Data sheet Item no.: 100 Page: 1 / 5 Operating data Requested flow rate 178.00 US GPM Requested developed head 14.40 ft Pumped medium Water Clean water Not containing chemical and mechanical substances which affect the materials Ambient air temperature 68.0 F Fluid temperature 68.0 F Fluid density 62.303144 lb/ft³ Actual flow rate 178.10 US GPM Actual developed head 14.42 ft Efficiency 37.1 % Power absorbed 1.75 HP Pump speed of rotation 1752 rpm Shutoff head 22.00 ft Single system 1 x 100 % Performance test No Fluid viscosity Max. power on curve Orientation Suction flange pump drilled according to(dn1) Discharge flange pump drilled according to(dn2) Shaft seal Manufacturer Type 0.0015 in²/s 2.10 HP Close-coupled submersible Vertical unmachined EN 1092-2 / DN 80 / PN 10 2 mech. seals in tandem arrangement with oil reservoir KSB MG Tolerances to ISO 9906 Class 3B; below 10 kw acc. to paragraph 4.4.2 Material code SIC/SIC/NBR Impeller type Free flow (vortex) impeller (Fmax) Impeller diameter 5.51 in Free passage size 2.99 in Direction of rotation from drive Clockwise Ex protection Explosion protection to NEC Class1, Div 1, Gr.C, D T3 Color Ultramarine blue (RAL 5002) KSB-blue Driver, accessories Driver type Electric motor Model (make) KSB Motor const. type KSB Sub. motor NEMA code letter K Efficiency class Efficiency class IE3 acc. to IEC60034-30-1 Frequency 60 Hz Rated voltage 230 V Rated power P2 2.00 HP Available reserve 14.49 % Rated current 5.5 A Starting current ratio 7.9 Insulation class H according IEC 34-1 Type of protection XP/I/1/CD Motor enclosure IP68 Cos phi at 4/4 load 0.79 Motor efficiency at 4/4 load 86.5 % Motor service factor 1.15 Temperature classes T3 aggregate Temperature sensor Bimetal switch 2x Motor winding 230 V Number of poles 4 Starting mode Direct-on-line starting Connection mode Star Motor cooling method Surface cooling Motor version X Cable design Rubber hose Cable entry Sealed along entire length Power cable AWG 15-8 Number of power cables 1 Moisture sensor With Cable length 49.21 ft
Data sheet Item no.: 100 Page: 2 / 5 Materials G Notes General criteria for a water analysis: ph-value >= 7; chloride content (Cl) <=250 mg/kg. Chlorine (Cl2) <=0.6 mg/kg. Pump casing (101) Discharge cover (163) Shaft (210) Chrome steel ASTM A276 Type 420 T Impeller (230) Bearing bracket (330) O-Ring (412) Motor housing (811) Motor cable (824) Screw (900) Nitrile rubber NBR Chloroprene rubber Stainless steel A 193 B8M Packaging Packaging category Packaging for transport IPPC Standard ISPM 15 B1 Wooden or plywood case, cover provided with polyproylene cellular sheet, outdoor storage up to 3 months Ship Yes Packaging for storage Indoor Outdoor storage at -40 C to +50 C for up to 3 months. Packet must be covered. No corrosion protection, only transport protection. Nameplates Nameplates language International Duplicate nameplate With Installation parts Installation type Scope of supply Installation depth Material concept stationary 2 guide rail Pump with installation parts For guide rail arrangements, the guide rails are not included in KSB's scope of supply. 14.76 ft G Type Chain Material CrNiMo steel 1.4404 Length 16.40 ft Max. load 441 lbm Lifting Bail With Duckfoot bend Size DN 80 Flange design Duckfoot bend size (DN2 / DN3) DN 80 Drilled according to Material Grey cast iron EN-GJL-250 Mounting type Composite anchor bolts Foundation rail Without Claw straight Size DN 80 Lifting chain / -rope
Performance curve Page: 3 / 5 60 Total developed head 40 [ft] 20 ø210.0 ø140.0 ø130.0 0 10 NPSH req. [ft] 8 6 40 [%] Efficiency 20 0 2.0 Power Input [HP] 1.5 Flow Curve data Speed of rotation Fluid density Viscosity Flow rate Requested flow rate Total developed head Requested developed head 1752 rpm 62.303144 lb/ft³ 0.0015 in²/s 178.10 US GPM 178.00 US GPM 14.42 ft 14.40 ft Efficiency 37.1 % Power absorbed 1.75 HP NPSH req. 3% 6.63 ft Curve number K43337 Effective impeller diameter 5.51 in Acceptance standard Tolerances to ISO 9906 Class 3B; below 10 kw acc. to paragraph 4.4.2
Installation plan Page: 4 / 5 3.39 ø2.36 24.72 20.63 1.97 18.35 ø0.47 3.23 27.01 5.98 1) 23.94 DN3 min18.86 14.96 DN1 7.87 1) Minimum water level t1 3.74 4.92 28.43 ø0.71 5.51 8.66 11.89 6.42 min14.17 5.91 Access opening min 25.59 Drawing is not to scale Dimensions in in
Installation plan Page: 5 / 5 Motor Motor manufacturer KSB Motor size 2E Motor power 2.00 HP Number of poles 4 Speed of rotation 1746 rpm Motor enclosure IP68 Connections Suction flange pump drilled according to(dn1) Duckfoot bend size (DN2 / DN3) unmachined DN 80 Drilled according to Weight net Pump, Motor, Cable Claw / Foot Total Connect pipes without stress or strain! Dimensional tolerances for shaft axis height: DIN 747 Dimensions without tolerances, middle tolerances to: ISO 2768-m Connection dimensions for pumps: EN735 Dimensions without tolerances - welded parts: ISO 13920-B Dimensions without tolerances - gray cast iron parts: ISO 8062-CT9 208 lbm 21 lbm 229 lbm For auxiliary connections see separate drawing.