Dolan Mechanical, Inc. 638 Johnson Road, PO Box 326 Sicklerville, NJ 08081 (856) 629-9331 FAX (856) 629-6545 TO: Imad Haq PROJECT NAME: Philadelphia International Airport Concourse B HVAC Renovation & Replacement - Mechanical CONTRACT: Mechanical PHL-1520.16 SPECIFICATION SECTION: 232123 ITEM DESCRIPTION: Hydronic Pumps MANUFACTURER: Armstrong SHOP DRAWING REVIEW REVIEW IS FOR GENERAL CONFORMANCE WITH DESIGN INTENT. SEE SUBMITTALS SECTION IN SPECIFICATIONS FOR SPECIFIC CONDITIONS THAT APPLY TO THIS REVIEW. NO EXCEPTION TAKEN MAKE CORRECTIONS NOTED SUBMIT SPECIFIED ITEM REVISE AND RESUBMIT REJECTED ACCEPTED INFO ONLY SHOP DWG. 232123- SUBM. 1 X JOB 2015-127 BY DATE EL BURNS ENGINEERING, INC. 2016-11-3 APPROVED DOLAN MECHANICAL, INC. SUBMITTAL # 16-232123-001 BY DAT E 11/01/16 Stephen L. Agozzino, Vice President APPROVED APPROVED AS NOTED REVISE AND RESUBMIT DISAPPROVED Failure to comply exactly with the notations on the attached submittal will constitute in non-approval of same. Contractor is required to comply with all Contract Documents. DIVISION OF AVIATION ENGINEERING REVIEWED BY: DATE: 11/16/2016 PUMPS MEET REQUIREMENTS AND ARE ACCEPTED. HOWEVER, RESUBMIT FOR RECORD P-1 AND P-2 PUMP CURVES SINCE IT INDICATES WATER NOT 30% ETHYLYNE GLYCOL.
BLANKIN EQUIPMENT 489 Shoemaker Road King of Prussia PA 19406 Submittal 215-229-7400 Fax 215-228-2560. Prepared For: Dolan Mechanical Date: 10-26-2016 Job Name: PHL Concourse B Prepared By: Brandon Zee Lang Products Included in this Submittal Package: Qty Description (2) Armstrong 4600 8x6x10L pumps (P-1,2) (2) Armstrong 4030 4x3x10 pumps (P-3,4) The attached information describes the equipment we propose to furnish for this project, and is submitted for your approval. Blankin Equipment 489 Shoemaker Road King of Prussia PA 19406 215-229-7400 Fax 215-228-2560
489 Shoemaker Road King of Prussia, PA 19406 Phone: 2152297400 Fax: 2152282560 Web Address: www.blankinequipment.com SUBMITTALS FOR APPROVAL Reference No. 16-00000058 To: Dolan Mechanical Attn: Steve 638 Johnson Road Sicklerville, NJ 08081 Date: 10/26/2016 Job Name: Philadelphia International Airport - Concourse B HVAC Renovation Job Engineer: Burns Engineering We are pleased to submit on the following equipment. Armstrong Centrifugal Pump(s) Specification Section [P-1,2] Quantity (2) Armstrong Centrifugal Pump(s), Model 4600-8x6x10L Base Mounted, Horizontal Split-Case, Double Suction Pumps. Coupled to 200 HP, 3600 RPM, 480/3/60, TEFC motors. Based on 2,150 GPM @ 250' TDH each Base Price Includes - Bronze-Fitted Construction (Bronze Impeller) - Cast Iron Casing with Fabricated Steel Baseplate - Flexible Coupling, with OSHA Guard - Carbon Steel Shaft w/ 304 Stainless Steel Shaft Sleeve - Mechanical Seal w/ Carbon Rotating Face and Silicon Carbide Seat (Free Upgrade From Standard Carbon Seal - EXTRA LONG LIFE) - Bronze Casing Wear Rings ROTATION ORIENTATION - Must Be Confirmed Prior To Ordering NEMA Premium Efficiency Inverter Ready Rated Pump Motor VFD Rated Pump Coupling Field Alignment P-1,2,3,4 Spare Mechanical Seals 9975000-997 [P-3,4] Quantity (2) Armstrong Centrifugal Pump(s), Model 4030-4x3x10 Date: 10/26/2016 Reference No. 16-00000058 Page 1 of 2
Base Mounted, End Suction Pumps. Coupled to 75 HP, 3600 RPM, 208/3/60, TEFC motors. Based on 695 GPM @ 260' TDH each Base Price Includes - Bronze-Fitted Construction (Bronze Impeller) - Cast Iron Casing with Fabricated Steel Baseplate - Flexible Coupling, with OSHA Guard - Carbon Steel Shaft w/ 304 Stainless Steel Shaft Sleeve - Mechanical Seal w/ Carbon Rotating Face and Silicon Carbide Seat (Free Upgrade From Standard Carbon Seal - EXTRA LONG LIFE) VFD Rated Pump Coupling Spare Mechanical Seals 975000-984 NEMA Premium Efficiency Inverter Duty Rated Pump Motor Submitted By: Blankin Brandon Lang Date: 10/26/2016 Reference No. 16-00000058 Page 2 of 2
Submittal Ref. #: 503840.1 rev6 Horizontal split case pump Model: Series 4600-8x6x10L-200 hp Pump (Motor supplier: Armstrong choice) Project name: 16-0058 - Philadelphia Airport - Concourse B Location: Representative: Blankin Equipment Corporation Date submitted: 10/20/2016 12:19:36 PM Phone number: Engineer: e-mail: blang@blankinequipment.com Contractor: Submitted by: Brandon Lang Application design data Tag number: P-1,2 Pipe orientation: Single Suction pressure: Location: Fluid: Water: Quantity: 2 Operating temperature: 60 F Duty flow per pump: Duty head: Total dissolved solids: Materials of construction 2150 USgpm 250 ft 0 ppm Viscosity: 0 ft 31 SSU Specific gravity: 1.0000 Construction: BF Impeller: Bronze (B584-844) Rating: ANSI-125 Pump shaft: Carbon Steel (C1045-100) Connections: Inlet: 8 in, Outlet: 6 in Shaft sleeve: Bronze (B584-932) Casing (volute): Cast Iron (A48-30) Flush line: Braided Stainless Steel Bearings: Anti-Friction Grease Lubricated Casing gasket: Velotherm (Non-Asbestos fiber) Mechanical seal data Pump suction: Right-hand when viewed from Drive End Seal type: Inside Single Spring Rotating face: Resin Bonded Carbon Manufacturer code: 21A Stationary seat: Silicon Carbide Springs: Stainless Steel Secondary seal: EPDM Rotating hardware: Motor electrical data Stainless Steel Supplier: Factory Choice Insulation class: Class F Insulation Size: 200 hp Inverter motor type: Inverter Duty Frame number: 447TSC Efficiency: NEMA Prem (12.12) Enclosure: TEFC Speed: 3580 rpm Motor Electrics: 480/3/60 Operating limits (temperature - pressure) Maximum pressure: 175 psi Maximum temperature: 225 F Pump casings are hydrostatically tested to 150% of maximum pump working pressure rating. www.armstrongfluidtechnology.com 10/26/2016, Ref. # 503840.1 rev6 Page 4 of 20
Performance curve Head (ft) 480 10.00 in38 400 320 240 160 80 8.84 in 7.63 in 52 64 Series 4600 8x6x10L @ 3580 rpm 72 System 78 81 82 81 100 hp 300 hp 250 hp 52% 200 hp 150 hp 125 hp 0 0 0.8 1.6 2.4 3.2 4 4.8 78 72 64 PT154-2-0 (3.23.0.1) ANSI/HI 14.6.3.4 1B --- Admin Data --- Tag Num: P-1,2 Location: --- Motor Data --- Motor Size: 200 hp Motor Speed: 3600 rpm --- Design Duty Point --- Flow: 2150 usgpm Head: 250 ft Impeller: 8.84 in --- Performance Data --- NPSHR: 31.8 ft Eff. @ Design: 76.48 % BHP @ Design: 177.48 hp Mtr Capability @ Rated Spd: 200.00 hp %Mtr Safety: 12.69% BEP @ Design Imp.: 76.49 % @ 2143.4 usgpm Impeller Max BHP @ Flow: 185.54 hp @ 2636.4 usgpm %max imp. range: 51.16 % Outlet Velocity: 23.88 ft/s VFD Setting: 60.0 Hz Water:, spgr= 1.0000 Flow ( 1,000 usgpm) Head (ft) 400 Series 4600 8x6x10L @ 8.84 in PT154-2-0 (3.23.0.1) ANSI/HI 14.6.3.4 1B --- Admin Data --- Tag Num: P-1,2 Location: 320 240 160 80 3580 rpm 3080 rpm 2580 rpm 2080 rpm 1580 rpm 68 System 73 76 77 76 hp 125 hp150 100 hp 200 hp 1074 rpm 75 hp 60 hp 0 0 0.8 1.6 2.4 3.2 4 Water:, spgr= 1.0000 50 60 73 68 60 Flow ( 1,000 usgpm) --- Motor Data --- Motor Size: 200 hp Motor Speed: 3600 rpm --- Design Duty Point --- Flow: 2150 usgpm Head: 250 ft Impeller: 8.84 in --- System Intersect Data --- 1. System @ 60.0 Hz: 2150 @ 250, 177.48 hp 2. System @ 51.6 Hz: 1850.1 @ 185.1, 113.08 hp 3. System @ 43.2 Hz: 1549.7 @ 129.9, 66.46 hp 4. System @ 34.9 Hz: 1249.3 @ 84.4, 34.82 hp 5. System @ 26.5 Hz: 949.2 @ 48.7, 15.27 hp 6. System @ 18.0 Hz: 645.2 @ 22.5, 4.8 hp www.armstrongfluidtechnology.com 10/26/2016, Ref. # 503840.1 rev6 Page 5 of 20
Dimensional data (not for construction) Side view Top view Weight: 2728 lb Not to scale Units of measure : inches [millimeters] Tolerance of ± 0.125 inch (± 3 mm) should be used For certified dimensions, please contact your Armstrong representative Pump equipped with casing drain plug and ¼ inch NPT suction and discharge gauge ports Connection details Connection Size Rating OD Bolt quantity* BCD Bolt size Inlet 8 ANSI-125 13.5 8 11.75 0.75 Outlet 6 ANSI-125 11 8 9.5 0.75 *Equally spaced straddling centreline Special instructions The program has defaulted to a NEMA Premium Efficiency motor supplied with NEMA MG-1 Part 31.4.4.2 insulation standards for inverter-fed polyphase motors. Selected options Casing Wear Ring - Not included Motor Nameplate Voltages (200, 416, 480, 600 volts) Couplings-Rotex Casing Wear Rings - Bronze (B584-936) Additional equipment Flotrex: FTV-10FA (570200-482) Suction Guide: SG-108 (516860-029) www.armstrongfluidtechnology.com 10/26/2016, Ref. # 503840.1 rev6 Page 6 of 20
Submittal Ref. #: 503840.1 rev6 Horizontal base mounted end suction pump Model: Series 4030-4x3x10-75 hp Pump (Motor supplier: Armstrong choice) Project name: 16-0058 - Philadelphia Airport - Concourse B Location: Representative: Blankin Equipment Corporation Date submitted: 10/20/2016 12:19:36 PM Phone number: Engineer: e-mail: blang@blankinequipment.com Contractor: Submitted by: Brandon Lang Application design data Tag number: P-3,4 Pipe orientation: Single Suction pressure: Location: Fluid: PropyleneGlycol:30 Quantity: 2 Operating temperature: 60 F Duty flow per pump: Duty head: Total dissolved solids: Materials of construction 695 USgpm 260 ft 0 ppm Viscosity: 0 ft 37.213 SSU Specific gravity: 1.0248 Construction: BF Impeller: Bronze (B584-844) Rating: ANSI-125 Pump shaft: Carbon Steel Connections: Inlet: 4 in, Outlet: 3 in Shaft sleeve: 304 SS Casing (volute): Cast Iron (A48-30) Flexible coupling: Rotex Bearings: Anti-Friction Grease Lubricated Casing gasket: Confined Non-Asbestos Fiber Mechanical seal data Seal type: Inside Single Spring Rotating face: Resin Bonded Carbon Manufacturer code: C-ssc L EPSS 2A Stationary seat: Sintered Silicon Carbide Springs: Stainless Steel Secondary seal: EPDM Rotating hardware: Motor electrical data Stainless Steel Supplier: Factory Choice Insulation class: Class F Insulation Size: 75 hp Inverter motor type: Inverter Duty Frame number: 365TSC Efficiency: NEMA Prem (12.12) Enclosure: TEFC Speed: 3580 rpm Motor Electrics: 208/3/60 Operating limits (temperature - pressure) Maximum pressure: 175 psi Maximum temperature: 250 F Pump casings are hydrostatically tested to 150% of maximum pump working pressure rating. www.armstrongfluidtechnology.com 10/26/2016, Ref. # 503840.1 rev6 Page 1 of 20
Performance curve Head (ft) 480 400 320 240 160 80 10.19 in39 8.73 in 8.00 in 53 63 System Series 4030 4x3x10 @ 3580 rpm 70 74 76 77 76 74 60 50 40 30 hp 0 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 70 75 63 125 100 PT75-1-0 (3.23.0.1) ANSI/HI 14.6.3.4 2B --- Admin Data --- Tag Num: P-3,4 Location: --- Motor Data --- Motor Size: 75 hp Motor Speed: 3600 rpm --- Design Duty Point --- Flow: 695 usgpm Head: 260 ft Impeller: 8.73 in --- Performance Data --- NPSHR: 18.3 ft Eff. @ Design: 76.44 % BHP @ Design: 61.17 hp Mtr Capability @ Rated Spd: 75.00 hp %Mtr Safety: 22.60% BEP @ Design Imp.: 76.57 % @ 667.0 usgpm Impeller Max BHP @ Flow: 72.32 hp @ 964.9 usgpm %max imp. range: 33.37 % Outlet Velocity: 30.16 ft/s VFD Setting: 60.0 Hz PropyleneGlycol:30, spgr= 1.0248 Flow ( 1,000 usgpm) Head (ft) 400 Series 4030 4x3x10 @ 8.73 in PT75-1-0 (3.23.0.1) ANSI/HI 14.6.3.4 2B --- Admin Data --- Tag Num: P-3,4 Location: 320 240 160 80 3580 rpm 3080 rpm 2580 rpm 2080 rpm 1580 rpm 53 63 70 System 20 hp 74 77 30 hp 25 hp 77 77 74 40 hp 50 hp 60 hp 75 hp 1074 rpm7.5 hp10 hp 15 hp 0 0 0.2 0.4 0.6 0.8 1 1.2 PropyleneGlycol:30, spgr= 1.0248 70 63 Flow ( 1,000 usgpm) --- Motor Data --- Motor Size: 75 hp Motor Speed: 3600 rpm --- Design Duty Point --- Flow: 695 usgpm Head: 260 ft Impeller: 8.73 in --- System Intersect Data --- 1. System @ 60.0 Hz: 695 @ 260, 61.17 hp 2. System @ 51.6 Hz: 598 @ 192.5, 38.97 hp 3. System @ 43.2 Hz: 500.9 @ 135, 22.9 hp 4. System @ 34.9 Hz: 403.8 @ 87.8, 12 hp 5. System @ 26.5 Hz: 306.8 @ 50.7, 5.26 hp 6. System @ 18.0 Hz: 208.5 @ 23.4, 1.65 hp www.armstrongfluidtechnology.com 10/26/2016, Ref. # 503840.1 rev6 Page 2 of 20
Dimensional data (not for construction) Side view Top view Weight: 1061 lb Not to scale Units of measure : inches [millimeters] Tolerance of ± 0.125 inch (± 3 mm) should be used For certified dimensions, please contact your Armstrong representative Pump equipped with casing drain plug and ¼ inch NPT suction and discharge gauge ports Connection details Connection Size Rating OD Bolt quantity* BCD Bolt size Inlet 4 ANSI-125 9 8 7.5 0.625 Outlet 3 ANSI-125 7.5 4 6 0.625 *Equally spaced straddling centreline Special instructions The program has defaulted to a NEMA Premium Efficiency motor supplied with NEMA MG-1 Part 31.4.4.2 insulation standards for inverter-fed polyphase motors. Selected options Casing Wear Ring - Not included Couplings-Rotex Additional equipment Flotrex: FTV-6FS (570200-380) Suction Guide: SG-64 (516860-023) www.armstrongfluidtechnology.com 10/26/2016, Ref. # 503840.1 rev6 Page 3 of 20