Outdoor Outdoor Rigid Light L-ELSK1 Outdoor Rigid Light L-ELSK1 L-ELSK1 1
Outdoor Rigid Light L-ELSK1 Dot-free Linear light with three surface emitting Application For under bench, steps, handrails in landscape area, indirect light for facade, and the recessed lighting installation with no direct sunlight Recessed light Indirect light for outdoor Landscape 1 Azumaen Location: JAPAN Architect office: GOSiZE Co.,Ltd. Construction: Tanigawa Construction Campany Co.,Ltd. Photo: GOSiZE Co.,Ltd. L-ELSK1 Dai Nagoya Building 24th floor office Location: JAPAN Architect office: ZYCC CORPORATION Nagoya office Lighiting Design: Fujico Co.,Ltd. Nagoya Branch Construction: Meisei Denki Kougyou Photo: SPACE MAN Washizu Kuniyuki The Prince Gallery Tokyo Kioicho Location: JAPAN Architect office: Nikken Sekkei Ltd Interior design: Rockwell Group, Europe Lighting design: Lighting Planners Associates Construction: KAJIMA CORPORATION / TEKKEN CORPORATION / Kumagai Gumi Co.,Ltd. Consortium Photo: TOSHIO KANEKO
Smooth light by dotless, three-sided emission LEDs bar is ideal for under the bench and steps in the landscape. In particular, it is recommended when the surface to be irradiated is a glossy material. You don't need to make any light box for erasing the dots, and you don't need to worry about poor lighting effect caused by LED strips dropping from the aluminium profile. Strip light 250 Dot-free type Advanced waterproofing function design Comparison of the distance from wall 0mm 12 kinds of length variation 120 mm increments, min.140mm and max. 1460 mm can be used for complicated shape installation. Max. connectable length is 6.9 m Recommended where the power supply installation location and the light fixture location are apart from each other. 4 Color variations 4000K, 3500K, 3000K, 200K Available recessed installation for making exposed straigh light effect LEDs bar can be installed as exposed linear light in except for where the sun directly strike it. By using lift clip, the connector can be put below the LED fixture. IP6 connector (Japanese brand) Heatproof fluororesin cable covered with weather resistance Cylindrical extruded polycarbonate diffused cover. Encapsulated by silicon around cable and Polycarbonate end cap. 50mm 100mm High efficiency LED Achieved. W/m, 80 lm/m and 101.3 lm/w using Nichia high efficiency LED package. 200mm MADE IN JAPAN Easy dimming with 24 VDC low voltage power supply Dimmable by any signal such as 0-10 V, DMX, DALI, etc, if you use an adaptive dimming driver, with simple wiring. Ideal for dimming the whole in synchronization. Although it is unsuitable for design that requires individual control. 300mm Outdoor Outdoor Rigid Light L-ELSK1 * mm L-ELSK1 2
Dot-free Linear light with three surface emitting Model No. Light distribution curve -reference- L - ELSK1 - - 24 Length code Lead wire Light source color 014 026 038 050 062 04 086 098 110 122 134 146 J : Both ends lead wire E : One end lead wire 40 : 4000K 35 : 3500K 30 : 3000K 2 : 200K 160 cd 250 (Longitudinal direction 120 ) Width direction Longitudinal direction Specification Length code 050 098 146 Model No. Both ends lead wire L-ELSK1-050J -24 L-ELSK1-098J -24 L-ELSK1-146J -24 One end lead wire L-ELSK1-050E -24 L-ELSK1-098E -24 L-ELSK1-146E -24 Power consumption 3.9W/503mm.W/983mm 11.6W/1463mm Lamp fitting length (L) 503mm 983mm 1463mm Weight 55g(J) / 53g(E) 95g(J) / 93g(E) 135g(J) / 133g(E) Luminaire efficacy (200K) 100.0 lm/w 101.3 lm/w 100.0 lm/w Light source color = Device inventory * = Equivalent 40 4000K 430 lm 850 lm 1280 lm 35 3500K 400 lm 810 lm 1210 lm 30 3000K 400 lm 90 lm 1190 lm 2 200K 390 lm 80 lm 1160 lm Contact us about 5000K since they are made-to-order and have a Minimum Order Quantity. Size Variation Length code 014 026 038 062 04 086 110 122 134 Power consumption 1.0W 2.0W 2.9W 4.8W 5.8W 6.8W 8.W 9.6W 10.6W Lamp fitting length (L) 143mm 263mm 383mm 623mm 43mm 863mm 1103mm 1223mm 1343mm Spec may be subject to change without announcement. The optical data provided on the each product pages are for reference only; the data values are not guaranteed. Please use as reference materials for your planning. General Specification External dimensions Input voltage DC24V Environment In & Outdoors (no condensation) IP65 Max. sets connectable 6.9m Ambient temperature / humidity -5~40 C 25~95%RH (no condensation) Both ends lead wire Cross section view 13.6 Storage temperature / humidity Material (body) Attachments -15~55 C 25~85%RH (no condensation) Polycarbonate Mounting clip 13.2 25.8 One end lead wire 100 L±3 100 16.5 Option parts Mounting clip, Lift clip, Power supply cable, Joint cable Cross section view Dimmable Power Supplies Required 13.6 COO Japan 13.2 25.8 100 L±3 Max. connectable length per power supply * = for multiple systems Normal operation Power supply 4.4m 50W switching power supply 8.8m* 100W switching power supply 13.2m* 150W switching power supply Prohibited installation places: - water directly fall on or pooled - the sunlight directly shines on - liquids including chroline or chemicals fall on - high temperature and high humidity such as saunas and public bath - coastal areas which are affected by sea spray Caution: Do not cut the lead wire of outdoor product at a job site. Please do appropriate treatment for the lead wire and connector of the terminal of outdoor LED fixture. 3 L-ELSK1
Optional parts Mounting clip for Attachment Option Parts Model No : ELSK-FS Used for installing the light appliance. Attachment 2 pcs for 143mm to 383mm 3 pcs for 503mm to 863mm 5 pcs for 983mm to 1463mm Option Parts 2 pcs/1 bag Top view φ4.2 4.2 Side view 15.3 24.2 Outdoor Outdoor Rigid Light L-ELSK1 24.2 Lift clip for Option Parts Model No : ELSK-FH 2 pcs/1 bag Recommended number of Lift clip, 2 pcs for 143mm to 383mm 3 pcs for 503mm to 863mm 5 pcs for 983mm to 1463mm Power supply cable EPYJ *mm Option Parts Required Top view (+ side) 4.6 4.3 (40) 20 L 16.5 6. Check the label on the DC + side for polarity. 4 Joint cable EEJJ *mm Option Parts Top view 15.3 12 Top view φ4.2 29 19 Side view 29 16 16 *(Length:mm) 500 1000 2000 4000 Model No. EPYJ220-305-K EPYJ220-310-K EPYJ220-320-K EPYJ220-340-K Sid e view *(Length:mm) 500 1000 2000 4000 6000 Model No. EEJJ220-305 EEJJ220-310 EEJJ220-320 EEJJ220-340 EEJJ220-360 4.6 Side view 25.8 L 16.5 6. L-ELSK1 4
Installing the product Screw hole of 4.2mm in diameter There is a flange at the end cap in order to prevent the mounting clip from coming off. Connector (Power source side) Connector (Feed side) Insert until it is locked Small space Considering the elasticity of the case, make a small space of 1-2mm. Lead extended horizontally Lead extended downward Possible to extend the lead aside Attachment Option Parts Mounting clip for (ELSK-FS) Fix the lamp on the installation site with the attached Mounting clips and screws (round head screw M3.1 x 16). Cautions Not suitable to be fixed with a double-sided tape or adhesive. Join the connectors. Make sure that they are correctly joined. Use the one side connector product (L-ELSK1-xxxE*-24) for the end of connection. Cautions Do not cut off the connectors to use them. The waterproof performance will be lost. Place the lead towards the direction according to each usage. Cautions In order to avoid the exposure to direct sunlight, hide the connectors behind the lamp, etc. Cautions Make sure that the installation site is flat. Before the construction, make sure to remove from the installation site any oil content, water drop, dust and so on. When installing the product downward or in a vertical direction, pay full attention in order to avoid dislocation, damage due to a fall and so on. Do not scratch or incise the lead wire. The waterproof performance will be lost. Make sure to insert the connector until it is completely locked. Otherwise it can lead to the lowering of the waterproof performance and contact failure. Minimum size for construction Please keep the following size in order to avoid the temperature increase of the lamp. Any size that is smaller than the following may shorten the lamp's life. Mounting clip for Cove lighting Sideways Sealed (the size is the same for both upward and downward) Over 40 Over 100 Over 50 Over 50 Under 35 Through hole of the connector Over 40 10 Under 30 Over 30 Lift clip for Embedded in a building 29 25 unit of measure=mm 5 L-ELSK1
COSEL Connecting to the power supply Cables used for connecting LED fixtures and Power supply must be a suitable type and gauge. Cables should be joined with suitable terminal block or methods as appropriate to the installation and operating environment. Caution: When using a long cable with thin dimension, the resistance of cable will increase. Voltage drop and heat dispatching may occur and result in brightness decreasing. Caution: When separating one cable to multiple circuits in the same gauge, the current loading focuses on the junction of the branch circuit and high temperature will liberate on there.please consider the loading of the power supply (quantity of LED fixture) and review the wiring system to avoid the above problem. Option Parts Required Power supply cable EPYJ 500mm, 1000mm, 2000mm, 4000mm (EPYJ220-305-K, EPYJ220-310-K, EPYJ220-320-K, EPYJ220-340-K) with connector AC input side Outdoor Outdoor Rigid Light L-ELSK1 When connecting the dimmer driver with power supply, unpredicted noise might occur. It is a characteristic of electronic devices, not a malfunction of the LED fixture. Please choose an appropriate power supply and consider a place to install. Reducing the loading factor of LED fixture might improve the noise from the power supply while the noise for the LED fixtures might be improved by splitting the circuit of LED fixtures into multiple. DC output side (Connected to LED fixture) ********* E PS MADE IN JAPAN 出力 :DC**V *.*A 50-60Hz ***VA :AC***-***V 入力 直流安定化電源コーセル株式会社 SPLFA***F-** power supply System configuration diagram Max. connectable length depends on the wattage of the power supply. Max. length per circuit of is 6.9m. If it exceeds 6.9 m, please split into multiple circuits. Max. distance from the power supply to the end of LED fixture is 10.9 m. Max. connectable length per power supply Length of LED fixture Power supply (0% loading factor) *=for multiple system 4.4m 50W power supply 8.8m* 100W power supply 13.2m* 150W power supply Power supply DC24V Up to 4m LED fixture max. 6.9m Circuit 3 Circuit 1 Circuit 2 Option Parts Required Power supply cable EPYJ 500mm, 1000mm, 2000mm, 4000mm (EPYJ220-305-K, EPYJ220-310-K, EPYJ220-320-K, EPYJ220-340-K) L-ELSK1 6
Singapore World HQ 52A Tanjong Pagar Road, Singapore 08843 Tel: +65-6291-2410 Hong Kong Marketing Office Room 1801, 18/F, Kwai Hung Holdings Centre, 89 King's Road, North Point, Hong Kong Tel: +852-2219-8462 Dubai Marketing Office 5WA 331, DAFZA, Dubai, United Arab Emirates Tel: +91-54-446-0350 General Inquiry E-mail: info@luci.co.jp 201.6