T 340-1 / T 340-1 XL 40 USt Liing Capacity Truck Crane Datasheet Imperial T 340-1 T 340-1 XL Features: T 340-1 40 USt maximum liing capacity 94 maximum boom length 99 maximum tip height Engine power 0 hp Travel speeds up to 60 mph Features: T 340-1 XL 40 USt maximum liing capacity 5 maximum boom length 1 maximum tip height Engine power 0 hp Travel speeds up to 60 mph
CONTENTS T 340-1 / T 340-1 XL Page: Key...3 Dimensions Crane dimensions... 4, 5 Crane weights....6 Range diagram....7 Load charts, T 340-1 Main boom, outriggers fully extended (0%)....8 Main boom, outriggers fully fully retracted (0%)....8 Main boom, 32 offsettable jib....9 Main boom, 49 offsettable jib....9 Main boom, on tires....9 Load charts, T 340-1 XL Main boom, outriggers fully extended (0%).... Main boom, outriggers fully fully retracted (0%).... Main boom, 32 offsettable jib....11 Main boom, 49 offsettable jib....11 Main boom, on tires....11 Technical description Boom.... Hoist, rope, and hook...., 13 Cab, controls, operator aids and load limiter / load indicator....13 Superstructure....14 Counterweight....14 Tires....14 Vehicle performance....14 Hydraulic system....14 Carrier, engine, and drive-line.... 2
KEY T 340-1 / T 340-1 XL Boom length General performance Tip height Hoist speed Boom with extension Rope Standard / Optional Telescoping mode Rope diameter Boom angle Rope length Working radius Max. line pull Max. boom length with extension Electrical system Main boom with aux head Tires Hook and block Engine Hook and ball Steering Gradeability Speed Crane / Crane in standard configuration Slewing / Allowable slewing range Gross vehicle weight Slewing brake Weight on front axle Main hoist Weight on rear axle Auxiliary hoist Counterweight Cab Outriggers Operator aids / Load limiter / Load indicator Swing/Rotation Transmission Over rear Hydraulics 3
CRANE DIMENSIONS T 340-1 / T 340-1 XL T 340-1 Boom 0% 94' 0% 26'-4" T 340-1 XL Boom 0% 5' 0% 29'-9.5" 6" 9' Travel '-8.5" Low '-1" 7'-2.5" '-9" 26 14.5 T 340-1 2'-5" 2'-2" 2'-2" T 340-1 XL 5'-" ' 8' 17'-8" 9'-2" 33'-1" 4
CRANE DIMENSIONS T 340-1 / T 340-1 XL GROUND LINE Front " Rear 8" DRIVING WIDTH 8' OUTRIGGERS 0% ' Pinned 13'-8" 0% 7'-4-5" 0% 22' Pinned '-8" 0% 9'-4-5" 5
SPECIFICATIONS Approximate Crane Weights T 340-1 / T 340-1 XL Boom in front travel position Gross Vehicle Front max. Rear max. 22,000 45,000 Configurations: T 340-1 47,1 16,575,525 1/4 tank fuel 0 operator seated in cab Front tires: 425/65 R22.5-PR Rear tires: 11R22-14PR 94 boom/no jib 2,000 total counterweight T 340-1XL 60,053 16,5 43,528 1/4 tank fuel 0 operator seated in cab Front tires: 425/65 R22.5-PR Rear tires: 11R22-14PR 5 boom/no jib 11,000 total counterweight Add options Full tank of fuel + 3 + 1 + 195 Heater/defroster in upper cab + 60 5 + 65 Auxiliary hoist with drum roller and wire rope + 175 73 + 248 Electric remote control + 0 + 0 + 0 32 swing-on jib - 94 boom + 1,368 + 797 + 571 32 swing-on jib - 5 boom + 1,368 + 1,117 + 251 32 to 49 extendable swing-on jib - 94 boom + 1,789 + 1,007 + 785 32 to 49 extendable swing-on jib - 5 boom + 1,789 + 1,343 + 446 Auxiliary boom head - 94 boom + 0 + 4 54 Auxiliary boom head - 5 boom + 0 + 170 70 40 USt hook block on bumper + 690 + 973 283 7 USt hook and ball at bottom rack + 240 + 145 + 95 Substitute options 7,0 counterweight with 1,850 front bumper counterweight - 94 boom + 6,636 619 + 7,255 Spin resistant wire rope (per winch) + 32 + 44 6
RANGE DIAGRAM - MAIN BOOM Outriggers Fully Extended (0%) T 340-1 / T 340-1 XL 170 160 143 75 70 0 140 6 60 1 50 1 1 94 40 0 83 90 72 80 61 70 50 60 39 50 40 0 40 50 60 70 80 90 0 1 1 1 140 7
LOAD CHART - MAIN BOOM Outriggers Fully Extended (0%) T 340-1 7,0 s 0% 360º 94 Standard ASME B.5 Boom Length () 9 25 35 40 45 50 55 60 65 70 75 80 85 39 50 61 72 83 94 80,000 70,000 60,900 49,0 35,0 26,600 46,500 46,500 46,500 36,000 27,500 19,800 46,500 44,0 36,500 28,000,0,0 11,700 9,0 38,000 32,900 27,800,600,500,0 9,600 7,700 6,0 27,0 23,000 19,800,700,0 9,800 7,900 6,500 5,0 4,400 21,700 18,0,800,400 9,900 8,0 6,600 5,500 4,500 3,700 3,0 17,400 14,900 13,000 11,400,000 8,0 6,700 5,600 4,600 3,900 3,0 2,0 9 25 35 40 45 50 55 60 65 70 75 80 85 Outriggers Fully Retracted (0%) 7,0 s 0% 360º 94 Standard ASME B.5 Boom Length () 9 25 35 39 50 61 72 83 94 35,0 28,600,400 13,500 7,400 4,000 29,0 21,000 14,0 8,0 4,900 2,800 21,500 14,500 8,500 5,400 3,400 2,000 14,700 8,800 5,600 3,600 2,0 8,900 5,800 3,800 2,500 5,900 3,900 6,000 4,000 9 25 35 Notes to liing capacity Liing capacities do not exceed 85% of tipping load. Weight of hook blocks and slings is part of the load, and is to be deducted from the capacity ratings. Consult operation manual for further details. Note: Data published herein is intended as a guide only and shall not be construed to warrant applicability for liing purposes. Crane operation is subject to the computer charts and operation manual both supplied with the crane. 8
LOAD CHART - MAIN BOOM With Offset Jibs T 340-1 7,0 s 0% 360º Standard ASME B.5 0 Offset 32 Offsettable Jib Offset Offset 38 42 45 50 56 61 66 73 79 86 92 0 6 9,000 8,500 8,0 7,0 6,0 4,900 4,000 3,400 2,800 2,0 1,800 1,0 800 46 49 52 58 63 68 73 79 85 91 97 3 9 7,600 7,0 6,900 6,0 5,400 4,600 3,900 3,0 2,500 2,000 1,600 1,0 800 52 55 58 63 68 73 77 83 88 94 99 5 1 5,800 5,700 5,500 5,000 4,500 4,0 3,700 3,000 2,400 2,000 1,600 1,0 800 0 Offset 49 Offsettable Jib Offset Offset 41 47 52 60 66 71 77 84 91 0 9 116 2 5,000 4,700 4,400 4,000 3,700 3,500 3,0 2,900 2,0 1,800 1,400 900 600 55 59 64 70 76 81 86 93 99 6 1 119 6 3,0 3,0 3,0 2,900 2,800 2,700 2,0 1,900 1,500 1,0 900 500 62 68 73 79 84 88 93 99 5 1 116 2 7 2,500 2,400 2,400 2,0 2,0 2,0 1,900 1,500 1,0 900 500 On Tires On tires 7,0 s 29.5 X 25-28PR Over Rear Standard ASME B.5 Boom Travel Speed: Boom straight over rear 0 mph Creep 2.5 mph 19,0 19,0 19,0,800,800,800 39,0,0,0 39 7,600 7,600 7,600 25 50 5,0 5,0 5,0 50 3,600 3,600 3,600 35 50 40 50 1,700 1,700 1,700 Notes to liing capacity Liing capacities do not exceed 85% of tipping load, (75% of tipping load on tires). Weight of hook blocks and slings is part of the load, and is to be deducted from the capacity ratings. Consult operation manual for further details. Note: Data published herein is intended as a guide only and shall not be construed to warrant applicability for liing purposes. Crane operation is subject to the computer charts and operation manual both supplied with the crane. 9
11,000 s 08/22/17 T340-1/T340-1 XL, Round - Post release updates on pg _Approved 08/23/17 LOAD CHART - MAIN BOOM Outriggers Fully Extended (0%) T 340-1 XL 11,000 s 0% 360º 33.75 5 Standard ASME B.5 Boom Length () 9 25 35 40 45 50 55 60 65 70 75 80 85 90 95 0 33.75 45 57 69 81 93 5 80,000 64,400 58,000 50,700 38,400 28,600 46,500 46,500 46,500 38,800 29,600 22,500 16,800,700 46,500 44,500 36,400,0 23,0 17,0 13,400,700 8,500 41,600 34,800 29,400 23,400 17,600 13,700 11,000 8,900 7,0 5,900,600 26,000 22,500 17,800 13,900 11,0 9,0 7,500 6,0 5,0 4,0 3,400 23,400,0 17,700 14,0 11,0 9,0 7,600 6,0 5,0 4,0 3,600 2,900 2,0 18,600 16,0 14,0 11,400 9,0 7,700 6,400 5,0 4,400 3,700 3,000 2,500 2,000 1,500 1,0 9 25 35 40 45 50 55 60 65 70 75 80 85 90 95 0 Outriggers Fully Retracted (0%) 11,000 s 0% 360º 33.75 5 Standard ASME B.5 Boom Length () 25 35 40 45 33.75 45 57 69 81 93 5 37,0 26,800 27,0 18,0 18,500 18,800,600 11,000 11,0 11,400 6,500 7,000 7,0 7,400 7,600 3,900 4,500 4,800 4,900 5,0 2,0 2,700 3,000 3,0 3,400 700 1,400 1,800 2,000 2,0 1,000 1,0 36,400 26,000 17,0 9,600 5,500 5,0 3,500 2,0 1,0 25 35 40 45 Notes to liing capacity Liing capacities do not exceed 85% of tipping load. Weight of hook blocks and slings is part of the load, and is to be deducted from the capacity ratings. Consult operation manual for further details. Note: Data published herein is intended as a guide only and shall not be construed to warrant applicability for liing purposes. Crane operation is subject to the computer charts and operation manual both supplied with the crane.
LOAD CHART - MAIN BOOM With Offset Jibs T 340-1 XL 11,000 s 0% 360º Standard ASME B.5 0 Offset 32 Offsettable Jib Offset Offset 43 47 51 56 62 68 74 80 87 94 1 8 9,0 8,800 8,400 7,600 6,0 5,000 4,0 3,0 2,400 1,900 1,400 900 51 55 59 64 69 75 81 87 93 99 5 1 8,400 8,0 7,700 6,0 5,0 4,400 3,800 2,900 2,0 1,800 1,400 900 57 61 65 70 75 80 85 91 97 2 7 113 6,500 6,0 6,0 5,900 5,000 4,0 3,400 2,800 2,0 1,700 1,0 800 0 Offset 49 Offsettable Jib Offset Offset 47 52 58 65 72 79 86 93 1 8 1 2 5,000 4,700 4,400 4,000 3,700 3,500 3,0 2,000 1,500 1,0 700 57 63 69 76 83 89 95 2 8 114 1 3,0 3,0 3,0 2,900 2,800 2,700 2,400 1,900 1,400 1,000 66 71 76 82 89 95 1 7 113 119 5 2,500 2,400 2,400 2,0 2,0 2,0 1,700 1,0 900 On Tires 11,000 s On tires 29.5 X 25-28PR Over Rear Standard ASME B.5 Boom Travel Speed: Boom straight over rear 0 mph Creep 2.5 mph 33.75 21,700 21,700 16,500 33.75,600,600 14,900 45,800,800,700 45 8,500 8,500 8,500 25 45 5,800 5,800 5,800 45 3,800 3,800 3,800 35 57 2,500 2,500 2,500 40 57 1,700 1,700 1,700 45 57 1,000 1,000 1,000 Notes to liing capacity Liing capacities do not exceed 85% of tipping load, (75% of tipping load on tires). Weight of hook blocks and slings is part of the load, and is to be deducted from the capacity ratings. Consult operation manual for further details. Note: Data published herein is intended as a guide only and shall not be construed to warrant applicability for liing purposes. Crane operation is subject to the computer charts and operation manual both supplied with the crane. 11
TECHNICAL DESCRIPTION Boom Standard configuration: Full power extension via foot pedal control 4 sections Minimum / Maximum T 340-1 T 340-1 XL / 94 33.75 / 5 Maximum tip height T 340-1 T 340-1 XL 99 1 Boom elevation angle range (min. / max.) T 340-1 -4 / 77 T 340-1 XL -4 / 88 Optional configuration: 32 swing-on jib, fixed length Angular offsets 0º, º, º Maximum tip height with fixed jib T 340-1 9 T 340-1 XL 140 32 49 swing-on jib with 25 extension Angular offsets 0º, º, º Maximum tip height with extended jib T 340-1 147 T 340-1 XL 8 3 or 4 metallic load sheaves Quick reeving design Single nylon sheave Installs only on main boom head, compatible with extendable and fixed swing-on jibs 4 sheave 40 USt Quick reeving design Top swivel ball with hook and latch 7 USt Hoist, Rope and Hook Standard configuration: Two speed ratios 1st layer without load (low range / high range) 5th layer without load (low range / high range) 167 /min / 335 /min 242 /min /487 /min Maximum line pull 1st layer (low speed/ high speed) 5th layer (low speed/ high speed) Permissible line pull,639 / 7,298,827 / 5,052 9,000 6x19 IWRC XIPS Rope diameter 5/8 in Maximum usable 455
TECHNICAL DESCRIPTION Hoist, Rope and Hook Optional configuration: Two speed ratios 1st layer without load (low range / high range) 5th layer without load (low range / high range) 167 /min / 335 /min 242 /min /487 /min Maximum line pull 1st layer (low speed/ high speed) 5th layer (low speed/ high speed) Permissible line pull,639 / 7,298,827 / 5,052 9,000 Rotation resistant compacted strand 18 x 19 Rope diameter 5/8 in Cab, Controls, Operator aids and Load limiter / Load indicator Standard configuration: Upper cab: Sliding door on le side Sliding window on the right side Tilting, tinted glass skylight Removable front windshield Six-way adjustable seat with armrest dual-axis electro-proportional joysticks Joystick control for hoist(s), swing and boom elevation Foot pedals for swing brake, boom telescope and engine rpm Hand control for engine rpm Lower cab: Hinged door on le side with roll-down window Sliding window on the right side Six-way adjustable seat with seatbelt Cruise control Two speed windshield wiper with washer Rated capacity indicator with pictograph display of boom radius, boom angle, boom length, allowable load, actual load and % of allowable load Settable alarms for swing angle, boom length, boom angle, tip height and work area exclusion zone Optional configuration: Upper cab: Air conditioning hydraulically powered Heater and air conditioning package hydraulically powered Liquid Propane (LP) Cab Heater Single-Axis armrest mounted controls Work Lights Upper cab remote carrier control AM/FM radio with cassette Lower cab: Jacobs engine brake 13
TECHNICAL DESCRIPTION Superstructure Standard configuration: Foot pedal actuated multi-disc brake and air actuated house lock 360 Hydraulic driven double planetary reduction gear drive 2.5 rpm Counterweight Three counterweight packages available 2,000 / 7,0 / 11,000 s Tires Standard configuration: Aluminium wheels with stainless hub covers Front Tires Rear Tires 445/65 R22.5-PR 11 R22-14PR Vehicle performance Standard configuration: Theoretical maximum Manual transmission 56% Automatic transmission 64% Manual transmission Automatic transmission 60 mph 60 mph Hydraulic system Triple Pumps: Hoist pump Boom li / telescope Outriggers / swing Single pump: Power Steering Full Flow with bypass protection: Suction Return Pressurized tank with sight level gauge Standard configuration: 60.3 gal/min @ 3,500 psi 45.1 gal/min @ 3,500 psi 22 gal/min @ 2,500 psi 8 gal/min @ 2,000 psi 52.7 gal/min @ 4,500 psi 250 micron screen 5 micron filter 91 gal 14
TECHNICAL DESCRIPTION Carrier, Engine and Drive-line Turn radius to centerline of tires Standard configuration: 34 Axle drive system Air brakes with ABS, Air release / spring set 6 x 4 drive Engine and transmission, EPA 17 compliant, CARB 17 certified Cummins L-9 Intake: Turbocharger with intercooler Rated power Eaton Fuller -speed manual transmission Fuel type: Diesel 8.9 L / 0 hp @ 2,000 rpm Fuel tank capacity 60 gallon Voltage VDC 2 Batteries 1,000 CCA each Alternator 1 amp Optional configuration: Engine and transmission, EPA 17 compliant, CARB 17 certified Cummins L-9 Intake: Turbocharger with intercooler Rated power Allison 7-speed automatic transmission with lock-up torque converter Fuel type: Diesel 8.9 L / 0 hp @ 2,000 rpm Engine and transmission, Non-EPA compliant Cummins QSC Intake: Turbocharger with intercooler Rated power Eaton Fuller -speed manual transmission Fuel type: Diesel 8.3 L / 275 hp @ 2,0 rpm
Effective Date: August 17. Product specifications and prices are subject to change without notice or obligation. The photographs and/or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and/or its subsidiaries in the USA and other countries. All rights are reserved. Terex is a registered trademark of Terex Corporation in the USA and many other countries. Copyright 17 Terex Corporation. Terex Cranes, Global Marketing, Dinglerstraße 24, 66482 Zweibrücken, Germany Tel. +49 (0) 6332 8, Email: info.cranes@terex.com, www.terex.com/cranes www.terex.com/cranes Brochure Reference: TC-DS-I-E-TC 340-1XX 08/17 16