ST Sliding-door-drive for sliding doors ST 9.5 ST 80. Output torque: 90-800 Nm Output speed: 5 - rpm Control panels for ST WS 905 / TS 00.0.0 Subject to alterations. (_Db).000
ST Sliding-door-drive For driving: Sliding-doors Series SG50R ST 9.5 ST 9. Series ST 6.5 ST 0. Series SG5R ST 60.5 ST 80. ST are special drives for sliding-doors designed for industrial use. ST comprises of: Worm gear with integrated friction clutch, interchangeable output-shaft, magnetic brake (optional), emergency manual operation (optional), integrated limit switch (optional), mounting accessories and electrical motor. Output side: The interchangeable output-shaft allows easy modification from left- to right-hand use. Friction clutch: The integrated friction clutch guarantees impact-damped, low-wear operation. Magnetic brake (optional): Ensures precise positioning of the door limit position, slightly heating ensures trouble-free operation at low outside temperatures. Integrated limit switch (optional): No need of separate limit switches SG50R Approvals and certificates Type test according to: DIN EN 5 DIN EN 605- DIN EN 605--0 SG5R Emergency manual operation (optional) E.g.: for top-hung sliding doors Hand crank NHK Hand chain operator KNH Limit switch integrated (optional) Mechanical limit NES operating, emergency- and auxiliary limit switches Digital limit DES Absolute encoder, after a power failure, re-adjustment is not required Separate limit switch (optional) Roller-arm limit switch Inductive limit switch Mounting Foot angle (standard fitting) Mounting base Special versions Increase of movements per hour Other voltages and frequencies ST-TRK: Sliding-door with magnetic brake ST-SI: Sliding-door with integrated safety brake, e.g. for sliding doors operating on an incline Door controls Simple connection to the limit switch by means of non-interchangeable plug connections allowing simple exchange with other GfA control panels Control voltage: V Frequency: 50 / 60 Hz Supply voltage: N~0V, ~0V, N~00V, ~00V Details of all GfA door controls for sliding doors can be found from page.0. Subject to alterations. (_Cf).0
. Technical data Series ST 9.5 SG50R ST 9. SG50R ST 6.5 ST 6. ST 0.5 Output torque Output speed Max. door weigth Door speed Output shaft / hollow shaft (Ø) Permitted OPEN / CLOSE output speed in frequency-inverter operating mode Motor power Supply voltage Operating frequency Operating current Max. movements per hour 5 Supply side wiring fusing (delayed-action) Limit switch range 6 Weight Spare parts: Catalogue page Part no. installation drawing (dxf, dwg) Part no. Nm rpm N cm/ sec mm rpm kw V - Hz Hz A kg 90 90 60 60 00 5 5 5 9.000 9.000 6.000 6.000 0.000 7 9 5 5 0 0 0 6 / 6 / 6 / 6 / 6 / 6 0,0 0,7 0,55 0,0 0,75 ~0 / 00V ~0 / 00V ~0 / 00V ~0 / 00V ~0 / 00V 50 50 50 50 50,6 /,5, /,, /,8, /,8 5, /,0 0 0 6 5x,5² / 0A 5x,5² / 0A 5x,5² / 0A 5x,5² / 0A 5x,5² / 0A 0 / 0 0 / 0 0 / 0 0 /0 0 /0 6 6 5 6 9.09 9.09 9.09 9.09 9.09 50000976 50000976 5000099 5000099 5000099 0007 00097 0007 00099 0007 Series ST 0. ST 60.5 SG5R ST 60. SG5R ST 80.5 SG5R ST 80. SG5R Output torque Output speed Max. door weigth Door speed Output shaft / hollow shaft (Ø) Permitted OPEN / CLOSE output speed in frequency-inverter operating mode Motor power Supply voltage Operating frequency Operating current Max. movements per hour 5 Supply side wiring fusing (delayed-action) Limit switch range 6 Weight Spare parts: Catalogue page Part no. installation drawing (dxf, dwg) Part no. Nm rpm N cm/ sec mm rpm kw V - Hz Hz A kg 00 600 600 800 800 5 5 0.000 60.000 60.000 80.000 80.000 9 9 9 0 50 50 50 50 / 6 / 6 / 6 / 6 / 0,85,0,50,0,00 ~0 / 00V ~0 / 00V ~0 / 00V ~0 / 00V ~0 / 00V 50 50 50 50 50, /,6 7, /, 6,7 /,9 7,0 /, 8, /,7 6 6 6 0 0 5x,5² / 0A 5x,5² / 0A 5x,5² / 0A 5x,5² / 0A 5x,5² / 0A 0 / 0 0 / 60 0 /60 0 / 60 0 / 60 6 50 50 5 5 9.09 -- -- -- -- 5000099 5000 5000 5000 5000 00099 0000 00059 0007 00095 Generally applies: Protection class IP5, permissible temperature range -0 C...+0 C (+60 C), from -0 C in combination with a permanently used magnetic brake, operating sound pressure level SPL 70 db(a) See.6 Door speed when operated with standard chain wheel, see 5. We recommend the selection of a special (enquire) for use with frequency inverter, OPEN drive speed at 87 Hz, see.6 and.7 The operating current in door drives can reach up to x the rated current for limited periods, see.7 and.8 5 When using a temperature range of +0 C...+60 C use half of maximum movements per hour, see also. 6 Maximum possible revolutions of output-shaft with integrated limit switch, see.9.0 Subject to alterations. (_Cf)
. Notes. European directive In accordance with the product standard EN - Doors- and EN 5 Safety in use of power operated doors-requirements.. Movements per hour The indicated movements per hour (See item -. Technical data) may not be exeeded.. Magnetic brake The optional magnetic brake locks the output-shaft when the motor is switched off. The magnetic brake ensures precise positioning of the door in the limit position and avoids overrunning the limit position of the door. Slight heating ensures trouble-free operation at low outside temperatures.. Gear self-braking / Brake Drives without an electric brake have a self-sustaining worm gear and stop automatically. On drives with an electric brake, stopping is achieved by the external brake. Brake inspection must always be carried out by qualified service engineers..5 Manual operation In the event of power failure, the door can be opened by hand after releasing the friction clutch. Emergency manual operation by crank handle or chain is also available as an option (e.g. for top-hung sliding doors)..6 Output torque / Door weight / Friction clutch.7 Motor overload protection Motor overload protection must be able to withstand x the operating motor current because the starting current of the drive unit can reach these levels for short periods..8 Use with external frequency inverter For external frequency inverters applies: A higher than recommended drive speed puts extra load onto the gear. This extra load must be taken into account when sizing a drive by reducing the available output torque.. The admissible drive speeds may not be exceeded (See item -. Technical data). The operating forces must comply with EN 5, and the corresponding EMC directives must likewise be observed. If selecting a frequency inverter, note that the starting current of the drive unit can reach x of the operating motor current..9 Integrated limit switch The door construction should be designed to prevent the disengaging of drive elements (sprocket, chain, rack etc.). The stopping accuracy of the ST with magnetic brake and a limit switch range of E0 is approximately +/- 5mm (for E0, approx. +/- 5mm). The door construction must be designed to compensate onsite these differences (e.g. height- of the rubber profile of the safety edge). For higher requirements regarding stopping accuracy, we recommend the use of separate limit switches (roller-arm limit switches, inductive limit switches, etc.). The integrated slipping clutch guarantees impact-damped, lowwear operation. The admissible output torque is pre-adjusted. If the clutch is subject to higher forces than the admissible (e.g. the possibility of attempted forced entry) additional improvements of the door design may be required to prevent undesired opening of the door. The weights indicated apply to horizontal, rail-mounted sliding doors.. Dimensions. ST 9.5 ST 9. SG50R 7 5 8 Worm gear with friction clutch Motor Terminal box / optional: integrated limit switch Magnetic brake 5 Hand wheel for slipping clutch adjustment 6 Output-shaft right (optional: left) 7 Optional: WS 905 control panel 8 Cover 6 Permitted installation: horizontal (as shown) or vertical (motor to the top) Subject to alterations. (_Cf).0
. ST 6.5 ST 0. 7 8 5 6 Worm gear with friction clutch Motor Terminal box / optional: integrated limit switch Magnetic brake 5 Hand wheel for friction clutch adjustment 6 Output-shaft right (optional: left) 7 Optional: WS 905 control panel 8 Cover ST 6.5 ST 6. ST 0.5 ST 0. L 57 9 80 Permitted installation: horizontal (as shown) or vertical (motor to the top). ST 60.5 ST 80. SG5R 7 8 6 5 Worm gear with friction clutch Motor Terminal box / optional: integrated limit switch Magnetic brake 5 Friction clutch adjustment (SW 7) 6 Output-shaft right (optional: left) 7 Optional: WS 905 control panel 8 Cover ST 60.5 ST 60. ST 80.5 ST 80. L 57 56 59 57 Permitted installation: horizontal (as shown) or vertical (motor to the top). Emergency manual operation optional Hand crank operation NHK Rapid hand chain operator SK ( SG50) Hand chain operator KNH ( SG85 / SG5) Read note in.5.0 Subject to alterations. (_Cf) For Series Part no. L H SG50 SG85 SG5 00059 00079 000 55 5 65 9 9
5. Attachments / Accessories 5. Mounting base ST 9.5 ST 0. 5. Housing ST 9.5 ST 0. ST 6.5 0. ST 9.5 / 9. Part no. 000 Right- or left-hand use Housing Part no. 0005 Right- or left-hand use Locking cpl. for housing Part no. 00066 units 5. Sprockets / chain Chain (p x b) Description Part no. B- (/ x 7/6 ) 6 B- ( x 7,0mm),0m 5,0m Link,5m 5,0m Link 00000 00909 000065 000509 0090 000067 Sprockets for Designation Teeth s Part no. D K D 0 D n D i B H ST 9.5 / ST 9. ST 6.5 ST 0. ST 60.5 ST 80. B- (/ x 7/6 ) 0000,9 90 5, 0 6 B- ( x 7,0mm) 9 0000 65 5, 00 0 6, 5 6 B- ( x 7,0mm) 9 0000 65 5, 00 50 6, 5 5. C-profile For For Chain Part no. A B C S ST 9.5 / ST 9. ST 6.5 ST 80. B- (/ x 7/6 ) 007 9,5 6 B- ( x 7,0mm) 008 8 9 0,5 5.5 Chain-tensioner For For Chain Part no. L ST 9.5 / ST 9. ST 6.5 ST 80. B- (/ x 7/6 ) 0000 00 6 B- ( x 7,0mm) 00065 50 Subject to alterations. (_Cf).05
Door controls for ST WS 905 TS 00 WS 905 Reversing contactor control WS 905 Technical data Suitable for ST with NES mechanical limit switch Supply voltage: N~0V, PE ~0V, PE N~00V, PE Control voltage: V AC reversing contactors Permissible temperature range: -0...+50 C Housing Dimensions W x H x D [mm]: 5 x 0 x 09 Protection class: IP5 Design Mechanically locked reversing contactors Positioning button CLOSE / OPEN Plug-in connection cable to for configuration with integrated mechanical limit switch NES Available with optional readywired CEE plug, regarded as mains circuit breaker under the terms of EN 5. Functions Operating mode: Hold to run CLOSE / OPEN via an external control device TS 00 TS 00 Automatic door control Technical data Suitable for ST with DES digital limit switch or NES mechanical limit switch Supply voltage: N~0V, PE / ~0V, PE / N~00V, PE Control voltage: V DC Mains supply ratings for external devices: V DC (0.5A) / 0V AC (A) integrated reversing contactors (up to kw motor power) Display for programming ( lines with 0 signs) Permissible temperature range: -0...+50 C Housing Synthetic housing with transparent cover, Dimensions W x H x D [mm]: 0 x 00 x 85 Protection class: IP55 Design Plugged terminals with screw connections Pluggable cable sets to the with DES or NES Integrated push buttons for the adjustment of the door positions in use with DES Connectors for control devices ( for the door area, for gatekeeper operation) Functions Automatic detection of DES or NES limit switches Intermediate open position for passengers (for use with NES is an additional limit switch required) Convinient adjustment via selector switch and display status Adjustment of the door final positions and intermediate positions from the operator level (DES) Self-hold in both directions, in case of failure - automatic switching to Hold to run mode Safety edge system 8k, evaluation for 6 safety edges Connection plugs for control devices with next function (pull switch or external radio receiver) Integrated timer with week program, OFF via external switch Automatical run-time monitoring (real runtime + 8%) Automatic closing feature adjustable (-999 sekc.), adjustable in steps of seconds Possibility of adjustable clearance time (-99 Sek.) Separated adjustment of the automatic closing function for complete- or partially opening Adjustable function of the traffic lights in the final door positions or the clearance time Adjustable reaction of the photo cell in the final limit position OPEN Fault memory Cycle counter (non-resettable) and maintenance cycle counter Modul with Relays for the final door positions and faults (potential free) Subject to alterations. (_Dc).0
Connection options TS 00 Slot for inductive signal transmission (ASO) Slot for -channel radio 6 safety edges 8 K x x x V / 0.5 A External Potential-free signal contacts Slot for loop detector N~0 V, PE ~0 V, PE N~00 V, PE 0 V /.0 A External Door controls and accessories Designation Description Part no. WS 905 - Reversing contactors V For drives without limit switch; with 0.8m cable and connection plugs for, without CEE-plug 0090500.0000 WS 905 - Reversing contactors V For drives with limit switch; with 0.8m cable and connection plugs for, without CEE-plug 0090500.000 TS 00 ST-door control for DES/NES 000000.0000 5 DES connection cable for TS 00 NES connection cable for TS 00 Inductive signal transmission (ASO) 5 Connection to drives with digital limit switch, pluggable on both sides; length of cable:.0m Connection to drives with mechanical limit switch, pluggable on both sides; length of cable:.0m Modul for TS 00 for monitoring of inductive signals from safety edges (brand ASO) 0000.0000 00087.0000 000 7 6 Radio receiver -channel Loop detector -channel 6 7 Modul for TS 00 (for Opening and Intermediate opening) Modul for TS 00 (for OPEN- and CLOSE signal) 008 0065.0 Subject to alterations. (_Dc)