LABOUR RATE LABOUR:117 LABOUR RATE PER HOUR 55.00 LABOUR:117.1 DAILY LABOUR RATE 605.00 LABOUR:118 PREP ENGINE FOR DYNO(inc. check ecu, loom, fit all sensors etc.) 55.00 LABOUR:118.1 FIT ENGINE TO DYNO, DYNO ENGINE & REMOVE. PER HOUR 69.00 MISC ITEMS LABOUR:001 AQUA BLASTING PER HOUR 60.00 LABOUR:002 CHEMICAL CLEAN PER TANK 41.00 LABOUR:044 REMOVE & REFIT 4 CYL CAMSHAFT BEARING 41.00 LABOUR:044.1 REMOVE & REFIT CAMSHAFT BEARING V8 60.00 LABOUR:045 BAFFLE SUMP 6H 360.00 LABOUR:092 REPAIR PROPSHAFT SEAL "D" JOINT 60.00 LABOUR:154 THROTTLE JACKER COMPLETE 300.00 LABOUR:155 MODIFY FRONT UPRIGHT FOR REIGER DAMPER 180.00 LABOUR:162 DRESS OUT DAMAGE IN COMBUSTION CHAMBRE PER HOUR.. 60.00 REFACING LABOUR:003 BLOCK SKIM 4 CYLINDER 40.00 LABOUR:003.1 SKIM CYLINDER BLOCK 2 CUTS 60.00 LABOUR:004 BLOCK SKIM 6 CYLINDER 50.00 LABOUR:066 HEAD SKIM 4 CYLINDER 40.00 LABOUR:066.1 5 CYLINDER HEAD SKIM 50.00 LABOUR:066.2 SKIM EXHAUST MANIFOLD 40.00 LABOUR:067 HEAD SKIM 4 CYL. DIESEL WITH INSERTS 50.00 LABOUR:068 REMOVE & REFIT PRE-COMBUSTION CHAMBER 5.00 LABOUR:069 HEAD SKIM 6 CYLINDER 50.00 LABOUR:070 HEAD SKIM 8 CYLINDER 80.00 LABOUR:071 HEAD SKIM V12 CYLINDER 100.00 LABOUR:072 HEAD SKIM COMMERICAL 75.00 LABOUR:093 SKIM BRAKE DISC 50.00 LABOUR:094 SKIM BRAKE DRUM 50.00 REBORE LABOUR:005 HONE PER CYLINDER BORE 15.00 LABOUR:006 REBORE PER BORE 30.00 LABOUR:006.1 REBORE PER BORE 2 CUTS 40.00 LABOUR:095 MOTORCYCLE OVERBORE 60.00 LABOUR:096 MOTORCYCLE REBORE 45.00 CRANKSHAFT LABOUR:007 CRANK REGRIND PER JOURNAL CAR STD POA LABOUR:008 CRANK REGRIND PER JOURNAL LARGE POA LABOUR:009 CRANK REGRIND PER JOURNAL SINGLE CYL. M/C POA LABOUR:022 LAP CRANK & MEASURE 4 CYL. 45.00 LABOUR:023 LAP CRANK & MEASURE 6 CYL 60.00 LABOUR:023.1 LAP CRANK AFTER TUFFRIDE 30.00 LABOUR:023.2 LAP CRANK & MEASURE V8 75.00
LABOUR:026 REMOVE & REFIT BUNGS & DESLUDGE CRANKSHAFT 45.00 BALANCING LABOUR:010 CRANK BALANCE 4 CYL 60.00 LABOUR:011 CRANK & FLYWHEEL BALANCE 4CYL 75.00 LABOUR:011.1 BALANCE FLYWHEEL 4 CYL. (on a balance crank) 30.00 LABOUR:012 CRANK FLYWHEEL & CLUTCH COVER BALANCE (1/2) - 4 CYL 90.00 LABOUR:012.1 CRANK, FLYWHEEL & CLUTCH COVER 6 CYL. 1/2 BALANCE 150.00 LABOUR:012.2 BALANCE 4 CYLINDER PISTON SET 40.00 LABOUR:012.3 BALANCE 6 CYL. FLYWHEEL & COVER (on a balance crankshaft) 70.00 LABOUR:012.4 BALANCE 6 CYL CRANKSHAFT 86.00 LABOUR:013 FULL 4 CYL. BALANCE 172.00 LABOUR:014 FULL STRAIGHT 6 CYL. BALANCE 260.00 LABOUR:015 FULL V6 CYLINDER BALANCE 291.00 LABOUR:016 FULL V8 BALANCE 450.00 LABOUR:017 V8 CRANK BALANCE 170.00 LABOUR:017.1 V8 CRANK & FLYWHEEL BALANCE 210.00 LABOUR:018 V8 CRANK FLYWHEEL & COVER BALANCE 240.00 LABOUR:019 V8 PISTON BALANCE 120.00 LABOUR:020 V8 CONROD BALANCE 120.00 LABOUR:115 BALANCE PROPSHAFT PER HOUR 60.00 LABOUR:116 BALANCE CRANKSHAFT PER HOUR 60.00 CONRODS LABOUR:021 RESIZE CONROD 40.00 LABOUR:024 REBUSH CONROD 30.00 LABOUR:024.1 MANUFACTURE CONROD BUSH Inc bronze material 3cm 30.00 LABOUR:024.2 REAM OUT CONROD 20.00 LABOUR:024.3 BORE SMALL END HOUSING 30.00 PISTONS LABOUR:027 MACHINE 4 VALVE POCKET PER PISTON 30.00 LABOUR:027.1 MACHINE PISTON BOWL 30.00 LABOUR:027.2 VALVE CUT OUT (2 CUT OUT PER PISTON) PISTON 20.00 LABOUR:028 MODIFY PISTON TO GIVE 7.5:1 WITH VALVE CUT OUT POCKET 75.00 LABOUR:035 REMOVE & REFIT PISTON TO ROD - CIRCLIP 8.00 LABOUR:036 REMOVE & REFIT PISTON TO ROD - PRESS 10.00 FLYWHEEL LABOUR:029 LIGHTEN FLYWHEEL PER HOUR 60.00 LABOUR:030 FLYWHEEL SKIM CAST IRON 45.00 LABOUR:030.1 SINGLE DOWEL FLYWHEEL 30.00 LABOUR:030.2 DOUBLE DOWEL FLYWHEEL TO CRANK 60.00 LABOUR:031 FLYWHEEL SKIM STEEL 60.00 LABOUR:031.1 SKIM STEP FLYWHEEL 75.00 LABOUR:032 REMOVE & REFIT RING GEAR 30.00 LABOUR:033 MACHINE FLYWHEEL & FIT RING GEAR 60.00 LABOUR:034 DRILL & TAP FLYWHEEL DOWELS FOR CLUTCH 180.00 LABOUR:034.1 DRILL & TAP FLYWHEEL FOR PICK UP & MAKE BRACKET FOR TDC SENSOR 180.00
ENGINE ASSEMBLY TIME LABOUR:046 STRIP - CLEAN - INSPECT COMPLETE ENGINE 60.00 LABOUR:047 STRIP - CLEAN - INSPECT REBUILD COSWORTH ROAD ENGINE OR 16 VALVE 1,800.00 LABOUR:047.1 REMOVE & REFIT WRC RALLY ENGINE TO CAR 30H 1,800.00 LABOUR:048 STRIP - CLEAN - INSPECT - REBUILD RALLYCROSS ENGINE 3,000.00 LABOUR:048.1 STRIP, CLEAN, INSPECT - REBUILD RALLY ENGINE 3,000.00 LABOUR:048.2 BUILD LATEST SPEC RALLYCROSS ENGINE 3,600.00 LABOUR:049 REMOVE & REFIT 4X4 ROAD ENGINE TO CAR 15H 900.00 LABOUR:049.1 REMOVE & REFIT 2WD ROAD ENGINE TO CAR 10H 600.00 LABOUR:053 DUMMY BUILD - TO CHECK CLEARANCES AND VOLUMES 120.00 LABOUR:053.1 STRIP & ASSEMBLE PORSCHE HEAD & SHIM UP 45.00 LABOUR:054 STRIP & REASSEMBLE HEAD 8 VALVE NO CAM 60.00 LABOUR:055 STRIP & REASSEMBLE HEAD 8 VALVE WITH CAM 90.00 LABOUR:056 STRIP & REASSEMBLE HEAD12 VALVE NO CAM 90.00 LABOUR:057 STRIP & REASSEMBLE HEAD 12 VALVE WITH CAMS 120.00 LABOUR:058 STRIP & REASSEMBLE HEAD 16 VALVE NO CAM 90.00 LABOUR:059 STRIP & REASSEMBLE HEAD 16V WITH CAMS 120.00 SHIMMING UP LABOUR:060 SHIM UP 8 VALVE CYLINDER HEAD 90.00 LABOUR:061 SHIM UP 12 VALVE CYLINDER HEAD 120.00 LABOUR:062 SHIM UP 16 VALVE CYLINDER HEAD 180.00 LABOUR:063 SHIM UP 24 VALVE CYLINDER HEAD 270.00 HEAD WORK LABOUR:053.2 SET PORCHE SPRING HEIGHTS X 6 30.00 LABOUR:075.1 MACHINE SPRING SEATS COSWORTH 120.00 LABOUR:075.2 MACHINE SPRING SEATS PINTO 120.00 LABOUR:075.3 SHIM UP VALVE SPRINGS COSWORTH 120.00 LABOUR:075.4 GRIND CAM CLEARANCE FOR ESCORTH WRC 120.00 LABOUR:076 CUT VALVE SEAT FOR BIG VALVE 15.00 LABOUR:077 CUT VALVE SEAT STD VALVE 10.00 LABOUR:078 UNLEADED CONVERSION INC. INSERT STD 40.00 LABOUR:078.1 REMOVE & REFIT INSERT & CUT SEAT FOR BIG INLET VALVE XJ 60.00 LABOUR:078.2 REMOVE & REFIT VALVE SEAT, CUT VALVE SEAT inc. valve seat STD 40.00 LABOUR:078.3 UNLEADED CONVERSION exhaust (inc. insert) with oversize insert. 60.00 LABOUR:078.4 REMOVE & REFIT INLET OVERSIZE INSERTS & CUT (inc. insert) 60.00 LABOUR:079 REMOVE & REFIT VALVE GUIDE 8.00 LABOUR:079.1 FIT BRONZE VALVE GUIDE 8.00 LABOUR:079.2 REMOVE & REFIT BRONZE GUIDE & SIZE 10.00 LABOUR:079.3 MODIFY VALVE GUIDE FOR STEM SEAL 4.00 LABOUR:080 REMOVE & REFIT THINWALL GUIDE INC. GUIDE (BRONZE) 12.00 LABOUR:081 REAM VALVE GUIDE 4.00 LABOUR:082 DECOKE VALVE 5.00 LABOUR:083 REFACE VALVE 7.00 LABOUR:084 LAP VALVE 5.00
LABOUR:153 MODIFY CAMSHAFT FOR WRC SENSOR 60.00 LABOUR:152 MODIFY CAM COVER FOR WRC TDC SENSOR 120.00 PRESSURE TESTING LABOUR:064 PRESSURE TEST 4 CYLINDER 60.00 LABOUR:064.1 HARDNESS TEST 15.00 LABOUR:065 PRESSURE TEST 6 CYLINDER 75.00 PORTING LABOUR:085 MILD PORT CYLINDER HEAD PER HOUR 60.00 LABOUR:086 PORT GROUP A CYLINDER HEAD; inc. reface valves, 1,440.00 cut seats & remove & refit valve guides. LABOUR:087 FULL PORT JAGUAR CYLINDER HEAD & MANIFOLD 540.00 LABOUR:087.1 MILD PORT JAGUAR CYLINDER HEAD 360.00 WELDING LABOUR:088 WELD CYLINDER HEAD PER HOUR 60.00 LABOUR:089 REPAIR & WELD SUMP PER HOUR 60.00 LABOUR:090 WELD CAM COVER per HOUR 60.00 LABOUR:091 ALLEY WELD PER HOUR 60.00 LABOUR:163 PREPARE FOR WELDING 60.00 TIMESERTS LABOUR:097 TO DRILL OUT BROKEN BOLT PER HOUR 60.00 LABOUR:098 TIMESERT M5 TO M9 25.00 LABOUR:099 TIMESERT M10 TO M12 27.00 LABOUR:100 TIMESERT BIG SERT 45.00 LABOUR:101 TIMESERT SPARKPLUG IN WORKSHOP 30.00 LABOUR:102 TIMESERT SPARKPLUG IN CAR 60.00 LABOUR:103 TIMESERT SUMP BUNG PLUG 40.00 TUNING LABOUR:104 MAPPING ECU 60.00 LABOUR:125 LLAMDBA SENSOR BOSS 16.00 LABOUR:125.1 WELD LAMDBA BOSS 30.00 LABOUR:126 MANUFACTURE 4 BAR MAP SENSOR BRACKET 60.00 LABOUR:147 MODIFIED DISTRIBUTOR CAP FOR T6 30.00 LABOUR:148 SPACER FOR CRANK SENSOR FOR T6 15.00 LABOUR:165 AEROQUIP FITTING & PIPE WORK FOR SWEDISH DRY SUMP & TURBO DRAIN 580.00 LABOUR:166 MANUFACTURE OIL PUMP BRACKET 160.00 LABOUR:168 MACHINE SET OF 4 SPARK PLUGS 30.00 LABOUR:170 MACHINE CAMSHAFT FOR TRIGGER 60.00 LABOUR:171 MACHINE CAM COVER FOR PHASE SENSOR 60.00 LABOUR:156 PECTEL ECU AFTERCARE 330.00 EGR LABOUR:127 ASSEMBLE ALS VALVE 120.00 LABOUR:128 ASSEMBLE EGR VALVE 30.00 LABOUR:129 MANUFACTURE ADAPTOR FOR EGR 120.00 LABOUR:129.1 MANUFACTURE COUPLING CENTRE 45.00
LABOUR:129.2 MANUFACTURE STAINLESS STEEL BUTTERFLY PLATE 45.00 TURBO LABOUR:121 STRIP - CLEAN & ASSEMBLE TURBO 240.00 LABOUR:134 MODIFY COMPRESSOR HOUSING TO FIT RESTRICTOR 120.00 LABOUR:139 MANUFACTUR TURBO RESTRICTOR WRC 38MM 480.00 LABOUR:139.1 MANUFACTURE 45MM TURBO RESTRICTOR 480.00 LABOUR:139.2 MACHINE COMPRESSOR HOUSING FOR 45MM RESTRICTOR 120.00 LABOUR:139.3 MODIFY GARRATT EXHAUST HOUSING 90.00 LABOUR:139.4 MACHINE TURBO FOR PRP 60.00 LABOUR:139.5 MACHINE COMPRESSOR HOUSING OPTURMISE CLEARANCE 30.00 LABOUR:139.6 MACHINE COMPRESSOR HOUSING FOR TURBO SPEED SENSOR 60.00 LABOUR:139.7 MACHINE EXHAUST HOUSING FOR Q TRIM 60.00 LABOUR:139.8 MACHINE EXHAUST HOUSING TO MOTORSPORT Q TRIM 60.00 LABOUR:142 WASTEGATE VALVE 60.00 LABOUR:159 JGE60 TURBO - MODIFY WASTEGATE PORT & COMP. HOUSING & WELD ON ACT. 420.00 BRACKET TO FIT CONFIGURE TURBO LABOUR:160 REMOVE OLD UNIT & FIT JGE60 TURBO & REMAP TO SUIT 360.00 TRANSMISSION LABOUR:105 STRIP - CLEAN - INSPECT & REBUILD GEARBOX 600.00 LABOUR:107 STRIP - CLEAN - INSPECT & REBUILD M SPORT GEARBOX 60.00 LABOUR:108 REBUSH M SPORT OIL PUMP 60.00 LABOUR:109 STRIP - CLEAN - INSPECT & REBUILD DIFFERENTIAL 690.00 LABOUR:110 STRIP - CLEAN - INSPECT & REBUILD DIFFERENTIAL GEAR CHANGE 840.00 FABRICATING LABOUR:112 FABRICATE INTERCOOLER 720.00 DURATEC LABOUR:041.4 LINER DURATEC BLOCK TO ORIGINAL BORE SIZE 420.00 LABOUR:048.3 STRIP ENGINE, AND BUILD WET SUMP DURATEC ENGINE 3,640.00 LABOUR:048.4 STRIP, CLEAN & INSPECT DONER ENGINE. DIVISION 2 DURATEC ENGINE 3,600.00 DEBUR AND LIGHTEN BLOCK...BUILD DRY SUMP LABOUR:062.1 SHIM UP 16 VALVE DURATEC HEAD 150.00 LABOUR:086.2 MACHINE DURATEC HEAD FOR BIG VALVES 540.00 LABOUR:086.3 RIKWOODS CNC PORT DURATEC CYLINDER HEAD 1,440.00 LABOUR:086.4 MODIFY HEAD TO CLEAR CAM LOBES DURATEC 180.00 LABOUR:175 MODIFY DURATEC FRONT COVER 120.00 LABOUR:176 MODIFY DURATEC CAM COVER FOR 4 COILS INC. SPACERS 180.00 LABOUR:177 SBD DURATEC INLET MANIFOLD - STRIP & PORT MATCH INLET MANIFOLD TO HEAD, 480.00 REPLACE FUEL RAIL TO JGE BILLET TYPE. MAKE -6 FUEL PIPE TO JOIN RAILS. CORRECTLY ASSEMBLE & ADJUST THROTTLE BODIES. FIT SNORR WASHERS TO ALL MOUNTING BOLTS. FIT AIR FILTER BACK PLATE AND FILTER HYUNDAI
LABOUR:141 CONVERT CYLINDER HEAD TO BIG VALVE 1,560.00 LABOUR:178 MACHINE HYUNDRAI BLOCK & CYLINDER HEAD FOR 11MM STUDS 300.00 JAGUAR (EAGLE RACING) LABOUR:038 MACHINE BLOCK FOR STEP LINER 30.00 LABOUR:039 REMOVE & REFIT CYLINDER LINER 15.00 LABOUR:039.1 CLEAN WATERWAY IN BLOCK 15.00 LABOUR:040 REBORE LINER TO SUIT PISTON 30.00 LABOUR:050 REBUILD EAGLE ENGINE INC. SHIMMING UP STD. 960.00 LABOUR:051 REBUILD EAGLE ENGINE INC. SHIMMING UP EAGLE SPECIAL 1,200.00 LABOUR:052 REBUILD EAGLE ENGINE INC. SHIMMING UP STD. HIGH PERFORMANCE 1,200.00 LABOUR:073 PIN BUCKET SLEEVES 120.00 LABOUR:073.1 REMOVE & REFIT TAPPET SLEEVE 75.00 LABOUR:073.2 MEASURE BUCKET SLEEVES 15.00 LABOUR:073.3 MACHINE HEAD, MAKE SPACERS 3 OF & FIT 3 OF CLAMP PLATES 120.00 LABOUR:073.4 GRIND CAM CLEARANCE 60.00 LABOUR:073.5 BORE TAPPET SLEEVE OVERSIZE 30.00 LABOUR:074 STRAP CORE PLUGS 75.00 LABOUR:164 SS3 7/16" STAINLESS STEEL SPACER 4.00 LABOUR:167 B2 SPIGOT BUSHES BRONZE 60.00 LABOUR:172 JAGUAR S7 COLLAR BUSH 15.00 LABOUR:106 STRIP, CLEAN, INSPECT DONOR GEARBOX. 180.00 LABOUR:106.1 MODIFY BELLHOUSING FROM 3.8 TO 4.2 90.00 LABOUR:106.2 TURN 4.2 TO TAKE MT75 BELLHOUSING 45.00 LABOUR:106.4 MT75 GEARBOX CONVERSION 960.00 LABOUR:106.5 MANUFACTURE GEAR LEVER ASSY 510.00 LABOUR:111 FABRICATE E TYPE 4.2 OR 3.8 OR V12 RADIATOR 600.00 LABOUR:113 MACHINE STEEL WISHBONE 150.00 LABOUR:114 MANUFACTURE ANTI ROLL BAR LINK PAIR 90.00 LABOUR:132 MODIFY CRANK TO TAKE LIP OIL SEAL 120.00 LABOUR:133 MODIFY BEARINGS FOR LARGE RAD. CRANK 120.00 LABOUR:140 A9 HOSE ADAPTOR FOR COOLING FAN SWITCH 45.00 LABOUR:145 S6L ENGINE MOUNT JAGUAR 70.00 LABOUR:146 S6R ENGINE MOUNT JAGUAR 70.00 LABOUR:147.1 A7 STEEL RADIUS ARM COLLAR 15.00 MITSUBISHI LABOUR:130 MITSUBISHI TRIGGER WHEEL 300.00 LABOUR:131 MODIFY WRC MITZ ALS VALVE 300.00 RS200 LABOUR:149 RS200 PIPE SET FOR PAS RACK RHD 240.00 LABOUR:150 RS200 STEERING RACK CONVERSION 720.00 LABOUR:158 MODIFY FLYWHEEL FOR 36-1 CRANK 420.00 LABOUR 179 ASSEMBLE XTRAC GEARBOX 960.00
RALLYCROSS LABOUR:048 STRIP - CLEAN - INSPECT - REBUILD RALLYCROSS ENGINE 3,000.00 LABOUR:048.2 BUILD LATEST SPEC RALLYCROSS ENGINE 3,600.00 LABOUR:075.1 MACHINE SPRING SEATS COSWORTH 120.00 LABOUR:075.3 SHIM UP VALVE SPRINGS COSWORTH 120.00 LABOUR:084.1 SHORTEN RALLYCROSS VALVES 16 OFF FOR RX CAMSHAFTS 60.00 LABOUR:086 PORT GROUP A CYLINDER HEAD COSWORTH RALLYCROSS; inc. reface valves, 1,440.00 cut seats & remove & refit valve guides. LABOUR:151 PULLEY FLANGE FOR 36:1 CRANK PULLEY 60.00 LABOUR:152.1 MODIFY CAM COVER FOR 4 COIL PER PLUG 60.00 LABOUR:152.2 MACHINE CAM COVER FOR BIG BREATHER HOLE 15.00 LABOUR:152.3 MODIFY CAM COVER FOR PHASE SENSOR 60.00 LABOUR:152.4 MACHINE CAM COVER FOR 1/8" FOR CRANK CASE PRESSURE 15.00 LABOUR:156 PECTEL ECU AFTERCARE 330.00 LABOUR:161 MAKE UP POWER STEERING PUMP SET UP 420.00 LABOUR:165 AEROQUIP FITTING & PIPE WORK FOR SWEDISH DRY SUMP & TURBO DRAIN 480.00 LABOUR:166 MANUFACTURE OIL PUMP BRACKET 160.00 LABOUR:168 MACHINE SET OF 4 SPARK PLUGS 30.00 LABOUR:170 MACHINE CAMSHAFT FOR TRIGGER 60.00 COSWORTH 200 BLOCK LABOUR:037 REMOVE & REFIT LINER & BORE 120.00 LABOUR:041 GROUP A MACHINE BLOCK & FIT NICKERSIL LINERS 780.00 LABOUR:041.1 REMOVE & REFIT NICKERSIL LINER 60.00 LABOUR:041.2 CONVERT BLOCK FROM DRY LINER TO WET LINERS 360.00 LABOUR:041.3 EXTRA 4 LONG STUD CONVERSION 120.00 LABOUR:041.5 MACHINE WATER PUMP TO CLEAR WET LINERS 45.00 LABOUR:041.6 MODIFY WATER PUMP FOR 10 LONG STUDS 45.00 LABOUR:042 GROUP A COOPERS RING CONVERSION 120.00 LABOUR:042.1 GROUP A - 10 LONG STUD CONVERSION 210.00 LABOUR:042.3 MODIFY BLOCK TO SUIT COMETIC COOPER GASKET 180.00 LABOUR:043 GROUP A - 6 LONG STUDDED CONVERSION 90.00 LABOUR:043.01 MACHINE OIL SQUIRT JETS FOR EECIV 90.00 LABOUR:043.02 GROUP A MACHINE ENGINE MOUNTS TO M10 120.00 LABOUR:043.03 GROUP A MACHINE SIDE OF BLOCK FOR OIL FEEDS 90.00 LABOUR:043.04 SECURE CORE PLUGS 4 OFF 60.00 LABOUR:043.05 MACHINE BREATHER HOLE & DRILL & TAP M4 HOLE 45.00 LABOUR:043.06 DRILL & TAP M4 FOR BREATHER POT 15.00 LABOUR:043.07 REMOVE LUMP SIDE OF BLOCK 15.00 LABOUR:043.08 MACHINE OF FUEL PUMP BOSS & TAP M8 & M10 90.00 LABOUR:043.09 1/2" BSP TAPPING 15.00 LABOUR:043.10 CHOP 3 LUGS OFF SIDE OF BLOCK 15.00
LABOUR:043.11 SUMP BOLTS MODS TO FIT XTRAC SUMP, DRILL & TAP M8 6 HOLES 60.00 LABOUR:043.12 MACHINE UP 3 OFF PLUGS FOR OIL FEED TO HEAD 30.00 LABOUR:043.13 DRILL WATERWAYS IN BLOCK 30.00 LABOUR:043.14 DRILL & TAP BLOCK FOR KNOCK SENSOR 15.00