Welded Nipples - Black & Galvanized Standard Schedule 40, XH Schedule 80 q FIG. 9: Standard Black Schedule 40 q FIG. 8: Extra Heavy Black Schedule 80 q FIG. 4: Standard Galv. Schedule 40 q FIG. 42: Extra Heavy Galv. Schedule 80 Specifications Dimensions: ASTM A7 (See table below for standard sizes) Threads: NPT per ASME B.20. Material: ASTM A5 Welded Steel Finish: Black, Hot Dip Galvanized, or Zinc Electroplated Standard and Extra Heavy Right and Left Nipples available in /8" - 4" diameter and 4" or 6" lengths. See Special Design Nipples on page 5 for more information. OUTSIDE DIAMETER TOLERANCES PIPE SIZE /8" - /2" 2" - 8" LENGTH ± /6" TOL. ±/64 ± % OF NOMINAL O.D. Nipples over 2" long have a length tolerance of +/- 8". O.D. Length Close Nipple Lengths in in in 8 0.405 4 2 2 2 2 2 4 4 2 5 5 2 6 7 8 9 0 2 4 0.540 7 8 2 2 2 2 2 4 4 2 5 5 2 6 7 8 9 0 2 8 0.675 2 2 2 2 2 4 4 2 5 5 2 6 7 8 9 0 2 2 0.840 8 2 2 2 2 2 4 4 2 5 5 2 6 7 8 9 0 2 4.050 8 2 2 2 2 2 4 4 2 5 5 2 6 7 8 9 0 2.5 2 2 2 2 2 4 4 2 5 5 2 6 7 8 9 0 2 4.660 5 8 2 2 2 2 4 4 2 5 5 2 6 7 8 9 0 2 2.900 4 2 2 2 2 4 4 2 5 5 2 6 7 8 9 0 2 2 2.75 2 2 2 2 4 4 2 5 5 2 6 7 8 9 0 2 2 2 2.875 2 2 2 4 4 2 5 5 2 6 7 8 9 0 2.500 2 5 8 2 4 4 2 5 5 2 6 7 8 9 0 2 2 4.000 2 4 2 4 4 2 5 5 2 6 7 8 9 0 2 4 4.500 2 7 8 4 4 2 5 5 2 6 7 8 9 0 2 5 5.56 4 2 5 5 2 6 7 8 9 0 2 6 6.625 8 4 2 5 5 2 6 7 8 9 0 2 Note: Other lengths available upon request. 8" available as POA - contact your Anvil Representative for details. Project: Address: Contractor: Engineer: Submittal Date: Notes : Notes 2: PF-.6 PROJECT INFORMATION APPROVAL STAMP q Approved q Approved as noted q Not approved Remarks:
Specifications Unless otherwise specified welded nipples ASTM A 5 are furnished on orders for steel nipples in standard and extra strong sizes 8" 8" NPS (6 200 DN). Welded steel nipples (A 5 Type F or Type E) are available in standard and extra strong sizes 8" 8" NPS (6 200 DN), right hand threads, black or galvanized. Seamless nipples manufactured for the U.S. and International markets are not phosphate coated. Seamless nipples manufactured for Canada are phosphate coated. Seamless steel pressure tube nipples (ASTM A 06 Grade B) are available in standard and extra strong sizes 8" 8" NPS (6 200 DN) with right hand threads, black only. Right and left steel nipples are available in standard and extra heavy weight sizes 8" 4" NPS (8 50 DN), in 4" (02mm) and 6" (52mm) lengths. Nipples are available from stock in 8" 8" NPS (6 200 DN) diameter, close to 2 NPS (00 DN) in length. s " 24" NPS (25 600 DN). (Prices on application.) Steel pipe nipples meet ASTM A7. 8" Schedule 40 and 80 galvanized nipples are all electroplated. Identification Where possible, each seamless pipe nipple is identified with the following: A trade mark Seamless designation SMLS schedule 40, 80, 60, XXS Material designation Heat number for traceability Standards and Specifications Dimensions Material Thread Federal/Other PIPE NIPPLES Steel - Welded ASTM A7 ASTM A5 Type F or Type E ASME B.20. WWN 5 Steel - Seamless (High Temp.) ASTM A7 ASTM A06 Gr. B ASME B.20. WWN 5 Brass ASTM B687 ASTM B4 ASME B.20. WWN 5 PF-.6
Steel Nipples Welded Ready Cut Standard Schedule 40 A ASSORTMENTS Mixed Cartons (Black Figure 9 & Galvanized Figure 4) 66 PACKS OR ASSORTED 6 CARTONS Black Figure 9 & Galvanized Figure 4 Close ½" 2" 2½" " ½" 4" 4½" 5" 5½" 6" 2 4 2 2 2 2 2 25 5.00 2 20 0 5 0 0 5 0 5 5 5 5 00 8.00 4 4 2 2 2 2 2 25 7.00 4 20 0 5 0 0 5 0 5 5 5 5 00 24.00 5-5 0 2 5 5 4 75 24.00 5-5 2 2 2 2 2 25 0.00 4 5-5 2 2 2 2 2 25 2.00 2 5-5 2 2 2 2 2 25 5.00 2 6 - - 2 25 22.00 HANDY PACK ASSORTMENTS Mixed Cartons (Black Figure 9 & Galvanized Figure 4) Close ½" 2" 2½" " ½" 4" 4½" 5" 5½" 6" Close ½" 2" 2½" " ½" 4" 4½" 5" 5½" 6" 8 6 6 6 6 6 6 6 6 6 6 6 66 6.00 4 6 6 6 6 6 6 6 6 6 6 6 66 9.00 8 6 6 6 6 6 6 6 6 6 6 6 66 2.00 2 6 6 6 6 6 6 6 6 6 6 6 66 4.00 4 6 6 6 6 6 6 6 6 6 6 6 66 9.00 6-6 6 6 6 6 6 6 6 6 60 26.00 4 6-6 6 6 6 6 6 6 6 6 60.00 2 6-6 6 6 6 6 6 6 6 6 60 4.00 2 6 - - 6 6 6 6 6 6 6 6 54 5.00 8 6 6 6 6 6 6 6 6 6 6 6 66 6.00 4 6 6 6 6 6 6 6 6 6 6 6 66 9.00 8 6 6 6 6 6 6 6 6 6 6 6 66 2.00 2 6 6 6 6 6 6 6 6 6 6 6 66 4.00 4 6 6 6 6 6 6 6 6 6 6 6 66 9.00 6-6 6 6 6 6 6 6 6 6 60 26.00 4 - - 27 9.00 2 - - 27 2.00 2 - - 27 0.00 PF-.6
Steel Nipples Welded Ready Cut Standard Schedule 40, XH Sch. 80 SINGLE RUN PACKS Black Figure 9 & Galvanized Figure 4 SINGLE RUN PACKS Black Only Extra Heavy Figure 8 Close ½" 2" 2½" " ½" 4" 4½" 5" 5½" 6" 8.00 4.50 8 2.00 2 2.50 4.50-0 5.00 4-0 7.00 2-0 8.00 2 - - 9 0.00 2 2 - - - 8.0 - - - 8 5.80 Close ½" 2" 2½" " ½" 4" 4½" 5" 5½" 6" 2.20 4 4.0-0 6.0 4-0 8.40 2-0 0.0 2 - - 9.90 READY CUT PIPE Black Extra Long Figure 9 & Galvanized Figure 4 8" 24" 0" 6" 42" 48" 54" 60" 66" 72" 8 5 5 5 5 5 5 5 5 5 5 4 5 5 5 5 5 5 5 5 5 5 8 5 5 5 5 5 5 5 5 5 5 2 5 5 5 5 5 5 5 5 5 5 4 5 5 5 5 5 5 5 5 5 5 4 2 2 2 2 2 2 2 2 2 2 2 2 TRAVEL TRAYS Black Figure 9 & Galvanized Figure 4 Close ½" 2" 2½" " ½" 4" 4½" 5" 5½" 6" 2 6 6 6 6 6 6 6 6 6 6 6 66 5.00 4 6 6 6 6 6 6 6 6 6 6 6 66 20.00 5-5 5 5 5 5 5 5 5 5 50 22.00 PF-.6
Special Design Nipples Beck Nipples are available with a variety of options for customization. To order, begin by selecting the figure number, material, finish, and end treatments from the table below. Then, select the nominal pipe size and specify the length rounded to the nearest /6". Contact your Anvil Representative for additional options. Fig No. Description Material Finish End # End #2 NPS Length Sch. 40 Seamless Nipple A ASTM A06 GR B A Plain with Zinc Phosphate Coating A NPT A NPT 8 20SD 4 Special Design B ASTM A B Plain with Sandblasted Surface B PLN B PLN 8 Sch. 40 Seamless Nipple - A ASTM A06 GR B A Hot Dip Galvanized per ASTM A5 C PSQ C PSQ 2 0SD Galvanized B ASTM A B Zinc Electroplated per ASTM B6 D PDB D PDB 4 Special Design - - C Zinc Electroplated with Yellow Chromate E ROE E ROE Up to 24" 4 Maximum XH/Sch. 80 Seamless Nipple A ASTM A06 GR B A Plain with Zinc Phosphate Coating F BEV F BEV 2 25SD Specify to the Special Design B ASTM A B Plain with Sandblasted Surface G NPL G NPL 2 nearest 6" 2 2 XH/Sch. 80 Seamless Nipple - A ASTM A06 GR B A Hot Dip Galvanized per ASTM A5 H NPM H NPM 5SD Galvanized B ASTM A B Zinc Electroplated per ASTM B6 I ISO I ISO 4 Special Design - - C Zinc Electroplated with Yellow Chromate J GRV J GRV 5 Sch. 60 Seamless Nipple A ASTM A06 GR B A Plain with Zinc Phosphate Coating K LHT K LHT 6 26SD Special Design B ASTM A B Plain with Sandblasted Surface End Codes Sch. 60 Seamless Nipple - A ASTM A06 GR B A Hot Dip Galvanized per ASTM A5 Standard NPT Thread per NPT SD Galvanized B ASTM A B Zinc Electroplated per ASTM B6 ASME B.20. (RH) (TOE) Special Design - - C Zinc Electroplated with Yellow Chromate PLN Plain End/Roller Cut XXH Seamless Nipple A ASTM A06 GR B A Plain with Zinc Phosphate Coating PSQ Plain End with Square or Saw Cut 27SD Special Design B ASTM A B Plain with Sandblasted Surface Plain End with Square Cut PDB XXH Seamless Nipple - A ASTM A06 GR B A Hot Dip Galvanized per ASTM A5 and Deburred 29SD Galvanized B ASTM A B Zinc Electroplated per ASTM B6 Ream One End - Square Cut ROE Special Design - - C Zinc Electroplated with Yellow Chromate End with Ream Sch. 40 Welded Nipple A ASTM A5, Type F, CW A Plain with Zinc Phosphate Coating BEV Square Cut End with 7 9SD 2 Bevel Special Design B ASTM A5, Type E, EW B Plain with Sandblasted Surface NPSL Straight Thread per ASME NPL Sch. 40 Welded Nipple - A ASTM A5, Type F, CW A Hot Dip Galvanized per ASTM A5 B.20. (Locknut) (Toe) 4SD Galvanized B ASTM A5, Type E, EW B Zinc Electroplated per ASTM B6 NPSM Straight Thread per ASME NPM Special Design - - C Zinc Electroplated with Yellow Chromate B..20. (Mechanical) (Toe) XH/Sch. 80 Welded Nipple A ASTM A5, Type F, CW A Plain with Zinc Phosphate Coating ISO ISO/BSPT Taper Threads per ISO 7/ 8SD Special Design B ASTM A5, Type E, EW B Plain with Sandblasted Surface GRV Cut Grooved End per Anvil Specification XH/Sch. 80 Welded Nipple - A ASTM A5, Type F, CW A Hot Dip Galvanized per ASTM A5 NPT-LH / Left Handed NPT Thread LHT 42SD Galvanized B ASTM A5, Type E, EW B Zinc Electroplated per ASTM B6 per ASME B..20. (TOE) Special Design - - C Zinc Electroplated with Yellow Chromate 4SD A Plain with Zinc Phosphate Coating Tank Nipple - Sch. 40 B Plain with Sandblasted Surface Welded A ASTM A5, Type E, EW C Zinc Electroplated per ASTM B6 Special Design D Zinc Electroplated with Yellow Chromate 44SD A Plain with Zinc Phosphate Coating **Butt Nipple - Sch. 40 A ASTM A5, Type F, CW B Plain with Sandblasted Surface Welded C Zinc Electroplated per ASTM B6 Special Design B ASTM A5, Type E, EW D Zinc Electroplated with Yellow Chromate A Plain with Zinc Phosphate Coating 45SD Mining Nipple - Sch. 40 B Plain with Sandblasted Surface Welded A ASTM A5, Type E, EW C Zinc Electroplated per ASTM B6 Special Design D Zinc Electroplated with Yellow Chromate Special Design Seamless Nipple A Plain 62SD A ASTM B4 Brass Brass & Chromium Plated Brass B Chrome Plated Special Design Grooved Adapter A Plain 6SD A ASTM B4 Brass Nipple - Aluminum & Brass B Chrome Plated ** NPS and lengths available POA, upon request. Contact your Anvil Representative for details. PF-.6
Special Design Nipples TANK NIPPLES FIG. 4SD - Black & Galvanized All Tank Nipples ship in quantities of 25. Not intended for pressure service. Description Length Weight Tank Nipples are recommended for use as tank legs, not intended for pressure service. Tank Nipples have standard NPT threads on one end and straight NPSM threads running for 4" on the other end. Tank Nipples are fabricated from ASTM A5 Schedule 40 welded pipe. 8 6 0. 4 6 0.20 8 6 0.28 2 6 0.40 4 6 0.5 6 0.76 4 6.04 2 6.28 2 6.56 BUTT NIPPLES FIG. 44SD - Black & Galvanized Description Butt Nipples are intended for joining couplings or female threaded components end to end without exposing male threads. Butt Nipples have standard NPT male threads on both ends. Threads may have fewer imperfect threads due to reduced nipple length. Butt Nipples are fabricated from ASTM A5 Schedule 40 welded pipe. Length Weight Quantity 2 4 0.28 25 2 2 2 0.87 0 2.28 0 4 2 4. 5 RIGHT & LEFT NIPPLES Black Figure 9SD & Galvanized Figure 4SD Length Weight Quantity 8 4" or 6" 0.09-4 4" or 6" 0. - 8 4" or 6" 0.8 25 2 4" or 6" 0.25 25 4 4" or 6" 0.5 25 4" or 6" 0.5 25 4 4" or 6" 0.68 25 2 4" or 6" 0.80 25 2 4" or 6".09 25 2 2 4" or 6".50-4" or 6" 2.00-2 4" or 6" 2.80-4 4" or 6".24 - General Assembly of Threaded Fittings ) Inspect both male and female components prior to assembly. Threads should be free from mechanical damage, dirt, chips and excess cutting oil. Clean or replace components as necessary. 2) Application of thread sealant Use a thread sealant that is fast drying, sets-up to a semi hard condition and is vibration resistant. Alternately, an anaerobic sealant may be utilized. Thoroughly mix the thread sealant prior to application. Apply a thick even coat to the male threads only. Best application is achieved with a brush stiff enough to force sealant down to the root of the threads. ) Joint Makeup For sizes up to and including 2" pipe, wrench tight makeup is considered three full turns past handtight. Handtight engagement for 2" through 2" thread varies from 4 2 turns to 5 turns. For 2 2" through 4" sizes, wrench tight makeup is considered two full turns past handtight. Handtight engagement for 2 2" through 4" thread varies from 5 2 turns to 6 4 turns. PF-.6