Collet Chuck manual 08/2010
Contents: FNP manual collet chuck...4/5 draw-back type W20 / W25 / 5C / B32 / 386E FNP manual collet chuck...6/7 draw-back type B45 FNH manual collet chuck...8/9 draw-back type Hainbuch Gr. 32 / Gr. 42 / Gr. 65 FNF manual collet chuck...10/11 pressure type F32 / F35 / F38 / F48 / F66 FN lever-action quick clamping collet chuck CLC...12/13 type F35 163E / F48 173E / F66 185E draw-back collet chuck type W20 / W25 / W31.75 / B32 / B45...14 pressure collet chuck type F35 / F38 / F48 / F66...15 chuck heads type size 32 / 42...16 chuck heads type size 65...17 Jacobs rubber flex collets type F48 / F66...18 stop bar spindle stop (Rivelica)...18 collet stop...19 custom-made products to meet specific requirements...19
SW FNP manual collet chuck draw-back type W20 / W25 / 5C / B32 / 386E D J B G B2 B1 A F 0.015 E H C Technical features: - Operation using chuck key on chuck body - DIN 6350 standard mounting - Can be used for the following collets: - Schaublin model W20/W25/386E/B32 draw-back collets - American model 5C standard collet chucks - Can be used on lathes, milling machines and drilling machines - Available with all current mountings, such as W20/W25 thread, Camlock DIN 55029, DIN 55027 bayonet, ASA-2 DIN 55026 or with fl ange fi tting onto special mounting to suit customer s requirements. Standard accessories: 1 chuck key, 1 set of retaining screws Chuck size W 20 W 25 5 C (Schaublin W 31.75) B 32 386 E A 126 126 126 126 126 B 96.5 120.5 108 119 128 B1 36.5 60.5 48 59 68 B2 53 76.5 64.5 75.5 84.5 C 4 4 4 4 4 D H7 95 95 95 95 95 E 40 48 53 53 53 F 108 108 108 108 108 G 3 x 8.5 3 x 8.5 3 x 8.5 3 x 8.5 3 x 8.5 H 54 59 62 62 62 J 88 88 88 88 88 Wrench Size 9 9 9 9 9 max. speed U/min 6000 6000 6000 6000 6000 110-305 110-306 110-307 110-308 110-309 4 technical subject to change
Flanges ready machined on both sides and adapted to suit the chuck DIN 55026 ASA A 2-...; cast Mounting size A 3 A 4 A 5 A 6 A 8 A 11 340-603/3 340-604/3 340-605/3 340-606/3 340-608/3 340-611/3 DIN 55027 bayonet; stay bolts and fl anged nuts; cast Mounting size B 3 B 4 B 5 B 6 B 8 B 11 341-603/3 341-604/3 341-605/3 341-606/3 341-608/3 341-611/3 DIN 55029 Camlock D 1-...; cast Mounting size S 3 S 4 S 5 S 6 S 8 S 11 342-603/3 342-604/3 342-605/3 342-606/3 342-608/3 342-611/3 technical subject to change 5
FNP manual collet chuck draw-back type B 45 B E B1 A D S W 0.015 F C C 1 T Technical features: - Operation using chuck key on chuck body - DIN 6350 standard mounting - Can be used for the following collets: - B45 draw-back collets - Can be used on lathes, milling machines and drilling machines - Available with all current mountings, such as W20/W25 thread, Camlock DIN 55029, DIN 55027 bayonet, ASA-2 DIN 55026 or with fl ange fi tting onto special mounting to suit customer s requirements. Standard accessories: 1 chuck key 1 set of retaining screws Chuck size B 45 Matching collet B 45 Clamping range (mm) 1-36 A 160 B 150 B1 76 C 65 C1 96 D H6 125 E 3 x M10 F 140 T 5 Wrench size 11 max. speed U/min 4500 110-345 6 technical subject to change
Flanges ready machined on both sides and adapted to suit the chuck DIN 55026 ASA A 2-...; cast Mounting size A 3 A 4 A 5 A 6 A 8 A 11 340-603/4 340-604/4 340-605/4 340-606/4 340-608/4 340-611/4 DIN 55027 bayonet; stay bolts and fl anged nuts; cast Mounting size B 3 B 4 B 5 B 6 B 8 B 11 341-603/4 341-604/4 341-605/4 341-606/4 341-608/4 341-611/4 DIN 55029 Camlock D 1-...; cast Mounting size S 3 S 4 S 5 S 6 S 8 S 11 342-603/4 342-604/4 342-605/4 342-606/4 342-608/4 342-611/4 technical subject to change 7
FNH manual collet chuck draw-back type Hainbuch manual Technical features: - Operation using chuck key on chuck body - DIN 6350 standard mounting - Can be used for the following collets: - chuck heads type size 65 - Can be used on lathes, milling machines and drilling machines - Available with all current mountings, such as W20 / W25 thread, Camlock DIN 55029, DIN 55027 bayonet, ASA-2 DIN 55026 or with fl ange fi tting onto special mounting to suit customer s requirements. Standard accessories: 1 chuck key 1 set of retaining screws Chuck size FNH Gr. 32 FNH Gr. 42 FNH Gr. 65 Matching collet chuck heads size 32 chuck heads size 42 chuck heads size 65 Clamping range (mm) 4-32 4-42 5-65 A 160 160 200 B 110 110 112.80 B1 18 30 35 C 72 95 125 D H6 125 125 160 E 3 x M10 3 x M10 3 x M10 F 140 140 176 T 5 5 5 SW 11 11 11 max. speed U/min 4500 4500 4000 110-332 110-342 110-465 8 technical subject to change
Flanges ready machined on both sides and adapted to suit the chuck DIN 55026 ASA A 2-...; cast Mounting size A 3 A 4 A 5 A 6 A 8 A 11 340-603/4 340-604/4 340-605/4 340-606/4 340-608/4 340-611/ FN-H65 340-603/5 340-604/5 340-605/5 340-606/5 340-608/5 340-611/5 DIN 55027 bayonet; stay bolts and fl anged nuts; cast Mounting size B 3 B 4 B 5 B 6 B 8 B 11 341-603/4 341-604/4 341-605/4 341-606/4 341-608/4 341-611/4 FN-H65 341-603/5 341-604/5 341-605/5 341-606/5 341-608/5 341-611/5 DIN 55029 Camlock D 1-...; cast Mounting size S 3 S 4 S 5 S 6 S 8 S 11 342-603/4 342-604/4 342-605/4 342-606/4 342-608/4 342-611/4 FN-H65 342-603/5 342-604/5 342-605/5 342-606/5 342-608/5 342-611/5 Manual changing device for chuck heads Size Gr. 32 Gr. 42 Gr. 65 on enquiry 196842 196844 technical subject to change 9
S W FNF manual collet chuck pressure Typ F32 / F35 / F38 / F48 / F66 B B1 0.02 E A F D C T Technical features: - Operation using chuck key on chuck body - DIN 6350 standard mounting - Can be used for the following collets: - pressure collet chuck type F32 (161E) / F35 (163E) / F38 (164E) / F48 (173E) / F66 (185E) - Can be used on lathes, milling machines and drilling machines - Available with all current mountings, such as W20/W25 thread, Camlock DIN 55029, DIN 55027 bayonet, ASA-2 DIN 55026 or with fl ange fi tting onto special mounting to suit customer s requirements. Standard accessories: 1 chuck key 1 hook wrench 1 set of retaining screws Chuck size F 32 F 35 F 38 F 48 F 66 Matching collet F 32 / 161 E F 35 / 163 E F 38 / 164 E F 48 / 173 E F 66 / 185 E Clamping range (mm) 1-26 2-30 2-32 3-42 4-60 A 160 160 160 160 200 B 115 115 115 115 125 B1 40 40 40 40 78 C 90 90 90 90 152 D H6 125 125 125 125 160 F 140 140 140 140 176 E 3 x 10.5 3 x 10.5 3 x 10.5 3 x 10.5 3 x 10.5 T 5 5 5 5 5 Wrench size 11 11 11 11 11 max. speed U/min 4500 4500 4500 4500 4000 110-332 110-335 110-338 110-348 110-466 10 technical subject to change
Flanges ready machined on both sides and adapted to suit the chuck DIN 55026 ASA A 2-...; cast Mounting size A 3 A 4 A 5 A 6 A 8 A 11 340-603/4 340-604/4 340-605/4 340-606/4 340-608/4 340-611/4 FN-F66 340-603/5 340-604/5 340-605/5 340-606/5 340-608/5 340-611/5 DIN 55027 bayonet; stay bolts and fl anged nuts; cast Mounting size B 3 B 4 B 5 B 6 B 8 B 11 341-603/4 341-604/4 341-605/4 341-606/4 341-608/4 341-611/4 FN-F66 341-603/5 341-604/5 341-605/5 341-606/5 341-608/5 341-611/5 DIN 55029 Camlock D 1-...; cast Mounting size S 3 S 4 S 5 S 6 S 8 S 11 342-603/4 342-604/4 342-605/4 342-606/4 342-608/4 342-611/4 FN-F66 342-603/5 342-604/5 342-605/5 342-606/5 342-608/5 342-611/5 technical subject to change 11
FN lever-action quick clamping collet chuck CLC type F35 163E / F48 173E / F66 185E Quick clamping by hand for Schaublin F collet chucks - With cylindrical centring mounting - Flanging of the chuck takes place taking into consideration the spindle design as in the case of a 3-jaw chuck when using a cylinder fl ange. The opening corresponds to the clamping range. - Available with all current mountings, such as W20/W25 thread, Camlock DIN 55029, DIN 55027 bayonet, ASA-2 DIN 55026 or with fl ange fi tting onto special mounting to suit customer s requirements. Type / F-collet 28 / F35 42 / F48 60 / F66 F35 / 163E F48/ 173E F66 / 185E Clamping range (mm) 2-30 3-42 4-60 L max. 108.5 114 134 L 75 100 102 D 72 88 115 D 1 90 107 131 D 2 105 122 150 235-281 248-421 260-661 12 technical subject to change
Flanges ready machined on both sides and adapted to suit the chuck DIN 55027 bayonet; stay bolts and fl anged nuts; cast Mounting size for type CLC 28 / F35 for type CLC 42 / F48 for type CLC 60 / F66 B 3 341-503 341-603 - B 4 341-504 341-604 341-704 B 5 341-505 341-605 341-705 B 6 341-506 341-606 341-706 B 8 341-508 341-608 341-709 B 11 341-511 341-611 341-711 DIN 55029 Camlock D 1-...; cast Mounting size for type CLC 28 / F35 for type CLC 42 / F48 for type CLC 60 / F66 S 3 342-503 342-603 - S 4 342-504 342-604 342-704 S 5 342-505 342-605 342-705 S 6 342-506 342-606 342-406 S 8 342-508 342-608 342-708 S 11 342-511 342-611 342-711 DIN 55026 ASA A 2-...; cast Mounting size for type CLC 28 / F35 for type CLC 42 / F48 for type CLC 60 / F66 A 3 240-503 340-603 - A 4 340-5047 340-604 340-704 A 5 340-505 340-605 340-705 A 6 340-506 340-606 340-706 A 8 340-508 340-608 340-709 A 11 340-511 340-611 340-711 technical subject to change 13
draw-back collet chuck type W20/W25/W31.75/B32/B45 Type / A D from up to rising (mm) L G B C angle round 0.3 0.4 0.1 round 0.5 0.9 0.1 round 1.0 1.4 0.1 constant round 1.5 2.9 0.1 W 20 / 20 round 3.0 14.5 0.5 19.7 x 349E 26.3 73 15 round 14.51 16 0.5 28 15G/`` square 4 10 1 constant square 11 14 1 7.5 hexagonal 4 12 1 constant hexagonal 12 16 1 7.5 Type / A D from up to rising (mm) L G B C angle Rund 0.5 0.9 0.1 Rund 1 1.4 0.1 Rund 1.5 2.5 0.5 constant Rund 3.0 19.05 0.5 W 25 / 25 24.7 x Rund 19.06 21 0.5 12.5 364E 15G/`` square 4 13 1 constant 33.7 97.6 15 square 14 16 1 12.5 hexagonal 4 16 1 constant hexagonal 17 20 1 12.5 Type / A D from up to rising (mm) L G B C angle W 31.75, 5C / Rund 1.5 2.5 0.5 31.4 x 31.75 Rund 3 30 0.5 constant 37.3 87 15 15G/`` 385E hexagonal 5.0 20.0 1.0 Type / A D from up to rising (mm) L G B C angle round 1.5 2.5 0.1 constant round 3 24 0.5 constant B 32 / 32 round 24.01 28 0.5 44 29.7 x round 28.01 30 0.5 12 20G/`` round 30.01 32 0.5 8 40 106 15 square 4 17 1.0 hexagonal 4 20 1.0 constant Type / A D from up to rising (mm) L G B C angle 3 36 1 constant B 45 / 45 37 40.99 1 53 42, 41 41.99 1 14 M42 42 42.99 1 12 x 1.5 43 43.99 1 10 53 115 15 44 45.00 1 8 - example: B32/12 - round 12 mm B32/c12 - square 12 mm B32/s12 - hexagonal 12 mm 14 technical subject to change
pressure collet chuck type F35/F38/F48/F66 Type / A DIN D from up to rising (mm) A B C angle F 35 63 43 163E round 2.0 2.5 0.5 round 3.0 30 0.5 square 5.0 20 1.0 hexagonal 4.0 24 1.0 35 48 80 15 Type / A DIN D from up to rising (mm) A B C angle F 38 6343 164E round 2.0 2.5 0.5 round 3.0 32 0.5 square 4.0 22 1.0 hexagonal 4.0 27 1.0 38.08 49 107.5 15 Type / A DIN D from up to rising (mm) A B C angle F 48 6343 173E round 2.0 2.5 0.5 round 3.0 42 0.5 square 4.0 30 1.0 hexagonal 6.0 36 1.0 48 60 94 15 Type / A DIN D from up to rising (mm) A B C angle F 66 6343 185E round 4.0 60 1.0 square 7.0 40 1.0 hexagonal 10 51 1.0 66 84 110 15 - example: F48/12 - round 12 mm F48/c12 - square 12 mm F48/s12 - hexagonal 12 mm technical subject to change 15
chuck heads type size 32 Steel collets with axial and radial grooves (*smooth, **radial grooves - round) 4* 5* 6* 7* 8** 9** 10** 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Steel collets with smooth clamping surface (round) 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Steel collets with smooth clamping surface (square) Square 7* 8** 9** 10** 11** 12** 13** 14** 15** 16** 17** 18** 19** Square 20** 21** 22** Steel collets with smooth clamping surface (hexagonal) Hexagonal 7* 8** 9** 10** 11** 12** 13** 14** 15** 16** 17** 18** 19** Hexagonal 20** 21** 22** 23** 24** 25** 26** 27** chuck heads type size 42 Steel collets with axial and radial grooves (*smooth, **radial grooves - round) 4* 192173 17 192186 30 192199 5* 192174 18 192187 31 192200 6* 192175 19 192188 32 192201 7* 192176 20 192189 33 192202 8** 192177 21 192190 34 192203 9** 192178 22 192191 35 192204 10** 192179 23 192192 36 192205 11 192180 24 192193 37 192203 12 192181 25 192194 38 192207 13 192182 26 192195 39 192208 14 192183 27 192186 40 192209 15 192184 28 192197 41 192210 16 192185 29 192198 42 192211 Steel collets with smooth clamping surface (round) 4 192173 17 193144 30 193155 5 192174 18 192807 31 193156 6 192175 19 192807 32 193083 7 192176 21 193146 33 193157 8 193135 22 193147 34 193158 9 193136 23 193148 35 193159 10 193137 24 193149 36 193160 11 193138 24 193150 37 193161 12 193139 25 193150 38 193162 13 193140 26 193151 39 193163 14 193141 27 193152 40 193164 15 193142 28 193153 41 193165 16 193143 29 193154 42 193219 Steel collets with smooth clamping surface (square) Square Square 7* 192212 20** 192225 8** 192213 21** 192226 9** 192214 22** 192227 10** 192215 23** 192228 11** 192216 24** 192229 12** 192217 25** 192230 13** 192218 26** 192231 14** 192219 27** 192232 15** 192220 28** 192233 16** 192221 29** 192234 17** 192222 30** 192235 18** 192223 19** 192224 Steel collets with smooth clamping surface (hexagonal) Hexagonal Hexagonal 7* 192236 20** 192249 8** 192237 21** 192250 9** 192238 22** 192251 10** 192239 23** 192252 11** 192240 24** 192253 12** 192242 25** 192254 13** 192242 26** 192255 14** 192243 27** 192256 15** 192244 28** 192257 16** 192245 29** 192258 17** 192246 30** 192259 18** 192247 31** 192260 19** 192248 32** 192261 16 technical subject to change
Soft steel collets (pre-bored) 5 192262 15 192263 30 192264 Boring ring 42 for soft steel collets 193399 chuck heads type size 65 Steel collets with axial and radial grooves (*smooth, **radial grooves - round) 5* 92265 18 192278 6* 19226 19 192279 7* 192267 20 192280 8** 192268 21 192281 31 32 33 34 Spannzange Typ Gr. 65 192291 192292 192293 192294 44 192304 57 192317 45 192305 58 192318 46 192306 59 192319 47 192307 60 192320 9** 192269 22 192282 35 192295 48 192308 61 192321 10** 192270 23 192283 36 192296 49 192309 62 192322 11 192271 24 192284 37 192297 50 192310 63 192323 12 192272 25 192285 38 192298 51 192311 64 192324 13 192273 26 192286 39 192299 52 192312 65 192325 14 192274 27 192287 40 192300 53 192312 15 192275 28 192288 41 192301 54 192314 16 192276 29 192289 42 192302 55 192315 17 192277 30 192290 43 192303 56 192316 - - - - Steel collets with smooth clamping surface (round) 5 92265 18 193179 31 193185 44 193196 57 193195 6 192266 19 193180 32 192684 45 193197 58 193209 7 192267 20 193181 33 193186 46 193198 59 193210 8 193172 21 193182 34 193187 47 193199 60 193211 9 193173 22 193183 35 193188 48 193200 61 193212 10 192682 23 193183 36 193189 49 193201 62 193213 11 193174 24 193170 37 193190 50 193202 63 193214 12 192787 25 193065 38 193191 51 193203 64 193215 13 193175 26 193184 39 193192 52 193204 65 193216 14 193276 27 193066 40 192685 53 193205 15 193177 28 193068 41 193193 54 193206 16 193169 29 193069 42 193194 55 193207 17 193178 30 193070 43 193171 56 193208 - - - - Steel collets with smooth clamping surface (square) Square Square Square 8** 192326 21** 192339 34** 192352 9** 192370 22** 192340 35** 192353 10** 192328 23** 192341 36** 192354 11** 192329 24** 192342 37** 192355 12** 192330 25** 192343 38** 192356 13** 192331 26** 192344 39** 192357 14** 192332 27** 192345 40** 192358 15** 192333 28** 192346 41** 192359 16** 192334 29** 192347 42** 192360 17** 192335 30** 192348 43** 192362 18** 192336 31** 192349 44** 192362 19** 192337 32** 192350 45** 192363 20** 192338 33** 192351 46** 192364 Steel collets with smooth clamping surface (hexagonal) Hexagonal Hexagonal Hexagonal Hexagonal 10** 192365 23** 192378 36** 192391 49** 192404 11** 192366 24** 192379 37** 192392 50** 192405 12** 192367 25** 192380 38** 192393 13** 192368 26** 192381 39** 192394 14** 192369 27** 192382 40** 192395 15** 192370 28** 192383 41** 192396 16** 192371 29** 192384 42** 192397 17** 192372 30** 192385 43** 192398 18** 192373 31** 192386 44** 192399 19** 192374 32** 192387 45** 192400 20** 192375 33** 192388 46** 192401 21** 192376 34** 192389 47** 192402 22** 192377 35** 192390 48** 192403 Soft steel collets (pre-bored) 8 192406 20 192407 40 192408 Boring ring 65 for soft steel collets - - - - - - - - - - 193400 - - - - - - - - - - - - technical subject to change 17
Jacobs rubber flex collets Typ F48 / F66 Type / F48 Diameter 5900226 7-9 5900227 9-11 5900228 11-13 59002269 13-15 5900230 15-17 5900231 17-19 5900232 19-21 5900233 21-23 5900234 23-25 5900235 25-27 5900236 27-29 5900237 29-31 5900238 31-33 5900239 33-35 5900666 35-37 5900240 37-39 5900241 39-41 5900242 41-43 Type / F66 Diameter 5900701 19-21 5900702 21-23 5900708 23-25 5900703 25-27 5900704 27-29 5900705 29-31 5900706 31-33 5900707 33-35 5900243 35-37 5900244 37-39 5900245 39-41 5900246 41-43 5900247 43-45 5900248 45-47 5900249 47-49 5900250 49-51 5900251 51-53 5900252 53-55 5900253 55-57 5900254 57-59 5900255 59-61 stop bar spindle stop (Rivelica) The stop can easily be used in any spindle if it is the right size. Sturdy design. With removable locking key Spindle- 19-24 24-33 32-41 41-52 51-62 62-82 73-93 93-117 124-146 181924 232433 283241 384152 485162 586282 707393 8393117 108124146 18 technical subject to change
collet stop The stop can easily be adapted to suit any collet of the same type. Robust design, without easily breakable expansion sleeve. Stop pin can be replaced. Type W12 W20 W25 B32 F35 F38 F48 F66 chucking capacity (mm) 8-9 13.5-15.35 16.5-19.95 23-25 27.6-31 30-34 39.8-45 59-63 custom-made products to meet specific requirements We are happy to go into customer requests in our workshop. We will design and produce for you customised collet chucks according to your ideas. Manual or power operation power operation pressure collet-chuck F27 power operation drawback collet chuck B45 ER-25 technical subject to change 19
FN NIEDERHAUSER AG Bahnhofstrasse 2 CH - 6048 Horw phone 0041 / (0)41 340 50 75 / fax 0041 / (0)41 340 50 74 info@niederhauser.ch / www.niederhauser.ch