UTION! IS YOUR VLVE OPEN OR LOSE? MOEL 9-LP POSITION INITOR Know the status of your buried service valve with the 9-LP from Valcom 9-LP FETURES: Eliminates the need for Vs or risers. Wedgelock system holds unit securely in place. Eliminates the need for precise height adjustment of stems. Fits any valve box with a -/" I or any -/" valve box with adjustable sleeve. an be used with locking covers, unit will slide past stop blocks. an be removed without digging up pavement. Gear ratios to 900: standard one low price. Higher ratios avail. rop in installation, no accessories required. Ready to install. Manufactured from corrosion resistant materials. Sealed against dust and dirt, suitable for inground installation. Fits into existing standpipes. ME IN THE US "INIO" is a registered trademark of the VLOM div of TRI 0 website www.tooling-research.com email info@tooling-research.com
TURN RTIO WINOW RTIO TO E SPEIFIE Y USTOMER UP TO 000: MX INIO MOEL 9-LP POSITION INITOR G Y VLOM IV OF TRI WLPOLE, M 00 0 PPROXIMTELY 9.00 ISTNE FROM INSIE OF NUT POKET TO TOP OF " WW NUT. TURN IRETION OPTION LOSE-OPEN OR OPEN-LOSE " WW NUT INLUE " WW NUT POKET INLUE TOOLING RESERH IN. IMON ST. WLPOLE, M 00 0 90 THE INFORMTION ONTINE IN THIS RWING IS THE SOLE PROPERTY OF TOOLING RESERH, IN. NY REPROUTION OF THIS RWING IN WHOLE OR IN PRT WITH OUT THE RESERH, IN, IS PROHIITE IMENSIONS RE IN INHES TOLERNES RE: FRTIONS EIMLS NGLES / XX.00 XXX.00 XXXX.000 SPEIFIE REMOVE LL URRS N SHRP EGES THIR NGLE PROJETION MTERIL O NOT SLE RWING RWN QTY PER SSY SLE POSITION INITOR 9-LP SHEET _ OF_
INIO MOEL 9-LP POSITION INITOR G Y VLOM IV OF TRI WLPOLE, M 00 0 LERNE FOR TS IN V LLOWS 9-LP TO ENTER PIPE S REQ' TO ENGGE STEM EXTENSION WEGE LOK LMPS PROVIE SEURE POSITIONING INSIE V LERNE ON TOP FLNGE LLOWS UNIT TO SLIE INTO NY " I PIPE-N E USE WITH NY STNR OR LOKING V OVERS-ELIMINTE THE NEE FOR V RISER TOOLING RESERH IN. IMON ST. WLPOLE, M 00 0 90 THE INFORMTION ONTINE IN THIS RWING IS THE SOLE PROPERTY OF TOOLING RESERH, IN. NY REPROUTION OF THIS RWING IN WHOLE OR IN PRT WITH OUT THE RESERH, IN, IS PROHIITE IMENSIONS RE IN INHES TOLERNES RE: FRTIONS EIMLS NGLES / XX.00 XXX.00 XXXX.000 SPEIFIE REMOVE LL URRS N SHRP EGES THIR NGLE PROJETION MTERIL O NOT SLE RWING RWN QTY PER SSY SLE POSITION INITOR 9-LP SHEET _ OF_
NUMER OF TURNS= GER RTIO SPEIFY FR0M TO 900 TO SPEIFY OPEN W OR W I = STNPIPE I OR INH IRLE ONE # OF TURNS W OR W # OF UNITS FILL IN REQUIRE INFORMTION N FX K TO VLOM div of TRI 0 0 OR EMIL TO info@tooling-research.com TOOLING RESERH IN. IMON ST. WLPOLE, M 00 THE INFORMTION ONTINE IN THIS RWING IS THE SOLE PROPERTY OF TOOLING RESERH, IN. NY REPROUTION OF THIS RWING IN WHOLE OR IN PRT WITH OUT THE RESERH, IN, IS PROHIITE IMENSIONS RE IN INHES TOLERNES RE: FRTIONS EIMLS NGLES / XX.00 XXX.00 XXXX.000 0 90 SPEIFIE REMOVE LL URRS N SHRP EGES THIR NGLE PROJETION MTERIL O NOT SLE RWING RWN QTY PER SSY 0--00 SLE POSITION INITOR SERIES 9-LP 9-LP SHEET _ OF_
Installation of 9-LP low profile position indicator. 9-LP is designed to pass beyond locking hubs cast into standpipes and sit at any predetermined level within the pipe. Note: Leave tape in place on Position indicator when installing for easier installation. Insert position indicator into any standpipe/ valve box until it engages WW drive nut located on end of stem extension. Insure that the arrow on the position indicator and the valve position coincide. IE if the valve is closed the position indicator arrow should be aligned with the black arrow on the closed side and vice versa. Once located in position tighten two locking screws located at 0 degrees from each other on the top of the indicator using a long handled / llen wrench. Preferably a ball driver type, but standard end will work. Tightening these screws will draw the two corresponding wedges between the indicator and the pipe wall providing a solid seat for the position indicator. o not over tighten. Install standard locking or non locking cover as required. The 9-LP position indicator is designed to allow installation in any standpipe without the necessity for a V. It can also be removed if required, and because of it s ability to fit entirely inside the pipe it eliminates the necessity for precise calculations of stem extension lengths. Final note: It may be necessary in some instances to remove excess slag in some standpipes in order to allow the indicator to seat properly.