2014 CATALOG AUTOMATIC DOOR ACTIVATION SOLUTIONS Standard & Customized Bollards Standard Switches, Key Switches & Mounts the INGRESS R Wireless and Touchless Customized Switches Specified in: MasterFormat Section 08710 (08 71 20) Automatic Door Controls
All AccessAbility switches are ready for wireless or hard-wired applications to flush mounted single-gang or double-gang electrical junction boxes. A variety of surface and flush mounts give you the flexibility you need to meet the specific requirements of your installation (design, energizing, visibility, safety) described on corresponding switch pages. The red asterisk ( ) = a Radio Frequency-compatible mount. Switch and Mounting Compatibility Chart NOTE: Exterior application - for moisture evaporation drill 1/32 weephole in the bottom of box. PRODUCT IDENTIFICATION CODE SWITCHES BOLLARDS 4R = 4 1 /2 Round AA = All-Active BPS = Bollard Post Square 4x4 = 4 1 /2 by 4 1 /2 Square NS = Narrow Style BPR = Bollard Post Round 6R = 6 Round KS-N = Key Switch Narrow BPRT = Bollard Post Rectangular 6x6 = 6 by 6 Square KS-P = Key Switch Prep BPTR = Bollard Post Triangle SFA = Single gang Full-Active KS-4 = Key Switch 4x4 SM = Surface Mount SPB = Single gang Push Button I36 = INGRESS R 36 Length IG = In Ground = SWITCHES MOUNTING OPTIONS 4R WKS-4 7 1 /4 Dia. X 1 1 /4 O.D. (184 X 30 mm) 1 Inside Depth (25 mm) SURF 4R 2 3 /4 X 4 1 /2 X 1 11 /16 D (70 X 114 X 43 mm) 1 9 /16 Inside Depth (40 mm) WKS-4RF 7 13 /16 Dia. X 1 9 /16 overall ht. (200 mm X 40 mm) 1 25 /64 Inside Depth (35.5 mm) 6 Square BOLLARD N4RS N4RF 5 Dia. X 2 1 /8 H 5 7 /8 Dia. X 2 1 /8 H (127 X 54 mm) (149 X 54 mm) with trim ring 115 /16 Inside Depth (49 mm) 1 15 /16 Inside Depth (49 mm) 6 Round BOLLARD + CUFF NOTE: N4RF is flush mounted 4x4 KS-4 6R SURF SQ 4 & 6 BLK 4 19 /32 W X 4 19 /32 H X 1 3 /4 D (117 X 117 X 44 mm) 1 5 /8 Inside Depth (41 mm) N4X4S 5 1 /2 W X 5 1 /2 H X 2 1 /8 D (140 X 140 X 54 mm) 5 X 5 Inside (127 X 127 mm) 1 15 /16 Inside Depth (49 mm) WKS-6 9 1 /2 Dia. X 1 Overall Height (241 X 25 mm) 7/8 Inside Depth (22 mm) N6RS 6 7 /16 Dia. X 2 1 /8 H (164 X 54 mm) 1 15 /16 Inside Depth (49 mm) SURF 4/M 4 X 4 X 1 1 /8 O.D. (102 X 102 X 29 mm) 1 1 /8 Inside Depth (29 mm) N4X4F 6 3 /4 X 6 3 /4 X 2 1 /8 (172 X 172 X 54 mm) 1 7 /8 Inside Depth (47.6 mm) SURF 6R 4 19 /32 W X 4 19 /32 H X 1 3 /4 D (117 X 117 X 44 mm) 1 1 /2 Inside Depth (38 mm) N6RF 7 3 /4 Dia. X 2 1 /8 H (197 X 54 mm) with trim ring 1 7 /8 Inside Depth (48 mm) 6 Square BOLLARD NOTE: N4X4F is flush mounted 6 Square BOLLARD NOTE: N6RF is flush mounted 6 Round BOLLARD SURF 6/M 4 W X 4 H X 3 /4 D (102 X 102 X 19 mm) 3/4 Inside Depth. (19 mm) + CUFF 6x6 SFA KS-P SPB NS AA KS-N SURF SQ 4 & 6 BLK 4 19 /32 W X 4 19 /32 H X 1 3 /4 D (117 X 117 X 44 mm) 1 5 /8 Inside Depth (41 mm) SURF SFA 2 3 /4 X 4 1 /2 X 1 5 /8 O.D. (70 X 114 X 41 mm) 1 1 /2 Inside Depth (38 mm) JSB 1 3 /4 X 4 9 /16 X 1 3 /4 O.D. (44 X 116 X 44 mm) 1 5 /8 Inside Depth (41 mm) SURF 6/M 4 X 4 X 3 /4 O.D. (102 X 102 X 19 mm) 3/4 Inside Depth (19 mm) SURF 4R 2 3 /4 X 4 1 /2 X 1 11 /16 D (70 X 114 X 43 mm) 1 9 /16 Inside Depth (40 mm) 4 or 6 Square BOLLARD Requires AA prep 6 Square BOLLARD 4 or 6 Square BOLLARD 6 Round BOLLARD + CUFF INGRESS R 6 Square BOLLARD Requires INGRESS R prep 8 Round BOLLARD + INGRESS R CUFF
Benefits and Value of working with Wikk: For more than 30 years Wikk AccessAbility switches and bollards have been manufactured in the USA at our Wisconsin factory. We use quality materials and craftsmanship to ensure dependability in high traffic areas and harsh weather conditions. AccessAbility products meet or exceed accessibility requirements around the world such as the ADA, AODA, The Equality Act of 2010, Australia s Premises Standards of 2011, and more. The AccessAbility line is applicable, and not limited to CSI Divisions 5, 8, 14 and 28. AccessAbility switches can be customized with special engraving (logos, images, and text), Grade 2 Braille, infill colors and material finishes. Project-specific requirements for access control, communication and accessibility can be attractively coordinated within a custom Wikk bollard, and manufactured from a wide variety of materials and finishes to complement architectural design. The contents of Wikk products exceed the minimum recommended percentages of recycled materials and the company supports green initiatives by utilizing North American products and suppliers as much as possible. Wikk provides an 18 month warranty on switches and bollards from the date of shipment MADE IN and 24 months on wireless products from the date of manufacture. Every day we exceed our customers expectations with friendly customer service and reasonable lead times. We look forward to working with you on your next project. U.S.A. GENERAL INFORMATION Switch Cover Materials and Finishes These finish colors are printer s reproductions and may vary from actual colors. Call for samples. Standard (STD) SATIN STAINLESS STEEL US32D (630) Type 304-18 Gauge MIRROR STAINLESS STEEL US32 (629) Type 304-18 Gauge SATIN BRASS US4 (606) Uncoated Type Naval Brass - 18 Gauge MIRROR BRASS US3 (605) Uncoated Type Naval Brass - 18 Gauge OIL-RUBBED and RELIEVED OXIDIZED BRASS US10B (613) Type Naval Brass - 18 Gauge Standard (STD) Switches are debossed and infilled with color (stocked) Non-standard Switches are engraved and infilled or debossed, depending on the design and quantity ordered. (Lead time approximately 2-3 weeks) SWITCH OPTIONS Decorative materials and finishes Custom Engraving legends, logos, image and texts Custom Infill coloration- Chocolate Brown, Green, Red and White; also available in our standard Blue and Black infill Grade 2 Braille lettering Weather (WR) and infiltration-resistant Double Pole Double Throw (DPDT) micro-switch for dual operations (example: for lock release) Quick-connect wireless products for Radio Frequency operation (See page 18-19) Pneumatic operation, used in fail-safe exit, hazardous area that requires no electrical charge Anti-Microbial Coating For Bollard Options see page 2 1
Standard & Custom BOLLARD POSTS Standard Lead-times: Standard bollards: Same day shipping if ordered by noon CST. Custom bollards: Lead-time is 1-5 weeks depending on the design. Shape: BPS = Square BPR = Round BPRT = Rectangular BPTR = Triangle Mounting Installation options: SM = Surface mount: standard posts are 42 [1067 mm] high, single gang prep @ 36 CL/AFF [914 mm]; includes aluminum anchoring base, anchors and instructions. IG = In-ground: standard posts are 54 [1372 mm] high, single gang prep @ 36 CL/AFF [914 mm] including 12 [305 mm] recess and instructions. Overall height: Can be customized to be shorter or taller than standard height. Architectural Materials & Finishes: Square (BPS) Aluminum Tubes: Anodized Aluminum: Clear (628), Dark Bronze (710), Black (711), and Mill finish for painting (PT) or powder coating (PC); Light Bronze Anodized (available for 6 square bollards only) Wall Thickness and Corner Radius for Aluminum: Extruded; nominal 1/8 [3.175 mm] wall thickness, 4 and 6 Square: 1/32 corner radius Square (BPS) Stainless Steel Tubes: Satin Stainless Steel US32D (630) or Mirror Stainless Steel US32 (629) finishes Wall Thickness and Corner Radius for Square Stainless Steel: Welded type 304; nominal 1/8 [3.175 mm] wall thickness 4 and 6 Square: 15/64 corner radius 316 alloy available as special order Brass Clad Aluminum (Square only): Nominal 18/19 gauge sheet metal over standard Aluminum extrusion, 9/64 corner radius Satin Brass US4 (606 uncoated) or Mirror Brass US3 (605 uncoated) finishes. Protective coating by others. Round (BPR) Aluminum Tubes: Anodized Aluminum: Dark Bronze (710) and Mill finish for painting (PT) or powder coating (PC) Powder coated (PC): To match Clear Anodized Aluminum Wall Thickness: Extruded; nominal 5/32 [4 mm] wall thickness Round (BPR) Stainless Steel Tubes: Satin Stainless Steel US32D (630) or Mirror Stainless Steel US32 (629) finishes Wall Thickness for Square Stainless Steel: Welded type 304; nominal 1/8 [3 mm] wall thickness 316 alloy available as special order Wikk Bollard Options: Preps: INGRESS R, standard and narrow style switches, card readers, intercoms, KNOX-boxes, fire pull stations and more. Square (BPS), Rectangular (BPRT) and Triangle (BPTR) Bollards: Switches and devices mount directly to post. Round (BPR) bollard: Curved switch (6C series) mounts directly to post. Use Adapter Cuff for additional items or flat switch styles. Round bollards can be modified with recessed insert area to accommodate flat devices. At the time of quoting/ordering bollards we require the make, model, as well as mounting templates of all the devices to assure accurate preps. Production will not start until the device information is provided. All information is kept confidential. Cap style & finish: Flat top (FT): Standard black removable top (allows RF transmission) Flat top (FT): Stainless Steel, Aluminum and Brass removable top (not available for round bollards) Flat top (FT): Welded Flat Top for Stainless or Mill Aluminum for painting (PT) or powder coating (PC) finishes Angled top (AT): Welded Stainless Steel, or Mill Aluminum for painting (PT) or powder coating (PC) finishes; also available in Removable Angle Top (RAT) Dome (D): Round only, Welded Stainless, or Mill Aluminum for painting (PT) or powder coating (PC) finishes Additional Options: Special sizes available per request - See Wikk s Bollard Checklists on website. Example: 3 x 3, 7 x 7, 9 x 9, 6 x 9, 6 x 12 and Triangle Bollards available in Stainless Steel, Aluminum and Steel. Sizes are subject to change without notice. Painted (PT) or Powder coated (PC) finish available Exposed Base Plate - different sizes available in round (RB), square (SB), rectangle (RTB) and concealed sleeve (CS) with base plate for In-ground mounting with additional anchoring, 7 bolts and anchors Access Panel (AP) - Removable access panel on the back of bollard or the insert area with security screws. Hood - Added over devices to help protect from environmental conditions. Decorate Reveal (R) - Decorative reveal in the metal. For additional custom design solutions: Contact Wikk Industries, Inc. 2 COLOR KEY These finish colors are printer s reproductions and may vary from actual colors. Call for samples. CLEAR (628) SATIN STAINLESS STEEL (630) DARK BRONZE (710) MIRROR STAINLESS STEEL (629) LIGHT BRONZE (Square Only) SATIN BRASS CLAD (606-uncoated) (Square Only) BLACK (711) (Square Only) MIRROR BRASS CLAD (605-uncoated) (Square Only)
BOLLARDS B4S SM-PREP36 CLEAR 4 x 4 x 42 Tall, Clear Anodized Aluminum (628), concealed mounting base, 1 Prep at 36 AFF for ADA switch, Removable Black ABS cap BPS SM-PRP36 LB 6 x 6 x 42 Tall, Light Bronze Anodized Aluminum concealed mounting base, 1 Prep at 36 AFF for ADA switch, Removable Black ABS cap BPS SM TUBE 32D 6 x 6 x 42 Tall, 304 Satin Stainless Steel in US32D (630), concealed mounting base, 1 prep at 36 AFF for ADA switch, Removable Black ABS cap BPS SM-INGR DK BZ with I36-5 Dark Bronze 6 x 6 x 42 Tall, Dark Bronze Anodized Aluminum (710), concealed mounting base, 1 prep for INGRESS R ADA switch, Removable Black ABS cap BPS SM-ING48 DB with I36-3 Clear 6 x 6 x 48 Tall, Dark Bronze Anodized Aluminum (710), concealed mounting base, 2 Preps for INGRESS R and card reader, Removable Black ABS Cap BPS IG-HI/LO CLEAR 6 x 6 x 54 Tall, Clear Anodized Aluminum (628), In-ground mount, 2 preps for ADA switches, Removable Black ABS cap BPR SM-PC CLEAR 6 RD x 42 Tall, Powder coated (PC) to match Clear Aluminum, concealed mounting base, 1 prep at 36 AFF for Wikk 6C-5 WR US32D ADA curved switch, Removable Black ABS cap BPR SM US32 6 RD x 42 Tall, 304 Mirror Stainless Steel US32 (629), concealed mounting base, 1 prep at 36 AFF for Wikk 6C-3 WR US32 ADA curved switch, Removable Black ABS cap BPDSMPREP36 PTDB 6 RD x 45 Tall, Mill Aluminum, painted (PT) to match Dark Bronze Aluminum, concealed mounting base, 1 prep at 36 AFF for Wikk 6C-3 WR US32D ADA curved switch, Welded Dome Top (D) BPR SM-AINS 32D 6 Rd x 48.625 Tall, 304 Satin Stainless Steel US32D (630), concealed mounting base, Recess area for flat devices, Welded Angle top (front slant) (AT) 3
Standard & Custom BOLLARD POSTS GET THE EDGE SQUARE ONLY 4x4 Edge US32D 4 11 /16 tall X 4 7 /8 wide X 1 /2 deep (118 x 124 x 8 mm) Sturdy 3-sided stainless shroud protects the switch components from harsh environmental conditions and wash down chemicals. Especially effective against freezing rain and snow infiltration to prevent temporary ice buildup. Offers a decorative appeal by concealing the gap between the faceplate and backplate of the switch. Insert between the bollard and backplate of the switch. SHOWN Recommended for exterior bollards. WITH SWITCH (Sold separately) Hard-Wire and Wireless (with standard bollard cap) ROUND ONLY 6 x 6 Curved Switch Part# 6C-3 WR (shown) Wikk AccessAbility Exclusive! Part# 6C-5 WR (ADA logo only) also available A dramatic look with high visibility 6 x 6 (152 x152 mm) Standard finish is US32D (630) 316 Alloy Heavy-duty 1/8 (3 mm) thick material Weather-resistant (WR) Radius conforms to bollard design OPTIONS: Finishes: US32 (629), US4 (606 uncoated), US3 (605 uncoated), US10B (613) Custom engraving Hard-wire and Wireless SQUARE & ROUND Standard Bollard Caps Square shown; same features in round. See page 18 and 19 for wireless products. Hard-Wire and Wireless ROUND ONLY 1-Gang Adapter Cuff Part# BP4X4ADTRFBLK Sturdy, textured black ABS material Multi-purpose use A mounting bridge between a flat device and round bollard (card/proximity reader, switch, etc.) Allows RF transmission when metal bollard cap is utilized Alternative to 6C series switch Cuff mounts onto bollard 1-gang prep. Device mounts directly to 1-gang face prep of the cuff. 1-5/8 (41 mm) profile, not including device 4-1/2 x 4-1/2 (114 x 114 mm) O.D. Also available in Stainless Steel (does not allow RF transmission) Stainless Steel and Aluminum posts can be fabricated with a recess for flat devices Access Panel Removable Access Panel (AP) on the back of bollards or the insert area with security screws Additional Options Base Plates Exposed Surface Mount with mounting holes Available: Round Base (RB), Square Base (SB) or Rectangluar Base (RTB) not shown. Reveals (R) Decorative Reveal in the material Concealed Sleeve for In-ground mounting Available: Round Base (RB), Square Base (SB) or Rectangular Base (RTB) Removable Angle Top (RAT) to allow access with a decorative touch 4
BOLLARDS B3FSMRBPRP3632D 3 x 3 x 42 Tall, 304 Satin Stainless Steel US32D (630), welded round base plate (RB), 1 Prep for ADA switch, Welded Flat Top (FT) BPRT126SMFT32D 12 x 6 x 42 Tall, 7ga. Formed 304 Satin Stainless Steel US32D (630) concealed mounting base, 1 prep for INGRESS R ADA switch, Welded Flat Top (FT) Best Bollards in the business say our customers and our competitors BPR8 SM AINS32D 8 Rd x 45 Tall, 304 Satin Stainless Steel US32D (630), concealed mounting base, Flat Recessed area for ADA switch and Card Reader, Welded Angle Top to the back (AT) BPRT96SMSBAT32D 9 x 6 x 48 Tall, 7ga. Formed 304 Satin Stainless Steel US32D (630), welded square mounting base plate (SB),1 prep for Keypad/Card Reader, Welded Angle Top (AT) BPSSMAHOODH/L32D 6 x 6 x 42 Tall, 304 Satin Steel in US32D (630), concealed mounting base, 2 preps with Stainless Steel hood over the upper ADA Switch, Welded Angle top (AT) (front slant) BPTR6SMRBP3632D 6 x 6 x 6 x 42 Tall, TRIANGLE 7ga. Formed 304 Satin Stainless Steel US32D (630), welded round base plate (RB), 1 Prep for ADA switch, Welded Flat Top (FT) BPSSM36RATPCDK 6 x 6 x 54 Tall, Mill Aluminum Powder coated (PC) to match Dark Bronze Aluminum, concealed mounting base, 1 prep for ADA switch, Removable Angle top (RAT) (front slant) BPS IG CS 32D 6 x 6 x 48 Tall, 304 Satin Steel in US32D (630), Removable bollard for In-ground mounting with concealed sleeve (CS) and base plate, 2 preps for ADA switch and Card reader, Removable Black ABS cap BPD8SMRBINS32D 8 Rd x 54 Tall, 304 Satin Stainless Steel US32D (630), 12 round mounting base plate (RB), Flat Recessed area for Intercom, ADA switch and Card Reader, Welded Dome Top (D) BPR10.75AINS32D 10.75 RD x 54 Tall, 304 Satin Stainless Steel US32D (630), Removable Bollard for In-ground mounting, Flat Recessed area for ADA switch and Card Reader, 1 Prep on the angle top for intercom, Welded Angle Top (AT) 5
The INGRESS R It s the logical choice. Achieve architectural integrity with ADA compliance all in one with the patented design, exclusive to Wikk! ingress\`in-gres\ n: 1. the act of entering 2. the power or liberty of entrance or access I36-3 Clear Clear Anodized Aluminum (628) with blue ADA logo & text 36 (914 mm) length by 2.5 (64 mm) width CENTER ACTUATION COLUMN 36 (914 mm) length by 6 (152 mm) width by 1.5 (38mm) depth CONTOURED BASE 6 (152 mm) TOP VIEW of STANDARD INGRESS R showing tapered profile 1 1 /2 (38 mm) depth 1.5 (36 mm) I36-5 DKBZ Dark Bronze Anodized Aluminum (710) with white ADA logo Shown on Bollard (Sold Separately) BPS SM-INGR DKBZ FEATURES and BENEFITS 36 TALL x 6 WIDE x 1 1 /2 DEEP (914 mm x 152 mm x 38 mm) Mounts on most wall surfaces including uneven Fits precisely on 6 (152 mm) x 6 (152 mm) bollard post when wall mounting is impractical Recommended mounting height is 3 (76 mm) from finished floor OPTIONS - STANDARD 1 = Plain, no legend 2 = Push to Open 3 = Push to Open 5 = Legend Colors: Blue on Clear, Brass and Stainless White on Dark Bronze Models without legends are available OPTIONS - CUSTOM Custom legends and lights Narrow widths and custom heights Finishes: Clear (628), Dark Bronze (710), US32D Satin Stainless (630), US32 Mirror Stainless (629), US4 Satin Brass (606 uncoated), US3 Mirror Brass (605 uncoated), US10B Dark Oxidized Satin Brass, oil-rubbed (613) For Custom INGRESS R see pages 8 & 9 SLEEK, TAPERED PROFILE Deflects impact from wheeled carts and conveyances Naturally directs movement toward central activation column No squared-off edges to get caught on Offers vandal deterrence: no gaps or edges to pry; ABS cap is secured by spanner screws Weather-resistant: no gaps for water or ice to penetrate; free draining Add switch transmitter and receiver for wireless activation (see pages 18 & 19) 6 The contoured profile of The INGRESS R allows activation from literally any approach and height level. RUGGED, YET SENSITIVE Dependable micro-switch: 15 amp, 125/250VAC, UL & CSA listed Sturdy, 1/8 (3 mm) extrusion (nominal) with superior finishes Actuates from literally all points on the activation column
delivers Trusted Innovation for more than10 years! Narrow INGRESS R I36-3 NAR Clear Clear Anodized Aluminum (628) with blue ADA logo & text The INGRESS R HARD-WIRE Conduit access points in base at 3 (76 mm) from top and 10 (254 mm) from bottom WIRELESS Option: Connect transmitter to wire harness and secure with double-sided tape near cap. 4.25 (108 mm) CAP 1.6 (41 mm) END VIEW of NARROW INGRESS R 4.25 (108 mm) wide at cap A 9 version of the INGRESS R can be used as a wall switch with a sleek, tapered design. Capped at both ends. I09-3 Clear Clear Anodized Aluminum (628) with blue ADA logo & text 4.25 (108 mm) with cap 1.6 (41 mm) Side View with cap By simply bumping the INGRESS R with the footrest of my wheelchair, I am able to activate the switch to open a door. It s such a clean, simple, truly functional solution and the end result is a welcoming design that leaves no one out, whether the building is modern, post-modern, or a historic restoration. Harold Dean Kiewel, AIA, CSI, CCS associate/sr. specifications writer, HMC Architects The vertical actuation bar also provides simplified door entry to a variety of people even those who simply have their hands full or are pushing a cart in many different settings like healthcare facilities and universities. Specified in: MasterFormat Section 08710 (08 71 20) Automatic Door Controls A 36 Column of Touch Activation The INGRESS R 7
CUSTOMIZE The INGRESS R Custom Options: Custom Legends: Numbers, Letters, Arrows or Symbols Custom Light Colors with black bezel: White Amber Blue Yellow Red Lights available in 28 volt or 120 volt Column of Touch Activation Custom Height: 9 to 42 tall I09-3 CLEAR 6 Wide x 9 Tall Clear Anodized Aluminum (628) ADA Legend I24-? CLEAR 6 Wide x 24 Tall Clear Anodized Aluminum (628) Custom Legend: OPEN DOOR and Door Open Symbol I30-? CLEAR 6 Wide x 30 Tall Clear Anodized Aluminum (628) Custom Legend: E I36-5AL DARK BRONZE 6 Wide x 36 Tall Dark Bronze Anodized Aluminum (710) ADA Legend and Arrow Left I42-3 CLEAR 6 Wide x 42 Tall Clear Anodized Aluminum (628) ADA Legend Finishes COLOR KEY These finish colors are printer s reproductions and may vary from actual colors. Call for samples. CLEAR (628) SATIN BRASS CLAD (606-uncoated) US4 DARK BRONZE (710) MIRROR BRASS CLAD (605-uncoated) US3 SATIN STAINLESS STEEL (630) US32D DARK OXIDIZED SATIN BRASS Oil Rubbed (613) US10B MIRROR STAINLESS STEEL (629) US32 8
delivers CUSTOMIZE The INGRESS R The challenge that Wikk was able to meet is delivering on an innovative approach that allows total access to someone in a wheelchair that really doesn t have the ability to push a button. And Wikk achieved it cost-effectively while ensuring that the switches were aesthetically pleasing. The INGRESS R Paul Baker, project manager with KONE on Wikk s INGRESS R customization capabilities Photo courtesy of ICORD Wikk s INGRESS R elevator cab and hall switches are featured in The Blusson Spinal Cord Centre the new home for the ICORD in the Vancouver General Hospital site in Vancouver, British Columbia, Canada. LIGHT INDICATES ELEVATOR ACTIVATION ELEVATOR ALARM CAB SWITCH ELEVATOR UP HALL SWITCH Other custom legends available. (Examples shown on page 8) We are also most pleased with the Wikk elevator solution in our building. It has been universally praised by all, from high cervical tetraplegics using sip-and-puff motorized wheelchairs, to the regular users of the building, to the Premier of BC and the Federal Minister of Health. A great success! Chris McBride, PHD Managing Director ICORD (International Collaboration On Repair Discoveries) 9
4x4 SERIES DOOR SWITCHES Standard Satin Stainless Steel US32D (630) CRAFTSMANSHIP combined with TECHNOLOGICAL INNOVATION PART NO. 4x4-1 4x4-2 4x4-3 LEGEND Blank No Legend (Black Infill) 4x4 Series Surface Mounts SURF SQ 4 & 6 BLK SHOWN WITH 4x4 SERIES SWITCH AND BATTERY (Sold separately) 4 19 /32 W X 4 19 /32 H X 1 3 /4 D (117 X 117 X 44 mm) 1 5 /8 Inside Depth (41 mm) Black ABS box with unique battery change-out compartment. Battery can be exchanged without switch removal. Tamper-resistant: compartment door is held in place by the switch and cannot be removed or lost. Switch mounting plate is recessed, presenting a finished appearance. Hard-Wire and Wireless 10 4x4-3AL 4x4-3AR 4x4-4 4x4-5 4x4-11 PRESS TO OPERATE (Black Infill) PUSH TO EXIT (Black Infill) 4x4 Series switches mount directly onto 1-gang prep of standard Wikk bollards. (See page 2 and 4 for bollard details.) See page 1 for switch cover materials, finishes, and options. GET THE EDGE SHOWN WITH SWITCH (Sold separately) Registered design; distributed by Wikk Industries 4x4 Edge US32D (630) 4 11 /16 H X 4 7 /8 W X 1 /2 D (118 X 124 X 8mm) Sturdy 3-sided stainless shroud to protect the switch components from harsh environmental conditions or in areas where walls are subjected to wash down chemicals. Especially effective against freezing rain and snow infiltration to prevent temporary ice buildup. Offers a decorative appeal by concealing the gap between the faceplate and backplate of the switch. Insert between the mounting surface and the backplate of the switch. Recommended for exterior applications. Hard-Wire and Wireless N4X4F FLUSH MOUNT 6 3 /4 W X 6 3 /4 H X 2 1 /8 D (172 X 172 X 54 mm) 5 X 5 Inside (127 X 127 mm) 1 7 /8 Inside Depth (47.6 mm) Durable black ABS enclosure, designed for mounting flush into hollow wall. Features a molded-in 7/8 (22mm) wide trim ring and mounting bracket. Includes required weatherresistant gasket plate. Hard-Wire or Wireless if mounted into RF-transparent wall materials. N4X4S SURFACE MOUNT 5 1 /2 W X 5 1 /2 H X 2 1 /8 D (140 X 140 X 54 mm) 5 X 5 Inside (127 X 127 mm) 1 15 /16 Inside Depth (49 mm) 2 1/8 (54mm) projection. 4X4 switch sits flush within this durable ABS enclosure, insuring a high degree of tamper-resistance. Includes required weather-resistant gasket plate. Hard-Wire or Wireless SURF 4/M 4 W X 4 H X 1 1 /8 D (102 X 102 X 29 mm) 1 1 /8 Inside Depth (29 mm) Clear (628) or Dark Bronze (710) Anodized Aluminum ring with plated mounting bracket. Similar to SURF 6/M shown on p. 12. Hard-Wire only
4R SERIES DOOR SWITCHES Standard Satin Stainless Steel US32D (630) 4R Series Surface Mounts Wik-Scutcheons WKS-4 US32D (630) 7 1 /4 Dia. (184 mm) 1 1 /4 overall height (30 mm) 1 Inside Depth (25 mm) Highly functional as it is decorative, this escutcheon offers a distinctive and tamper-resistant presence for the switch. The wall-hugging, slanted contour prevents snagging and shear-off from hand-propelled vehicles. Available in the same materials and finishes as AccessAbility switches. Part# WKS-4SS WRRING For weather resistance Hard-Wire only WKS-4 RF BLACK 7 13 /16 Dia. (200 mm) 1 9 /16 overall height (40 mm) 1 25 /64 Inside Depth (35.5 mm) A Wik-scutcheon in Radio Frequency (RF) transparent material. The same design and functionality as our metal escutcheon, but manufactured in textured, durable black ABS. This is an economical alternative with another advantage: wireless transmission. Features a rubber seal and caulking groove on the reverse side and a transmitter pocket. Can be painted to match décor. Part# WKS-4RF WRRING For weather resistance Hard-Wire and Wireless WKS-4RFWRRING Weather-Resistant Gasket Provide a self-sealing barrier from moisture or dirt entering cavity of mounts. Use in high infiltration conditions. Also available for WKS-4 US32D Part# WKS-4 SSWRRING SURF 4R 2 3 /4 W X 4 1 /2 H X 1 11 /16 D (70 X 114 X 43 mm) 1 9 /16 Inside Depth (40 mm) Brown phenolic box with corner-covering aluminum adapter plate to A WIKK EXCLUSIVE! SHOWN WITH SWITCH (Sold separately) BACK present a finished look. Micro-transmitter (SWTRAN-M series) fits neatly into mount. Hard-Wire and Wireless Wikk delivers CONSISTENT QUALITY Door Switches You Can Count On LEGEND Blank No Legend (Black Infill) PRESS TO OPERATE (Black Infill) 4R-1 4R-2 4R-3 4R-3AL 4R-4 PART NO. 4R-3AR 4R-5 4 SQUARE & ROUND SWITCHES N4RS SURFACE MOUNTED 5 Dia. X 2 1 /8 H (127 X 54 mm) 1 15 /16 Inside Depth (49 mm) 2 1 /8 (54mm) projection offers a distinctive presence. 4R switch sets flush within this good-looking, durable ABS enclosure, ensuring a high degree of tamper-resistance. Add N4WR gasket for weather-resistance. Hard-Wire and Wireless SHOWN WITH SWITCH (Sold separately) PUSH TO EXIT (Black Infill) 4R-11 N4RF FLUSH MOUNTED 5 7 /8 Dia. X 2 1 /8 H (149 X 54 mm) with trim ring 1 15 /16 Inside Depth (49 mm) Same material and qualities as N4RS, but designed for mounting flush into hollow wall. Features a molded-in 7 /8 (22 mm) wide trim ring and mounting bracket. Add N4WR gasket for weather-resistance. Hard-Wire or Wireless if mounted into RF-transparent wall materials. N4WR Weather-Resistant Gasket Provide a self-sealing barrier from moisture or dirt entering cavity of mounts. Use in high infiltration conditions. BACK 4R Series switches mount directly onto 1-gang prep of standard Wikk bollards. (See page 2 and 4 for bollard details.) See page 1 for switch cover materials, finishes, and options. 11
6x6 SERIES DOOR SWITCHES Standard Satin Stainless Steel US32D (630) 6x6 switches are the most cost-effective to stock: they mount to the three most typical junction boxes found on jobsites. PART NO. 6x6-1 6x6-2 6x6-3 6x6-3AL 6x6-3AR 6x6-4 LEGEND Blank No Legend (Black Infill) PRESS TO OPERATE (Black Infill) 6x6 Series Surface Mounts SHOWN WITH 6x6 SERIES SWITCH AND BATTERY (Sold separately) SURF SQ 4 & 6 BLK 4 19 /32 W X 4 19 /32 H X 1 3 /4 D (117 X 117 X 44 mm) 1 5 /8 Inside Depth (41 mm) Black ABS box with unique battery change-out compartment. Battery can be exchanged without switch removal. Tamper-resistant: compartment door is held in place by the switch and cannot be removed or lost. Switch mounting plate is recessed. 6x6 switch cover extends 3/4 (19 mm) beyond mount on all sides. Hard-Wire and Wireless Registered design; distributed by Wikk Industries 6x6-5 SURF 6/M 4 W X 4 H X 3 /4 D (102 X 102 X 19 mm) 3/4 Inside Depth. (19 mm) 6x6 Series switches mount directly onto 1-gang prep of standard Wikk bollards. (See page 2 and 4 for bollard details.) See page 1 for switch cover materials, finishes, and options. Clear (628) or Dark Bronze (710) anodized aluminum ring surrounds galvanized mounting plate to create an attractive surface mount. 2-piece unit. Hard-Wire only See pages 18 & 19 for wireless options 12
6R SERIES DOOR SWITCHES Standard Satin Stainless Steel US32D (630) Wik-Scutcheons 6R Series Surface Mounts A WIKK EXCLUSIVE! WKS-6 US32D (630) 9 1 /2 Dia. (241 mm) 1 overall height (25 mm) 7/8 Inside Depth (22 mm) Highly functional as it is decorative, this escutcheon offers a distinctive and tamper-resistant presence for the switch. The wall-hugging, slanted contour prevents snagging and shear-off from hand-propelled vehicles. Available in the same materials and finishes as AccessAbility switches. Hard-Wire only SURF 6R 4 19 /32 W X 4 19 /32 H X 1 3 /4 D (117 X 117 X 44 mm) 1 1 /2 Inside Depth (38 mm) Surf SQ 4 & 6 BLK black ABS box with aluminum corner-covering adapter plate to present a finished appearance. Features a unique battery change-out compartment. Battery can be exchanged without switch removal. Tamper-resistant: compartment door is held in place by the switch and cannot be removed or lost. Hard-Wire and Wireless N6RS SURFACE MOUNTED 6 7 /16 Dia. X 2 1 /8 H (164 mm X 54 mm) 1 15 /16 Inside Depth (49 mm) 2 1 /8 (54 mm) projection offers a distinctive presence. 6R switch sets flush within this good-looking, durable ABS enclosure, ensuring a high degree of tamper-resistance. Add N6WR gasket for weather-resistance. Hard-Wire and Wireless N6RF FLUSH MOUNTED 7 3 /4 Dia. X 2 1 /8 H (197 X 54 mm) with trim ring 1 7 /8 Inside Depth (48 mm) Same material and qualities as N6RS, but designed for mounting flush into hollow wall. Features a molded-in 7/8 (22 mm) wide trim ring and mounting bracket. Add N6WR gasket for weather-resistance. Hard-Wire or Wireless if mounted into RF-transparent wall materials. N6WR Weather-Resistant Gasket Provide a self-sealing barrier from moisture and dirt entering cavity of mounts. Use in high infiltration conditions. SHOWN WITH SWITCH (Sold separately) FRONT SHOWN WITH 6R SERIES SWITCH AND BATTERY (Sold separately) LEGEND Blank No Legend (Black Infill) PRESS TO OPERATE (Black Infill) BACK 6R Series switches mount directly onto 1-gang prep of standard Wikk bollards. (See page 2 and 4 for bollard details.) See page 1 for switch cover materials, finishes, and options. PART NO. 6R-1 6R-2 6R-3 6R-3AL 6R-3AR 6R-4 6R-5 13 6 SQUARE & ROUND SWITCHES
AA SERIES SWITCHES (Narrow All-Active) Standard Satin Stainless Steel US32D (630) FEATURES: 1 11 /16 W x 4 1 /2 H (43 x 114 mm) Designed to flush-mount directly into narrow jambs; no junction box needed Compatible with a Jamb Surface Box (JSB) Cutout and drill/tap template included Requires custom bollard prep Hard-Wire and Wireless See page 1 for switch cover materials, finishes, and options. PART NO. AA-1 AA-2 AA-3 AA-3 AL AA-3AR LEGEND (Debossed and Filled) Blank No Legend (Black Infill) ARROW LEFT ARROW RIGHT (Blue Infills) Revolving Door Switch Designed to mount to the leading jamb of an automatic revolving door. When activated, the revolution speed slows to allow passage of slow-moving people. Raised Braille text reads the same. AA-PTSLOW Braille Cutout and drill/tap template included. Compatible with Jamb Surface Box (JSB). Requires custom bollard prep Hard-Wire and Wireless Horizontal Switch Specifically designed for applications within narrow horizontal mullions or curtain AA-3H wall framing. Flush-mount directly into mullions and framing. Cutout and drill/tap template included. Compatible with Jamb Surface Box (JSB) Requires Custom Bollard prep. Hard-Wire and Wireless AA-3AL x AA-3AR Vestibule Switch Designed to independently operate 2 doors on opposite sides of a vestibule. Flush mounts to double gang electrical box with 2-device surface ring and surface mounts to Wikk s SURF SQ 4 & 6 BLK or SURF 4M and BPS SM-DGANG prep. Hard-Wire and Wireless AA-5 AA-5BRL SHOWN WITH SWITCH (Sold Separately) JSB (Jamb Surface Box) PRESS (in Braille) SURFACE MOUNT for Narrow Switches 1 3 /4 W X 4 9 /16 H X 1 3 /4 D (44 X 116 X 44 mm) 1 5 /8 Inside Depth (41 mm) Narrow style box in sturdy black ABS Micro-transmitter (SWTRAN M series) fits neatly into box Self-adhesive mounting template included Hard-Wire and Wireless Square Maintained Key Switch and AA-3 Combination A combination switch featuring an AA and a maintained 1 pole key switch to offer a neat, orderly solution for access and security. The 4 1 /2 x 4 1 /2 back plate serves as the mounting plate, ready for flush mounting directly to a double gang electrical box with 2-device surface ring and surface mounts to Wikk s SURF SQ 4 & 6 BLK 4 1 /2 X 4 1 /2 (144 X 144 mm) or SURF 4M and BPS SM-DGANG prep. You may choose your AA legend and the finish to customize the installation. KSM1-4xAA-3 US32D Hard-Wire and Wireless 14
SFA SERIES SWITCHES (Single Gang Full-Active) Standard Satin Stainless Steel US32D (630) FEATURES: Fits all single gang (2 x 4) flush electrical boxes Use SURF SFA mount for surface or wireless applications Mount directly onto Wikk Square Bollards Hard-Wire and Wireless See page 1 for switch cover materials, finishes, and options. 2 3 /4 W x 4 1 /2 H (70 x 114mm) PART NO. SFA-1 SFA-2 SFA-3 LEGEND (Debossed and Filled) Blank No Legend (Black Infill) NARROW & STANDARD SWITCHES Paramount Switch 3 3 /4 W x 5 1 /2 H x 5 /8 D (96 x 140 x 16 mm) Upscale actuator switch with escutcheon plates becomes a fixture. The perfect design match for ornate buildings and historic renovations. Finishes available: US32D Satin Stainless (630) US32 Mirror Stainless (629) US4 Satin Brass (606-Uncoated) US3 Mirror Brass (605-Uncoated) US10B Dark Oxidized Satin Brass Paramount Switch oil-rubbed (613) US32D (630) Projects.625 (16 mm) from mounting surface. Standard Legends and Custom available. Hard-Wire Paramount Switch with Cuff 5 1 /2 W x 7 1 /4 H x 2 7 /32 D (140 x 184 x 56 mm) SFA-5 SURFACE MOUNT for Single Gang Switches SURF SFA 2 3 /4 W X 4 1 /2 H X 1 5 /8 D (70 X 114 X 41 mm) 1 1 /2 Inside Depth (38 mm) Single-gang size brown phenolic box. Micro-transmitter (SWTRAN M series) fits neatly into mount. Weather-resistant SFA requires SURF 4R box with adapter plate (see Page 11). Hard-Wire and Wireless Paramount US32 (629) with Cuff Paramount US10B (613) with Cuff Projects 2 7 /32 (56 mm) from mounting surface. SHOWN WITH SWITCH (Sold Separately) 15
NARROW & SINGLE GANG KEY SWITCHES Standard Satin Stainless Steel US32D (630) NARROW Key Switches 1 11 /16 W x 4 1 /2 H (43 x 114mm) KS-N KSM1N OOH PART NO. KS1N STYLE Maintained contact Access control where security is not a factor Bi-colored LED indicates power ON or HOLD-OPEN (available in green/amber, red/blue and green/red)) Key can be set in ON, HOLD-OPEN or OFF position only Key can be removed while in any operating mode SINGLE GANG Key Switch 2 3 /4 W x 4 1 /2 H (70 x 114mm) KS-P Mounting depths vary from 7/8-1-1/4 (22 x 32mm)depending on switch function and cover plate size WIRELESS OPTION KS2N KSM1N KSM2N KSM1N OOH KSM1N OOH PART NO. KS1P WIRELESS OPTION KS2P KSM1P KSM2P KSM1P OOH KSM2P OOH 1 pole, Momentary Contact 2 pole, Momentary Contact 1 pole, Maintained Contact 2 pole, DPDT Maintained Contact 1 pole, Maintained Contact On/Off/Hold Open with Light 2 pole, Maintained Contact On/Off/Hold Open with Light STYLE 1 pole, Momentary Contact 2 pole, Momentary Contact 1 pole, Maintained Contact 2 pole, Maintained Contact 1 pole, Maintained Contact On/Off/Hold Open with Light 2 pole, Maintained Contact On/Off/Hold Open with Light SURFACE MOUNT for Narrow Key Switches JSB (Jamb Surface Box) 1 3 /4 W X 4 9 /16 H X 1 3 /4 D (44 X 116 X 44 mm) 1 5 /8 Inside Depth (41 mm) Narrow black ABS box accommodates wired or wireless operations Self-adhesive mounting template included Hard-Wire and Wireless SURFACE MOUNT for Single Gang Key Switches SURF 4R 2 3 /4 W X 4 1 /2 H X 1 11 /16 D (70 X 114 X 41 mm) 1 9 /16 Inside Depth (40 mm) Single gang brown phenolic box with corner-covering aluminum adapter plate to present a finished look. Micro-transmitter (SWTRAN-M series) fits neatly into mount. Hard-Wire and Wireless 16 Fits 1-Gang mount or prep Mount directly onto Wikk square bollards PUSH BUTTON SWITCHES SINGLE GANG Push Button Switches SPB Series 2 3 /4 W x 4 1 /2 H (70 x 114mm) Mounts to standard Single Gang Box self-adhesive label included Choice of logo or no logo, red or black button Not available as weather-resistant NARROW Push Button Switches N/S Series 1 11 /16 W x 4 1 /2 H (43 x 114 mm) Mounts to JSB Box self-adhesive label included Choice of logo or no logo, red or black button Self-adhesive mounting cutout and drill/tap template included Not available as weather-resistant SPB-1 BLK N/S-1 BLK SPB-5 RED N/S-5 RED
SQUARE KEY SWITCHES Standard Satin Stainless Steel US32D (630) SQUARE Key Switch PART NO. KS1-4 WIRELESS OPTION KS2-4 KSM1-4 KSM2-4 KS-4 KSM1-4 OOH KSM2-4 OOH 4 1 /2 x 4 1 /2 (114 x 114 mm) Fits 1- or 2-gang mount or prep Mount directly onto Wikk square bollards Includes dummy screws and nuts to present finished appearance STYLE 1 pole, Momentary Contact 2 pole, Momentary Contact 1 pole, Maintained Contact 2 pole, DPDT Maintained Contact 1 pole, Maintained Contact On/Off/Hold Open with Light 2 pole, Maintained Contact On/Off/Hold Open with Light SQUARE Maintained Key Switch and AA-3 Combination KSM1-4XAA-3 PART NO. KSM1-4xAA-3 A combination switch featuring an AA and a maintained 1 pole key switch to offer a neat, orderly solution for access and security. The 4 1 /2 x 4 1 /2 back-plate serves as the mounting plate, ready for flush mount directly to a double gang electrical box with 2-device surface ring or surface mount to Wikk s SURF 4/M, SURF SQ 4 & 6 BLK, and Square Bollards (requires 2-gang prep). You may choose your AA legend and the finish to customize the installation. STYLE 1 pole, Maintained Contact with AA-3 Switch Attached (Other AA legends may be used) SHOWN WITH KSM1-4xAA-3 SWITCH AND BATTERY (Sold separately) SURFACE MOUNTS for Square Key Switches SURF SQ 4&6 BLK 4 19 /32 W X 4 19 /32 H X 1 3 /4 D (114 X 114 X 44 mm) 1 5 /8 Inside Depth (41 mm) Black ABS box with unique battery change-out compartment. Battery can be exchanged without switch removal. Tamper resistant: compartment door is held in place by the switch and cannot be removed or lost. Switch mounting plate is recessed, presenting a finished appearance. Hard-Wire and Wireless Registered design; distributed by Wikk Industries N4X4F FLUSH MOUNT 6 3 /4 X 6 3 /4 X 1 7 /8 O.D. (172 X 172 X 47.6 mm) 5 X 5 Inside (127 X 127 mm) 1 7 /8 Inside Depth (47.6 mm) Durable black ABS enclosure, designed for mounting flush into hollow wall. Features a molded-in 7/8 (22mm) wide trim ring and aluminum mounting bracket. Includes a required weatherresistant gasket plate. Hard-Wire or Wireless if mounted into RF-transparent wall materials. N4X4S SURFACE MOUNT 5 1 /2 W X 5 1 /2 H X 1 7 /8 D (140 X 140 X 54 mm) 5 X 5 Inside (127 X 127 mm) 1 15 /16 Inside Depth (49 mm) 2 1/8 (54mm) projection. 4X4 switch sets flush within this durable ABS enclosure, insuring a high degree of tamper-resistance. Includes a required weather-resistant gasket plate. Hard-Wire or Wireless SURF 4/M 4 X 4 X 1 1 /8 O.D. (102 X 102 X 29 mm) 1 1 /8 Inside Depth (29 mm) Clear (628) or Dark Bronze (710) Anodized Aluminum ring with plated mounting bracket. Hard-Wire only KEY & BUTTON SWITCHES FEATURES: Heavy duty compact block and switch assembly 1 satin chrome mortise cylinder with standard Adams Rite cam and Schlage C keyways All locks keyed alike (Stainless switches only) Fully assembled with cylinder intact Complete parts kit includes: 2 keys, terminal connectors, stainless Phillips screws, stainless tamper-resistant screws, and set-screw wrench (for cylinder exchange) Rated 6 amps at 125 VAC, 3 amps at 250 VAC (1 PDT Momentary rated 5 amps at 120 VAC, 2 amps at 250 VAC) OPTIONS: Decorative materials and finishes (see page 1) Custom engraving upon request Wikk Wireless on single pole momentary switches (see pages 18-19 for transmitters) May be ordered without cylinder (Add suffix -CYL ) On/Off/Hold Open available without light (Add suffix -LIGHT ) Key Cylinder Adapter Plate for spacing of different sized cylinders. Key Cyl Adapter 17
Add Remote Control Versatility with Wikk Wireless is a complete line of advanced radio control products. Wikk Signature 433 Products are known for advanced rolling code technologies for high security application, improved range and longevity. Wikk Wireless provides a variety of styles and frequencies to accommodate your requirements: Switch-operated Hand-Held Hands-Free Key-Free SIGNATURE 433MHz LINE Programmable products are only compatible within Wikk products. 433MHz Receiver Rec1Channel433 1 1 /4 W X 2 H X 3 /4 D (32 X 51 X 19 mm) 433MHz Vestibule Sequencer RECVESTSEQ 433 4 1 /8 W X 3 /4 H X 1 1 /8 D (105 X 44 X 29 mm) 1 Channel Holds 85 Transmitter Codes 12-24 volt AC or DC Adjustable Time Hold Individually authorized codes for increased security Compatible with all Transmitters on this page Also available: Rec2Chan Ext 433 with 2 Relays Transmitters sold separately. Utilizing operator power, this receiver signals the second door conserving transmitter battery power. Requires two receivers for two-way sequencing. Vestibule Sequencer compatible with all Transmitters on this page SWTRAN 433 1 9 /64 W X 15 /16 H X 7 /32 D (29 X 49 X 6 mm) not including wiring and battery Pre-wired for quick installation One model fits all Antenna magnifies signal 9 Volt battery included Compatible with Wikk 433 Receivers 433MHz Switch & Bollard Transmitter For Bollard use, tuck under rubber strap on Wikk standard black bollard cap (non-metallic) 433MHz Hand-Held & Keychain Transmitters Each button operates one channel 1TRANSL433 3 1 /4 W X 1 7 /8 H X 5 /8 D (83 X 48 X 16 mm) 1TRANSM433 2 13 /32 W X 1 13 /32 H X 1 /2 D (61 X 36 X 13 mm) Includes Keychain 433MHz Personal Key-Free Transmitter PKF 433 2 3 /8 W X 3 1 /2 H X 1 1 /16 D (60 X 89 X 27 mm) 2TRANSL433 3 1 /4 W X 1 7 /8 H X 5 /8 D (83 X 48 X 16 mm) 2TRANSM433 2 13 /32 W X 1 13 /32 H X 1 /2 D (61 X 36 X 13 mm) Includes Keychain Activated by light touch Buzzer indicates transmission CR123A battery included Indoor or outdoor use Compatible with Wikk 433 Receivers 4-button transmitters also available Compatible with Wikk 433 Receivers 18
300MHz A unique battery-saving feature cuts off power after 10 seconds if switch is continually pressed. 2 Channel Receiver Dual Frequency and Power Compatibility Handles 300/310MHz (Multi-Code and Linear compatible) (Frequency recognition by jumper setting) Auto-sensing 12-24 Volts AC or DC 2 channel model: 10 DIP switches REC2CHAN300/310 3.6 W x 4.25 H x 1.5 D (91 X 108 X 38 mm) Hand-Held & Keychain Transmitters Each button operates one channel. 1TRANSM300 1 1 /2 W X 2 H X 1 /2 D (38 X 51 X 12 mm) 2TRANSM300 1 1 /2 W X 2 H X 1 /2 D (38 X 51 X 12 mm) WIRELESS Supplied with: 9 pin connector and color-coded wiring harness 9.5 inch (241 mm) 75 Ohm Whip Antenna 1TRANSL300 3.13 W X 1.75 H X.5 D (80 X 45 X 13 mm) 2TRANSL300 3.13 W X 1.75 H X.5 D (80 X 45 X 13 mm) 12 Volt Battery - Type 23A (Included) 4-button transmitters also available Switch and Bollard Transmitter Part# SWTRAN300M 1 3 /8 W X 1 3 /4 H X 1 /8 D (35 X 44 X 3 mm) 10 DIP switch models Handles 300MHz (Multi-Code) 9 Volt Battery included For Bollard use, tuck under rubber strap on Wikk standard black bollard cap (non-metallic) One Model Fits All Switches! Wikk also supports 310MHz products - 8 DIP Switch Models RFID 433MHz RFID 433MHz Receiver Holds 30 codes Individually authorized codes for increased security Adjustable to range 3-50 ft. Automatic shut-down after 4 seconds or no motion of transmitter. RFID Hands-Free Transmitter Integrates with any brand/model of access control system (WG model) Pocket/purse/bag model Ideal for clean rooms, operating rooms, assisted living centers, residential, or simply where the convenience or necessity of hands-free access control is preferred RECEIVER Receiver mounts adjacent to the door 45-50 AFF (recommended) and is wired to the operator. RFID 433 REC WG 3.5 W X 2.4 H X.9 D (89 X 61 X 23 mm) 26-bit Wiegand output RFID 433 AUTOSIG 2.75 W X 1.4 H X.35 D (70 X 36 X 9 mm) Automatic signaling CR 2032 3 volt battery included Compatible with RFID 433 Receivers RFID 433 AUTOSIG RFID 433 REC 1D 3.5 W X 2.4 H X.9 D (89 X 61 X 23 mm) For single door RFID 433 1TRANS 2.75 W X 1.4 H X.35 D (70 X 36 X 9 mm) COVER NOTE: Do not place near metal Manual signaling CR 2032 3 volt battery included Compatible with RFID 433 Receivers RFID 433 1TRANS 19
CUSTOM DESIGNED SWITCHES Wikk is well-known and respected for its custom design and manufacturing capabilities and timely shipping. Standard lead time is 2-3 weeks for Custom Switches. Custom Wall Switches available: Custom Design/Engraving and Braille Special Materials and Finishes Finishes US32D Satin Stainless (630) US32 Mirror Stainless (629) US4 Satin Brass (606 uncoated) US3 Mirror Brass (605 uncoated) US10B Dark Oxidized Satin Brass oil-rubbed (613) We look forward to creating your special switch, whether it requires a distinctive finish, logo, image, text, or simply a different infill color! Wikk manufactures Grade 2 Braille as per ADA regulation. Please refer to your local codes for city and state compliance. Don t see your design here? Ask your local distributor about Wikk custom products. 20
TOUCHLESS SWITCH No Touch Wave-to-Activate Switch For Sanitary Entry/Exit applications DPDT Dry Contact Output No Moving Parts Bi-color Status Illumination Interior Application SFA NO TOUCH 32D Side View 4x4 NO TOUCH 32D FrontView Features & Applications Uses IR Sensor technology; device is active with the simple wave of a hand Designed to control electric locks/strikes, magnetic locks, or automatic door operators Ideal for use in sanitary applications such as cleanrooms, bathrooms, food processing, hospitals and labs. Sensing Range up to 4" (10cm) Mounted on a durable stainless steel plate Dual LED, illuminated sensor, Red/Green indicates Inactive/Active status Quick connect screwless terminal block for easy installation Mounts to standard single gang electrical box Specifications Input: 25mA (standby); 55mA (Active) @ 12/24VDC Output: 2-SPDT, 3 Amp Dry Contact Activation Time: 1 second or as long as sensor is triggered LED Color: Standby RED; Active Green Range: 4" (10cm) Weight: 3 oz. (85g) Dimensions: 4.5" x 2.75" x 1.375" (115 x 70 x 35mm) Temperature Rated: - 4º F to 131º F CUSTOM DESIGN and TOUCHLESS SWITCHES MISCELLANEOUS PRODUCTS Alternate SWITCHING ACCESSORIES SEQUENCE & LOCK RELAY SEQ. & LOCK RELAY This device is used between the actuating switch and the door operator to create a momentary delay, allowing an electric strike or electric panic device to release before the door begins to open. Also can be used as a hard-wire vestibule sequencer. 1 3 /4 L x 2 1 /2 W x 1 H Installation TOOLS HEX WRENCHES These hex wrenches have an ergonomic 3-sided handle for a comfortable grip, and are used to install AccessAbility switches to junction boxes and surface mounts. One tool is included with every 20 switches ordered, and are also available for purchase. PT-5/64 - (blue) used to mount switch to 1 & 2 gang configurations using a 6-32 screw PT-3/32 - (white) used to mount 6 switches to 4x4 configurations using an 8-32 screw ALTERNATE ACTION RELAY ALT ACT'N RELAY This device is an impulse relay used to change the normal momentary action of a wall switch to maintained, for Push to Open and Push to Close door operator activation. With 2 mounting brackets. 1 7 /8 L x 1 5 /8 W x 2 7 /8 H SPANNER BIT for INGRESS R This Spanner Bit is used to remove and install #8 security spanner bit screws on the INGRESS R switch located on the top of the INGRESS R cap. One bit is included with the purchase of 1-3 INGRESS Rs. Additional bits are available for purchase. #8 SPANNER BIT 21
Bollard Solutions NEW BPSSM OUTLETCLR 6 x 6 x 24 Tall, Clear Anodized Aluminum (628), Surface mount, 1 prep for electrical outlet Removable ABS cap BPD6 SM INR US32 6 RD x 42 Tall, 304 Mirror Stainless Steel US32 (629) Recessed area for flat devices, Reveal (R) for a decorative touch, Welded Dome Top (D) BPR SM AINS PCDB 6 RD x 48.625 Tall, Mill Aluminum, powder coated (PC) to match Dark Bronze Aluminum concealed mounting base, Recessed area for ADA switch and card reader on the angle top, Welded Angle Top (front slant) (AT) BPRTFSM126 PCCL 12 x 6 x 54 Tall, 5 ga. Formed Mill Aluminum, Powder coated (PC) to match Clear Aluminum, concealed mounting base, 3 preps for devices, Welded Flat Top (FT) BPD6SMINR PCRED 6 Rd x42 Tall, Mill Aluminum, powder coated (PC) in Red- RAL3020, concealed mounting base, Recessed area for flat devices, 1/4 Reveals (R) in two areas for a decorative touch, Welded Dome Top (D) BPS SM CLAD US10B with I36-3 US10B 6 x 6 x 42 Tall, US10B Dark Oxidized Satin Brass, oil-rubbed (613), concealed mounting base, 1 prep for INGRESS R ADA switch, I36-3 US10B with gold logo, Removable Black ABS cap U.S. Representatives Visit the website: www.wikk.com/contactus.html to find a Representative in your area Canadian Stocking Distributors Visit the website: www.wikk.com/contactus.html CORPORATE HEADQUARTERS Local Phone: 414.421.9490 Local Fax: 414.421.3158 Toll Free: 877.421.9490 Toll Free Fax: 877.421.3158 www.wikk.com P.O. Box 167 6169A Industrial Court Greendale, WI 53129-0167 United Kingdom Stocking Distributor Controls For Doors, LTD Hurst Place, Woldingham Rd. Woldingham, Surrey, England CR3 7AF www.cfdltd.com Mr. Kieran Lewis sales@cfdltd.com Phone: 01.883.652652 Fax: 01.883.652055 Distributed by: MEMBER OF: 01 2014 Printed in U.S.A.