HH 102 DRILLING RIG
HH102 Hydraulic with Caterpillar engine, for drilling oil and gas wells up to 2,000 m 100 tf hook capacity 1000 HP triplex pumps Mongoose shakers Design and basic rig designed in accordance with API Specifications, designed for fast moving operation. The rig and its accessories are designed o to operate in climate temperatures from minus 20 C o to plus 40 C. Drill pipe stands handling Range 3 (single) Max pull 220,000 lbs (100 metric ton) Mast clear height from ground level 87.9 ft (26.8 m) Top drive torque 26,035 lbs-ft (3530 danm) Top drive stroke 52 ½ ft (16 m) Max pull down 44,000 lbs (20 metric ton) Max power 600 hp (447.5 kw) Weight in transport condition 99,200 lbs (45 metric ton) Trailer a semitrailer heavy duty type for off-road operation with: - welded frame made of high-grade steel - braking system consisting of a double circuit air operated by brakes - pneumatic operated front and rear suspension for perfect leveling - walkway and handrails - stairs from ground to semitrailer Power pack Diesel engine C18 - ACERT with hoisting power of 600 hp at 1800 RPM continuos rate, water cooled Crown block fixed to mast telescopic section complete with 4 sheaves of crown block (diameter 25 ½" - grooves 34 mm) and wire line sheave (diameter 25" - grooves 5/8") Rotary table DRILLMEC design, driven by 2 hydraulic motors Substructure made of high-grade steel complete with: - rails and trolley to facilitate the sliding of BOP to the well centerline - one stairway from drill floor to trailer - the rotary table is flush with the working floor - one ramp for casing - one set of handrails - control cabin frame Top drive driven by 4 top-head hydraulic motors assembled on a special dolly sliding on mast guide, equipped with hydraulic brake - I.D. full opening 3" - variable speed 0 to 154 rpm - torque range 0 to 26,000 lbft - max torque 26,000 lbft (35826 Nm) to 66 RPM - stroke 52'6" - casing clearance 52'6" - max pull up 220,000 lbs - max pull down 44,000 lbs - max working pressure 5000 psi
MR 8000 DRILLING RIG
MR 8000 Diesel powered, with Caterpillar engines and Allison converters, for drilling oil and gas wells up to 3,200 m 200 tf hook capacity Triplex pumps Brandt/ Cobra shakers Main drum D 26" x L 42" line 1 1/8 Brake rims: D46' x W8" removable forged steel Input power: 800 HP Spooling capacity: 700 m (2300 ft) of 1 1/8" wireline Max single line pull: 24,000 kg with Lebus grooves Cooling circulating water Airflex 42 VC650 Clutch Oilfield carrier/ 4 axles trailer Heavy duty off road type Carrier 12 x 8 configuration High resistance, I beams Electrically welded frame Hydraulic leveling jacks for quick leveling of the rig on ground Mechanical and hydraulic safety blocks on jacks Sand line drum Max single line pull: 13,000 kg with Lebus jacket Spooling capacity: 4800 m (2300 ft) of 6/16"wireline Brake rims: d38"x W7" removeable forged steel. Cooling: circulating water Mast Static hook capacity: 200 tons (440.000 lbs) Mast dear height: 36 m (118') Monkey board for double drill pipes (18 m) Crown block 5 sheaves OD 30" for 1 1/8" Power pack Diesel engine: 2 Caterpillar C 15 ACERT Carrier version Transmission: Allison S5610 with torque converter TC 682 Rotary table clutch Fawick 20CB 500 Trailer version Torque Converter TC 955 Rotary table Drillmec R 27.5 (27" ½ opening and 300 ton dead loading) Drawwork options Hydromatic Parmac V80 brake with water circulation system Lebus grooving on either drum Substructure Parallelogram folding type, height 5.2 m (17 tf) Hydraulic system and controls Hydraulic mast erection Hydraulic jacks for mast telescoping Hydraulic top drive Hydraulic cathead Operator console: tubing drum; engine and transmission controls. Substructure transport configuration Two pieces with following dimension: Frame Set Back Rotary table Width 2.5 m (8 ) 2.5 m (8 ) Height 2.04 m (6 8") 2.26 m (7 5") Length 12.5 m (41 ) 12.5 m (41 ) Anchoring system: self anchoring system through guy lines and rig pad (only two anchoring in the ground are required).
A lifetime drilling company F 100 DRILLING RIG
F100 Electrical and Diesel powered, with CAT 3512 LAND RIG generators, for drilling oil and gas wells up to 2,300 m. 100 tf hook capacity Triplex pumps JF 1000 that provide working pressures up to 350 bars and a capacity and a capacity of 43 l/sec. Mongoose shakers Systems for measuring and monitoring the drilling parameters type DIAFOR 2000 and DATAFOR. Recommended drilling depth 2300 m Hook max load 100 tf Working system: number of wires 8 Speeds to the hook 2 Power to the drilling hoist 415 HP Maximum tension 15 tf Diameter of the working cable 25 mm Maximum power for the table bushing 500 HP Number of speeds to the rotary table 2+2 revers Maximum diameter MRS 205 520 mm (20 1/2") Maximum length for the mast steps 27 m Power pump groups 2 Maximum power for mud pump 1000 HP Mast MA 100 - static hook capacity 125 tf - free height 40.8 m Substructure - rotary max load 100 tf - pipe max load 70 tf - height 3.75 m Crown block GF 100T - static hook load 100 tf - rolls 5 - working cable 25 mm Hook crane 100T - maximum hook load 100tf - rolls 4 - working cable 25 mm Chain hoist TF15 - entrance power 415 HP Rotary table MRS 205 - static load 320 tf - max power 500 HP - rotation speed 300 rpm - transmission rate 3.68:1 Hydraulic head CH 125 T - max static load 125 tf - max rotation speed 300 rpm - max pressure 300 bars Mud pumps JF 1000 - power 1000 HP - 41 l/sec - 305 mm (12") Shakers ALLS II/ 80-250 mesh Drilling parameters registration DATAFOR
F125 DRILLING RIG
F125 Electrical and Diesel powered, with CAT 3512 LAND RIG generators, for drilling oil and gas wells up to 2,800 m. 125 tf hook capacity Triplex pumps JF 1000 that provide working pressures up to 350 bars and a capacity of 43 l/sec. Mongoose shakers Systems for measuring and monitoring the drilling parameters type DIAFOR 2000 and DATAFOR. Recommended drilling depth 2800 m Hook max load 125 tf Working system: number of wires 8 Speeds to the hook 4 Power to the drilling hoist 1250 HP Maximum tension 20 tf Diameter of the working cable 28 mm Maximum power for the table bushing 500 HP Maximum diameter MRL 205 520 mm (20 1/2") Maximum length for the mast steps 27 m Power pump groups 2 Maximum power for mud pump 1000 HP Mast MA 125 - static hook capacity 125 tf - free height 40.09 m Substructure - rotary max load 100 tf - pipe max load 80 tf - height 5 m Crown block GF 125T - static hook load 200 tf - rolls 5 - working cable 28 mm Hook crane 125T - maximum hook load 200 tf - rolls 4 - working cable 28 mm Chain hoist TF20 - entrance power 1250 HP Rotary table MRL 205 - static load 320 tf - max power 500 HP - rotation speed 300 rpm - transmission rate 3.68:1 Hydraulic head CH 320 T - max static load 320 tf - max rotation speed 300 rpm - max pressure 300 bars Mud pumps JF 1000 - power 1000 HP - 41 l/sec - 305 mm (12") Shakers Mongoose / 40-250 mesh Drilling parameters registration DIAFOR 2000
F 200 DRILLING RIG
F200 Electrical, it can be easily adapted for Diesel powered with CAT 3512 LAND RIG generators, for drilling oil and gas wells between 2,500 m and 4,000 m 200 tf hook capacity Triplex pumps JF 1000 that provide working pressures up to 350 bars and a capacity of 43 l/sec. Mongoose shakers Systems for measuring and monitoring the drilling parameters type DIAFOR 2000 and DATAFOR. Recommended drilling depth 4000 m Hook max load 200 tf Working system: number of wires 10 Speeds to the hook 2 Power to the drilling hoist 1600 HP Maximum tension 25 tf Diameter of the working cable 32 mm Maximum power for the table bushing 500 HP Number of speeds to the rotary table 2+2 revers Maximum diameter MRS 175 698.5 mm (27 ½") Maximum length for the mast steps 27 m Power pump groups 2 Maximum power for mud pump 1000 HP Mast MA 100 - static hook capacity 50 tf - free height 41.8 m Substructure - rotary max load 200 tf - pipe max load 125 tf - height 5 m Crown block GF 75T - static hook load 300 tf - rolls 6 - working cable 352 mm Hook crane 75T - maximum hook load 300tf - rolls 5 - working cable 32 mm Chain hoist TF10 - entrance power 1600 HP Rotary table MRS 175 - static load 500 tf - max power 600 HP - rotation speed 300 rpm - transmission rate 3.68:1 Hydraulic head - max static load 320 tf - max rotation speed 300 rpm - max pressure 300 bars Mud pumps JF 1000 - power 1000 HP - 41 l/sec - 305 mm (12") Shakers Mongoose/ 40-250 mesh Drilling parameters registration DIAFOR 2000
F 320 DRILLING RIG
F320 Electrical, it can be easily adapted for Diesel powered with CAT 3512 LAND RIG generators, for drilling oil and gas wells between 4,000 m and 6,000 m 320 tf hook capacity Triplex pumps CF 1000 that provide working pressures up to 350 bars and a capacity of 46.5 l/sec Mongoose shakers Systems for measuring and monitoring the drilling parameters type SMART and weight indicators type Martin Decker. Recommended drilling depth 4000-6000 m (4 ½ pipes) Hook max load 320 tf Working system number of wires 10 Speeds to the hook 4 Power to the drilling hoist 2300 HP Maximum tension 38 tf Diameter of the working cable 35 mm Maximum power for the table bushing 600 HP Number of speeds to the rotary table 2 Maximum diameter MRL 275 698.5 mm (27 ½ ) Maximum length for the mast steps 27 m Power pump groups 2 Maximum power for mud pump 1300 HP Mast MA 320 - static hook capacity 320 tf - free height 44 m Substructure - rotary max load 320 tf - pipe max load 200 tf - height 5.5 m Crown block GF 75T - static hook load 400 tf - rolls 6 - working cable 35 mm Hook crane 75T - maximum hook load 400 tf - rolls 5 - working cable 35 mm Chain hoist TF 10 - entrance power 2300 HP Rotary table MRS 175 - static load 500 tf - max power 600 HP - rotation speed 300 rpm - transmission rate 3.68:1 Hydraulic head CH 400T - max load 400 tf - max rotation speed 300 rpm - max pressure 300 bars Mud pumps CF 1300 - power 1300 HP - 45.4 l/sec - 305 mm (12") Shakers Brandt Cobra/ 40-250 mesh Drilling parameters registration SMART
A lifetime drilling company F 400 DRILLING RIG
F400 Electrical, it can be easily adapted for Diesel powered with CAT 3512 LAND RIG generators, for drilling oil and gas wells between 5,000 m and 7,000 m 400 tf hook capacity Triplex pumps CF 1300 that provide working pressures up to 350 bars and a capacity of 46.5 l/sec. Mongoose and Brandt/Cobra shakers Systems for measuring and monitoring the drilling parameters type SMART and weight indicators type Martin Decker. Recommended drilling depth 5000-7000 m (with 4 ½ pipes) Hook max load 400 tf Working system: number of wires 12 Speeds to the hook 4 Power to the drilling hoist 2300 HP Maximum tension 44 tf Diameter of the working table 35 mm Maximum power for the table bushing 600 HP Number of speeds to the rotary table 2+2 revers Maximum diameter MRL 275 698.5 mm (27 ½") Maximum length for the mast steps 27 m Power pump groups 2 Maximum power for mud pump 1300 HP Mast MA 400 - static hook capacity 400 tf - free height 44 m Substructure - rotary max load 400 tf - pipe max load 260 tf - height 5.3 m Crown block GF 500T - static hook load 500 tf - rolls 7 - working cable 35 mm Hook crane 500T - maximum hook load 500 tf - rolls 6 - working cable 35 mm Chain hoist TF44 - entrance power 2300 HP Rotary table MRS 275 - static load 500 tf - max power 600 HP - rotation speed 300 rpm - transmission rate 3.68:1 Hydraulic head CH 400T - max static load 400 tf - max rotation speed 300 rpm - max pressure 300 bars Mud pumps CF 1300 - power 1300 HP - 45.4 l/sec - 305 mm (12") Shakers Mongoose/ 40-250 mesh Drilling parameters registration SMART
A lifetime drilling company T 50 DRILLING RIG
T50 Electrical and Diesel powered with CAT 3512 LAND RIG generators, for drilling oil and gas wells up to 1,200 m 50 tf hook capacity Triplex pumps JF 1000 that provide working pressures up to 350 bars and a capacity of 43 l/sec. Mongoose shakers Recommended drilling depth - with 4 ½ drilling pipes 1200 m - with 3 ½ drilling pipes 1700 m Working system: number of wires 6 Speeds to the hook 2 Power to the drilling hoist 300 HP Maximum tension 10 tf Diameter of the working table 25 mm Maximum power for the table bushing 500 HP Number of speeds to the rotary table 2+2 revers Maximum diameter MRS 175 444.5 mm (17 ½") Maximum length for the mast steps 18 m Power pump groups 2 Maximum power for mud pump 700 HP Mast T50 - telescopic and reversible - static hook capacity 50 tf Substructure - rotary max load 50 tf - pipe max load 50 tf - height 2.65 m Crown block GF 75T - static hook load 75 tf - rolls 4 - working cable 25 mm Hook crane 75T - maximum hook load 75 tf - rolls 3 - working cable 25 mm Chain hoist TF10 - entrance power 300 HP Rotary table MRS 175 - static load 50 tf - max power 300 HP - rotation speed 200 rpm - transmission rate 3.68:1 Hydraulic head - max static load 125 tf - max rotation speed 300 rpm - max pressure 210 bars Mud pumps - power 700 HP - 44.4 l/sec - 254 mm (10") Shakers ALS II/ 80-250 mesh Drilling parameters registration DATAFOR