V-7000 Series Selection Guide T V-7000 Series 1/2 to 2 Globe Vlves with Fort M400, M800, nd M1500 ctutors pplictions T Fort M400, M800, nd M1500 series liner ctutors mount directly 1 onto 1/2 to 2 V-7xxx series two-wy nd three-wy globe vlve bodies. pplictions include chilled or hot wter nd stem. Field selectble input signls include reverse nd direct cting, floting or proportionl 0-10 Vdc, 2-10 Vdc, or 4-20 mdc, nd proportionl sequencing input signl rnges 2. pplicble Literture T Fort M400 nd M800 Instlltion Instructions, DIM119E (F-27506) T Fort M1500 Instlltion Instructions, DIM121E (F-27507) V-811 Instlltion Instructions, F-27442 T Vlves ctlog, F-27414-28 ontrol Vlve Sizing, F-13755 Selection Guide ontents pplictions... pge 1 Vlve nd ctutor Selection Procedure... pge 2 T V-72xx Series Two-Wy Vlve odies... pge 3 T V-73xx Series Three-Wy Vlve odies... pge 4 T Fort ctutor Model hrt... pge 5 mbient Temperture Restrictions... pge 5 Vlve/ctutor lose-off Pressures... pge 5 Fctory Vlve nd ctutor ssemblies... pge 6 Fort ctutor Dimensions... pge 7 Two-Wy Vlve/ctutor ssembly Dimensions... pge 8 Three-Wy Vlve/ctutor ssembly Dimensions... pge 9 1. V-811 linkge dpter kit required (order seprtely). 2. 0-5 Vdc, 5-10 Vdc, 2-6 Vdc, nd 6-10 Vdc Printed in U.S.. 8/08 opyright 2008 T. ll rights reserved. F-27490-3
Vlve nd ctutor Selection Procedure 1. Determine the required flow coefficient (v/kvs). Using the required flow nd pressure drop for the ppliction (consult 28, F-13755 if necessry), determine the required flow coefficient. 2. Determine vlve body prt number. Select two-wy vlve body from Tble-1 or three-wy mixing or diverting vlve body from Tble-2 hving the required flow coefficient, size, body pttern, end connection, nd temperture/pressure rtings pproprite for the ppliction. 3. Select the Fort ctutor Using the required close-off pressure for the ppliction, consult Tble-5 nd select Fort ctutor hving sufficient close-off pressure on the vlve body selected in Step 2. dditionl Fort ctutor specifictions my be found in Tble-3 or in the Fort Instlltion Instructions sheets shown in pplicble Literture. 4. Determine ssembly Prt Number If complete vlve nd ctutor ssembly is required, consult Tble-3 for the ctutor code of the Fort ctutor selected in Step 3. For the complete ssembly prt number: hnge the vlve body prt number prefix from V to VU. Insert the ctutor code in the third field of the prt number. onfirm the vilbility of the fctory ssembly by consulting Tble-6 (two-wy vlves), Tble-7 (three-wy mixing vlves), or Tble-8 (three-wy diverting vlves). Exmple: Vlve body: V-7213-0-4-4 ctutor: M400 (ctutor code 674 from Tble-3) omplete ssembly: VU-7213-674-4-4 Fort ctutors re field configured for the desired control signl type nd rnge plus the desired ction. onsult the pproprite Fort Instlltion Instructions for further informtion (see pplicble Literture). 2 opyright 2008 T. ll rights reserved. F-27490-3
Vlve ody nd ctutor Selection Tble-1 T V-72xx Series Two-Wy Vlve odies Two-Wy Vlves Stem Up Open or Stem Up losed 1/2 to 1/1/4 Union ngle nd strightwy 5/8 OD SE Flred 1/2 to 2 Union Swet 1/2 to 2 NPT or Rp Threded Union ngle Union Strightwy ppliction: hilled or Hot Wter SE Flred Union Swet NPT Threded Rp Threded ppliction: Hot Wter or Stem NPT Threded Size 1/2 to 1-1/4 1/2 to 1-1/4 5/8 OD 1/2 to 2 1/2 to 2 15 to 50 mm 1/2 to 2 Vlve ody Prt Number, Stem Up Open V-7211-0-3-P V-7211-0-4-P V-7212-0-4-P V-7214-0-4-P V-7213-0-4-P V-7215-0-4-P V-7253-0-4-P V-7273-0-4-P Vlve ody Prt Number, Stem Up losed V-7221-0-4-P V-7222-0-4-P V-7224-0-4-P V-7223-0-4-P V-7225-0-4-P V-7263-0-4-P V-7283-0-4-P Flow Type Equl % Modified Liner ody ronze ronze Set ronze Stinless Steel Mteril Stem Stinless Steel Stinless Steel Plug rss Stinless Steel Pcking Spring Loded TFE/EPDM Spring Loded TFE Disc EPDM Teflon None Pressure lss NSI 250 Up to 400 F (204 ) below 150 F (65 ) ISO PN16 Mximum Inlet Pressure, Stem 35 PSIG (241 kp) 100 PSIG (690 kp) 150 PSIG (1034 kp) llowble ontrol Medi Temperture 20 F to 281 F (-7 to 138 ) 20 to 340 F (-7 to 171 ) 20 to 400 F (-7 to 205 llowble Differentil Pressure, Wter b 35 PSI (241 kp) for Norml Life 35 PSIG (241 kp) 35 PSIG (241 kp) llowble Differentil Pressure, Stem b 20 PSI (138 kp) 35 PSI (241 kp) 50 PSI (345 kp) To Select Port ode (P) P ode Vlve Size v (kvs) Rting 01 0.4 (0.34) 0.4 (0.34) 0.4 (0.34) 0.4 (0.34) 0.4 (0.34) 0.4 (0.34) 0.4 (0.34) 02 1/2 1.3 (1.1) 1.3 (1.1) 1.3 (1.1) 1.3 (1.1) 1.3 (1.1) 1.3 (1.1) 1.3 (1.1) 03 (15 mm) 2.2 (1.9) 2.2 (1.9) 2.2 (1.9) 2.2 (1.9) 2.2 (1.9) 2.2 (1.9) 2.2 (1.9) 04 5.0 (4.3) 4.4 (3.8) 4.4 (3.8) 4.4 (3.8) 4.4 (3.8) 4.4 (3.8) 4.4 (3.8) 05 5.5 (4.7) 5.5 (4.7) 5.5 (4.7) 5.5 (4.7) 5.5 (4.7) 5.5 (4.7) 3/4 (20 mm) 06 8.5 (7.4) 7.5 (6.5) 7.5 (6.5) 7.5 (6.5) 7.5 (6.5) 7.5 (6.5) 07 14 (12) 10 (8.6) 10 (8.6) 10 (8.6) 10 (8.6) 10 (8.6) 1 (25 mm) 08 16 (14) 14 (12) 14 (12) 14 (12) 14 (12) 14 (12) 09 1-1/4 (32 mm) 22 (19) 20 (17.3) 20 (17.3) 20 (17.3) 20 (17.3) 20 (17.3) 10 1-1/2 (40 mm) 28 (21.2) 28 (21.2) 28 (21.2) 28 (21.2) 11 2 (50 mm) 40 (34.6) 40 (34.6) 40 (34.6) 40 (34.6) 15 to 50 mm vlves with metric thred Rp 1/2 to Rp 2 b Mximum recommended differentil in full open position. Do not exceed recommended differentil pressure (pressure drop) or integrity of prts my be ffected. F-27490-3 opyright 2008 T. ll rights reserved. 3
Tble-2 T V-73xx Series Three-Wy Vlve odies Three-Wy Vlves ppliction: hilled or Hot Wter Mixing or Diverting 5/8 OD SE Flred 1/2 to 2 NPT or Rp Threded 1/2 to 2 Union Swet SE Flred NPT Threded Rp Threded Union Swet NPT Threded Size 5/8 OD 1/2 to 2 15 to 50 mm 1/2 to 2 1/2 to 2 Vlve ody Prt Number, Mixing V-7312-0-4-P V-7313-0-4-P V-7315-0-4-P b V-7314-0-4-P Vlve ody, Prt Number Diverting c V-7323-0-4-P Flow Type Equl % Mteril ody Set Stem Plug Pcking Disc ronze ronze Stinless Steel rss Spring Loded TFE/EPDM None Pressure lss NSI 250 Up to 400 F (204 ) below 150 F (65 ) ISO PN16 llowble ontrol Medi Temperture llowble Differentil Pressure, Wter d 20 F to 281 F (-7 to 138 ) 35 PSI (241 kp) for Norml Life To Select Port ode (P) P ode Vlve Size v (kvs) Rting 02 1/2 2.2 (1.9) 2.2 (1.9) 2.2 (1.9) 04 (15 mm) 4.4 (3.8) 4.4 (3.8) 4.4 (3.8) 4.4 (3.8) 06 7.5 (6.5) 7.5 (6.5) 7.5 (6.5) 1 (25 mm 08 14 (12) 14 (12) 15 (13) 09 1-1/4 (32 mm) 20 (17.3) 20 (17.3 20 (17.3) 10 1-1/2 (40 mm) 28 (21.2) 28 (21.2) 28 (21.2) 11 2 (50 mm) 41 (36) 40 (34.6) 40 (34.6) On V-7313 nd V-7315 mixing vlves, port is the common port (locted on the side) nd ports nd re inlets. Flow is from to when the vlve stem is in up position (port closed). Flow is from to when vlve stem is in down position (port closed). b 15 to 50 mm vlves with metric thred Rp 1/2 to Rp 2 c On V-7323 diverting vlves, inlet port is the common port (locted on the bottom) nd ports nd re outlets. When the vlve stem is in the up position, flow is from to (port closed). When the vlve stem is in the down position, flow is from port to (port closed). d Mximum recommended differentil in full open position. Do not exceed recommended differentil pressure (pressure drop) or integrity of prts my be ffected. 4 opyright 2008 T. ll rights reserved. F-27490-3
Tble-3 T Fort ctutor Model hrt Model ctutor ode Force, lbf (N) Power Running V Trnsformer Sizing V Floting ontrol Proportionl ontrol Feedbck (2) SPDT uxiliry Switches M400 c 674 M400-S2 c b 90 (400) 6 30 0-10 Vdc, M800 c 680 No 180 24 Vc ±10% 2-10 Vdc, 15 50 Yes 2-10 Vdc (800) 50/60 Hz or M800-S2 c b 4-20 mdc 24 Vc 4 M1500 c 686 No 337 15 50 (1500) M1500-S2 c b 24 Vc 4 DIP switch selectble. b No ctutor code. No fctory ssemblies offered. c V-811 linkge (order seprtely) required for mounting ctutors to V-7xxx globe vlve bodies. Do not use M1500 on V-7323 three-wy vlves. No 24 Vc 4 Tble-4 Restrictions on mbient Temperture for Fort Vlve ctutors Fluid Temperture in Vlve ody Mximum llowble mbient Temperture hilled Wter 122 F (50 ) 281 F (138 ) 113 F (45 ) 300 F (149 ) 107 F (42 ) 340 F (171 ) 100 F (38 ) Note: When instlling vlve nd ctutor ssemblies, observe the minimum nd mximum fluid nd mbient temperture limits shown in Tble-1, Tble-2, nd Tble-4. 366 F (186 ) 90 F (32 ) Minimum llowble mbient operting temperture 14 F (-10 ) Tble-5 Select Vlve/ctutor ombintion Hving Sufficient lose-off for ppliction Vlve ody lose-off Rtings, psi (kp) Two-Wy Vlves P ode Size M400 M800 M1500 V-7211-0-3-P V-7211-0-4-P V-7212-0-4-P V-7213-0-4-P V-7214-0-4-P V-7215-0-4-P V-7221-0-4-P V-7222-0-4-P V-7223-0-4-P V-7224-0-4-P V-7225-0-4-P V-7253-0-4-P V-7263-0-4-P V-7273-0-4-P V-7283-0-4-P -1, -2, -3, -4 1/2 (15 mm) 250 (1712) 250 (1712) -5, -6 3/4 (20 mm) 198 (1356) 250 (1712) -7, -8 1 (25 mm) 92 (630) 207 1418) -9 1-1/4 (32 mm) 56 (384) 130 (890) -10 1-1/2 (40 mm) 37 (253) 88 (603) 177 (1212) -11 2 (50 mm) 19 (130) 48 (329) 98 (671) Three-Wy Vlves P ode Size M400 M800 M1500 b -2, -4 1/2 (15 mm) 250 (1712) 250 (1712) -6 3/4 (20 mm) 198 (1356) 250 (1712) V-7312-0-4-P V-7313-0-4-P V-7314-0-4-P V-7315-0-4-P -8 1 (25 mm) 92 (630) 207 1418) -9 1-1/4 (32 mm 56 (384) 130 (890) 10 1-1/2 (40 mm) 37 (253) 88 (603) -11 2 (50 mm) 19 (130) 48 (329) V-7323-0-4-P -4, -6, -8, -9, -10, -11 1/2 to 2 250 (1712) Do Not Use b b V-811 linkge (order seprtely) required for mounting V-7xxx vlve bodies. Do not use M1500 on V-7323 three-wy vlves. F-27490-3 opyright 2008 T. ll rights reserved. 5
Fctory ssemblies Tble-6 Fctory Vlve nd ctutor ssemblies Two-Wy Vlves ctutor Model (ctutor ode b ) Vlve ssembly Prt Number b P ode b Size M400 (674) M800 (680) M1500 (686) 1, 2, 3, 4 1/2 X 5, 6 3/4 X X VU-7213-xxx-4-P VU-7253-xxx-4-P VU-7273-xxx-4-P 7, 8 1 X X 9 1-1/4 X X 10 1-1/2 X X X 11 2 X X X b See Tble-5 for close-off pressures Insert ctutor ode in third field of ssembly prt number. Insert P ode in lst field of ssembly prt number. Tble-7 Fctory Vlve nd ctutor ssemblies Three-Wy Mixing Vlves ctutor Model (ctutor ode b ) Vlve ssembly Prt Number b P ode b Size M400 (674) M800 (680) 2, 4 1/2 X 6 3/4 X VU-7313-xxx-4-P 8 1 X 9 1-1/4 X 10 1-1/2 X X 11 2 X X b See Tble-5 for close-off pressures Insert ctutor ode in third field of ssembly prt number. Insert P ode in lst field of ssembly prt number. Tble-8 Fctory Vlve nd ctutor ssemblies Diverting Vlves ctutor Model (ctutor ode b ) Vlve ssembly Prt Number b P ode b Size M400 (674) 4 1/2 X 6 3/4 X VU-7323-xxx-4-P 8 1 X 9 1-1/4 X 10 1-1/2 X 11 2 X b See Tble-5 for close-off pressures Insert ctutor ode in third field of ssembly prt number. Insert P ode in lst field of ssembly prt number. 6 opyright 2008 T. ll rights reserved. F-27490-3
Dimensions 3-1/4" (82 mm) 4-19/32" (117 mm) 9-17/32 (242 mm) 6-5/16" (173 mm) 12-13/32" (315 mm) llow 3 (76 mm) min. clernce for cover removl D Figure-1 Fort ctutor Dimensions V-7211-0-3-P Union ngle V-7213-0-4-P NPT Threded V-7215-0-4-P Rp Threded V-7253-0-4-P NPT Threded V-7273-0-4-P NPT Threded V-7222-0-4-P SE Flred V-7211-0-4-P Union Strightwy V-7214-0-4-P Union Swet V-7223-0-4-P NPT Threded V-7225-0-4-P Rp Threded V-7263-0-4-P NPT Threded V-7283-0-4-P NPT Threded V-7212-0-4-P 5/8 OD SE Flred V-7221-0-4-P Union Strightwy V-7224-0-4-P Union Swet Figure-2 Two Wy V-7xxx Vlve ody Dimensions F-27490-3 opyright 2008 T. ll rights reserved. 7
Tble-9 Dimensions Two-Wy Vlves (see Figure-1 nd Figure-2) Vlve ody Prt Number Size Dimensions in Inches (mm) D 1/2 3-1/8 (79) 1-5/8 (41) 3/4 (19) 10-9/32 (261) V-7211-0-3-P 3/4 3-5/8 (92) 1-11/16 (43) 15/16 (24) 10-15/32 (266) 1 4-1/16 (103) 1-15/16 (49) 1-1/4 (32) 10-25/32 (274) 1-1/4 4-5/16 (110) 2-3/16 (56) 1-11/16 (43) 11-7/32 (285) 1/2 ' 4-3/16 (106) 1-1/16 (27) 1-1/8 (29) 10-21/32 (271) V-7211-0-4-P 3/4 4-15/16 (125) 1-1/16 (27) 1-1/8 (29) 10-21/32 (271) 1 6 (152) 1-1/8 (29) 1-3/16 (30) 10-23/32 (272) 1-1/4 6-1/4 (159) 1-3/8 (35) 1-7/16 (37) 10-31/32 (279) V-7212-0-4-P 5/8 O.D. 4 (102) 1-1/16 (27) 1-1/8 (29) 10-21/32 (271) 1/2 (15 mm) 3 (76) 1-1/16 (27) 1-1/8 (29) 10-21/32 (271) 3/4 (20 mm) 3-5/8 (92) 1-1/16 (27) 1-1/8 (29) 10-21/32 (271) V-7213-0-4-P V-7215-0-4-P V-7253-0-4-P V-7273-0-4-P 1 (25 mm) 4-5/8 (117) 1-1/8 (29) 1-3/16 (30) 10-23/32 (272) 1-1/4 (32 mm) 4-5/8 (117) 1-3/8 (35) 1-7/16 (37) 10-31/32 (279) 1-1/2 (40 mm) 5-3/8 (137) 1-1/2 (38) 1-7/8 (48) 11-13/32 (290) 2 (50 mm) 6-1/8 (156) 1-9/16 (40) 2-1/854) 11-21/32 (296) 1/2 4-3/16 (106) 1-1/16 (27) 1-1/8 (29) 10-21/32 (271) 3/4 5-7/16 (138) 1-1/16 (27) 1-1/8 (29) 10-21/32 (271) V-7214-0-4-P 1 6-5/8 (168) 1-1/8 (29) 1-3/16 (30) 10-23/32 (272) 1-1/4 6-13/16 (173) 1-3/8 (35) 1-7/16 (37) 10-31/32 (279) 1-1/2 8-5/16 (211) 1-1/2 (38) 1-7/8 (48) 11-13/32 (290) 2 9-3/16 (233) 1-9/16 (40) 2-1/854) 11-21/32 (296) 1/2 4-3/16 (106) 1-1/4 (32) 1-1/8 (29) 10-21/32 (271) V-7221-0-4-P 3/4" 4-15/16 (125) 1-1/4 (32) 1-1/8 (29) 10-21/32 (271) 1" 6 (152) 1-3/4 (45) 1-3/16 (30) 10-23/32 (272) 1-1/4" 6-1/4 (159) 1-3/4 (45) 1-7/16 (37) 10-31/32 (279) V-7222-0-4-P 5/8 OD 4 (102) 1-1/4 (32) 1-1/8 (29) 10-21/32 (271) 1/2 (15 mm) 3-1/16 (78) 1-3/16 (30) 1-1/8 (29) 10-21/32 (271) 3/4 (20 mm) 3-5/8 (92) 1-3/16 (30) 1-1/8 (29) 10-21/32 (271) V-7223-0-4-P V-7225-0-4-P V-7263-0-4-P V-7283-0-4-P 1 (25 mm) 4-5/8 (117) 1-3/4 (44) 1-3/16 (30) 10-23/32 (272) 1-1/4 (32 mm) 4-5/8 (117) 1-3/4 (44) 1-7/16 (37) 10-31/32 (279) 1-1/2 (40 mm) 5-3/8 (137) 1-13/16 (46) 1-9/16 (40) 11-3/32(282) 2 (50 mm) 6-1/8 (156) 2-1/4 (57) 1-5/8 (42) 11-5/32 (283) 1/2 4-3/16 (106) 1-1/4 (32) 1-1/8 (29) 10-21/32 (271) 3/4" 5-7/16 (138) 1-1/4 (32) 1-1/8 (29) 10-21/32 (271) V-7224-0-4-P 1" 6-5/8 (168) 1-3/4 (45) 1-3/16 (30) 10-23/32 (272) 1-1/4" 6-13/16 (173) 1-3/4 (45) 1-7/16 (37) 10-31/32 (279) 1-1/2" 8-5/16 (211) 1-13/16 (45) 1-9/16 (40) 11-3/32(282) 2" 9-3/16 (233) 2-1/16 (53) 1-5/8 (42) 11-5/32 (283) ssembly height, centerline of vlve body to top of ctutor (see Figure-1). Leve n dditionl 3 (76 mm) clernce for cover removl. 8 opyright 2008 T. ll rights reserved. F-27490-3
V-7312-0-4-P SE Flred V-7313-0-4-P NPT Threded V-7315-0-4-P Rp Threded V-7323-0-4-P NPT Threded V-7314-0-4-P Union Swet Figure-3 Three-Wy V-73xx Vlve ody Dimensions Tble-10 Dimensions Three-Wy Vlves (see Figure-1 nd Figure-3) Vlve ody Prt Number Size Dimensions in Inches (mm) D V-7312-0-4-P 5/8 OD 4 (102 2-1/4 (57) 1-1/8 (29) 10-21/32 (271) 1/2 (15 mm) 3-1/16 (76) 1-3/4 (44) 1-1/8 (29) 10-21/32 (271) 3/4 " (20 mm) 3-5/8 (92) 1-13/16 (46) 1-1/8 (29) 10-21/32 (271) V-7313-0-4-P V-7315-0-4-P 1" (25 mm) 4-5/8 (118) 1-3/4 (44) 1-3/16 (30) 10-23/32 (272) 1-1/4" (32 mm) 4-5/8 (118) 1-3/4 (44) 1-7/16 (37) 10-31/32 (279) 1-1/2" (40 mm) 5-3/8 (137) 1-13/16 (46) 1-9/16 (40) 11-3/32(282) 2" (50 mm) 6-1/8 (156) 2-1/4 (57) 1-5/8 (42) 11-5/32 (283) 1/2" 4-3/16 (106) 2-5/16 (59) 1-1/8 (29) 10-21/32 (271) 3/4" 5-7/16 (138) 2-5/8 (67) 1-1/8 (29) 10-21/32 (271) V-7314-0-4-P 1" 6-5/8 (168) 3-3/16 (81) 1-3/16 (30) 10-23/32 (272) 1-1/4" 6-13/16 (173) 3-7/16 (87) 1-7/16 (37) 10-31/32 (279) 1-1/2" 8-5/16 (211) 3-3/4 (95) 1-9/16 (40) 11-3/32(282) 2" 9-3/16 (233) 4-3/16 (106) 1-5/8 (42) 11-5/32 (283) 1/2" 3-1/16 (76) 1-3/8 (35) 1-1/8 (29) 10-21/32 (271) 3/4" 3-5/8 (92) 1-11/16 (43) 1-1/8 (29) 10-21/32 (271) V-7323-0-4-P 1" 4-5/8 (118) 1-9/16 (40) 1-3/16 (30) 10-23/32 (272) 1-1/4" 4-5/8 (118) 1-5/8 (41) 1-7/16 (37) 10-31/32 (279) 1-1/2" 5-3/8 (137) 1-11/16 (43) 1-9/16 (40) 11-3/32(282) 2" 6-1/8 (156) 1-7/8 (48) 1-5/8 (42) 11-5/32 (283) ssembly height, centerline of vlve body to top of ctutor (see Figure-1). Leve n dditionl 3 (76 mm) clernce for cover removl. F-27490-3 opyright 2008 T. ll rights reserved. 9
Selection Guide V-8000 Series V-9313 Series T V-8000 Series nd V-9000 Series 2-1/2 to 6 Globe Vlves with T Fort M800 nd M1500 ctutors pplictions T Fort M800, nd M1500 series liner ctutors mount directly onto 2-1/2 to 6 V-8xxx series nd V-9313 series two-wy nd three-wy globe flnged vlve bodies. pplictions include chilled or hot wter nd stem. Field selectble input signls include reverse nd direct cting, floting or proportionl 0-10 Vdc, 2-10 Vdc or 4-20 m, nd proportionl sequencing input signl rnges. pplicble Literture T Fort M400 nd M800 Instlltion Instructions, DIM119 (F-27506) T Fort M1500 Instlltion Instructions, DIM121 (F-27507) V-812 Instlltion Instructions, F-27443 T Vlves ctlog, F-27414-28 ontrol Vlve Sizing, F-13755 Selection Guide ontents pplictions............................... pge 1 Vlve nd ctutor Selection Procedure......... pge 1 T V-8000 Series Vlve odies............. pge 2 T V-9000 Series Vlve odies............. pge 3 Vlve/ctutor lose-off Pressures............. pge 4 T Fort ctutor Model hrt............... pge 4 mbient Temperture Restrictions.............. pge 4 lose-off Pressure nd V-8xxx Mximum Operting Pressure Differentil......................... pge 4 Fctory Vlve nd ctutor ssemblies.......... pge 5 V-8xxx nd V-9313 Vlve ody ction........ pge 5 Fort ctutor nd Vlve ody Dimensions....... pge 6 V-8xxx Dimensions......................... pge 7 V-9313 Dimensions........................ Pge 7 Vlve nd ctutor Selection Procedure 1. Determine the required flow coefficient (v/kvs). Using the required flow nd pressure drop for the ppliction, determine the required flow coefficient (consult 28, F-13755 if necessry). 2. Determine vlve body prt number. Select flnged V-8xxx vlve body from Tble-1 or flnged V-9313 vlve body from Tble-2 hving the required flow coefficient, size, body pttern, end connection, nd temperture/pressure rtings pproprite for the ppliction. 3. Select the Fort ctutor Using the required close-off pressure for the ppliction, consult Tble-5 nd select Fort ctutor hving sufficient close-off pressure on the vlve body selected in step 2. For vlve/ctutor combintions using V-8xxx vlve bodies, lso consult Tble-5 for mximum operting pressure differentil limittions. dditionl Fort ctutor specifictions my be found in Tble-3 or in the Fort Instlltion Instructions sheets shown in pplicble Literture. If necessry, use the dimensionl informtion in Figure-1, Figure-2, Tble-8, nd Tble-9 to confirm tht the vlve-ctutor ssembly will fit in the vilble spce. 4. Determine ssembly Prt Number If complete fctory vlve nd ctutor ssembly is required, consult Tble-3 for the ctutor code of the Fort ctutor selected in Step 3. For the complete ssembly prt number: hnge the vlve body prt number prefix from V to VU. Insert the ctutor code in the third field of the prt number. onfirm the fctory ssembly is vilble in Tble-6 Exmple: Vlve body: V-8213-0-4-14 ctutor: M1500 (ctutor code 686 from Tble-3) omplete ssembly: VU-8213-686-4-14 Fort ctutors re field configured for the desired control signl type nd rnge plus the desired ction. onsult the pproprite Fort Instlltion Instructions for further informtion (see pplicble Literture). Printed in U.S.. 8/08 opyright 2008 T. ll rights reserved. F-27491-2
Vlve ody nd ctutor Selection Tble-1 T V-8213, V-8223, nd V-8303 Vlve odies ppliction hilled or Hot Wter, Stem Two-Wy Flnged hilled or Hot Wter Three-Wy Flnged Two-Wy nd Three-Wy Vlves Two-wy Stem Up Open or Stem Up losed Three-wy Mixing/Diverting S 125 Flnged st Iron ody Size 2-1/2 to 6 2-1/2 to 6 2-1/2 to 6 Vlve ody Prt Number V-8213-0-5-P V-8223-0-5-P V-8303-0-5-P Vlve ody ction 2-Wy Stem Open 2-Wy Stem Up losed 3-Wy Mixing/Diverting Linkge Kit Prt Number V-812 b Flow Type Equl % Equl % Modifier Liner ody st Iron st Iron st Iron Set Forged rss Forged rss Forged rss Mteril Stem Stinless Steel Stinless Steel Stinless Steel Plug Forged rss Forged rss Forged rss Pcking Spring Loded TFE/EPDM Spring Loded TFE/EPDM Spring Loded TFE/EPDM Set Ring EPDM EPDM None NSI Pressure lss, psig 125 Mximum Inlet Pressure Stem psig (kp) 35 psig (241 kp) llowble ontrol Medi 20 F to 281 F Temperture, F ( ) c ( 7 to 138 ) lose-off Pressure, psi (kp) 125 psi (856 kp) d 35 psi (241 kp) d P ode Vlve Size, In. v (k vs ) v (k vs ) v (k vs ) Mixing e Diverting f 12 2-1/2 56 (48) 56 (48) 80 (69) 95 (82) g 115 (99) h 13 3 85 (74) 85 (74) 110 (95) 120 (104) i 14 4 145 (125) 145 (125) 190 (164) 190 (164) i 15 5 240 (208) 240 (208) 290 (251) 290 (251) i 16 6 370 (320) 370 (320) 500 (433) 500 (433) i V-8303 vlves my be used s either mixing or diverting vlves. V-8303 vlves will lso operte stisfctorily s two-wy ngle vlves if either end (side) port is closed off. b V-812 linkge kit included with M1500 ctutor. Purchse seprtely for M800 ctutors. c UTION: Freeze protection required for tempertures below 32 F (0 ). void ice formtion on stems. d Vlve in closed position. See Tble-5 for mximum llowble V-8xxx differentil pressure for vlve in ny open position. e Mixing configurtion, ports nd re inlets, port is outlet. Port locted on bottom. f Diverting configurtion, port is inlet, ports nd re outlets. Port locted on bottom. g Diverting configurtion, flow to ports. h Diverting configurtion, flow to ports. i ll diverting flow configurtions, flow to either or ports. 2 opyright 2008 T. ll rights reserved. F-27491-2
Tble-2 T V-9313 Vlve odies ppliction hilled or Hot Wter Three-Wy Vlves Three-wy mixing NSI 125 Flnged st Iron ody S Flnged Size 2-1/2 to 6 Vlve ody Prt Number Linkge Kit Prt Number V-9313-0-5-P V-812 Flow Type Mixing b ody st Iron Set st Iron Mteril Stem Stinless Steel Plug rss Pcking Spring Loded TFE/EPDM Disc None NSI Pressure lss, psig 125 llowble ontrol Medi Temperture, F ( ) c 40 F to 281 F (4 to 138 ) llowble Differentil Pressure, Wter, psi (kp) d 35 psi (241 kp) P ode Vlve Size, In. v (k vs ) Rting 12 2-1/2 67 (58) 13 3 91 (79) 14 4 170 (147) 15 5 290 (251) 15 6 390 (337) b c d V-812 linkge kit included with M1500 ctutor. Purchse seprtely for M800 ctutors. Port is the common port, ports nd re inlets. Flow is from to when vlve stem is in up position (port closed). Flow is from port to when vlve stem is down (port closed). ommon port is on the side. UTION: Freeze protection required for tempertures below 32 F (0 ). void ice formtion on stems. Mximum recommended differentil in full open position. Do not exceed recommended differentil pressure (pressure drop) or integrity of prts my be ffected. F-27491-2 opyright 2008 T. ll rights reserved. 3
Tble-3 T Fort ctutor Model hrt Model ctutor ode Force, lbf (N) Power Running V Trnsformer Sizing V Floting ontrol Proportionl ontrol Feedbck (2) SPDT uxiliry Switches Linkge M800 680 No 180 15 50 (800) 0-10 Vdc, M800-S2 b 24 Vc ±10% 24 Vc 4 2-10 Vdc, Yes 2-10 Vdc 50/60 Hz or M1500 686 337 4-20 mdc No 15 50 (1500) M1500-S2 b 24 Vc 4 V-812 (purchse seprtely) b DIP switch selectble No ctutor code. No fctory ssemblies offered. Tble-4 mbient Temperture Restrictions for Fort Vlve ctutors Fluid Temperture in Vlve ody hilled Wter Mximum llowble mbient Temperture 122 F (50 ) 281 F (138 ) 113 F (45 ) 300 F (149 ) 107 F (42 ) 340 F (171 ) 100 F (38 ) 366 F (186 ) 90 F (32 ) Minimum llowble mbient operting temperture 14 F (-10 ) Note: When instlling vlve nd ctutor ssemblies, observe the minimum nd mximum fluid nd mbient temperture limits shown in Tble-1, Tble-2, nd Tble-4. 4 opyright 2008 T. ll rights reserved. F-27491-2
Tble-5 Select Vlve/ctutor ombintion Hving Sufficient lose-off for ppliction lose-off Rtings, psi (kp) Mximum Operting Pressure Differentil, psi (kp) Vlve ody P ode Size M800 M800-S2 M1500 M1500-S2 M1500 M1500-S2 V-8213-0-5-P 125 (856) V-8223-0-5-P -12, -13, -14, 2-1/2 to 6 Do Not Use -15, -16 b V-8303-0-5-P 35 (241) 35 (241) c V-9313-0-5-P -12 2-1/2 29 (199) 61 (418) -13 3 19 (130) 42 (288) -14 4 10 (68) 22 (151) -15 5 14 (96) -16 6 9 (62) Note: Do not use M400 or M400-S2 ctutors on 2-1/2 to 6 V-8xxx or V-9313 vlve bodies. V-812 linkge dpter kit required for mounting (order seprtely). b M800 nd M800-S2 ctutors re not comptible with V-8xxx vlve bodies. c Mximum differentil in ny open position. For proper V-8xxx vlve opertion, do not exceed Mximum Operting Pressure Differentil. Fctory ssemblies Tble-6 Fctory Vlve nd ctutor ssemblies V-8000 Series Vlve ssembly Prt Number P ode Size ctutor Model (ctutor ode b ) M1500 (686) V-9313 Series Vlve ssembly Prt Number P ode Size ctutor Model (ctutor ode b ) M800 (680) M1500 (686) 12 2-1/2 X 12 2-1/2 X X VU-8213-xxx-5-P VU-8303-xxx-5-P 13 3 X 13 3 X X 14 4 X VU-9313-xxx-5-P 14 4 X X 15 5 X 15 5 X 16 6 X 16 6 X b Insert P code in lst field of ssembly prt number. Insert ctutor code in third field of ssembly prt number. Tble-7 V-8xxx nd V-9313 Vlve ody ction Vlve ody/ Vlve ssembly Vlve ody Description Stem Up Position ction (s ctutor strokes nd vlve stem goes down) V-8213-0-5-P VU-8213-xxx-5-P Two-Wy Stem up open Vlve open to flow decreses V-8223-0-5-P Two-wy stem up closed Vlve closed to flow increses V-8303-0-5-P VU-8303-xxx-5-P Three-wy mixing Three-wy diverting Flow to Flow to to flow decreses to flow increses (common port bottom) to flow decreses to flow increses (common port bottom) V-9313-0-5-P VU-9313-xxx-5-P Three-wy mixing Flow to to flow decreses to flow increses (common port side) F-27491-2 opyright 2008 T. ll rights reserved. 5
Dimensions 4-19/32" (117 mm) 6-5/16" (173 mm) llow 3 (76 mm) min. clernce for cover removl 3-1/4" (82 mm) 9-17/32 (242 mm) 12-13/32" (315 mm) D Figure-1 Fort ctutor Dimensions 1/2" - 20 Threds 1/2" - 20 Threds 1/2" - 20 Threds 1-1/4" - 16 Threds 1-1/4" - 16 Threds 1-1/4" - 16 Threds V-8213-0-5-P V-9223-0-5-P See Tble-X for Flnge Detil V-8223-0-5-P V-9213-0-5-P V-8303-0-5-P V-9313-0-5-P Flnge Dimensions H J Nominl Pipe Size Flnge Dimeter E Flnges Drilling olting Flnge Thickness F Dimeter of olt ircle G Dimeter of olt Holes H Number of olts Dimeter of olts Length of Mchine olts J G E E F 2-1/2 3 4 5 6 7 7-1/2 9 10 11 11/16 3/4 15/16 15/16 1 5-1/2 6 7-1/2 8-1/2 9-1/2 3/4 7/8 4 8 5/8 3/4 2-1/2 3 3-1/4 Figure-2 V-8xxx nd V-9xxx Vlve ody nd Flnge Dimensions 6 opyright 2008 T. ll rights reserved. F-27491-2
Tble-8 V-8xxx Dimensions (see Figure-1 nd Figure-2) Vlve ody Prt Number Size, Inches Dimensions in Inches (mm) D b 2-1/2 8-9/16 (217) 4 (102) 3-3/8 (86) 9-17/32 (242) 3 9-1/2 (241) 4-5/8 (117) 3-3/4 (95) 9-17/32 (242) V-8213-0-5-P 4 11-1/2 (292) 5-1/2 (140) 4-1/2 (114) 9-17/32 (242) 5 13 (330) 6-15/16 (176) 5-13/16 (148) 9-17/32 (242) 6 14 (356) 7-1/2 (191) 9-3/16 (233) 9-17/32 (242) 2-1/2 8-9/16 (217) 4 (102) 3-11/16 (94) 9-17/32 (242) 3 9-1/2 (241) 4-1/4 (108) 4-1/16 (103) 9-17/32 (242) V-8223-0-5-P 4 11-1/2 (292) 4-15/16 (125) 5-5/16 (135) 9-17/32 (242) 5 13 (330) 5-7/16 (138) 6-11/16 (170) 9-17/32 (242) 6 14 (356) 6-1/4 (159) 10-3/8 (264) 9-17/32 (242) 2-1/2 8-9/16 (217) 5-7/16 (138) 3-1/16 (78) 9-17/32 (242) 3 9-1/2 (241) 6-3/8 (162) 3-11/16 (94) 9-17/32 (242) V-8303-0-5-P 4 11-1/2 (292) 8-7/16 (214) 4-5/16 (110) 9-17/32 (242) 5 13 (330) 8-13/16 (224) 5-5/8 (143) 9-17/32 (242) 6 14 (356) 9-3/4 (248) 9 (229) 9-17/32 (242) See Figure-2 for flnge dimensions b ssembly height, centerline of vlve body to top of ctutor (see Figure-1). Leve n dditionl 3 (76 mm) clernce for cover removl. Tble-9 V-9313 Dimensions (see Figure-1 nd Figure-2) Vlve ody Prt Number Size, Inches Dimensions in Inches (mm) D b 2-1/2 8-9/16 (217) 5-3/8 (137) 3-1/2 (89) 9-17/32 (242) 3 9-1/2 (241) 6-3/8 (162) 3-3/4 (95) 9-17/32 (242) V-9313-0-5-P 4 11-1/2 (292) 8-1/2 (216) 4-1/2 (114) 9-17/32 (242) 5 13 (330) 8-3/4 (222) 5 (127) 9-17/32 (242) 6 14 (356) 9-3/4 (248) 5-7/8 (149) 9-17/32 (242) See Figure-2 fo flnge dimensions. b ssembly height, centerline of vlve body to top of ctutor (see Figure-1). Leve n dditionl 3 (76 mm) clernce for cover removl. F-27491-2 opyright 2008 T. ll rights reserved. 7
opyright 2008, T ll brnd nmes, trdemrks nd registered trdemrks re the property of their respective owners. Informtion contined within this document is subject to chnge without notice. F-27491-2 T 1354 lifford venue P.O. ox 2940 Loves Prk, IL 61132-2940 www.tc.com