Series A Installation, Maintenance and Operating Instructions

Control Valves AU : Angle pattern - Unbalanced Single Seated, Top Guide AB : Angle pattern - Balanced Single Seated, Cage Guide AM : Angle pattern - Omega, Multistage trim Series A Installation, Maintenance and Operating Instructions 4 GV 73 en 2/2017

2 4 GV 73 en Table of Contents 1 GENERAL...3 1.1 Scope of the manual...3 1.2 Valve construction...3 1.3 Valve markings...3 1.4 Technical specifications...3 1.5 Valve seat leakage class...4 1.6 Recycling and disposal...4 1.7 Safety precautions...4 2 TRANSPORTATION, RECEPTION AND STORAGE...4 3 VALVE INSTALLATION...5 3.1 General...5 3.2 Installation into the pipeline...5 3.3 Control valve assembly...5 3.4 Valve insulation...5 4 MAINTENANCE...6 4.1 General...6 4.2 Gland packing adjustment...6 4.3 Replacing the gland packing...6 4.4 Replacing the trim and body reassembly...7 4.5 Pilot Plug...7 5 TESTING THE VALVE... 8 6 REMOVAL & MOUNTING THE ACTUATOR...10 7 TOOLS... 11 8 ORDERING SPARE PARTS...11 9 EXPLODED VIEW AND PARTS LIST...12 10 DIMENSIONS AND WEIGHTS...15 10.1 Valve AU, AB, AM... 15 10.2 Actuators VD, VC... 16 11 TYPE CODE...19 READ THESE INSTRUCTIONS FIRST! These instructions provide information about safe handling and operation of the valve. If you require additional assistance, please contact the manufacturer or manufacturer's representative. Addresses and phone numbers are printed on the back cover. SAVE THESE INSTRUCTIONS! Subject to change without notice. All trademarks are property of their respective owners. This product meets the requirements set by the Customs Union of the Republic of Belarus, the Republic of Kazakhstan and the Russian Federation.

4 GV 73 en 3 1 GENERAL 1.1 Scope of the manual This manual provides essential information on series A, AU: Angle pattern-unbalanced single seated, AB: Angle pattern-balanced single seated, AM: Angle pattern-omega multistage trim installed sliding stem valves. Actuators and positioners are only discussed briefly. Refer to the individual manuals for further information on their installation, operation and maintenance. 1.2 Valve construction Series AU, Angle-Unbalanced valves are flanged (weld end available) single seated sliding stem control valves. The valve seat ring and retainer and plug with stem is a module accessible through the bonnet opening (top entry) of the body. The standard design provides a top guide with a contoured plug with a quick change seat ring. The solid top (retainer) plug boss guiding makes strong support to ensure valve alignment. This series are available to provide a series of reduced bore trim and the standard seat tightness is class IV, optional trims can meet to class V and VI, ANSI/FCI 70.2. Series AB, Angle-Balanced cage guide valves are flanged (weld end available) single seated sliding stem control valves. The valve seat ring and cage and plug with stem is a module accessible through the bonnet opening (top entry) of the body. The standard design provides a cage guide with a piston type plug with a quick change seat ring. The two split cages and inserted plug seal ring makes strong support to ensure valve alignment. This series is available with series of reduced Cv trims and the standard seat tightness is class III~IV, optional trims can meet to class V, ANSI/FCI 70-2. Series AM, Angle-Omega, multistage trim installed valves are flanged (weld end available) single seated sliding stem control valves. The valve seat ring and cage and plug with stem is a module accessible through the bonnet opening (top entry) of the body. The standard design provides a cage guide with a piston type plug with a quick change seat ring. The two split cages (cage guide and cage) and inserted plug seal ring makes strong support to ensure valve alignment. For few cases in very small rated Cv, applicable unbalanced contoured trim in this series. This series is available with series of reduced Cv trims and the standard seat tightness is class III~IV, optional trims can meet to class V, ANSI/FCI 70-2. The detailed structure is revealed by the type code shown on the valve identification plate. The type code is explained in Section 11. NOTE: Selection and use of the valve in a specific application requires close consideration of detailed aspects. Due to the nature of the product, this manual cannot cover all the individual situations that may occur when the valve is used. If you are uncertain about use of the valve or its suitability for your intended purpose, please contact Metso for more information. For valves in oxygen service, please see also the separate installation, maintenance and operating instructions for oxygen service (see Metso document id:10o270en.pdf). Fig. 1 Construction of a Neles A series Single Seated Valve 1.3 Valve markings The body markings are: manufacturer's trademark, nominal size, pressure rating and material of the body. The valve has an identification plate attached to it, see Fig. 2. Fig. 2 Markings on the identification plate: 1. Type designation (Valve code) 2. Size, Rating 3. Cv 4. Body material 5. Plug, Stem material 6. Seat material 7. Temp. min./max. 8. Maximum (shut-off) pressure 9. Valve manufacturing date 10. Tag No. 11. Serial No. 1.4 Technical specifications Face-to-face length: ANSI/ISA-75.08.01, 03, 05 & ANSI/ISA-75.08.06 (Long) Body rating: Class 150 to Class 4500 PN 10 to PN 450 Max. pressure differential: Temperature range: Flow direction: Identification (name) plate example Actuator mounting: Stem connection: Dimensions: see Section 10 Weights: see Section 10 acc. to pressure class -196 to +593 C (depending on the body materials and bonnet type) indicated by an arrow on the body (normally flow to open) threaded bonnet with yoke nut or bolted yoke clamp with bolts/nuts

4 4 GV 73 en Note that the max. shut-off pressure is based on the mechanical maximum differential pressure at ambient temperature. You must always observe the fluid temperature when deciding on applicable pressure values. When selecting a valve you must also check the noise level, cavitation intensity, flow velocity, actuator load factor, etc. using Nelprof. 1.5 Valve seat leakage class The valve follows the seat leakage classifications of ANSI/ FCI 70-2 requirement. 1.6 Recycling and disposal Most valve parts can be recycled if sorted according to material. Most parts have a material marking. A material list is supplied with the valve. In addition, separate recycling and disposal instructions are available from the manufacturer. A valve can also be returned to the manufacturer for recycling and disposal for a fee. 1.7 Safety precautions Do not exceed the valve performance limitations! Exceeding the limitations marked on the valve may cause damage and lead to uncontrolled pressure release. Damage or personal injury may result When handling the valve or the control valve assembly, take its weight into account! Never lift the valve or control valve assembly by the positioner, the limit switch or their piping. Place the lifting ropes securely around the valve body (see Fig. 3). Damage or personal injury may result from falling parts. Follow the proper procedures when handling and servicing Oxygen valves. 2 TRANSPORTATION, RECEPTION AND STORAGE Check the valve and the accompanying devices for any damage that may have occurred during transport. Store the valve carefully before installation, preferably indoors in a dry place. Do not dismantle the valve or remove it from the pipeline while the valve is pressurised! Dismantling or removing a pressurised valve will result in uncontrolled pressure release. Always isolate the relevant part of the pipeline, release the pressure from the valve and remove the medium before dismantling the valve. Be aware of the type of medium involved. Protect yourself and the environment from any harmful or poisonous substances. Make sure that no medium can enter the pipeline during valve maintenance. Failure to do this may result in damage or personal injury. Beware of the plug movement! Keep fingers, other parts of the body, tools and other objects out of the open flow port. Leave no foreign objects inside the pipeline. When the valve is actuated, the plug functions as a cutting device. Close and detach the actuator pressure supply pipeline for valve maintenance. Failure to do this may result in damage or personal injury. Protect yourself from noise! The valve may produce noise in the pipeline. The noise level depends on the application. It can be measured or calculated using the Metso Nelprof software. Observe the relevant working environment regulations in terms of noise emission. Beware of a very cold or hot valve! The valve body may be very cold or very hot during use. Protect yourself against cold injuries or burns. Fig. 3 Lifting the valve NOTE : *. Only acceptable case-4, when lift and move the valves; 1) up to 10"- 300# body with VD (Diaphragm type) actuators 2) up to 12"- 300# body with VC (Cylinder type) actuators In the above two cases the lifting is limited to max. height of 1.0 m and max. moving distance of 70 m. Do not remove the flow port protectors until immediately before installation of the valve into the pipeline. The valve is delivered in the closed position. Valve equipped with a spring-return actuator is delivered in the position determined by the spring.

4 GV 73 en 5 3 VALVE INSTALLATION 3.1 General Remove the flow port protectors and check that the valve is clean inside. When handling the valve or the control valve assembly, take its weight into account! 3.2 Installation into the pipeline 3.2.1 Pipeline cleaning Make sure no foreign particles, such as sand or pieces of welding electrode, are in the pipeline, they may damage the sealing surfaces. 3.2.2 Installation valve The valve has an arrow indicating the flow direction. Install the valve in the pipeline so that the flow direction of the valve corresponds to the flow direction marked on the pipe. The mounting orientation of the valve should be vertical position as it is shown on Fig.4. NOTE: For any other mounting position, please consult the factory. Choose flange gaskets according to the operating conditions. Do not attempt to correct a pipeline misalignment by means of flange bolting. Loads on the valve body from pipeline vibrations can be reduced by supporting the pipeline properly. Reduced vibration also increases the lifetime of the positioner. Where necessary, you can support the valve by the body, using regular pipe clamps and supports. Do not fasten supports to the valve or flange bolting or to the actuator, see Fig. 4. Fig. 4 Installing the control valve into pipeline using supports Do not attempt to correct a pipeline misalignment by means of flange bolting. Loads on the valve body from pipeline vibrations can be reduced by supporting the pipeline properly. Reduced vibration also increases the lifetime of the positioner. Where necessary, you can support the valve by the body, using regular pipe clamps and supports. Do not fasten supports to the valve or flange bolting or to the actuator, see Fig. 4. 3.3 Control valve assembly Check all joints, piping and cables. Check that the actuator stop screws, positioner and limit switches are calibrated. Refer to their installation, maintenance and operating manuals. 3.4 Valve insulation If necessary, the valve may be insulated. Insulation must not continue above the upper level of the valve body, see Fig. 5. 3.2.3 Hydrostatic testing and Line flushing When the line is hydrostatic test and flushing, the control valve should not used as an isolating valve. Make sure the control valve always be opened position before start this process. Otherwise valve and trim damage or failure of the seals could result. Flushing and hydrostatic test kit can be purchased from Metso. Flushing trim kit sholud be installed in the valve (especially 'Tendril & Omega trim' application) to protect the original trim and the flow passages while the valve installation and line flushing. Unless this caution could result in clogging trim, low flow rates, unstable control, valve leakage and exessive noise Fig. 5 Insulation of the valve

6 4 GV 73 en 4 MAINTENANCE Observe the safety precautions listed in Section 1.7 before starting work! 4.3 Replacing the gland packing Do not dismantle the valve or remove it from the pipeline while the valve is pressurised! When handling the valve or the control valve assembly, take its weight into account! 4.1 General The Neles A series angle valves require no regular maintenance. However, check the gland packing for leakage. This section outlines the maintenance that can be carried out by the user. The numbers in parentheses refer to the parts lists and the exploded views of the valve in Section 9. NOTE: If you send the valve to the manufacturer for repair, do not dismantle it. Clean the valve carefully, including the inside. For safety reasons, inform the manufacturer of the nature of the medium when you send the valve. Fig. 6 Gland packing NOTE: Always use original spare parts to make sure the valve functions as intended. 4.2 Gland packing adjustment In the event of a packing leakage tighten the hexagon nuts (18) in ¼ turn steps each until the leakage is stopped. Do not tighten more than necessary. Make sure the valve is not pressurised. Remove the actuator from the valve stem according to the instructions given in the actuator manual. Loosen and remove the hexagon nuts (18). Remove the gland flange (9b), and gland (9a) up to the valve stem. Remove the old packing rings (69) using a pointed tool, avoid damaging the seal surfaces and valve stem. Clean the packing ring counterbore. Mount the new packing rings one by one into the packing gland box using the gland as a tool and mount the gland with hand-tightened nuts. Fasten the gland with the hexagon nuts (18) and tighten them. Check leakage when the valve is pressurised. 14 14 14 9b 18 9b 18 9b 18 9a 69 3 9a 69 3 9a 69 3 21 8 21 21 22 22 8 22 8 13 13 13 17 19 19a 17 19 19a 17 19 19a 5 5 5 6 65 16 65 16 65 4 6 6 15 78 10 3 3 3 7 7 7 63 63 63 1 1 1 AU: Angle - Unbalanced AB: Angle - Balanced AM: Angle - Omega Fig. 7 Neles A Series Angle Pattern - Globe Valves

4 GV 73 en 7 Valve Size Bonnet Stud Bolts mm in Rating (ANSI) Size Q`ty 4.4 Replacing the trim and body reassembly 50 2 80 3 100 4 150 6 200 8 250 10 300 12 350 14 400 16 Required Torques (± 5 % allowable) Carbon Steel St. Steel Bolts Bolts Nm lbf ft Nm lbf ft 150-300 1/2"-13UNC 8 101 74 80 59 600 1/2"-13UNC 8 158 116 123 90 900 7/8"-9UNC 8 199 146 1500 7/8"-9UNC 8 286 210 199 146 150-300 3/4"-10UNC 8 176 129 600 3/4"-10UNC 8 211 155 900 1-1/8"-8UNC 8 558 409 136 100 1500 1-1/8"-8UNC 8 792 581 150-300 7/8"-9UNC 8 222 163 600 7/8"-9UNC 8 327 240 900 1-1/4"-8UNC 8 867 633 160 118 1500 1-1/4"-8UNC 8 1339 982 150-300 1"-8UNC 8 316 232 600 1"-8UNC 12 327 240 291 214 900 1-1/2"-8UNC 12 1192 874 1500 1-1/2"-8UNC 12 1456 1068 942 691 150-300 1-1/4"-8UNC 8 478 351 478 351 600 1-1/4"-8UNC 12 653 479 653 479 900 1-5/8"-8UNC 12 1676 1229 1500 1-5/8"-8UNC 12 1870 1372 1140 836 150-300 1-1/4"-8UNC 12 486 356 486 356 600 1-1/4"-8UNC 16 909 667 900 1-3/4"-8UNC 12 2059 1510 716 525 150-300 1-1/2"-8UNC 12 729 535 600 1-1/2"-8UNC 12 1317 966 729 535 900 1-1/2"-8UNC 16 1408 1032 150-300 1-1/2"-8UNC 12 875 642 600 1-1/2"-8UNC 12 1581 1160 875 642 900 1-1/2"-8UNC 16 1689 1238 150-300 1-1/2"-8UNC 12 1529 1121 600 1-1/2"-8UNC 16 1426 1046 980 719 NOTE: The trim set consists of the seat ring, valve plug and stem, retainer and gaskets (for seat ring and bonnet). Make sure the valve is not pressurised. Remove the actuator from the valve stem according to the instructions given in the actuator manual and next Section 6. Remove the hexagon nuts (18) slightly. Remove the hexagon nuts (17). Remove the bonnet (8) Remove the one unit of stem and plug (5 & 3) with the retainer (10) in case of AU. * Remove the stem and plug (5 & 3) in case of AB & AM. * Remove the cage guide (16), cage (15) and the seal ring (64). Avoid from damaging the seal ring between the cage and cage guide in case of AB & AM. Remove the body gasket (65), seat ring(7), seat gasket(63) Do not reuse the spiral wound gaskets (63 & 65), this is need to be replace each time the valve is disassembled. Remove the hexagon nuts (18), gland flange (9b) and gland (9a) Remove the old packing rings (69) NOTE: If the valve have excess leakage, the plug and seating surface need lapping and cleaning. NOTE: Guide Bushing Removal (AU) The Retainer Guide Bushing (4) is a press and tag welded fit into the retainer and does not normally necessary replacement. If need, it may be machined out. When machining the bushing out, care must be maintain proper dimensions and tolerances. NOTE: Omega multi stage Cage Cleaning (AM) The welded Omega multi stage cage is not available disassembling, make sure the ultrasonic cleaning in the frequency range of 250 ~ 400 khz and Min. duration 60 min. Clean the body gasket surface. Insert a new seat gasket (63) and the seat ring (7) into the body. Install the valve plug and stem assembly (3 & 5) with the retainer (10) very carefully in case of AU. Install the cage (15), seal ring (64), cage guide (16) and plug stem assembly (3, 5, 6) very carefully in case of AB & AM. Insert the body gasket (65). Mount the bonnet on the body carefully maintaining alignment with the plug and the stem and with the retainer (or cage) in the closed position, so that the arrow on the body and on the bonnet point in the same direction. Insert the hexagon nuts (17) into stud (13) and slightly fasten the nuts. Do not strongly tighten stud nuts at this time Insert the packing ring (69) according to above 4.3 The all related parts (seat ring, retainer, cage, plug & stem, bonnet) must be properly aligned in the body. Tighten hexagon nuts (17) until plug and seat contact is obtained with proper bolt torque. 4.5 Pilot Plug Disassembly & Assembly Mount the plug and stem assembly on the chuck to setting. Remove the pilot wire (76). Remove the pilot bolts (75). Make sure to balance when loose the pilot bolts, and be careful the spring tension to bounced off the pilot plug and stem. Remove the pilot cover (74). Remove the pilot plug (73) and pilot stem (72) from pilot main plug (71). Remove the pilot spring (77) carefully. Remove the pilot plug (73) and the pilot seat as well as the surface inside of the pilot main plug (71). If there is damage, scratches or grooves, it should be replaced or repaired.

8 4 GV 73 en Insert the cleaned pilot spring (77) into the upper side of main plug. Install the pilot plug (73) & stem (72) on the spring (77). Install the pilot cover (74) and fasten the pilot bolts (75) keep in balance. Install wire (76) for connecting the all pilot bolts due to prevent loose on operation. 5 TESTING THE VALVE Pressure testing should be carried out using equipment conforming to the correct pressure class! We recommend that the valve body is pressure-tested after the valve has been assembled. The pressure test should be carried out in accordance with an applicable standard for the pressure rating. The valve must be in the open position during the test. Fig. 8 Pilot Cage-Balance Trim Different trim designs AU, Standard contoured trim AU, Tendril trim AU, Soft seat trim AU, Micro trim AU, Multi-groove Fig. 9 Different trim designs (AU series)

4 GV 73 en 9 Different trim designs AB, Quick change, standard cage trim AB, Tendril Multi-hole trim AB, Tendril Multi-stage trim AB, Pilot balanced trim AB, Pilot balanced trim, Tendril 1-stage with diffuser Fig. 10 Different trim designs (AB series) Different trim designs AM, Standard balanced trim AM, Pilot balanced trim Fig. 11 Different trim designs (AM series)

10 4 GV 73 en 6 REMOVAL & MOUNTING THE ACTUATOR The actuator is attached to the valve according to the manual for actuator with body assembly and plug stem adjustment. Several types of Metso actuators can be used with suitable clamps. Refer to the model VD springdiaphragm and VC double acting cylinder actuator manuals for further information on their installation, maintenance and operation. Beware of the plug movement! Do not use air pressure higher than what specified on the identification plate. A. Actuator removal for Reverse <air to open, stem retract> actuator (Fig. 12) Lift up to the valve plug 100% from the seat ring, using by specified air pressure. Loosen the stem lock nut (5**) and socket head screws (1a**) and hexagon nuts (1b**) Remove the clamp (1**) Shut off and disconnect air supply line. Support actuator with the suitable lifting device. Remove the yoke nut. Remove the actuator from the valve body assembly. B. Actuator replacement (mounting) for Reverse <air to open, stem retract> actuator (Fig. 12) Mount the new or repaired actuator on top of the bonnet, using a suitable lifting device. Insert the yoke nut and tightly fasten the yoke by turning the yoke nut clockwise using tightening tools. Connect air line and accessories. Lift the top stem (18), using by specified air pressure. Adjustment stem length after clamping the clamp (1**) according to rated travel(stroke) as open and close position as per pressurizing and depressurizing the lower diaphragm chamber. Tighten stem socket head screws (1a**) and hexagon nuts (1b**) with stem lock nut (5**). C. Actuator removal for Direct <air to close, stem extend> actuator (Fig. 12) Shut off and disconnect the air supply lines and accessories. Loosen stem lock nut (5**) and stem socket head screws (1a**) and hexagon nuts (1b**) Remove the clamp (1**) Support actuator with the suitable lifting device. Remove the yoke nut (3**). Remove the actuator from the valve body assembly. D. Actuator replacement (mounting) for Direct <air to close, stem extend> actuator (Fig. 12) Mount the new or repaired actuator on top of the bonnet, using a suitable lifting device to setting. Insert the yoke nut and tightly fasten the yoke by turning the yoke nut clockwise using tightening tools. Connect air line and accessories. Down the top stem (18), using by specified air pressure. Adjust stem length after clamping stem clamp according to rated travel (stroke) as open and close position as per pressurizing and depressurizing the upper diaphragm chamber. Tighten stem socket head screws (1a**) and hexagon nuts (1b**) with stem lock nut (5**). E. Type VC Springless Cylinder, Double Acting Actuator This actuator is springless cylinder, double acting actuator, can use the 3/8, 1/2 NPT port according to specified on the data sheet for all air lines. Refer to the model VC double acting cylinder actuator manuals for further information on their installation, maintenance and operation. Avoid to turn the valve plug and stem when plug is on seat ring to prevent the seating line from being damaged.

4 GV 73 en 11 7 TOOLS Removal of the actuator L- wrench set (mm) hex socket wrench set chisel and hammer (10 pound) +,- drivers 8 ORDERING SPARE PARTS NOTE: Always use original spare parts to make sure that the valve functions as intended. When ordering spare parts, always include the following information: type code, sales order number, serial number number of the parts list, part number, name of the part and quantity required This information can be found from the identification plate or documents. Direct Action actuator (Air to Close, stem extend) Reverse Action actuator (Air to Open, stem retract) VD Actuator part 1. YOKE 10. LOWER CASE 18 TOP STEM 20. UPPER CASE 21. LIFTING EYE NUT 22. WASHER 23. HEXAGON SCREW 24. HEXAGON SCREW 25. HEXAGON NUT 30. IDENTIFICATION PLATE 32. INDICATOR 32a. ROUND HEAD SCRREW 34. VENT CAP 99. AIR SUPPLY PORT V-A (Valve-Actuator) Mounting Part (**) 1** CLAMP 1a**SOCKET HEAD SCREW 1b** HEXAGON NUT 3**YOKE NUT (see above VD fig.) 5** STEM LOCK NUT 6** LOCK WASHER Fig. 12 VD Actuator

12 4 GV 73 en 9 EXPLODED VIEW AND PARTS LIST AU 65 4 10 5 3 6 7 63 3 ** 18 14 9b 9a 69 21 69 67 17 13 8 1 4 Item Description Recommended spare part 1 BODY 2* PLUG SET 3* PLUG 5* STEM 6* PLUG PIN 3** YOKE NUT 4 GUIDE BUSHING 7 SEAT RING 8 BONNET 9a GLAND 9b GLAND FLANGE 10 RETAINER 12 DISK SPRING ASS'Y 13 STUD 14 STUD 17 HEXAGON NUT 18 HEXAGON NUT 19 IDNTIFICATION PLATE 19A RIVET 21 LANTERN RING 63 SEAT GASKET X 65 BODY GASKET X 67 PACKING SPACER 69 PACKING RING X ) Delivered as a set **) V-A Mounting Parts

4 GV 73 en 13 AB 65 5 6 3 16 64 15 7 63 3 ** 18 14 9b 9a 69 21 69 67 17 13 8 1 Item Description Recommended spare part 1 BODY 2* PLUG SET 3* PLUG 5* STEM 6* PLUG PIN 3** YOKE NUT 7 SEAT RING 8 BONNET 9a GLAND 9b GLAND FLANGE 12 DISK SPRING ASS'Y 13 STUD 14 STUD 15 CAGE 16 CAGE GUIDE 17 HEXAGON NUT 18 HEXAGON NUT 19 IDNTIFICATION PLATE 19A RIVET 21 LANTERN RING 63 SEAT GASKET X 64 SEAL RING X 65 BODY GASKET X 67 PACKING SPACER 69 PACKING RING X 71 PILOT MAIN PLUG 73 PILOT PLUG 74 PILOT COVER 75 PILOT BOLT 76 PILOT WIRE 77 PILOT SPRING ) Delivered as a set **) V-A Mounting Parts

14 4 GV 73 en AM 65 5 3 6 16 64 15 15 15 15 7 3 ** 18 14 9B 9a 69 21 69 67 17 13 8 63 1 Item Description Recommended spare part 1 BODY 2* PLUG SET 3* PLUG 5* STEM 6* PLUG PIN 3** YOKE NUT 7 SEAT RING 8 BONNET 9a GLAND 9b GLAND FLANGE 12 DISK SPRING ASS'Y 13 STUD 14 STUD 16 CAGE GUIDE 17 HEXAGON NUT 18 HEXAGON NUT 19 IDNTIFICATION PLATE 19A RIVET 21 LANTERN RING 25 DISK STACK 63 SEAT GASKET X 64 SEAL RING X 65 BODY GASKET X 67 PACKING SPACER 69 PACKING RING X 71 PILOT MAIN PLUG 73 PILOT PLUG 74 PILOT COVER 75 PILOT BOLT 76 PILOT WIRE 77 PILOT SPRING ) Delivered as a set **) V-A Mounting Parts

4 GV 73 en 15 10 DIMENSIONS AND WEIGHTS 10.1 Valve AU, AB, AM DRILLING Dia. of Hole = F Pitch Circle Dia. = G No of Holes = H EXTENSION BONNET 150 # / 300 # / 600 # Dimension A B C D E F G H Weight (kg) Size 150# 300# 600# 150# 300# 600# STD EXT COMMON 150# 300# 600# 150# 300# 600# 150# 300# 600# 150# 300# 600# 150# 300# 600# 1" 92 99 105 92 99 105 142 250 110 110 125 125 15.9 19.1 19.1 79.4 88.9 88.9 4 4 4 14 15 23 1-1/2" 111 118 126 111 118 126 161 295 110 125 155 155 15.9 22.2 22.2 98.4 114.3 114.3 4 4 4 22 23 27 2" 127 134 143 127 134 143 178 295 110 150 165 165 19.1 19.1 19.1 120.7 127 127 4 8 8 25 27 32 3" 149 159 169 149 159 169 222 330 115 190 210 210 19.1 22.2 22.2 152.4 168.3 168.3 4 8 8 65 67 72 4" 176 184 197 176 184 197 248 380 140 230 255 275 19.1 22.2 25.4 190.5 200 215.9 8 8 8 100 103 112 6" 226 237 254 226 237 254 340 430 150 280 320 355 22.2 22.2 28.6 241.3 269.9 292.1 8 12 12 185 195 240 8" 272 284 305 272 284 305 451 490 150 345 380 420 22.2 25.4 31.8 298.5 330.2 349.2 8 12 12 363 385 443 10" 337 354 376 337 354 376 488 600 150 405 445 510 25.4 28.6 34.9 362 387.4 431.8 12 16 16 552 595 681 12" 369 388 410 369 388 410 543 660 150 485 520 560 25.4 31.8 34.9 431.8 450.8 489 12 16 20 905 955 1020 14" 445 464 486 445 464 486 616 740 210 535 585 605 28.6 31.8 38.1 476.3 514.4 527 12 20 20 1170 1230 1311 16" 508 529 554 508 529 554 692 820 220 595 650 685 28.6 34.9 41.3 539.8 571.5 603.2 16 20 20 1380 1460 1587 900 # / 1500 # Dimension A B C D E F G H Weight (kg) Size 900# 1500# 900# 1500# STD EXT COMMON 900# 1500# 900# 1500# 900# 1500# 900# 1500# 900# 1500# 1" 146 146 146 146 229 330 110 150 150 25.4 25.4 101.6 101.6 4 4 44 46 1-1/2" 167 167 167 167 278 380 110 180 180 28.6 28.6 123.8 123.8 4 4 63 63 2" 188 188 188 188 300 400 110 215 215 25.4 25.4 165.1 165.1 8 8 67 67 3" 221 230 221 230 330 430 115 240 265 25.4 31.8 190.5 203.2 8 8 150 163 4" 256 265 256 265 350 450 140 290 310 31.8 34.9 235 241.3 8 8 244 255 6" 357 384 357 384 393 500 150 380 395 31.8 38.1 317.5 317.5 12 12 530 540 8" 457 486 457 486 480 600 150 470 485 38.1 44.5 393.7 393.7 12 12 698 821 10" 496 534 496 534 518 650 150 545 585 38.1 50.8 469.9 482.6 16 12 955 1137 12" 565 610 565 610 680 800 150 610 675 38.1 54 533.4 571.5 20 16 1180 1240 14" 629 629 629 629 770 920 210 640 750 41.3 60.3 558.8 635 20 16 1387 1477 16" 711 711 711 711 850 1050 220 705 825 44.5 66.7 616 704.8 20 16 1601 1721

16 4 GV 73 en 10.2 Actuators VD, VC VDD Direct Action VDR Reverse Action D A2 A2 Ed Er C2 C2 Bd Br Without handwheel Size A2 Bd Br D Ed Er C2 Weight(kg) 25 255 348 373 NPT 1/4 149 124 225 12 29 295 391 416 NPT 1/4 174 129 251 18 37 375 464 489 NPT 1/4 184 128 284 28 48 486 652 677 NPT 1/4 250 165 381 86 55 566 695 720 NPT 1/4 260 156 381 112 NOTE 1. 'Br' refers to reverse acting actuator, VDR 2. 'Bd" refers to direct actina actuator, VDD VDD Direct Action VDR Reverse Action D A2 A3 A2 A3 B hd B hr C2 C2 Bd B r (UNIT:mm) With handwheel Size A2 Bd Br D A3 Bhd Bhr C2 Weight(kg) 25 255 348 373 NPT 1/4 312 110 170 225 22 29 295 391 416 NPT 1/4 312 122 182 251 28 37 375 464 489 NPT 1/4 342 141 201 284 43 48 486 652 677 NPT 1/4 464 144 244 381 119 55 566 695 720 NPT 1/4 464 144 244 381 145 NOTE 1. 'Br" refers to reverse actina actuator, VDR 2. 'Bd' refers to direct actina actua1or, VDD

4 GV 73 en 17 Size # 30 Stroke A Weight B1 D1 (kg) ØC E F B2 D2 A B Size # 40 Stroke A Weight B1 D1 (kg) ØC E F B2 D2 A B Size # 50 Stroke A Weight B1 D1 (kg) ØC E F B2 D2 A B 640 185 40 145 Ø370 760 305 420 PT 1/2 92 115 650 195 50 145 Ø370 790 335 420 PT 1/2 94 118 660 205 60 145 Ø370 820 365 420 PT 1/2 97 121 370 215 70 145 Ø370 850 395 420 PT 1/2 100 124 680 225 80 145 Ø370 880 425 420 PT 1/2 103 127 690 235 90 145 Ø370 910 455 420 PT 1/2 106 130 700 245 100 145 Ø370 940 485 420 PT 1/2 108 133 720 265 120 145 Ø370 1000 545 420 PT 1/2 114 139 810 205 40 145 Ø460 935 330 560 PT 1/2 120 148 820 215 50 145 Ø460 965 360 560 PT 1/2 123 152 830 225 60 145 Ø460 995 390 560 PT 1/2 126 155 840 235 70 145 Ø460 1025 420 560 PT 1/2 128 159 850 245 80 145 Ø460 1055 450 560 PT 1/2 131 162 860 255 90 145 Ø460 1085 480 560 PT 1/2 137 166 870 265 100 145 Ø460 1115 510 560 PT 1/2 142 177 890 285 120 145 Ø460 1175 570 560 PT 1/2 142 177 910 305 140 145 Ø460 1235 630 560 PT 1/2 148 184 950 345 180 145 Ø460 1355 750 560 PT 1/2 159 198 810 205 40 145 Ø560 935 330 560 PT 1/2 186 234 820 215 50 145 Ø560 965 360 560 PT 1/2 189 237 60 145 830 Ø560 225 995 390 560 PT 1/2 192 242 840 235 70 145 Ø560 1025 420 560 PT 1/2 195 246 850 245 80 145 Ø560 1055 450 560 PT 1/2 198 251 860 255 90 145 Ø560 1085 480 560 PT 1/2 201 256 870 265 100 145 Ø560 1115 510 560 PT 1/2 203 261 890 285 120 145 Ø560 1175 570 560 PT 1/2 209 270 910 305 140 145 Ø560 1235 630 560 PT 1/2 215 279 950 345 180 145 Ø560 1355 750 560 PT 1/2 227 298 Size # 60 Stroke A Weight B1 D1 (kg) ØC E F B2 D2 A B Size # 70 Stroke A Weight B1 D1 (kg) ØC E F B2 D2 A B Size # 80 Stroke A Weight B1 D1 (kg) ØC E F B2 D2 A B 954 264 100 145 Ø660 1199 509 640 PT 1/2 255 344 974 284 120 145 Ø660 1259 569 640 PT 1/2 262 355 994 304 140 145 Ø660 1319 629 640 PT 1/2 269 365 1034 344 180 145 Ø660 1349 749 640 PT 1/2 283 386 1094 404 240 145 Ø660 1619 929 640 PT 1/2 303 417 955 265 100 145 Ø710 1203 510 640 PT 3/4 322 438 975 285 120 145 Ø710 1263 570 640 PT 3/4 330 450 995 305 140 145 Ø710 1323 630 640 PT 3/4 338 461 1035 345 180 145 Ø710 1443 750 640 PT 3/4 354 484 1095 405 240 145 Ø710 1623 930 640 PT 3/4 377 518 954 264 100 145 Ø820 1207 509 640 PT 3/4 378 519 974 284 120 145 Ø820 1267 569 640 PT 3/4 386 531 997 304 140 145 Ø820 1327 629 640 PT 3/4 394 543 1034 344 180 145 Ø820 1447 749 640 PT 3/4 410 567 1094 404 240 145 Ø820 1627 929 640 PT 3/4 435 604 1134 444 280 145 Ø820 1747 1049 640 PT 3/4 451 628

18 4 GV 73 en Size # 30 Weight B1 D1 (kg) Stroke A ØC E F G B2 D2 A B 40 930 185 145 Ø370 1055 305 470 470 PT 1/2 134 157 50 940 195 145 Ø370 1085 335 470 470 PT 1/2 137 160 60 950 205 145 Ø370 1115 365 470 470 PT 1/2 139 163 70 960 215 145 Ø370 1145 395 470 470 PT 1/2 142 167 80 970 225 145 Ø370 1175 425 470 470 PT 1/2 144 170 90 980 235 145 Ø370 1205 455 470 470 PT 1/2 147 173 990 245 100 145 Ø370 1235 485 470 470 PT 1/2 150 176 120 145 1010 265 Ø370 1295 545 470 470 PT 1/2 155 183 Size # 40 Weight B1 D1 (kg) Stroke A ØC E F G B2 D2 A B 40 145 1095 205 Ø460 1220 330 845 616 PT 1/2 180 208 50 145 1105 215 Ø460 1250 360 845 616 PT 1/2 183 212 60 145 1115 225 Ø460 1280 390 845 616 PT 1/2 186 215 70 145 1125 235 Ø460 1310 420 845 616 PT 1/2 188 219 80 145 1135 245 Ø460 1340 450 845 616 PT 1/2 191 222 90 145 1145 255 Ø460 1370 480 845 616 PT 1/2 194 226 100 145 1155 265 Ø460 1400 510 845 616 PT 1/2 197 230 120 145 1175 285 Ø460 1460 570 845 616 PT 1/2 202 237 140 145 1195 305 Ø460 1520 630 845 616 PT 1/2 208 244 180 145 1235 345 Ø460 1640 750 845 616 PT 1/2 219 258 Size # 50 Stroke A Weight B1 D1 (kg) ØC E F G B2 D2 A B 40 145 1095 Ø560 205 845 616 PT 1/2 246 294 1220 330 50 145 1105 Ø560 215 845 616 PT 1/2 249 299 1250 360 60 145 1115 Ø560 225 845 616 PT 1/2 252 303 1280 390 70 145 1125 Ø560 235 845 616 PT 1/2 255 308 1310 420 80 145 1135 Ø560 245 845 616 PT 1/2 258 313 1340 450 90 145 1145 Ø560 255 845 616 PT 1/2 261 318 1370 480 100 145 1155 Ø560 265 845 616 PT 1/2 263 322 1400 510 120 145 1175 Ø560 285 845 616 PT 1/2 269 332 1460 570 140 145 1195 Ø560 305 845 616 PT 1/2 275 341 1520 630 180 145 1235 Ø560 345 845 616 PT 1/2 287 360 1640 750 Size # 60 Stroke A B1 D1 Weight (kg) ØC E F D B2 D2 A B 100 145 1239 Ø660 264 1484 509 925 696 PT 1/2 315 404 120 145 1259 Ø660 284 1544 569 925 696 PT 1/2 322 415 140 145 1279 Ø660 304 1604 629 925 696 PT 1/2 329 425 180 145 1319 Ø660 344 1724 749 925 696 PT 1/2 343 446 240 145 1379 Ø660 404 1904 929 925 696 PT 1/2 363 477 Size # 70 Stroke A B1 D1 Weight (kg) ØC E F D B2 D2 A B 100 145 1240 Ø710 265 1488 510 925 696 PT 3/4 368 502 120 145 1260 Ø710 285 1548 570 925 696 PT 3/4 376 514 140 145 1280 Ø710 305 1608 630 925 696 PT 3/4 384 525 180 145 1320 Ø710 345 1728 750 925 696 PT 3/4 400 548 240 145 1380 Ø710 405 1908 930 925 696 PT 3/4 423 582 Size # 80 Stroke A B1 D1 Weight (kg) ØC E F D B2 D2 A B 100 145 1289 Ø820 264 1542 509 975 696 PT 3/4 438 579 120 145 1309 Ø820 284 1602 569 975 696 PT 3/4 446 591 140 145 1329 Ø820 304 1662 629 975 696 PT 3/4 454 603 180 145 1369 Ø820 344 1782 749 975 696 PT 3/4 470 627 240 145 1429 Ø820 404 1962 929 975 696 PT 3/4 495 664 280 145 1469 Ø820 444 975 696 PT 3/4 511 688 2082 1049

4 GV 73 en 19 11 TYPE CODE Angle Unbalanced, Top Guided Type, Series AU 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. AU 01 C W A J2 X P1 X BC S1 R1 X S G X S A X A L FC VALVE CONSTRUCTIONS 1. VALVE SERIES AU Angle Unbalanced, Top guided type 2. BODY SIZE 01 1" / DN 25 1H 1-1/2" / DN 40 02 2" / DN 50 03 3" / DN 80 Optional body size 04 4" / DN 100 Y 3. PRESSURE RATING C ASME Class 150 D ASME Class 300 F ASME Class 600 4. END CONNECTION W Flanged RF, ASME B16.5 Optional end connection V Socket welding, ASME B16.11 Q Butt welding, ASME B16.25 Z Ring joint flange, ASME B16.5 5. BONNET CONSTRUCTION Bonnet type Actuator connection A Standard Standard actuator size B Standard Applicable for VD_48/55 (3",4" only) Optional bonnet construction E Extension Standard actuator size F Extension Applicable for VD_48/55 (3",4" only) L Bellows seals Standard actuator size M Bellows seals Applicable for VD_48/55 (3",4" only) Special 6. BODY & BONNET MATERIAL J2 A216 gr. WCB S6 A351 gr. CF8M Optional body & Bonnet material S4 A351 gr. CF8 S9 A351 gr. CF3 S1 A351 gr. CF3M Y 7. BEARINGS (TRUNNION / THRUST BEARING) X Not applicable TRIM CONSTRUCTIONS 8. PLUG MATERIAL Material Description P1 410 SS Standard for carbon steel body T6 316 SS Standard for stainless steel body Optional plug material VM Alloy 6 Stellite 6 Alloy steel Y Special materials 9. PLUG APPLICATION X Not applicable A Cobalt based alloy 10. STEM MATERIAL Material Description BC 630 SS + HCr Standard for carbon steel body TC 316 SS + HCr Standard for stainless steel body Y Special materials 11. SEAT TYPE Optional seat type T1 Single soft seat Y 12. SEAT / RETAINER MATERIAL Seat Retainer Guide bushing R1 CA15 / 410 SS CB7Cu-1 / 630 SS AISI 440C T6 CF8M / 316 SS CF8M / 316 SS AISI 316 + Alloy 6 Y Special Special * CA15 / 410 SS is the standard material for carbon steel body. ** CF8M / 316 SS is the standard material for stainless steel body. 13. SEAT APPLICATION X Not applicable A Cobalt based alloy Optional seat application P Insert PTFE R Insert RTFE OTHERS 14. PACKING TYPE S Standard packing Optional packing type L Live loaded packing B Bellows Seal (316L SS, Welded) C Bellows Seal (304 SS, Formed) 15. PACKING MATERIAL G PTFE + Carbon fiber Optional packing material F Graphite (with mold and braided) 16. SEALS MATERIAL X Not applicable 17. GASKET MATERIAL S S/W gasket type, 316 SS + Graphite for standard Optional gasket material H S/W gasket type, 316 SS + Graphite for high temp. L S/W gasket type, 316 SS + PTFE 18. STUD / NUT MATERIAL A A193 gr. B7 / A194 gr. 2H B A193 gr. B8 / A194 gr. 8 Optional bolting material H A193 gr. B16 / A194 gr. 4 19. OPTIONS X Not applicable E Anti-erosion L Lub. & Isol. valve W Water seal * The body, bonnet, trim materials are subject to change as equivalent depending on detail design. 11. SEAT TYPE S1 Single metal seat

20 4 GV 73 en TRIM TYPE & RATED Cv - Series AU 20. 21. 22. RATED Cv TRIM TRIM TYPE Sign Sign CHARACTERISTIC Sign Description Body size and Stroke 1" Srk. 1-1/2" Srk. 2" Srk. 3" Srk. 4" Srk. A Standard plug type L Linear FC Full capacity 14 (20) 28 (20) 52 (20) 124 (40) 220 (40) E Equal % 1A 1-Step reduction 8 (20) 16 (20) 30 (20) 74 (40) 128 (40) Q Quick opening 2A 2-Step reduction 5 (20) 10 (20) 18 (20) 46 (40) 78 (40) 3A 3-Step reduction 3 (20) 6 (20) 12 (20) 28 (40) 46 (40) L Linear FT Tendril 1 stage / Full capacity 12 (20) 24 (20) 44 (20) 100 (40) 196 (40) Q Quick opening 1T Tendril 1 stage / 1-Step reduction 8 (20) 14 (20) 28 (20) 62 (40) 114 (40) 2T Tendril 1 stage / 2-Step reduction 5 (20) 8 (20) 16 (20) 38 (40) 68 (40) 3T Tendril 1 stage / 3-Step reduction 3 (20) 5 (20) 10 (20) 24 (40) 40 (40) FM Tendril 2 stage / Full capacity 8 (20) 16 (20) 32 (20) 74 (40) 130 (40) 1M Tendril 2 stage / 1-Step reduction 5 (20) 10 (20) 20 (20) 46 (40) 80 (40) 2M Tendril 2 stage / 2-Step reduction 3 (20) 6 (20) 14 (20) 28 (40) 48 (40) 3M Tendril 2 stage / 3-Step reduction 2 (20) 4 (20) 8 (20) 16 (40) 30 (40) E Equal % FT Tendril 1 stage / Full capacity 12 (20) 24 (20) 44 (20) 100 (40) 196 (40) 1T Tendril 1 stage / 1-Step reduction 8 (20) 14 (20) 28 (20) 62 (40) 110 (40) 2T Tendril 1 stage / 2-Step reduction 5 (20) 8 (20) 16 (20) 38 (40) 68 (40) 3T Tendril 1 stage / 3-Step reduction 3 (20) 5 (20) 10 (20) 24 (40) 40 (40) FM Tendril 2 stage / Full capacity 8 (20) 16 (20) 32 (20) 74 (40) 130 (40) 1M Tendril 2 stage / 1-Step reduction 5 (20) 10 (20) 20 (20) 46 (40) 80 (40) 2M Tendril 2 stage / 2-Step reduction 3 (20) 6 (20) 14 (20) 28 (40) 48 (40) 3M Tendril 2 stage / 3-Step reduction 2 (20) 4 (20) 8 (20) 16 (40) 30 (40) G Multi groove plug type L Linear FC Full capacity 4 (20) 9 (20) 18 (20) - (40) - (40) 1A 1-Step reduction 3 (20) 6 (20) 10 (20) - (40) - (40) 2A 2-Step reduction 2 (20) 4 (20) 6 (20) - (40) - (40) 3A 3-Step reduction 1 (20) 2 (20) 4 (20) - (40) - (40) C Micro plug type L Linear - - Contact Metso for Cv details Y Contact Metso for Cv details NOTE 1. Rated Cvs are applied differently depending on the trim type & trim characteristics. 2. The larger Cvs and sizes are available, please contact Metso. 3. Micro (Mini flow) trims are available. 4. (Srk) means the valve stroke in mm. 5. The other Cvs and trim types, please contact Metso.

4 GV 73 en 21 Angle Balanced, Cage Guided Type, Series AB 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. AB 03 C W A J2 X P1 X BC S1 R1 X S G G S A X A L FC VALVE CONSTRUCTIONS 1. VALVE SERIES AB Angle Balanced, Cage guided type 2. BODY SIZE 02 2" / DN 50 03 3" / DN 80 04 4" / DN 100 06 6" / DN 150 08 8" / DN 200 10 10" / DN 250 12 12" / DN 300 14 14" / DN 350 16 16" / DN 400 Optional Body Size 18 18" / DN 450 20 20" / DN 500 24 20" / DN600 Y 3. PRESSURE RATING C ASME Class 150 D ASME Class 300 F ASME Class 600 Optional pressure rating G ASME Class 900 H ASME Class 1500 I ASME Class 2500 4. END CONNECTION W Flanged RF, ASME B16.5 Optional end connection V Socket welding, ASME B16.11 Q Butt welding, ASME B16.25 Z Ring joint flange, ASME B16.5 5. BONNET CONSTRUCTION Bonnet type Actuator connection A Standard Standard actuator size B Standard Applicable for VD_48/55 (3",4" only) Optional bonnet construction E Extension Standard actuator size F Extension Applicable for VD_48/55 (3",4" only) L Bellows seals Standard actuator size M Bellows seals Applicable for VD_48/55 (3",4" only) Special 6. BODY & BONNET MATERIAL J2 A216 gr. WCB S6 A351 gr. CF8M Optional body & Bonnet material S4 A351 gr. CF8 S9 A351 gr. CF3 S1 A351 gr. CF3M Y 7. BEARINGS (TRUNNION / THRUST BEARING) X Not applicable TRIM CONSTRUCTIONS 8. PLUG MATERIAL Material Description P1 A743 gr. CA15 Standard for carbon steel body T6 A351 gr. CF8M Standard for stainless steel body Y Special materials 9. PLUG APPLICATION X Not applicable C Hard chrome A Cobalt based alloy D Cobalt based alloy + HCr * CF8M (AB plug) must to be coated hard chrome basically. 10. STEM MATERIAL Material Description BC 630 SS + HCr Standard for carbon steel body TC 316 SS + HCr Standard for stainless steel body Y Special materials 11. SEAT TYPE S1 Single metal seat Optional seat type T1 Single soft seat Y 12. SEAT / CAGE MATERIAL Seat Cage Cage Guide R1 CA15 * CB7Cu-1 / 630 SS + HCr CB7Cu-1 + HCr R6 CF8M ** CF8M / 316 SS + HCr CF8M + HCr Y Special Special * CA15 is the standard material for carbon steel body. ** CF8M is the standard material for stainless steel body. 13. SEAT APPLICATION X Not applicable A Cobalt based alloy Optional seat application P Insert PTFE R Insert RTFE OTHERS 14. PACKING TYPE S Standard packing Optional packing type L Live loaded packing B Bellows Seal (316L SS, Welded) C Bellows Seal (304 SS, Formed) 15. PACKING MATERIAL G PTFE + Carbon fiber Optional packing material F Graphite (with mold and braided) 16. SEALS MATERIAL G PTFE + Graphite Optional seals material T PTFE F Graphite C Metal C-seal ring M Metal (Ductile) 17. GASKET MATERIAL S S/W gasket type, 316 SS + Graphite for standard Optional gasket material H S/W gasket type, 316 SS + Graphite for high temp. L S/W gasket type, 316 SS + PTFE 18. STUD / NUT MATERIAL A A193 gr. B7 / A194 gr. 2H B A193 gr. B8 / A194 gr. 8 Optional bolting material H A193 gr. B16 / A194 gr. 4 19. OPTIONS X Not applicable E Anti-erosion L Lub. & Isol. valve W Water seal

22 4 GV 73 en TRIM TYPE & RATED Cv - Series AB 20. 21. 22. RATED Cv TRIM TRIM TYPE Sign Sign CHARACTERISTIC Sign Description Body size and Stroke 2" Srk. 3" Srk. 4" Srk. 6" Srk. 8" Srk. 10" Srk. 12" Srk. 14" Srk. 16" Srk. A Standard plug type L Linear FC Full capacity 82 (40) 174 (50) 280 (50) 470 (60) 810 (70) 1250 (80) 1810 (100) 2530 (120) 2960 (140) P Pilot balanced plug type Q Quick opening 1A 1-Step reduction 74 (40) 104 (50) 170 (50) 284 (60) 500 (70) 760 (80) 1100 (100) 1540 (120) 1780 (140) 2A 2-Step reduction 44 (40) 62 (50) 100 (50) 170 (60) 320 (70) 460 (80) 680 (100) 940 (120) 1080 (140) 3A 3-Step reduction 26 (40) 40 (50) 64 (50) 100 (60) 200 (70) 280 (80) 420 (100) 580 (120) 660 (140) FT Tendril 1 stage / Full capacity 72 (40) 156 (50) 250 (50) 420 (60) 720 (70) 1120 (80) 1620 (100) 2270 (120) 2660 (140) 1T Tendril 1 stage / 1-Step reduction 44 (40) 94 (50) 156 (50) 256 (60) 430 (70) 680 (80) 980 (100) 1380 (120) 1600 (140) 2T Tendril 1 stage / 2-Step reduction 26 (40) 56 (50) 94 (50) 156 (60) 260 (70) 420 (80) 590 (100) 830 (120) 980 (140) 3T Tendril 1 stage / 3-Step reduction 18 (40) 34 (50) 60 (50) 94 (60) 156 (70) 252 (80) 360 (100) 500 (120) 600 (140) FM Tendril 2 stage / Full capacity 52 (40) 110 (50) 174 (50) 300 (60) 510 (70) 800 (80) 1150 (100) 1610 (120) 1890 (140) 1M Tendril 2 stage / 1-Step reduction 30 (40) 68 (50) 110 (50) 180 (60) 310 (70) 500 (80) 700 (100) 980 (120) 1140 (140) 2M Tendril 2 stage / 2-Step reduction 18 (40) 40 (50) 70 (50) 110 (60) 186 (70) 310 (80) 420 (100) 600 (120) 680 (140) 3M Tendril 2 stage / 3-Step reduction 12 (40) 26 (50) 48 (50) 72 (60) 114 (70) 120 (80) 252 (100) 360 (120) 420 (140) E Equal % FC Full capacity 76 (40) 160 (50) 256 (50) 430 (60) 740 (70) 1140 (80) 1650 (100) 2300 (120) 2700 (140) 1A 1-Step reduction 46 (40) 98 (50) 156 (50) 260 (60) 450 (70) 680 (80) 1000 (100) 1400 (120) 1640 (140) 2A 2-Step reduction 28 (40) 60 (50) 94 (50) 156 (60) 270 (70) 410 (80) 640 (100) 840 (120) 980 (140) 3A 3-Step reduction 18 (40) 36 (50) 60 (50) 96 (60) 164 (70) 250 (80) 384 (100) 520 (120) 600 (140) FT Tendril 1 stage / Full capacity 68 (40) 140 (50) 230 (50) 384 (60) 660 (70) 1020 (80) 1480 (100) 2050 (120) 2420 (140) 1T Tendril 1 stage / 1-Step reduction 42 (40) 84 (50) 140 (50) 230 (60) 400 (70) 620 (80) 890 (100) 1240 (120) 1460 (140) 2T Tendril 1 stage / 2-Step reduction 24 (40) 50 (50) 86 (50) 142 (60) 250 (70) 380 (80) 540 (100) 760 (120) 880 (140) 3T Tendril 1 stage / 3-Step reduction 16 (40) 30 (50) 54 (50) 88 (60) 160 (70) 240 (80) 340 (100) 460 (120) 540 (140) FM Tendril 2 stage / Full capacity 48 (40) 100 (50) 160 (50) 274 (60) 470 (70) 726 (80) 1050 (100) 1470 (120) 1720 (140) 1M Tendril 2 stage / 1-Step reduction 28 (40) 60 (50) 94 (50) 164 (60) 284 (70) 440 (80) 640 (100) 890 (120) 1040 (140) 2M Tendril 2 stage / 2-Step reduction 16 (40) 36 (50) 54 (50) 100 (60) 170 (70) 264 (80) 384 (100) 540 (120) 640 (140) 3M Tendril 2 stage / 3-Step reduction 10 (40) 24 (50) 32 (50) 64 (60) 100 (70) 160 (80) 240 (100) 340 (120) 384 (140) Y Contact Metso for Cv details NOTE 1. Rated Cvs are applied differently depending on the trim type & trim characteristics. 2. The larger Cvs and sizes are available, please contact Metso. 3. Micro (Mini flow) trims are available. 4. (Srk) means the valve stroke in mm. 5. The other Cvs and trim types, please contact Metso.

4 GV 73 en 23 Angle Omega Trim, Multi-Stage Type, Series AM 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. AM 02 H Z A J2 X P2 X BC S1 P2 X S G G S A X A L FG VALVE CONSTRUCTIONS 1. VALVE SERIES AM Angle Omega trim, Multi stage 10. STEM MATERIAL BC 630 SS + HCr Y 2. BODY SIZE 01 1" / DN 25 1H 1-1/2" / DN 40 02 2" / DN 50 03 3" / DN 80 04 4" / DN 100 06 6" / DN 150 08 8" / DN 200 10 10" / DN 250 12 12" / DN 300 14 14" / DN 350 16 16" / DN 400 18 18" / DN 450 20 20" / DN 500 Y 3. PRESSURE RATING C ASME Class 150 D ASME Class 300 Optional pressure rating F ASME Class 600 G ASME Class 900 H ASME Class 1500 I ASME Class 2500 A ASME Class 4500 4. END CONNECTION W Flanged RF, ASME B16.5 Optional end connection V Socket welding, ASME B16.11 Q Butt welding, ASME B16.25 Z Ring joint flange, ASME B16.5 BONNET CONSTRUCTION 5. Bonnet type Actuator connection A Standard Standard actuator size B Standard Applicable for VD_48/55 (3",4" only) Optional bonnet construction E Extension Standard actuator size F Extension Applicable for VD_48/55 (3",4" only) Special 6. BODY & BONNET MATERIAL J2 A216 gr. WCB S6 A351 gr. CF8M Optional body & Bonnet material S4 A351 gr. CF8 S9 A351 gr. CF3 S1 A351 gr. CF3M Y 7. BEARINGS (TRUNNION / THRUST BEARING) X Not applicable TRIM CONSTRUCTIONS 8. PLUG MATERIAL P2 SUS 420J2 Y 9. PLUG APPLICATION X Not applicable A Cobalt based alloy Optional plug application C Hard chrome D Cobalt based alloy + HCr * CF8M (AB plug) must to be coated hard chrome basically. 11. SEAT TYPE S1 Single metal seat Y SEAT / DISK STACK MATERIAL 12. Seat Disk Stack Cage Guide P2 SUS 420J2 SUS 420J2 SUS 420J2 Y Special Special * CA15 is the standard material for carbon steel body. ** CF8M is the standard material for stainless steel body. 13. SEAT APPLICATION X Not applicable A Cobalt based alloy Optional seat application OTHERS 14. PACKING TYPE S Standard packing Optional packing type L Live loaded packing 15. PACKING MATERIAL G PTFE + Carbon fiber Optional packing material F Graphite (with mold and braided) 16. SEALS MATERIAL X Not applicable G PTFE + Graphite Optional seals material T PTFE F Graphite C Metal C-seal ring M Metal (Ductile) 17. GASKET MATERIAL S S/W gasket type, 316 SS + Graphite for standard Optional gasket material H S/W gasket type, 316 SS + Graphite for high temp. L S/W gasket type, 316 SS + PTFE 18. STUD / NUT MATERIAL A A193 gr. B7 / A194 gr. 2H B A193 gr. B8 / A194 gr. 8 Optional bolting material H A193 gr. B16 / A194 gr. 4 19. OPTIONS X Not applicable E Anti-erosion L Lub. & Isol. valve W Water seal

24 4 GV 73 en TRIM TYPE & RATED Cv - Series AM 20. 21. 22. RATED Cv TRIM TRIM Sign TYPE Sign CHARACTERISTIC Sign Description Body size and Stroke 1" Srk.1-1/2"Srk. 2" Srk. 3" Srk. 4" Srk. 6" Srk. 8" Srk. 10" Srk.12" Srk. 14" Srk. 16" Srk. A Balanced plug type L Linear FG Full capa. / Gas 7 (30) 16 (30) 26 (40) 54 (50) 84 (50) 146 (60) 252 (70) 384 (80) 560(100)770(120)1020(140) P Pilot balanced plug type Q Quick opening FL Full capa. / Liquid U Unbalanced plug type 1G 1-Step red. / Gas 3 (30) 8 (30) 12 (40) 28 (50) 52 (50) 90 (60) 156 (70) 234 (80) 340(100)470(120) 624 (140) 1L 1-Step red. / Liquid 2G 2-Step red. / Gas 1.6 (30) 4 (30) 6 (40) 14 (50) 26 (50) 45 (60) 78 (70) 116 (80) 170(100)234(120) 310 (140) 2L 2-Step red. / Liquid 3G 3-Step red. / Gas 0.8 (30) 2 (30) 3 (40) 7 (50) 14 (50) 22 (60) 40 (70) 58 (80) 84 (100)116(120) 154 (140) 3L 3-Step red. / Liquid E Equal % FG Full capa. / Gas 5 (30) 10 (30) 18 (40) 38 (50) 60 (50) 104 (60) 176 (70) 268 (80) 390(100)540(120) 710 (140) FL Full capa. / Liquid 1G 1-Step red. / Gas 2.5 (30) 6 (30) 11 (40) 24 (50) 36 (50) 64 (60) 108 (70) 164 (80) 236(100)328(120) 430 (140) 1L 1-Step red. / Liquid 2G 2-Step red. / Gas 1.2 (30) 3 (30) 5 (40) 12 (50) 18 (50) 32 (60) 54 (70) 82 (80) 118(100)164(120) 214 (140) 2L 2-Step red. / Liquid 3G 3-Step red. / Gas 0.6 (30) 1.5 (30) 2 (40) 6 (50) 9 (50) 16 (60) 27 (70) 40 (80) 60 (100) 82 (120) 106 (140) 3L 3-Step red. / Liquid Y Contact Metso for Cv details NOTE 1. Rated Cvs are applied differently depending on the trim type & trim characteristics. 2. The larger Cvs and sizes are available, please contact Metso. 3. Micro (Mini flow) trims are available. 4. (Srk) means the valve stroke in mm. 5. The other Cvs and trim types, please contact Metso. Metso Flow Control Inc. South Korea, 235 Cheomdansaneop 1-ro, Daesowon-myeon, Chungju-si, Chungbuk-do, 27466, Korea Tel. +82 43 852 7708, Fax +82 43 841 9890 Europe, Vanha Porvoontie 229, P.O. Box 304, FI-01301 Vantaa, Finland. Tel. +358 20 483 150. Fax +358 20 483 151 North America, 44 Bowditch Drive, P.O. Box 8044, Shrewsbury, M A 01545, USA. Tel. +1 508 852 0200. Fax +1 508 852 8172 South America, Av. Independéncia, 2500-Iporanga, 18087-101, Sorocaba-São Paulo, Brazil. Tel. +55 15 2102 9700. Fax +55 15 2102 9748 Asia Pacific, 238B Thomson Road, #17-01 Novena Square Tower B, Singapore 307685. Tel. +65 6511 1011. Fax +65 6250 0830 China, 11/F, China Youth Plaza, No.19 North Rd of East 3rd Ring Rd, Chaoyang District, Beijing 100020, China. Tel. +86 10 6566 6600. Fax +86 10 6566 2583 Middle East, Roundabout 8, Unit AB-07, P.O. Box 17175, Jebel Ali Freezone, Dubai, United Arab Emirates. Tel. +971 4 883 6974. Fax +971 4 883 6836 www.metso.com/valves