Fire Fighting Reels HANNAY REELS Hannay booster and large-diameter hose reels give you: Faster clean up Preconnect or storage No draining, stacking, or dragging All sizes and capacities Efficient use of vehicle space Increased hose capacity H-9407-F Revision 6
INTRODUCTION It s easier to handle hose from booster to large diameter hose when Hannay Reels are lending a hand. Pumper with six reel units 1" booster hose to 4"LD collapsible hose. Fire fighters around the world depend on Hannay Reels. For decades, Hannay Reels has set the standard of quality and reliability for hose reels in the fire fighting industry. In supplying both apparatus manufacturers and after-market fire departments worldwide, Hannay has consistently serviced the needs of the industry. With Hannay Reels, there s no draining, stacking, or dragging. Plus, fire fighters appreciate quick attack and fast pick-up. Through research and development of internationally recognized standard models, to custom one-of-a-kind applications, Hannay continues to meet the specific needs of the vehicle or fire department. Our fire fighting reels come in all sizes and capacities and make efficient use of vehicle space. Numerous options and configurations are readily available to meet your needs. Attention Truck Committees and Specifiers of Fire Apparatus Products shown and described in this catalog are suggested models for broad use applications throughout the fire fighting industry. All our components are designed for multiple configurations to fit all your applications and space requirements. Therefore, all reel models can be adjusted dimensionally to fit your specific needs. For special requirements, contact your Hannay dealer or call our inside sales group. To order any Hannay Reel in this brochure, use the specifications listed here in conjunction with our Ordering Guide & Accessory Catalog.
Specifying Location of Components Optional Location of Components: Location of the inlet, outlet riser and rewind mechanism can be varied to meet your requirements and must be specified on your order. The drawings Right Top Rewind (RT) reels have the inlet, outlet riser and rewind mechanism on the operator s right. Hose unwinds from the top of the reel. Right Bottom Rewind (RB) reels have the inlet, outlet riser and rewind mechanism on the operator s right. Hose unwinds from the bottom of the reel. Note: Use position initials as suffix after model number, ie: EF32-23-24-RT Optional Motor Locations Electric rewind motors can be installed in any of the positions shown in these drawings. The Bottom Rear position is standard. The motor below show the component locations. Unless otherwise specified, most reels will be shipped as Right Top Rewind with the inlet, outlet riser and rewind mechanism on the operator s right. Left Top Rewind (LT) reels have the inlet, outlet riser and rewind mechanism on the operator s left. Hose unwinds from the top of the reel. Left Bottom Rewind (LB) reels have the inlet, outlet riser and rewind mechanism on the operator s left. Hose unwinds from the bottom of the reel. Bottom Rear Bottom Front Elevated 2 o clock Elevated 10 o clock (Standard) is installed inside the frame on Model ESF reels, which are designed for installation in restricted space. HOW TO SPECIFY HANNAY REELS Optional Auxiliary Rewind Positions Horizontal ring and pinion gear crank rewind mechanism is the standard configuration. Optional positions include vertical and 30 above centerline, as shown in these drawings. Both are available at extra cost and must be specified. Horizontal Vertical 30 Angle (Standard) Optional Roller Positions Optional roller assembly mounting kits, up to 2 of either can be mounted per reel. Consult factory, and indicate installation location front or rear of reel. High Mount Low Mount 1
Series F4000 Compact reels for booster hose. To handle single 3/4" I.D. or 1" I.D. hose. Series F4000 Standard Configuration Shown Compact reels for use in restricted spaces or on slide-on units. Also for use in brush and forest fire fighting vehicles. Rewind: Choose direct crank rewind (removable) or chain and sprocket drive powered by electric, hydraulic or compressed air motor. Crank is not supplied on power rewind models but is available at extra cost when specified. Brakes & Locks: Reels with direct crank rewind only are supplied with a spring tension brake, other brakes may be specified. (See Ordering Guide & Accessory Catalog.) Inlet: Standard inlet is 90-degree ball bearing swivel joint with 1" female NPT threads. Outlet: Standard outlet is 1" male NST threads (1.375" x 8 threads per inch). Other sizes and/or threads can be furnished and must be specified. Standard inlet, outlet riser and hub assembly are steel. These components can be supplied in stainless steel, at extra cost, to meet special product handling requirements. Optional Rollers: Rollers may be purchased as accessory items. Specify roller position when ordering. Mounting brackets are necessary. (See Ordering Guide & Accessory Catalog.) Operating Pressures & Temperatures: These reels operate at pressures to 1000 psi (69 bar) and handle product temperatures from 80º F to +185º F ( 62º C to+85º C). Reels to operate at other pressures and temperatures can be furnished at extra cost. CAUTION: F4000 series reels NOT recommended for use with Niedner Reeltex hose. 2
Series F4000 Specifications Dimensions and capacities E G 18.12" 460 B C 8" 203 H 9.88" 251 Y 10" 254 X D 14.5" 368 F4000 NOTICE: A FLEXIBLE CONNECTOR MUST BE USED BETWEEN THE INLET PIPE AND THE INLET SWIVEL JOINT. Be sure to check dimensions and weights prior to ordering. To receive a detailed parts breakdown drawing for Series F4000, request ISO 68. Hose Capacity of Reel Model Reel Dimensions Approx. Weight Number inches Crank Rewind mm See Note 2 feet lb. m NOTE 1 inch = 25.4 mm x, y indicate mounting holes kg. I.D. (in) 3/4" 1" E F I.D. (mm) 19 25 For power rewind ELEC ELEC O.D. (in) 1-9/32" 1-9/16" see Note 4 A B E AIR F AIR X NET SHIP O.D. (mm) 33 40 CRANK HYD CRANK HYD 100 50 F4024-17-18 21 16 16.5 19 32.62 27 19.5 46 56* 30 15 533 406 419 483 829 686 495 21 25 200 100 F4038-17-18 35 30 16.5 19 46.62 41 33.5 70 112 61 30 889 762 419 483 1184 1041 851 32 51 F A Specifications subject to change. Notes: 1. Upon request, reels can be supplied with drum lengths other than shown and with disc sizes in other diameters. 2. Weights shown in chart are for crank rewind models. Add these amounts for power rewind models. Net (lbs.) Ship (lbs.) Net (kg.) Ship (kg.) Electric 18 18 8.2 8.2 Hydraulic 15 15 6.8 6.8 Air 15 15 6.8 6.8 3. Dimension F is the overall length of standard model reels. On crank rewind models, the dimension shown is with the crank in rewind position. Reels require 3 1/2" clearance to remove crank handle. 4. When ordering power rewind models, prefix number with: A = Air Rewind E = Electric Rewind HD = Hydraulic Rewind (Air rewind reels are supplied with control valve and hose, 12v and 24v DC rewind reels are supplied with switch and solenoid, 115v AC rewind reels are not supplied with switch but can be ordered separately, hydraulic rewind reels are not supplied with control valve. *When shipped as a parcel package (via Fed-Ex or UPS Ground) 3
Series F For booster hose. To handle 3/4" I.D. or 1" I.D. hose. Series F The standard painted steel booster hose reel is the dependable, rugged reel that has set the standard for fire service reels for more than 50 years. The Super Booster reel is the top of the line. It weighs up to 50% less than standard booster reels and features an all-aluminum frame and drum, polished aluminum discs, and plated drive chain, sprocket, hub assembly, swivel joint and fasteners. No painting or finishing is required. When ordering place prefix SB before Model Number. Specifications and dimensions for Super Booster reels and standard booster hose reels are identical except for materials and weight. Rewind: Gear-driven crank rewind is standard. Choose chain and sprocket drive powered by electric, hydraulic or compressed air motor. Brakes & Locks: These reels supplied with a pinion brake as standard. Other brakes and locking devices may be specified. (See Ordering Guide & Accessory Catalog.) Inlet: Standard inlet is 1" 90-degree ball bearing swivel joint with 1" female NPT threads. Outlet: Standard outlet is 1" male NST threads. (1.375" x 8 threads per inch.) Other sizes and/or threads can be furnished and must be specified. Standard inlet, outlet riser and hub assembly are steel. These components can be supplied in stainless steel, at extra cost, to meet special product handling requirements. Optional Rollers: Rollers may be purchased as accessory items. Specify roller position when ordering. Mounting brackets are necessary. (See Ordering Guide & Accessory Catalog.) Operating Pressures & Temperatures: These reels operate at pressures to 1000 psi (69 bar) and handle product temperatures from 80º F to +185º F ( 62º C to+85º C). Reels to operate at other pressures and temperatures can be furnished at extra cost. CAUTION: When using Niedner Reeltex hose a special riser and/or larger drum diameter is required (consult factor y). 4
Series F Specifications Dimensions and capacities B E 6 1/2" 165 C 10.5" 267 G H X A F Series F Y D NOTICE: A FLEXIBLE CONNECTOR MUST BE USED BETWEEN THE INLET PIPE AND THE INLET SWIVEL JOINT. Be sure to check dimensions and weights prior to ordering. To receive a detailed parts breakdown drawing for Series F, request ISO 84, for Super Booster, request ISO 122. Hose Capacity of Reel Model Reel Dimensions Approx. Weight Approx. Weight Number inches (Steel) (Alum.) mm Crank Rewind Crank Rewind See Note 3 See Note 3 feet lb. lb. m NOTE 1 inch = 25.4 mm x, y indicate mounting holes kg. kg. I.D. (in) 3/4" 1" I.D. (mm) 19 26 For power rewind F O.D. (in) 1-9/32" 1-9/16" see Note 4 A B D E CRANK F F G H X Y NET SHIP NET SHIP O.D. (mm) 33 39 HYD ELEC AIR 150 100 *F32-19-21 29.5 24 20.5 21.62 34.25 34.25 34.38 21.5 12.12 21.5 16.75 102 144 80 122 46 30 749 610 521 549 870 870 873 546 308 546 425 46 65 36 55 150 100 *F24-23-24 21 15.5 20.5 23 25.75 25.75 25.88 23.5 12.12 13 16.75 92 134 75 117 46 30 533 394 521 584 654 654 657 597 308 330 425 42 61 34 53 250 150 *F30-23-24 27.5 22 20.5 23 32.25 32.25 32.38 23.5 12.12 19.5 16.75 105 147 82 124 76 46 699 559 521 584 819 819 822 597 308 495 425 48 67 37 56 350 200 *F38-23-24 35 29.5 20.5 23 39.75 41.75 39.88 23.5 12.12 27 16.75 120 162 92 134 107 61 889 749 521 584 1010 1060 1013 597 308 686 425 54 73 42 61 300 200 F28-25-26 25.5 20 25.5 24.75 30.25 32.25 30.38 27.88 15.5 17.5 21.75 113 155 87 129 91 61 648 508 648 629 768 819 772 708 394 445 552 51 70 39 59 400 250 F34-25-26 31.5 26 25.5 24.75 36.25 38.25 36.38 27.88 15.5 23.5 21.75 126 168 93 135 122 76 800 660 648 629 921 972 924 708 394 597 552 57 76 42 61 200 100 *F16.5-30-31 13.5 8 25.5 28.75 18.25 18.25 18.38 29.88 15.5 5.5 21.75 100 150 80 130 61 30 343 203 648 730 464 464 467 759 394 140 552 45 68 36 59 250 150 *F20-30-31 17 11.5 25.5 28.75 21.75 21.75 21.88 29.88 15.5 9 21.75 107 157 83 133 76 46 432 292 648 730 552 552 556 759 394 229 552 49 71 38 60 400 200 F24-30-31 21 15.5 25.5 28.75 25.75 27.75 25.88 29.88 15.5 13 21.75 113 163 87 137 122 61 533 394 648 730 654 705 657 759 394 330 552 51 74 39 62 500 250 F28-30-31 25.5 20 25.5 28.75 30.25 32.25 30.38 29.88 15.5 17.5 21.75 121 171 90 140 152 76 648 508 648 730 768 819 772 759 394 445 552 55 78 41 64 550 300 F30-30-31 27.5 22 25.5 28.75 32.25 34.25 32.38 29.88 15.5 19.5 21.75 125 175 92 142 168 91 699 559 648 730 819 870 822 759 394 495 552 57 79 42 64 650 350 F34-30-31 31.5 26 25.5 28.75 36.25 38.25 36.38 29.88 15.5 23.5 21.75 134 184 97 147 198 107 800 660 648 730 921 972 924 759 394 597 552 61 83 44 67 Specifications subject to change. Notes: 1. A two-way flow hub is available at no extra cost and must be specified. Assembly is threaded on both ends so swivel joint can be attached at either end of the reel. A pipe cap seals the opposite end. (See Ordering Guide & Accessory Catalog.) 2. Upon request, reels can be supplied with drum lengths other than shown and with disc sizes in other diameters. 3. Weights (lbs.) shown in chart are for manual rewind models. Add these amounts for power rewind models. Net (lbs.) Ship (lbs.) Net (kg.) Ship (kg.) Electric 40 40 18.1 18.1 Air 20 20 9.1 9.1 Hydraulic 20 20 9.1 9.1 4. When ordering power rewind models, prefix model number with: E = Electric rewind (1/3 HP) EP = Electric rewind (1/2 HP) A = Air rewind HD = Hydraulic Rewind (Air rewind reels are supplied with control valve and hose; 12v and 24v DC rewind reels are supplied with switch and solenoid, 115v AC rewind reels are not supplied with switch but can be ordered separately, hydraulic rewind reels are not supplied with control valve.) 5. For polished aluminum reels, prefix complete model number with SB ; for example: SBEF 32-19-21. * The F dimension for these models is shown for 1/3 HP motors. Add 2" to F dimension for 1/2 HP motors. The F dimension for all other reels is shown for 1/2 HP. Reels handling 200 or more must use 1/2 HP Motor. (Use prefix EP when ordering.) 6. When installing FH-3 rollers add 41/2 to D dimension. 5
Series SF For booster hose inboard mounted motor. To handle 3/4" I.D. or 1" I.D. hose. Series SF The inboard motor location and high profile of this reel make it suitable for installation in cabinets or wells that have space restrictions. All models are available as Super Booster reels with aluminum and plated components as described on page 4. Rewind: Gear-driven crank rewind is standard. Choose chain and sprocket drive powered by electric, hydraulic or compressed air motor. Brakes & Locks: These reels supplied with a pinion brake as standard. Other brakes and locking devices may be specified. (See ordering Guide & Accessory Catalog.) Inlet: Standard inlet is 1" 90-degree ball bearing swivel joint with 1" female NPT threads. Outlet: Standard outlet is 1" male NST threads (1.375" x 8 threads per inch). Other sizes and/or threads can be furnished and must be specified. Standard inlet, outlet riser and hub assembly are steel. These components can be supplied in stainless steel, at extra cost, to meet special product handling requirements. Optional Rollers: Rollers may be purchased as accessory items. Specify roller position when ordering. Mounting brackets are necessary. (See Ordering Guide & Accessory Catalog.) Operating Pressures & Temperatures: These reels operate at pressures to 1000 psi (69 bar) and handle product temperatures from 80º F to +185º F ( 62º C to+85º C). Reels to operate at other pressures and temperatures can be furnished at extra cost. CAUTION: When using Niedner Reeltex hose a special riser and/or larger drum diameter is required (consult factor y). 6
Series SF Specifications Dimensions and capacities B E 6 1/2 165 C 10.5" 267 G H X A F Series SF NOTICE: A FLEXIBLE CONNECTOR MUST BE USED BETWEEN THE INLET PIPE AND THE INLET SWIVEL JOINT. Be sure to check dimensions and weights prior to ordering. To receive a detailed parts breakdown drawing for Series SF, request ISO 84. Hose Capacity of Reel Model Reel Dimensions Approx. Weight Approx. Weight Number inches (Steel) (Alum.) mm Crank Rewind Crank Rewind See Note 3 See Note 3 feet lb. lb. m NOTE 1 inch = 25.4 mm x, y indicate mounting holes kg. kg. I.D. (in) 3/4" 1" I.D. (mm) 19 26 For power rewind O.D. (in) 1-9/32" 1-9/16" see Note 4 O.D. (mm) 33 40 A B D E F G H X Y NET SHIP NET SHIP 150 100 SF32-19-21 29 24 20.5 21.62 34 25.12 15.75 21.5 16.75 102 144 80 122 46 30 737 610 521 549 864 638 400 546 425 46 65 36 55 150 100 SF24-23-24 20.5 15.5 23.5 23 25.5 29.25 17.88 13 19.75 92 134 75 117 46 30 521 394 597 584 648 743 454 330 502 42 61 34 53 250 150 SF30-23-24 27 22 23.5 23 32 29.25 17.88 19.5 19.75 105 147 82 124 76 46 686 559 597 584 813 743 454 495 502 48 67 37 56 300 200 *SF28-25-26 25 20 25.5 24.75 30 30.88 18.5 17.5 21.75 113 155 87 129 91 61 635 508 648 629 762 784 470 445 552 51 70 39 59 400 250 *SF34-25-26 31 26 25.5 24.75 36 30.88 18.5 23.5 21.75 126 168 93 135 122 76 787 660 648 629 914 784 470 597 552 57 76 42 61 200 100 SF16.5-30-31 13 8 29 28.75 18 35.62 21.25 5.5 25.25 100 150 80 130 61 30 330 203 737 730 457 905 540 140 641 45 68 36 59 250 150 SF20-30-31 16.5 11.5 29 28.75 21.5 35.62 21.25 9 25.25 107 157 83 133 76 46 419 292 737 730 546 905 540 229 641 49 71 38 60 400 200 *SF24-30-31 20.5 15.5 29 28.75 25.5 35.62 21.25 13 25.25 113 163 87 137 500 61 521 394 737 730 648 905 540 330 641 51 74 39 62 500 250 *SF28-30-31 25 20 29 28.75 30 35.62 21.25 17.5 25.25 121 171 90 140 152 76 635 508 737 730 762 905 540 445 641 55 78 41 64 550 300 *SF30-30-31 27 22 29 28.75 32 35.62 21.25 19.5 25.25 125 175 92 142 168 91 686 559 737 730 813 905 540 495 641 57 79 42 64 650 350 *SF34-30-31 31 26 29 28.75 36 35.62 21.25 23.5 25.25 134 184 97 147 198 107 787 660 737 730 914 905 540 597 641 61 83 44 67 Y D Specifications subject to change. Notes: 1. A two-way flow hub is available at no extra cost and must be specified. Assembly is threaded on both ends so swivel joint can be attached at either end of the reel. A pipe cap seals the opposite end (See Ordering Guide & Accessory Catalog.) 2. Upon request, reels can be supplied with drum lengths other than shown and with disc sizes in other diameters. 3. Weights (lbs.) in chart are for manual rewind models. Add these amounts for power rewind models. Net (lbs.) Ship (lbs.) Net (kg.) Ship (kg.) Electric 40 40 18.1 18.1 Air 20 20 9.1 9.1 Hydraulic 20 20 9.1 9.1 4. When ordering power rewind models, prefix model number with: E = Electric Rewind (1/3 HP) EP = Electric Rewind (1/2 HP) A = Air Rewind HD = Hydraulic Rewind (12v and 24v DC rewind reels are supplied with switch and solenoid; 115v AC rewind reels are not supplied with switch but can be ordered separately.) (Use prefix EP when ordering.) 5. For polished aluminum reels, prefix complete model number with SB ; for example: SBESF32-19-21. 6. All frames are rollformed channel, except Super Booster, which is square tubing. * Reels handling 200 or more must use 1/2 HP Motor. 7
Kit TF Twin Kit for booster hose reels. To handle 3/4" I.D. or 1-1/2" I.D. hose. Two F Series Reels, and a Twin Fire Reel Conversion Kit High mount top wind position Two F Series Reels, and a Twin Fire Reel Conversion Kit and Two optional outrigger roller assemblies Twin booster hose reels combine matched F or FF Series reels in a single unit with a center-mounted roller and spool assembly. Hose from both reels can be used on either side of the truck. Rugged unit frame construction maintains alignment and simplifies installation when two reels are combined. All models are also available as Super Booster reel with aluminum and plated components as described on page 4 or pages 14-15. FH-3 Roller and Spool Assembly Not recommended for hoses larger than 1-1/2'' I.D. Speeds handling and reduces hose wear. Buffed stainless steel rollers resist corrosion, pitting and abrasion. Polished, chrome-plated spools and blocks add lasting beauty to your equipment. Delrin bearing surfaces assure quite operation and minimum wear. Assembly can be factory-installed, when specified, or ordered for field installation on reels or other equipment. To order: For factory installation, specify FH-3 Assembly and indicate position on reel. As a component, the complete model number of the reel must be specified. P/N 9939.0042 FH-3 Top Wind Outrigger Mounting Brackets P/N 9941.0023 8
TF Kit Specifications Dimensions and options Twin Fire Reel Conversion Kit FH-3 Roller Assembly Frame Components Part No. Description (model of reel must be specified) Steel Reels 9920.0050 Conversion Kit for Twin Fire Reel w/fh3 Roller Assembly for small steel pressed frame (23-24 and smaller) 9920.0051 Conversion Kit for Twin Fire Reel w/fh3 Roller Assembly for large steel pressed frame (25-26 and larger) 9920.0052 Conversion Kit for Twin Fire Reel w/fh3 Roller Assembly for 33-34 steel roll form frame Super Booster Reels 9920.0055 Conversion Kit for Twin Fire Reel w/fh3 Roller Assembly for small aluminum pressed frame (23-24 and smaller) 9920.0056 Conversion Kit for Twin Fire Reel w/fh3 Roller Assembly for large aluminum pressed frame (25-26 and larger) 9920.0057 Conversion Kit for Twin Fire Reel w/fh3 Roller Assembly for 33-34 aluminum roll form frame Dimensions of Twin Kit for F Series Reels: (in conjunction with chart on page 5, after assembly) for models ending with 23-24 25-26 30-31 33-34 E 48.5'' 52.5'' 60.5'' 66.5'' Dimension J 28.0'' 31.38'' 31.38'' 33.75'' E J Options: (model must be specified) For additional outrigger option (see lower photo top of page 8): you will need 2-9939.0042 FH-3 Roller & Spool assemblies, and 2-9941.0023 FH-3 Top Wind Outrigger Mounting Brackets. Assembly can be factory-installed, when specified, or ordered for field installation on reels or other equipment. 9
Series 7100/7200 For dual agent applications. To handle dual hose (3/4" I.D. thru 1 1/2" I.D.). Series 7100 Standard Configuration Shown These reels have two swivel joint inlets and two outlet risers to simultaneously handle two equal lengths of hose. Hoses can be different diameters, in which case the larger hose diameter determines the reel capacity. All models are available as Super Booster reel with aluminum and plated components as described on page 4. Rewind: Gear-driven crank rewind is standard. Choose chain and sprocket drive powered by electric, hydraulic or compressed air motor. Brakes & Locks: These reels supplied with a pinion brake as standard. Other brakes and locking devices may be specified. (See ordering Guide & Accessory Catalog.) Inlet: Series 7100 Standard inlets are 1" 90-degree ball bearing swivel joints with 1" female NPT threads. Series 7200 Standard inlets are 1 1/2" 90-degree ball bearing swivel joints with 1 1/2" female NPT threads and 2" victaulic groove. Outlets: Series 7100 Standard outlets are 1" male NST threads (1.375" x 8 threads per inch). Series 7200 Standard outlets are 1 1/2" male NST threads (1.990" x 9 threads per inch). Other sizes and/or threads can be furnished and must be specified. Standard inlets, outlet risers and hub assemblies are steel. These components can be supplied in stainless steel, at extra cost, to meet special product handling requirements. Optional Rollers: Rollers may be purchased as accessory items. Specify roller position when ordering. Mounting brackets are necessary. (See Ordering Guide & Accessory Catalog.) Operating Pressures & Temperatures: Series 7100 These reels operate at pressures to 1000 psi (69 bar) and handle product temperatures from 80º F to +185º F ( 62º C to+85º C). Series 7200 These reels operate at pressures to 600 psi (41 bar) and handle product temperatures from 20º F to +225º F ( 29º C to +107º C). Reels to operate at other pressures and temperatures can be furnished at extra cost. CAUTION: When using Niedner Reeltex hose a special riser and/or larger drum diameter is required (consult factor y). 10
Series 7100/7200 Specifications Dimensions and capacities B E 6 1/2 165 C 10.5" 267 G H X A F Series 7100/7200 Y D NOTICE: A FLEXIBLE CONNECTOR MUST BE USED BETWEEN THE INLET PIPE AND THE INLET SWIVEL JOINT. Be sure to check dimensions and weights prior to ordering. To receive a detailed parts breakdown drawing for Series 7100, request ISO 72, for Series 7200, request ISO 74. Hose Capacity of Reel Model Reel Dimensions Approx. Weight Number inches Crank Rewind mm See Note 2 feet lb. m NOTE 1 inch = 25.4 mm x, y indicate mounting holes kg. I.D. (in) 3/4" 1" 1-1/2" I.D. (mm) 19 25 38 For power rewind O.D. (in) 1-9/32" 1-9/16" 2-1/16" see Note 4 F F F F O.D. (mm) 33 40 52 A B D E CRANK ELEC AIR HYD G H X Y NET SHIP 2/100 2/50 ---- 7128-23-24 25.5 20 20.5 23 35 37 35.12 35 23.5 12.12 17.5 16.75 109 151 2/31 2/15 ---- 648 508 521 584 889 940 892 889 597 308 445 425 49 68 2/150 2/100 ---- 7130-25-26 27.5 22 25.5 24.75 37 39 37.12 37 27.88 15.5 19.5 21.75 125 175 2/46 2/31 ---- 699 559 648 629 940 991 943 940 708 394 495 552 57 79 2/200 2/125 ---- 7128-30-31 25.5 20 25.5 28.75 35 37 35.12 35 29.88 15.5 17.5 21.75 129 179 2/61 2/38 ---- 648 508 648 730 889 940 892 889 759 394 445 552 59 81 2/250 2/150 ---- 7128-33-34 25 20 31.5 31.75 34.5 36.5 35 35 33.62 17.75 17.5 27.75 129 179 2/76 2/46 ---- 635 508 800 806 876 927 889 889 854 451 445 705 59 81 ---- ---- 2/50 7230-25-26 27.5 22 25.5 24.75 40.5 40.75 40.5 40.5 27.88 15.5 19.5 21.75 144 194 ---- ---- 2/15 699 559 648 629 1029 1035 1029 1029 708 394 495 552 65 88 ---- ---- 2/50 7228-30-31 25.5 20 25.5 28.75 38.5 38.75 38.5 38.5 29.88 15.5 17.5 21.75 148 198 ---- ---- 2/15 648 508 648 730 978 984 978 978 759 394 445 552 67 90 ---- ---- 2/100 7230-33-34 27 22 31.5 31.75 40.5 40.5 40.5 40.5 33.62 17.75 19 27.75 160 210 ---- ---- 2/31 686 559 800 806 1029 1029 1029 1029 854 451 483 705 73 95 Specifications subject to change. Notes: 1. Upon request, reels can be supplied with drum lengths other than shown and with disc sizes in other diameters. 2. Weights in chart are for manual rewind models. Add these amounts for power rewind models. Net (lbs.) Ship (lbs.) Net (kg.) Ship (kg.) Electric 40 40 18.1 18.1 Air 20 20 9.1 9.1 Hydraulic 20 20 9.1 9.1 3. When ordering power rewind models prefix model number with: EP = Electric Rewind (1/2 HP) A = Air Rewind HD = Hydraulic Rewind (Air rewind reels are supplied with control valve and hose, 12v and 24v DC rewind reels are supplied with switch and solenoid 115v AC rewind reels are not supplied with switch but can be ordered separately, hydraulic rewind reels are not supplied with control valve.) 4. For polished aluminum reels, prefix complete model number with SB ; for example: SBEP 7128-23-24. 11
Series 3100/3600 For industrial fire protection. To handle 3/4" I.D. thru 1 1/2" I.D. hose. Series 3600 These reels are designed to handle booster hose or preconnected collapsible hose for in-plant, forestry and off shore fire protection systems. The reel can be installed on the floor or wall. Since water is always available at the reel, the reel can also be used for general warehouse and maintenance operations. These reels are constructed of steel, with optional construction of aluminum or stainless steel. Optional finishes of galvanized or special paint systems including E coat and marine grade finishes for salt water environments are available. Consult factory for additional information and pricing. Rewind: Choose disc rewind or removable direct crank rewind. Brakes & Locks: Reels are supplied with spring actuated pinlock. Other brakes and locks may be specified. (See Ordering Guide & Accessory Catalog.) Inlet: Series 3100 Standard inlet is 1" 90-degree ball bearing swivel joint with 1" female NPT threads. Series 3600 Standard inlet is 1 1/2" 90-degree ball bearing swivel joint with 1 1/2" female NPT threads and 2" victaulic groove. Standard Configuration Shown Outlet: Series 3100 Standard outlet is 1" male NST threads (1.375" x 8 threads per inch). Series 3600 Standard outlet is 1 1/2" male NST threads (1.990" x 9 threads per inch). Other sizes and/or threads can be furnished and must be specified. Standard inlet, outlet riser and hub assembly are steel. These components can be supplied in stainless steel, at extra cost, to meet special product handling requirements. Optional Rollers Rollers may be purchased as accessory items. Specify roller position when ordering. Mounting brackets are necessary. (See Ordering Guide & Accessory Catalog.) Optional Pressures & Temperatures: Series 3100 These reels operate at pressures to 1000 psi (69 bar) and handle product temperatures from 80º F to +185º F ( 62º C to+85º C). Series 3600 These reels operate at pressures to 600 psi (41 bar) and handle product temperatures from 20º F to +225º F ( 29º C to +107º C). Reels to operate at other pressures and temperatures can be furnished at extra cost. CAUTION: When using Niedner Reeltex hose a special riser and/or larger drum diameter is required (consult factor y). 12
Series 3100/3600 Specifications Dimensions and capacities E B G C 10.5" 267 H Y D 21.75" 552 25.5" 648 Series 3100/3600 X A F NOTICE: A FLEXIBLE CONNECTOR MUST BE USED BETWEEN THE INLET PIPE AND THE INLET SWIVEL JOINT. Be sure to check dimensions and weights prior to ordering. To receive a detailed parts breakdown drawing for Series 3100, request ISO 113, for Series 3600, request ISO 111. Hose Capacity of Reel Model Reel Dimensions Approx. Weight Number inches Crank Rewind feet mm lb. m kg. collapsible NOTE 1 inch = 25.4 mm x, y indicate mounting holes I.D. (in) 3/4" 1" 1-1/2" 1" 1-1/2" 1-3/4" I.D. (mm) 19 25 38 26 38 44 O.D. (in) 1-9/32" 1-9/16" 2-1/16" 1/2x1-3/4" 3/4"x3" 7/8"x3-1/4" O.D. (mm) 33 40 52 13x44 19x76 22x83 A B D E F G H X NET SHIP 100 50 200 3116-25-26 13 7.5 25.5 24 24.75 27.88 15.5 5 85 120 30 15 61 330 191 648 610 629 708 394 127 39 54 150 100 350 3120-25-26 17 11.5 25.5 24 28.75 27.88 15.5 9 94 129 46 30 107 432 292 648 610 730 708 394 229 43 59 250 150 450 3124-25-26 21 15.5 25.5 24 32.75 27.88 15.5 13 103 138 76 46 137 533 394 648 610 832 708 394 330 47 63 300 200 650 3128-25-26 25.5 20 25.5 24 32.75 27.88 15.5 17.5 113 155 91 61 198 648 508 648 610 832 708 394 445 51 70 50 50 50 3616-25-26 13 7.5 25.5 24 26 27.88 15.5 5 95 130 15 15 15 330 191 648 610 660 708 394 127 43 59 100 50 100 75 3620-25-26 17 11.5 25.5 24 30 27.88 15.5 9 104 139 30 15 30 23 432 292 648 610 762 708 394 229 47 63 150 75 150 100 3624-25-26 21 15.5 25.5 24 34 27.88 15.5 13 113 148 46 23 46 30 533 394 648 610 864 708 394 330 51 67 200 100 200 150 3628-25-26 25.5 20 25.5 24 38.5 27.88 15.5 17.5 123 173 61 30 61 46 648 508 648 610 978 708 394 445 56 78 200 100 250 150 3624-30-31 21 15.5 25.5 30 34 30.38 16 13 124 174 61 30 76 46 533 394 648 762 864 772 406 330 56 79 275 150 300 250 3628-30-31 25.5 20 25.5 30 38.5 30.38 16 17.5 134 184 84 46 91 76 648 508 648 762 978 772 406 445 61 83 375 200 400 350 3634-30-31 31.5 26 25.5 30 44.5 30.38 16 23.5 147 197 114 61 122 107 800 660 648 762 1130 772 406 597 67 89 400 250 450 350 3630-33-34 27.5 22 25.5 31.75 40.5 32.38 16.5 19.5 138 188 122 76 137 107 699 559 648 806 1029 822 419 495 63 85 Specifications subject to change. Notes: 1. Upon request, reels can be supplied with drum lengths other than shown and with disc sizes in other diameters. 2. Power rewind are not available on these models. See Series F or FF. 3. Four inches clearance needed for crank handle removal. 13
Series FF For large booster hose or preconnected collapsible hose. To handle 1 1/4" I.D. or 1 1/2" I.D. booster hose or 1 1/2" I.D. or 1 3/4" I.D. collapsible hose. Series FF Standard Configuration Shown These reels have a 1 1/2" I.D. full-flow hub assembly to accommodate large diameter booster hose or preconnected collapsible hose. The flanged outlet riser can be removed for easy hose installation. All models listed can be supplied without inlet, outlet riser, or hub assembly for dry storage of collapsible hose. All models are available as Super Booster reel with aluminum and plated components as described on page 4. Rewind: Gear-driven crank rewind is standard. Choose chain and sprocket drive powered by electric, hydraulic or compressed air motor. Brakes & Locks: These reels supplied with a pinion brake as standard. Other brakes and locking devices may be specified. (See ordering Guide & Accessory Catalog.) Inlet: Standard inlet is 1 1/2" 90-degree ball bearing swivel joint with 1 1/2" female NPT threads and 2" victaulic groove. Outlet: Standard outlet is 1 1/2" male NST threads. (1.990" x 9 threads per inch.) Other sizes and/or threads can be furnished and must be specified. Standard inlet, outlet riser and hub assembly are steel. These components can be supplied in stainless steel, at extra cost, to meet special product handling requirements. Optional Rollers: Rollers may be purchased as accessory items. Specify roller position when ordering. Mounting brackets are necessary. (See Ordering Guide & Accessory Catalog.) Operating Pressures & Temperatures: These reels operate at pressures to 600 psi (41 bar) and handle product temperatures from 60º F to +175º F ( 51º C to +79º C). Reels to operate at other pressures and temperatures can be furnished at extra cost. CAUTION: When using Niedner Reeltex hose a special riser and/or larger drum diameter is required (consult factor y). 14
Series FF Specifications Dimensions and capacities B E 6 1/2 165 C 10.5" 267 G H NOTICE: A FLEXIBLE CONNECTOR MUST BE USED BETWEEN THE INLET PIPE AND THE INLET SWIVEL JOINT. Be sure to check dimensions and weights prior to ordering. To receive a detailed parts breakdown drawing for Series FF, request ISO 18. Specifications subject to change. Notes: 1. Upon request, reels can be supplied with drum lengths other than shown and with disc sizes in other diameters. 2. Weights in chart are for manual rewind models. Add these amounts for power rewind models. Net (lbs.) Ship (lbs.) Net (kg.) Ship (kg.) Electric 40 40 18.1 18.1 Air 20 20 9.1 9.1 Hydraulic 20 20 9.1 9.1 X A F Series FF Hose Capacity of Reel Model Reel Dimensions Approx. Weight Approx. Weight Number inches (Steel) (Alum.) mm Crank Rewind Crank Rewind feet See Note 3 See Note 3 m lb. lb. collapsible NOTE 1 inch = 25.4 mm x, y indicate mounting holes kg. kg. I.D. (in) 1-1/4" 1-1/2" 1-1/2" 1-3/4" I.D. (mm) 32 38 38 44 For power rewind O.D. (in) 1-13/16" 2-1/16" 3/4"x3" 7/8"x3-1/4" see Note 3 O.D. (mm) 46 52 19x76 22x83 A B D E F G H X Y NET SHIP NET SHIP 100 50 150 125 FF28-23-24 25.5 20 20.5 23 32.25 23.5 12.12 17.5 16.75 111 153 80 122 30 15 46 38 648 508 521 584 819 597 308 445 425 50 69 36 55 100 100 200 175 FF28-25-26 25.5 20 25.5 24.75 32.25 27.88 15.5 17.5 21.75 123 165 90 132 30 30 61 53 648 508 648 629 819 708 394 445 552 56 75 41 60 75 50 100 75 FF16-30-31 13 7.5 25.5 28.75 19.75 29.88 15.5 5 21.75 110 160 83 133 23 15 30 23 330 191 648 730 502 759 394 127 552 50 73 38 60 100 75 150 75 FF18-30-31 15 9.5 25.5 28.75 21.75 29.88 15.5 7 21.75 114 164 85 135 30 23 46 23 381 241 648 730 552 759 394 178 552 52 74 39 61 250 150 300 250 FF28-30-31 25.5 20 25.5 28.75 32.25 29.88 15.5 17.5 21.75 131 181 93 143 76 46 91 76 648 508 648 730 819 759 394 445 552 59 82 42 65 125 100 200 150 FF20-33-34 16.5 11.5 31.5 31.75 23.25 33.62 17.75 9 27.75 120 174 88 142 38 30 61 46 419 292 800 806 591 854 451 229 705 54 79 40 64 150 150 250 200 FF22-33-34 18.5 13.5 31.5 31.75 25.25 33.62 17.75 11 27.75 125 179 91 145 46 46 76 61 470 343 800 806 641 854 451 279 705 57 81 41 66 3. When ordering power rewind models, prefix model number with: EP = Electric Rewind ( 1 /2 H.P.) A = Air Rewind HD = Hydraulic Rewind (Air rewind reels are supplied with control valve and hose; 12v and 24v DC rewind reels are supplied with switch and solenoid. 115 v AC rewind reels are not supplied with switch but can be ordered separately, hydraulic rewind reels are not supplied with control valve.) 4. For polished aluminum reels, prefix complete model number with SB ; for example: SBEPFF28-23-24. 5. Dimensions shown for reels up to and including 30-31 disc size reflect pressed frames. All others are rollformed channel frames, except Super Booster, which is square tubing. Y D 15
Series LD Reels and spools to handle up to 6" I.D. collapsible hose. Typical Installations: Single large-capacity reel installed in the hose bed area to handle long lengths of pre-coupled hose. Hose pays out from the top of the reel so gravity assists unwinding. Two reels installed in the hose bed. In this arrangement, the upper reel is unloaded only if necessary. Payout and rewinding of the upper reels are facilitated by the position of the lower reel. Two reels with larger-diameter discs and narrower drums can also be installed sideby-side in the rear of the hose bed to handle approximately the same amount of hose. This method allows a center walkway or paying out two lines simultaneously if required. Hannay Reels offer the most efficient method of handling large diameter collapsible hose. Payout is fast and direct. Rewinding is considerably faster than reloading a hose bed, and reeling the hose eliminates sharp bends in the hose. Drainage is also facilitated by reeling. Location of these large reels on the apparatus is unique to each fire department and its specific needs. A single large reel is favored by some departments, while others find a pair of somewhat smaller reels to be more efficient. The illustrations above show frequently used installations and they are intended only as a guide. Hannay Reels standard reels for large-diameter collapsible hose are of all-steel construction; however, they can be constructed of all-aluminum if required for finish and weight considerations. Reel and Spool Specifications Description: Spools include discs, drum, axle and sprocket for chain. (Chain and rewind motor not supplied.) Spool assemblies include all components except the frame which is fabricated by the apparatus builder. Reel assemblies include discs, drum, axle, pillow block bearings, rewind mechanism, motor and frame. Discs are either heavy gauge steel with rolled edges and concentric reinforcing ribs or 3/16" thick steel with 1/2" rod welded around circumference (also available in aluminum). Drums are formed by reinforced tie rods with radial supports. Frames are heavy duty square tubing. Rewind options: Chain and sprocket drive mechanism powered by electric or hydraulic rewind motors. Electric rewind system includes 12v or 24v DC motor with reversible leads, remote push-button operating switch, solenoid and connectors. A clutch reduction unit is standard and installed on the reel assembly to increase torque and permit slower operating speeds. The rewind motor can be installed inboard or outboard of the reel frame. A variety of hydraulic rewind systems can be configured with standard hydraulic components (see hydraulic circuit information on page 17). Reel and spool assemblies are equipped with a reversible type hydraulic motor with SAE O-ring fittings. Other hydraulic system components are supplied by truck or vehicle manufacturer. Consult factory for hydraulic motor requirements. Brakes: A caliper disc brake system is supplied, when specified, to control reel unwinding speed (when free-wheeling) and/or to lock the reel while the vehicle is traveling. The brake is hydraulically operated and is self-contained. Important: Hose capacity is based on the flat hose dimensions listed below, with couplings at 100 foot intervals. Flat Hose Dimensions THICK x WIDTH I.D. THICK x WIDTH METRIC EQUIVALENT 1" 1 /2" x 1 3 /4" 12.7 x 44.4 1 1 /2" 3 /4" x 3" 19.0 x 76.2 1 3 /4" 7 /8" x 3 1 /4" 22.2 x 79.4 2" 3 /4" x 3 1 /2 19.0 x 88.9 2 1 /2" 3 /4" x 4" 19.0 x 101.6 3" 1 /2" x 5" 12.7 x 127.0 4" 1 /2" x 6 1 /2" 12.7 x 165.1 5" 1 /2" x 8" 12.7 x 203.2 6" 1 /2" x 10" 12.7 x 254.0 16
LD Reels and Spools Installation Guide Hydraulic Requirements It is IMPORTANT that the End user provide the O.E.M. with complete specifications as to the required operation of the large diameter reel being specified. Any speed and torque requirements MUST be known to properly specify the correct reel for the application. The schematics shown here are EXAMPLES ONLY! THE CORRECT PUMP AND HYDRAULICS ARE THE RESPONSIBILITY OF THE TRUCK MANUFACTURER, in conjunction with the PURCHASER. Notes: 1. The schematics shown are for reference only and may not necessarily reflect customer requirements. 2. Hannay Reels does not recommend specific brands for hydraulic system components. We suggest you work with your hydraulic component supplier to meet your specs. Series LD Reel with hydraulic motor rewind and optional caliper disc brake installed. Custom Reels The standard reel assembly and spool assembly models listed represent the most frequently specified customer requirements for handling large-diameter fire hose. Because of the many possible variations in reel installation and hose capacity requirements, we will also custom build reels and spools to your specifications to become an integral part of the apparatus. Reels can be built of either steel or aluminum construction and various finishes are available. 17
LD REEL & SPOOL CONFIGURATIONS Reel & Spool Configurations Version A, B, and C: Version A Spool with sprocket for No. 50 chain. Chain and rewind motor not supplied. Version B Spool assembly with No. 50 chain and sprocket and hydraulic rewind motor. Version C Spool assembly with No. 41 chain and sprocket and electric rewind motor with clutch and double reduction unit. Disc diameters (E dimension) up to and including 39" only. Version F Reel: Version F Complete reel assembly with No. 50 chain and sprocket and hydraulic rewind motor mounted inside the frame. When ordering use prefix model number with HD; for example, HDLD 350-64 version F. Version G Reel: Version G (high profile) complete reel assembly with chain and sprocket drive and electric rewind motor, including clutch and double reduction unit. Motor is mounted inside the frame. Disc diameters (E dimension) up to and including 39" only. When ordering use prefix model number with EP; for example, EPLD 242-39 version G. F dimension = A dimension +4 C C C 10.5 267 10.5 267 10.5 267 Version H Reel: Version H (low profile) complete reel assembly with chain and sprocket drive and electric rewind motor, including clutch and double reduction unit. Motor is mounted outside the frame. Disc diameters (E dimension) up to and including 39" only. When ordering use prefix model number with EP; for example, EPLD 242-39 version H. Subtract 5" from dimensions G and H in chart for this version. F dimension = A dimension +7 C 10.5 267 18
Series LD Specifications See Reel & Spool Configurations on page 18. Be sure to check dimensions and weights prior to ordering. To receive a detailed parts breakdown drawing for Series LD, request ISO 104. Hose Capacity of Reel Model Reel Dimensions Approx. Weight Number NOTE 1 inch = 25.4 mm (Steel) Power Rewind feet inches lb. m mm kg. I.D. (in) 1-1/2" 1-3/4" 2" 2-1/2" 3" 4" 5" 6" I.D. (mm) 38 44 51 64 76 102 127 152 A B D E G H NET SHIP 800 600 600 600 600 500 350 LD268-30 63 54 30.5 30 39 24 370 450 244 183 183 183 183 152 107 1600 1372 775 762 991 610 168 204 1000 700 800 700 800 600 250 LD268-33 63 54 33.5 33 42 25.5 385 465 305 213 244 213 244 183 76 1600 1372 851 838 1067 648 175 211 400 350 350 400 300 200 LD234-39 29 20 39.5 39 45 25.5 365 465 122 107 107 122 91 61 737 508 1003 991 1143 648 166 211 500 600 500 500 400 300 LD242-39 37 28 39.5 39 45 25.5 381 481 152 183 152 152 122 91 940 711 1003 991 1143 648 173 218 1100 800 600 LD262-39 57 48 39.5 39 45 25.5 421 521 335 244 183 1448 1219 1003 991 1143 648 191 236 1050 800 LD274-39 69 60 39.5 39 45 25.5 445 545 320 244 1753 1524 1003 991 1143 648 202 247 500 400 LD242-45 37 28 45.5 45 51 28.5 427 557 152 122 940 711 1156 1143 1295 724 194 253 1100 900 LD262-45 57 48 45.5 45 51 28.5 467 597 335 274 1448 1219 1156 1143 1295 724 212 271 1400 1100 LD274-45 69 60 45.5 45 51 28.5 491 621 427 335 1753 1524 1156 1143 1295 724 223 282 800 500 300 LD242-52 37 28 52.5 52 58 32 581 731 244 152 91 940 711 1334 1321 1473 813 264 332 Electric rewind not available on these models. Specifications subject to change. Note: 1. Upon request, reels can be supplied with drum lengths other than shown and with disc sizes in other diameters. 1500 1300 800 LD262-52 57 48 52.5 52 58 32 621 771 457 396 244 1448 1219 1334 1321 1473 813 282 350 2000 1500 1200 LD274-52 69 60 52.5 52 58 32 645 795 610 457 366 1753 1524 1334 1321 1473 813 283 361 1300 1000 700 LD250-56 45 36 56.5 56 62 34 657 817 396 305 213 1143 914 1435 1422 1575 864 298 371 1800 1500 900 LD262-56 57 48 56.5 56 62 34 681 841 549 457 274 1448 1219 1435 1422 1575 864 309 381 2300 1700 1400 LD274-56 69 60 56.5 56 62 34 705 865 701 518 427 1753 1524 1435 1422 1575 864 320 392 1700 1300 900 LD350-64 47.25 36 64.75 64 70 38 1130 1330 518 396 274 1200 914 1645 1626 1778 965 513 603 3000 2300 1900 LD374-64 71.25 60 64.75 64 70 38 1200 1400 914 701 579 1810 1524 1645 1626 1778 965 544 635 19
NOTES 20
It s easier to handle hose from booster to large diameter hose when Hannay Reels are lending a hand.
Narrow roads in an old fishing village such as ours require long lengths of large diameter hose for proper water volume. Hannay Series LD fit the bill perfectly, fast payout and pickup answered our needs. Jim Burrows, Fire Coordinator Kennebunkport (ME) Fire Department Fire fighting and rescue operations all around the country depend on Hannay Reels. For years, Hannay has produced the best fire fighting and rescue hose and cable reels found anywhere in the world. Fire fighters and rescue squads have come to depend on Hannay Reels for their dependability, ease of use, and long life. But don t take our word for it. Here s what some of our customers have to say about Hannay Reels. Hannay Reels gives us easy hose dispersal and quick pick-up. Malcolm Farrell, Wilson Fire Department, Windsor, CT. The speed of our first attack is crucial, and Hannay Reels give us instant on with even partial payout. So we re right where the emergency is. Peter Goldstein, Coram, Long Island (NY) Fire Department In rescue operations, you have to be fast to be effective. Hannay Reels save us time in payout and clean-up. John Dugan, Wellsboro (PA) Fire Department To order Hannay Reels. Please refer to our Ordering Guide & Accessory Catalog enclosed in this package. For more information on all our hose and cable reels for fire fighting and rescue operations, please request our Triad Rescue Reels Catalog. 1st Lt. George Conklin of Unexcelled Fire Company states, Hannay makes the hardest job easier. When the men are exhausted and fatigued from fighting a fire, they can pack up the hose in one-third the time. Available from: The reel leader. 553 State Route 143 Westerlo, NY 12193-0159 Telephone 518-797-3791 TOLL FREE 1-877-GO REELS FAX 1-800-REELING (733-5464) USA or FAX 518-797-3259 (International) WSP 10M 12/02 Email: H-9407-F Revision 6