INERTER DC CC 150 Repeatable welds again, and again, and again 5 Year * Ultima 150 comes with: Ultima 150 unit Quick Change Torch** Torch spare parts kit Coolant Quick Specifications # Processes Plasma Arc Welding () Industrial Applications Automation Appliance Manufacturing Metal Furniture Manufacturing Electrical Manufacturing Aerospace/Aircraft Computer/Office Equipment Medical Services Fabrication Input oltage 208-460 AC Phase 575 AC 3 Phase w/optional module Rated Output 100A@18 100% Duty Cycle 150A@25 50% Duty Cycle Amperage Range 0.5 15 Amps 5 150 Amps Weight 130 lb (59 kg) Order Information See ordering information page for details. * Limited warranty. Refer to warranty schedule. **Refer to ordering information for torch selection. # Subject to change without notification. Quick Change Torch! No tools required. Cost Savings! The Ultima 150 is priced competitively with automated TIG systems. Plasma welding is measurably the lower cost process with savings gained through increased productivity, reduced scrap, reduced down time and fewer electrode changes. Wide Current Range! 0.5 150amp current range for quality performance over a wide variety of applications. ery Smooth Arc! Ultra smooth DC arc for repetitive, high quality welds. Repeatable Arc Starting! Pilot arc allows for repeatable arc starts, reducing defects and rework. Multiple oltage! 208-460 AC in 1 or 3 phase power at 50 or with 575 AC optional module. Simple to Set-Up! The Ultima 150 is a self contained unit, which requires attaching input power and gasses, then mounting the torch. Smart Logic! Prevents damage to the internal components if installed to improper voltage. Current Limiter! Limits power source output to torch capability to avoid torch damage. Preview Set Current! Allows you to display actual current/voltage and avoid costly test set-ups. Easy to Use! Simple interface for automated or manual control.
What is Plasma Welding? # INERTER DC CC 150 Plasma Welding is a superior variation of the TIG process that offers many advantages over TIG: Protected Electrode Used Tig Electrode Increases productivity by reducing down time Reduces scrap by providing consistent arc starting every time Improved process control for repeatable, high quality welds Reduces interference (noise) with computers, phone systems, CNC controllers Simply stated, plasma welding is a variation to GTAW (TIG) that encloses the tungsten electrode in a protected environment (Fig. 1) and delivers the arc through a cooled copper tip. Enclosing the electrode protects it from contamination, thus substantially extending electrode life. The consistent arc shape of plasma results in consistent welds for 8 hours or more of operation as compared to automated TIG welding, where deterioration of the exposed TIG electrode (Fig. 2) can result in weld arc variations (Fig. 3) in one hour or less of operation. Plasma welding uses a pilot arc (Fig. 4) to consistently transfer the arc to the work without the repeated use of high frequency current. The Ultima 150 pilot arc circuit results in repetitive starting and reduces problems of high frequency interference with CNC controls, phones and computers which are common with the TIG process. New Electrode Used Plasma Electrode Figure 1 Figure 2 Tig Weld Sample Pilot Figure 3 Figure 4 Typical Plasma/TIG Welding Productivity Benefit Analysis TIG PLASMA Total Parts Tig Electrode Minutes to Parts Lost Plasma Electrode Parts Lost Net Gain Plasma Time at 100% Cap. Changes Change Electrode with TIG Changes with Plasma over TIG Hour 208 1 5 17 0 0 17 Day 4,992 24 120 416 3 52 364 Week 24,960 120 600 2,080 15 260 1,820 Month 108,160 520 2,600 9,013 65 1,127 7,887 Year 1,297,920 6,240 31,200 108,160 780 13,520 94,640 Shift Hours per Day 24 Days worked per Week 5 alue Per Part: 1 Production Parts/Dollars Gained with Plasma: 94,640 Application: Outside corner welds home appliance Note: 4 welds required on each part. For more information, contact Thermal Arc or your Authorized Thermal Arc Distributor. # Subject to change without notification.
Features # INERTER DC CC 150 Easy fill coolant reservoir with built-in deionizer bag. Plasma & Secondary gas flow meter. System status and error indicator lights. Digital welding/pilot current amp meter. Quick disconnect hand held or automated torches available.
Specifications # INERTER DC CC 150 Ultima 150 Rated Output 150A/25 @ 50% @ Duty Cycle 208-460, Phase 100A/18 @ 100% 208-460, Phase 575 3 Phase w/optional module Output Ranges Low.5-15 A Load olts OC Input Hz Flow Meters Contractor Control Current Control Analog Control Shipping Weight High 5-150A 12-25 60 DC 50/ Plasma.5-3.0 SCFH (.25-1.5 lpm) Shield 5-30 SCFH (2.5-15 lpm) Remote Input Remote or Panel 0-10 olts DC Input 154 lbs/72 kg Input 208-575 olt Phase oltages 208 230 380 415 460 575 Power 1 ph 8 (KA) 3 ph 6 Current (Amps) 1 ph 37 34 3 ph 20 19 12 12 11 9 Dimensions & Weight Dimensions HxWxD 18 x 15 x 28.5 in (457 x 381 x 724 mm) Weight 130 lb (59 kg)
Control Panel # INERTER DC CC 150 3 4 5 6 7 8 9 10 11 2 1. Primary On/Off Circuit Breaker 2. Shield Gas Flow Control 3. Plasma Gas Flow Control 4. Pilot Arc On/Set 5. Pilot Current Adjust 6. Pilot Current Preview 7. Weld Current Preview/Actual 1 8. Weld Current Adjust 9. Current Limiter Adjust 10. Weld Current Range 11. Remote/Panel Control PANEL INDICATOR LIGHTS 1. AC - indicates correct input voltage is applied 2. TEMP - over temperature indicator light 1 2 3 4 5 6 3. Gas - lights to indicate Plasma & Shield gas pressure switches are satisfied 4. Coolant - indicates proper coolant flow to torch 5. Pilot - indicates pilot arc is active 6. DC - indicates output welding DC current is active
Torch Specifications # INERTER DC CC 150 2A Type PWH-2A 70 PWH-2A 90 PWM-2A 180 Offset Part No. 2-2100 (H) 2-2104 (H) 2-2101 (H) 2-2105 (H) 2-2102 (H) 2-2103 (M) 2-2106 (H) 2-2107 (M) Torch Lead Length Current Rating 75 Amps (DCSP) Torch Dimensions Coolant Requirements A B C D E 2,000 BTU/hr (504 K/Cal/hr) 1/4 gpm coolant flow 7-15/16" (202 mm) 7-3/4" (196 mm) 1-11/16" (43 mm) 1-11/16" (43 mm) 5/8" (16 mm) 5/8" (16 mm) 7/8" (22 mm) 7/8" (22 mm) @ 50 PSI (0.9 lpm @ 18-1/4" 13/16" Min. Max. 3.7 kg/cm 2 ) (463 mm) (21 mm) 7-1/8" 15" (181 mm) (381 mm) 3A PWH-3A 70 PWH-3A 90 PWM-3A 180 Offset 2-2110 (H) 2-2114 (H) 2-2111 (H) 2-2115 (H) 2-2112 (H) 2-2113 (M) 2-2116 (H) 2-2117 (M) 150 Amps (DCSP) 6,000 BTU/hr (1513 K/Cal/hr) gpm coolant flow @ 50 PSI (1.25 lpm @ 3.7 kg/cm 2 ) 8-3/4" (222 mm) 8-1/2" (216 mm) 19-1/4" (489 mm) 2-5/8" (67 mm) 2-5/8" (67 mm) 1" (25 mm) 7/8" (22 mm) 7/8" (22 mm) Min. Max. 9-1/4" 16-3/4" (235 mm) (425 mm) 1-1/16" (27 mm) 1-1/16" (27 mm) PWH-4A 70 2-2120 (H) 2-2125 (H) 12.5 ft 12-1/2" (318 mm) 3-3/16" (81 mm) 1-1/4" (32 mm) 4A PWH-4A 90 PWM-4A 180 Offset PWM-4A1 180 Inline 2-2119 (H) 2-2126 (H) 2-2121 (H) 2-2122 (M) 2-2127 (H) 2-2128 (M) 2-2123 (H) 2-2124 (M) 2-2129 (H) 2-2130 (M) 200 Amps (DCSP) 8,000 BTU/hr (2017 K/Cal/hr) 1/2 gpm coolant flow @ 50 PSI (1.9 lpm @ 3.7 kg/cm 2 ) 12-1/4" 311 mm) 18" (457 mm) 21" (.53 m) 3-3/16" (81 mm) 1-3/4' (44 mm) 1-3/4" (44 mm) 1-1/4" (32 mm) Min. Max. 8-1/4" 16" (209 mm) (406 mm) Min. Max. 11-1/4" 19" (286 mm) (483 mm) 1-1/4" (32 mm) 1-1/4" (32 mm) NOTE: All torches listed incorporate a quick disconnect connector specifically for operation with the Ultima 150. (H) designates torch with molded handle (M) designates torch with rack and pinion assembly
Torch Parts # INERTER DC CC 150 SPARE SPARE SPARE PARTS PARTS PARTS ITEM PART 2A KIT 3A KIT 4A KIT NO. DESCRIPTION TORCH 5-2984 TORCH 5-2985 TORCH 5-2986 1 Torch Head 8-2027 (70 ) 8-3030 (70 )) 8-4014 (70 ) Assembly 8-2028 (90 ) 8-3031 (90 ) 8-4015 (90 ) 8-2097 (180 offset) 8-3032 (180 offset) 8-4016 (180 offset) 8-4054 (180 inline) 2 Shield Cup 8-3236 (use w/ext. tip) 2 8-3040 1 8-4088 1 8-2071 (use w/std. tip) 3 Tip 8-2023 (.045) 35A-std 9-1788 (.031) 35A-lg 9-1890 (.062) 100A-lg 5 8-2024 (.062) 55A-std 9-1789 (.046) 50A-lg 5 9-1891 (.093) 125A-lg 5 8-2025 (.081) 75A-std 9-1790 (.062) 75A-lg 9-1892 (.125) 150A-lg* 5 8-2079 (.031) 15A-lg 9-1791 (.081) 100A-lg 5 8-2080 (.045) 25A-lg 9-1811 (.-093) 130A-lg 5 8-2082 (.062) 35A-lg 5 8-2083 (.081) 50A-lg 5 4 Electrode 8-2033 (.093) std 8-2007 (.093) std. 2 9-1827 (.187) std. 2 8-2006 (.093) ext. 9-1775 (.093) ext. 9-1834 (.187) ext. 8-2044 (.040) std. 8-2046 (.040) ext. 5 Liner N/A N/A 8-4011 2 6 Gas Distributor 8-2040 (.093-electrode) 1 9-2240 1 9-2204 1 (insulating sleeve) 8-2042 (.040-electrode) 7 Gas Diffuser N/A 8-3059 8-4087 8 Collet Assembly 8-2039 (.093-electrode) 9-1780 1 9-1876 8-2041 (.040-electrode) 9 Back Cap 8-2032 (std-electrode) 9-1779 (std-electrode) 8-4158 (std-electrode) 8-2030 (ext-electrode) 9-1803 (ext-electrode) 9-1877 (ext-electrode) N/S Collar N/A N/A 8-4024 N/S O-ring (liner) N/A N/A 8-0560 N/S O-ring (internal) N/A N/A 8-0528 N/S O-ring (back-cap) 8-2035 8-0527 8-0530 N/S Gasket (shield cup) 8-2036 8-3057 8-4069 N/S Gage/Wrench Assy 8-2021 1 9-1810 1 9-1873 1 N/S Lubricant 8-4025 1 8-4025 1 8-4025 1 N/S Tool Box 8-3141 1 8-3141 1 8-3141 1 NOTE: The use of extended electrode requires an extended back cap. Tip ratings @ minimum electrode setback. *Tip maximum current rating not to exceed the maximum output of Ultima-150
Ordering Information INERTER PRODUCT PART NO. DESCRIPTION QTY PRICE Ultima 150 3-2770 Power source only inc. quick disconnect assembly DC CC 150 Ultima 150 System Torch (rating) PART NO. PART NO. SYSTEM w/12.5ft torch & leads w/25ft torch & leads DESCRIPTION 2A (75 Amps) 1-1551-21 1-1552-21 PWH-2A, 70 degree 1-1551-22 1-1552-22 PWH-2A, 90 degree 1-1551-23 1-1552-23 PWH-2A, 180 degree 1-1553-23 1-1553-23 PWM-2A, 180 degree 3A (150 Amps) 1-1551-31 1-1552-31 PWH-3A, 70 degree 1-1551-32 1-1552-32 PWH-3A, 90 degree 1-1551-33 1-1552-33 PWH-3A, 180 degree 1-1553-33 1-1553-33 PWM-3A, 180 degree 4A (200 Amps) 1-1551-41 1-1552-41 PWH-4A, 70 degree 1-1551-42 1-1552-42 PWH-4A, 90 degree 1-1551-43 1-1552-43 PWH-4A, 180 degree 1-1551-53 1-1552-53 PWH-4A1, 180 degree 1-1553-43 1-1553-43 PWM-4A, 180 degree 1-1553-53 1-1553-53 PWM-4A1, 180 degree ACCESSORIES PART NO. DESCRIPTION Quick Disconnect Kit 5-2990 Allows existing torches to be converted for use with Ultima 150 Regulator - Argon 9-2722 Regulator - Argon/Hydrogen 9-3053 Foot Control 7-3080 Hand Pendant 10-2005 Requires 7-3316 adapter Remote Interface Cable 10ft. 9-4063 Weld Process Controller - WC-1 600279 Remote Hand Pendant 25ft. 600280 Cable Assembly (required for WC-1) 9-4129 TOTAL QUOTE PRICE NOTE: PWH designates a torch with a molded handle; PWM designates a torch with rack and pinion. Torch amperage rating based on minimum electrode set back.