Vulcan Parallel pring Diaphragm Type eals 48 ection
INTRODUTION Vulcan s Parallel pring Diaphragm Type eals are highly proficient and widely utilised, covering all standard pump shaft, working length and housing size ranges. PPLITION The parallel spring family range of designs are ideal for a wide spectrum of application conditions, ranging from general duties through to more demanding applications, through their accommodating ingle prings and elastomer Diaphragms. The seals are highly effective and widely utilised in pumps, mixers, agitators, compressors and other rotary shaft equipment. TNDRD VULN PRLLEL TYPE Types 10, 20 and 20 Parallel spring, rubber diaphragm seals to common industry standard dimensions. Fitted as standard with Type 20 boot mounted seats, Type 20 has a Type 21 O -Ring mounted stationary. Types 11, 11J and 22 s above, to common merican standard dimensions, fitted with a Type 11 boot mounted seats, or Type 11J has a Type 31 O -Ring mounted seat. Types U11/N11 s above Type 11, but to full NI compatibility, through incorporating a narrow profile seal design. Type U11 utilises the same seal head internal design as our Type 24, whilst Type N11 incorporates an elastomer resiliently mounted ring face. Type 24 eries s above but to full DIN24960 (EN1276) dimensions, K-length. Type 24 is supplied with a Type 24 boot mounted seat as standard. You should specify Type 24, if a Type 24.DIN stationary is required and Type 24L for the Type 24.DINL stationary. TNDRD OMPONENT VULN DEIGN DVNTGE ccommodating The seal head automatically adjusts to accommodate misalignment and seal face wear, through the design and flexibility of the rubber diaphragm. Improved Designs Vulcan s attention to detail and modern in-house design and manufacturing facilities, have enabled Vulcan to create Parallel pring eals, with additional improvements to the original designs, whilst still maintaining the main design features, such as self aligning, non-fretting / clogging and vacuum application suitability. These improvements result in a superior Vulcan Mechanical eal, to both the original replacement seal and their other direct market copies. Retained omponents Faces and base plates are retained by adhesive grease and by mating components, respectively, making handling and fitting easier and more secure. ustomisable The technically efficient and highly versatile, parallel spring, seal design can be readily customised to suit individual requirements; where a standard seal or seat cannot be utilised. Vulcan can assist in the design of special production runs to fully satisfy customer requirements. Quality wide selection of high quality face materials and elastomers are readily available as standard. Reliability The resulting Vulcan Quality eal and the high strength and flexibility of the diaphragm, provide a very reliable and accommodating mechanical seal design. OUR PRLLEL PRING DIPRGM TYPE EL PV RT 30 43 2 363 Pressure (bar g) 20 1 10 290 217 14 Pressure (psig) NO DERIPTION 1 EL FE 2 RETINER 3 DIPRGM 4 DRIVE RING PRING 6 BE PLTE 0 0 2mm (1.0 ) 38mm (1. ) 0mm (2.0 ) 63mm (2. ) haft ize 7mm (3.0 ) 89mm (3. ) 73 0 100mm (4.0 ) RT BED UPON: RBON V RETION BONDED ILION RBIDE EL FE 10/20/11/22/24 1/2/4/ 49
TYPE 10 / 20 (METRI) lso available with O -Ring mounted seats, as Types 10 and 20, please refer overleaf. In addition, Types 10/20 are often purchased as a seal only to be installed with any one of a variety of seats. VULN TNDRD IZE haft ize DØ 10 12 13 14 1 16 18 19 20 22 24 2 28 29 30 32 33 34 3 38 40 41 42 43 44 4 48 0 3 8 60 63 6 70 7 80 8 90 9 100 ize ode 0100 0120 0130 0140 010 0160 0180 0191 0200 0220 0240 020 0280 0290 0300 0320 0330 0340 0349 0381 0400 0410 0420 0430 0440 040 0480 000 030 00 080 0600 0630 060 0700 070 0800 080 0900 090 1000 shaft size, resilient, single spring, rubber diaphragm seal with a Type 20 boot mounted stationary as standard, to suit originally common UK housing sizes. widely utilised seal type, highly suited to general duties, capable of long service life. 24.60 27.79 27.79 30.9 30.9 30.9 34.1 34.1 3.70 37.30 40.0 40.0 47.63 47.63 0.80 0.80 3.98 3.98 3.98 7.1 60.3 63.0 63.0 63.0 63.0 66.68 69.8 76.20 82. 92.08 9.2 101.60 114.30 117.48 123.83 1 133.3 21.80 23.0 23.0 30.70 30.70 39.20 39.20 4.60 4.60 47.40 47.40 2.00 2.00 2.00.60 9.20 9.20 6.10 6.10 6.10 6.10 66.70 71.00 73.30 78.60 82.10 82.10 84.60 88.60 102.70 108.00 112.00 119.00 124.00 TYPE 10 69.8 69.8 73.03 82. 8.73 TYPE 20 49.21 49.21 2.39.6.6.6 8.74 61.91 8.74 8.74 8.74 13.0 13.0 13.0 13.0 13.0 13.0 1.88 1.88 1.88 ll types, sizes and materials shown are part of Vulcan s Guaranteed Ex-tock Range, unless marked with an asterisk*. owever, the asterisked seal and / or seat face materials are stocked in many, but not all, sizes. uggested Operating Limits GURNTEED TOK MTERIL ND FE MTERIL ODE eal nd eat ssembly Face Reference Term OFT Rotary Face ode ode M106K arbon ode 99% eramic OFT V RD D M106K arbon VE2 RB i RD V OFT G VE2 RB i 99% eramic RD VE2 RB i VE2 RB i RD 1st LT Tungsten arbide* Tungsten arbide* Guaranteed tock Elastomers: Viton, E.P. and Nitrile 0 tationary Face Guaranteed tock Metallurgy: 304 Please refer to the Technical and tandards ection for advice and information on Face s, haft ize, peed and Media. Please refer to the eal Type pecific PV hart, found at the front of this Brochure ection, in combination with the Vulcan Multiplying Factors found in Technical and tandards ection 2.
TYPE 10 / 20 (IMPERIL) shaft size, resilient, single spring, rubber diaphragm seal with Type 20 boot mounted stationary as standard, to suit common originally UK housing sizes. widely utilised seal type, highly suited to general duties, capable of long service life. lso available with O -Ring mounted seats, as Types 10 and 20. Please refer overleaf. In addition, Types 10/20 are often purchased as a seal only to be installed with any one of a variety of seats. VULN TNDRD IZE haft ize TYPE 10 TYPE 20 ize DØ ode 0.37 009 24.60 21.80 8.74 0.00 0127 27.79 23.0 8.74 0.62 018 30.9 0.70 0191 34.1 30.70 0.87 0222 37.30 1.000 024 40.0 43.20 1.12 0286 47.63 46.60 1.20 0317 0.80 47.40 1.37 0349 3.98 2.00 1.00 0381 7.1.60 1.62 0412 9.20 1.70 0444 63.0 6.10 1.87 0476 66.68 66.70 2.000 008 69.8 73.30 13.0 2.12 039 73.03 73.30 13.0 2.20 071 76.20 78.60 13.0 2.37 0603 82.10 13.0 2.00 063 82. 84.60 13.0 2.62 0666 92.08 88.60 69.8 49.21 1.88 2.70 0698 9.2 92.00 69.8 49.21 1.88 2.87 0730 98.43 9.20 73.03 2.39 1.88 3.000 0762 101.60 102.70 73.03 2.39 1.88 3.12 0794 111.1.6 3.20 082 114.30.6 3.37 087 117.48 108.00.6 3.00 0889 120.6 112.00.6 3.62* 0921 123.83 114.00 82. 8.74 3.70 093 1 119.00 82. 8.74 3.87* 0984 130.20 121.00 8.73 61.91 4.000 1016 133.3 124.00 8.73 61.91 ll types, sizes and materials shown are part of Vulcan s Guaranteed Ex-tock Range, unless marked with an asterisk*. owever, most asterisked sizes are stocked in some, but not all, materials. nd the asterisked materials in many sizes. uggested Operating Limits Face s, haft ize, peed and Media. Please refer to the eal Type pecific PV hart, found at the front of this Brochure ection, in combination with the Vulcan Multiplying Factors found in Technical and tandards ection 2. GURNTEED TOK MTERIL ND FE MTERIL ODE eal nd eat ssembly Rotary Face tationary Face Face Reference Term ode ode ode OFT M106K arbon 99% eramic OFT V RD D M106K arbon VE2 RB i RD V OFT G VE2 RB i 99% eramic RD VE2 RB i VE2 RB i RD 1st LT Tungsten arbide* Tungsten arbide* Guaranteed tock Elastomers: Viton, E.P. and Nitrile Guaranteed tock Metallurgy: 304 Please refer to the Technical and tandards ection for advice and information on 1
TYPE 20 ingle spring, resilient, rubber diaphragm seal featuring a Type 20 rotary with an O -Ring mounted Type 21 stationary seat option, to suit common UK housing sizes. very widely specified and utilised seal type, highly suited to diverse duties, and capable of long service life. hould you require a Type 10 seal assembly, please order a Type 10 seal and a Type 21 stationary as separate components. VULN TNDRD IZE haft ize DØ ize ode 0.37 009 24.60 21.80 8.74 0.00 0127 27.79 23.0 8.74 0.62 018 30.9 0.70 0191 34.1 30.70 0.87 0222 37.30 1.000 024 40.0 43.20 1.12 0286 47.63 4.60 1.20 0317 0.80 47.40 1.37 0349 3.98 2.00 1.00 0381 7.1.60 1.62 0412 9.20 1.70 0444 63.0 6.10 1.87 0476 66.68 66.70 2.000 008 69.8 73.30 13.0 2.12 039 73.03 73.30 13.0 2.20 071 76.20 78.60 13.0 2.37 0603 82.10 13.0 2.00 063 82. 84.60 13.0 2.62 0666 92.08 88.60 49.21 1.88 2.70 0698 9.2 49.21 1.88 2.87 0730 98.43 9.20 2.39 1.88 3.000 0762 101.60 102.70 2.39 1.88 3.12* 0794 111.1.6 3.20* 082 114.30.6 3.37* 087 117.48 108.00.6 3.00* 0889 120.6 112.00.6 3.62* 0921 123.83 114.00 8.74 3.70* 093 1 119.00 8.74 3.87* 0984 130.20 121.00 61.91 4.000* 1016 133.3 124.00 61.91 ll types, sizes and materials shown are part of Vulcan s Guaranteed Ex-tock Range, unless marked with an asterisk*. owever, most asterisked sizes are stocked in some, but not all, materials. nd the asterisked materials in many sizes. GURNTEED TOK MTERIL ND FE MTERIL ODE Rotary Face eal nd eat ssembly Face Reference Term 2 ode tationary Face ode ode OFT M106K arbon 99% eramic OFT V METL Q M106K arbon 304 tainless teel Q OFT V METL F M106K arbon Ni-Resist* F OFT V RD D M106K arbon VE2 RB i RD E M106K arbon Tungsten arbide* RD VE2 RB i VE2 RB i RD 1st LT Tungsten arbide* Tungsten arbide* Guaranteed tock Elastomers: Viton, E.P. and Nitrile Guaranteed tock Metallurgy: 304 Please refer to the Technical and tandards ection for advice and information on uggested Operating Limits Face s, haft ize, peed and Media. Please refer to the eal Type pecific PV hart, found at the front of this Brochure ection, in combination with the Vulcan Multiplying Factors found in Technical and tandards ection 2.
TYPE 11 / 22 VULN TNDRD IZE haft ize DØ haft ize DØ ize ode uggested Operating Limits Face s, haft ize, peed and Media. Please refer to the eal Type pecific PV hart, found at the front of this Brochure ection, in combination with the Vulcan Multiplying Factors found in Technical and tandards ection 2. ingle spring, resilient, rubber diaphragm seal with two working length options, and a Type 11 boot mounted stationary as standard, to suit common originally merican housing sizes. widely utilised seal type, highly suited to general duties, capable of long service life. lso available with O -Ring mounted seats, as Types 11J and 22J, Please refer over-leaf. In addition, Types 11/22 can be purchased as a seal only to be installed with any one of a variety of seats. TYPE 11 TYPE 22 0.00 0127 1.000 0.92 23.0 0.812 20.62 1.20 31.7 0.312 7.93 14 0140 1.20 31.7 1.063 0.87 22.23 1.37 34.93 0.40 10.28 0.62 018 1.20 31.7 1.063 0.87 22.23 1.37 34.93 0.40 10.28 16 0160 1.20 31.7 1.063 0.87 22.23 1.37 34.93 0.40 10.28 18 0180 1.37 34.93 1.209 30.70 0.87 22.23 1.37 34.93 0.40 10.28 0.70 0191 1.37 34.93 1.209 30.70 0.87 22.23 1.37 34.93 0.40 10.28 20 0200 1.00 38.10 1.31 0.937 23.80 1.437 36.0 0.40 10.28 22 0220 1.00 38.10 1.31 0.937 23.80 1.437 36.0 0.40 10.28 0.87 0222 1.00 38.10 1.31 0.937 23.80 1.437 36.0 0.40 10.28 24 0240 1.62 41.28 1.43 39.20 1.000 1.62 41.28 0.437 11.10 2 020 1.62 41.28 1.43 39.20 1.000 1.62 41.28 0.437 11.10 1.000 024 1.62 41.28 1.701 43.20 1.000 1.62 41.28 0.437 11.10 28 0280 1.70 44.44 1.79 4.60 1.062 26.97 1.687 42.8 0.437 11.10 1.12 0286 1.70 44.44 1.79 4.60 1.062 26.97 1.687 42.8 0.437 11.10 30 0300 1.87 47.63 1.866 47.40 1.062 26.97 1.687 42.8 0.437 11.10 1.20 0317 1.87 47.63 1.866 47.40 1.062 26.97 1.687 42.8 0.437 11.10 32 0320 1.87 47.63 1.866 47.40 1.062 26.97 1.687 42.8 0.437 11.10 33 0330 2.000 0.80 2.047 2.00 1.12 28.8 1.687 42.8 0.437 11.10 1.37 0349 2.000 0.80 2.047 2.00 1.12 28.8 1.687 42.8 0.437 11.10 3 030 2.000 0.80 2.071 2.00 1.12 28.8 1.687 42.8 0.437 11.10 38 0380 2.12 3.98 2.189.60 1.12 28.8 1.687 42.8 0.437 11.10 1.00 0381 2.12 3.98 2.197.60 1.12 28.8 1.687 42.8 0.437 11.10 40 0400 2.37 2.331 9.20 1.37 34.93 2.000 0.80 0.00 12.70 1.62 0412 2.37 2.331 9.20 1.37 34.93 2.000 0.80 0.00 12.70 43 0430 2.00 63.0 2.63 6.10 1.37 34.93 2.000 0.80 0.00 12.70 1.70 0444 2.00 63.0 2.63 6.10 1.37 34.93 2.000 0.80 0.00 12.70 4 040 2.62 66.68 2.63 6.10 1.00 38.10 2.12 3.98 0.00 12.70 1.87 0476 2.62 66.68 2.626 66.70 1.00 38.10 2.12 3.98 0.00 12.70 48 0480 2.70 69.8 2.626 66.70 1.00 38.10 2.12 3.98 0.00 12.70 0 000 2.70 69.8 2.79 71.00 1.00 38.10 2.12 3.98 0.00 12.70 2.000 008 2.70 69.8 2.886 73.30 1.00 38.10 2.12 3.98 0.00 12.70 3 030 3.000 76.20 2.886 73.30 1.687 42.8 2.37 60.32 0.62 14.28 2.12 039 3.000 76.20 2.886 73.30 1.687 42.8 2.37 60.32 0.62 14.28 00 3.12 3.094 78.60 1.687 42.8 2.37 60.32 0.62 14.28 2.20 071 3.12 3.094 78.60 1.687 42.8 2.37 60.32 0.62 14.28 60 0600 3.20 82. 3.232 82.10 1.812 46.02 2.00 63.0 0.62 14.28 2.37 0603 3.20 82. 3.232 82.10 1.812 46.02 2.00 63.0 0.62 14.28 2.00 063 3.37 8.73 3.331 84.60 1.812 46.02 2.00 63.0 0.62 14.28 6 060 3.37 8.73 3.488 88.60 1.937 49.20 2.70 69.8 0.62 1.88 2.62 0666 3.37 8.73 3.488 88.60 1.937 49.20 2.70 69.8 0.62 1.88 2.70 0698 3.00 88.90 3.43 1.937 49.20 2.70 69.8 0.62 1.88 70 0700 3.00 88.90 3.43 1.937 49.20 2.70 69.8 0.62 1.88 2.87 0730 3.70 9.2 3.748 9.20 2.062 2.37 2.87 73.03 0.62 1.88 7 070 3.87 98.43 4.043 102.70 2.062 2.37 2.87 73.03 0.62 1.88 3.000 0762 3.87 98.43 4.043 102.70 2.062 2.37 2.87 73.03 0.62 1.88 3.12 0794 4.000 101.60 4.094 2.187. 3.12 79.37 3.20 082 4.12 104.78 4.094 2.187. 3.12 79.37 3.37 087 4.20 107.9 4.22 108.00 2.187. 3.12 79.37 3.00 0889 4.37 111.13 4.409 112.00 2.187. 3.12 79.37 3.62* 0921 4.00 114.30 4.488 114.00 2.312 8.72 3.20 82. 3.70 093 4.62 117.48 4.68 119.00 2.312 8.72 3.20 82. 3.87* 0984 4.70 120.6 4.764 121.00 2.312 8.72 3.37 8.72 4.000 1016 4.87 123.83 4.882 124.00 2.312 8.72 3.37 8.72 ll types, sizes and materials shown are part of Vulcan s Guaranteed Ex-tock Range, unless marked with an asterisk*. owever, most asterisked sizes are stocked in some, but not all, materials. nd the asterisked materials in many sizes. GURNTEED TOK MTERIL ND FE MTERIL ODE eal nd eat ssembly Rotary Face tationary Face Face Reference Term ode ode ode OFT M106K arbon 99% eramic OFT V RD D M106K arbon VE2 RB i RD V OFT G VE2 RB i 99% eramic RD VE2 RB i VE2 RB i RD 1st LT Tungsten arbide* Tungsten arbide* Guaranteed tock Elastomers: Viton, E.P. and Nitrile Guaranteed tock Metallurgy: 304 Please refer to the Technical and tandards ection for advice and information on 3
TYPE 11J ingle spring, resilient, rubber diaphragm seal featuring Type 11 rotary with an O Ring mounted Type 31 stationary option, to suit common originally merican housing sizes. very widely specified and utilised seal type, highly suited to most duties, and capable of long service life. hould you require a Type 22J eal assembly, please order a Type 22 eal and a Type 31 stationary, as separate seal and seat components. VULN TNDRD IZE ize haft ode ize DØ 0.00 0.62 0.70 0.87 1.000 1.12 1.20 1.37 1.00 1.62 1.70 1.87 2.000 2.12 2.20 2.37 2.00 2.62 2.70 3.000 3.12* 3.20* 3.37* 3.00* 3.62* 3.70* 3.87* 4.000* 0127 018 0191 0222 024 0286 0317 0349 0381 0412 0444 0476 008 039 071 0603 063 0666 0698 0762 0794 082 087 0889 0921 093 0984 1016 1.000 1.20 1.37 1.00 1.62 1.70 1.87 2.000 2.12 2.37 2.00 2.62 2.70 3.000 3.12 3.20 3.37 3.37 3.00 3.87 4.000 4.12 4.20 4.37 4.00 4.62 4.70 4.87 31.7 34.93 38.10 41.28 44.44 47.63 0.80 3.98 63.0 66.68 69.8 76.20 82. 8.73 8.73 88.90 98.43 101.60 104.78 107.9 111.13 114.30 117.48 120.6 123.83 0.898 1.063 1.197 1.31 1.47 1.60 1.787 1.941 2.067 2.18 2.402 2.20 2.87 2.776 3.10 3.134 3.209 3.437 3.43 3.811 4.094 4.094 4.22 4.409 4.488 4.68 4.764 4.882 22.80 30.40 39.30 41.90 4.40 49.30 2.0.0 61.00 64.00 6.70 70.0 80.00 79.60 81.0 87.30 96.80 108.00 112.00 114.00 119.00 121.00 124.00 0.812 0.87 0.87 0.937 1.000 1.062 1.062 1.12 1.12 1.37 1.37 1.00 1.00 1.687 1.687 1.812 1.812 1.937 1.937 2.062 2.187 2.187 2.187 2.187 2.312 2.312 2.312 2.312 20.62 22.23 22.23 23.80 26.97 26.97 28.8 28.8 34.93 34.93 38.10 38.10 42.8 42.8 46.02 46.02 49.20 49.20 2.37.... 8.72 8.72 8.72 8.72 0.312 0.40 0.40 0.40 0.437 0.437 0.437 0.437 0.437 0.00 0.00 0.00 0.00 0.62 0.62 0.62 0.62 0.62 0.62 0.62 7.93 10.28 10.28 10.28 11.10 11.10 11.10 11.10 11.10 12.70 12.70 12.70 12.70 14.28 14.28 14.28 14.28 1.88 1.88 1.88 ll types, sizes and materials shown are part of Vulcan s Guaranteed Ex-tock Range, unless marked with an asterisk*. owever, most asterisked sizes are stocked in some, but not all, materials. nd the asterisked materials in many sizes. GURNTEED TOK MTERIL ND FE MTERIL ODE eal nd eat ssembly Face Reference Term 4 Rotary Face ode tationary Face ode ode OFT M106K arbon 99% eramic* OFT V METL Q M106K arbon 304 tainless teel* Q OFT V METL F M106K arbon Ni-Resist F OFT V RD D M106K arbon VE2 RB i RD E M106K arbon Tungsten arbide* RD VE2 RB i VE2 RB i RD 1st LT Tungsten arbide* Tungsten arbide* Guaranteed tock Elastomers: Viton, E.P. and Nitrile Guaranteed tock Metallurgy: 304 Please refer to the Technical and tandards ection for advice and information on uggested Operating Limits Face s, haft ize, peed and Media. Please refer to the eal Type pecific PV hart, found at the front of this Brochure ection, in combination with the Vulcan Multiplying Factors found in Technical and tandards ection 2.
TYPE N11 (U11) ingle spring, rubber diaphragm seal, similar to Type 11, but with reduced O.D. () to give full NI seal chamber compatibility. lso available as Types N11J or U11J with an O -Ring mounted seat. Type N11; with resilient elastomer mounted face, is the preferred design supplied up to its design limit of 2.000 / 0 mm. Type U11 has a retainer lug driven face, as per our Type 24 design and is the preferred design, that is supplied in all sizes above 2.000 / 0 mm. VULN TNDRD IZE ize haft ode ize DØ 0.00 0127 1.000 0.898 22.80 0.812 20.62 0.312 7.93 0.62 018 1.20 31.7 1.063 0.87 22.23 0.40 10.28 0.70 0191 1.37 34.93 1.197 30.40 0.87 22.23 0.40 10.28 0.87 0222 1.00 38.10 1.31 0.937 23.80 0.40 10.28 1.000 024 1.62 41.28 1.47 39.30 1.000 0.437 11.10 1.12 0286 1.70 44.44 1.60 41.90 1.062 26.97 0.437 11.10 1.20 0317 1.87 47.63 1.787 4.40 1.062 26.97 0.437 11.10 1.37 0349 2.000 0.80 1.941 49.30 1.12 28.8 0.437 11.10 1.00 0381 2.12 3.98 2.067 2.0 1.12 28.8 0.437 11.10 1.62 0412 2.37 2.18.0 1.37 34.93 0.00 12.70 1.70 0444 2.00 63.0 2.402 61.00 1.37 34.93 0.00 12.70 1.87 0476 2.62 66.68 2.20 64.00 1.00 38.10 0.00 12.70 2.000 008 2.70 69.8 2.87 6.70 1.00 38.10 0.00 12.70 2.12 039 3.000 76.20 2.776 70.0 1.687 42.8 0.62 14.28 2.20 071 3.12 3.10 80.00 1.687 42.8 0.62 14.28 2.37 0603 3.20 82. 3.134 79.60 1.812 46.02 0.62 14.28 2.00 063 3.37 8.73 3.209 81.0 1.812 46.02 0.62 14.28 2.62 0666 3.37 8.73 3.437 87.30 1.937 49.20 0.62 1.88 2.70 0698 3.00 88.90 3.43 1.937 49.20 0.62 1.88 3.000 0762 3.87 98.43 3.811 96.80 2.062 2.37 0.62 1.88 3.12 0794 4.000 101.60 4.094 2.187. 3.20 082 4.12 104.78 4.094 2.187. 3.37 087 4.20 107.9 4.22 108.00 2.187. 3.00 0889 4.37 111.13 4.409 112.00 2.187. 3.62* 0921 4.00 114.30 4.488 114.00 2.312 8.72 3.70 093 4.62 117.48 4.68 119.00 2.312 8.72 3.87* 0984 4.70 120.6 4.764 121.00 2.312 8.72 4.000 1016 4.87 123.83 4.882 124.00 2.312 8.72 ll types, sizes and materials shown are part of Vulcan s Guaranteed Ex-tock Range, unless marked with an asterisk*. owever, most asterisked sizes are stocked in some, but not all, materials. nd the asterisked materials in many sizes. uggested Operating Limits Face s, haft ize, peed and Media. Please refer to the eal Type pecific PV hart, found at the front of this Brochure ection, in combination with the Vulcan Multiplying Factors found in Technical and tandards ection 2. GURNTEED TOK MTERIL ND FE MTERIL ODE eal nd eat ssembly Rotary Face tationary Face Face Reference Term ode ode ode OFT M106K arbon 99% eramic OFT V RD D M106K arbon VE2 RB i RD VE2 RB i VE2 RB i RD 1st LT Tungsten arbide* Tungsten arbide* Guaranteed tock Elastomers: Viton, E.P. and Nitrile Guaranteed tock Metallurgy: 304 Please refer to the Technical and tandards ection for advice and information on
TYPE 24 ompact, single spring, rubber diaphragm seal specifically designed to comply with DIN 24960 (EN 1276) K-length dimensional requirements, for the complete seal and seat assembly. vailable as standard with Type 24 bootmounted stationary. For O -Ring mounted versions, please see opposite page. In addition, Type 24 is often purchased as a seal only to be installed with any one of a variety of seats. K VULN TNDRD IZE haft ize DØ ize ode K 12 0120 23.00 21.70 23.90 8.60 32.0 14 0140 2.00 24.40 26.40 8.60 3.00 16 0160 26.40 8.60 3.00 18 0180 33.00 30.60 27.0 37.0 20 0200 3.00 27.0 37.0 22 0220 37.00 27.0 37.0 24 0240 39.00 37.80 30.00 40.00 2 020 40.00 39.20 30.00 40.00 28 0280 43.00 42.10 32.0 42.0 30 0300 4.00 44.00 32.0 42.0 32 0320 48.00 4.60 32.0 42.0 33 0330 48.00 4.60 32.0 42.0 3 030 0.00 49.30 32.0 42.0 38 0380 6.00 2.70 34.00 11.00 4.00 40 0400 8.00.70 34.00 11.00 4.00 43 0430 61.00 8.60 34.00 11.00 4.00 4 040 63.00 61.00 34.00 11.00 4.00 48 0480 66.00 64.00 34.00 11.00 4.00 0 000 70.00 66.10 34.0 47.0 3 030 73.00 70.60 34.0 47.0 00 7.00 70.60 34.0 47.0 8 080 78.00 80.00 39.0 2.0 60 0600 80.00 80.00 39.0 2.0 63 0630 83.00 82.10 39.0 2.0 6 060 8.00 8.00 39.0 2.0 68 0680 37.20 1.30 2.0 70 0700 92.00 44.70 1.30 60.00 7 070 97.00 96.80 44.70 1.30 60.00 80 0800 44.30 1.70 60.00 8 080 1 108.00 44.30 1.70 60.00 90 0900 11.00 111.00 49.30 1.70 6.00 9 090 120.00 119.00 49.30 1.70 6.00 100 1000 12.00 124.00 49.30 1.70 6.00 ll types, sizes and materials shown are part of Vulcan s Guaranteed Ex-tock Range, unless marked with an asterisk*. owever, the asterisked seal and / or seat face materials are stocked in many, but not all, sizes. uggested Operating Limits GURNTEED TOK MTERIL ND FE MTERIL ODE eal nd eat ssembly Face Reference Term OFT Rotary Face ode M106K arbon ode 99% eramic OFT V RD D M106K arbon VE2 RB i RD V OFT G VE2 RB i 99% eramic RD VE2 RB i VE2 RB i RD 1st LT Tungsten arbide* Tungsten arbide* Guaranteed tock Elastomers: Viton, E.P. and Nitrile 6 tationary Face ode Guaranteed tock Metallurgy: 304 Please refer to the Technical and tandards ection for advice and information on Face s, haft ize, peed and Media. Please refer to the eal Type pecific PV hart, found at the front of this Brochure ection, in combination with the Vulcan Multiplying Factors found in Technical and tandards ection 2.
TYPE 24L / 24 Photo illustrates Type 24L VULN TNDRD IZE ize haft ize K ode DØ uggested Operating Limits Face s, haft ize, peed and Media. Please refer to the eal Type pecific PV hart, found at the front of this Brochure ection, in combination with the Vulcan Multiplying Factors found in Technical and tandards ection 2. K ompact, single spring, rubber diaphragm seal specifically designed to comply with DIN 24960 (EN 1276) K-length dimensional requirements, for the complete seal and seat assembly. The Type 24 seal s highly proficient and accommodating design enables it to be widely utilised. vailable as Type 24L with an O -Ring mounted stationary with anti-rotation provision, or as Type 24 with a short O -Ring mounted stationary. LOT WIDT 24L LOT DEPT 24L 12 0120 23.00 21.70 23.90 8.60 32.0 4.00.00 14 0140 2.00 24.40 26.40 8.60 3.00 4.00.00 16 0160 26.40 8.60 3.00 4.00.00 18 0180 33.00 30.60 27.0 37.0 4.00.0 20 0200 3.00 27.0 37.0 4.00.0 22 0220 37.00 27.0 37.0 4.00.0 24 0240 39.00 37.80 30.00 40.00 4.00.0 2 020 40.00 39.20 30.00 40.00 4.00.0 28 0280 43.00 42.10 32.0 42.0 4.00.0 30 0300 4.00 44.00 32.0 42.0 4.00.0 32 0320 48.00 4.60 32.0 42.0 4.00.0 33 0330 48.00 4.60 32.0 42.0 4.00.0 3 030 0.00 49.30 32.0 42.0 4.00.0 38 0380 6.00 2.70 34.00 11.00 4.00.00.0 40 0400 8.00.70 34.00 11.00 4.00.00.0 43 0430 61.00 8.60 34.00 11.00 4.00.00.0 4 040 63.00 61.00 34.00 11.00 4.00.00.0 48 0480 66.00 64.00 34.00 11.00 4.00.00.0 0 000 70.00 66.10 34.0 47.0.00.0 3 030 73.00 70.60 34.0 47.0.00.0 00 7.00 70.60 34.0 47.0.00.0 8 080 78.00 80.00 39.0 2.0.00.0 60 0600 80.00 80.00 39.0 2.0.00.0 63 0630 83.00 82.10 39.0 2.0.00.0 6 060 8.00 8.00 39.0 2.0.00.0 68 0680 37.20 1.30 2.0.00.0 70 0700 92.00 44.70 1.30 60.00.00.0 7 070 97.00 96.80 44.70 1.30 60.00.00.0 80 0800 44.30 1.70 60.00.00.0 8 080 1 108.00 44.30 1.70 60.00.00.0 90 0900 11.00 111.00 49.30 1.70 6.00.00.0 9 090 120.00 119.00 49.30 1.70 6.00.00.0 100 1000 12.00 124.00 49.30 1.70 6.00.00.0 ll types, sizes and materials shown are part of Vulcan s Guaranteed Ex-tock Range, unless marked with an asterisk*. owever, the asterisked seal and / or seat face materials are stocked in many, but not all, sizes. GURNTEED TOK MTERIL ND FE MTERIL ODE eal nd eat ssembly Rotary Face tationary Face Face Reference Term ode ode ode OFT M106K arbon 99% eramic OFT V RD D M106K arbon VE2 RB i RD V OFT G VE2 RB i 99% eramic RD VE2 RB i VE2 RB i RD 1st LT Tungsten arbide* Tungsten arbide* Guaranteed tock Elastomers: Viton, E.P. and Nitrile Guaranteed tock Metallurgy: 304 Please refer to the Technical and tandards ection for advice and information on 7