September Australia Spring 2017

September Australia Spring 2017 $100 OFF YOUR SERVICE BALER MAINTENANCE THE HUMBLE TINE P3 Genuine Parts Promotion P6 We talk to the experts P9 Product Focus

ALWAYS INSIST ON GENUINE AGCO PARTS & LUBRICANTS GENUINE AGCO PARTS Replacing the genuine parts on your AGCO machine with genuine AGCO parts from your local dealer makes sense if you want to protect your investment. AGCO parts are designed specifically for your machine, are fully tested and meet the strict, specific standards for all AGCO machinery. This ensures that, not only are you getting the best quality for your machine, but they will fit perfectly, every time. Your local AGCO dealer is fully qualified to fit your genuine AGCO parts. They have the tools and the know-how to do the job right. GENUINE AGCO LUBRICANTS They don t get more genuine than genuine AGCO lubricants. Each formulation is painstakingly tested under monitored conditions to ensure they meet the stringent AGCO specifications. This means you can be sure you are using the right oil for your machine. Recently AGCO, Massey Ferguson and Fendt V-Trans was given CMS M1145 full approval from GIMA transmissions. AGCO Genuine Parts Promotion Get $100 off AGCO Genuine Parts on Your Next AGCO Service Be one of the 1st 100 customers to spend $1000 or more on AGCO Genuine Parts on your machine in a single invoice between the 18th of September and 30th November 2017* 1st 100 Entries Only V-Trans Plus was extensively tested over the last 12 months in a number of Massey Ferguson transmissions and test rigs, as well as being closely analysed and monitored in a laboratory setting, to ensure it met all requirements for Massey Ferguson Transmissions. You can be secure in the knowledge that our V-Trans Plus products are fully endorsed by AGCO worldwide and will protect your transmission in a range of environments and ambient temperatures. The advanced technology of V-trans 10W-40 contains carefully selected additives and base oils that ensure performance over your machine s life time. Always insist on genuine to guarantee the longevity of your equipment. Genuine Parts Genuine 12 month warranty Genuine peace of mind Only At Participating Dealers Terms & Conditions *Limited to the 1st 100 Entries. Must be on a Single Invoice from an AGCO Dealership where the value of Genuine AGCO Parts Exceeds $1000.00. AGCO Netwrap & Twine, Toys & Merchandise & AGCO HayBoss Not Included. Invoice must be dated between 18th of September and 30th November 2017. Invoice must be submitted to PartsMarketingANZ@agcocorp.com by the 1st of December 2017. $100 Voucher can be used for AGCO Genuine Parts on your next service Excluding Netwrap & Twine, AGCO HayBoss & Toys & Merchandise and must be redeemed at the AGCO Dealership it was won at by 1st June 2018. $100 Voucher will be sent out to winners by Post or Email by the 1st January 2018.Voucher must be redeemed in 1 single transaction. NSW Trade Promotion Permit No: LTPS/17/17727 2 September 2017 AGCOPARTSANZ.com.au September 2017 The Genuine Choice 3

BATTERIES Start with AGCO, everytime. } 4 3 1 QUALITY Longer } SERVICE } RECYCLING 2 6 5 1 32 4 3 5 4 6 Life Enhanced Power Reliable Performance Strong and Durable Improved Safety and Usability X Frame Grid Technology and Grid Protection Technology Enveloped separator for low electric resistance Advanced centre lug technology and cast on strap Sealed double lid with flame arrestor Integrated, reinforced container Magic Eye indicator displays state of charge DELIVERY PROMISE We aim to deliver in full, on time, every time. We appreciate that fleet downtime is not an option, this is reflected in our improved service promise. NATIONWIDE SUPPORT NETWORK An extensive supply network ensures exceptional service. FULLY MAINTAINED As part of our quality and service promise, we commit to keeping your batteries fully maintained so you can be assured that the battery that you receive is fully charged and in excellent condition. As of March 2017, the NSW Scrap Metal Industry Act, which makes it an offence to trade used batteries for cash sales. This will take into effect to regulate criminal activity affecting the scrap metal industry. The VIC Government has also announced similar legislation and we can expect other states to follow. Breach of this law may result in up to $11,000 in fines. AGCO Parts partnership with Enirgi Power Storage offers Australia s only EPA ISO14001 compliant used battery collection network. Their modern facilities recycle 97% of used lead acid batteries to the highest standard, whilst ensuring peace of mind. Simply return your used battery to your dealer, and we will ensure safe and compliant disposal. Please speak to your local AGCO dealer to find out more. 2 The name Walterscheid is synonymous with quality products. With years of experience behind them, you can rely on Walterscheid PTO shafts to get the job done. Get all your Walterscheid PTO shafts from your local AGCO dealer Remote locations and outdoor conditions can put your machinery to the test. Renold designs and manufactures chains to cope with this demanding environment. See your AGCO dealer today. 4 September 2017 AGCOPARTSANZ.com.au September 2017 The Genuine Choice 5

Baler Maintenance Tips From Hay Producers Tips From The Pro s The Annual Maintenance Checklist 20-plus checkpoints for round and/or square balers. Jesse Wilmot admits that he likes to sleep, even if some of his nights are pretty short. That s because Wilmot, and his business partner, Kelly Bonham, bale most of the hay on their Maysville, Oklahoma, operation at night. Hence, any problem with a baler delays sleep that much longer. That s one of the reasons Wilmot and Bonham try to keep their six Hesston by Massey Ferguson balers in top condition. We try to trade balers every few years to avoid any downtime, says Bonham, adding that a breakdown is a little less critical since they have several balers running at a time. But we still keep them as clean as possible using an air hose to regularly blow off dirt and debris. Wilmot says they also go through all the balers during the off-season to check bearings for wear, replace broken tines, adjust chains, etc. If they encounter any problems they can t repair themselves, they call their local AGCO dealer - Livingston Machinery Company in Chickasha, Oklahoma. We also get all our parts, including the twine, from Livingston Machinery so the equipment always performs the way it was designed to, Wilmot adds, noting that the partners also own two Hesston by Massey Ferguson WR9770 windrowers. We put about 3,000 bales through each of the 2190 machines on an annual basis and about 5,000 bales through the 3 X 3 models. So, they get fairly heavy use. Wilmot explains that during the haying season, they typically cut around 250 acres per day, and bale that same amount a day or two later. That s about all you can put up at a time, he says. So even though we have a number of balers, it can take both 2150s or all four 2190s, depending on what size of bale the customer wants. Original article published in myfarmlife.com the online extension of FarmLife Magazine. Find additional tips for making quality hay in the Hesston Guide to Quality Hay, available for free at myfarmlife.com. Thanks to the following for help with this list: Kevin Bermingham, service writer and 21-year veteran of the service department at Agri-Service in Twin Falls; Tim Brannon, owner of B & G Equipment in Paris, Tenn. We also received input from the many service technicians from Hesston by Massey Ferguson, as well as producers, such as Norris. Miscellaneous Check gearbox fluid levels and change as recommended in the operator s manual. Grease all grease nipples on wear points. Check with your dealer about any upgrades that appear on new balers that, in many cases, can be retrofitted. Ensure the correct genuine lubricant is used. Hoses and Hydraulics Change hydraulic-system filters, then run the machine to purge air from the system. Ensure that the auto-lube system is working properly. Refer to your owner s manual for the correct type of oil when filling the reservoir, as other oils will not cling to components as well. Also, make sure tubes leading to destination points haven t been cut, kinked or damaged. Examine all electric cables and hydraulic hoses for damage. Feeder Mechanisms Check to make sure all guards are intact and in place. Examine and replace any broken tines in the pickup, and make sure stripper plates haven t been bent or damaged. Check pickup cam track bearings for wear, and check cam track for dents or abnormal wear. Check the flighting and bearings on pickup feeder augers used on square balers and large round balers. Bale Chamber Examine hay moisture monitoring and preservation application systems to make sure they are operating properly. Remove any crop material wrapped on belt rollers or drive sprockets. Check all bearings, including those on drives, square baler plunger components and round baler forming belt rollers. Clean and lubricate all netwrap and twine components; grooves and areas of rust that can make the netwrap or twine stick. Ensure that all knives are sharp, including the plunger and knotter knives on square balers, and twine and/or netwrap knife on round balers. Belts and Chains Check all drive chains for wear and tension. If a chain is replaced, change out the sprockets as well, and vice versa. Check all drive belts for cracks, and ensure that idlers turn freely. On round balers, inspect belts for cracking and other wear. Also check the belt lacing, if applicable, to make sure they haven t pulled loose. Loosen belt tensioners so they are not sitting under full tension during the off-season. On the Outside Use air pressure to remove dirt, dust and hay debris. If this is followed by washing, great care should be taken to keep high pressure away from bearings and seals to prevent premature failure. Run the baler after washing for several minutes, then oil all chains and moving parts. Inspect tires for damage and excessive wear. Check all lug bolts to ensure they are tightened to specifications. 6 September 2017 AGCOPARTSANZ.com.au September 2017 The Genuine Choice 7

AGCO Netwrap & Twine Specially Engineered To Reduce Your Down Time Product Focus Super C Tedder Tines AGCO Twine Trouble free spooling Excellent knotting UV Stabilised for tough conditions New! Big Square 1400mt spools to reduce down time AGCO Netwrap Edge to Edge Patented Technology 4200mt Roll Available for reduced down time High strength design Tines are often thought of as a fairly generic product, however the engineers at AGCO have taken the humble tine and designed it for maximum performance and durability. Durability Manufactured using Super C, which is a extremely high quality steel 9.5mm Diameter Rod 6 Windings 70mm Winding Diameter NEW! BIG SQUARE XL 1400MT SPOOLS Get Some Help with the Balancing Act of Baling Hay this Harvest Season with the AGCO HayBoss System The AGCO HayBoss System can measure moisture as you are baling and automatically apply AGCO Hay Preservative to allow baling up to 30% moisture. Information on each bale is recorded into the HayBoss System, which can be downloaded to a file to demonstrate the quality of your hay. Contact your local AGCO Dealer for more information on the AGCO HayBoss System. After the spring coil sections have been wound the surface of the tine coil is Shot Peened. This process closes any micro fissures resulting from the winding process and prevents stress and corrosion failure, prolonging the service life of the tine. To ensure our tedder tines can stand the test of the harshest conditions they must be able to withstand a test cycle of 200, 000 deflections. This is double the industry standard of 100,000. COMB EFFECT FOR OPTIMUM DRYING PROCESS Only equal-sided tines allow you to achieve an optimum mixing of your high-quality forage. This is known as the comb effect since, during the tedding process, the different layers of forage are perfectly mixed together and turned, providing the optimum production of high-quality forage. Another advantage of using tines where both tine legs are of equal length is that the loading on the tine legs from the crop is shared between both tines resulting in consistent load and wear. Furthermore, tines are not handed, ie Left and Right hand tines. On a machine one part number fits all rotors, irrespective of the direction of their rotation. For maximum durability and performance from your machine, always insist on Genuine AGCO Parts. Tine Test Rig 8 September 2017 AGCOPARTSANZ.com.au September 2017 The Genuine Choice 9

Protect your investment by testing moisture content before, during and after the season. The AGCO Parts range of portable moisture testers are now available from your local AGCO Dealer. They operate accurately and quickly, measuring moisture in the field, bin, or shed. Portable Silage / Grain Meter Moisture range: (Silage) 30% - 75% Moisture range: (Grain) 10% - 47% 100 bags included to keep test cell clean Part No. FX01210 Portable Silage Meter Moisture range: 35% - 75% 18 inch stainless steel probe Direct digital readout Part No. FX07980 4 Wheel Drive Filter Kits Superior Technology Portable Hay Meter Moisture range: 8% - 45% Probe length 19.75 Quick to calibrate Part No. FX07920 Get your 4WD ready for summer with heavy-duty 4WD filters from your local AGCO Dealer Knife Stops Part No. Application RRP (Incl GST) S.79699 Knifestop Assembly replacement for Lely $34.01 Mower Blades S.77075 Blade Replacement for Vicon $3.05 S.77074 Blade Replacement for Vicon $3.05 S.77058 Blade Replacement for Kuhn $8.59 S.78415 Blade Replacement for Kuhn/Taarup $3.71 S.78170 Blade Replacement for Claas $3.47 S.78171 Blade Replacement for Claas $3.47 S.59741 Blade Replacement for Taarup $8.78 S.77067 Blade Replacement for Kuhn $2.93 S.77066 Blade Replacement for Kuhn $2.93 S.77117 Blade Replacement for Lely $5.66 S.78404 Blade Replacement for Krone/Fella $3.84 S.78405 Blade Replacement for Krone/Fella $3.84 Rake & Tedder Tines S.9720 Hay Rake Tine replacement for Bamford $3.99 S.77032 Hay Rake Tine Replacement for Sitrex $6.25 S.21313 Hay Rake Tine replacement for Stoll $23.24 S.9721 Hay Rake Tine replacement for New Holland $3.99 S.78180 Hay Rake Tine replacement for Vicon $3.93 S.78121 Hay Tine Tedder replacement for Lely $18.79 S.78120 Hay Tine Tedder replacement for Lely $18.79 S.78113 Hay Rake Tine replacement for Kuhn $25.90 S.77920 Hay Tine Tedder replacement for Claas $25.53 S.78950 Hay Rake Tine replacement for Kuhn $17.78 Baler Blade & Pickup Tines S.104973 Baler Blade replacement for McHale $65.97 S.104961 Baler Blade replacement for Vicon/CaseIH $64.00 S.79740 Baler Pick Up Tine replacement for McHale $11.12 S.79620 Baler Pick Up Tine replacement for Vicon/CaseIH $6.00 Slasher Blades S.72533 Slasher Blade Kit replacement for Howard 78787KN $106.76 S.72534 Slasher Blade Kit replacement for Howard 78663KN $101.96 S.72535 Slasher Blade Kit replacement for Howard 78663KN $99.35 S.118449 Slasher Blade Kit replacement for Jarrett $81.99 These parts are Sparex parts and are not manufactured by the Original Equipment Manufacturer. Original Manufacturers names, part numbers and descriptions are quoted for reference purposes only and are not intended to indicate or suggest that our replacement parts are made by the OEM. Images are for illustrative purposes only and may differ from actual product supplied. To view our huge range of parts and accessories, visit the agcoshop website or contact your local dealer WWW.AGCOSHOP.COM.AU 10 September 2017 AGCOPARTSANZ.com.au September 2017 The Genuine Choice 11

PERFECT BALES TIME AFTER TIME The MF 2200 is built upon a simple, reliable design providing stress-free operation yet produces consistent high bale density time and time again, resulting in reduced quantity of bales for lower handling and transport costs. Consistent high bale density Tandem axle and cutter options Excellent productivity on all four models Highly efficient drive system Reduced power requirement means low running costs CONTACT YOUR LOCAL MASSEY FERGUSON DEALER TODAY CONTACT CT YOUR OUR LOCAL LOCAL MASSEY MASSEY FERGUSON DEALER DEALER TODAY TODAY MASSEYFERGUSON.COM.AU FREECALL 1800 802 914 12 MASSEYFERGUSON.COM.AU FERGUSON, MF, September the triple-triangle logo is a 2017 AGCOPARTSANZ.com.au worldwide FREECALL brand of AGCO. 2017. 1800 1800 802 802 914 914 MASSEY FERGUSON, MF, MF, the MF, the triple-triangle the triple-triangle logo logo is logo a is a worldwide is a worldwide brand brand of AGCO. brand of AGCO. of AGCO. 2017. 2017. 2017. Efficient, with low maintenance and running costs providing low cost of ownership Quality bales that are easy to stack and transport Designed and built by the experts in Hesston, Kansas BUILT IN HESSTON MF 2200 LARGE SQUARE BALER A world of experience. Working with you. h you. A world A world A of world of experience. of experience. Working Working with with you. you. with you.