Part # 13040199 05-14 Mopar LX Level 1 Air Suspension System Front Components: 1 1304409 Front RQ ShockWave Kit for Stock Lower Arms Rear Components: 1 13044099 Rear CoolRide Kit 1 13040709 RQ Series Rear Shocks Compressor System: 1 30154000 3 gallon Analog RidePro Compressor Kit
Part # 1304409 Mopar LX Platform Front Shockwave RQ Series 05-08 Magnum / 05-Up 300C / 06-Up Charger / 08-Up Challenger Shockwave: 4090198 1000 Master Series double convoluted bellow assembly 4459999 5 stroke shock w/ threaded bottom RQ Series 9000357 Aluminum Reducer Puck 90009986 Stud top (Stud top base not needed) 90001668 (SKW076) Aluminum lower shock mount 90009980 (A953) Lower Shockwave steel bracket 70008913 Locking Ring Components: 4 90009 Steel washer for rubber mount (.375 O.D.) 90001974 Upper rubber isolator 90001973 Lower rubber isolator (T-shaped) 90001971 Aluminum upper ShockWave plate 9000448 Wide Lower Shockwave steel bracket 3195401 ¼ x ¼ swivel elbows Hardware: 9956003 9/16-18 Nylok jam nut Stud top to upper mount 99561008 9/16-18 x 3 1/4 bolt NARROW Lower bracket to lower arm 99561009 9/16-18 x 4 bolt WIDE Lower bracket to lower arm 9956001 9/16-18 Nylok nut Lower bracket to lower arm 6 99371006 3/8-16 x 1 ½ bolt Aluminum plate to body 6 9937001 3/8-16 Nylok nut Aluminum plate to body 1 99373003 3/8 SAE washer Aluminum plate to body 9950109 ½ -13 x 6 ½ Bolt Lower Shock Mount to Shock 9950300 ½ Split Lock Washer Lower Shock Mount to Shock 1 900063 Red Loctite Tube Lower Mount Assembly
Mopar LX Front ShockWave Assembly Item Number 1 3 4 5 6 Description 55 (6.5 ) bellow assembly 4090199 Short stud top 90009986 Washer for Rubber Mount 90009 Lower Rubber Isolator(Tshaped)90001973 Upper mounting plate 90001971 Upper Rubber Isolator 90001974 Qty. 4 7 9/16 X 3 ½ or 4 Bolt 8 9/16 SAE Nylok nut 9 9/16 SAE jam Nylok nut 11 13 14 15 Locking Ring 70008913 Bottom lower billet mount 90001668 Aluminum Reducer Puck 9000357 Lower Steel Shockwave Bracket-90009980 17 ½ -13 x 6 ½ USS bolt 18 ½ Lock Washer 19 5. Shock w/ universal bottom - 4559999 1 Set Screw
Installation Instructions 1. Raise the vehicle to a safe and comfortable working height with the suspension hanging freely.. Remove the factory struts and upper mounts; refer to the service manual for proper disassembly procedures. 3. Due to possible lower mount options on this platform, included in the kit are different widths of lower mounts. 4. Determine the width of Lower Mount required for your application by test fitting the supplied mounts. Refer to the diagram below for assembly and clocking of the lower bracket. 1. Shock Assembly. Lower Shock Adapter 3. Lower Shock Mount 4. ½ Split Lock washer 5. ½ x 6 ½ Hex Bolt Assembly 1. Slide the Shock Adapter onto the Shock Assembly.. Install the Split Lock washer onto the ½ x 6 ½ Bolt. 3. Apply Red Loctite onto the threads of the bolt. 4. Insert the Bolt through the Lower Shock Mount and into the bottom hole of the Shock Adapter. 5. Thread the bolt into the Shock. The Lower Shock Mount has to be clocked so that the Shock Mount Tabs run parallel with the Sway Bar Mount on the Adapter. The diagram here shows correct clocking of the bracket. 6. With the bracket clocked correctly, tighten the ½ Bolt.
5. Bolt the aluminum upper plate to the car in place of the factory rubber mount using the 3/8 x 1 ¼ bolts, flat washer and Nylok nuts. Note: The recessed side of the plate must face down. 6. Place one of the.375 steel washers over the threaded stud. Then slide the T shaped rubber bushing over the stud. Place the Shockwave into the coil spring pocket with the stud protruding through the hole in the aluminum plate. 7. From the engine bay, place the other rubber bushing over the stud, then another steel plate. Secure the assembly with a 9/16 SAE Nylok Jam nut. Note: Some cars may have a plastic cover in the engine bay that may need to be clearance for the adjustment knob. 8. With the Sway Bar tab pointing to the inside of the car, Bolt the bottom of the Coilover assembly to the lower arm using a 9/16 x 3 ½ bolt and Nylok nut. 9. Attach sway bar to Shockwave using the factory hardware.
10. Apply thread sealant to an elbow air fitting and screw it into the top of the Shockwave. 11. Route the airline. Allow slack for suspension movement. 1. Check air spring clearance through full suspension travel. Allowing the Shockwave to rub on anything will result in air spring failure and in not a warrantable situation. 13. Ride height on this car is approximately lower than factory. On most vehicle this will occur around 100psi, but will vary per vehicle. The care and feeding of your new ShockWaves 1. Although the ShockWave has an internal bumpstop, DO NOT DRIVE THE VEHICLE DEFLATED RESTING ON THIS BUMPSTOP. DAMAGE WILL RESULT. The internal bumpstop will be damaged, the shock bushings will be damaged, and the vehicle shock mounting points may be damaged to the point of failure. This is a non warrantable situation.. Do not drive the vehicle overinflated or topped out. Over a period of time the shock valving will be damaged, possibly to the point of failure. This is a non warrantable situation! If you need to raise your vehicle higher that the ShockWave allows, you will need a longer unit. 3. The ShockWave is designed to give a great ride quality and to raise and lower the vehicle. IT IS NOT MADE TO HOP OR JUMP! If you want to hop or jump, hydraulics are a better choice. This abuse will result in bent piston rods, broken shock mounts, and destroyed bushings. This is a non warrantable situation. 4. Do not let the ShockWave bellows rub on anything. Failure will result. This is a non warrantable situation. 5. The ShockWave product has been field tested on numerous vehicles as well as subjected to many different stress tests to ensure that there are no leakage or durability problems. Failures have been nearly nonexistent unless abused as described above. If the Shockwave units are installed properly and are not abused, they will last many, many years. ShockWave units that are returned with broken mounts, bent piston rods, destroyed bumpstops or bushings, or abrasions on the bellows will not be warrantied.
Components: 90006781 67c air spring Part # 13044099 Mopar LX Rear CoolRide Kit 1 90000713 Driver side upper air spring mount 1 90000714 Passenger side upper air spring mount 90000715 Lower air spring plate Hardware: 10 993700 3/8 USS Nylok nut Air spring mounts 4 99371003 3/8 x 1 USS bolt Upper air spring mount to car 4 99371017 3/8 x 3/4" button head Air spring to lower plate/ lower plate to arm 99373005 3/8 lock washer Air spring to lower plate 16 99373003 3/8 SAE flat washer Air spring mounts 99431001 7/16 x 1 USS bolt Lower plate to arm 9943300 7/16 SAE flat washer Lower plate to arm 99433003 7/16 lock washer Lower plate to arm
Installation Instructions 1. Raise the vehicle to a safe and comfortable working height with the suspension hanging freely.. Remove the factory shock absorbers and coil spring. Refer to a factory service manual for proper disassembly procedures. 3. Bolt the air spring to the lower plate use the 3/8 x 3/4 button head bolt, lock washer and flat washer. 4. Apply thread sealant to an elbow air fitting and screw it into the top of the air spring. 5. Fasten the upper mount to the air spring using two 3/8 Nylok nuts and flat washers. 6. The hole being tapped in the picture will be used to bolt the lower air spring plate; a 7/16 x 1 bolt, flat washer and lock washer will be used. A 7/16 USS tap will be needed. 7. The inside hole on the plate will fastened with a 3/8 x 1 button head. The button head must be used, a hex bolt could rub the air spring and cause failure. There is an existing hole in the lower arm.
8. Hold the air spring assembly up to the coil spring pocket. Using a camp to hold the bracket in place; center punch and drill the two mounting holes. 9. Secure the assembly with two 3/8 x 1 bolts, Nylok nuts and flat washers. Note: The air line must be routed at this time. 14. Double-check air spring clearance through full suspension travel. Allowing the air spring to rub will cause air spring failure and is not a warrantable situation. 15. Ride height on this air spring is 5 tall. This will be achieved at around 100psi but will vary to driver preference & vehicle weight.
Components: Part # 13040709 Mopar LX Rear RQ Series Shock Kit 4 9000443 Aluminum spacers for lower bearing 4 9000043 Aluminum T-bushing for upper bearing 9000161 Upper shock bracket 900030 Upper shock bracket washer 90001976 Bushing sleeve (Pressed into factory bushing) RQ Series shocks (includes the following) 4079999 7 stroke RQ Series shock 900003 4 Eyelet 4 90001994.65 I.D. bearing (installed into shock body) 8 90001995 Bearing snap ring Hardware: 99501003 ½ x ½ USS bolt Shock to upper bracket 9950001 ½ USS Nylok nut Shock to upper bracket 4 99501004 ½ x 3 USS bolt Shock mounts 4 9950001 ½ USS Nylok nut Shock mounts 99503004 ½ Fender washer Shock bracket to factory mount
Installation Instructions 1. Raise the vehicle to a safe and comfortable working height with the suspension hanging freely.. Remove the factory shock absorbers and coil spring. Refer to a factory service manual for proper disassembly procedures. 3. Press the 1.6 bushing sleeve into the oem rubber shock mount. 4. Bolt the upper shock mount to rubber oem mount using the ½ x 3 bolt, Nylok nut and fender washer. The plate must be installed between the bracket and the rubber bushing. 5. Using a ½ x ½ bolt and Nylok nut, fasten the top of the shock to the upper mount. The shock body should be mounted on top. One aluminum T-bushing must be installed on each side of the bearing. 6. Bolt the eyelet to the lower control arm using the 1/" x 3 bolt and Nylok nut. The thicker aluminum spacer must be installed on each side of the bearing.
Part # 30154000 4000 Series RidePro 4 Way Compressor System 3 Gallon Tank Analog Gauges Components: 1 319000 Thomas 319 Compressor 1 31194000 RidePro 4 Way analog control panel with rocker switches (Black Face) 1 31913100 3 gallon aluminum tank 1 31934001 RidePro 4 Way valve block 1 31980005 Pressure switch 135 On / 150 Off Wiring: 1 319000 30 amp relay 1 9000194 Fuse holder 1 900019 0 Amp fuse 31900036 Wiring harness - Control panel to valve 3 99104001 10-4 x 1 phillips screw 3 991000 10-4 Nylok nut 3 99103001 #10 SAE flat washer 1 90001916 #10 x 5/16 ring terminal 1 90001913 1-10 butt connector 90001918 Female spade connector Airline & Fittings: 3194000 1/4 DOT airline - 30 ft. roll - valve block to gauges 31940000 1/8 DOT airline - 5 ft. roll - valve block to gauges 1 3195150 1/8 npt x 1/4 tube female straight - compressor 1 31957003 Brass Nipple - compressor 6 3195401 1/4 npt x 1/4 tube Elbow airline fitting 7 31954000 1/4 npt x 1/4 tube Straight airline fitting 4 3195000 1/8 npt x 1/8 tube Straight fitting - manifold to gauge fitting 1 31957004 1/4 npt plug - plug unused supply port 1 31959301 1/4 npt check valve
ARC4000 Compressor System Instructions These are some general guidelines to follow when installing your new RidePro air control system. Depending on the vehicle there are many different ways to plumb the system. Start out by planning a lay out of where you want everything to be mounted. Typically we try to keep the compressor, solenoids, tank, and sending units in a central location, but they can be separated to suit your needs. Mounting the Compressor/ Pressure Switch Remove the negative battery cable before beginning installation. All of our compressors are sealed for moisture and dust resistance so they can be mounted anywhere on the vehicle. Although it is best to mount it in a place out of direct contact with rain and snow. It is OK to mount it underneath the vehicle but keep it inside the frame rails away from water and debris thrown off the tire. This is a dry compressor; therefore it is maintenance free and can be mounted in any position. It is best if mounted to something solid to reduce vibration and noise. If mounting it to sheet metal or the bed of a truck, use sound deadening material between the compressor and the mounting surface. Use the rubber grommets supplied on the feet of the compressor to reduce vibration. A template is supplied to aid in drilling the holes. Check template with compressor before drilling the holes. Apply thread sealant to the pressure switch and compressor T and screw into the tank. One spade of the pressure switch will connect to power the other to the red wire on the compressor. Mounting the Air Tank The air tank can be mounted anywhere on the vehicle in any position. A template is supplied to aid in drilling the holes. Check the template with the tank before drilling the holes. If your air system is used frequently you may want to remove the tank once a season to drain any excessive accumulation of water.
Mounting the RidePro Air Valves The valves, like the compressor, are sealed and can be mounted in the same locations. Although if the vehicle will be exposed to freezing temperatures it is a good idea to mount them in the engine bay if possible to reduce the possibility of freezing. They can be mounted in any position. Mount the valves higher than the tank to avoid moisture build up. This could cause the air pressure sensors to give a faulty reading. Attach the ground strap to a good, clean ground (preferably the frame). The exhaust port will be left open. The valve is held closed with the pressure in the tank. If tank pressure drops below air spring pressure they will equalize deflating all 4 air springs. Wiring Harness Red Wire- The red wire on the harness will connect to 1 volt switched. Gray Wire- This power for the light in the switch- this wire goes to the light circuit(dash lights) of the vehicle. This wire needs 1 volt when the lights are on or the key is on. The gauge light should be hooked to the same circuit as this wire. Black Wire- This wire is ground for the light in the switch. It goes to a good ground. Routing the Airline and Fittings Make all airline cuts with a razor or tubing cutter. It must be clean and straight or it will not seal. All fittings are DOT approved push-to-connect style. They are very simple to use and are reusable. Firmly push the airline into the fitting to attach. To release the airline pull the collar on the fitting back towards the fitting and pull the airline out. Use thread sealant on all fittings. Do not over tighten the fittings. This could result in breaking the fitting or damaging the air spring. All of our airlines are DOT approved so they are very strong. But keep them away from any sharp edges. Also when passing through a hole in the frame use a grommet. Keep away from intense heat including mufflers and exhaust manifolds. Use zip ties or other fasteners to secure the airline. Illumination (Gray) - This wire provides power to the switch lights. It should be hooked up to a light circuit in the vehicle (dash lights) or it can be hooked up to a 1 volt switched source. +1V (Red) - This wire is the main power for the valves. It should be hooked up to a 1 volt switched circuit. It needs 1 volt with the key on and should have no power with the key off. Ground (Black) This wire provides ground to the switch lights. It should be hooked up to a good ground source. Note: The Illumination and Ground wires do not have to be hooked up for the switches to work. They do have to be hooked up for the lights in the switches to work.