ECTIN DIRECTRY IZE AND PERFRMANCE UMMARY GLAZING PERFRMANCE GRILLE PRFILE AND PATTERN IZE TABLE DEIGN DATA DETAILED PRDUCT DECRIPTIN CR ECTIN The information published in this document is believed to be accurate at the time of publication. However, because we are constantly working to improve our products, specifications are subject to change without notice. Consult your local Pella representative for up-to-date product information. General Notes: pecifications subject to change without notice. Go to www.pellaadm.com for most current technical data. For complete CI Format pecifications, see www.pellaadm.com. X = Venting or sliding panel as viewed from the exterior. = Fixed panel as viewed from the exterior. Pella 2018 Architectural Design Manual Division 08 penings Windows and Doors www.pellaadm.com F-PD-1
BRAND UMMARY Pella Impervia liding Patio Doors are traditional in every detail with all the Pella innovations you demand. The frame and panel material feature Duracast fiberglass composite, Pella s patented, five layer, engineered fiberglass composite. Duracast fiberglass composite is the strongest, most durable material available in windows and doors. Each door uses three-way reinforced corners for increased strength. All frame and panel corners are locked in place with corner keys and injected with a dual purpose sealant / adhesive for long-lasting performance. Frame corners are additionally secured with mechanical fasteners. Pella Impervia doors are prefinished with a powder-coat paint. This paint meets the stringent AAMA 623 standards. Powder-coat paint is resistant to dents, scratches and damaging UV light. Duracast fiberglass composite can withstand extreme heat (over 200 F), intense cold (-40 F), and is seacoast worthy. BLCK FRAME The versatile block frame design allows units to be installed in masonry openings using installation clips or in wood frame openings using optional fins. Transom and door units can also be field-joined together. Pella 2018 Architectural Design Manual Division 08 penings Windows and Doors www.pellaadm.com F-PD-2
PRDUCT ELECTIN GUIDE ize and Performance Data ound Transmission Class and utdoor-indoor Transmission Class BLCK FRAME IZE tandard izes 6' 8" Door Heights 6' 10" Door Heights 8' Door Heights Available in Fixed-Vent (X), Vent-Fixed (X) and Fixed () pecial izes PERFRMANCE (VENT INGLE UNIT NLY) Meets or Exceeds AAMA / WDMA Ratings 6-0/6-10 D-LC45 Hallmark Certified 6-0/6-10 WITH HIGH PERFRMANCE RETAINER D-LC50 Hallmark Certified 8-0/8-0 D-LC30 Hallmark Certified 8-0/8-0 WITH HIGH PERFRMANCE RETAINER D-LC35 Hallmark Certified Air Infiltration (cfm / ft 2 of frame @ 1.57 psf wind pressure) 1 0.04 0.04 0.04 0.04 Design Pressure 45 psf 50 psf 30 psf 35 psf Water Resistance 6.75 psf 7.5 psf 4.5 psf 5.25 psf THER PERFRMANCE CRITERIA Forced Entry Resistance Level (Minimum ecurity Grade) 2 40/10 40/10 40/10 40/10 Maximum perating Force (lb) Initiate Motion / Maintain Motion 25 / 12 25 / 12 25 / 12 25 / 12 Maximum Locking Force (lb) Lock / Unlock 4 / 5 4 / 5 4 / 5 4 / 5 UND TRANMIIN CLA AND UTDR-INDR TRANMIIN CLA Product Frame ize Tested 3 verall Glazing Thickness Glazing ystem Exterior Glass Thickness Interior Glass Thickness TC Rating ITC Rating 71-1/2" x 79-1/2" 1" 3mm 3mm 27 22 VENT- 71-1/2" x 79-1/2" 1" 3mm 5mm 32 27 71-1/2" x 79-1/2" 1" 4mm 7mm Laminated 32 27 71-1/2" x 79-1/2" 1" 5mm 9mm Laminated 32 29 (1) Published performance data for air infiltration is determined by testing a minimum of four (4) products of NFRC model size. Testing is conducted in accordance with ATM E283. Air infiltration ratings for products will differ by size. The performance data does not apply to combination assemblies unless noted. Actual product performance may vary for a number of reasons including installation and product care. (2) The higher the level, the greater the product s ability to resist forced entry. Grade 40 is achieved with a block frame screw install and grade 10 is achieved with a fin install. (3) ATM E 1425 defines standard sizes for acoustical testing. Ratings achieved at that size are representative of all sizes of the same configuration. Pella 2018 Architectural Design Manual Division 08 penings Windows and Doors www.pellaadm.com F-PD-3
PRDUCT ELECTIN GUIDE Features and ptions GLAZING BLCK FRAME INTERIR HARDWARE FINIH BLCK FRAME Glazing Type Match interior finish Dual-pane Insulating Glass Insulated Glass ptions / Low-E Types Clear Insulating Glass (no Low-E coating) Advanced Low-E Insulating Glass undefense Low-E Insulating Glass AdvancedComfort Low-E Insulating Glass Naturalun Low-E Insulating Glass Additional Glass ptions Tempered Glass bscure Glass1 Gas Fill / High Altitude Argon High Altitude High Altitude with argon EXTERIR / INTERIR Powder-Coat White Powder-Coat Tan, Brown, Black, or Morning ky Gray atin Nickel, Bright Brass, Antique Brass, il-rubbed Bronze, Chrome EXTERIR HARDWARE FINIH Match exterior finish LCKING YTEM Multi-Point Locking ystem electroplated steel Multi-Point Locking ystem tainless teel Keylock Foot Bolt GRILLE Grilles-Between-the-Glass 3/4" contoured White, Tan, Brown, Black, or Morning ky Gray (match interior and exterior finish) Patterns Traditional Prairie Top Row pecial Dual-color (All exterior colors available with White interior) CREEN Conventional black fiberglass interior sliding screen door InView fiberglass interior sliding screen door = tandard; = ptional (1) Contact your local Pella sales representative for current offering. Pella 2018 Architectural Design Manual Division 08 penings Windows and Doors www.pellaadm.com F-PD-4
GLAZING PERFRMANCE - TTAL UNIT Glass Thickness Type of Glazing NFRC Certified Product # Glass (mm) Ext. Int. Gap Fill U-Factor Performance Values 1 HGC VLT CR haded Areas Meet ENERGY TAR Performance Criteria in Zones hown U.. Canada 2 Zone ER Zone N NC C 1 2 3 1" Clear IG PEL-N-123-00639-00001 3 3 air 0.48 0.61 0.63 44 with grilles-between-the-glass PEL-N-123-00639-00002 0.48 0.53 0.55 44 1" Clear IG PEL-N-123-00641-00001 4 4 air 0.48 0.59 0.63 44 with grilles-between-the-glass PEL-N-123-00641-00002 0.48 0.52 0.55 44 1" Clear IG PEL-N-123-00644-00001 5 5 air 0.48 0.58 0.62 44 with grilles-between-the-glass PEL-N-123-00644-00002 0.48 0.51 0.54 44 1" Advanced Low-E IG PEL-N-123-00670-00001 3 3 argon 0.32 0.29 0.54 54 with grilles-between-the-glass PEL-N-123-00670-00002 0.32 0.26 0.47 54 1" Advanced Low-E IG PEL-N-123-00672-00001 4 4 argon 0.32 0.28 0.53 54 with grilles-between-the-glass PEL-N-123-00672-00002 0.32 0.25 0.47 54 1" Advanced Low-E IG PEL-N-123-00675-00001 5 5 argon 0.32 0.28 0.53 54 with grilles-between-the-glass PEL-N-123-00675-00002 0.32 0.25 0.46 54 1" undefense IG PEL-N-123-00684-00001 3 3 argon 0.32 0.22 0.50 54 with grilles-between-the-glass PEL-N-123-00684-00002 0.32 0.19 0.44 54 1" undefense IG PEL-N-123-00686-00001 4 4 argon 0.32 0.22 0.49 54 with grilles-between-the-glass PEL-N-123-00686-00002 0.32 0.19 0.43 54 1" undefense IG PEL-N-123-00689-00001 5 5 argon 0.31 0.21 0.49 54 with grilles-between-the-glass PEL-N-123-00689-00002 0.31 0.19 0.43 54 1" AdvancedComfort Low-E IG PEL-N-123-00696-00001 3 3 argon 0.27 0.28 0.53 46 22 with grilles-between-the-glass PEL-N-123-00696-00002 0.27 0.25 0.46 46 20 1" AdvancedComfort Low-E IG PEL-N-123-00698-00001 4 4 argon 0.27 0.28 0.52 46 22 with grilles-between-the-glass PEL-N-123-00698-00002 0.27 0.25 0.46 46 20 1" AdvancedComfort Low-E IG PEL-N-123-00700-00001 5 5 argon 0.27 0.28 0.52 45 22 with grilles-between-the-glass PEL-N-123-00700-00002 0.27 0.25 0.45 45 20 1" Naturalun Low-E IG PEL-N-123-00658-00001 3 3 argon 0.33 0.54 0.61 54 30 with grilles-between-the-glass PEL-N-123-00658-00002 0.33 0.47 0.53 54 26 1" Naturalun Low-E IG PEL-N-123-00660-00001 4 4 argon 0.33 0.52 0.61 53 29 with grilles-between-the-glass PEL-N-123-00660-00002 0.33 0.46 0.53 53 25 1" Naturalun Low-E IG PEL-N-123-00662-00001 5 5 argon 0.33 0.51 0.60 53 28 with grilles-between-the-glass PEL-N-123-00662-00002 0.33 0.45 0.52 53 25 WITH FAM INULATIN 1" Advanced Low-E IG PEL-N-123-00744-00001 3 3 argon 0.29 0.29 0.54 58 with grilles-between-the-glass PEL-N-123-00744-00002 0.29 0.26 0.47 58 1" Advanced Low-E IG PEL-N-123-00746-00001 4 4 argon 0.29 0.28 0.53 57 with grilles-between-the-glass PEL-N-123-00746-00002 0.29 0.25 0.47 57 1" Advanced Low-E IG PEL-N-123-00749-00001 5 5 argon 0.29 0.28 0.53 57 with grilles-between-the-glass PEL-N-123-00749-00002 0.29 0.25 0.46 57 1" undefense IG PEL-N-123-00758-00001 3 3 argon 0.29 0.22 0.50 58 with grilles-between-the-glass PEL-N-123-00758-00002 0.29 0.19 0.44 58 1" undefense IG PEL-N-123-00760-00001 4 4 argon 0.29 0.22 0.49 58 with grilles-between-the-glass PEL-N-123-00760-00002 0.29 0.19 0.43 58 1" undefense IG PEL-N-123-00763-00001 5 5 argon 0.29 0.21 0.49 57 with grilles-between-the-glass PEL-N-123-00763-00002 0.29 0.19 0.43 57 1" AdvancedComfort Low-E IG PEL-N-123-00770-00001 3 3 argon 0.25 0.28 0.53 47 25 with grilles-between-the-glass PEL-N-123-00770-00002 0.25 0.25 0.46 47 23 1" AdvancedComfort Low-E IG PEL-N-123-00772-00001 4 4 argon 0.25 0.28 0.52 46 25 with grilles-between-the-glass PEL-N-123-00772-00002 0.25 0.25 0.46 46 23 1" AdvancedComfort Low-E IG PEL-N-123-00774-00001 5 5 argon 0.25 0.28 0.52 46 25 with grilles-between-the-glass PEL-N-123-00774-00002 0.25 0.25 0.45 46 23 1" Naturalun Low-E IG PEL-N-123-00732-00001 3 3 argon 0.30 0.54 0.61 57 33 with grilles-between-the-glass PEL-N-123-00732-00002 0.30 0.47 0.53 57 29 1" Naturalun Low-E IG PEL-N-123-00734-00001 4 4 argon 0.30 0.52 0.61 57 32 with grilles-between-the-glass PEL-N-123-00734-00002 0.30 0.46 0.53 57 29 1" Naturalun Low-E IG PEL-N-123-00736-00001 5 5 argon 0.30 0.51 0.60 57 32 with grilles-between-the-glass PEL-N-123-00736-00002 0.30 0.45 0.52 57 28 R-Value = 1/U-Factor HGC = olar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating Rev. 03/15/2018 (1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY TAR values are updated to 2016 (Version 6) criteria. (2) The values shown are based on Canada's updated ENERGY TAR 2015 initiative. For center-glass values, see the Product Performance section. ee the Product Performance section for more detailed information or visit www.energystar.gov for Energy tar guidelines. Pella 2018 Architectural Design Manual Division 08 penings Windows and Doors www.pellaadm.com F-PD-5
GLAZING PERFRMANCE - TTAL UNIT High Altitude Glazing Glass Thickness Type of Glazing NFRC Certified Product # Glass (mm) Ext. Int. Gap Fill U-Factor Performance Values 1 HGC VLT CR haded Areas Meet ENERGY TAR Performance Criteria in Zones hown U.. Canada 2 Zone ER Zone HIGH ALTITUDE GLAZING N NC C 1 2 3 1" (HA) Advanced Low-E IG PEL-N-123-00663-00001 3 3 air 0.36 0.29 0.54 54 with grilles-between-the-glass PEL-N-123-00663-00002 0.36 0.26 0.47 54 1" (HA) Advanced Low-E IG PEL-N-123-00665-00001 4 4 air 0.36 0.29 0.53 53 with grilles-between-the-glass PEL-N-123-00665-00002 0.36 0.25 0.47 53 1" (HA) Advanced Low-E IG PEL-N-123-00668-00001 5 5 air 0.35 0.29 0.53 53 with grilles-between-the-glass PEL-N-123-00668-00002 0.35 0.25 0.46 53 1" (HA) undefense IG PEL-N-123-00677-00001 3 3 air 0.35 0.22 0.50 54 with grilles-between-the-glass PEL-N-123-00677-00002 0.35 0.19 0.44 54 1" (HA) undefense IG PEL-N-123-00679-00001 4 4 air 0.35 0.22 0.49 53 with grilles-between-the-glass PEL-N-123-00679-00002 0.35 0.19 0.43 53 1" (HA) undefense IG PEL-N-123-00682-00001 5 5 air 0.35 0.22 0.49 53 with grilles-between-the-glass PEL-N-123-00682-00002 0.35 0.19 0.43 53 1" (HA) AdvancedComfort Low-E IG PEL-N-123-00691-00001 3 3 air 0.30 0.28 0.53 43 with grilles-between-the-glass PEL-N-123-00691-00002 0.30 0.25 0.46 43 1" (HA) AdvancedComfort Low-E IG PEL-N-123-00693-00001 4 4 air 0.30 0.28 0.52 43 with grilles-between-the-glass PEL-N-123-00693-00002 0.30 0.25 0.46 43 1" (HA) AdvancedComfort Low-E IG PEL-N-123-00695-00001 5 5 air 0.30 0.28 0.52 42 with grilles-between-the-glass PEL-N-123-00695-00002 0.30 0.25 0.45 42 1" (HA) Naturalun Low-E IG PEL-N-123-00653-00001 3 3 air 0.36 0.53 0.61 54 25 with grilles-between-the-glass PEL-N-123-00653-00002 0.36 0.47 0.53 54 1" (HA) Naturalun Low-E IG PEL-N-123-00655-00001 4 4 air 0.36 0.52 0.61 53 25 with grilles-between-the-glass PEL-N-123-00655-00002 0.36 0.46 0.53 53 1" (HA) Naturalun Low-E IG PEL-N-123-00657-00001 5 5 air 0.36 0.51 0.60 53 with grilles-between-the-glass PEL-N-123-00657-00002 0.36 0.45 0.52 53 HIGH ALTITUDE GLAZING WITH FAM INULATIN 1" (HA) Advanced Low-E IG PEL-N-123-00737-00001 3 3 air 0.33 0.29 0.54 55 with grilles-between-the-glass PEL-N-123-00737-00002 0.33 0.26 0.47 55 1" (HA) Advanced Low-E IG PEL-N-123-00739-00001 4 4 air 0.33 0.29 0.53 54 with grilles-between-the-glass PEL-N-123-00739-00002 0.33 0.25 0.47 54 1" (HA) Advanced Low-E IG PEL-N-123-00742-00001 5 5 air 0.32 0.29 0.53 54 with grilles-between-the-glass PEL-N-123-00742-00002 0.32 0.25 0.46 54 1" (HA) undefense IG PEL-N-123-00751-00001 3 3 air 0.33 0.22 0.50 55 with grilles-between-the-glass PEL-N-123-00751-00002 0.33 0.19 0.44 55 1" (HA) undefense IG PEL-N-123-00753-00001 4 4 air 0.32 0.22 0.49 55 with grilles-between-the-glass PEL-N-123-00753-00002 0.32 0.19 0.43 55 1" (HA) undefense IG PEL-N-123-00756-00001 5 5 air 0.32 0.22 0.49 54 with grilles-between-the-glass PEL-N-123-00756-00002 0.32 0.19 0.43 54 1" (HA) AdvancedComfort Low-E IG PEL-N-123-00765-00001 3 3 air 0.27 0.28 0.53 44 22 with grilles-between-the-glass PEL-N-123-00765-00002 0.27 0.25 0.46 44 20 1" (HA) AdvancedComfort Low-E IG PEL-N-123-00767-00001 4 4 air 0.27 0.28 0.52 43 22 with grilles-between-the-glass PEL-N-123-00767-00002 0.27 0.25 0.46 43 20 1" (HA) AdvancedComfort Low-E IG PEL-N-123-00769-00001 5 5 air 0.27 0.28 0.52 43 22 with grilles-between-the-glass PEL-N-123-00769-00002 0.27 0.25 0.45 43 20 1" (HA) Naturalun Low-E IG PEL-N-123-00727-00001 3 3 air 0.34 0.53 0.61 55 28 with grilles-between-the-glass PEL-N-123-00727-00002 0.34 0.47 0.53 55 1" (HA) Naturalun Low-E IG PEL-N-123-00729-00001 4 4 air 0.33 0.52 0.61 54 29 with grilles-between-the-glass PEL-N-123-00729-00002 0.33 0.46 0.53 54 25 1" (HA) Naturalun Low-E IG PEL-N-123-00731-00001 5 5 air 0.33 0.51 0.60 54 28 with grilles-between-the-glass PEL-N-123-00731-00002 0.33 0.45 0.52 54 25 R-Value = 1/U-Factor HGC = olar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating Climate Zones (1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY TAR values are updated to 2016 (Version 6) criteria. (2) The values shown are based on Canada's updated ENERGY TAR 2015 initiative. For center-glass values, see the Product Performance section. ee the Product Performance section for more detailed information or visit www.energystar.gov for Energy tar guidelines. Rev. 03/15/2018 Pella 2018 Architectural Design Manual Division 08 penings Windows and Doors www.pellaadm.com F-PD-6
PRDUCT PERFRMANCE Combination Assembles Combinations are a great way to create visual interest in any project. A combination is an assembly formed by two or more separate windows or doors whose frames are mulled together by a combination or reinforcing mullion. Pella door combinations are available in an endless variety of arrangements. Below are some field-assembled combinations. ome units can be fixed or vent depending on availability. ee the combinations section, for typical combinations and requirements and limitations related to mulling various units. Contact your local Pella sales representative for more information. TRANM VER X ARCH HEAD VER X HALF CIRCLE VER X ARCH HEAD VER HALF CIRCLE VER / X Click here for the Impervia Combinations ection Downloadable PDF file. Pella 2018 Architectural Design Manual Division 08 penings Windows and Doors www.pellaadm.com F-PD-7
GRILLE TYPE Grilles-Between-the-Glass Grille Profiles GRILLE-BETWEEN-THE-GLA 3/4" 3/4" Contoured Grille Patterns PRAIRIE PATTERN tandard corner lite dimension for Prairie patterns = 4" visible glass (VG). Pattern availability may vary depending on size of unit. 9-Lite Prairie 6-Lite Prairie ADDITINAL PATTERN Pattern availability may vary depending on size of unit. Traditional Top Row 1 pecial (1) tandard visible glass to center line of separator bar = 14" or half of total visible glass height, whichever is smaller. Multiple rows are available up to 50% glass size. Pella 2018 Architectural Design Manual Division 08 penings Windows and Doors www.pellaadm.com F-PD-8
IZE TABLE Transoms, Fixed and Vent Units Transoms (1 113) (1 100) pening 3' 8 7 / 8 " Frame 3' 7 3 / 8" (1 524) (1 511) 5' 0" (1 829) (1 816) 6' 0" 4' 11 1/ 2" 5' 11 1/ 2" (457) (356) (445) (343) (610) (597) 2' 0" 1' 6" 1' 2" 1' 11 1 / 2" 1' 5 1/ 2" 1' 1 1/ 2 " 3-8/1-2 3-8/1-6 3-8/2-0 5-0/1-2 5-0/1-6 5-0/2-0 6-0/1-2 6-0/1-6 6-0/2-0 pening Frame (810) (797) (962) (949) (1 113) (1 100) (1 267) (1 254) (1 524) (1 829) (2 134) (2 438) (1 511) (1 816) (2 121) (2 426) 2' 7 7 / 8 " 3' 17 / 8 " 3' 8 7 / 8 " 4' 17 / 8 " 5' 0" 6' 0" 7' 0" 8' 0" 2' 7 3 / 8" 3' 13 / 8" 3' 7 3 / 8" 4' 13 / 8" 4' 11 1 / 2" 5' 11 1 / 2" 6' 11 1/ 2" 7' 11 1/ 2" (2 032) (2 019) (2 083) (2 070) 6' 8" 6' 10" 1 / 2" 6' 9 1 / 2 " 6' 7 1/ 2 " 2-8/6-8 2-8/6-10 3-2/6-8 3-2/6-10 3-8/6-8 3-8/6-10 4-2/6-8 4-2/6-10 VENT- (X) * 5-0/6-8 VENT- (X) * 6-0/6-8 VENT- (X) * 7-0/6-8 VENT- (X) * 8-0/6-8 VENT- (X) * VENT- (X) * VENT- (X) * VENT- (X) * 5-0/6-10 6-0/6-10 7-0/6-10 8-0/6-10 (2 438) (2 426) 8' 0" 7' 11 3-2/8-0 3-8/8-0 4-2/8-0 VENT- (X) * VENT- (X) * VENT- (X) * 6-0/8-0 7-0/8-0 8-0/8-0 Not to scale. pecial sizes available to the nearest 1/4". All dimensions are approximate to the nearest 1/16" * Two panel doors Vent-Fixed (X), left panel opens, right panel is fixed. Units open in the direction of the arrows as viewed from the exterior. Fixed-Vent (X) doors are also available. Pella 2018 Architectural Design Manual Division 08 penings Windows and Doors www.pellaadm.com F-PD-9
DEIGN DATA LIDING PATI DR DEIGN DATA Unit 6'8" DR Venting Clear pening Width (Inches) Height (Inches) Vent Area Ft2 Visible Glass Ft2 tandard Glass Thickness (mm) Annealed Tempered Performance Class & Grade 1,2 2-8/6-8 12.1 3 LC50 3-2/6-8 15.1 4 LC50 3-8/6-8 18.1 4 LC50 4-2/6-8 21.1 4 LC50 5-0/6-8 X, X 22-5/16 74-7/8 11.4 24.9 3 LC45/LC50 6-0/6-8 X, X 28-5/16 74-7/8 14.5 30.9 3 LC45/LC50 7-0/6-8 X, X 33-5/16 74-7/8 17.6 37.0 4 LC30/LC35 8-0/6-8 X, X 40-5/16 74-7/8 20.8 43.0 5 LC30/LC35 6'10" DR 2-8/6-10 12.4 3 LC50 3-2/6-10 15.5 4 LC50 3-8/6-10 18.6 4 LC50 4-2/6-10 21.7 4 LC50 5-0/6-10 X, X 22-5/16 76-7/8 11.7 25.6 3 LC45/LC50 6-0/6-10 X, X 28-5/16 76-7/8 14.9 31.8 3 LC45/LC50 7-0/6-10 X, X 33-5/16 76-7/8 18.1 38.0 4 LC30/LC35 8-0/6-10 X, X 40-5/16 76-7/8 21.3 44.2 5 LC30/LC35 8' DR 3-2/8-0 18.4 4 LC50 3-8/8-0 22.1 4 LC50 4-2/8-0 25.8 4 LC50 6-0/8-0 X, X 28-5/16 90-7/8 17.6 37.8 5 LC30/LC35 7-0/8-0 X, X 33-5/16 90-7/8 21.4 45.2 4 LC30/LC35 8-0/8-0 X, X 40-5/16 90-7/8 25.2 52.5 5 LC30/LC35 TRANM 3-8/1-2 1.9 3 3 LC50 5-0/1-2 2.8 3 3 LC50 6-0/1-2 3.4 3 3 LC50 3-8/1-6 3.0 2.5 3 LC50 5-0/1-6 4.2 2.5 3 LC50 6-0/1-6 5.2 3 3 LC50 3-8/2-0 4.5 2.5 3 LC50 5-0/2-0 6.5 2.5 3 LC50 6-0/2-0 7.9 2.5 3 LC50 ( ) = Not Applicable (1) Maximum performance when glazed with the appropriate glass thickness. (2) econd number indicates performance rating with High Performance Retainer. Pella 2018 Architectural Design Manual Division 08 penings Windows and Doors www.pellaadm.com F-PD-10
MICELLANEU FRMULA Miscellaneous Glass Formulas FRAME PANEL ACTUAL GLA VIIBLE GLA CLEAR PENING DR Frame Width = Rough opening width 1/2" Frame Height = Rough opening height 1/2" Width of X/X = (Frame width / 2) 13/16" Width of = Frame Width 2-3/8" Panel Height = Frame height 2-3/16" Width of X/X = (Frame width / 2) 4-15/16" Width of = Frame Width 6-1/2" Glass Height = Frame height 6-5/16" Width of X/X = (Frame width / 2) 5-7/8" Width of = Frame Width 7-3/8" VG Height = Frame height 7-3/16" Clear pening Width = (Frame width / 2) 7-7/16" Clear pening Height = Frame height 4-9/16" TRANM Frame Width = Rough opening width 1/2" Frame Height = Rough opening height 1/2" ash Width = Frame width 2-13/16" ash Height = Frame height 2-13/16" Glass Width = Frame width 5-1/8" Glass Height = Frame height 5-1/8" VG Width = Frame width 6-1/16" VG Height = Frame height 6-1/16" Not Applicable pecial ize Frame Dimensions FRAME WIDTH FRAME HEIGHT MINIMUM MAXIMUM MINIMUM (MAXIMUM) VENT DR (X, X) 47-1/2" 95-1/2" 71-1/2" 95-1/2" PANEL () 27" 49" 71-1/2" 95-1/2" TRANM 47-1/2" 71-1/2" 13-1/2" 23-1/2" Frame dimensions are on the nearest 1/4" increment. Doors that are less than or equal to 54-3/4" in width do not meet 20" egress requirements. Pella 2018 Architectural Design Manual Division 08 penings Windows and Doors www.pellaadm.com F-PD-11
DETAILED PRDUCT DECRIPTIN FRAME Frame is Duracast fiberglass composite five-layer pultruded fiberglass material [with optional foam insulation 1] reinforced with a Pella patented interlocking mat. verall frame depth is 4-3/4". Nominal wall thickness of Duracast members are.070" to.120" thick. Duracast sill powder-coat painted brown with an oak threshold. Frame corners are mitered, joined and bonded with nylon corner lock and mechanically fastened. Jamb to head corners sealed with injected polyurethane adhesive. Jambs and head contain factory-drilled (counter-bored) installation screw holes when ordered without nail fin. DR PANEL Panel is Duracast fiberglass composite five-layer pultruded fiberglass material [with optional foam insulation 1] reinforced with a Pella patented interlocking mat. All panel members have mitered corners joined and bonded with corner locks, injected with polyurethane adhesive. Vent panels have two adjustable permanently-sealed electroplated steel with organic coating ball-bearing rollers, set on stainless steel track. EXTERIR / INTERIR Duracast surfaces are factory applied with powder-coat paint finish. Color is [White] [Tan] [Brown] [Black] [Morning ky Gray]. - or - Dual-color option [Tan] [Brown] [Black] [Morning ky Gray] exterior with White interior. GLAZING YTEM Quality float glass complying with ATM C 1036. 1" insulating glass tempered [obscure 2] [[clear] [Advanced] [undefense ] [AdvancedComfort] [Naturalun] Low-E coated, with argon]] sealed and bonded to panel. High altitude glazing is available. WEATHERTRIPPING Flexible polymeric bulb section with welded corners and a slip-coating at head, jamb, sill and interlocker. Bristle strip rain-screen at vent panel interlocker. HARDWARE Interior handle, thumb lock for inside locking is [powder-coat [White] [Tan] [Brown] [Matte Black] [Morning ky Gray] to match finish] [atin Nickel] [Bright Brass] [Antique Brass] [il-rubbed Bronze] [Chrome]. Exterior handle is powder-coat painted to match exterior. Non elf-locking Foot Bolt. Finish on Black, Brown and Morning ky Gray interior units is Brown. Finish on Tan interior units is Tan, and Finish on White interior units is White. Foot bolt holds the door open approximately 3" for ventilation. PTINAL PRDUCT creens Conventional Black Fiberglass Black vinyl coated 18/16 mesh fiberglass screen cloth complying with ATM D 3656 and MA 1201. et in aluminum frame and fitted to the inside of door. upplied complete with all necessary hardware. creen finish is baked enamel, color to match sliding door interior. - or - InView screen Vinyl-coated 18/18 mesh fiberglass screen cloth complying with MA 1201, set in aluminum frame fitted to inside of door, supplied complete with all necessary hardware. et in aluminum frame and fitted to the inside of door. upplied complete with all necessary hardware. creen finish is baked enamel, color to match sliding door interior. Grilles Grilles-Between-the-Glass Insulating glass contains 3/4" contoured aluminum grilles permanently installed between two panes of glass. Grilles are factory prefinished [White] [Tan] [Brown] [Black] [Morning ky Gray] to match interior and exterior finish. Hardware Keylock with K-keyway cylinder. Finish is [Chrome]. FAM INULATIN INERT 1 liding Patio Door XH VENT HEAD FJ JAMB I INTERLCKER X VENT ILL LJ LCK JAMB (1) Foam insulation inserts are not available with clear glazing. (2) bscure glazing is not available when AdvancedComfort Low-E coated IG is specified. Rev. 01/03/2018 Pella 2018 Architectural Design Manual Division 08 penings Windows and Doors www.pellaadm.com F-PD-12
UNIT ECTIN VENT X 4 3/4" [121] XH H 1 3/16" [30] 1 3/16" [30] LJ I FJ 3 3/4" [95] 3 3/4" [95] XH VENT HEAD H HEAD X FRAME HEIGHT 1 1/4" [32] FRAME HEIGHT 1 1/4" [32] X VENT ILL ILL 2 1/16" [52] 3 9/16" [91] 1 3/16" [30] 1 1/4" [32] 1" [25] 3 9/16" [91] 7/8" [22] LJ LCK JAMB I INTERLCKER FJ JAMB 1 5/16" [33] 3 7/8" [98] 2 9/16" [65] 4 5/16" [110] FRAME WIDTH 2 9/16" [65] 3 3/4" [95] 1 3/16" [30] cale 3" = 1' 0" All dimensions are approximate. Pella 2018 Architectural Design Manual Division 08 penings Windows and Doors www.pellaadm.com F-PD-13
UNIT ECTIN 3" TRANM [76] TH TJ 3 1/16" [77] 1 13/16" [45] TJ TRANM JAMB 1 13/16" [45] T FRAME HEIGHT 15/16" [24] TH T TRANM HEAD TRANM ILL 3" [76] 15/16" [24] 1 5/8" [41] 3 1/16" [77] 1 5/8" [41] 1 7/16" [36] 1 7/16" [36] FRAME WIDTH IDE LIGHT 4 3/4" [121] H 1 3/16" [30] J 3 3/4" [95] H IDELIGHT HEAD J IDELIGHT JAMB 1 3/16" [30] FRAME HEIGHT 1 1/4" [32] 4 3/4" [121] 1 1/4" [32] IDELIGHT ILL 2 9/16" [65] 1" [25] 7/8" [22] 3 3/4" [95] FRAME WIDTH 2 9/16" [65] 1 3/16" [30] FRAME FRAME ILL HEAD 6 13/16" [173] JINING MULLIN WITH TAPE (Horizontal nly) cale 3" = 1' 0" All dimensions are approximate. Pella 2018 Architectural Design Manual Division 08 penings Windows and Doors www.pellaadm.com F-PD-14