Vehicle Technology Division THE NETHERLANDS (N E D E R L A N D) COMMUNICATION Concerning (1) : - approval granted - approval extended - approval refused - approval withdrawn - production definitely discontinued of a type of retro reflecting device pursuant to Regulation number 3. Approval number: E4-3R-023638 Extension number: 00 Approval mark IA 02 3638 1. Trade name or mark of the device : STANLEY 2. s name for the type of device 3. s name and address 2-9-13, Nakameguro, Meguro-Ku, Tokyo, Japan 4. If applicable, name and address of the manufacturer s representative : not applicable 5. Submitted for approval on : July 08, 2013 6. Technical service responsible for conducting approval tests : Am Grauen Stein D-51105 Köln (Poll) 7. Date of test report : July 11, 2013 8. Number of test report : 82-R3-38955/13 P.O. Box 777 Tel. + 31 (0)79 345 81 43 Vehicle Approval and Information 2700 AT Zoetermeer Fax + 31 (0)79 345 80 43 The Netherlands www.rdw.nl Lamps-reflectors R3-02 v2.00 Page 1 of 2
Approval number: E4-3R-023638 Extension number: 00 9. Concise description In isolation / part of an assembly of devices (1) Colour of light emitted : white / red / amber (1) Installation as an integral part of a lamp which is integrated into the body of a vehicle Geometric conditions of installation and relating variations, if any : yes / no (1) : see annexed drawing 10. Position of the approval mark : on the lens 11. Reason(s) for extension (if applicable) : not applicable 12. Approval : granted / refused / extended / withdrawn (1) 13. Place : Zoetermeer 14. Date : 15. Signature : 16. The following documents, bearing the approval number shown above, are available on request: - Test report 82-R3-38955/13 (7 pages) - Information document W1382-0 (2 pages) (1) Strike out what does not apply. Lamps-reflectors R3-02 v2.00 Page 2 of 2
TEST REPORT according to ECE-Regulation Uniform provisions concerning the approval of retroreflecting devices for power-driven vehicles and their trailers ECE-R3 including all amendments until series of amendments: 02 Supplement 12 Previously granted ECE - certificate : --- Page 1 of 7
0 Test object(s) and general test information 0.1 Test object(s) identification number version : --- 0.2 General test information 0.2.1 Order issued by (if different from manufacturer) : --- 0.2.2 Test object / vehicle received on : not applicable 0.2.3 Test date : July 08, 2013 0.2.4 Test site : Stanley, Hadano, Japan 0.2.5 Remark : The results of the test refer exclusively to the object(s) mentioned under point 0.1 of this report. Page 2 of 7
1 Test minutes 1.1 Test facilities : The test facilities are in compliance with the requirements of the regulation. 1.2 Test results 1.2.1 Temperature : 24 C 1.2.2 Markings : The trademark is marked clearly legible and indelible on the lens. Space for the approval mark and for additional symbols is provided on the lens. 1.2.3 General specifications : The retro reflector is designed and made that under normal use their satisfactory operation is ensured and they retain the required characteristics. 1.2.4 Special tests : see appendix 1 1.2.5 Photometric tests : see appendix 1 The components are not capable of being easily dismantled, and the optical unit is not replaceable. The test samples have been tested in the chronological order indicated in Annex 12 of the Regulation, and in accordance with the test procedure stated in Annex 4 of the Regulation. 1.2.6 Illuminating surface : See the drawing of the information document. 1.3 Explanatory note : not applicable Page 3 of 7
2 Remark concerning tested object(s) All versions of the lamps as stated in the information document are covered with the tested version(s) and test object(s) respectively. 3 Appendices 0 List of modifications 1 Test results Information folder -0 4 Statement of conformity The information folder and the type described therein comply with the requirements in the abovementioned regulation. The test report is comprised of pages 1 to 7 (including appendices 0 and 1) and shall not be reproduced except in full, without the written approval of the test laboratory. Cologne, July 11, 2013 AHA A. Hayashi Page 4 of 7
List of modifications Appendix 0 Correction of : - --- Modification of : - --- Addition of : - --- Deletion of : - --- Page 5 of 7
Test results Appendix 1 Results of special tests of retro reflector, class IA number of Annex test test samples result of examination remark 5 shape and dimensions all complying 10 heat all complying 6 colorimetry all complying colour of the light reflected : white / red /amber 7 photometry all complying 20, V=H=0 7 photometry c and d see next page complete 8.1 water penetration g and h complying (for class IA) moisture and dust exposure g and h complying (for class IB) 8.3 motor fuels g and h complying 8.4 oils g and h complying 4 colorimetry g and h complying photometry g and h complying 20, V=H=0 8.2 corrosion e and f --- not applicable abrasive strength e and f --- *) 9 stability of optical properties with --- --- not examined ageing 11 colour fastness --- --- not examined *) Remark : the device does not incorporate any metal component, the rear face of the device is not accessible Page 6 of 7
Results of photometric tests of the reflex reflector class IA coefficients of luminous intensity (CIL) in accordance with Annex 7 of the Regulation distribution of the intensity of the retro reflector in [mcd/lux] sample 1 sample 2 required horizontal angle L20º V R20º L20º V R20º min. vertical angle U10º 639 1291 200 U5º 372 337 1031 678 100 =20' H 622 1489 300 D5º 346 334 866 700 100 D10º 445 1302 200 vertical angle U10º 26.7 16.3 2.8 U5º 18.1 16.7 12.3 10.1 2.5 =1 30' H 35.9 37.0 5 D5º 19.1 15.8 16.5 12.5 2.5 D10º 27.8 22.6 2.8 Page 7 of 7