2EVP-A SERIES Vertical In-Line Self-Priming Centrifugal Pumps for Petroleums and Solvents PUMP: Heavy-duty cast iron construction, with 2 NPT female threaded, in-line suction and discharge ports. This compact, vertical design is self-supporting and requires a minimum of floor space. The self-priming feature allows the pump to be mounted above the liquid and suction lifts of 1 to 2 can be achieved, depending on the liquid and the pump model. Diffuser priming eliminates the need for a check valve and reduces radial loads insuring longer bearing life. These pumps are sealed by a self-lubricating, Viton mechanical shaft seal. When used on a suction lift any leakage that may occur will be STANDARD UNIT INCLUDES: down into the pump rather than up the motor shaft as the seal is on the suction side of the impeller. MOTOR: Single phase motors are 6 cycle, 115/2 volt, except 2 HP explosion proof motors which are 2 volt only. Three phase motors are 6 cycle, 2/46 volt and all are 45 RPM motors. All explosion proof motors are Class I, Group D, Code: TB. OPTIONAL MOUNTING: All models fit the lightweight, two wheel chassis. Kit illustrated in Section 8. OPTIONAL SEAL: Kalrez mechanical seals are available. Contact factory for more information. 24 ITT Water Technology, Inc. Effective November, 24 MB275 ITT Industries 1
CAPACITY IN U.S. GALLONS PER MINUTE PUMP SIZE MODEL 1 2 4 5 6 7 8 9 1 9A 112 9 72 2 1A 6 58 51 6 12 2EVP 11A 1 94 84 72 55 15 12A 115 18 1 9 78 65 41 17A 121 12 116 11 12 91 77 6 2 NOTE: Capacities listed are for 5 ft. dynamic suction lift. With higher lifts, capacities will be lower and on flooded suction, capacities will be higher. MAXIMUM STATIC SUCTION LIFT COLD, CLEAR, WATER AT SEA LEVEL MODEL 9A 1A 11A 12A 17A S.L. in Feet 12 14 11 2 2 STANDARD CONSTRUCTION SPECIFICATIONS Casing Close Grained Cast Iron Pump Tank Capacity 1 Gallon Base Close Grained Cast Iron Priming Connection 1 (Plugged) Impeller Nickel Plated Cast Iron Drain Connection /8 (Plugged) Diffuser Nickel Plated Cast Iron Working Pressure 1 PSI Shaft Seal 5 /8 Viton, Stainless and Brass, Self-Lubricating Elastomers Model EVP Viton TYPE IMPELLER AND SOLIDS SIZE PUMP SIZES TYPE 9A 1A 11A 12A 17A IMPELLER OPEN CLOSED Maximum Size Solids Handled 7 /16 /16 /16 /16 /16 2
CROSS SECTION: LEGEND 2EVP CROSS SECTION Key Description Key Description 1 Drain Plug 7 Diffuser 2 Cover 8 Gasket, Diffuser Gasket, Cover 9 Impeller Shim 4 Impeller Nut 1 Impeller Spacer 5 Impeller Washer 11 Seal Assembly 6 Impeller 12 Tank
Petroleum Bulk Plant Usage PERFORMANCE CURVES The performance curves shown in this manual and other published literature were taken from actual tests of standard production pumps and reflect an average performance of the pumps indicated. 2 1 TOTAL HEAD IN POUNDS PER SQUARE INCE - SP. GR..72 2 1 TOTAL HEAD IN POUNDS PER SQUARE INCE - SP. GR..85 4 1 2 75 5 1 25 1A TYPE: 2EVP - A LIQUID: SP. GR..72-.85 SPEED: 45 RPM 9A 11A 17A 12A 25 5 75 1 125 1 2 15 6 5 MODEL: 2EVP - 9A SPEED: 45 RPM POWER: 1 HP MOTOR 1 5 4 2 1 SP. GR. 1. 8 2 4 1 2 4 6 8 1 12 12 1 8 6 4 1 2 4
Petroleum Bulk Plant Usage PERFORMANCE CURVES The performance curves shown in this manual and other published literature were taken from actual tests of standard production pumps and reflect an average performance of the pumps indicated. 1 8 MODEL: 2EVP - 1A SPEED: 45 RPM POWER: 1 HP MOTOR 2 1 6 4 2 SP. GR. 1. 1 2 1.5 1. 1.5 1 2 4 5 6 5 1 1 8 MODEL: 2EVP - 11A SPEED: 45 RPM POWER: 1 1 /2 HP MOTOR 2 1 6 4 SP. GR. 1. 1 1.5 2 2 1. 1.5 2 4 6 8 1 12 1 2 5
Petroleum Bulk Plant Usage PERFORMANCE CURVES The performance curves shown in this manual and other published literature were taken from actual tests of standard production pumps and reflect an average performance of the pumps indicated. 1 8 MODEL: 2EVP - 12A SPEED: 45 RPM POWER: 1 1 /2-2 HP MOTOR 2 1 6 4 SP. GR. 1. 2.5 1 2. 2 2 4 6 8 1 12 2 1 1.5 1..5 1 2 12 1 MODEL: 2EVP - 17A SPEED: 45 RPM POWER: 2 HP MOTOR 2 1 8 6 4 2 SP. GR. 1. 2 4 6 8 1 12 1 2 1 2 1 1 2 6
DIMENSIONS: 9 11 /2 /8 9 5 /8 FOR 1 1 /2 AND 2 HP, 1Ø ONLY /4-14 NPT 6 /16 /4-14 NPT 6 1 /2 4787 G A MAX. 4 7 /16 4 7 /16 15 /8 7 /8 9 7 /8 2 NPT SUCTION (FEMALE) 9 /16 DIA. (4) MTG. HOLES ON 11 1 /4 DIA. B.C. 45º FROM CL OF PIPE CONNECTIONS Dimensions shown in inches. 2 NPT DISCHARGE (FEMALE) 12 1 /8 DIA. ALL MOTORS 56 FRAME EXCEPT 1½ AND 2 HP, 1Ø WHICH ARE 184 FRAME EXPLOSION PROOF MOTORS HP Phase Cycle A 1 2½ 1 19½ 1½ 2 1 26 6 1 /8 2½ 26 1 /8 21 7 /8 Dimensions may vary by manufacturer. NOTE: These dimensions are not to be used for construction purposes without formal factory approval. 7
is a brand of ITT Water Technology, Inc. - a subsidiary of ITT Industries, Inc. and the ITT Engineered Blocks Symbol are registered trademarks and tradenames of ITT Industries. PRINTED IN U.S.A. MARLOW PUMPS RESERVES SPECIFICATIONS THE RIGHT ARE TO MAKE SUBJECT CHANGES TO CHANGE IN DESIGN, WITHOUT MATERIALS NOTICE. AND PRICES WITHOUT NOTICE. ITT Industries 8