Ball Valves Quality Valves at Low Cost
Table of Contents B Series, 2, 3 PC Ball Valves Part Numbering System...3 B0: 2 PC, 000 WOG, 36SS... 4 B02: 2 PC, 2000/0 WOG, 36SS... 4 B03: 2 PC, 000 WOG, 36SS Direct Mount... 5 B04: 3 PC, 000 WOG, 36SS, Screwed Ends... 5 B04S: 3 PC, 000 WOG, 36SS, Socket Weld Ends... 5 B05: 3 PC, 000 WOG, 36SS, Direct Mount, Screwed Ends... 6 B05S: 3 PC, 000 WOG, 36SS, Direct Mount, Socket Weld Ends... 6 B05TC: 3 PC, 000 WOG,36SS, Direct Mount, Tri-Clamp Ends... 6 B05TO: 3 PC, 000 WOG, 36SS, Direct Mount, Tube-Ends... 7 B06: PC, 2000 PSI, Carbon Steel/Barstock... 7 B07L: 3 PC, 000 WOG, 36SS, 3 way, L port... 8 B07T: 3 PC, 000 WOG, 36SS, 3 way, T-port... 8 B: 2 PC, 2000/0 WOG, Carbon Steel... 8 BT3/BT6: 3 PC, 3000/6000 PSI, Carbon Steel... 9 Z Series Floating Flanged Ball Valves Part Numbering System... 0 Z Series Pressure & Temperature Charts... 0 # RF Flanged ZF Full Port Direct Mount SS... ZF Full Port Carbon Steel & Low Temp... 2 ZR Reg Port Carbon Steel & Low Temp... 3 300# RF Flanged ZF3 Full Port Carbon Steel, Low Temp & SS... 4 ZR3 Reg Port Carbon Steel & Low Temp... 5 600# RF Flanged ZF6 Full Port Carbon Steel & Low Temp... 6 ZR6 Reg Port Carbon Steel & Low Temp... 7 T Series Flanged Trunnion Ball Valves Part Numbering System... 8 T Series Pressure & Temperature Charts... 8 T Series Trunnion Ball Valves Features & Specifications... 9 T Series General Dimensionsional Chart... 20 Additional Information Automation... 22 Terms and Conditions... 24 Sizes and Specifications shown are subject to change without notice. Page 2
B Series, 2, 3 PC Ball Valve Part Numbering System 2 = Valve Size 02 = /4 03 = 3/8 05 = /2 07 = 3/4 0 = 2 = -/4 5 = -/2 20 = 2 25 = 2-/2 30 = 3 40 = 4 2 = Valve Series B0: 2 PC, 000 WOG, 36SS B02: 2 PC, 2000/0 WOG, 36SS B03: 2 PC, 000 WOG, 36SS Direct Mount B04: 3 PC, 000 WOG, 36SS, Screwed Ends B04S: 3 PC, 000 WOG, 36SS, Socket Weld Ends B05: 3 PC, 000 WOG, 36SS, Direct Mount, Screwed Ends B05S: 3 PC, 000 WOG, 36SS, Direct Mount, Socket Weld Ends B05TC: 3 PC, 000 WOG,36SS, Direct Mount, Tri-Clamp Ends B05TO: 3 PC, 000 WOG, 36SS, Direct Mount, Tube-Ends B06: PC, 2000 PSI, Carbon Steel/Barstock B07L: 3 PC, 000 WOG, 36SS, 3 way, L port B07T: 3 PC, 000 WOG, 36SS, 3 way, T-port B: 2 PC, 2000/0 WOG, Carbon Steel BT3/BT6: 3 PC, 3000/6000 PSI, Carbon Steel Sizes and Specifications shown are subject to change without notice. Page 3
2-PC Full Port SS 000 PSI Ball Valve B0 No Parts Qty Material 0 Body ASTM-CF8M-A35 02 End ASTM-CF8M-A35 03 Ball ASTM-CF8M-A35 04 Ball Seat 2 5% R-PTFE 05 Joint Gasket PTFE 06 Stem AISI 36 07 Thrust Washer PTFE 08 Stem Packing 2 PTFE 09 Gland Nut 0 Handle Spring Washer 2 Stem Nut 3 Handle Sleeve Vinyl Grip Pressure rating: - 000 psi (69 Bar) WOG for /4 to 2 - Investment Cast Body & End - Full Port - FNPT threaded on both ends - Material: ASTM A35-CF8M - NACE MR075 - Locking Handle Size /4 3/8 /2 3/4 -/4 dia (mm).6 2.5 5 20 25 32 L 60 65 80 92 H 48 48 52 6 65 79 W 9 9 9 54 S 6.5 6.5 6.5 20 23.5 23.5 S 0.2 0.2 0.2 3.5 6 6 X 5 5 5 6.5 8 8 N 2.5 2.5 2.5 2 22.5 23.5 P 28.5 28.5 28.5 34.8 34.8 38. BL 5/6 5/6 5/6 3/8 7/6 7/6 Torque (in-lbs) 35 35 47 64 90 7 CV Factor 7 7 5 45 65 25 Wt Kwg 0.2 0.22 0.29 0.42 0.7.06 4 Lock Device AISI 430 -/2 38 05 83 54 25.5 7 9 23.5 38. /2 56 75.68 2 25 97 92 25.5 7 9 23.5 38. /2 27 380 2.7 2-PC Full Port SS 2000 PSI Ball Valve B02 No Parts Qty Material 0 Body ASTM-CF8M-A35 02 End ASTM-CF8M-A35 03 Ball ASTM-CF8M-A35 04 Ball Seat 2 5% R-PTFE 05 Joint Gasket PTFE 06 Stem AISI 36 07 Thrust Washer PTFE 08 Stem Packing 2 PTFE 09 Gland Nut 0 Handle Pressure rating: - 2000 psi (37.8 Bar) WOG for /4 to 2-0 psi (89.6 Bar) WOG for 3 - Investment Cast Body and Ends / Full Port - FNPT threaded on both ends - Locking Handle - Material: ASTM A35-CF8M - NACE MR075 *Note: available in Carbon Steel as model B on page 8 Size /4 3/8 /2 3/4 -/4 -/2 dia (mm).6 2.7 5 20 25 32 38 L H W X BL 44.5 44.5 57 65 76 87.5 02 5 5 53 59.5 73 79 90.5 95 95 95 0 35 35 65 5 5 5 6.5 8 8 9 5/6 5/6 5/6 3/8 7/6 7/6 /2 CV Factor 6.6 7.9.2 2 35 57 80 Torque in-lb 35 35 47 64 90 7 56 Wt Kg 0.94 0.205 0.285 0.456 0.764.63.870 2 3 4 Spring Washer Stem Nut Handle Sleeve Lock Device Vinyl Grip 2 23 98.8 65 9 /2 48 27 3.26 3 80 84 42.5 25 2 3/4 45 65 9.79 Sizes and Specifications shown are subject to change without notice. Page 4
2-PC Full Port SS Ball Valve - Direct Mount* B03 * See Page 22 for Actuation No Parts Material 0 Body ASTM-A35 Gr. CF8M 02 Ends ASTM-A35 Gr. CF8M 03 Ball ASTM-A35 Gr. CF8M 04 Stem 36SS 05 Ball Seat 5% RTFE 06 Gasket 5% RTFE 07 Stem Packing 5% RTFE 08 Thrust Washer 5% RTFE 09 Stem Packing 304SS 0 Belleville Washer SUS 304-USP Thrust Washer PTFE + 25% Carbon Pressure rating: - 000 psi (69 Bar) WOG for /4 to 2 - Investment Cast Body and Ends / Full port - Direct Mounting Pad for ISO Std 52 - FNPT threaded on both ends - Material: ASTM A35-CF8M (36SS) - NACE MR075 Size /2 3/4 -/2 2 dia (mm) 5 20 25 38 L F M ISO 52 Torque in-lbs D H D S A Cv 65.3 6 7.5 42 F04 F05 85 9 72.85 2 8.5 36.95 5 77.3 7.5 9.5 70 F05 F07 0 9 8.8 2 8.5 45 45 88.7 7.5 9.5 70 F05 F07 80 90.45 36.4 53.45 65 09 7.5 9.5 70 F05 F07 35 4 4.7 97.9 4 74.75 75 25.3 9.5 70 02 F07 F0 4 4 24.0 97.9 3.7 83.5 380 Wt Kg 0.46 0.8 0.96 2.3 2.3 2 3 4 5 6 7 O-Ring Locking Washer Stem Nut Handle Handle Nut Handle Cover Viton 304SS 304SS 304SS 304SS Vinyl Grip 3-PC Full Port SS 000 PSI Ball Valve B04/B04S No Parts Qty Material 0 Body ASTM-CF8M-A35 02 End ASTM-CF8M-A35 03 Ball ASTM-CF8M-A35 04 Ball Seat 2 5% RTFE 05 Joint Gasket 5% RTFE 06 Stem AISI 36 07 Thrust Washer PTFE 08 Stem Packing 2 PTFE 09 Gland Nut 0 Handle Stem Washer 2 Stem Nut 3 Handle Sleeve Vinyl Grip 4 Lock Device 5 Bolt 4-6 Pressure rating: - 000 psi (69 Bar) WOG for /4 to 4 - Investment Cast Body & Ends - Full port - FNPT threaded on both ends for B04 - Socket Weld on both ends for B04S - Locking Handle - Material: ASTM A35-CF8M (36SS) Size dia (mm) L H W B D S /4 3/8 /2 3/4 -/4 -/2 2 2-/2 3 4.6 2.7 5 20 25 32 38 65 80 00 54 54 6.5 7 83.5 97 0.5 29 7.5 200 252 5 5 55 58.5 73 78.5 90.5 99 27 36 72 84 84 84 0 35 35 65 65 25 25 325 2 2.5 5.8 20.9 26.6 35.05 40.9 52.5 69 82 06 8 8 22 28 34 44 6.5 76 90 5 4. 7.6 2.7 27.2 33.9 42.6 48.7 6. 76.9 89.8 5.4 Cv Factor 0 0 26 68 20 70 360 900 2 Wt Kg 0.34 0.34 0.46 0.62.96.49 2 3.2 6.5 0.4 20.2 6 7 Spring Washer Hex Nut 4-2 4-2 Sizes and Specifications shown are subject to change without notice. Page 5
3-PC Full Port SS Ball Valve - Direct Mount* B05* Threaded (B05), Socket Weld (B05S), and Tri-Clamp (B05TC) ends * See Page 22 for Actuation B05/B05S B05TC No Parts Qty Material Pressure rating: - 000 psi (69 Bar) WOG for /4 to 4 High Cycle, Live Loaded, Triple Stem Seal comprising of: - Carbon Filled PTFE Wedge Ring Thrust Washer and Viton O-Ring - 5% RTFE Chevron packing - Live loaded Belleville Washers - Packing Nut Mechanically Locked to Stem - Investment Cast Body & Ends - Full port - Direct Mounting Pad for ISO Std 52 - FNPT threaded on both ends on B05 - Socket weld ends on B05S - Material: ASTM A35-CF8M (36SS) and 36LSS ends on Socket Weld 0 02 03 04 05 06 07 08 09 0 2 3 4 5 6 7 8 9 20 Body Ends Ball Stem Seat Stem Packing Washer Thrust Washer Belleville Washer Stem Nut Bolts Spring Washer Bolts Nuts Stem Ring O-Ring Stopper Washer Square Handle Handle Nut Stopper Pin 2 2 4-6 4-6 4-6 ASTM-A35 Gr. CF8M ASTM-A35 Gr. CF8M *CF3M for SW ASTM-A35 Gr. CF8M SS 36 5% RTFE 25% CTFE PTFE +25% Carbon SUS 304-CSP PTFE +25% Carbon VITON 2 Handle Sleeve Vinyl Size d L F M ISO 52 Torque in-lbs D H D S A Cv Wt Kg /2 3/4 -/2 2 3 4 5 20 25 38 80 00 63.5 72.5 8 08 2.5 90 225 6 7.5 7.5 7.5 9.5 7.5 9.5 9.5 9.5 4.3 4.3 42 F04 F05 F05 F05 70 F07 02 F0 02 F0 F05 70 F07 70 F07 70 F07 02 F0 25 F2 25 F2 85 0 80 35 4 680 90 9 9 4 4 7 22 72.95 80.8 90.45 5.25 24.0 208.5 26.7 2 2 36 97.9 97.9 264 325 8.5 8.5.4 4 3.7 8 23 36.95 45 53.45 74.75 83.5 8.25 53.75 26 68 70 360 900 2 0.6 0.7.03 2.5 3.4.2 22 Sizes and Specifications shown are subject to change without notice. Page 6
3-PC Full Port SS Ball Valve - Direct Mount* * See page 22 for Actuation Pressure rating: - 000 psi (69 Bar) - WOG for /2 to 4 High Cycle, Live Loaded, Triple Stem Seal comprising of: - Carbon Filled PTFE Wedge Ring Thrust Washer and Viton O-Ring - 5% RTFE Chevron packing - Live loaded Belleville Washers - Packing Nut Mechanically Locked to Stem - Investment Cast Body & Ends - Full port - Direct Mounting Pad for ISO Std 52 - Tube Ends - Material: ASTM A35-CF8M (36SS) Size dia ISO Torque D L H mm M B B2 K D E D2 H A C C2 52 in-lbs X A L /2 5 F03-F04 9.5 89 37.0 9 36 42 9 25.4 43 2.7 26 8 6 6 90 5.5 42 37 3/4 20 F03-F04 5.9 0 47.0 9 36 42 9 25.4 43 9. 26 2 6 6 00 20.6 44 47 25 F04-F05 22.2 4 57.2 42.4 60 25.4 34 25 6 8 40 29.0 52 68 -/2 40 F05-F07 35.0 40 78.2 4 70 4.4 87 38.2 43 28 8 0 240 39.0 5 86 2 F05-F07 47.6 56 86.2 4 70 4 63.8 87.8 43 25 8 0 480 42.0 58.5 223 2-/2 65 F07-F0 60.3 97 09.2 7 70 02 7 77.6 30 63.5 53 35 0 2 6 48.0 / / 3 80 F07-F0 73.0 229 7.7 7 70 02 7 9.0 30 76.2 53 43 0 2 48.7 / / 4 00 F0-F2 97.4 24 4.2 22 02 25 22 9.0 400 00.6 56 37 2 4 400 34.0 / / -PC Reg Port Carbon Steel 2000 PSI Ball Valve No 0 02 03 04 05 06 07 08 09 0 2 3 4 5 6 7 8 9 20 2 B05TO Parts Material Body /36/36L Ends /36/36L Ball /36/36L Seat PTFE/TFM 600 Gasket PTFE Thrust Packing PTFE Stem Packing PTFE Ring Belleville Washer Stem Nut Lock Washer Ring Handle Nut Stop Pin Handle Handle Sleeve Plastic Stem AISI 36 Spring Washer Bolt Nut Bolt O-Ring Viton B06 No Parts Material 0 Body A08 02 Insert A08 03 Ball AISI 36 04 Seat PTFE+5% G/F 05 Stem AISI36 06 Thrust Washer PTFE 07 Stem Seal PTFE 08 Handle 09 Handle Sleeve Vinyl Grip 0 Nut 304 SS Pressure rating: 2000 psi (38 Bar) 2 Washer Spring Washer WCB 304 SS - NACE MR075 - FNPT threaded on both ends - Body material: ASTM A05N Carbon Steel Size A B C D E F Wt (kg) Cv /4 6 29.5 4.3 5 2 24. 0.2.5 3/8 79 34.5 44 7.2 23 26.4 0.22 3.5 /2 08 63 57.2 9.0 29 33.3 0.29 5.7 3/4 0 65 65. 2.5 35 40.3 0.42 0 22 68 7 5 4 47.2 0.7 6 -/4 45 79.5 92. 20 55 63.4.06 25 -/2 48 84 98.4 25 57 65.7.68 40 2 48 92.5 4.3 32 73.5 84.7 2.7 62 Sizes and Specifications shown are subject to change without notice. Page 7
3-way Reg. Port SS Ball Valve - Direct Mount* B07L/T * See page 22 for Actuation No Parts Material 0 Body ASTM-A35 Gr. CF8M 02 Ends ASTM-A35 Gr. CF8M 03 Seat 5% RTFE 04 Ball ASTM-A35 Gr. CF8M 05 Stem SS 36 5 4 06 07 Gasket Thrust Washer 5% RTFE PTFE + 25% Carbon 08 Stem Packing 5% RTFE 09 Gland 0 Belleville Washer SUS 304-CSP Pressure rating: 000 psi (69 Bar) WOG for /4 to 2 High Cycle, Live Loaded, Triple Stem Seal comprising of: - Carbon Filled PTFE Wedge Ring Thrust Washer - Viton O-Ring - 5% RTFE Chevron packing - Live loaded Belleville Washers - Packing Nut Mechanically Locked to Stem - Anti-static device - L-port & T-port - FNPT end connections - Locking Handle - Material: ASTM A35 GR.CF8M (36SS) 3 2 0 9 8 7 6 5 4 3 2 7 8 9 6 2 3 4 5 6 7 8 9 Stem Nut Handle Handle Nut End Cap Gasket Handle Sleeve Locking Washer Thrust Washer O-Ring ASTM-A35 Gr. CF8m 5% RTFE Vinyl Grip SUS 304-CSP PTFE + 25% Carbon Viton 2-PC Full Port Carbon Steel Ball Valve B Pressure rating: - 2000 psi (37.8 Bar) WOG for /4 to 2-0 psi (03.4 Bar) WOG for 3 - Full Port - FNPT threaded on both ends - Locking Handle - Carbon Steel Body and Ends - Material: ASTM A26-WCB - NACE MR075 *Note: available in Stainless Steel as model B02 on page 4 Sizes and Specifications shown are subject to change without notice. Page 8
3-PC Threaded Body 3000/6000 PSI Ball Valve BT3/BT6 Pressure rating: 3000 psi (BT3) / 6000 psi (BT6) Specifications: Standard - Designed to ASME B6.34 - Available in full port & reg port - NPT & SW to ASME B6. - Forged Steel Body - Tested to API 598 - Locking Lever - API 607 firesafe - Blowout proof stem -NACE MR075 - Antistatic device -CRN - Mounting pad Sizes and Specifications shown are subject to change without notice. Page 9
Z Series Floating Flanged Ball Valves Part Numbering System 2 3 4 5 6 7 8 9 = Code & Class ZR = Reduced port class ZR3 = Reduced port class 300 ZR6 = Reduced port class 600 ZF = Full port class ZF3 = Full port class 300 ZF6 = Full port class 600 2 = Size 0 = /2 075 = 3/4 00 = = -/2 002 = 2 2 = 2-/2 003 = 3 004 = 4 006 = 6 008 = 8 3 = Type A = Floating ball split body B = Floating ball unibody 4 = Body Material = ASTM A26 WCB 2 = ASTM A352 LCC 3 = ASTM A35 CF8M 4 = A05N 5 = A3 LF2 5 = End Connection F = Raised face flanged * R = Ring joint flanged ends B = Butt-welded ends 6 = Trim Material = Body + 3ENC 2 = 304SS 3 = 36SS * 7 = Seat material P = PTFE R = RTFE * N = Nylon K = PEEK D = Devlon 8 = Operator H = Handle/Lever G = Gear Operator B = Bare Stem 9 = Special Requirements 00 = Standard Requirement * Denotes standard stock trim Z Series Pressure & Temperature Charts # & 300# 600# Sizes and Specifications shown are subject to change without notice. Page 0
# Full Port Direct Mount SS ZF * See page 22 for Actuation - Full bore, 2 piece body floating ball - ISO Mounting Pad, direct mounting to actuator - Cavity relieving seats, anti-static device - Lever operated Specifications: - Designed according to ASME/ANSI Class - B6.34 - Face to Face per ASME/ANSI B6.0 Long Pattern - Flanges designed per ASME/ANSI B6.5 - NACE MR075 - Design Standard per API 608 - Markings per MSS-SP25 - Pressure Test per API 598 Sizes and Specifications shown are subject to change without notice. Page
# Full Port Carbon Steel & Low Temp ZF - Full bore, 2 piece body floating ball - ISO Mounting Pad - Cavity relieving seats, anti-static device - Lever operated 2-6, Gear operated 8 Specifications: - Fire-safe to API-607, latest Ed. - Designed to ASME/ANSI Class -B6.34 - Face to Face to ASME/ANSI B6.0 Long Pattern - Flanges to ASME/ANSI B6.5 - NACE MR075 - Design Standard per API 608 - Markings per MSS-SP25 - Pressure Test per API 598 L E V E R G E A R Sizes and Specifications shown are subject to change without notice. Page 2
# Reg. Port Carbon Steel & Low Temp ZR - Reduced bore, piece unibody floating ball - ISO Mounting Pad - Cavity relieving seats, anti-static device - Lever operated Specifications: - Fire-safe to API-607, latest Ed. - Designed to ASME/ANSI Class -B6.34 - Face to Face to ASME/ANSI B6.0 Short Pattern - NACE MR075 - Design Standard per API 608 - Markings per MSS-SP25 - Pressure Test per API 598 O-Ring Sizes and Specifications shown are subject to change without notice. Page 3
300# Full Port Carbon Steel, Low Temp & SS ZF3 - Full bore, 2 piece body floating ball - ISO Mounting Pad - Cavity relieving seats, anti-static device - Lever operated 2-6, Gear operated 8 Specifications: - Fire-safe to API-607, latest Ed. - Designed to ASME/ANSI Class 300-B6.34 - Face to Face to ASME/ANSI B6.0 Long Pattern - Flanges designed per ASME/ANSI B6.5 - NACE MR075 - Design Standard per API 608 - Markings per MSS-SP25 - Pressure Test per API 598 L E V E R Gland G E A R Antistatic Sizes and Specifications shown are subject to change without notice. Page 4
300# Reg. Port Carbon Steel & Low Temp ZR3 - Reduced bore, piece unibody floating ball - ISO Mounting Pad - Cavity relieving seats, anti-static device - Lever operated Specifications: - Fire-safe to API-607, latest Ed. - Designed according to ASME/ANSI Class 300 - B6.34 - Face to Face per ASME/ANSI B6.0 Short Pattern - NACE MR075 - Design Standard per API 608 - Markings per MSS-SP25 - Pressure Test per API 598 Sizes and Specifications shown are subject to change without notice. Page 5
600# Full Port Carbon Steel & Low Temp ZF6 - Full bore, 2 piece split body floating ball - ISO Mounting Pad - Anti-static device - Lever operated Specifications: - Fire-safe to API-607, latest Ed. - Designed to ASME/ANSI Class 600 - B6.34 - Face to Face to ASME/ANSI B6.0 Long Pattern - Flanges to ASME/ANSI B6.5 - NACE MR075 - Design Standard per API 608 - Markings per MSS-SP25 - Pressure Test per API 598 Antistatic Sizes and Specifications shown are subject to change without notice. Page 6
600# Reg. Port Carbon Steel & Low Temp ZR6 - Reduced bore, 2 piece split body floating ball - ISO Mounting Pad - Anti-static device - Lever operated 2-4, Gear operated 6 Specifications: - Fire-safe to API-607, latest Ed. - Designed to ASME/ANSI Class 600 - B6.34 - Face to Face to ASME/ANSI B6.0 Long Pattern - Flanges to ASME/ANSI B6.5 - NACE MR075 - Design Standard per API 608 - Markings per MSS-SP25 - Pressure Test per API 598 L E V E R Antistatic G E A R Sizes and Specifications shown are subject to change without notice. Page 7
T Series Flanged Trunnion Ball Valve Part Numbering System 2 3 4 5 6 7 8 9 = Port & Class TR = Reduced port class TR3 = Reduced port class 300 TR6 = Reduced port class 600 TR9 = Reduced port class 900 TR5 = Reduced port class 0 TR25 = Reduced port class 20 TF = Full port class TF3 = Full port class 300 TF6 = Full port class 600 TF9 = Full port class 900 TF5 = Full port class 0 TF25 = Full port class 20 2 = Size 002 = 2 003 = 3 004 = 4 006 = 6 008 = 8 00 = 0 02 = 2 04 = 4 06 = 6 08 = 8 020 = 20 024 = 24 026 = 26 028 = 28 030 = 30 032 = 32 034 = 34 036 = 36 040 = 40 042 = 42 3 = Type T = 3 Piece Split Body S = 2 Piece Split Body W = Welded Body 4 = Body Material = ASTM A26 WCB (-29C) 2 = ASTM A352 LCC (-46C) 3 = ASTM A35 CF8M (-96C) 4 = ASTM A05N (-29C) 5 = ASTM A3 LF2 (-46C) 6 = ASTM 82 F36 (-96C) 7 = DUPLEX 22CR 5 = End Connection F = Flanged Raised Face J = Flanged RTJ B = Butt Weld End G = Weld X RF H = Weld X RTJ P = Weld W/PUPS X = GRAYLOC 6 = Trim Material = Body + 3ENC 2 = 304SS 3 = 36SS 4 = 40SS 5 = DUPLEX 22CR 7 = Seat Material P = PTFE R = RTFE N = Nylon K = PEEK D = Devlon M = Metal x Metal 8 = Operator L = Handle/Lever G = Gear Operator B = Bare Stem C = Chain Wheel 9 = Special Requirements 00 = Standard Requirement T Series Pressure & Temperature Charts Sizes and Specifications shown are subject to change without notice. Page 8
T-Series Trunnion Ball Valves Compliance and Specifications ISO 433:2007 / API 6D ISO 900-2008 Registered Quality System API 608 / API 598 Firesafe to API 607 ASME B6.34, B6.5, B6.0 CSA Z245.5 Steel Valves NACE MR075 / ISO 556 Compliance Features Designs Available - Two piece cast design or three piece forged design available. Double Block & Bleed - Independent spring loaded upstream and downstream seats and body bleed ensure suitability for use in double block & bleed service. Antistatic Design - Antistatic design to ensure electrical continuity between stem, ball and body. Emergency Seat and Stem Seal Injection (varies on size) - In case of unforeseen seal damage or valve leakage while in service, injection facilities are available on the valves when a critical seal is demanded and there is no time to service or shut down the facility. Automatic Body Cavity Relief - Trunnion Mounted Ball Valves are protected from thermal expansion and body cavity over pressurization due to spring loaded seats which automatically relieve pressure to the down stream side of the body cavity. In addition, all valves come with a manual safe relieving bleed valve. Seat Design - The seats are free floating along the valve axis. At low pressure, ball and seat sealing is maintained by pre-loaded seat springs. High pressure sealing is maintained by the line pressure acting on the differential area of the seats. Other materials available upon request Materials shown are general materials of construction for 2 piece or 3 piece Trunnion Ball Valves We reserve the right to substitute materials listed above with alternate approved material for specific service conditions * Standard Inventory Trim ** Indicated parts included in Minor Repair Kit Sizes and Specifications shown are subject to change without notice. Page 9
T Series Trunnion General Dimensional Data Sizes and Specifications shown are subject to change without notice. Page 20
T Series General Trunnion Dimensional Data Sizes and Specifications shown are subject to change without notice. Page 2
Actuation Selection Chart For ISO Direct mount Ball Valves Only (B03, B05/5S/5TC/5T0, B07L/T & ZF SS Only)* * Actuator sized for liquid service up to 0 psig differential line pressure using 80 psig instrument air. ** Actuator sizing torques up to 0 psig DP, Water -.0, Oil - 0.8, Gas Wet (Steam) -.0, Gas Dry -.3. *** Add 20% on torque values for 3-way B07 series valve. **** For high or low temperature applications consult supplier for special seal kits. Sizes and Specifications shown are subject to change without notice. Page 22
SPNII Actuator Information Sizes and Specifications shown are subject to change without notice. Page 23
ValvSource Equipment Limited (herein referred to as ValvSource ) is pleased to advise its customers ( Purchaser ) of Flow+ brand products ( Product or Products ) that the manufacturer ( Manufacturer ) warrants its Products against defects in material and workmanship ( Defects ) for a period of eighteen (8) months from shipment or one () year from installation ( Warranty Period ). Purchaser acknowledges that the Products are provided to the Purchaser subject only to the limited warranties provided by the manufacturer of the Products and are subject to all of the conditions, limitations and exclusions set out therein, all of which are hereby accepted by the Purchaser. Extent of Remedy. Where ValvSource is advised in writing of Defects within the Warranty Period, Manufacturer will be deemed to have received notice of the defect and Manufacturer will, at its option, replace or recondition the Product without charge. Where a replacement or reconditioned Product is provided during the Warranty Period, that Product shall be subject to the same warranty for the unexpired portion of the original Warranty Period. This remedy shall constitute the exclusive remedy available to Customers for defective Products. Limitations. Neither ValvSource nor Manufacturer shall be liable for any incidental, consequential or other damages, costs or economic losses, including, without limitation, any resulting from labour charges, delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions, chemicals, acts of God, or circumstances that are not controllable or reasonably foreseeable by either Manufacturer or ValvSource. Invalidation of Warranty. The warranty exclusions include, without limitation, (I) any defects caused by faulty installation performed by Purchaser or third parties, (II) any damage caused by the contractors or tradesman of the Purchaser, (III) any damage caused by improper use or misuse, including exposure to excessive temperatures, moisture or cleaning agents and solvents and (IV) any damage caused during transportation or improper storage. All claims received by ValvSource beyond the Warranty Period are invalid and shall not be accepted. Disclaimer. Except for the express written warranty contained herein, neither Manufacturer nor ValvSource makes any other warranty, condition, guarantee or indemnity, express or implied, statutory or otherwise, regarding the Products INCLUDING WITHOUT LIMITATION, TO THE EXTENT PERMITTED BY LAW, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. All other warranties, conditions guarantees and indemnities regarding any Products are hereby disclaimed, excluded and overridden. Further Warranty Information. For complete detailed terms of sale and warranty information on all products distributed by ValvSource, including brands from third party manufacturers distributed by ValvSource, please visit: http://www.valvsource.com. Please refer to terms and conditions section. Flow+ is a registered trademark. Contact Information Your local Sales Representative: