights reserved. eproduction in whole or in part without the express written 8175
51/ (140) 13/4 (44) 1 13/8 (35) 11/4 (31.8) ight Hand hown 3/4 (19) 1 (304.8) Opening To 100 101 to 130 131 to *180 Dimension "" 71/ (191) 6 (15) 41/ (114) Door/Wall/Hardware/Jamb * conditions permitting NOTE: These installation instructions to be used for product manufactured on or after Nov. 1, 013. Date Code: KU hipped with arm as shown. Installation equence ight Hand Door hown D C eft Hand Nut Down et Hold Open Y 90 min. F 90 E 90 180 ee page 6 for spring and valve adjustments. Copyright 013 argent Manufacturing Company, an OY Group company. ll rights reserved. eproduction in whole or in part without the express written 8175
Door Opening To 10 * 11 to 180 91/ (41) 7 (178) 33/4 (95) 11/4 (3) ight Hand hown 7/16 (11) 3/4 (70) (50) 3/8 (10) 19.1 1/ (13) 1 C 31/ (89) Top of Door Frame abbet NOTE: These installation instructions to be used for product manufactured on or after Nov. 1, 013. Date Code: KU hipped with arm as shown. 3/4 (19) 1 (304.8) Frame offit Installation equence Install Closer and racket 3 ight hand door shown: djustment nut facing up. 11/ D C eft Hand ight Hand Up Down For eft hand door, djustment nut must face down. 3 Copyright 013 argent Manufacturing Company, an OY Group company. ll rights reserved. eproduction in whole or in part without the express written 8175
Close Valves 4 Preload Closer 5 ttach rm With 6 Proper Timing atch weep Place rm on pindle ight Hand Door or eft Hand Door Y Flat Flat Y otate emove rm from pindle Open Valves 7 8 9 ssemble rm et Hold Open weep atch Caution: Don't remove valves 11/ (38) Tighten rm crew ee page 6 for spring and valve adjustments. 4 Copyright 013 argent Manufacturing Company, an OY Group company. ll rights reserved. eproduction in whole or in part without the express written 8175
Y ight Hand hown 1 (304.8) 3/4 (19) Frame abbet 1/8 (54) Opening To 100 101 to 130 131 to *180 Dimension "" 71/ (191) 6 (15) 41/ (114) Door/Wall/Hardware/Jamb * conditions permitting 13/4 (44) 51/ (140) rm NOTE: These installation instructions to be used for product manufactured on or after Nov. 1, 013. Date Code: KU hipped with arm as shown. 1/ (13) eveal JH To 30 (76) JH 3/4 (70) to 63/4 (171.5) C eveal Installation equence et Hold Open E 90 ight Hand Door hown (Nut facing down) D 70 to 180 eft Hand Nut Up C F 5 Copyright 013 argent Manufacturing Company, an OY Group company. ll rights reserved. eproduction in whole or in part without the express written 8175
pring Power djust djustment Chart Number of Turns equired 1 DOO TYPE OF INT. * 3" (0.85M) MXIMUM DOO IE 36" (0.90M) 4" (1.00M) 48" (1.0M) 8100/8300/8500 EXTEIO INTEIO egular rm Top Jamb Parallel rm egular rm Top Jamb Parallel rm FU 360 TUN OF 5/16 POWE DJUTMENT WENCH 5 8 11 13 7 10 13 16 7 10 13 16 9 1 15 18 *0 FU (360 ) TUN MXIMUM VIE Closer is shipped set at mid range setting = 10 turns The closing force is adjustable from a size 1 to a size 6, as outlined in NI tandard 156.4. When these series of door closers are installed and adjusted to conform to D reduced opening force requirements (5 lbs max.) for interior doors, they may not have adequate closing force to reliably close and latch the door. Power adjustments charted on this page are recommended where possible, to ensure proper door control. y law the mericans with Disabilities ct (D) may require that door closer installation comply with accessability guidelines. Valve djustments 3 weep atch 4 ackcheck Caution: Don't completely close valve djust Closing peed Time to between 3 to 7 seconds from 90. Use of the door by handicapped, elderly or small children may require greater closing time. Cover crews 5 70 Mfg. Date: KU KU 10 COED 6 Copyright 013 argent Manufacturing Company, an OY Group company. ll rights reserved. eproduction in whole or in part without the express written 8175