Pilot Operated Port Solenoid Valve for Dry Air Series VQ0/30 Compact and lightweight with large flow capacity VQ0 Mass (g) 46 80 C [dm 3 /(s bar)].5 (C8) 3.0 (C) Series VQ0 High frequency operation possible High speed response 7 ms or less (VQ0), 0 ms or less () Series (High speed response type without light/surge voltage suppressor at the supply pressure of 0.5 MPa) Long operating life VX VXD VXZ VXE VXP VXR VXH VXF VX3 VXA VCH VDW VQ LVM VCA VCB VCL VCS VCW Easy piping with One-touch Fittings Dusttight low jetproof enclosure (IP65) compliant in DIN terminal type. Application: Air-blow, Blow-off of workpiece, etc. 67
Pilot Operated For Dry Air Port Solenoid Valve Series VQ0/30 Single Unit How to Order Valves VQ A G C6 Series/ Orifice diameter Symbol 3 Series VQ0 Valve type N.C. (A) (P) Option : None F: With bracket CE compliant Q CE compliant Made to order specifications (Refer to the table below) A: Single unit Body type Manual override None Note) Slotted locking type B (tool required) Note) Only normally closed DIN terminal in-line style is applicable. L: Type L (VQ0 only) Note) If ordering both options, indicate LF. M: For manifold 3 5 6 Note ) 9 Coil voltage 00 VAC (50/60 Hz) 00 VAC (50/60 Hz) 0 VAC (50/60 Hz) 4 VDC VDC Other special voltage Note ) Please consult with SMC for special voltages. Note ) There is polarity for DC voltage (with powersaving circuit type). Electrical entry G: Grommet Electricity circuit Symbol DC voltage Z H With power-saving circuit (With surge voltage suppressor protection circuit) With power-saving circuit (With light/surge voltage suppressor protection circuit) High speed response type (Without energy-saving, light/surge voltage suppressor circuit) Note) H is available only for DC voltage and cannot be energized continuously. Note) Made to Order Specifications Oil-free specifications VQ A 3M Port size Symbol Port size C6 One-touch fitting for ø6 C8 One-touch fitting for ø8 C0 One-touch fitting for ø0 C One-touch fitting for ø AC voltage With full wave rectifier circuit (With surge voltage suppressor protection circuit) With full wave rectifier circuit (With light/surge voltage suppressor protection circuit) X VQ0 Please contact SMC for further specifications, delivery and price. Note) Please consult with SMC when using. Not available for manual operation. Made to Order Y: DIN terminal YO: DIN terminal without connector Seal material fluororubber specifications VQ A 3M X5 Seal material fluororubber/oil-free specifications VQ A 3M X3 Note) Not available for manual operation. 68
Pilot Operated Port Solenoid Valve for Dry Air Series VQ0/30 Standard Specifications JIS Symbol (A) (P) N.C. VQ0 Valve specifications Electric specifications Series Valve construction Fluid Ambient and fluid temperature Lubrication Manual override Shock resistance/vibration resistance Enclosure Internal leakage cm 3 /min Exterior leakage cm 3 /min Mounting orientation Mass Coil rated voltage Allowable voltage fluctuation Coil insulation type Power DC voltage (with power-saving circuit) consumption DC voltage (without power-saving circuit) (Current value) AC Electrical entry VQ0 port poppet pilot operated Note ) Air/Inert gas Note ) 0 to 50 C Not required Note 3) Slotted locking type (tool required) 50/30 m/s Note 4) Note 5) Dustproof 5 or less 5 or less Unrestricted 46 g 80 g VDC, 4 VDC, 00 VAC, 0 VAC, 00 VAC ±0% of rated voltage Class B or equivalent Inrush:.9 W, Holding: 0.6 W.9 W VA Grommet, DIN terminal Note ) This product is for dry air. Use in clean air, and be sure that drain and oil content does not flow into the product. Note ) Use dry air to prevent condensation when operating at low temperatures. Note 3) Manual override is available only for DIN terminal type. Note 4) Vibration resistance: No malfunction occurred in a one-sweep test between 8.3 and 000 Hz. Test was performed at both energized and de-energized states to the axis and right angle directions of the main valve and armature (value at the initial state). Shock resistance: No malfunction resulted from the impact test using a drop impact tester. The test was performed on the axis and right angle directions of the main valve and armature for both energized and de-energized states (value at the initial state). Note 5) DIN terminal type: Applicable to dusttight and low jetproof (IP65). Characteristic Specifications Series Port size Flow C [dm 3 /(s bar)] characteristics b C6.4 0.3 VQ0 C8.5 0.4 C0.8 0.4 C 3.0 0.37 VX VXD VXZ VXE VXP VXR VXH VXF VX3 VXA VCH VDW VQ LVM VCA Construction Cv 0.33 0.39 0.80 0.8 Min. operating pressure differential 0.0 MPa Note 3) Max. operating pressure differential 0.6 MPa 0.5 MPa Note ) Note ) Electricity circuit With power-saving circuit High speed response type With power-saving circuit Note ) High speed response type Response ON 0 ms or less 7 ms or less 5 ms or less 0 ms or less time OFF 5 ms or less 5 ms or less 5 ms or less 5 ms or less Note ) JIS B 8375 (value of DC voltage specifications at 0.5 MPa supply pressure) (Value of high response time is subject to change upon pressure, quality of air.) Note ) It cannot be used when energized continuously. Note 3) If a restrictor (nozzle, etc.) is mounted on the outlet side piping, the pressure differential when ON is smaller. Be sure that the pressure differential does not drop below 0.0 MPa. VCB VCL VCS VCW w e q r t y u Component Parts No. 3 4 5 6 7 Description Solenoid coil Body Fixed armature Armature Return spring Poppet Diaphragm assembly Material Resin Stainless steel Stainless steel Stainless steel NBR H NBR, Resin 69
Series VQ0/30 Dimensions: Series VQ0 In-line Type: Grommet (G) VQA-G- - Mounting holes x ø3. through Bracket mounting holes x ø3. through Light Lead wire length Approx. 300 P port C6: One-touch fitting for ø6 C8: One-touch fitting for ø8 C6: One-touch fitting for ø6 C8: One-touch fitting for ø8 Dotted line: Bracket mounting style (-F) 70
Pilot Operated Port Solenoid Valve for Dry Air Series VQ0/30 Dimensions: Series VQ0 Type L: Grommet (G) VQA-G- -L VX VXD VXZ Light VXE VXP VXR Lead wire length Approx. 300 VXH VXF VX3 VXA VCH VDW VQ P port C6: One-touch fitting for ø6 C8: One-touch fitting for ø8 LVM VCA VCB VCL C6: One-touch fitting for ø6 C8: One-touch fitting for ø8 VCS VCW x ø3. mounting hole Dotted line: Bracket mounting style (-LF) 7
Series VQ0/30 Dimensions: Series VQ0 In-line Type: DIN terminal (Y) VQA-Y- - Mounting hole x ø3. through Bracket mounting hole x ø3. through Manual override Applicable cable O.D. ø3.5 to ø7.0 mm P port C6: One-touch fitting for ø6 C8: One-touch fitting for ø8 C6: One-touch fitting for ø6 C8: One-touch fitting for ø8 Dotted line: Bracket mounting style (-F) 7
Pilot Operated Port Solenoid Valve for Dry Air Series VQ0/30 Dimensions: Series In-line Type: Grommet (G) VQ3A-G- - Mounting hole x ø4.3 through Bracket mounting hole x ø4.5 through VX VXD VXZ VXE VXP Light VXR VXH VXF VX3 VXA Lead wire length Approx. 300 VCH P port C0: One-touch fitting for ø0 C: One-touch fitting for ø C0: One-touch fitting for ø0 C: One-touch fitting for ø VDW VQ LVM VCA VCB VCL VCS VCW Dotted line: Bracket mounting style (-F) 73
Series VQ0/30 Dimensions: Series DIN terminal (Y) VQ3A-Y- - Mounting hole x ø4.3 through Bracket mounting hole x ø4.5 through Manual override Applicable cable O.D. ø3.5 to ø7.0 mm P port C0: One-touch fitting for ø0 C: One-touch fitting for ø C0: One-touch fitting for ø0 C: One-touch fitting for ø Dotted line: Bracket mounting style (-F) 74
Pilot Operated Port Solenoid Valve for Dry Air Series VQ0/30 How to Order Manifold VVQ 08 3 Series VQ0 Stations 0 station 0 0 stations Option D DO How to Order Valves (For Manifold) Series/ Orifice diameter Symbol Series VQ0 3 Valve Type N.C. (A) (P) Valve specifications M Manifold Electrical entry G Y YO P port/thread type 00N 00T 00F CE compliant Rc 3/8 NPT 3/8 NPTF 3/8 G 3/8 None DIN rail mounting DIN rail mounting (Without DIN rail) VQ M G C6 Grommet DIN terminal DIN terminal (without connector) 3 5 6 Note ) 9 Coil voltage 00 VAC (50/60 Hz) 00 VAC 0 VAC 4 VDC VDC Other special voltage Q Note ) Please consult with SMC for special voltages. Note ) There is polarity for DC voltage (with power-saving circuit type). Electricity circuit Symbol Z H Note) CE compliant DC voltage With power-saving circuit (with surge voltage suppressor protection circuit) How to Order Manifold Assembly Enter the mounting valve and option part numbers under the manifold base part number. <Ordering Example> VVQ-05 set Manifold part No. VQM-5G-C6 4 sets Valve part No. (Stations to 4) VQM-5G-C8 set Valve part No. (Station 5) is the symbol for assembly. Add a in front of the part numbers for solenoid valves, etc., to be mounted. Port size Symbol C6 C8 C0 C With power-saving circuit (with light/surge voltage suppressor protection circuit) High speed response type (without energy-saving, light/surge voltage suppressor circuit) U side D side P Stations 3 Enter together in order, counting from station on the D side. Made to order specifications Q (Refer to the table below) Port size One-touch fitting for ø6 One-touch fitting for ø8 One-touch fitting for ø0 One-touch fitting for ø VQ0 Manual override None B Note) Slotted locking type (tool required) Note) Only normally closed DIN terminal in-line style is applicable. CE compliant AC voltage With full wave rectifier circuit (with surge voltage suppressor protection circuit) Note) H is available only for DC voltage and cannot be energized continuously. CE compliant With full wave rectifier circuit (with light/surge voltage suppressor protection circuit) VX VXD VXZ VXE VXP VXR VXH VXF VX3 VXA VCH VDW VQ LVM VCA VCB VCL VCS VCW Made to Order Specifications Please contact SMC for further specifications, delivery and price. Made to Order Oil-free specifications VQ 3 M X Note) Please consult with SMC when using. Not available for manual operation. Seal material fluororubber specifications VQ 3 M X5 75
Series VQ0/30 Dimensions Plug lead unit manifold (VVQ- ) Mounting hole x ø4.5 through C6: One-touch fitting for ø6 C8: One-touch fitting for ø8 x Rc 3/8 DIN rail mounting 4 x M3 x 0.5 Dotted line: DIN rail mounting (-D) Dimensions L L L L3 L4 L5 n 3 4 5 6 7 8 9 0 78 68 00 0.5 66.8 07 97 37.5 48 95.8 36 6 6.5 73 4.8 65 55 87.5 98 53.8 94 84.5 3 8.8 3 3 50 60.5.8 5 4 75 85.5 40.8 8 7 300 30.5 69.8 49 39 75 85.5 37.8 30 300 337.5 348 98.8 Formulas L = (n ) x 9 + 49 L = L 0 L3 = L4 0.5 L5 = L. n: Station (Max. 0) 3 4 5 6 7 8 9 0 339 368 397 46 455 484 53 54 57 600 39 358 387 46 445 474 503 53 56 590 36.5 387.5 45 450 475 500 537.5 56.5 587.5 65 373 398 435.5 460.5 485.5 50.5 548 573 598 635.5 37.8 356.8 385.8 44.8 443.8 47.8 50.8 530.8 559.8 588.8 76
Pilot Operated Port Solenoid Valve for Dry Air Series VQ0/30 Dimensions Plug lead unit manifold (VVQ3- ) Mounting hole x ø4.5 through C0: One-touch fitting for ø0 C: One-touch fitting for ø DIN rail mounting 4 x M3 x 0.5 x Rc 3/8 VX VXD VXZ VXE VXP VXR VXH VXF VX3 VXA VCH VDW VQ LVM VCA VCB VCL VCS VCW Dotted line: DIN rail mounting (-D) Formulas L = (n ) x 37 + 56 L = L 0 L3 = L4 0.5 L5 = L. Dimensions n: Station (Max. 0) L n 3 4 5 6 7 8 9 0 3 4 5 6 7 8 9 0 L L L3 L4 L5 56 46 75 85.5 44.8 93 83.5 3 8.8 30 0 50 60.5 8.8 67 57 87.5 98 55.8 04 94 5 35.5 9.8 4 3 6.5 73 9.8 78 68 300 30.5 66.8 35 305 337.5 348 303.8 35 34 375 385.5 340.8 389 379 4.5 43 377.8 46 46 450 460.5 44.8 463 453 487.5 498 45.8 500 490 55 535.5 488.8 537 57 56.5 573 55.8 574 564 587.5 598 56.8 6 60 65 635.5 599.8 648 638 66.5 673 636.8 685 675 700 70.5 673.8 7 7 737.5 748 70.8 759 749 775 785.5 747.8 77
Series VQ0/30 Single Unit Option Bracket assembly (with mounting screws) For fixing this solenoid valve. Type VQ0 Grommet in-line type VQ0 Grommet L type, DIN terminal type DIN terminal L type Bracket assembly AXT835-3A AXT835-3A- AXT835-3A-3 AXT837-3A (Mounting screws, pcs.) M3 x 45 M3 x 40 M3 x 35 M4 x 45 Manifold Option DIN rail AXT00-DR- L.5 (Pitch) 5.5 7.5 Suffix the number from DIN rail dimensions table below. Refer to the dimension drawing for each manifold for L dimension. 5.5 35 5 Each manifold can be mounted on a DIN rail. Order with the option symbol -D to specify DIN rail mounting style. The DIN rail is approximately 30 mm longer than the length of manifold. L dimension Series VQ0.5 Stations No. 6 8 3 4 3 5 5 6 7 7 0 8 9 4 0 7 9 3 3 34 4 36 5 38 6 40 7 43 8 45 9 47 0 50 L 85.5 0.5 48 73 98 3 60.5 85.5 30.5 348 373 398 435.5 460.5 485.5 50.5 548 573 598 635.5 Series Stations No. L 3 4 5 6 7 8 9 0 3 4 5 6 7 8 9 0 6 85.5 9 3 60.5 5 8 98 35.5 4 73 30.5 7 30 348 385.5 33 36 43 460.5 39 4 498 535.5 45 573 47 50 598 635.5 53 56 673 70.5 59 6 748 785.5 DIN rail mounting bracket VVQZ00-DB-5 This bracket is used for mounting the manifold on the DIN rail. DIN rail mounting bracket is attached on the manifold. set of DIN rail mounting brackets for manifold includes brackets. Blanking plate assembly (with O-ring and mounting screws) Mount a blank plate on valve manifold when a valve is disassembled for maintenance purposes, or when spare valve unit is supposed to be mounted in the future. Series VQ0 Blanking plate assembly AXT835-35A AXT837-35A (O-ring) OR-679-00-H OR-400-50-H (Mounting screws, pcs.) M3 x 6 M4 x 6 78
Series VQ0/30 Specific Product Precautions Be sure to read before handling. Refer to front matters 4 and 43 for Safety Instructions, and pages 7 to 9 for Port Solenoid Valves for Fluid Control Precautions. Warning Warning Selection. Air quality This product is for dry air. Drain, oil, etc. in the air may result in faulty operation. Use clean (dry) air.. Pressure differential If a restrictor (nozzle, etc.) is mounted on the outlet side, the outlet side pressure differential at the inlet side is smaller. Be sure the pressure differential when ON does not drop below 0.0 MPa. Manual Override Regardless of electric signals to the solenoid valve, the manual override is used for switching the main valve. (DIN terminal only.) Push the manual override Slotted locking type (tool required) button with a small flat head screwdriver until it stops. Turn it in the counterclockwise direction at ø3.8 90 to lock the manual. Turn it right to release. PUSH TURN LOCK Connection and Electrical Circuit Caution Black ( ) DC Blue (00 VAC) Red (00 VAC) Red (+) DC Blue (00 VAC) Red (00 VAC) With DC voltage power-saving circuit (with polarity) Lead wire color Red DIN connector (+) LED Timer circuit SOL Caution Power wave form of power-saving type (Rated voltage at 4 VDC) AC circuit Connection and Electrical Circuit 4 V 0 V 0 to 0 ms.9 W 0.6 W 0 W Lead wire color DIN connector Blue (00 VAC), Red (00 VAC) Blue (00 VAC), Red (00 VAC) Caution Applied voltage Power-saving Valve Mounting When mounting the valve, secure with brackets. When mounting it directly, tighten the mounting screws with the appropriate torque (0.7 to 0.8 N m). Mounting screw Tightening torque 0.7 to 0.8 N m LED When Energizing Continuously for Long Period of Time SOL Caution When energizing continuously, choose the option of an energysaving circuit specifications. High speed response type (with no energy-saving circuit) cannot be energized continuously. VX VXD VXZ VXE VXP VXR VXH VXF VX3 VXA VCH VDW VQ LVM VCA VCB VCL VCS VCW Black ( ) i i i: Inrush current, i: Holding current DC (with power-saving circuit) specifications is designed to reduce the power consumption at holding to achieve power-saving by circuit shown above. Refer to below power wave form. 79
Series VQ0/30 Specific Product Precautions Be sure to read before handling. Refer to front matters 4 and 43 for Safety Instructions, and pages 7 to 9 for Port Solenoid Valves for Fluid Control Precautions. How to Wire DIN Terminal Caution ISO#: Based on DIN 43650C (Pin gap 8 mm) Connection. Loosen the tightening screw and pull the connector off of the solenoid valve.. After removing the tightening screw, divide the terminal block and housing by prying open the slot area of the lower part of the terminal block open with a screwdriver. 3. Loosen the terminal screws of the block and insert stripped lead wires in accordance with the wiring diagram. Secure each wire by re-tightening the terminal screw (In the case of terminal : (+), : (-) DC) 4. Tighten the ground nut to secure the cable wire. Change of electrical entry Wire entry can be changed by mounting the housing in either direction (four directions at every 90 ) after dividing the terminal block and the housing. For the indicator lighted style, be careful not to damage the light with the lead wire of the cable. Precautions Insert a connector straight or pull it out straight, using caution it does not be tilted. Applicable cable Cord O.D.: ø3.5 to ø7 (Reference) 0.5 mm -core and 3-core wire equivalent to JIS C 3306. Ground nut Tightening torque.65 to.5 N m Washer Grommet (Rubber) (Voltage symbol) Refer to the following table Tightening torque 0. to 0.5 N m Terminal screw (3 positions) Tightening screw Tightening torque 0.3 to 0.4 N m Housing (Position for light mounting) Terminal block Shaved part DIN Terminal Part No. (Based on DIN) Without indicator light SY00-8-4 With Indicator Light Rated voltage Voltage symbol Part no. 4 VDC VDC 00 VAC 00 VAC 0 VAC 4 V V 00 V 00 V 0 V SY00-8-3-05 SY00-8-3-06 SY00-8--0 SY00-8--0 SY00-8--03 Manifold How to Mount/Remove from DIN Rail Caution Removing procedure. Loosen the clamp screw on the A side of both ends of the manifold.. Lift the A side of the manifold off the DIN rail and slide it in the direction of the arrow. Mounting procedure. Hook the mounting hook on the B side of the manifold base to the DIN rail.. Press down side A and mount the end plate on the DIN rail. Tighten the clamp screw on side B of the end plate. How to Wire DIN Terminal DIN Terminal Circuit with Indicator Light AC circuit NL R NL: Neon light R: Resistor (Tightening torque: 0.3 to 0.4 N m). Caution Valve Mounting DC circuit LED R LED: Light emitting diode R: Resistor After confirming the gasket is correctly placed under the valve, tighten the mounting screws with the appropriate torque (0.7 to 0.8 N m). A B Manifold mounting screw Manifold mounting screw 80