Underwater LED Light to 60 meters - Aluminum Housing - 12 Watts - 720 Lumens - 10 Inch Cable Part #: LEDEUL4-10ST Made in the USA NSN for this product: 6210-01-647-7649, Light Emitting Diode The LEDEUL4-10ST Underwater LED light from Larson Electronics produces 800 lumens of light while drawing only 12 watts @1 amp on a 12 volt electrical system. This powerful and compact underwater LED light features a safer and more durable through-hole surface mounting alternative to other units which require drilling large mounting holes in the hull and complex sealing. This underwater light is equipped with 10" of power cable, stripped and tinned for easy installation. The LEDEUL4-10ST underwater LED light produces 800 lumens of bright light, more than 55 watt halogens, and is available in white, blue, green, or red colors. This compact underwater LED light produces more light output than a 55 watt halogen, yet uses a fraction the amount of electrical current, which is a big plus for boat owners. Waterproof to 6 feet, this light is constructed of anodized aluminum and is approved for the harsh saltwater environment. This unit can be mounted to the hull above or below the waterline, while a small approximately 3/8 inch hole runs through the hull, allowing the unit to be wired from the other side. Three smaller screws secure the unit to the hull. This mounting method greatly reduces the size and or amount of holes that typically must be drilled in the hull for installation of traditional halogen underwater lights. Page: 1
Click Photo to Enlarge Click Photo to Enlarge Click Photo to Enlarge Click Photo to Enlarge Click Photo to Enlarge Click Photo to Enlarge 53" Container with White 53" Container with Amber 53" Container with Red Click Photo to Enlarge Click Photo to Enlarge Click Photo to Enlarge Page: 2
These units are fully sealed, weatherproof, and constructed of aluminum with stainless steel hardware for durability and corrosion resistance. Measuring only 4.25" in diameter and 1.25 in total thickness, these compact units are designed for surface mounting in either interior or exterior applications. The 800 lumen light output at approximately 12 watts @1 amp draw of these LED lights makes them ideal for applications where power management is critical such as boats and RV's. Waterproof to 60 meters for marine environments, these versatile LED lights can be installed above or below water. Each light is mounted via three screws and a 3/8 inch hole for wiring. The LEDs are housed within a hard anodized and powder coated aluminum chassis that provides excellent strength and durability. This unit can be operated with voltages ranging from 9 to 42 VDC and draws 950mA at 12 Volts DC and 475mA at 24 Volts DC. The entire unit measures only 3.9 inches in diameter by 1.25 inches thick, making it very low profile and easy to mount unobtrusively on the hull below the waterline. This light contains intelligent circuitry that controls voltage so there is no additional hardware or drive circuits needed to complete installation. This light comes with a ten inch pigtail wire with bare ends for hardwiring into electrical supplies. We have also been selling these for use as swimming pool lights. In many states, code dictates that pool lights should have a step down transformer. The 120 Volts or 240 Volts is stepped down to 12 volts DC to the line running to the pool lights. The pool light only pulls 12 volts DC, which is not harmful in water. Higher voltage pool lights running off of high voltage (120 Volts or 240 volts) are typically connected to a GFI, which will cut the power in the event that the current makes contact with the water. However, if the GFI fails due to outdoor exposure, the high voltage current combined with the pool water can be deadly. With this light, there is no risk of electrocution. Finally, because this light runs at much lower voltage and amperage, smaller wires are needed. Thus, much smaller holes are needed to mount this light to the pool's wall surface. Specifications / Additional Information LEDEUL4-10ST Underwater LED Light Lamp Type: LED Dimensions:.4.25"Diameter 1.25 " Depth Watts: 12 Voltage: 9-42 VDC Mounting: Surface Mount Wiring: 2 Wire - 10" stripped & tinned Amps: 1 (on 12 volts).5 (on 24 volts) Certification-Features Multiple Color Options Very low profile Durable Aluminum housing Low 1A draw Waterproof to 60 Meters Multi-Voltage High 800 Lumen Output Lumens: 800 LED Life Expectancy: 50,000+ hours Materials: Anodized Aluminum Housing Special Orders- Requirements Contact us for special requirements LED Life Expectancy: 50,000 hours Toll Free: 1-800-369-6671 Intl: 1-903-498-3363 E-mail: sales@larsonelectronics.com 3 year warranty replacement on this LED light. After 30 days, the customer ships the failed LED light and/or LED bulb to Larson Electronics at their expense. If the failure is a manufacturer defect, we will ship a new replacement to the customer. If failure occurs within 30 days of receipt, Larson Electronics will provide a return label via email to the customer. When the failed light is returned, Larson Electronics will ship a new replacement. NSN# 6210-01-647-7649 Scroll Down to Purchase- This product does not qualify for free shipping. Part #: LEDEUL4-10ST (48563) Page: 3
Page: 4
Options: LEDEUL4-10ST- BEAM COLOR - BEAM PATTERN Example: LEDEUL4-10ST-AMB-SP BEAM COLOR Amber -AMB Blue -BLU BEAM PATTERN Spot -SP Flood -FL White -WHT Red -RED Green -GRN Infrared850 -IR850 Infrared940 -IR940 UV 365 -UV365 UV 395 -UV395 Page: 5
Page: 6
Page: 7
Links (Click on the below items to view): - Dimensional Drawing - Manual Page: 8