Installation JETTA manual: Parrot MKi + Parrot CK3100 range JETTA This The VOLKSWAGEN sheet is designed JETTA to marque help you and with VOLKSWAGEN the installation logo are of a the Parrot property product of the and VOLKSWAGEN is purely for France information. Group s.a Any or VOLKSWAGEN installation performed AG. in compliance This document with is the only instructions valid for the appearing vehicle model in this JETTA document year 2011, is done excluding under the all sole other responsibility models in the of same the installer, range and who excluding is entirely later responsible for modifications the quality made of the to installation. the vehicle All by rights the manufacturer. reserved Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without the authorisation The Parrot brand of Parrot name SA. and Pictures logos are for the information exclusive property only. of Parrot SA.
Fitting time / Main features Disassembly 30min NO +IGN Mounting kit 30min NO ISO Reassembly 30min YES UNIKA Testing 15min FRONT LOUDSPEAKER TEL mode Total 1h45min ALL MUSIC mode CK range Tools -TORX screwdriver Plastic trim removal tools - Cutting pliers FACOM / BOJO - Crimping pliers - Multimeter or Test lamp - Wire tie - Electrical tape - 1.5 mm flat terminal and round male terminal MKi range Accessories required Kram ref. Dealer ref. CK range 86 200 YY 138 CABL 2 MKi range 84 942 YY 138 CABL 2 Photos for illustration purposes Updating "Please contact your wholesaler to purchase accessories. A list of wholesalers is available at www.certified.parrot.com. " To get the most out of your hands-free kit we recommend that you update your software regularly. The update procedure can be found at http://www.parrot.com/usa/support/downloads
Disassembly
Disassembly 1 / 2 1 1 2 2 Release the panel by inserting the plastic trim tools underneath. Remove screws 1 and 2. 3 4 Unclip the cabin light and Using the plastic trim tools, disconnect it. unclip the vanity light from the left-hand side. 5 6 3 5 4 6 Using the plastic trim tools, unclip the car stereo and air conditioning surround. Unplug the airbag indicator connector. Remove screws 3, 4, 5 and 6 around the car stereo. Disconnect the connector and the aerial cables.
7 7 10 Disassembly 2 / 2 8 9 8 9 Remove screws 7, 8, 9 and 10 around the air conditioning control unit, then remove it without disconnecting it. Unclip the fusebox cover from the bottom. 10 11 Using the plastic trim tools, unclip the side panel of the dashboard on the driver's side. Unclip the cover plate running up the side of the driver's door. 12 Remove the driver's side door seal.
Finding an ACC wire 1 2 Using a guide, feed an electric wire from under the steering wheel to the air conditioning control housing. Feed the wire to the left into the fusebox housing. Fit a 1.5 mm terminal and insert it into one of the small fuse slots on the side of the box (using a multimeter, check that the +12V supply is indeed controlled by the ignition key). 3 Connect the +IGN using a male round terminal to the blue wire of the 84942 adapter in front of the fuse holder or on the red wire of the 86200 or YY138CABL2 adapter.
Wiring the microphone 1 / 2 1 2 3 Using a guide, feed the cable from the windscreen to the cabin light. Glue the bracket (supplied) in the centre of the cover which connects the rain sensor after degreasing. 4 Using a guide, feed the cable Using a guide, feed the cable from the cabin light to the from the courtesy light to the courtesy light. driver's side door. 5 6 Slide the cable along the driver's door pillar while replacing the door seal. Feed the cable from the driver's side of the dashboard.
Wiring the microphone 2 / 2 7 Using a guide, feed the cable under the steering wheel towards the air conditioning unit control housing.
Feeding the accessory cable 1 2 Using a guide, feed the cable in the top part of the glove compartment through to the air conditioning control unit housing. Make sure that the cable is long enough.
Fitting the hands-free system 1 / 2 1 Connect the adaptor to the original connector and connect all of the wires to the blue box as shown in the diagram below. Test the assembly before completing fitting and then slide everything behind the air conditioning control unit. Direct adaptor cable
Fitting the hands-free system 2 / 2 2 3! Slide the cable into one of the recesses in the radio frame. ATTENTION: When reassembling take great care not to cut the wire with the radio fixings. 3 After degreasing the right-hand side of the speedo surround, affix the mounting supplied. 12
Testing Before refitting the system, switch the kit on using the ignition (or by starting the car). By pushing the central knob of the remote control, check: 1 - that the menu is displayed on the screen (language or ipod etc). 2 - that the radio system is muted when the kit is in use (click in the blue box). 3 - that the sound through all speakers is properly muted. 4 - that there is sound through the front speakers for spoken menus. 5 - then turn off the ignition, verify that the kit turns off and that the message goodbye is displayed on the screen (otherwise reverse the fuses on the kit power supply harness). 6 - pair a telephone with the kit and make a call (check that both the microphone and the kit are working).
Reassembly Refit the system using the following procedure: 1 - refit the panel next to the dashboard 2 - refit the panel on the left-hand side of the dashboard 3 - replace the fusebox cover 4 - reconnect and refit the cabin light (screws 1 and 2) 5 - refit the cabin light panel 6 - refit the courtesy light 7 - refit the 4 screws (7, 8, 9 and 10) for the air conditioning control unit 8 reconnect the adaptor and the aerials behind the car stereo and slip them inside the housing (make sure that you do not trap and cut any screen wires) 9 - refit the 4 screws (3, 4, 5 and 6) for the car stereo 10 - refit the radio and air conditioning surrounds 11 - retest to check that the system is working correctly