Step 3: Identify and mark all energy control points

Developed by Reviewed by Revised by LOCKOUT BRADY BRADY TAGOUT PROCEDURE Description: Boiler 1 Equipment # B-1 Location: Westbrook Campus Bldg:Ginn Revn: 0 Date: N/A Origin Date: 5/05/09 Model# CB-900-70 Serial# L-100932 Asset # 19707 DANGER LOCKS & TAGS Steam pressure and burn hazard. Ensure steam and heat have dissipated NEEDED before proceeding. NEXT AUDIT DUE NEXT AUDIT DUE NEXT AUDIT DUE NEXT AUDIT DUE MAY 2010 MAY 2011 MAY2012 MAY 2013 Panels on North wall South Side of West Boiler along Floor W-1 E-1 G-1 G-2 ALWAYS PERFORM A MACHINE STOP BEFORE LOCKING OUT DISCONNECTS ID Source Location Method Check Device Disconnect for Circ. Move E-1 disconnect Verify ZERO Lock and Hasp E-1 Electrical Pump in Panel PP1 Breaker 9 to off. voltage 208V on East Wall Lock out. reading with meter. Gas Ball Valve Located on Turn G-1 valve off. Lock Verify Ball Valve G-1 Natural Gas South Side of Unit out. pressure has Main Near West End. bled off. Ball Valve Located on Turn G-2 valve off. Tag Verify Tag Gas South Side behind out. pressure has G-2 Natural Gas Main Gas Line. bled off. Pilot Globe Valve Located Turn W-1 valve off. Lock Verify Gate Valve Makeup Feed on South Side behind out. pressure has W-1 Water Main Gas Line. bled off. CP = CONTROL PANEL E = ELECTRICAL W = WATER P = PNUEMATIC C = CHEMICAL V = VALVE G = GAS S = STEAM OPENING A GUARD DOES NOT CONSTITUTE A LOCKOUT! Any machine modifications must be shown in procedure. Contact facilities to update procedure. Safety Is Your Responsibility! 800-496-4040 Page 1 of 2 Why? (LOTO) is an important safety procedure - critical to safeguarding workers and employees around the machinery and equipment they operate, service and maintain. It is also a major OSHA-inspection focus. In fact, it remains one of the most cited violations for general industry even after 20 years in force. But, rather than focusing on the negative aspects of non-compliance and citations, focus instead on the benefits a thoroughlydeveloped LOTO program provides: LIVES SAVED preventing an estimated 250,000 incidents, 50,000 injuries and 120 fatalities annually! CUT COSTS both in lost employee time and insurance costs IMPROVED PRODUCTIVITY minimizing equipment downtime BEST PRACTICE - being widely adopted across industries and industrialized countries 5 Steps To An Effective Program A successful (LOTO) program starts with a solid foundation and a written plan. After that, proactive training and employee awareness programs will ensure a safer workplace for everyone. Brady has broken down the process for OSHA compliance into five easy steps, each with their own effective elements that add up to total workplace safety. 8 Step 1: Develop and document your equipment energy control policy/program Step 2: Create and post written, visual equipment-specific lockout procedures Step 3: Identify and mark all energy control points Step 4: Train your employees, communicate and conduct periodic inspections Step 5: Equip your employees with the proper lockout tools and warning devices Learn More: Download the 5 Steps To An Effective Program Whitepaper Download the full whitepaper today for more information and details on each of these five steps. Visit BradyID.com/5steps to download the whitepaper. 438

OSHA Regulations OSHA s Volume 29 Code of Federal Regulation (CFR) 1910.147 standard addresses the control of hazardous energy when servicing or maintaining equipment. (1) Scope. (i) This standard covers the servicing and maintenance of machines and equipment in which the unexpected energization or start up of the machines or equipment, or release of stored energy could cause injury to employees. This standard establishes minimum performance requirements for the control of such hazardous energy. (2) Application. (i) This standard applies to the control of energy during servicing and / or maintenance of machines and equipment. (3) Purpose. (i) This section requires employers to establish a program and utilize procedures for affixing appropriate lockout devices or tagout devices to energy isolating devices, and to otherwise disable machines or equipment to prevent unexpected energization, start-up or release of stored energy in order to prevent injury to employees. 1910.147(c) OSHA Energy Control Policy; Synopsis of Requirements An energy control policy must be documented and at a minimum should cover the following aspects of the program: Purpose and scope of the program Shift transfer procedures Personnel authorized to perform LOTO Lock removal procedures Enforcement policy Method for auditing & updating procedures Training methods Coordination with outside contractors Group lockout procedures 1910.147(c)(4) Energy Control Procedures; Synopsis of Requirements Procedures must be documented and must identify the equipment covered. A separate procedure must be created for each piece of equipment to be locked out. There are exceptions where multiple machines may be grouped under a single procedure. The procedure must include specific steps for shutting down, isolating, blocking and securing equipment to control hazardous energy. Specific steps for the placement, removal and transfer of devices should also be included. The employer shall conduct and certify periodic inspections at least annually. 1910.147(c)(5) OSHA Device Requirements devices must: Be provided by the employer. Be standardized by size, shape or color. Be distinguishable from locks used for other purposes. locks should only be used for lockout! Identify the individual who applied the lock (both tags and lock labels are acceptable for this purpose). Be durable. Be strong enough to prevent removal except by using excessive force. Remain under the exclusive control of the individual who attached them. 1910.147(c)(5)(ii)(B) Standardized and tagout devices shall be standardized within the facility in at least one of the following criteria: Color; shape; or size; and additionally, in the case of tagout devices, print and format shall be standardized. 1910.147(c)(5)(ii)(A) Durable and tagout devices shall be capable of withstanding the environment to which they are exposed for the maximum period of time that exposure is expected. 1-800-661-9983 439

Standard Combination Kits Standard Combination Kits These combination lockout kits can be purchased with or without padlocks and tags. Padlocks included in these kits are keyed differently (each lock has its own unique key). See the Personal Kits section for kits with keyed alike padlocks. Combination Satchel Everything you need to lock out the most common mechanical and electrical control points, with extra valve lockout devices 1 - Large Univ. Valve w/ Blocking Arm (50899 and 65403) 1 - All Purpose Cable w/ 8 Sheathed Cable (50943) 1-1/4 to 1 Ball Valve (65666) 1-1 to 2-1/2 Gate Valve (65560) 1-2-1/2 to 5 Gate Valve (65561) 1-5 to 6-1/2 Gate Valve (65562) 1-120V Snap-On Breaker (65387) 1-120/277V Clamp-On Breaker w/ Cleat (65396) 1-480/600V Clamp-On Breaker w/ Cleat (65397) 1 - Universal Multi-Pole Breaker (66321) 1-110V Electrical Plug (65674) 1 - Wall Switch (65392) 1 - Satchel (51173) Optional: 2 - Keyed-different safety padlocks (99552) or steel padlocks (99500) 2 - Heavy duty, re-usable lockout tags (65520) and nylon cable ties 99686 Combination Satchel Kit 99687 Kit w/2 Safety Padlocks & 2 Tags 99688 Kit w/2 Steel Padlocks & 2 Tags Combination Toolbox Contains all of the basic tools needed to lock out gate and ball valves, circuit breakers, switches and plugs 1-1 to 6-1/2 Adjustable Gate Valve (64057) 1-1/4 to 1 Ball Valve (65666) 1-1-1/4 to 3 Ball Valve (65669) 1-120V Snap-On Breaker (65387) 1-120/277V Clamp-On Breaker w/ cleat (65396) 1-480/600V Clamp-On Breaker w/ cleat (65397) 1 - Universal Multi-Pole Breaker (66321) 1-110V Electrical Plug (65674) 1 - Wall Switch s (65392) 1 - Belt Pouch (51172) 1 - Extra-Large Toolbox (LKP-TKLBOX) Optional: 2 - Keyed-different safety padlocks (99552) or steel padlocks (99500) 2 - Heavy duty, re-usable lockout tags (65520) and nylon cable ties 99682 Combination Toolbox Kit 99684 Kit w/2 Safety Padlocks & 2 Tags 99685 Kit w/2 Steel Padlocks & 2 Tags Brady Maintenance Kit kit specifically designed for use by internal maintenance crews 1-1/2 to 2-1/2 Small Ball Valve (BS07A) 1-1 to 2.5 Gate Valve (65560) 1-2.5 to 5 Gate Valve (65561) 1 - All Purpose Cable (50943) 1-3-in-1 Electrical Plug (PLO23) 1 - Wall Switch (65392) 2-120/277V Clamp-On Breaker s w/ Cleats (65396) 2 - Universal Multi-Pole Breaker s (66321) 1-110V Electrical Plug (65674) 1 - AC Sensor (65269) 10 - Danger Tags (LT10) 1-1 Steel Hasp (T218) 1-1-1/2 Steel Hasp (T220) 3-3/4 Brady Key-Retaining Steel Padlocks, Blue, Keyed Different (143130) 1 - Sheet of Lock Labels (LID-2) 1 - Safety Training Booklet (2112X) 1 - Plastic Utility Box (LKP-TKLBOX) 134032 Brady Maintenance Kit View individual devices: Padlocks... page 464 Mini Cable... page 475 Cable... page 475 Ball Valve s... page 477 Gate Valve s... page 477 Plug Valve... page 477 Breaker s... page 483 Fuse s... page 486 440

Standard Combination Kits Prinzing Premium Kit Premium portable lockout kit that contains a large variety of electrical and mechanical lockout devices, tags, and labels 2 - Breaker s, Multi-pole (BL07) 3 - Breaker s, Single pole (BL01) 1-1 to 2.5 Gate Valve (65560) 1-2.5 to 5 Gate Valve (65561) 1 - Cable Device (CABLO) 1 - Wall Switch (WSLO) 1-3-in-1 Electrical Plug (PLO23) 1-120-600 AC Voltage Sensor (ESAC600) 3-1-1/2 Steel Hasps (T220) 5 - Labels Lock Out Before Servicing (LOSV15) 5 - Labels Lock Out Here (LOSV14) 5 - Labels Caution This Machine Must Be Locked Out (LOSV2) 20 - Tags (LT10) 14 - Padlock Labels (LID-2) 3 - Key-Retaining Steel Padlocks, 3/4 Shackle, Blue, Keyed Different (143130) 1 - Safety Training Booklet (2112X) 1 - Extra-Large Toolbox (LKP-TKLBOX) LKP Description Prinzing Premium Kit Prinzing Ultimate Kit Ultimate portable lockout kit contains a variety of lockout devices for electrical and mechanical applications 1 - Safetee Donut 1 to 2-1/2 (SD02) 1 - Safetee Donut 5 to 6-1/2 (SD06) 1 - Ball Valve (BS07A) 1 - Ball Valve (BS08A) 1 - Electrical Plug / Pneumatic (PL027E) 1 - Cable Device (CABLO) 2 - No-hole Breaker (BL04) 2 - Breaker, Triple-pole (BL03) 1 - Breaker, Multi-pole (BL07) 2-1-1/2 Steel Hasp (T220) 1 - Wall Switch (WSLO) 10 - Danger Do Not Operate Tags (LT10) 1 - Safety Training Booklet (2112X) 1-120-600 AC Voltage Sensor (ESAC600) 3 - Prinzing Padlocks 3/4 Blue (LC041-BU) 1 - Bag Duffel Style (LX980E) LK981E LK980E Description Ultimate Kit Bag Only Combination Duffel Everything you need to lock out the most common mechanical and electrical control points, with extra electrical lockout devices 1 - Mini Cable (50940) 1-120V Snap-On Breaker (65387) 1-120/277V Clamp-On Breaker (65396) 1-480/600V Clamp-On Breaker (65397) 1 - Universal Multi-Pole Breaker (66321) 1 - Oversized Breaker (65329) 1-3-in-1 Electrical Plug (PLO23) 1 - Wall Switch (65392) 1 - Plug Valve for stem dia up to 7/8 (113231) 1 - Plug Valve for stem dia 29/32 to 1-3/8 (113232) 1-1 to 6-1/2 Adjustable Gate Valve (64057) 1-1 to 2-1/2 Gate Valve (65560) 1-1/4 to 1 Ball Valve (65666) 1 - Large Univ. Valve w/ Blocking Arm (50899 and 65403) 1 - Belt Pouch (51172) 1 - Duffel Bag (99162) Optional: 2 - Keyed-different safety padlocks (99552) or steel padlocks (99500) 2 - Heavy duty, re-usable lockout tags (65520) and nylon cable ties 99689 Combination Duffel Kit 99690 Kit w/2 Safety Padlocks & 2 Tags 99691 Kit w/2 Steel Padlocks & 2 Tags Kit - Spanish Everything you need to lockout electrical and mechanical isolation points. All contents come with Spanish legends. 2-1-1/4 to 3 Steel Ball Valve (65669) 2-1/4 to 1 Nylon Ball Valve (65666) 2-1 to 2.5 Gate Valve s (65560) 2-2.5 to 5 Gate Valve s (65561) 1-110V Electrical Plug (65674) 1-220/550V Electrical Plug (65675) 6 - Wall Switch s (65392) 6-120V Snap-On Breaker (65387) 6-120/277V Clamp-On Breaker s (65396) 65043 Kit - Spanish 6 - Universal Multi-Pole Breaker s (66321) 5 - Aluminum Spanish Labeled Hasp 25 - Spanish Danger Tags w/ Cable Ties 6 - Brady Steel Padlocks, 3/4 Shackle, Blue, Keyed Different (99504) 6 - Brady Steel Padlocks, 2 Shackle, Blue, Keyed Different (99528) 2 - Canvas Security Bags (65780) 1-800-661-9983 441

Standard Electrical Kits Standard Electrical Kits Standard electrical lockout kits can be purchased with or without padlocks and tags. The padlocks included in these kits are keyed differently (each lock has its own unique key). See the Personal Kits section for kits with keyed alike padlocks. Portable Padlock Pouch Portable kit includes selection of padlocks, tags and hasps 2 - Keyed-different safety padlocks (99552) or steel padlocks (99500). Padlocks include 2 heavy duty, re-usable lockout tags (65520) and nylon cable ties. 1-1 Group Hasp (65375) 1-1-1/2 Group Hasp (65376) 1 - Belt Pouch (51172) Electrical Power Pouch Kit Versatile lockout pouch contains useful electrical lockout devices and padlocks 2 - Tags 1 - StoPower Electrical Plug (65673) 1 - Wall Switch (65392) 1-110V Electrical Plug (65674) 1-1 Steel Safety Hasp (65375) 1 - Pouch (87943) Breaker Pouch Versatile lockout pouch contains the most commonly used electrical lockout devices 1 - Universal Multi-Pole Breaker (66321) 1-120/277V Clamp-On Breaker (65396) 1-480/600V Clamp-On Breaker (65397) 1-110V Electrical Plug 1-1 Steel Hasp 1 - Pouch (87943) 99290 Kit w/2 Safety Padlocks 99292 Kit w/2 Steel Padlocks 95548 Electrical Power Pouch Kit 95550 Kit w/ 1 Red Brady Safety Padlock 95553 Breaker Pouch Breaker Pouch Kit Contains our most popular circuit breaker lockouts 1 - Universal Multi-Pole Breaker (66321) 1-120/277V Clamp-On Breaker w/ cleat (65396) 1-480/600V Clamp-On Breaker w/ cleat (65397) 1-120V Snap-On Breaker (65387) 2 - Tags 1 - Brady Safety Padlock, Red (99552) 1 - Pouch (87943) 95538 Breaker Pouch Kit 120/277V Breaker Pouch All the devices you need to lockout most 120/277V circuit breakers 2-120V Snap-On Breaker s (65387) 2-120/277V Clamp-On Breaker w/cleats (65396) 2 - Universal Multi-Pole Breaker w/cleats (66321) 1 - Belt Pouch (51172) Optional: 2 - Keyed-different safety padlocks (99552) or steel padlocks (99500). And 2 heavy duty, re-usable lockout tags (65520) and nylon cable ties. 99300 120/277V Breaker Pouch Kit 99302 Kit w/2 Safety Padlocks & 2 Tags 99303 Kit w/2 Steel Padlocks & 2 Tags Breaker Sampler Pouch One each of our most popular circuit breaker lockouts 1-120V Snap-On Breaker (65387) 1-120/277V Clamp-On Breaker w/cleat (65396) 1-480/600V Clamp-On Breaker w/cleat (65397) 1 - Universal Multi-Pole Breaker (66321) 1 - Oversized Breaker (65329) 1 - Belt Pouch (51172) Optional: 2 - Keyed-different safety padlocks (99552) or steel padlocks (99500). And 2 heavy duty, re-usable lockout tags (65520) and nylon cable ties. 99293 Breaker Sampler Toolbox Kit 99296 Kit w/2 Safety Padlocks & 2 Tags 99297 Kit w/2 Steel Padlocks & 2 Tags 442

Standard Electrical Kits Electrical Pouch Lightweight, portable pouch contains lockout devices to secure electrical equipment. Convenient metal loops on pouch allow pouch to hang on belt. Comprehensive Breaker Pouch Lightweight, portable pouch contains lockout devices to secure electrical equipment. Convenient metal loops on pouch allow pouch to hang on belt. 1-120/277V Clamp-On Breaker (65396) 1 - Universal Multi-Pole Breaker (66321) 1-110V Electrical Plug (65674) 2 - Danger Tags 1 - Aluminum Labeled Hasp 1 - Brady Steel Padlock, 2 Shackle, Blue (99528) 1 - Pouch (65292) 1-110V Electrical Plug (65674) 3 - Wall Switch s (65392) 3 - Universal Multi-Pole Breaker s (66321) 3-120/277V Clamp-On Breaker w/cleat (65396) 2-480/600V Clamp-On Breaker w/cleat (65397) 1-120/277V Additional Cleat (102721) 1-480/600V Additional Cleat (102722) 1 - Pouch (65292) 65291 Electrical Pouch 65405 Comprehensive Breaker Pouch Brady Electrical Pouch Kit Compact and easy to use lockout pouch with the most common electrical devices 1-120/277V Clamp-On Breaker w/ cleats (65396) 1-120V Snap-On Breaker (65387) 1-110V Electrical Plug (65674) 1 - Universal Multi-Pole Breaker (66321) 1 - Wall Switch (65392) 10 - Danger Tags (LT10) 1-1-1/2 Steel Hasp (T220) 1 - Brady Key-Retaining Steel Padlock, 3/4 Shackle, Blue (143130) 1 - Large Pouch Brady Breaker Pouch Kit Compact and easy to use lockout pouch with the most common circuit breaker lockout devices 2-120V Snap-On Circuit Breaker s (65387) 2-120/277V Clamp-On Breaker s w/ cleats (65396) 2 - Universal Multi-Pole Breaker s (66321) 1 - Oversized Breaker (65329) 10 - Danger Tags (LT10) 1-1-1/2 Steel Hasp (T220) 1 - Brady Key Retaining Steel Padlock, 3/4 Shackle, Blue (143130) 1 - Large Pouch 134031 Brady Electrical Pouch Kit 134034 Brady Breaker Pouch Kit 1-800-661-9983 443

Standard Electrical Kits Brady Kit With Large Box Versatile lockout kit with essential lockout tagout components 3-120V Snap-On Breaker s (65387) 1-3-in-1 Electrical Plug (PLO23) 2 - Universal Multi-Pole Breaker s (66321) 1 - Sheet of Lock Labels (LID-2) 10 - Danger Tags (LT10) 3-1-1/2 Steel Hasps (T220) 1 - Safety Training Booklet (2112X) 1 - Plastic Utility Box 134035 Brady Kit With Large Box Electrical Starter Kit Contains everything you need to mark and secure a variety of electrical components to protect employees from electrical hazards 1 - Small 110V Electrical Plug (65674) 1 - Large 220/500V Electrical Plug (65675) 6 - Wall Switch s (65392) 6-120V Snap-On Breaker s (65387) 6-120/277V Clamp-On Breaker s w/cleats (65396) 6 - Universal Multi-Pole Breaker s (66321) 3 - Labeled Group Hasps (65960 English / 39480 Spanish) 10 - Tags with Cable Ties. Tag Legend options: - Danger Do Not Operate - Peligro No Operar - Precaucion No Hacer Funcionar 2-3/4 Shackle Brady Steel Padlock, Blue (99504) 2-2 Shackle Brady Steel Padlock, Blue (99528) 1 - Canvas Bag (65780) 65777 English Electrical Starter Kit ( Danger Do Not Operate Tags) Spanish Electrical Starter Kit ( Precaucion No Hacer 121510 Funcionar Tags) 121513 Spanish Electrical Starter Kit ( Peligro No Operar Tags) View individual devices: Basic Electrical Toolbox A handy, basic lockout toolbox kit that includes your most commonly used electrical devices 1-1 to 2.5 Gate Valve (65560) 1-1/4 to 1 Ball Valve (65666) 1 - Small 110V Electrical Plug (65674) 1-120/277V Clamp-On Breaker s w/cleats (65396) 1-480/600V Clamp-On Breaker s w/cleats (65397) 1 - Wall Switch (65392) 1 - Universal Multi-Pole Breaker (66321) 1 - Labeled Group Hasp (65960) 5 - Tags (65525) 1-3/4 Steel padlock, blue (99504) 1-2 Steel padlock, blue (99528) 1 - Toolbox (65290) Description 65289 Basic Electrical Toolbox Padlocks... page 464 Mini Cable... page 475 Cable... page 475 Ball Valve s... page 477 Gate Valve s... page 477 Plug Valve... page 477 Breaker s... page 483 Fuse s... page 486 444

Standard Electrical Kits Toolbox With Components Economical lockout toolbox with the most common electrical circuit breaker lockouts 1 - Large 220/550V Electrical Plug (65675) 1-120/277V Clamp-On Breaker s w/cleats (65396) 1-480/600V Clamp-On Breaker s w/cleats (65397) 1 - Universal Multi-Pole Breaker (66321) 2 - Tags 1 - Brady Safety Padlock, Red (99552) 1 - Toolbox (65290) Breaker Toolbox Everything you need to lockout most circuit breakers 1 - Mini Cable (50940) 2-120V Snap-On Breaker (65387) 2-120/277V Clamp-On Breaker s w/cleats (65396) 2-480/600V Clamp-On Breaker s w/cleats (65397) 1 - Universal Multi-Pole Breaker (66321) 1 - Oversized Breaker (65329) 1 - Toolbox (65290) Optional: 2 - Keyed-different safety padlocks (99552) or steel padlocks (99500). And 2 heavy duty, re-usable lockout tags (65520) and nylon cable ties. 95540 Toolbox With Components 99305 Breaker Toolbox Kit 99307 Kit w/2 Safety Padlocks & 2 Tags 99308 Kit w/2 Steel Padlocks & 2 Tags Prinzing Kits LKXSET LKX LKX-Rack Description Kit w/toolbox and Sign & Storage Rack Economy Kit w/toolbox Sign & Rack only Optional Sign & Rack Ensure equipment is de-energized or locked out in accordance with OSHA regulations Sign & Rack also available to conveniently hold the kit 3-1-1/2 Steel Hasps (T220) 3 - Blue Prinzing Padlocks (LC041-BU) 14-2 Padlock Identifier Stickers (LID-2) 1 - pkg. (10) - Tags with Ties (LT10) 3 - Single Pole Breaker s (BLO1) 2 - Multi Pole Breaker s (BLO3) 1-3-in-1 Electrical Plug (PLO23) 1 - Training Booklet (2112X) 1 - Toolbox (7 H x 12 W x 5 D) Optional: 1 Sign & Storage Rack (LKX-Rack) Electrical Toolbox Contains all of the basic devices needed to lock out circuit breakers, electrical plugs, wall switches and fuses 1 - Mini Cable (50940) 2-120V Snap-On Breaker s (65387) 2-120/277V Clamp-On Breaker s w/cleats (65396) 2-480/600V Clamp-On Breaker s w/cleats (65397) 2 - Universal Multi-Pole Breaker s (66321) 2 - Cleats for 120/277V Clamp-On s (65404) 2 - Cleats for 480/600V Clamp-On s (65406) 1 - Oversized Breaker (65329) 1-3-in-1 Electrical Plug (PLO23) 1 - Wall Switch (65392) 1 - Small Fuse Blockout (65690) 1 - Large Fuse Blockout (65691) 1 - Extra-Large Toolbox (LKP-TKLBOX) 1 - Red Belt Pouch (51172) Optional: 2 - Keyed-different safety padlocks (99552) or steel padlocks (99500). And 2 heavy duty, re-usable lockout tags (65520) and nylon cable ties. 99310 Electrical Toolbox Kit 99312 Kit w/2 Safety Padlocks & 2 Tags 99313 Kit w/2 Steel Padlocks & 2 Tags 1-800-661-9983 445

Standard Valve Kits Standard Valve Kits The valve lockout kits can be purchased with or without padlocks and tags. The padlocks included in these kits are keyed differently (each lock has its own unique key). For kits with keyed-alike padlocks (all locks can be opened with the same key), see the Personal Kits section. Valve Pouch 1-1 to 6-1/2 Adjustable Gate Valve (64057) 2-1/2 to 2-1/2 Small Ball Valve (BS07A) 1 - Plug Valve for stem dia up to 7/8 (113231) 1 - Plug Valve for stem dia 29/32 to 1-3/8 (113232) 1 - Large Pouch (50979) Optional: 2 - Keyed-different safety padlocks (99552) or steel padlocks (99500). And 2 heavy duty, re-usable lockout tags (65520) and nylon cable ties. 99679 Valve Pouch Kit 99680 Kit w/2 Safety Padlocks & 2 Tags 99681 Kit w/2 Steel Padlocks & 2 Tags Gate Valve Pouch 1-1 to 6-1/2 Adjustable Gate Valve (64057) 1 - All Purpose Cable w/ 8 sheathed cable (50943) 1 - Nylon Carrying Case (50979) Optional: 2 - Keyed-different safety padlocks (99552) or steel padlocks (99500). And 2 heavy duty, re-usable lockout tags (65520) and nylon cable ties. 101416 Gate Valve Pouch Kit 102692 Kit w/2 Safety Padlocks & 2 Tags 102693 Kit w/2 Steel Padlocks & 2 Tags Keyed Alike Padlocks Gate Valve Satchel 1-1 to 2-1/2 Gate Valve (65560) 1-2-1/2 to 5 Gate Valve (65561) 1-5 to 6-1/2 Gate Valve (65562) 1-6-1/2 to 10 Gate Valve (65563) 1 - XL Gate Valve (65564) 1 - Satchel (51173) Optional: 2 - Keyed-different safety padlocks (99552) or steel padlocks (99500). And 2 heavy duty, re-usable lockout tags (65520) and nylon cable ties. See the Personal Kits section for kits with keyed alike padlocks. 99676 Gate Valve Satchel Kit 99677 Kit w/2 Safety Padlocks & 2 Tags 99678 Kit w/2 Steel Padlocks & 2 Tags 446

Standard Valve Kits Brady Valve Kit The essential lockout devices needed for the most common valves in your facility 1-2.3 to 5 Gate Valve (65561) 10-7 Red Cable Ties (FT100X-RED) 1 - All Purpose Cable (50943) 2-1/2 to 2-1/2 Small Ball Valve (BS07A) 10 - Bilingual Tags (TG400B-ONE) 2-1-1/2 Steel Hasp (T220) 2-3/4 Brady Key-Retaining Steel Padlocks, Blue, Keyed Different (143130) 1 - Plastic Utility Box (LKP-TKLBOX) Valve Toolbox Everything you need to lock out gate, ball and butterfly valves 1 - Small Univ. Valve w/ Blocking Arm (50924 and 65402) 1 - All Purpose Cable w/ 8 Sheathed Cable (50943) 1-1 to 6-1/2 Adjustable Gate Valve (64057) 1-1/4 to 1 Ball Valve (65666) 1-1 to 2-1/2 Gate Valve (65560) 1 - Extra-Large Toolbox (LKP-TKLBOX) Optional: 2 - Keyed-different safety padlocks (99552) or steel padlocks (99500). And 2 heavy duty, re-usable lockout tags (65520) and nylon cable ties. 134033 Brady Valve Kit 99320 Gate Valve Toolbox Kit 99321 Kit w/2 Safety Padlocks & 2 Tags 99324 Kit w/2 Steel Padlocks & 2 Tags New Technical Data Sheets Download the technical sheets for over 350 lockout SKUs including lockout devices and padlocks. These sheets offer lots of information, including: Basic product description & photos Material information & temperature resistance Chemical resistance Detailed dimensional data MSDS information on the materials To view all technical data sheets visit: BradyID.com/techdata 1-800-661-9983 447

Personal Kits Personal Kits Personal lockout kits come equipped with keyed-alike padlocks, allowing all the locks in a kit to be opened with a single key. This simplifies key management and ensures that employees can quickly and easily find the right key. For kits containing padlocks that are keyed different (each padlock has its own unique key), see the standard lockout kits on previous pages. Or select a personal lockout kit without padlocks, and purchase the padlocks separately. Personal Padlock Pouch 2-1 Group Hasps (65375) 2 - Heavy Duty Tags (65520) w/ Nylon Cable Ties 2 - Keyed-alike Safety Padlocks (99552) or Steel Padlocks (99500) 1 - Belt Pouch (51172) 105969 Padlock kit w/ Keyed-Alike Safety Padlocks 105970 Padlock kit w/ Keyed-Alike Steel Padlocks Brady Operator Tagout Kit 1 - Safety Card 1 - Danger Tag 1-1-1/2 Steel Hasp (T220) 1-120/277V Clamp-On Breaker w/ cleats (65396) 1 - Brady Safety Padlock, Black (99580) 1 - Plastic Box 134030 Brady Operator Kit Prinzing Standard Belt Pack 1 - Safety Card 2 - Danger Tags 1 - Keychain 2-7 Red Cable Ties (FT100X-RED) 1-1-1/2 Steel Hasp (T220) 1-1.5 Aluminum red padlock (99615) 1 - Pouch (LKPOUCH) LK627E Prinzing Standard Belt Pack Personal Breaker Pouch Covers 120/277v and 480/600v breakers in single- and multi-pole configurations. 1-120/277V Clamp-On Breaker w/cleat (65396) 1-480/600V Clamp-On Breaker w/cleat (65397) 1 - Universal Multipole Breaker (66321) 2-1 Group Hasps (65375) 2 - Heavy Duty Tags (65520) w/ Nylon Cable Ties 1 - Belt Pouch (51172) Optional: 2 - Keyed-alike Safety Padlocks (99552) or Steel Padlocks (99500) 105966 Personal Breaker Pouch Kit 105967 Kit w/ 2 Keyed-Alike Safety Padlocks 105968 Kit w/ 2 Keyed-Alike Steel Padlocks Prinzing Cable Kit 2 - Cable Devices (CABLO) 2 - Blue Prinzing Padlocks (LC041-BU) 1-1 Steel Hasp (T218) 2 - Eng/Sp Tags w/ Ties 1 - Rugged Polyethylene Carrying Case (7 H x 12 W x 5 D) LK520B Cable Kit Prinzing Chain Kit 3-1-1/2 Steel Hasp (T220) 3 - Padlocks (LCO44-RD) 3 - Tags w/ties 1-48 Chain 1 - Durable Carrying Case (7 H x 12 W x 5 D) LK041R Kit w/ 1 Chain LK042R Kit w/ 2 Chains 448

Personal Kits Personal Basic Kit Contains the basic devices needed to lockout common circuit breakers, valves and plugs 1-1/2 to 2-1/2 Small Ball Valve (BS07A) 1-1 to 2-1/2 Gate Valve (65560) 1-120/277V Clamp-On Breaker w/ Cleat (65396) 1 - Universal Multipole Breaker (66321) 1 - Small 110V Electrical Plug (65674) 2-1 Hasps (65375) 2 - Heavy Duty Tags (65520) w/ Nylon Cable Ties 1 - Small Toolbox (105905) Optional: 2 - Keyed-alike Safety Padlocks (99552) or Steel Padlocks (99500) Personal Breaker Kit Tool box with 2 each of our most popular circuit breaker lockouts Covers 120/277v and 480/600v circuit breakers in single and multi pole configurations. 2-120/277V Clamp-On Breaker s w/ Cleats (65396) 2-480/600V Clamp-On Breaker s w/ Cleats (65397) 2 - Universal Multipole Breaker s (66321) 3-1 Red Hasps (65375) 3 - Heavy Duty Tags (65520) w/ Nylon Cable Ties 1 - Small Toolbox (105905) Optional: 3 - Keyed-alike Safety Padlocks (99552) or Steel Padlocks (99500) 104794 Personal Basic Kit 104795 Kit w/ 2 Keyed-alike Safety Padlocks 104796 Kit w/ 2 Keyed-alike Steel Padlocks 105963 Personal Breaker Kit 105964 Kit w/ 3 Keyed-Alike Safety Padlocks 105965 Kit w/ 3 Keyed-Alike Steel Padlocks Prinzing Basic Kit Rugged lockout toolbox kit with all of the basic components to get your lockout program started 5-7 Red Cable Ties (FT100X-RED) 5 - Danger Tags 3-1-1/2 Steel Hasps (T220) 1 - Keychain 2-4 x6 Magnetic Danger Sign 1 - Miniposter (PS811B) 1 - OSHA Summary Sheet 1 - Number Sheets 1 - Pad of Checklists (119076) 1 - Red Metal Toolbox LK330E LK907E Description Prinzing Basic Kit Kit w/3 Aluminum 1.5 Keyed Alike Red Padlocks Prinzing Kit Rugged lockout toolbox kit with all of the basic components to get your lockout program started 5-7 Red Cable Ties (FT100X-RED) 5 - Danger Tags 3-1-1/2 Steel Hasps (T220) 1 - Keychain 2-4 x6 Magnetic Danger Sign 1 - Miniposter (PS811B) 1 - OSHA Summary Sheet 1 - Number Sheets 1 - AC Sensor (65269) 3 - Aluminum 1.5 Keyed Alike Red Padlocks 1 - Red Metal Toolbox LK331E Description Prinzing Kit 1-800-661-9983 449

Personal Kits Personal Electrical Kit Contains lockouts for use on most circuit breakers, electrical plugs and disconnect switches. 1 - Mini Cable (50940) 1-3-in-1 Electrical Plug (PLO23) 2-120/277V Clamp-On Breaker s w/ Cleats (65396) 1-480/600V Clamp-On Breaker w/ Cleat (65397) 2 - Universal Multipole Breaker (66321) 1 - Oversized Breaker (65329) 3-1 Group Hasps (65375) 3 - Heavy Duty Tags (65520) w/ Nylon Cable Ties 1 - Medium Toolbox (105906) Optional: 3 - Keyed-alike Safety Padlocks (105886) or Steel Padlocks (118977) Personal Valve Kit Contains lockouts for use on a wide range of gate and ball valves 1-1 to 6-1/2 Adjustable Gate Valve (64057) 1-1 to 2-1/2 Gate Valve (65560) 1-1/2 to 2-1/2 Small Ball Valve (BS07A) 1 - All Purpose Cable (50943) 3-1 Group Hasps (65375) 3 - Heavy Duty Tags (65520) w/ Nylon Cable Ties 1 - Medium Toolbox (105906) Optional: 3 - Keyed-alike Safety Padlocks (105886) or Steel Padlocks (118977) 105960 Personal Electrical Kit 105961 Kit w/3 Keyed-alike Safety Padlocks 105962 Kit w/3 Keyed-alike Steel Padlocks 105957 Personal Valve Kit 105958 Kit w/ 3 Keyed-Alike Safety Padlocks 105959 Kit w/ 3 Keyed-Alike Steel Padlocks View individual devices: Personal Valve & Electrical Kit Provides everything you need to lockout circuit breakers, plugs and valves of various types and sizes 1 - All Purpose Cable (50943) 1-1 to 6-1/2 Adjustable Gate Valve (64057) 1 - Plug Valve for stem dia up to 7/8 (113231) 1 - Plug Valve for stem dia 9/32 to 1-3/8 (113232) 1-1/2 to 2-1/2 Small Ball Valve (BS07A) 1-3-in-1 Electrical Plug (PLO23) 2-120/277V Clamp-On Breaker s w/ Cleats (65396) 1-480/600V Clamp-On Breaker w/ Cleat (65397) 2 - Universal Multipole Breaker s (66321) 3-1 Group Hasps (65375) 3 - Heavy Duty Tags (65520) w/ Nylon Cable Ties 1 - Medium Toolbox (105906) Optional: 3 - Keyed-alike Safety Padlocks (105886) or Steel Padlocks (118977) Padlocks... page 464 Mini Cable... page 475 Cable... page 475 Ball Valve s... page 477 Gate Valve s... page 477 Plug Valve... page 477 Breaker s... page 483 Fuse s... page 486 105954 Personal Valve & Electrical Kit 105955 Kit w/ 3 Keyed-Alike Safety Padlocks 105956 Kit w/ 3 Keyed-Alike Steel Padlocks 450

Custom Storage Custom Storage Create your custom lockout kits by picking one of the storage/carrying cases below and filling it with the lockout devices you need! Belt Pouch Made of heavy duty nylon with loops for hanging on a belt Dimensions: 4-3/4 H x 7-1/2 W x 2 D 51172 Belt Pouch Large Pouch Made of nylon with attachment loop on back Dimensions: 8 H x 7 W x 3 D 50979 Large Pouch w/ Plastic Zipper 121502 Large Pouch w/ Metal Zipper Security Bag Made of rugged canvas with drawstring Capable of being locked closed Dimensions: 9-3/4 H x 18 W 65780 Security Bag Satchel Made of 1000 denier red cordura nylon with 39 shoulder strap Includes latchable front pocket and two side mesh holders Extra-Large Toolbox Made of rugged polyethylene and includes a removable organizer tray Capable of being locked closed Duffel Bag Made of 600 denier polyester with 39 removable shoulder strap and 8 inside pockets Dimensions: 10 H x 16-1/2 W x 8-1/2 D Dimensions: 14 H x 4 W x 15 D Dimensions: 5 H x 12 W x 7 D Description Description Description 51173 Satchel LKX-TKLBOX Toolbox 99162 Duffel Bag Toolboxes Made of rugged polypropylene with nickel-plated steel clasps and removeable tray Two handy storage pockets built into lid Small: 7.1 H x 14 W x 5.5 D Medium: 7.8 H x 16.2 W x 7.3 D 105905 Small Toolbox 105906 Medium Toolbox Prinzing Metal Cabinet All metal, yellow powder-coated cabinet comes with one adjustable shelf (extra shelves available) Capable of being locked closed Can also be easily wall mounted using predrilled holes in back safety tips printed on inside door Dimensions: 16 H x 14 W x 6 D Ready Access Station Made of thermformed polyproylene Semi-transparent hinged cover with locking mechanism Slots in back for wall mounting and carrying handle for easy portability 4 Small detachable hanging hooks Compartment: 4.25 H x 16 W x 5.12 D Dimensions: 17 H x 17 W x 6.75 D Description Description LC252M Metal Cabinet 105942 Ready Access Station (empty) LC254M Extra Shelf 1-800-661-9983 451

Stations Stations Brady s Stations ensure that lockout devices are properly stored and always accessible when needed. These Stations are a great place to centralize lockout activity needs by organizing the tools, padlocks and padlock keys in one location. Available in portable and wall-mounted styles, these stations are designed with the durability required for an industrial workplace, and can be locked to prevent theft and unauthorized usage. Combined / Group Box Station Lockable all metal, yellow powder-coated cabinet comes with one adjustable shelf (extra shelves available) Included lock box attaches to bottom of cabinet (holds 8-10 locks) Cabinet dimensions: 16 H x 14 W x 6 D Lock box: 6 H x 15 W x 3 D 1-120V Snap-On Breaker s (65387) 1-120/277V Clamp-On Breaker w/cleats (65396) 1-480/600V Clamp-On Breaker w/cleats (65397) 1 - Universal Multi-Pole Breaker (66321) 1 - Oversized Breaker (65329) 1 - Wall Switch (65392) 1-110V Electrical Plug (65674) 1-3-in-1 Electrical Plug (PLO23) 1-1 to 2-1/2 Gate Valve (65560) 1-1 to 6-1/2 Adjustable Gate Valve (64057) 6 - Keyed-different safety padlocks (99552) or steel padlocks (99500) 6 - Heavy duty, re-usable lockout tags (65520) w/ nylon cable ties Industrial Strength Station All metal, yellow powder-coated cabinet comes with one adjustable shelf (extra shelves available) safety tips on inside door Wall mounted or easily transported Cabinet dimensions: 16 H x 14 W x 6 D 3 - Red Safety padlocks (99552) 3 - Yellow Safety padlocks (99570) 1-2-1/2 to 5 Safetee Donut (SDO4) 1-1 to 2-1/2 Safetee Donut (SD02) 1 - Single pole breaker lockout (BLO1) 10 - tags with ties (LT10) 2 - Multi pole breaker lockout (BLO3) 1-1 Multiple lockout device (T218) 1 - Single pole breaker lockout (BLO4) 1-1-1/2 Multiple lockout device (T220) 1-3-in-1 Electrical plug lockout (PLO23) 1 - Small plug lockout (PLO21) 99709 Station w/ Components & 6 Safety Padlocks, 12 Tags 99710 Station w/ Components & 6 Steel Padlocks, 12 Tags LC252M Metal Cabinet (empty) LG252M Metal Wall Lock Box Only LC254M Extra Shelf LC251M LC252M LC254M Description Industrial Strength Station Metal Cabinet (empty) Extra Shelf 452

Stations Ready Access Station Made of thermformed polyproylene for rugged durability Semi-transparent hinged cover with locking mechanism Pictured Ready Access Valve & Electrical Station Ready Access Valve Station 1 - Ready Access Station (105942) 2 - Adjustable Gate Valve s (64057) 1 - All Purpose Cable (50943) 2 - Ball Valve s (BSO7A) 2-1 Group Hasps (65375) 1-1.5 Group Hasp (65376) Optional: 6 - Keyed different safety padlocks (99552) or steel padlocks (99500) 6 - Heavy duty, re-usable lockout tags (65520) w/ nylon cable ties 105936 Valve Station Kit 105937 Kit w/ 6 Safety Padlocks & Tags 105938 Kit w/ 6 Steel Padlocks & Tags 105942 Ready Access Station (empty) Ready Access Electrical Station Slots in back for wall mounting as well as attachable carrying handle for portability 4 detachable hanging hooks inside compartment Storage compartment: 4.25 H x 16 W x 5.12 D Cabinet dimensions: 17 H x 17 W x 6.75 D 1 - Ready Access Station (105942) 2-3-in-1 Electrical Plug s (PLO23) 1 - Mini Cable (50940) 2-120/277V Clamp-On Breaker s w/ cleats (65396) 2-480/600V Clamp-On Breaker s w/ cleats (65397) 2 - Universal Multipole Breaker s (66321) 1 - Oversized Breaker (65329) 2-1 Group Hasps (65375) 1-1.5 Group Hasps (65376) Optional: 6 - Keyed different safety padlocks (99552) or steel padlocks (99500) 6 - Heavy duty, re-usable lockout tags (65520) w/ nylon cable ties Ready Access Valve & Electrical Station 1 - Ready Access Station (105942) 1 - Adjustable Gate Valve (64057) 1 - All Purpose Cable (50943) 1 - Ball Valve (BSO7A) 1-3-in-1 Electrical Plug (PLO23) 2-120/277V Clamp-On Breaker s w/ cleats (65396) 1-480/600V Clamp-On Breaker w/ cleat (65397) 2 - Universal Multipole Breaker s (66321) 2-1 Group Hasps (65375) 1-1.5 Group Hasp (65376) Optional: 6 - Keyed-different safety padlocks (99552) or steel padlocks (99500) 6 - Heavy duty, re-usable lockout tags (65520) w/ nylon cable ties 105939 Electrical Station Kit 105940 Kit w/ 6 Safety Padlocks & Tags 105941 Kit w/ 6 Steel Padlocks & Tags 105942 Ready Access Station (empty) 105933 Valve & Electrical Station Kit 105934 Kit w/ 6 Safety Padlocks & Tags 105935 Kit w/ 6 Steel Padlocks & Tags 105942 Ready Access Station (empty) Ready Access Padlock Station Holds up to 10 padlocks, 6 hasps and 10 tags Made of thermformed polyproylene for rugged durability Semi-transparent hinged cover with locking mechanism Slots in back for wall mounting as well as attachable carrying handle for portability Space-saving design delivers footprint half the size of competitors Dimensions: 17 H x 13.25 W x 2.5 D *Pictured Ready Access Station with 10 Padlocks Padlock Station w/5 Padlocks: 1 - Ready Access Padlock Station (105932) 5 - Keyed-different safety padlocks (99552) or steel padlocks (99500) 5 - Heavy Duty, re-usable lockout tags (65520) w/nylon cable tie 2-1 Group Hasps (65375) 2-1-1/2 Group Hasps (65376) 105928 Station w/ 5 Safety Padlocks 105929 Station w/ 5 Steel Padlocks 105932 Ready Access Padlock Station (empty) Padlock Station w/10 Padlocks: 1 - ReadyAccess Padlock Station (105932) 10 - Keyed-different safety padlocks (99552) or steel padlocks (99500) 10 - Heavy duty, re-usable lockout tags (65520) w/ nylon cable ties 3-1 Group Hasps (65375) 3-1-1/2 Group Hasps (65376) 105930 Station w/ 10 Safety Padlocks 105931 Station w/ 10 Steel Padlocks 105932 Ready Access Padlock Station (empty) 1-800-661-9983 453

Stations Shown without optional lockable clear acrylic door Extra-Large Station Provides everything you need to lockout most mechanical and electrical control points Constructed of sturdy polystyrene with predrilled holes for easy wall mounting Pegboard-style holes for hooks drilled into back and sides (includes 8 hooks) Built-in lock rail holds 20-25 locks Dimensions: 30 H x 25 W x 5-1/4 D Available with or without lockable door 1 - All Purpose Cable w/ 8 Sheathed Cable (50943) 1 - Large Univ. Valve w/blocking Arm (50899 and 65403) 2-120V Snap-On Breaker s (65387) 2-120/277V Clamp-On Breaker s (65396) 2-480/600V Clamp-On Breaker s (65397) 2 - Universal Multi-Pole Breaker s (66321) 1 - Oversized Breaker (65329) 2 - Cleats for 120/277V Clamp-On s (65404) 2 - Cleats for 480/600V Clamp-On s (65406) 1 - Wall Switch (65392) 1-110V Electrical Plug (65674) 1-3-in-1 Electrical Plug (PLO23) 1-1/4 to 1 Ball Valve (65666) 1-1-1/4 to 3 Ball Valve (65669) 2-1 to 2-1/2 Gate Valve s (65560) 1-1 to 6-1/2 Adjustable Gate Valve (64057) 2 - Labeled Hasps (65960) 18 - Keyed different safety padlocks (99552) or steel padlocks (99500) 25 - Heavy duty, re-usable lockout tags (65520) w/ nylon cable ties 1 Station with Station legend Shown with optional lockable clear acrylic door Large Station Provides everything you need to lock out most types of electrical control points Constructed of sturdy polystyrene with predrilled holes for easy wall mounting Pegboard-style holes for hooks drilled into back (includes 6 hooks) Built-in lock rail holds 15-20 locks Dimensions: 26 H x 19-1/2 W x 5 D Available with or without lockable door 1 - All Purpose Cable w/ 8 Sheathed Cable (50943) 1 - Large Univ. Valve w/blocking Arm (50899 and 65403) 1-110V Electrical Plug (65674) 1-3-in-1 Electrical Plug (PLO23) 1-1/4 to 1 Ball Valve (65666) 1-1 to 2-1/2 Gate Valve (65560) 1-1 to 6-1/2 Adj. Gate Valve (64057) 2 - Labeled Hasps (65960) 12 - Keyed different safety padlocks (99552) or steel padlocks (99500) 25 - Heavy duty, re-usable lockout tags w/ nylon cable ties. Tag legend options: - Danger Do Not Operate (65520) - Precaucion No Hacer Funcionar (121518) - Peligro No Operar (98219) 1 Station with Station or Estacion de Bloqueo legend Small Station Provides everything you need to lockout most types of electrical control points Constructed of sturdy polystyrene with predrilled holes for easy wall mounting Pegboard-style holes for hooks drilled into back (includes 4 hooks) Built-in lock rail holds 10-15 locks Dimensions: 18 H x 12 W x 4 D 1 - Mini Cable (50940) 2-120V Snap-On Breaker s (65387) 2-120/277V Clamp-On Breaker s w/ cleats (65396) 2-480/600V Clamp-On Breaker s w/ cleats (65397) 2 - Universal Multi-Pole Breaker s (66321) 1 - Oversized Breaker (65329) 1 - Wall Switch (65392) 1-110V Electrical Plug (65674) 1-3-in-1 Electrical Plug (PLO23) 1 - Small fuse blockout (65690) 1 - Large fuse blockout (65691) 2 - Labeled Hasps (65960) 6 - Keyed different safety padlocks (99552) or steel padlocks (99500) 12 - Heavy duty, re-usable lockout tags (65520) w/ nylon cable ties 1 Station with Station legend Open Style Without Doors 99693 Station w/ Components and 18 Safety Padlocks, 25 Tags 99694 Station w/ Components and 18 Steel Padlocks, 25 Tags 50993 Extra-Large Station (empty) Enclosed Style With Lockable Doors 99696 Station w/ Components and 18 Safety Padlocks, 25 Tags 99700 Station w/ Components and 18 Steel Padlocks, 25 Tags 50995 Extra-Large Enclosed Station (empty) Open Style Without Doors English Station w/ Components and 12 99699 Safety Padlocks, 25 Danger Do Not Operate Tags Spanish Station w/ Components and 12 121508 Safety Padlocks, 25 Precaucion No Hacer Funcionar Tags Spanish Station w/ Components and 12 121512 Safety Padlocks, 25 Peligro No Operar Tags English Station w/ Components and 99697 12 Steel Padlocks, 25 Danger Do Not Operate Tags 50994 English Open Style Station (empty) 121509 Spanish Open Style Station (empty) Enclosed Style With Lockable Doors English Enclosed Station w/ Components 99703 and 12 Safety Padlocks, 25 Danger Do Not Operate Tags English Enclosed Station w/ Components 99704 and 12 Steel Padlocks, 25 Danger Do Not Operate Tags 50996 English Enclosed Station (empty) 99706 Station w/ Components & 6 Safety Padlocks, 12 Tags 99707 Station w/ Components & 6 Steel Padlocks, 12 Tags 50997 Small Station (empty) 454

Stations Prinzing Starter Station Heavy duty lockout cabinet with the essential items needed to keep your facility safe and locked out 1 - Ball Valve (BS07A) 2-2.5 to 5 Gate Valve (65561) 2-3-in-1 Electrical Plug (PLO23) 6-1-1/2 Steel Hasp (T220) 50-7 Red Cable Ties (FT100X-RED) 25 - Tags (TG027E) 3 - Red Brady Safety Padlocks, Key-Different (99552) 3 - Yellow Brady Safety Padlocks, Key-Different (99570) 1 - Cabinet Station (LC977A) LC517E Description Prinzing Starter Station Prinzing Valve & Electrical Station Heavy duty lockout cabinet station contains many common valve and electrical lockout devices needed in a facility 1 - Ball Valve (BS07A) 3 - No-hole Breaker (BL04) 3 - Breaker, Multi-pole (BL07) 6-1-1/2 Steel Hasp (T220) 2-3-in-1 Electrical Plug (PLO23) 3 - Wall Switch (WSLO) 2-2.5 to 5 Gate Valve (65561) 50-7 Red Cable Ties (FT100X-RED) 1 - OSHA Summary Sheet 1 - miniposter (PS811B) 25 - Tags (TG027E) 1 - Cabinet Station (LC977A) Station Fully equipped lockout tagout station to store all of your facility devices 1-1/2 to 2-1/2 Ball Valve (BS07A) 2-2.3 to 5 Gate Valve s (65561) 2-120/277V Clamp-On Breaker w/ cleats (65396) 3 - Universal Multi-Pole Breaker s (66321) 2-3-in-1 Electrical Plug s (PLO23) 2 - Wall Switch s (65392) 6-1-1/2 Steel Hasps (T220) 1 - OSHA Summary Sheet 100 - Red Cable Ties (FT100) 25 - Danger Tags (TG027E) 3 - Brady Safety Padlocks, Yellow, Keyed Different (99570) 3 - Brady Safety Padlocks, Red, Keyed Different (99552) 1 - Cabinet (LC584E) LC518E Prinzing Valve & Electrical Station 134036 Station May We Also Suggest: Station V-Sign Safety Center Provides ready access to locks, tags, lockout devices and information Made of tough acrylic plastic Station size: 30 H x 24 W x 4-1/2 D 6 - Multi-color steel padlocks 2-10 pack English lockout tags with ties (LT10) 5-1-1/2 lockout hasps (T220) 25 - English Safety booklets (2112X) Bilingual Safety Center Provides ready access to locks, tags, lockout devices and information Made of tough acrylic plastic Station size: 30 H x 24 W x 4-1/2 D 6 - Multi-color padlocks 2-10 pack Bilingual lockout tags with ties (TG400B-10) 5-1-1/2 lockout hasps (T220) 15 - English Safety booklets (2112X) 10 - Spanish Safety booklets (2112SPX) Enhance the visibility of your Station with this V-shaped polyethylene sign Sign size: 8 x 9 x 1 flange (overall width is 14 ) 3001 Safety Center 3012 Board Only 3002 Bilingual Safety Center 3013 Bilingual Board Only 66328 Stations V-Sign 1-800-661-9983 455

Stations Prinzing Center Large, easily identifiable lockout station to hold all of the necessary lockout items for your facility 2-1-1/2 Steel Hasp (T220) 1-2.5 to 5 Gate Valve (65561) 1-3-in-1 Electrical Plug (PLO23) 1 - Small Plug (PLO21) 1-1/2 to 2-1/2 Small Ball Valve (BS07A) 2-4 x6 Magnetic Danger Sign 1 - Pad of checklists (119076) 1 - miniposter (PS811B) 10 - Danger Tags 2 - Aluminum Padlocks, 1.5 Shackle, Keyed Different, Red (99615) 2 - Aluminum Padlocks, 1.5 Shackle, Keyed Different, Blue (99616) 2 - Aluminum Padlocks, 1.5 Shackle, Keyed Different, Yellow (99618) 2 - Aluminum Padlocks, 1.5 Shackle, Keyed Different, Green (99617) 1 - Large Yellow Board (LC501E) Prinzing Micro Station Compact and convenient mini-lockout station for essential items 5-7 Red Cable Ties (FT100X-RED) 1-1-1/2 Steel Hasp (T220) 2 - Tags (LT1) 1-3/4 Red Key-Retaining Steel Padlock (143126) 1 - Micro Board (LC226A) KT226A Prinzing Micro Station LC226A Board Only Prinzing Board Unfilled, wall mounted Center olds many of your most common devices needed around the facility for easy access and storage LC744E Prinzing Board Description LC502E Prinzing Center LC501E Prinzing Board Only 5-Lock Board Dimensions: 11-1/2 H x 15-1/2 W Prinzing Economy Center 5 - Keyed different safety padlocks (99552) or steel padlocks (99500) 1-1 metal hasp (65375) 1-1-1/2 metal hasp (65376) 12 - heavy duty tags (65520) Description Dimensions: 9 H x 12 W 10 - Tags (LT10) 1-1.5 Hasp (T220) 4 - Key Retaining Steel Locks, 3/4 Shackle Blue (143130) 1 - Center (LC202G) 51181 5-Lock Board & 5 Safety Padlocks 51186 5-Lock Board & 5 Steel Padlocks 50989 5-Lock Board (Board Only) LC203G LC202G Description Prinzing Station Prinzing Board Only Did you know? Lock Boards Lock boards contribute to a successful lockout program by providing storage at the point of need for all of your devices Boards are made of 3/16 thick bright yellow acrylic with acrylic lock rails. Tag pockets are made of clear polycarbonate and will hold tags up to 3 wide. 456

Stations May We Also Suggest: Ready Access Padlock Station Prinzing Economy Center Dimensions: 14 H x 14 W 10 - Tags (LT10) 1-1 Hasp (T218) 1-1.5 Hasp (T220) 2-1-1/2 Hasps 24 - Heavy Duty Tags 6 - Key Retaining Steel Locks, 3/4 shackle (Green, Yellow, Black, White, Blue, Red) 1 - Center (3004Y) Prinzing Bilingual Center Dimensions: 14 H x 14 W 10 - Bilingual Tags (TG400B-ONE) 1-1 Hasp (T218) 1-1.5 Hasp (T220) 6 - Key Retaining Steel Locks, 3/4 shackle (Green, Yellow, Black, White, Blue, Red) 1 - Bilingual Center (LC210G) Wall mountable, thermformed polyproylene cabinet with semi-transparent lockable door Holds up to 10 padlocks, 6 hasps and 10 tags See page 453 for more information. Description Description 3003Y Prinzing Economy Center LC211G Prinzing Bilingual Center 3004Y Board Only LC210G Prinzing Bilingual Board Only 10-Lock Board Dimensions: 13-1/2 H x 13-1/2 W 10 - Keyed different safety padlocks (99552) or steel padlocks (99500) 2-1 hasps (65375) 2-1-1/2 hasps (65376) 12 - Heavy duty tags (65520) 51187 10-Lock Board & 10 Safety Padlocks 51188 10-Lock Board & 10 Steel Padlocks 50990 10-Lock Board (Board Only) 20-Lock Board Dimensions: 23-1/2 H x 11-1/2 W 20 - Keyed different safety padlocks (99552) or steel padlocks (99500) 2-1 hasps (65375) 2-1-1/2 hasps (65376) 24 - Heavy duty tags.tag legend options: - Danger Do Not Operate (65520) - Peligro No Operar (98219) - Precaucion No Hacer Funcionar (121518) 20-Lock Board w/ 20 Safety Padlocks 51189 Station Board Danger Do Not Operate Tags 20-Lock Board & 20 Steel Padlocks 51194 Station Board Danger Do Not Operate Tags 20-Lock Board w/ 20 Safety Padlocks 121507 Estacion de Bloqueo Board Precaucion No Hacer Funcionar Tags 20-Lock Board w/ 20 Safety Padlocks 121511 Estacion de Bloqueo Board Peligro No Operar Tags 50991 20-Lock Station Board Only 121506 20-Lock Estacion de Bloqueo Board Only 36-Lock Board Dimensions: 21-1/2 H x 23-1/2 W 36 - Keyed different safety padlocks (99552) or steel padlocks (99500) 3-1 hasps (65375) 3-1-1/2 hasps (65376) 36 - Heavy duty tags (65520) 51195 36-Lock Board & 36 Safety Padlocks 51196 36-Lock Board & 36 Steel Padlocks 50992 36-Lock Board (Board Only) 457

Energy Source Tags Energy Source Tags Energy source tags can be used to mark your facility s points of control for energy sources. These tags help make the lockout process quicker, safer and easier. These energy source tags are made of plastic and available with color coded and alpha numeric options. A variety of pre-printed energy source tags are available or they can be customized to meet your specific application. 1.5 x 3 tags are constructed with B-401 Rigid Plastic Rounded corners and one hole included Energy Source Tag Guide Brady offers a number of options based on your needs. Use the guide below to ensure that you are selecting the appropriate tag based on your application. Custom Tags Also Available. Contact Brady to find out more. Abbr. Color Energy Source Number of Energy Points* CP Orange on White Control Panel 1 thru 9 E Red on White Electrical 1 thru 9 G Purple on White Gas 1 thru 9 V Black on White Valve 1 thru 9 W White on Green Water 1 thru 9 S White on Red Steam 1 thru 9 S Black on Orange Steam 1 thru 9 P White on Blue Pneumatic / Air 1 thru 9 * Choice of numbers supports machines with multiple energy points. Control Panel Legend Picto Color Qty. 105634 CP-1 - Orange on White 5 105674 CP-1 - Orange on White 25 105635 CP-2 - Orange on White 5 105675 CP-2 - Orange on White 25 105636 CP-3 - Orange on White 5 105676 CP-3 - Orange on White 25 105637 CP-4 - Orange on White 5 105677 CP-4 - Orange on White 25 105638 CP-5 - Orange on White 5 105673 CP-5 - Orange on White 25 * Control Panel tags supplied with an adhesive back. Electrical Legend Picto Color Qty. 105639 E-1 Electric Bolt Red on White 5 105679 E-1 Electric Bolt Red on White 25 105640 E-2 Electric Bolt Red on White 5 105680 E-2 Electric Bolt Red on White 25 105641 E-3 Electric Bolt Red on White 5 105681 E-3 Electric Bolt Red on White 25 105642 E-4 Electric Bolt Red on White 5 105682 E-4 Electric Bolt Red on White 25 105643 E-5 Electric Bolt Red on White 5 105683 E-5 Electric Bolt Red on White 25 * Electrical tags supplied with an adhesive back. 458

Energy Source Tags Water Legend Picto Color Qty. 105644 W-1 Spout White on Green 5 105684 W-1 Spout White on Green 25 105645 W-2 Spout White on Green 5 105685 W-2 Spout White on Green 25 105646 W-3 Spout White on Green 5 105686 W-3 Spout White on Green 25 105647 W-4 Spout White on Green 5 105687 W-4 Spout White on Green 25 105648 W-5 Spout White on Green 5 105688 W-5 Spout White on Green 25 Valve Legend Picto Color Qty. 105664 V-1 Spout Black on White 5 105704 V-1 Spout Black on White 25 105665 V-2 Spout Black on White 5 105705 V-2 Spout Black on White 25 105666 V-3 Spout Black on White 5 105706 V-3 Spout Black on White 25 105667 V-4 Spout Black on White 5 105707 V-4 Spout Black on White 25 105668 V-5 Spout Black on White 5 105708 V-5 Spout Black on White 25 Steam Legend Picto Color Qty. 105649 S-1 Single Pressure Steam Gauge White on Red 5 105689 S-1 Single Pressure Steam Gauge White on Red 25 105650 S-2 Single Pressure Steam Gauge White on Red 5 105690 S-2 Single Pressure Steam Gauge White on Red 25 105651 S-3 Single Pressure Steam Gauge White on Red 5 105691 S-3 Single Pressure Steam Gauge White on Red 25 105652 S-4 Single Pressure Steam Gauge White on Red 5 105692 S-4 Single Pressure Steam Gauge White on Red 25 105653 S-5 Single Pressure Steam Gauge White on Red 5 105693 S-5 Single Pressure Steam Gauge White on Red 25 Steam Legend Picto Color Qty. 105659 S-1 Single Pressure Steam Gauge Black on Orange 5 105699 S-1 Single Pressure Steam Gauge Black on Orange 25 105660 S-2 Single Pressure Steam Gauge Black on Orange 5 105670 S-2 Single Pressure Steam Gauge Black on Orange 25 105661 S-3 Single Pressure Steam Gauge Black on Orange 5 105671 S-3 Single Pressure Steam Gauge Black on Orange 25 105662 S-4 Single Pressure Steam Gauge Black on Orange 5 105672 S-4 Single Pressure Steam Gauge Black on Orange 25 105663 S-5 Single Pressure Steam Gauge Black on Orange 5 105673 S-5 Single Pressure Steam Gauge Black on Orange 25 Pneumatic / Air Legend Picto Color Qty. 105654 P-1 Double Pressure Air Gauge White on Blue 5 105694 P-1 Double Pressure Air Gauge White on Blue 25 105655 P-2 Double Pressure Air Gauge White on Blue 5 105695 P-2 Double Pressure Air Gauge White on Blue 25 105656 P-3 Double Pressure Air Gauge White on Blue 5 105696 P-3 Double Pressure Air Gauge White on Blue 25 105657 P-4 Double Pressure Air Gauge White on Blue 5 105697 P-4 Double Pressure Air Gauge White on Blue 25 105658 P-5 Double Pressure Air Gauge White on Blue 5 105698 P-5 Double Pressure Air Gauge White on Blue 25 Gas Legend Picto Color Qty. 105669 G-1 Double Pressure Gas Gauge Purple on White 5 105709 G-1 Double Pressure Gas Gauge Purple on White 25 105670 G-2 Double Pressure Gas Gauge Purple on White 5 105710 G-2 Double Pressure Gas Gauge Purple on White 25 105671 G-3 Double Pressure Gas Gauge Purple on White 5 105711 G-3 Double Pressure Gas Gauge Purple on White 25 105672 G-4 Double Pressure Gas Gauge Purple on White 5 105712 G-4 Double Pressure Gas Gauge Purple on White 25 105673 G-5 Double Pressure Gas Gauge Purple on White 5 105713 G-5 Double Pressure Gas Gauge Purple on White 25 1-800-661-9983 459

Tags OSHA Regulations The following requirements apply only to tags used as tagout devices (i.e., tags used alone without locks). Tags used in combination with locks are not required to meet the same restrictions as tagout devices. Tagout devices must: Be provided by the employer Employ a means of attachment that is substantial enough to prevent accidental removal. The means of Be standardized by size, shape or color attachment must be of a non-reusable type, attachable Be distinguishable from tags used for other purposes by hand, self-locking, and non-releasable with a Be understandable to all employees minimum unlocking strength of no less than 50 pounds. Identify the individual who applied the tag Withstand the usage environment to which they are exposed for the maximum period of time that exposure is intended. Tag should not deteriorate or the message become illegible when exposed to weather, wet or damp conditions, chemical or corrosive environments. Warn against hazardous conditions if the machine or equipment is energized. Tag shall also include a legend such as the following: Do Not Operate, Do Not Start, Do Not Open, Do Not Close, etc. Standard Tags Communicate safety and lockout information at the point of need with Brady s wide selection of OSHA-compliant Tagout tags. Brady s Tags come in a variety of materials and legends to suit your application needs. How to Order Tags 1. Select from the materials below based on your application 2. Choose the tag legend for your tag 3. Order by part number for desired reverse side legend Available Tag Materials: Heavy Duty Polyester (B-837) Durable polyester laminate completely encapsulates and protects graphics Designed to withstand moisture, grease, chemicals and extreme temperatures Accepts pencil, pen and marker. Pen and marker can be completely erased using isopropyl alcohol Exceeds OSHA pull requirement withstanding up to 80 lbs of pull force 3/8 dia. heavy-duty brass grommet Includes OSHA-compliant nylon fasteners Economy Polyester (B-851) Rigid polyester surface is easy to write on and stays legible longer than cardstock Exceeds OSHA 50 lb. pull requirement for tagout devices 3/8 dia. rolled brass eyelet accepts most padlock shackles Includes OSHA-compliant nylon fasteners Cardstock (B-853) Cost-effective tags designed for onetime use Does NOT meet OSHA 50 lb. pull test for tagout devices, but can be used in conjunction with locks (see OSHA Tag Requirements above) 3/8 dia. rolled brass eyelet accepts most padlock shackles Includes attachment strings 460

Tags Reverse Legend Qty. Heavy Duty Polyester 5-1 2 x 3 65502 Side B 25 65535 Side F 25 65670 Side G 25 Economy Polyester 5-3 4 x 3 66050 Side B 25 66051 Side F 25 66052 Side G 25 Cardstock 5-3 4 x 3 65407 Side B 25 65408 Side F 25 65440 Side G 25 Reverse Legend Qty. Heavy Duty Polyester 5-1 2 x 3 65520 Side B 25 65525 Side F 25 65671 Side G 25 Economy Polyester 5-3 4 x 3 66063 Side B 25 66064 Side F 25 66065 Side G 25 Cardstock 5-3 4 x 3 65451 Side B 25 65452 Side F 25 65453 Side G 25 Reverse Legend Qty. Heavy Duty Polyester 5-1 2 x 3 65515 Side B 25 65524 Side F 25 133489 Side G 25 Economy Polyester 5-3 4 x 3 66061 Side B 25 66062 Side F 25 133490 Side G 25 Cardstock 5-3 4 x 3 133491 Side B 25 65450 Side F 25 133492 Side G 25 Reverse Legend Qty. Heavy Duty Polyester 5-1 2 x 3 65526 Side B 25 65527 Side F 25 133493 Side G 25 Economy Polyester 5-3 4 x 3 66066 Side B 25 66067 Side F 25 133494 Side G 25 Cardstock 5-3 4 x 3 65454 Side B 25 65455 Side F 25 133495 Side G 25 Reverse Legend Qty. Heavy Duty Polyester 5-1 2 x 3 65505 Side B 25 65523 Side F 25 133496 Side G 25 Economy Polyester 5-3 4 x 3 133497 Side B 25 133498 Side F 25 133499 Side G 25 Cardstock 5-3 4 x 3 65445 Side B 25 65446 Side F 25 133544 Side G 25 Reverse Legend Qty. Heavy Duty Polyester 5-1 2 x 3 65503 Side B 25 65521 Side F 25 133545 Side G 25 Economy Polyester 5-3 4 x 3 66053 Side B 25 66054 Side F 25 133546 Side G 25 Cardstock 5-3 4 x 3 65441 Side B 25 65442 Side F 25 133547 Side G 25 Reverse Legend Qty. Heavy Duty Polyester 5-1 2 x 3 65504 Side B 25 65522 Side F 25 133548 Side G 25 Economy Polyester 5-3 4 x 3 66055 Side B 25 66056 Side F 25 133549 Side G 25 Cardstock 5-3 4 x 3 65443 Side B 25 65444 Side F 25 133550 Side G 25 Reverse Legend Qty. Heavy Duty Polyester 5-1 2 x 3 133551 Side B 25 133552 Side F 25 133553 Side G 25 Economy Polyester 5-3 4 x 3 50198 Side B 25 50199 Side F 25 133554 Side G 25 Cardstock 5-3 4 x 3 133555 Side B 25 50250 Side F 25 133556 Side G 25 Reverse Legend Qty. Heavy Duty Polyester 5-1 2 x 3 65506 Side B 25 65534 Side F 25 133557 Side G 25 Economy Polyester 5-3 4 x 3 133558 Side B 25 66060 Side F 25 133559 Side G 25 Cardstock 5-3 4 x 3 65447 Side B 25 65448 Side F 25 133560 Side G 25 Reverse Legend Qty. Heavy Duty Polyester 5-1 2 x 3 133561 Side B 25 50258 Side F 25 133562 Side G 25 Economy Polyester 5-3 4 x 3 133563 Side B 25 133564 Side F 25 133565 Side G 25 Cardstock 5-3 4 x 3 50261 Side B 25 133566 Side F 25 133567 Side G 25 Can t find what you re looking for? Call Brady Customer Service to find out more about custom solutions. Reverse Legend Options Reverse Side B Reverse Side F Reverse Side G 1-800-661-9983 461

Tags Spanish Tags B-837 - Heavy Duty Laminated Polyester tags meet OSHA s 50 Ib. pull force requirement for Tagout and have superior chemical resistance. These plastic tags are encapsulated in matte polyester laminate for superior durability. Nylon ties included. B-851 - Economy Polyester tags meet OSHA s 50 lb. pull force requirement for Tagout and have moderate chemical resistance. Nylon ties included. * Designates tags that have a self-adhesive, clear overlaminate flap which is pressed over the face of the tag for permanent protection. Designates tags that have a larger hole without a grommet to accommodate padlocks. B-853 - Cardstock tags provide an economical, yet durable material option. Attachment strings included. 98219 3 x5-3 4 B-851 10/pk 121514 3 x5-3 4 B-851* 10/pk 121515 5-1 5" x 3" B-837 25/pk 121516 5-3 4" x 3" B-851 25/pk 121517 5-3 4" x 3" B-853 25/pk 121518 5-1 5" x 3" B-837 25/pk 121519 5-3 4" x 3" B-851 25/pk 121520 5-3 4" x 3" B-853 25/pk Peel away liner Front Back Self-Laminating Photo Tags Include employee photos for easy identification and greater impact Constructed of durable B-851 polyester Available with or without 1 mil polyester overlay on front Includes nylon fasteners Size Qty. 65500 w/o Laminate 5-3 4 x 3 10 65501 w/ Laminate 5-3 4 x 3 10 96222 w/ Laminate 7 x 4 10 Tags w/ Detachable Key Stub Perforated heavy cardstock tag with detachable key stub Matching identification numbers printed on each part Accepts pencil, pen or marker Tie strings provided for easy tag attachment 1 -diameter metal ring provided for attaching stub to key Legend Size Qty. WKT2 Equipment Locked Out 5-3/4 x 3 25 WKT3 Do Not Operate 5-3/4 x 3 25 Padlock Tags Calendered vinyl accepts pencil, pen or marker Employs 3/8 metal grommet that fits over most padlock shackles Dimensions: 3 x 2 (grommet adds another 1 to height) Sold individually Legend Size Qty. 105722 Equipment Locked Out 105723 Do Not Operate 105724 Do Not Operate English/Spanish 3 x 2 plus grommet 3 x 2 plus grommet 3 x 2 plus grommet 1 1 1 462

Tags Two-Part Perforated Tags Two-part tags provide enhanced operational control and record-keeping. Stub is removed when tag is attached to a lockout point. Only the employee in possession of the stub has the authority to remove the tag. After the job is done, stub is returned to management for verification and monitoring of activity in the plant. Matching identification numbers are printed on each part. B-851 - Economy Polyester tags are durable 10 mil-thick polyester making it easy to remove chemicals, grease and grime. Suitable for indoor or outdoor use. Nylon ties included. B-853 - Cardstock tags provide an economical, yet durable material option. Attachement strings included. PLLT2 7-1/2 x 4 B-851 25/pk CLT2 7-1/2 x 4 B-853 25/pk PLLT4 7-1/2 x 4 B-851 25/pk CLT4 7-1/2 x 4 B-853 25/pk 1-Pocket Tag Holder Clear plastic holder is designed to hold 50 tags, ties and a marking pen (Tags and pen not included ) Comes with adhesive strips, magnetic strips, and screws for mounting Dimensions: 7-1/2 H x 4-1/2 W x 1-1/2 D TH2 1-Pocket Economy Tag Holder Pocket Premium Tag Center Acrylic center features 8 pockets for displaying and dispensing tags Each pocket holds up to 30 tags. Tags not included Four pre-drilled holes for wall mounting Dimensions: 15-3/4 H x 23-1/2 W x 2 D TC8 8-Pocket Premium Tag Center 10-Pocket Tag Safety Station Made of rugged polycarbonate Four pre-drilled holes for wall mounting Dimensions: 22 H x 16-1/2 W x 2-1/4 D Tags not included 81773 10-Pocket Tag Safety Station Tag Fasteners Three fastener styles available to meet every application Nylon fasteners meet OSHA requirements for attaching tagout devices Qty. 81760 12 26 Gauge Wire 100 81761 8 Reusable Beaded Ties 100 81762 8 Nylon Fasteners 100 Magnetic-Backed Protective Envelopes Transparent, durable vinyl construction makes it ideal for indoor or outdoor use Protects tags and data cards on machinery, valves, switches and more Size Qty. 81769 4-1 2 x 6-1 2 10 81770 5-1 2 x 8-1 2 10 Zip-Lock Protective Envelopes Transparent, durable vinyl construction makes it ideal for indoor or outdoor use Protects tags and data cards on machinery, valves, switches and more Size Qty. 81765 4-1 2 x 6-1 2 (w/o grommet) 10 81766 4-1 2 x 6-1 2 (w/grommet) 10 81767 5-1 2 x 8-1 2 (w/o grommet) 10 81768 5-1 2 x 8-1 2 (w/grommet) 10 1-800-661-9983 463

Padlocks Padlocks A written plan and comprehensive training program are foundational to a successful lockout tagout program. However, having the right tools for the job is extremely important, no matter what your industry is. Although padlocks may seem like a commonplace device, the durability and reliability of your padlocks is critical to your facility s safety. Brady provides a full line of padlocks that will withstand harsh environmental conditions, rough handling and the test of time. 3" Lock Body! Compact Safety Padlocks Safety Padlock with Steel Shackle Safety Padlock with Nylon Shackle Long-Body Safety Padlock Key Retaining Laminated Steel Padlocks Laminated Steel Padlocks Compact Aluminum Padlocks Full Aluminium Padlocks Compact & Lightweight - - - Non- - - - - Conductive Body & Keyway Most Corrosion Resistant Most Spark Resistant - - - - Most Tamperproof Most Rugged - - - - Body Height & Material 1-2/5" Fiberglass Reinforced Nylon 1-3/4" Fiberglass Reinforced Nylon 1-3/4" Fiberglass Reinforced Nylon 3" Fiberglass Reinforced Nylon 1-1/5" Steel 1-1/3" Steel 1-1/4" Aluminium 1-3/5" Aluminium Shackle Size & Material 3 16" dia. 1" high Aluminum 1 4" dia. 1-1/2" high Steel 1 4" dia. 1-1/2" high Nylon 1 4" dia. 1-1/2" high Steel 17 64" dia. 3/4", 2" or 3" high Steel 17 64" dia. 3/4" or 2" high Steel 1 4" dia. 1" high Aluminium 1 4" dia. 1", 1-1/2" or 3" high Aluminum Colors BK, BL, BR, GR, OR, PL, RD, YL, WT BK, BL, BR, GR, OR, PL, RD, YL, WT BK, BL, BR, GR, OR, PL, RD, YL, WT BK, BL, BR, GR, OR, PL, RD, YL, WT BK, BL, BR, GR, RD, PL, YL, WT BK, BL, BR, GR, OR, PL, RD, YL BK, BL, BR, GR, BK, BL, BR, GR, OR, PL, RD, SL, YL OR, PL, RD, SL, YL Identification Capabilities Key Possibilities *denotes custom Main Application Main Features Includes Engraving (front, back, left and right sides) Keyed Different Keyed Alike Electrical applications, small and confined spaces Non-conductive body, Compact & Light Weight, Key retaining system, Cylinder can support same keying system as regular safety padlock 1 Key & Labels (EN, FR, SP) Engraving (front, back, left and right sides) Keyed Different Keyed Alike Master Keyed* Grand Master Keyed* Industrial safety (process industry - custom applications) Engraving (front, back, left and right sides) Keyed Different Keyed Alike Master Keyed* Grand Master Keyed* Industrial safety (process industry - custom applications) Electrical applications Completely Non-conductive non-conductive body, Key retaining lock, Key retaining system, High system, High security (6-pins) security (6-pin) 1 Key & Labels (EN, FR, SP) 1 Key & Labels (EN, FR, SP) Engraving (front, back, left and right sides) Keyed Different Keyed Alike Master Keyed* Grand Master Keyed* Industrial safety (process industry - custom applications) Engraving (front, back, left and right sides) Keyed Different Keyed Alike Master Keyed* Grand Master Keyed* Industrial safety, Severe physical environment Physical Non-conductive resistance, Key body, Key retaining retaining system, system, High Superior corrosion security (6-pins) resistance 1 Key & Labels (EN, FR, SP) 1 key Labels Sold Seperately Engraving (front, back, left and right sides) Keyed Different Keyed Alike Master Keyed* Grand Master Keyed* Severe physical environment, Industrial safety Physical resistance, Superior corrosion resistance 2 keys Labels Sold Seperately Engraving (front, back, left and right sides) Keyed Different Keyed Alike Small space applications where light-weight and easy to carry locks are needed Compact & Lightweight, Superior corrosion resistance 2 keys Labels Sold Seperately Engraving (front, back, left and right sides) Keyed Different Keyed Alike Master Keyed* Grand Master Keyed* Outdoor, Industrial Safety, Food & Beverage applications (FDA approved lubricant in cylinder) Superior corrosion resistance, Laser engraving 2 keys Labels Sold Seperately 464

Padlocks OSHA Regulations 1910.147(c)(5) OSHA Device Requirements state that lockout devices must: Be provided by the employer Be standardized by size, shape or color Be distinguishable from locks used for other purposes. locks should only be used for lockout! Identify the individual who applied the lock (both tags and lock labels are acceptable for this purpose) Be capable of withstanding the usage environment and must be strong enough to prevent removal except by using excessive force with special tools, such as bolt cutters. Most importantly, whenever lockout devices are applied, they must remain under the exclusive control of the individual who attached them. No employee should be able to open a lock attached by someone else. Keying & Charting Options Keyed Different Keyed Alike Master and Grand Master Keyed Brady padlocks come keyed different when purchased from stock. This means that the key for one lock should not open another. Brady padlocks use 5- or 6-pin cylinders with keys precision machined to exacting standards. This enables us to offer a greater number of unique keys than other locks with the same number of pins, making it highly unlikely that you will ever receive a duplicate lock. When keyed alike, all locks in a set can be opened with the same key. This option is beneficial when multiple locks are assigned to a single employee. Remember, however, that under OSHA regulations no employee should be able to open a lock applied by someone else. Therefore, keyed alike locks from the same set should never be distributed to multiple employees. A master or grand master key can be used to open multiple locks that are keyed differently. This allows supervisors to easily remove a lock in the event of an emergency. In order for employees to retain exclusive control, master and grand master keys should be kept in a secure location that is accessible only to management. Key Charting Brady can track or chart your key codes upon request to simplify ordering replacement locks and to avoid duplicates when ordering additional locks. There is no extra charge for charting. Call for Customer Service at 1-800-661-9983 details! Need a Customized Solution? At Brady, we can help you with all of your custom lock needs. Brady customer service representatives are ready to answer your questions and get you started with: Custom Keying Logo and Text Engraving Serialization 11-800-661-9983 465

Safety Padlocks Brady Safety Padlocks Comply with all OSHA requirements and are a safer alternative to metal locks for lockout applications Nonconductive body with unique key cylinder prevents electricity from traveling from the shackle to the key, protecting workers when key is inserted Superior temperature, chemical and corrosion resistance Danger and Property of labels provided in English, Spanish and French and printed on 100% recycled paper Reserved paracentric keyway provides optimal security (prevents someone from getting a copy made at a local key shop) Key-retaining feature prevents key from being removed until shackle is securely closed Locks come keyed differently or in keyed-alike sets. Custom keying and charting available Lock bodies can be custom laser engraved upon request One key is supplied with each padlock for safer key management Actual size of Brady s Compact Safety Padlock Compact Safety Padlocks Extremely compact and lightweight - the smallest safety lock on the market Easily fits in small spaces - ideal for electrical contractors/ maintenance/electricians 5-pin cylinder can support same keying system as our current Safety Padlock Fiberglass reinforced nylon body for extra impact resistance Service temperature: 0 250 F (-20 120 C) Lock body dimensions: 1-2/5 H x 1-1/5 W x 5/8 D Shackle clearance: 1 ; shackle diameter 1/5 Each padlock includes 1 key and 1 each English, Spanish and French labels Safety Padlocks Lightweight, nonconductive and non-sparking body Special 6-pin cylinder resists tampering Fiberglass reinforced nylon body and triple-coated hardened steel shackle Service temperature: 0 250 F (-20 120 C) Lock body dimensions: 1-3/4 H x 1-1/2 W x 4/5 D Shackle clearance: 1-1/2 ; shackle diameter: 1/4 Each padlock includes 1 key and 1 each English, Spanish and French labels Compact Safety Padlocks - 1" Steel Shackle Keyed Different Keyed Different Keyed Alike Color 1/Pack 6/Pack 3/Pack Keyed Alike 6/Pack Red 143150 118926 118953 118954 Green 143152 118927 118955 118956 Orange 143154 118928 118957 118958 Blue 143156 118929 118959 118960 Yellow 143158 118930 118961 118962 Brown 143160 118931 118963 118964 White 143162 118932 118965 118966 Purple 143164 118933 118967 118968 Black 143166 118934 118969 118970 Safety Padlocks - 1-1/2 Steel Shackle Keyed Different Keyed Different Keyed Alike Color 1/Pack 6/Pack 3/Pack Keyed Alike 6/Pack Red 99552 51339 105886 105890 Green 99564 51345 105889 105893 Orange 99576 51347 123268 123270 Blue 99556 51344 105887 105891 Yellow 99570 51346 105888 105892 Brown 103033 101956 118947 118948 White 143123 118925 118949 118950 Purple 104919 104916 118951 118952 Black 99580 51353 123269 123271 When keyed alike, all locks in a set can be opened with the same key. This option is beneficial when multiple locks are assigned to a single employee. 466

Safety Padlocks Compact Safety Padlock Kits A great solution for any worker needing just one lock and one tag Ideal for electrical lockout points, tight spaces, storefront use or vending solutions Components: 1 - Compact Safety Padlock 1 - Heavy-duty Polyester (B-837) Tag with durable over-laminate that can be re-usable 1 - Nylon Cable Tie Compact Safety Padlock Kits Lock Color Qty 123143 Red 1 123144 Green 1 123145 Orange 1 123146 Blue 1 123147 Yellow 1 123148 Brown 1 123149 White 1 123150 Purple 1 123151 Black 1 3" Lock Body! Safety Padlocks with Non-Conductive Nylon Shackle Lightweight, nonconductive and non-sparking body Special 6-pin cylinder resists tampering Fiberglass reinforced nylon body with non-conductive nylon shackle Lock body dimensions: 1-3/4 H x 1-1/2 W x 4/5 D Shackle clearance: 1-1/2 ; shackle diameter: 1/4 Each padlock includes 1 key and one each English, Spanish and French labels Long Body Safety Padlocks 3 long body has ample space for your most important identification information Lightweight, nonconductive and non-sparking body Special 6-pin cylinder resists tampering Fiberglass reinforced nylon body and triple-coated hardened steel shackle Service temperature: 0 250 F (-20 120 C) Lock body dimensions: 3 H x 1-1/2 W x 4/5 D Shackle clearance: 1-1/2 ; shackle diameter: 1/4 Each padlock includes 1 key and one each English/Spanish and English/French labels Safety Padlocks - 1-1/2 Nylon Shackle Keyed Different Keyed Different Keyed Alike Color 1/Pack 6/Pack 3/Pack Keyed Alike 6/Pack Red 123324 123351 123333 123342 Green 123326 123353 123335 123344 Orange 123328 123355 123337 123346 Blue 123325 123352 123334 123343 Yellow 123327 123354 123336 123345 Brown 123330 123357 123339 123348 White 123332 123359 123341 123350 Purple 123331 123358 123340 123349 Black 123329 123356 123338 123347 Long Body Safety Padlocks - 1-1/2 Shackle Keyed Different Keyed Different Keyed Alike Color 1/Pack 6/Pack 3/Pack Keyed Alike 6/Pack Red 123405 123396 123414 123423 Green 123407 123398 123416 123425 Orange 123409 123400 123418 123427 Blue 123406 123397 123415 123424 Yellow 123408 123399 123417 123426 Brown 123411 123402 123420 123429 White 123413 123404 123422 123431 Purple 123412 123403 123421 123430 Black 123410 123401 123419 123428 When keyed alike, all locks in a set can be opened with the same key. This option is beneficial when multiple locks are assigned to a single employee. 1-800-661-9983 467

Steel Padlocks Key Retaining Laminated Steel Padlocks Key retaining safety feature prevents key from being removed until closed Reinforced laminated steel withstands severe physical abuse while hardened steel shackle resists tampering, cutting, prying, and rusting Body plates individually coated for superior rust protection 5-pin cylinder offers more unique key cuts, better tamper resistance than conventional 4-pin locks Colored bumpers supplied for identification (custom stamping available) Made from recycled material Each padlock includes 1 key. Custom keying and charting also available. Lock labels sold separately. Shackle clearance: 3/4, 2 or 3" Shackle diameter: 17/64 Lock body: 1-1/5 H x 1-5/16 W x 1 D Key Retaining Steel Padlocks 3/4 Shackle Color Keyed Different 1/Pack Keyed Different 6/Pack Red 143126 118935 Green 143128 118936 Blue 143130 118937 Yellow 143132 118938 White 143134 118939 Black 143136 118940 Brown 123272 123280 Purple 123273 123281 Key Retaining Steel Padlocks 2 Shackle Color Keyed Different 1/Pack Keyed Different 6/Pack Keyed Alike 3/Pack Keyed Alike 6/Pack Red 143144 118944 118977 118978 Green 143142 118943 118975 118976 Blue 143140 118942 118973 118974 Yellow 143148 118946 118981 118982 White 143146 118945 118979 118980 Black 143138 118941 118971 118972 Brown 123274 123282 123276 123278 Purple 123275 123283 123277 123279 Key Retaining Steel Padlocks 3 Shackle Color Keyed Different 1/Pack Keyed Different 6/Pack Keyed Alike 3/Pack Keyed Alike 6/Pack Red 123244 123236 123252 123260 Green 123245 123237 123253 123261 Blue 123246 123238 123254 123262 Yellow 123247 123239 123255 123263 White 123248 123240 123256 123264 Black 123249 123241 123257 123265 Brown 123250 123242 123258 123266 Purple 123251 123243 123259 123267 When keyed alike, all locks in a set can be opened with the same key. This option is beneficial when multiple locks are assigned to a single employee. Laminated Steel Padlocks Reinforced laminated steel withstands severe physical abuse while hardened steel shackle resists tampering Body plates individually coated for superior rust protection 5-pin cylinder offers more unique key cuts, better tamper resistance than conventional 4-pin locks Colored bumpers supplied for identification Each padlock includes 2 keys. Custom keying and charting also available. Lock labels sold separately. Shackle clearance: 3/4 or 2 Shackle diameter: 17/64 Lock body: 1-1/3 H x 19/16 W x 7/8 D Steel Padlocks - 3/4 Shackle Keyed Different Color 1/Pack Keyed Different 6/Pack Red 99500 51279 Blue 99504 51280 Green 99508 51281 Yellow 99512 51282 Orange 99516 51283 Black 99520 51284 Brown 101957 102696 Purple 104920 104917 Steel Padlocks - 2 Shackle Keyed Different Keyed Different Color 1/Pack 6/Pack Keyed Alike 3/Pack Keyed Alike 6/Pack Red 99524 51290 105894 105898 Blue 99528 51291 105895 105899 Green 99533 51292 105897 105901 Yellow 99539 51297 105896 105900 Orange 99543 51298 - - Black 99548 51299 - - Brown 101958 102698 - - Purple 104921 104918 - - When keyed alike, all locks in a set can be opened with the same key. This option is beneficial when multiple locks are assigned to a single employee. 468

Aluminum Padlocks Aluminum Padlocks Lightest-weight aluminum lock in the market and made from recycled material Aluminum shackle has superior spark and corrosion resistance Reserved paracentric keyway provides optimal security (prevents someone from getting a copy made at a local key shop) Anodized aluminum finish gives better fade resistance when used outdoors FDA approved lubricant in cylinder Shackle clearance: 1, 1-1/2 or 3" Shackle diameter: 1/4 Compact Lock body: 1-1/4"H x 1-1/4"W Compact Lock body features a 5-pin cylinder Regular Lock body: 1-3/5 H x 1-1/2 W x 3/4 D Regular Lock body features 6-pin cylinder which offers more unique key changes and better tamper resistance Each padlock includes 2 keys. Custom keying and charting also available. Lock labels sold separately. May we also suggest: Custom Keying Solutions At Brady, we can help you with your custom keying program. Just call a Brady customer service representative at 1-800-661-9983 to get started! Compact Aluminum - 1 Shackle Color Keyed Different 1/Pack Keyed Different 6/Pack Keyed Alike 3/Pack Keyed Alike 6/Pack Red 133270 133261 133279 133288 Blue 133271 133262 133280 133289 Green 133272 133263 133281 133290 Yellow 133273 133264 133282 133291 Orange 133274 133265 133283 133292 Black 133275 133266 133284 133293 Brown 133276 133267 133285 133294 Purple 133277 133268 133286 133295 Silver 133278 133269 133287 133296 When keyed alike, all locks in a set can be opened with the same key. This option is beneficial when multiple locks are assigned to a single employee. Aluminum Padlocks - 1 Shackle Color Keyed Different 1/Pack Keyed Different 6/Pack Red 99608 51360 Blue 99609 51361 Green 99610 51362 Yellow 99611 51363 Orange 99612 51368 Black 99613 51369 Brown 104574 104575 Purple 104572 104573 Silver 123320 123322 Combination Padlock Compact, lightweight lock with a steel shackle and a 4-digit resettable code 101963 Combination Padlock Aluminum Padlocks - 1-1/2 Shackle Color Keyed Different 1/Pack Keyed Different 6/Pack Keyed Alike 3/Pack Keyed Alike 6/Pack Red 99615 51370 105902 105882 Blue 99616 51371 105903 105883 Green 99617 51376 105881 105885 Yellow 99618 51377 105904 105884 Orange 99619 51378 123432 123437 Black 99620 50274 123433 123438 Brown 104578 104579 123434 123439 Purple 104576 104577 123435 123440 Silver 123321 123323 123436 123441 Aluminum Padlocks - 3 Shackle When keyed alike, all locks in a set can be opened with the same key. This option is beneficial when multiple locks are assigned to a single employee. Color Keyed Different 1/Pack Keyed Different 6/Pack Keyed Alike 3/Pack Keyed Alike 6/Pack Red 123293 123284 123302 123311 Blue 123294 123285 123303 123312 Green 123295 123286 123304 123313 Yellow 123296 123287 123305 123314 Orange 123297 123288 123306 123315 Black 123298 123289 123307 123316 Brown 123299 123290 123308 123317 Purple 123300 123291 123309 123318 Silver 123301 123292 123310 123319 1-800-661-9983 469

Padlock Labels Padlock labels are a great way to quickly identify padlocks used for lockout tagout. They help send a clear message to workers when a machine is down for service or maintenance. Steel Padlock Labels Durable B-826 vinyl labels include overlaminate strips Labels accept pencil, pen or marker Designed to fit Steel Padlocks Size Qty. 50280 English 3/4 H x 4-1/2 W 6 50281 Spanish 3/4 H x 4-1/2 W 6 50283 French 3/4 H x 4-1/2 W 6 Steel Padlock Label Durable B-7569 vinyl labels accept pencil, pen or marker Designed to fit Steel Padlocks Steel Padlock Label Durable B-7569 vinyl labels accept pencil, pen or marker Designed to fit Steel Padlocks Prinzing Labels Labels accept pencil, pen or marker Designed to fit Steel Padlocks Size Qty. 121448 3/4"H x 5"W 40 Size Qty. 121449 5/8"H x 4.5"W 5 Size Qty. LID-3 3/4"H x 4.5"W 25 Safety Padlock Labels Durable vinyl labels accept pencil, pen or marker Designed to fit Safety Padlocks Labels supplied with multiple languages Qty. 6 of each 51379 English/Spanish/French language Aluminum Padlock Labels Durable B-826 vinyl labels accept pencil, pen or marker Designed to fit Aluminum Padlocks Size Qty. 50289 English 0.8 H x 1.1 W 6 50292 Spanish 0.8 H x 1.1 W 6 50293 French 0.8 H x 1.1 W 6 Lock Label Overlaminate B-835 clear overlaminate protects existing lock label from dirt and grease Lock label sold separately Qty. 65508 1"H x 6"W overlaminate 40 470

Padlock Storage Padlock Stations Constructed of 14 gauge steel with red plastic coating Small station holds up to 4 padlocks (2-1/4 H x 3 W x 1-1/4 D) Large station holds up to 24 padlocks (3 H x 16 W x 1-1/4 D) LR060E LR360E Description Small Padlock Station Large Padlock Station Padlock Management System Reduces theft by controlling access to locks! Each lock is individually secured into a numbered port on the lock board Locks can only be removed by personnel with assigned access keys. Access key is retained in board until lock is returned. Call Brady Customer Service to place your order today! Enclosed Padlock Storage Modules Constructed of sintra with lockable, transparent acrylic doors Provides safe storage and controls access to padlocks Small module holds 16 locks (15 H x 15 W x 3-1 2 D) Large module hold 40 locks (30 H x 15 W x 3-1 2 D) * Padlocks Sold Separately. 65240 Small Padlock Storage Module 65241 Large Padlock Storage Module * Padlocks Sold Separately. Steel Padlock Control Centers Constructed of red powder-coated 22 gauge steel Each metal hook can hold 2 locks Two keys supplied for cabinet lock Small center holds 16 locks (10 H x 12 W x 2 D) Large center hold 32 locks (15-1 2 H x 18 W x 2 D) LR008E Small Padlock Control Center LR018E Large Padlock Control Center * Padlocks Sold Separately. Access Key Specify the following to order your management system: 1) LOCKS PER UNIT (Choose one) 5 locks (board size 5-3 8 H x 21-3 8 W x 4 D) 10 locks (board size 7 H x 21-3 8 W x 4 D) 15 locks (board size 10 H x 21-3 8 W x 4 D) 25 locks (board size 17-1 2 H x 21-3 8 W x 4 D) 50 locks (board size 32-1 2 H x 21-3 8 W x 4 D) 75 locks (board size 47-3 8 H x 21-3 8 W x 4 D) 2) COLOR OF LOCKS (Total must equal choice above) Yellow Qty Green Qty Red Qty 3) KEYING Keyed Alike Master Key w/ Keyed Alike Qty of Master Keys Keyed Different Master Key w/keyed Different Qty of Master Keys 4) COLOR OF ACCESS KEYS (Total must equal no. of locks) Yellow Qty Green Qty White Qty Blue Qty Red Qty Silver Qty (Other colors also available) * For Keyed Alike or Master Keyed Padlocks call your local Brady Distributor for pricing. This tracking system can also be used to secure a wide variety of plant assets, including employee issued tools, electronics and maintenance equipment. Specify the following to order ADDITIONAL LOCKS or access keys: 1) ADDITIONAL LOCKS Yellow Qty Green Qty White Qty Blue Qty Red Qty Silver Qty 2) KEYING Keyed Alike Master Key w/ Keyed Alike Qty of Master Keys Keyed Different Master Key w/keyed Different Qty of Master Keys 4) COLOR OF ACCESS KEYS (Total must equal no. of locks) Yellow Qty Green Qty White Qty Blue Qty Red Qty Silver Qty (Other colors also available) * For Keyed Alike or Master Keyed Padlocks call your local Brady Distributor for pricing. 1-800-661-9983 471

Group Boxes Boxes - A great idea for group lockout For group lockout situations involving a large number of workers and equipment, lock boxes can offer a number of advantages over hasps. How group lockout boxes work: Supervisor uses a single job lock on each energy control point to lock out equipment Keys for job locks are put in a lockout box Each worker applies his own lock to the lock box. As long as any one worker s lock remains on the lockout box, the keys to the job locks cannot be accessed, and the energy isolating devices cannot be operated. Each employee retains exclusive control, as required by OSHA. How group lockout boxes can save you money and increase efficiency: Example: Assume 5 workers need to lock out 10 energy control points Using hasps, 50 locks are required (all 5 workers must apply individual locks to each control point) Using a lockout box, only 15 locks are required (10 job locks applied to control points and 5 employee locks applied to lockout box). That s 70% fewer locks! Less weight hanging from the energy point - 1 lock instead of 5! Finally, checking the locks on the lock box allows you to track who is still working. With hasps, you need to walk around to each energy control point to see whose lock is still in place. NEW! SAFETY REDBOX Group Box Use as a portable or a mounted lockbox Quick release internal slide button allows lockbox to be carried to the point of need Can accommodate up to 12 padlocks Size: 6 H x 9 W x 3-1/2 D Color 145579 Mountable Lockbox Red 145580 Mountable Lockbox Yellow * Padlocks sold separately. Portable Metal Group Boxes Made of heavy duty steel, powdercoated for extra rust resistance 12 lock holes on lid, plus one lockable clasp on front Standard: 6 H x 9 W x 3-1/2 D Compartment holds up to 40 padlocks Extra large: 6 H x 7-3/8 W x 9-1/2 D Compartment holds up to 75 padlocks Size Color 45190 Standard-English 6 x 9 x 3-1/2 Blue 65672 Standard-English 6 x 9 x 3-1/2 Yellow 65699 Standard-English 6 x 9 x 3-1/2 Red 65040 Standard-Spanish 6 x 9 x 3-1/2 Red 51171 XLarge-English 6 x 7-3/8 x 9-1/2 Red * Padlocks Sold Separately. Combined Lock Storage / Group Box Made of heavy duty steel, powder coated for extra rust resistance Handy box features a lockable storage compartment and a group lockout compartment compartment has clear window with keyhole slot Standard Box:12-1/2 L x 7-1/2 W x 6 D Compartment: 8-1/2 L x 6 W x 6 D Compartment holds approx. 50 locks. 17 lock holes in group lock box lid Large box: 15 L x 101/2 W x 9 D Compartment: 10-1/2 L x 9 W x 9 D Compartment holds approx. 125 locks 34 lock holes in group lock box lid Size 105716 Standard 12-1/2 L x 7-1/2 W x 6 D 105717 Large 15 L x 10-1/2 W x 9 D * Padlocks Sold Separately. 472

Group Boxes Portable Plastic Group Box Durable plastic lockbox with transparent windows Excellent chemical and heat resistance Slot in front allows for keys to be inserted when box is locked Includes pre-drilled holes for easy wallmounting 12 interior hooks for hanging keys/locks Lock rails hold up to 16 padlocks Dimensions: 7-1/2 H x 8-1/2 W x 4-1/4 D Patent Applied For 50937 Portable Plastic Lock Box 50939 Extra Key Hooks (12/pkg) * Padlocks Sold Separately. Wall-Mounted Group Box Injection molded for extra durability Excellent chemical and heat resistance Slot in front allows keys to be inserted when locked Includes pre-drilled holes for easy wall-mounting 6 interior hooks for hanging keys/locks Lock rails hold up to 8 padlocks Dimensions: 6-1/5 H x 4 W x 5-1/2 D 50938 Miniature Wall Lock Box 50939 Extra Key Hooks (12/Pkg) * Padlocks Sold Separately. Acrylic Wall-Mounted Group Boxes Made of acrylic plastic with transparent front cover Includes pre-drilled holes for easy wall-mounting Pre-attached plastic hooks for hanging keys, tag stubs, etc. LG003E Small 6 x 6 x 2-1 2 LG008E Medium 7-1 2 x 12 x 2-1 2 GLOBOX Large 7-1 2 x 15-3 4 x 2-1 2 * Padlocks Sold Separately. Max. Locks 6 3 10 8 14 18 # Key Hooks Metal Wall-Mounted Group Boxes Made of durable, powder-coated steel with key slot on top Clear window slides out when locks are removed Comes with key pegs and ID labels to simplify key management Pre-drilled holes and hardware included for quick mounting Small lock box: 7 H x 8 W x 2-1/4 D 7 key pegs that hold 5 keys each 7 lock holes along bottom Large lock box: 7 H x 16 W x 2-1/4 D 15 key pegs that hold 5 keys each 12 lock holes along bottom 105714 Small Metal Lock Box 105715 Large Metal Lock Box * Padlocks Sold Separately. Portable / Wall Group Box Made of yellow powder-coated metal Accommodates 8-10 locks Can be used alone or in combination with Metal Cabinet Dimensions: 6 H x 15 W x 3 D LG252M Description Prinzing Metal Wall Lock Box SHOCK-STOP Group Box Combines lock box with storage board for hasps Lock box accommodates up to 6 locks and provides rail for storing locks Includes two SHOCK-STOP hasps, mounting hardware and instructions Dimensions: 16-1/2 H x 10-1/2 W x 2-1/2 D * Padlocks Sold Separately. 87692 Group Lock Box (w/2 hasps) 87693 Hasp (5/pkg,) * Padlocks Sold Separately. 1-800-661-9983 473

Hasps Steel Group Hasps Constructed of vinyl-coated high tensile steel w/ rust resistant plating Lock holes: 3 8 diameter Steel Group Hasps with Tabs Tamperproof interlocking tabs prevent unauthorized opening Case-hardened steel with rust proof plating and bright red vinyl insulation Lock holes: 3/8 diameter Corrosion-Resistant Group Hasps 12 gauge epoxy coated steel provides superior rust resistance and added dielectric strength Lock holes: 5 16 diameter Aluminum Economy Group Hasps Non-sparking, aluminum small hasps are a great addition to your tool box Lightweight at only 1-1/2 ounces Lock holes: 3/8 diameter Qty. 133161 1 Diameter Jaws 1 65375 1 Diameter Jaws 12 133162 1-1 2 Diameter Jaws 1 65376 1-1 2 Diameter Jaws 12 Qty. 105718 1 Diameter Jaws 1 105719 1-1 2 Diameter Jaws 1 Qty. T218 1 diameter jaws 1 T220 1-1/2 diameter 1 Qty. 105720 1 Diameter Jaws 1 105721 1-1 2 Diameter Jaws 1 Non-Conductive Group Hasps Strong, rigid plastic resin Excellent electrical insulating Performs at low temps, excellent heat resistance Heavy Duty Hasp Hasp allows multiple workers to lockout at each isolation point Stainless steel construction Accommodates up to 1/3" dia. padlock shackles Dual Jaw Hasp Dual construction allows for increased versatility in a single product Larger jaw measures 1.25" x 1.75" Smaller jaw measures 0.75" dia. Non-Conductive Nylon Group Hasp Accommodate up to 6 locks Withstands up to 1,000 lbs despite weighing only 1 oz. Dimensions: 7 H x 1-3 4 W Lock holes: 3 8 diameter Patent #7,124,606 Qty. LH220A Red Hasp 1 Qty. 871239 Heavy Duty Hasp 24 Qty. 236919 Dual Jaw Hasp 1 Qty. 99668 Nylon Hasp 1 Labeled Group Hasps Tough 5052 anodized aluminum alloy hasps include tamperproof locking tabs Write-on label accepts pencil, pen or marker. Pen and pencil markings are easily erased for repeated use Dimensions: 7-1 14 H x 3 W x 3 16 D Lock holes: 5 16 dia. Legend Option 1 Legend Option 2 Legend Option 3 Color Qty. 65960 Red 5 65961 Silver 5 65962 Blue 5 65963 Green 5 65964 Gold 5 65967 Combo* 5 Color Qty. 65970 Red 5 65971 Silver 5 65972 Blue 5 65973 Green 5 65974 Gold 5 65975 Combo* 5 *Combo includes 1 each of the five colors listed above. Color Qty. 39480 Red 5 474

Cable s Cable lockouts GREAT VERSATILITY! Cable lockouts provide a number of advantages. Because of their construction, cable lockouts can be used in a variety of applications locking out multiple disconnects and valves. They are also a great option for lockout of unusual energy isolating devices that cannot be effectively locked out by a traditional device. This versatility combined with ultimate portability makes cable lockout devices a great addition to any lockout tagout program. NEW! SAFELEX Universal Cable Original Cable Mini Cable Integrated hasp and cable provides simple way to lockout multiple energy isolation points Lightweight construction is great for handling, carrying and operation 145554 w/ 3 ft. steel cable 145553 w/ 6 ft. steel cable 145552 w/ 10 ft. steel cable 145551 w/ 15 ft. steel cable 145550 w/ 6 ft. non-conductive nylon cable 145549 w/ 10 ft. non-conductive nylon cable Brady s original cable lockout Device constructed of impact modified nylon, available in red, blue or yellow Includes 6 galvanized steel cable (1/8 outside dia.) Color 65318 Cable Device w/ 6 ft. cable Red 45191 Cable Device w/ 6 ft. cable Blue 45192 Cable Device w/ 6 ft. cable Yellow 65319 8 ft. steel cable only - 65320 10 ft. steel cable only - *Other cable lengths available upon request. Compact and portable with internally stored cable Push-button self-winding mechanism automatically cinches cable tight Superior chemical, corrosion and temperature resistant properties Includes either vinyl-coated steel cable or nonconductive nylon cable 6 lock holes accommodate most padlock shackles and hasps Body dimensions: 4 dia. x 1-3/4 deep Cable dimensions: 1/16 outside dia. x 8 length 50940 Mini Cable w/ Steel Cable 51442 Mini Cable w/ Nylon Cable Double Looped Cables Light weight and easier to spot, these 3/16" diameter cables are perfect for situations requiring a flexible lockout device and a visual deterrent ProLock Cable Spool All Purpose Cable Economical, highly visible alternative to chains. For additional ProLock products, visit BradyID.com Length Color Double Looped Cables 131063 Double Looped Cable 2ft Red 131064 Double Looped Cable 4ft Red 131065 Double Looped Cable 6ft Red 131066 Double Looped Cable 8ft Red ProLock Cable Spool 122265 ProLock Cable 164ft (50m) Green 122264 ProLock Cable 164ft (50m) Yellow 122263 ProLock Cable 164ft (50m) Red 122261 ProLock Cable 5ft (1.5m) Yellow 122262 ProLock Cable 5ft (1.5m) Green Superior chemical, corrosion and temperature resistance properties Available with interchangeable 3/16 dia. sheathed metal or 1/8 dia. non-conductive nylon cables Service temps of cables: Non-Conductive Nylon: -40 to 200 F Sheathed Metal: -30 to 180 F 50943 w/ 8 sheathed metal cable 50941 w/ 8 non-conductive nylon cable 50944 without cable 50947 8 Sheathed metal cable only 50950 12 Sheathed metal cable only 50953 16 Sheathed metal cable only 50956 20 Sheathed metal cable only 50945 8 Non-conductive nylon cable only 50948 12 Non-conductive nylon cable only 50951 16 Non-conductive nylon cable only 50954 20 Non-conductive nylon cable only Prinzing Economy Cable Unique lockout device accepts up to six 9/32 diameter padlocks Includes 6 or 10 plastic-coated steel cable Cable diameter: 3/16 Qty. CABLO Cable w/ 6 cable 1 CABLO-10 Cable w/10 cable 1 CABLE 6' Cable 1 CABLE-10FT 10' Cable 1 1-800-661-9983 475

Valve s Valve s From universal valve lockouts to adjustable gate valve lockouts, Brady offers a full line of devices to shut off all types of pressured valves. Gate valve lockout devices deny access and cover the valve handle. With Prinzing ball valve lockouts and Brady s standard, quarter-turn ball valve lockout devices, a comprehensive series of options are available from the global leader in lockout tagout solutions. Universal Valve Lock Out all Types of Valves with a Single Device Made of rugged industrial-grade steel and nylon for extra impact and chemical resistance Versatile open ended clamp fits over most closed rings, wide handles Can also lock out large levers, T handles, and other hard-to-secure mechanical devices Cable attachment offers choice of 1/8 nonconductive nylon or rustproof sheathed metal cable Small: for handle widths up to 1 (max handle thickness 0.6 ) Large: for handle widths up to 1.6 (max handle thickness 1.1 ) Patent No. 5,415,017 and 7,207,198 No need for multiple types and sizes of lockouts now one device does it all! Use blocking arm to lock out quarter-turn ball valves. Use cable attachment to lock out gate valves. Attach to butterfly handles to prevent trigger handle from being squeezed. Use two blocking arms to lock out 3-, 4- or 5-way valves, or to lock valves in the on, off, or throttled position. Complete Sets 51394 Small UVLO w/ 8 Sheathed Cable Attachment & Blocking Arm 51390 Small UVLO w/ 8 Nylon Cable Attachment & Blocking Arm 51392 Large UVLO w/ 8 Sheathed Cable Attachment & Blocking Arm 51388 Large UVLO w/ 8 Nylon Cable Attachment & Blocking Arm Individual Components 50924 Small UVLO Base Clamping Unit 50899 Large UVLO Base Clamping Unit 65402 Small Blocking Arm 65403 Large Blocking Arm 51395 Cable Attachment w/ 8-ft Sheathed Cable 50932 Cable Attachment w/ 8-ft Nylon Cable Other cable lengths also available. Butterfly Valve Innovative design to lock out butterfly valves with a lever handle in the OFF position Will accommodate handle thicknesses of: Small - 1/8 to 2-1/2 (3.2mm to 63.5mm) Large - 2 to 4 (50.8mm to 102mm) 121504 Butterfly Valve - Small 121505 Butterfly Valve Large Small Large 476

Valve s Plug Valve Ideal for difficult-to-secure plug valves in compliance with OSHA standards Four sizes to fit most 1 to 8 diameter manually-actuated plug valves Durable and tamper-resistant Service temps from -25 F to 200 F Compact in size and easy to use Adjustable Gate Valve Versatile lockout adjusts to fit 1 to 6-1/2 valve handles, replacing 3 conventional gate valve lockouts Constructed of rugged injectionmolded polypropylene Service temps from -13 F to 194 F Supplied with English, Spanish and French danger labels Gate Valve s Unique knockout center fits OS&Y or rising stem valves Made of rugged injection-molded polypropylene Service temps from 25 F to 200 F Accepts shackles up to 3/8 in dia. Supplied with English, Spanish and French danger labels 113231 for up to 7 8 Stem Dia. 113232 for 15 16 to1-3 8 Stem Dia. 113233 for 1-3 4 to 2-1 8 Stem Dia. 113234 for 2-3 16 to 2-1 2 Stem Dia. 64057 Adjustable Gate Valve Fits Valve Handles Dia. Red Yellow Green Blue 1 to 2-1 2 65560 65590 65595 65585 2-1 2 to 5 65561 65591 65596 65586 5 to 6-1 2 65562 65592 65597 65587 6-1 2 to 10 65563 65593 65598 65588 10 to 13 65564 65594 65599 65589 NEW! Prinzing Ball Valve Made from ultra-tuff polypropylene Small size locks out pipes 1/2 to 2-1/2 in diameter Small size can also lock valves OPEN on pipes from 1/2 to 1-1/4 in diameter Large size locks out pipes 2 to 8 in diameter Size Color BS07A-RD Small Red BS08A-RD Large Red BS07A-BU Small Blue BS08A-BU Large Blue BS07A-GN Small Green BS08A-GN Large Green BS07A-YW Small Yellow BS08A-YW Large Yellow Standard Ball Valve Easy to use, single-piece design locks quarter-turn ball valves in OFF position Two sizes fit most valves up to 3 65666 is made of super-tough nylon (service temp -40 to 248 F) 65692, 65669 and 65693 are made of powder-coated steel Max Valve Size Shackle / Pipe Dia. Dia. Max Handle Width Max Handle Thickness 65666 9 32 1 4 to 1 1-1 2 3 4 65692 3 8 1 4 to 1 1-1 2 3 4 65669 9 32 1-1 4 to 3 2-1 10 11 4 65693 3 8 1-1 4 to 3 1-9 10 11 4 Perma-Mount Ball Valve Retrofit devices stay permanently in place at the point of need One-time installation is easy to complete in just a few minutes Available in 2 sizes to fit a full range of 0.5" to 4" diameter ball valves Size 121540 Small Perma-Mount Ball Valve 121541 Large Perma-Mount Ball Valve 1-800-661-9983 477

Circuit Breaker Compatibility Guide Brand Model No. Poles Compatible Part # ABB E221 1 90844 ABB E222 2 90844 ABB E241 1 90844 ABB E242 2 90844 ABB E243 3 90844 ABB E244 4 90844 ABB E271 1 90844 ABB E272 2 90844 ABB E273 3 90844 ABB E274 4 90844 ABB F202AC 2 90850 ABB F204AC 4 90850 ABB F362 2 90844 ABB F364 4 90844 ABB F374 4 90844 ABB F672 2 90850 ABB F674 4 90850 ABB JS 2-3 65397 (w/cleat) ABB S1 3 65396 ABB S201-B 1 90844 ABB S201-C 1 90844 ABB S201-D 1 90844 ABB S201-K 1 90844 ABB S201P-K 1 90844 ABB S201P-Z 1 90844 ABB S201U-K 1 90844 ABB S201U-Z 1 90844 ABB S201UP-K 1 90844 ABB S201UP-Z 1 90844 ABB S202-B 2 90844 ABB S202-C 2 90844 ABB S202-D 2 90844 ABB S202-K 2 90844 ABB S202P-K 2 90844 ABB S202P-Z 2 90844 ABB S202U-K 2 90844 ABB S202U-Z 2 90844 ABB S202UP-K 2 90844 ABB S202UP-Z 2 90844 ABB S203-B 3 90844 ABB S203-C 3 90844 ABB S203-D 3 90844 ABB S203-K 3 90844 ABB S203P-K 3 90844 ABB S203P-Z 3 90844 ABB S203U-K 3 90844 ABB S203U-Z 3 90844 ABB S203UP-K 3 90844 ABB S203UP-Z 3 90844 ABB S204-B 4 90844 ABB S204-C 4 90844 ABB S204-K 4 90844 ABB S204U-K 4 90844 ABB S204U-Z 4 90844 ABB S204UP-K 4 90844 ABB S204UP-Z 4 90844 ABB S221 1 90844 ABB S222 2 90844 ABB S222-K 4 90844 Brady offers a wide variety of circuit breaker switch lockouts to isolate and secure most circuit breaker switches. From standard snap and clamp-on models to oversized, multi-pole and miniature options, Brady is sure to have what you need. Use the guide below to find the correct circuit breaker solution for your circuit breakers. Detailed product information can be found on the following pages. Brand Model No. Poles Compatible Part # ABB S223 3 90844 ABB S224 4 90844 ABB S251 1 90844 ABB S251 1 90844 ABB S252 2 90844 ABB S253 3 90844 ABB S261 1 90844 ABB S261-B 1 90844 ABB S261-C 1 90844 ABB S261-D 1 90844 ABB S262-B 2 90844 ABB S262-C 2 90844 ABB S262-D 2 90844 ABB S263 1 90844 ABB S263-B 3 90844 ABB S263-C 3 90844 ABB S263-D 3 90844 ABB S264-B 4 90844 ABB S264-C 4 90844 ABB S271-K 1 90844 ABB S272 1 90844 ABB S272-K 2 90844 ABB S273-K 3 90844 ABB S274-K 4 90844 ABB S281-K 1 90844 ABB S281-Z 1 90850 ABB S281UC-K 1 90844 ABB S281UC-Z 1 90850 ABB S282-K 2 90844 ABB S282-Z 2 90850 ABB S282UC-K 2 90844 ABB S282UC-Z 2 90850 ABB S283-K 3 90844 ABB S283-Z 3 90850 ABB S283UC-K 3 90844 ABB S283UC-Z 3 90850 ABB S3 3 65397 (w/cleat) ABB S501-B 1 90850 ABB S501-C 1 90850 ABB S501-D 1 90850 ABB S501-K 1 90850 ABB S501UC-B 1 90850 ABB S501UC-K 1 90850 ABB S502-B 2 90850 ABB S502-C 2 90850 ABB S502-D 2 90850 ABB S502-K 2 90850 ABB S502UC-B 2 90850 ABB S502UC-K 2 90850 ABB S503-B 3 90850 ABB S503-C 3 90850 ABB S503-D 3 90850 ABB S503-K 3 90850 ABB S503UC-B 3 90850 ABB S503UC-K 3 90850 ABB S504UC-B 4 90850 ABB S504UC-K 4 90850 AEG E82S 2 90847 Airpax Airpax 1 65396 (w/cleat) Brand Model No. Poles Compatible Part # Allen Bradley 1492-CB1DF 1 90844 Allen Bradley 1492-CB1DG 1 90844 Allen Bradley 1492-CB1DH 1 90844 Allen Bradley 1492-CB1F 1 90844 Allen Bradley 1492-CB1G 1 90844 Allen Bradley 1492-CB1H 1 90844 Allen Bradley 1492-CB2DF 2 90844 Allen Bradley 1492-CB2DG 2 90844 Allen Bradley 1492-CB2DH 2 90844 Allen Bradley 1492-CB2F 2 90844 Allen Bradley 1492-CB2G 2 90844 Allen Bradley 1492-CB2H 2 90844 Allen Bradley 1492-CB3F 3 90844 Allen Bradley 1492-CB3G 3 90844 Allen Bradley 1492-CB3H 3 90844 Allen-Bradley 1492-CB1 1 90844 Allen-Bradley 1492-CB2 2 90844 Allen-Bradley 1492-CB3 3 90844 American Ckt. Bkr. NEF 3 65396 (w/cleat) American Ckt. Bkr. NJJ 3 65397 (w/cleat), 65329 American Switch C 1 65396, 51252, 51254 Bryant BR 2-3 66321, 51254 Bryant BR 1 65387, 65396, 51254 Buschmat S46 1 90844 Challenger C 2-3 66321, 51254 Challenger C 1 65387, 65396, 51254 Challenger CDK 2-3 65397 Challenger LM 1 65396 Challenger NEJ 1-2 65396 (w/cleat), 51254 Clipsal 4CB 1-3 90844 Clipsal 4CB116 1 90844 Clipsal 4CB320 3 90844 CrouseHinds MP 2 66321, 51254 Cutler-Hammer BA 1 65396, 51254 Cutler-Hammer BAB 2-3 66321 Cutler-Hammer BAB 1 65387, 65396, 51254 Cutler-Hammer BD 1 65387, 65396, 51254 Cutler-Hammer BR 2-3 66321, 51254 Cutler-Hammer BR 1 65387, 65396, 51254 Cutler-Hammer BRH 2-3 66321, 51254 Cutler-Hammer BRH 1 65387, 65396, 51254 Cutler-Hammer BRHH 2 66321, 51254 Cutler-Hammer CC 3 65397 (w/cleat) Cutler-Hammer CH 2-3 66321, 51254 Cutler-Hammer CH 1 65387, 65396, 51252, 51254 Cutler-Hammer CH2 4 66321, 51254 Cutler-Hammer CHB 2-3 66321, 51254 Cutler-Hammer CHB 1 65387, 65396, 51252, 51254 Cutler-Hammer CHH 3 65396 (w/cleat) Cutler-Hammer CHKD 2-3 65397 Cutler-Hammer CHLD 2-4 65329 Cutler-Hammer CHMDL 2-3 65329 Cutler-Hammer CHND 2-4 65397 (w/cleat) Cutler-Hammer CHP 2-3 66321, 51254 Cutler-Hammer CHP 1 65387, 65396, 51252, 51254 478

Circuit Breaker Compatibility Guide (continued) Brand Model No. Poles Compatible Part # Cutler-Hammer CHQ 1 65396, 51254 Cutler-Hammer CHQ 2 66321, 51254 Cutler-Hammer CHSW 2-3 66321, 51254 Cutler-Hammer CKD 2-3 65397 Cutler-Hammer CL 1 65387, 65396, 51252, 51254 Cutler-Hammer CL 2 66321, 51254 Cutler-Hammer CLD 2-4 65329 Cutler-Hammer CLDC 2-4 65329 Cutler-Hammer CMDL 2-3 65329 Cutler-Hammer CND 2-4 65397 (w/cleat) Cutler-Hammer CNDC 2-4 65397 (w/cleat) Cutler-Hammer CSR 1 65396, 51254 Cutler-Hammer DK 2-3 65397 Cutler-Hammer E125B 1-4 65396, 51254 Cutler-Hammer E125E 1-4 65396, 51254 Cutler-Hammer E125H 1-4 65396, 51254 Cutler-Hammer E125S 1-4 65396, 51254 Cutler-Hammer ED 2-4 65396, 51254 Cutler-Hammer EDC 2-4 65396, 51254 Cutler-Hammer EDH 2-4 65396, 51254 Cutler-Hammer EFH 1-4 65396, 51254 Cutler-Hammer EGB 1-4 65396, 51254 Cutler-Hammer EGE 1-4 65396, 51254 Cutler-Hammer EGS 1-4 65396, 51254 Cutler-Hammer EHC 1-4 65396, 51254 Cutler-Hammer EHD 1-4 65396, 51254 Cutler-Hammer FB 2-3 65396, 51254 Cutler-Hammer FC 1-4 65396, 51254 Cutler-Hammer FD 1-4 65396, 51254 Cutler-Hammer FDB 2-4 65396, 51254 Cutler-Hammer FDC 2-4 65396, 51254 Cutler-Hammer FS 2-3 65396, 51254 Cutler-Hammer GB 1-3 65396, 51254 Cutler-Hammer GC 1-3 65396, 51254 Cutler-Hammer GD 1-3 65396, 51254 Cutler-Hammer GDB 1-3 65396, 51254 Cutler-Hammer GHB 1-3 65396, 51254 Cutler-Hammer GHBGFEP 1 65396, 51254 Cutler-Hammer GHC 1-3 65396, 51254 Cutler-Hammer GHCGFEP 1 65396, 51254 Cutler-Hammer HBAW 2-3 66321 Cutler-Hammer HBAW 1 65387, 65396, 51254 Cutler-Hammer HBAX 2-3 66321 Cutler-Hammer HBAX 1 65387, 65396, 51254 Cutler-Hammer HFD 1-4 65396, 51254 Cutler-Hammer HGHB 1 65396, 51254 Cutler-Hammer HGHC 1 65396, 51254 Cutler-Hammer HJD 2-4 65397 Cutler-Hammer HKD 2-4 65397 Cutler-Hammer HLD 2-4 65329 Cutler-Hammer HMCP 2-3 65396, 65397, 65329 Cutler-Hammer HMDL 2-3 65329 Cutler-Hammer HMDLB 2-3 65329 Cutler-Hammer HMPL 3 65397 (w/cleat), 65329 Cutler-Hammer HND 2-4 65397 (w/cleat) Cutler-Hammer HQP 2 66321 Cutler-Hammer HQP 1 65387, 65396, 51254 Brand Model No. Poles Compatible Part # Cutler-Hammer JD 2-4 65397 Cutler-Hammer JDB 2-3 65397 Cutler-Hammer JDC 2-4 65397 Cutler-Hammer KD 2-4 65397 Cutler-Hammer KDB 2-4 65397 Cutler-Hammer KDC 2-4 65397 Cutler-Hammer LA 2-3 65397 Cutler-Hammer LD 2-4 65329 Cutler-Hammer LDB 2-3 65329 Cutler-Hammer LDC 2-4 65329 Cutler-Hammer LH 3 65397 Cutler-Hammer LHB 3 65397 Cutler-Hammer LJ 3 51254 Cutler-Hammer MA 2-3 65397 (w/cleat) Cutler-Hammer MC 2-3 65397 (w/cleat) Cutler-Hammer MD 2-3 65329 Cutler-Hammer MDL 2-3 65329 Cutler-Hammer MDS 2-3 65329 Cutler-Hammer NB 2-3 65329 Cutler-Hammer ND 2-4 65397 (w/cleat) Cutler-Hammer NDC 2-4 65397 (w/cleat) Cutler-Hammer OPTIM 3 65397 (w/cleat) Cutler-Hammer PB 2-3 65329 Cutler-Hammer QBGF 1 65396 Cutler-Hammer QBGF 2 51254 Cutler-Hammer QBGFEP 1 65396 Cutler-Hammer QBGFEP 2 51254 Cutler-Hammer QBHGF 1 65396 Cutler-Hammer QBHGFEP 1 65396 Cutler-Hammer QBHW 2-3 66321 Cutler-Hammer QBHW 1 65387, 65396, 51254 Cutler-Hammer QC 2-3 66321, 51254 Cutler-Hammer QC 1 65387, 65396, 51254 Cutler-Hammer QCD 2-3 66321, 51254 Cutler-Hammer QCD 1 65387, 65396, 51254 Cutler-Hammer QCGF 1 65396 Cutler-Hammer QCGFEP 1 65396 Cutler-Hammer QCHGF 1 65396 Cutler-Hammer QCHGFEP 1 65396 Cutler-Hammer QCHW 2-3 66321, 51254 Cutler-Hammer QCHW 1 65387, 65396, 51254 Cutler-Hammer QHCW 2-3 66321, 51254 Cutler-Hammer QHCW 1 65387, 65396, 51254 Cutler-Hammer QHCX 2-3 66321, 51254 Cutler-Hammer QHCX 1 65387, 65396, 51254 Cutler-Hammer QHPW 2-3 66321 Cutler-Hammer QHPW 1 65387, 65396, 51254 Cutler-Hammer QHPX 2-3 66321 Cutler-Hammer QHPX 1 65387, 65396, 51254 Cutler-Hammer QPGF 1 65396 Cutler-Hammer QPGF 2 51254 Cutler-Hammer QPGFEP 1 65396 Cutler-Hammer QPGFEP 2 51254 Cutler-Hammer QPHGF 1 65396 Cutler-Hammer QPHGFEP 1 65396 Cutler-Hammer QPHW 2-3 66321 Cutler-Hammer QPHW 1 65387, 65396, 51254 Cutler-Hammer WME 1-3 90844 Brand Model No. Poles Compatible Part # Cutler-Hammer WMF 1-3 90844 Cutler-Hammer WMH 1-4 90844 Cutler-Hammer WMM 1-4 90844 Cutler-Hammer WMN 1-4 90844 Cutler-Hammer WMS 1-4 90844 E-T-A 911225 1 90847 E-T-A 911220G 2 90844 FAZ C16 1-4 90844 Fed. Pacific Elec. 2B 2 51254 Fed. Pacific Elec. BAB 1 65396, 51254 Fed. Pacific Elec. NA-single 3 65397 (w/cleat), 51254 Fed. Pacific Elec. NA-tie bar 2 51254 Fed. Pacific Elec. NB 1 65397 (w/cleat), 51254 Fed. Pacific Elec. NBH GFI 1 65396, 51254 Fed. Pacific Elec. NE/NEF 1-3 65396 (w/cleat) Fed. Pacific Elec. NEJ 1-3 65396 (w/cleat) Fed. Pacific Elec. NFJ 1-3 65396 Fed. Pacific Elec. NJJ 1-3 65397 Fed. Pacific Elec. NJL 1-3 65397 Fed. Pacific Elec. NM 1-3 65397 Fed. Pacific Elec. NP-single 1 65396, 51254 Frank Adams P 1 65396, 51254 FUJI Electric BU-ESA 3 65396 (w/cleat) FUJI Electric BU-ESB 3 65396 (w/cleat) FUJI Electric BU-FSB 3 65396 (w/cleat) FUJI Electric EA203B 3 65396 (w/cleat) FUJI Electric EA53B 3 65396 (w/cleat) GE Vynckier Series E 1-4 90847 GE Vynckier Series G 1-3 90847 General Electric EH400 3 65397 General Electric HQC 3 65396, 51254 General Electric SED 2-3 65396, 51254 General Electric SEH 2-3 65396, 51254 General Electric SEL 2-3 65396, 51254 General Electric SEP 2-3 65396, 51254 General Electric SFH 2-3 65396, 51254 General Electric SFL 2-3 65396, 51254 General Electric SFP 2-3 65396, 51254 General Electric SGD 2-3 65396 General Electric SGH 2-3 65396 General Electric SGL 2-3 65396 General Electric SGLA 2-3 65396 General Electric SGP 2-3 65396 General Electric SRPG 3 65396 General Electric TB 2 65396 (w/cleat), 51254 General Electric TBC 2 65396 (w/cleat), 51254 General Electric TE 1-3 65396 (w/cleat), 51254 General Electric TEB 1-3 65396 (w/cleat), 51254 General Electric TED 1-3 65396 (w/cleat), 51254 General Electric TEF 1-3 65396 (w/cleat), 51254 General Electric TEL 3 65396 (w/cleat), 51254 General Electric TEML 3 65396 (w/cleat), 51254 General Electric TEY 1-3 65396, 51254 General Electric TF 1-3 65396, 51254 General Electric TFC 3 65396 (w/cleat), 51254 General Electric TFJ 2-3 65397 General Electric TFK 2-3 65397 General Electric TFL 3 65397 Circuit Breaker s Legend Standard Circuit Breaker s EZ Panel Loc Miniature Circuit Breaker s 65387 120V Snap-On 65396 1120/277V Clamp-On 65397 480/600V Clamp-On 65329 480/600V Oversized 66321 Universal Multi-Pole 51252 Snap-On (SQD QO) 51254 Clamp-On (Universal) 90844 Pin-Out Standard 90847 Pin-In Standard 90850 Pin-Out Wide 90853 Tie-Bar 479

Circuit Breaker Compatibility Guide (continued) Brand Model No. Poles Compatible Part # General Electric THED 1-3 65396 (w/cleat), 51254 General Electric THEF 1-3 65396 (w/cleat), 51254 General Electric THFK 2-3 65397 General Electric THHQB 2-3 66321, 51254 General Electric THHQB-A 1 65387, 65396, 51254 General Electric THHQB-S 1 65396, 51254 General Electric THHQC 1-3 66321, 51254 General Electric THHQC-A 1 65387, 65396, 51254 General Electric THHQC-S 1 65396, 51254 General Electric THHQL 2-3 66321, 51254 General Electric THHQL-A 1 65387, 65396, 51254 General Electric THHQL-S 1 65396, 51254 General Electric THJK4 2-3 65397 (w/cleat) General Electric THJK6 2-3 65397 (w/cleat) General Electric THKM12 2-3 65329 General Electric THKM8 2-3 65329 General Electric THLC1 3 65396 (w/cleat) General Electric THQB 2-3 66321, 51254 General Electric THQB-A 1 65387, 65396, 51254 General Electric THQB-S 1 65396, 51254 General Electric THQC 2-3 66321, 51254 General Electric THQC-A 1 65387, 65396, 51254 General Electric THQC-AL 2-3 66321, 51254 General Electric THQC-S 1 65396, 51254 General Electric THQD 2-3 65396 (w/cleat), 51254 General Electric THQDBL 3 51254 General Electric THQL 2-3 66321, 51254 General Electric THQL-A 1 65387, 65396, 51254 General Electric THQL-S 1 65396, 51254 General Electric TJ2 2-3 65397 (w/cleat), 65329 General Electric TJ4 3 65397 General Electric TJC 2-3 65396 (w/cleat), 51254 General Electric TJD 2-3 65397 (w/cleat) General Electric TJJ 2-3 65397 (w/cleat) General Electric TJK 2-3 65397 (w/cleat) General Electric TJS 2-3 65397 (w/cleat) General Electric TK4V 3 65397 General Electric TKC 3 65396 (w/cleat), 51254 General Electric TKM 2-3 65329 General Electric TKMA8 3 65329 General Electric TQB 2-3 66321, 51254 General Electric TQB-A 1 65387, 65396, 51254 General Electric TQB-S 1 65396, 51254 General Electric TQC 2-3 66321, 51254 General Electric TQC-A 1 65387, 65396, 51254 General Electric TQC-S 1 65396, 51254 General Electric TQD 2-3 65396 General Electric TQL-A 1 65387, 65396, 51254 General Electric TQL-S 1 65396, 51254 General Electric V 1-3 90847 General Electric V 1-4 90847 Hager 453717 3 90844 Hager MW216A 2 90844 Hager MW620A 4 90844 Heinemann LB 1 65396 (w/cleat) Heinemann LF 1 65396 (w/cleat) Heinemann LJ 1 65396 (w/cleat) Kapp LS68 1 90844 Legrand 1908 1 90844 Legrand 1935 3 90844 Legrand 1980 3-4 90844 Legrand 4302 2 90847 Legrand 6469 3 90847 Lemag SD62 1 65396 Merlin Gerin B100A 2 90850, 90853 Merlin Gerin B100A 2 90850, 90853 Merlin Gerin C1251N 3 65329 Merlin Gerin C32N 1-3 90844 Merlin Gerin C45AD 3 90844 Merlin Gerin C60a 1-4 90844 Merlin Gerin C60H 1-4 90844 Merlin Gerin C60N 1-4 90844 Merlin Gerin C801N 3 65329 Merlin Gerin C80A 3 90850, 90853 Brand Model No. Poles Compatible Part # Merlin Gerin C80A 3 90850, 90853 Merlin Gerin CE104N 3 65396 (w/cleat) Merlin Gerin CJ 3 65397 (w/cleat) Merlin Gerin CK1200NA 3 65329 Merlin Gerin NC100H 1-3 90850 Merlin Gerin NC100L 1-4 90850 Merlin Gerin NC100L MA 3 90850 Merlin Gerin NC100LH 1-4 90850 Merlin Gerin NC100N 1-4 90850 Merlin Gerin NC125H 1-3 90850 Proteus C6 1 90844 Proteus AC22BS5419 2 66321 Proteus BSEN60947-3 2 66321 Proteus C16 1 90844 Proteus C6 1-3 90844 Siemans ITE 5SN22 2 90853 Siemans ITE 5SQ11 1 90850 Siemans ITE 5SQ12 2 90853 Siemans ITE 5SQ13 3 90853 Siemans ITE 5SQ16 4 4 90853 Siemans ITE 5SX11 1 90850 Siemans ITE 5SX12 2 90853 Siemans ITE 5SX13 3 90853 Siemans ITE 5SX21 1 90850 Siemans ITE BL 1 65387, 65396, 51252, 51254 Siemans ITE BL 2-3 66321, 51254 Siemans ITE BLF-GFI 2 66321, 51254 Siemans ITE BLH 1 65387, 65396, 51254 Siemans ITE BLH 2-3 66321, 51254 Siemans ITE BQ 1 65387, 65396, 51254 Siemans ITE BQ 2-3 66321, 51254 Siemans ITE BQCH 1-3 65396, 51254 Siemans ITE BQD 1-3 65396, 51254 Siemans ITE BQH 1 65387, 65396, 51254 Siemans ITE BQH 2-3 66321, 51254 Siemans ITE CED6 2-3 65396, 51254 Siemans ITE CFD6 2-3 65397 (w/cleat) Siemans ITE CFD6-ETI 2-3 65397 (w/cleat) Siemans ITE CJ3 3 65397 Siemans ITE CJD6 2-3 65397 Siemans ITE CJD6-ETI 2-3 65397 Siemans ITE CLF 2 65397 Siemans ITE CMD6 3 65329 Siemans ITE CMD6-ETI 3 65329 Siemans ITE CND6 3 65329 Siemans ITE CPD6 3 65329 Siemans ITE CQD 1-3 65396 (w/cleat), 51254 Siemans ITE E2 1-3 65396, 51254 Siemans ITE E4 1-3 65396, 51254 Siemans ITE ED 1-3 65396, 51254 Siemans ITE ED4 1-3 65396, 51254 Siemans ITE ED6 1-3 65396, 51254 Siemans ITE ED6-ETI 3 65396, 51254 Siemans ITE EE3 3 65396 (w/cleat), 51254 Siemans ITE EH3 3 65396 (w/cleat), 51254 Siemans ITE EQP 4 66321, 51254 Siemans ITE ET 3 65396 (w/cleat), 51254 Siemans ITE FD6A 2-3 65397 (w/cleat) Siemans ITE FJ2-B 2-3 65396 (w/cleat), 65397 (w/cleat) Siemans ITE FJ3 2 65397 Siemans ITE FJ6 2 65397 (w/cleat) Siemans ITE FXD6-ETI 2-3 65397 (w/cleat) Siemans ITE FXD6A 2-3 65397 (w/cleat) Siemans ITE GF 1 65396, 51254 Siemans ITE HBL 1 65387, 65396, 51254 Siemans ITE HBL 2-3 66321, 51254 Siemans ITE HBQ 1 65387, 65396, 51254 Siemans ITE HBQ 2-3 66321, 51254 Siemans ITE HE4 1-3 65396, 51254 Siemans ITE HED4 1-3 65396, 51254 Siemans ITE HED6 2-3 65396, 51254 Siemans ITE HFD6 2-3 65397 (w/cleat) Siemans ITE HFXD6 2-3 65397 (w/cleat) Brand Model No. Poles Compatible Part # Siemans ITE HHED6 2-3 65396, 51254 Siemans ITE HHFD6 2-3 65397 (w/cleat) Siemans ITE HHJD6 2-3 65397 Siemans ITE HHJXD6 2-3 65397 Siemans ITE HJD6 2-3 65397 Siemans ITE HJXD6 2-3 65397 Siemans ITE HMD6 2-3 65329 Siemans ITE HMXD6 2-3 65329 Siemans ITE HN3 2 65329 Siemans ITE HND6 2-3 65329 Siemans ITE HNXD6 2-3 65329 Siemans ITE HPD6 3 65329 Siemans ITE HPXD6 3 65329 Siemans ITE HQJ2-H 3 65396, 51254 Siemans ITE HQP 1 65387, 65396, 51254 Siemans ITE HQP 2-3 66321, 51254 Siemans ITE HQPP 1 65387, 65396, 51254 Siemans ITE HQPP 2-3 66321, 51254 Siemans ITE HQPPH 2 66321, 51254 Siemans ITE HRD6 3 65329 Siemans ITE HRXD6 3 65329 Siemans ITE JD2 3 65329 Siemans ITE JD6-A 2-3 65397 Siemans ITE JJ3 3 65397 Siemans ITE JJ6 3 65329 Siemans ITE JL3 3 65397 Siemans ITE JXD2-A 2-3 65397 Siemans ITE JXD6-A 2-3 65329 Siemans ITE KM3 3 65329 Siemans ITE LL3 3 65397 Siemans ITE LL6 3 65329 Siemans ITE LXD6-ETI 3 65329 Siemans ITE MD6 2-3 65329 Siemans ITE MXD6 2-3 65329 Siemans ITE MXD6-ETI 2-3 65329 Siemans ITE ND6 2-3 65329 Siemans ITE NXD6 2-3 65329 Siemans ITE PD6 3 65329 Siemans ITE PXD6 3 65329 Siemans ITE QJ2 2-3 65396 (w/cleat), 51254 Siemans ITE QJ2-H 2-3 65396 (w/cleat), 51254 Siemans ITE QJH2 2-3 65396 (w/cleat), 51254 Siemans ITE QP 1 65387, 65396, 51254 Siemans ITE QP 2-3 66321, 51254 Siemans ITE QP1 1 65396, 51254 Siemans ITE QPH 1 65387, 65396, 51254 Siemans ITE QPH 2-4 66321, 51254 Siemans ITE QPP 1 65387, 65396, 51254 Siemans ITE QPP 2-3 66321, 51254 Siemans ITE QPPH 1 65387, 65396, 51254 Siemans ITE QPPH 2-3 66321, 51254 Siemans ITE RD6 3 65329 Siemans ITE RXD6 3 65329 Siemans ITE SCMD6 3 65329 Siemans ITE SCND6 3 65329 Siemans ITE SHLD6-A 3 65329 Siemans ITE SHMD6 3 65329 Siemans ITE SHND6 3 65329 Siemans ITE SHPD6 3 65329 Siemans ITE SMD6 3 65329 Siemans ITE SND6 3 65329 Siemans ITE SPD6 3 65329 Siemans ITE VF3 3 65396 Siemens 17U 5SQ16 4 90853 Siemens C10 5SX1 1 90850 Siemens C32 5SX1-2 2 90853 Siemens L20A 5SN2-2 2 90853 Square D EDB 1-3 65396, 51254 Square D EGB 1-3 65396, 51254 Square D EH4 1-3 65396, 51254 Square D EHB 1-3 65396, 51254 Square D EHB 2-3 66321, 51254 Square D EJB 1-3 65396, 51254 Square D EZ 3 65329 480

Circuit Breaker Compatibility Guide (continued) Brand Model No. Poles Compatible Part # Square D FA 1-3 65396 (w/cleat) Square D FAL 1-3 65396 (w/cleat) Square D FC 3 65396 (w/cleat) Square D FCL 2-3 65396 (w/cleat) Square D FDA 2-3 65396, 51254 Square D FGA 3 51254 Square D FH 1-3 65396 (w/cleat) Square D FHL 1-3 65396 (w/cleat) Square D FHL-DC 3 65396 (w/cleat) Square D FHP 3 65396 (w/cleat) Square D FI 3 65396 (w/cleat) Square D FIL 3 65396 (w/cleat) Square D FY 1 65396 (w/cleat) Square D GJL 3 65396 (w/cleat) Square D KA 2-3 65396 (w/cleat) Square D KAL 2-3 65396 (w/cleat) Square D KAP 2-3 65397 Square D KC 2-3 65396 (w/cleat) Square D KCL 2-3 65396 (w/cleat) Square D KH 2-3 65396 (w/cleat) Square D KHL 3 65396 (w/cleat) Square D KI 2-3 65396 (w/cleat) Square D KIL 2-3 65396 (w/cleat) Square D L2 3 65329 Square D LA 2-3 65397 (w/cleat) Square D LAL 2-3 65397 (w/cleat), 65329 Square D LAP 3 65397 (w/cleat), 65329 Square D LC 3 65329 Square D LCP 3 65329 Square D LH 2-3 65397 (w/cleat) Square D LHL 3 65397 (w/cleat), 65329 Square D LHP 1-2 65397 (w/cleat), 65329 Square D LXL 3 65329 Square D MA 3 65329 Square D MA 2-3 65397 (w/cleat) Square D MAL 3 65329 Square D MH 2-3 65329 Square D MH 2-3 65397 (w/cleat) Square D MHL 2-3 65329 Square D ML-1 3 65397 (w/cleat) Square D ML-3 3 65329 Square D MXL 3 65329 Square D Q1B 2-3 65396, 51254 Square D Q1L 2-3 65396, 51254 Square D Q2 2-3 65396 (w/cleat) Square D Q2H 2-3 65396 (w/cleat) Square D Q2L 2-3 65396 (w/cleat) Square D Q2MT 2-3 65396 (w/cleat) Square D Q4 2-3 65397 (w/cleat) Square D Q4L 2-3 65397 (w/cleat) Square D QO 1 51252 Square D QO 2-3 65387, 65396, 51252, 51254 Square D QO-H 2 51252 Square D QO-SWN 2-3 65387, 65396, 51252, 51254 Square D QO-VH 1 51252 Brand Model No. Poles Compatible Part # Square D QO-VH 2-3 65387, 65396, 51252, 51254 Square D QOB 1 51252 Square D QOB 2-3 65387, 65396, 51252, 51254 Square D QOB-H 2 51252 Square D QOB-VH 2-3 66321 Square D QOB-VH 1 65387, 65396, 51252, 51254 Square D QOM1-VH 2 65396, 51254 Square D QOM2-VH 2 65396, 51254 Square D QOU 1 51252 Square D QOU 2-3 65396, 51252, 51254 Square D QOU w/tie bar 2-3 66321, 51254 Square D QYU 1 51252 Square D Y1 1 65397 Sursum EA53 3 90847 Sylvania GTE QC 2 66321, 51254 Sylvania GTE Type C 2 66321, 51254 Thomas & Betts F Frame 1-3 65396, 51254 Toshiba E225B 3 65396 (w/cleat) Westinghouse BA 1-3 65387, 65396, 51254 Westinghouse BA w/tie bar 2-3 66321 Westinghouse BAB 1-3 65387, 65396, 51254 Westinghouse BR 1-3 65387, 65396, 51254 Westinghouse BR w/tie bar 2-3 66321, 51254 Westinghouse BRH w/tie bar 2-3 66321 Westinghouse CA 2 65396 (w/cleat) Westinghouse DA 2-3 65397 Westinghouse DK 3 65397 Westinghouse EB 1-3 65396 (w/cleat), 51254 Westinghouse ED 2-3 65396, 51254 Westinghouse EH 1-3 65396, 51254 Westinghouse EHB 1-3 65396 (w/cleat) Westinghouse EHD 1-3 65396, 51254 Westinghouse FA 3 65396 (w/cleat), 51254 Westinghouse FB 2-3 65396 (w/cleat), 51254 Westinghouse FD 1-4 65396, 51254 Westinghouse FDB 2-4 65396, 51254 Westinghouse FDC 2-4 65396, 51254 Westinghouse FP 3 65397 (w/cleat) Westinghouse GB 1-3 65396, 51254 Westinghouse GBH 1-3 65396, 51254 Westinghouse GHB 1-3 65396, 51254 Westinghouse GR 3 65397 Westinghouse HBAW 1 65387, 65396, 51254 Westinghouse HBAX 1 65387, 65396, 51254 Westinghouse HCA 3 65396 (w/cleat) Westinghouse HFB 1-3 65396 (w/cleat) Westinghouse HFD 1-4 65396, 51254 Westinghouse HKD 3 65397 Westinghouse HLA 3 65397 Westinghouse HLB 2-3 65397 Westinghouse HMC 3 65397 Westinghouse HMCP 3 65396 (w/cleat), 51254 Westinghouse HNC 3 65329 Brand Model No. Poles Compatible Part # Westinghouse HQNP 3 65396, 51254 Westinghouse HQP 1 65387, 65396, 51254 Westinghouse JA 2-3 65397 Westinghouse JB 3 65397 Westinghouse JD 2-4 65397 Westinghouse JDB 3 65397 Westinghouse KA 3 65397 (w/cleat) Westinghouse KB 2-3 65397 Westinghouse LA 3 65397 (w/cleat) Westinghouse LB 3 65397 Westinghouse LBB 3 65397 Westinghouse LH 3 65397 Westinghouse MA 2-3 65397 (w/cleat) Westinghouse MC 2-3 65397 (w/cleat) Westinghouse MCC 2-3 65397 (w/cleat) Westinghouse MCPO 3 65396 (w/cleat), 51254 Westinghouse NB 2-3 65329 Westinghouse P 3 65396, 51254 Westinghouse QBHW 1 65387, 65396, 51254 Westinghouse QC 3 66321 Westinghouse QC 1 65387, 65396, 51254 Westinghouse QCHQ 1 65387, 65396, 51254 Westinghouse QHCW 1 65387, 65396, 51254 Westinghouse QHCX 1 65387, 65396, 51254 Westinghouse QHPW 1 65387, 65396, 51254 Westinghouse QPHW 1 65387, 65396, 51254 Westinghouse Quicklag P 1-3 65396, 51254 Westinghouse RE 1-2 65396, 51254 Westinghouse RH 3 65397 Westinghouse WPHX 1 65387, 65396, 51254 Wylex WRS40/2 2 90844 Zinsco HQB 3 65396, 51254 Zinsco QB 1 65396, 51254 Circuit Breaker s Legend Standard Circuit Breaker s EZ Panel Loc Miniature Circuit Breaker s 65387 120V Snap-On 65396 1120/277V Clamp-On 65397 480/600V Clamp-On 65329 480/600V Oversized 66321 Universal Multi-Pole 51252 Snap-On (SQD QO) 51254 Clamp-On (Universal) 90844 Pin-Out Standard 90847 Pin-In Standard 90850 Pin-Out Wide 90853 Tie-Bar 481

Circuit Breaker EZ Panel Loc System Works on wide range of breakers, including single- and multi-pole configurations Can be used with most padlocks by making use of unique lock rail system Allows panel door to be closed even when lockouts are in place Accommodates multiple locks, facilitating group lockout activity without hasps Keeps weight off the breakers, protecting delicate electrical components from damage Positions locks and tags outside the panel, making sure lockout activity is clearly visible to anyone in the area Patent No. 6,727,441 (Not recommended for use with multilock hasps) device is unlocked by inserting and turning the black plastic key. How EZ Panel Loc System Works 1. Expose the super-bond adhesive on back of rail. Permanently affix to any location on the panel. 2. Attach the lockout device to the breaker and snap into locked position. Technical Information devices constructed of high-impact Isoplast polymers Cables are 2-ft. in length Lock rails made of durable isoplast polymers with acrylic adhesive backing Lock rails available in 4 or 8 lengths (with 7 or 15 lock loops) SNAP-ON For use on Square D NQO and other breakers that have a hole in the switch tongue. Just align pins with hole and snap closed. Pins prevent switch from being thrown. 3. Pass plastic key through lock rail and attach lock, preventing key from sliding down cable and opening lockout device. Covers Most 120V 277V Breakers! The EZ Panel Loc System comes in two different styles, accommodating an exceptionally wide range of breaker models. CLAMP-ON For use on breakers that do not have a hole in the switch tongue. Turn thumbscrew to clamp lockout securely onto switch, then snap the cover closed to prevent thumbwheel from being loosened. 4. For group lockouts, run key through multiple loops in lock rail and apply locks. No hasps required! (Not recommended for use with multilock hasps) 5. Low-profile lockouts allow panel doors to be closed on most breaker panels. EZ Panel Loc Accessories Outer Dimensions (in.) Switch Clearance (in.) A B C D E Snap-On Style 0.90 1.88 0.74 0.40 0.35 Clamp-On Style 0.95 2.56 0.74 0.35 0.42 Description 1 Per Pkg 6 Per Pkg Snap-On Device 51252 65815 Clamp-On Device 51254 65810 4 Lock Rail 51256 65814 8 Lock Rail 51258 51260 Spacing Gasket For low profile panels, gasket pushes out the panel frame adding an additional 3/8 of clearance between the panel and the door Easy install with self-adhesive backing Dimensions: 3/8 D x 1 W x 15 L 89256 EZ Panel Loc Spacing Gasket 482

Circuit Breaker 120V Snap-On Breaker Designed for 120V breakers with holes in the switch tongue Quick and easy just snap in place and apply lock! Dual cavities accommodate different size switch tongues Accepts lock shackles up to 9/32 dia. Dimensions: 0.83 H x 0.35 W x 2.15 L Clamp-On Breaker Extremely versatile works on a wide range of single-pole and internal-trip multi-pole breakers! Use thumbscrew to clamp lockout onto switch tongue, then pull cover over thumbscrew and lock in place to prevent clamp from being loosened Accepts lock shackles up to 9/32 dia. Included detachable cleats expand the range of applicable breakers Universal Multi-Pole Breaker Single device works with most major multi-pole breakers that employ a tie-bar Made of durable impact-modified nylon Compatible with GE, ITE, Sylvania, Challenger, Bryant, Westinghouse, General Switch Co., and more! Use thumbscrew to clamp lockout securely over tie bar, then insert lock to prevent clamp from being loosened Qty. Qty. Patent No. 5,300,740 65387 65688 120V Snap-On Circuit Breaker 120V Snap-On Circuit Breaker s 1 6 65396 120/277V Clamp-On 1 65965 120/277V Clamp-On 6 65397 480/600V Clamp-On 1 65966 480/600V Clamp-On 6 65404 Extra Cleats For 120/277V 6 65406 Extra Cleats For 480/600V 6 Qty. 66321 Universal Multi-Pole Breaker 1 66320 Universal Multi-Pole Breaker s 6 Five Steps to Compliance Whitepaper Download this whitepaper to get started on a 5 step plan that will help you comply with OSHA s /Tagout regulations and keep your employees safe. Oversized Clamp On Breaker Oversized 480/600V frame lockout fits breaker switches up to 2-1/4 wide and 7/8 thick Made of durable polypropylene and glass filled-impact-modified nylon 480-600V Breaker Blocker Ideal for oversized and irregularly shaped switches Self-adhesive backed rails are permanently installed onto an electrical panel simply clean panel surface and adhere no drilling required! Download now at: BradyID.com/5steps Patent No. 5,500,495 Blocking Bars are 7-1/2 long Red blocking bar indicates locked off, green bar indicates locked on Qty. Qty. 65329 Oversized Breaker 1 65321 Oversized Breaker 6 90892 7.6 Red Blocking Bar 5 90893 7.6 Green Blocking Bar 5 51264 4 Yellow Mounting Rails 2 51265 Blocking Bar Holder 5 90891 Breaker Block Kit* 1 *Kit includes 2 yellow mounting rails, 1 red blocking bar, 1 green blocking bar and 3 alcohol wipes. 483

Circuit Breaker Miniature Circuit Breaker s A safe and effective method for locking out miniature circuit breakers, commonly used in European and Asian equipment NO TOOLS required for installation! The is easily installed with a push button. Tie Bar style lockouts have a convenient thumb wheel for quick application.. Available for single and multi-pole breakers Lock with Brady Safety Padlocks (not included). Devices can support padlocks with a shackle diameter up to 9/32 Material: Glass-filled nylon 4 Different types: POS - Pin Out Standard PIS - Pin In Standard POW - Pin Out Wide TBLO - Tie Bar Pin-Out Standard (POS) Pin-In Standard (PIS) Type Qty. 90844 POS - Pin Out Standard 1 90845 POS - Pin Out Standard 6 90847 PIS - Pin In Standard 1 90848 PIS - Pin In Standard 6 90850 POW - Pin Out Wide 1 90851 POW - Pin Out Wide 6 90853 TBLO - Tie Bar 1 90854 TBLO - Tie Bar 6 Pin-Out Wide (POW) Tie-Bar (TBLO) Miniature Circuit Breaker Compatibility Chart Brand Poles Model No. Type (1/pkg) ABB 1 S222 POS 90844 ABB 1 F374 POS 90844 ABB 1 S251, S261, S263 POS 90844 ABB 1 S272, S253 POS 90844 ABB 3 S253 POS 90844 AEG 2 E82S PIS 90847 Allen-Bradley 1,2,3 1492-CB1, 2, 3 POS 90844 Buschmat 1 S46 POS 90844 Clipsal 1 4CB116 POS 90844 Clipsal 3 4CB320 POS 90844 E-T-A 1 911225 PIS 90847 E-T-A 2 911220G POS 90844 FAZ 4 C16 POS 90844 FAZ 1 C16 POS 90844 GE Vynckier 3 Series E PIS 90847 GE Vynckier 3 Series G PIS 90847 GE Vynckier 4 Series E PIS 90847 GE Vynckier 1 Series G PIS 90847 GE Vynckier 16A 2 Series E PIS 90847 GE Vynckier C16, 16A 1 Series E PIS 90847 Hager 3 453717 POS 90844 Hager 2 MW216A POS 90844 Hager 4 MW620A POS 90844 Kapp 1 LS68 PIS 90844 Legrand 2 1935 TBLO 90844 Legrand 3 1980 TBLO 90844 Brand Poles Model No. Type (1/pkg) Legrand 4 1980 TBLO 90844 Legrand 2 4302 PIS 90847 Legrand 3 6469 PIS 90847 Legrand 1 1908 POS 90844 Merlin Gerin 3 C80A Merlin Gerin 2 B100A TBLO, POW TBLO, POW 90850, 90853 90850, 90853 Merlin Gerin 1 C60N POS 90844 Merlin Gerin 1 C32N POS 90844 Merlin Gerin 2 C60N POS 90844 Merlin Gerin 4 C60N POS 90844 Merlin Gerin 3 C32N POS 90844 Merlin Gerin 3 C45AD POS 90844 Proteus 1 C16 POS 90844 Proteus 1 C6 POS 90844 Proteus 3 C6 POS 90844 Siemens 17U 2 5SQ12 TBLO 90853 Siemens 17U 3 5SQ13 TBLO 90853 Siemens 17U 4 5SQ16 TBLO 90853 Siemens 17U 1 5SQ11 POW 90850 Siemens C10 1 5SX1 POW 90850 Siemens C32 2 5SX1-2 TBLO 90853 Siemens C70 3 5SX13 TBLO 90853 Siemens L20A 2 5SN2-2 TBLO 90853 Sursum 3 EA53 PIS 90847 Wylex 2 WRS40/2 POS 90844 484

Electrical s 3-In-1 Electrical Plug Accommodates high and low-voltage plugs up to 3 in diameter and 5-1/2 in length 2 sliding top lids can be used individually or together to accommodate small, medium and large-diameter cords up to 1-1/4 Constructed of yellow thermoplastic Visual label supplied in English/Spanish bilingual format Type PLO23 3-in-1 Plug Brady Electrical Plug s Plug lockouts prevent electrical plugs from being inserted into a wall outlet. Use when plug will not remain under the exclusive control of the person performing service or maintenance Constructed of rugged polypropylene Small 110V plug lockout: 2 H x 2 D x 3-1/2 W with 1/2 dia. hole for cable Large 220/500V plug lockout: 3-1/4 H x 3-1/4 D x 7 W with 1 dia. hole for cable Electrical/Pneumatic Plug Accommodates a large variety of electrical plugs up to 3-1/2 in diameter and 5 in length as well as male air hose connectors Holes accommodate electrical cord or necked down pneumatic male fittings commonly attached to compressed air hose Works on 110V, 220V & 550V plugs Constructed of durable polystyrene Type 65674 Small 110V Plugout 65675 Large 220/500V Plugout PLO27E Type Electrical/Pneumatic Plug Hubbell Plugout Two sizes available to fit most heavy industrial plug applications Small version accepts plugs with maximum 2-3/4 diameter and 4-3/4 length with 1 cord Large version accepts plugs with maximum 4-1/2 diameter and 10-3/20 length with 19/20 cord Type 65695 Small Plugout 65968 Large Plugout Stopower Plug s Ideal for office equipment and other frequently locked out cords For use on 2 or 3 pronged polarized plugs Cord cannot be plugged in with Stopower in place Device cannot be removed without key Type Qty. 65673 Red Stopower Plug (keyed different) 1 QB0033 Red Stopower Plug (keyed alike) 1 Wall Switch s Use with most wall-mounted switches Easy to install using existing screws 65392 & 65696 come in a high visibility red color and can lock switch in on or off position WSLO features a patented non-hinge design is made of strong, clear polycarbonate Qty. 65392 Red Wall Switch 1 65696 Red Wall Switch 6 WSLO Clear Wall Switch 1 *Padlock not included Electrical Kits Brady s Electrical Kits include an array of hasps, clamp-on breaker lockouts, tags mini cable lockouts and much more. View page 442 for a variety of Kits. ww.magtool.com 485

Electrical s & Tools Push Button and E-Stop Safety Covers Universal fit for IEC & NEMA buttons Removable, transparent red cover allows view of button position Hinged eyelet accepts safety locks Each base supplied with one yellow and one red label Fits Qty. 134018 Sm. base & short cover 16mm button 1 130819 Sm. base & tall cover 16mm button 1 130820 Med. base & cover 22mm button 1 130821 Lrg. base & cover 30mm button 1 Push Button and E-Stop Cover Bases One-time installation of low profile base Personnel can apply their portable safety cover to any installed base Fast and convenient lockout at the point of need Each base supplied with one yellow and one red label Fits Qty. 130822 Small bases 16mm button 5 130823 Medium bases 22mm button 5 130824 Large bases 30mm button 5 Universal Fuse Designed to prevent the un-intended re-energization of an energy source through a fuse. Easy to use device fits most fuse holders between 20 and 400 amps Dimensions: 1.38 H x 0.59 W x 2.36 D Qty. 873367 Universal Fuse - Red 1 Push Button Cover NEMA 30.5 mm (PBL6) Push Button Cover IEC 22.5mm (PBL8) Push Button Safety Covers 104602: Clear Lexan hinged cover completely covers button, and prevents access. White legend plate included 104603: Clear Lexan & metal hinged cover completely covers button preventing access Emergency Stop Cover NEMA 30.5mm (PBL2) Emergency Stop Cover IEC 22.5mm (PBL4) Emergency Stop Safety Covers Permanently install over push/pull or twist-release emergency stops Durable metal bar locks button in the depressed (off) position when lock shackle is inserted Fuse Device Unique locking mechanism prevents device from being accidentally removed from fuse block Available in two sizes for most commonly used fuses PBL6 PBL8 Type Push Button Safety Cover - NEMA 30.5 mm Push Button Safety Cover - IEC 22.5 mm PBL2 PBL4 Type Emergency Stop Cover - NEMA 30.5 mm Emergency Stop Cover - IEC 22.5 mm Qty. 65750 Fuse size 13 32 6 65751 Fuse size 9 16 6 Safe-T-Grip Fuse Pullers Provides maximum convenience when removing or replacing cartridge fuses Notched handles for non-slip grip Clearly marked amperage ranges Exceeds MIL specifications AC Sensor Selected by OSHA Electrical Technical Equipment Committee as the only instrument of its type for use by OSHA compliance officers to identify and cite electrical hazards of 50-1000 volts AC CAT IV rated and UL Listed Fuse Blockout Device Use small blockout device to fit fuses 1 4, 9 32, 13 32 & 9 16 in size Use large blockout to fit 13 16, 11 16 & blade type fuses 65279 5 long Fuse Puller for 9 32 1 2 dia. fuses 65280 7-1 2 long Fuse Puller for 0-100A, 250V & 600V Patent #5,103,165 65269 AC Sensor Qty. 65690 Small Fuse Blockout 6 65691 Large Fuse Blockout 6 486

Gas & Air s Pneumatic Quick- Disconnect Isolates pneumatic energy without the expense and inconvenience of installing in-line lockout valves Device is applied to the male fitting, isolating equipment from all compressed air sources Accommodates the majority of 1/4, 1/8, 1/2 male fittings Hole in center of device allows for permanent storage on an air hose and a loop on the side can be used to hang the hose and lockout device SMC Air Line Regulator Enables regulator to be locked in the on, off or throttled position Easy installation: remove snap cap, install lockout on regulator rod, snap replacement cap on regulator Comes with lockout, cap and allen wrench. Padlock not included 64539 for Miniature SMC Models AR2000 / NAR2000 64540 for Intermediate SMC Models AR3000 / NAR3000 Prinzing Cylinder Tank Used to lockout cylinder tanks, including propane tanks on fork trucks and stand alone propane tanks Apply with ease to prevent access to the valve handle Designed to fit in tight spaces Valve stem hole is 1.25 in diameter Made of rugged polystyrene plastic SD02M Description Cylinder Tank Accommodates padlock with up to 1/4 shackle Qty. 64221 Pneumatic 1 65645 Pneumatic 6 Want to learn more about? Download the 5 Steps to an Effective Program Whitepaper View Brady s full line of product solutions Prinzing Gas Cylinder Snap Cap Gas Cylinder Prevents access to the main cylinder valve Designed to fit most North American high and low pressure gas cylinders No need to match your lockout device to varying diameters and threads of cylinder caps Accommodates neck rings up to 3-1/2 diameter Easy and efficient installation saves you time LM023E Gas Cylinder Meets DOT standards Denies access to the main cylinder control and regulator attachment Powder coated welded steel construction is extremely durable Color 90496 6.5 x 3-1/8 x 11 UN, High Pressure Fine Thread Yellow 95137 6.5 x 3-1/2 x 11 UN, Low Pressure Fine Thread Yellow 95138 6.5 x 3-1/8 x 11 UN, High Pressure Coarse Thread Yellow 95139 6.5 x 3-1/2 x 11 UN, Low Pressure Coarse Thread Yellow 1-800-661-9983 487

Training & Awareness Aids OSHA Training Requirements: Those who will perform servicing or maintenance (authorized employees) must be trained to: - Recognize hazardous energy sources and understand the energy type and magnitude - Identify and properly operate the applicable energy-isolating devices - Safely apply and remove devices Those who operate the machinery or work in the area where LOTO is performed (affected employees) must be trained to: - Recognize when activities are in progress - Understand the purpose of the energy control program and the importance of not tampering with devices when encountered in the workplace Additional training is required when using tagout instead of lockout. See Section (C)(7)(ii) in the 1910.147 standard. Employers must document when training took place, who attended, and the topics covered. Employees must be retrained under the following situations: - Employee assigned to new job - Change made to energy control policies or procedures - Machinery installed or modified, presenting a new hazard - Whenever the employer has reason to believe that there are problems with the employee s understanding or use of the procedures Authorized employees must undergo an annual review to ensure they fully understand their responsibilities under the program Handbook 16-page training booklet with quiz instructs workers how to protect themselves from hazardous energy Qty. 66219 Handbook 10 63004 Spanish-language Handbook 10 Safety Training Booklet 16-page training booklet covers the basics of safety Qty. 2112-TEN Safety 10 2112 Safety 25 2112SP-TEN Safety - Spanish 10 2112SP Safety - Spanish 25 Wallet Safety Cards Wallet size card contains important reminders for lockout safety Qty. LOSC13 English Wallet Card 10 LOSC13 BI English/Spanish Wallet Card 10 Prinzing Safety Poster Training poster reinforces your energy control program 18 H x 24 W, laminated on both sides LOSP8 LOSP8SP Description Safety Poster Spanish-language version Hard Hat Labels 2 diameter hard hat labels made of self-sticking indoor/outdoor grade vinyl A convenient way to identify first aid personnel, authorized operators and visitors to your facility Qty. 42248 Trained 4 50193 Authorized 4 488

Training & Awareness Aids Safety Training Video: Global Best Practice Training Available on DVD or USB Comprehensive training video features targeted regulatory and compliance content 5 languages included: English, Spanish, French, Portuguese, and Simplified Chinese Includes Instructor s Guide, Employee Quiz and 25 min video that: Clearly defines and explains Overviews compliance standards and regulations from countries around the world Outlines an effective four-step program for employers Covers important subtopics in-depth such as handling group lockout and shift changeovers Bonus Feature: 19 short installation videos on how to use some of the most common lockout devices 132426 LOTO Global Training Video DVD 132427 LOTO Global Training Video USB LOTO Global Training Video USB - European 833918 Supplies information in English, French, Dutch, German, Portuguese, Italian, Spanish, Turkish, Polish and Russian : Your Key To Safety Train employees to protect themselves and others during machine servicing and maintenance. This program shows how to recognize all potential hazards and handle them safely. Includes: Live action 20 minute, DVD video 24 page Instructor guidebook 11 employee handbooks 1 - Trainer Tools CD-ROM 1 - Awareness Poster For Life Learn from other workers tragic mistakes. This motivational video presents six real-life dramatizations of actual lockout accidents and analyzes how they could have been prevented Suitable for new and experienced employees Run time: 19 minutes LOTO for Authorized & Affected Personnel Provides a comprehensive introduction to the key components of an effective LOTO program Comes with reproducible quiz and certificate Spanish language video also available (quiz and certificate in English only) Run time: 17 minutes (DVD format) Qty. Description Description 104275 Complete Kit - DVD version - English 1 104216 Complete Kit - DVD version - Spanish 1 66255 51793 For Life VHS video (includes 10 English booklets) For Life DVD English/Spanish video (includes 10 English booklets) 51454 51455 LOTO For Authorized & Affected Personnel DVD (English) LOTO For Authorized & Affected Personnel DVD (Spanish) 51544 For Life VHS Spanish video (includes 10 English booklets) 65555 Additional English booklets (10/pkg) 1-800-661-9983 489

Procedures BradyClientServices.com Procedures Written procedures are a critical piece of an effective lockout tagout program. They provide clear, visually-intuitive down, isolating, blocking and securing equipment to control hazardous energy. When employees can easily understand lockout procedures, they are more likely to utilize the procedures for safe machine lockout. Brady s software programs and procedure writing service provide you with options to complete these procedures. OSHA Regulations 29 CFR 1910.147 (c)(4) Machine-specific procedures are required for equipment having more than one energy source, as well as for much equipment having a single energy source. /Tagout Posted Procedure Clearly identifies the number of lockout points requiring attention for proper shutdown. ID#: Created: Revised: BRDY-001-430105 9/11/2013 9/13/2013 5 Points Purpose: Scope: Authorization: Enforcement: Note: Facility: Description: Site 1 - Refrigeration Refrigeration Compressor #4 Location: Engine Room This is an example of Link360's "Long Form". The long form allows you to freely define the actions of each step, add photos for each step, and add further detail that is required for complex lockout procedures. For simple lockout procedures, see the "Short Form". This procedure establishes the minimum requirements for the lockout of energy isolating devices whenever maintenance or servicing is done on machines or equipment. This procedure shall be used to ensure that the machine or equipment is stopped, isolated from all potentially hazardous energy sources and locked out before employees perform any servicing or maintenance where the unexpected energization or start-up of the machine or equipment or release of stored energy could cause injury. This procedure shall only be used by employees that have been trained as "Authorized" employees under OSHA 1910.147. Employees with the following job roles are authorized to use this procedure: <list job roles> Failure to properly follow lockout-tagout procedure may result in corrective action. Application Process 1. Notify affected personnel. 2. Properly shut down machine. 3. Isolate all energy sources. 4. Apply lockout devices, locks, & tags. 5. Verify total de-energization of all sources. Steps Facility and location are prominently stated to minimize any chance of confusion. Step # Action Info 1 E-1 Electrical 480V PROPER PPE REQUIRED: Arc flash shield, 8 cal/cm2, class E gloves, electrical rated hardhat. The E-1 Disconnect is located to the West of the machine. Turn Disconnect to the off position and lock out. Use a Lock and hasp device. E-1 Step by step written instructions detail the requirements for appropriate lockout. 2!-1 Note For the next step, you will need to obtain a universal lock and chain device from the /Tagout Station, located on the West wall of the Engine Room. Upon re-energization, return universal lock and chain device to the /Tagout Station. Incorporated images help convey the message to your entire workforce. Page 1 of 3 490

Procedures BradyClientServices.com LINK360 Software Brady s LINK360 cloud based software is the first software to give you a complete view of the activities associated with creating, reviewing and updating visual information while driving internal employee engagement and accountability. LINK360 includes three modules: lockout/tagout, confined space and reliability. The LINK360 /Tagout Application helps companies: Receive compliance assistance with OSHA 1910.147 for lockout of hazardous energy sources Manage lockout/tagout programs Create visually instructive safety procedures, tags and energy source labels for printing Gain 24-hour access with our free mobile app for ios, mobile phones and tablets Interested in a demo? Call 1-888-311-0774 or email ClientServices@bradycorp.com A Snapshot of LINK360 Software: Cloud-based software with free mobile apps Create and update procedures and permits Facilitate reviews, comments and approvals Setup regularly scheduled audit processes and reminders Time-stamping and record keeping Comprehensive procedure management tool Procedure Writing Service This turnkey service is the most effective, stress-free way to create an OSHA-compliant lockout/tagout program. You can trust our field engineers to take care of every detail, including: Evaluating your needs and equipment requirements Creating visually-instructive procedures specific to your machinery, facility and employee safety requirements Laminating and installing the new lockout/tagout procedures Installing color-coded energy source ID tags Collaborating with your team during the process, helping you understand how to successfully maintain the program in-house For more information, visit BradyClientServices.com or call 1-800-661-9983 491

Procedures Post procedures near the point of need so they are easy to find and readily accessible. OSHA Requirement Procedure Station Silk-screened backboard made from durable polystyrene Includes pre-drilled holes and hardware for wall mounting 3-ring, 1.5 binder made from 55 gauge polyethylene Station dimensions: 20 Hx14 Wx4.5 D LOSP22 Procedure Station With Binder & 25 Forms 99289 Procedure Station With Binder Only LOSB1 Procedure Binder Only LOSF5 Procedure Forms (25/pk) Clip Board Heavy duty, red clipboard allows lockout information and hardware to be conveniently carried directly to the lockout location Clipboard can also be hung in place using attached strap safety tips silk-screened onto the back Procedures, locks and hasps sold separately LOCB Clip Board 29 CFR 1910.147 (c)(4) Machine-specific procedures are required for equipment having more than one energy source, as well as for much equipment having a single energy source. OTHER WAYS OF PROVIDING ACCESS TO PROCEDURES Print procedures to adhesive or magnetic labels and adhere to directly to machine. Attach procedures to work orders manually or by linking the digital procedure file to work orders generated in a computer maintenance management system Provide access to procedures online, allowing workers to view and print procedures from their own computer Magnetic Backed Open-Ended Adhesive Backed Open-Ended Zip-lock Closure Open- Ended Protective Envelopes Transparent, durable vinyl construction Fluorescent Protective Envelopes Ideal for indoor or outdoor use Protects tags and cards on machinery, valves, switches, controls, and more Available with a variety of closure and mounting features Size Qty. 81769 Magnetic Backed 4.5 x 6.5 10 81770 Magnetic Backed 5.5 x 8.5 10 81771 Adhesive Backed 4.5 x 6.5 10 81772 Adhesive Backed 5.5 x 8.5 10 81765 Zip-lock w/o Grommet 4.5 x 6.5 10 81767 Zip-lock w/o Grommet 5.5 x 8.5 10 81766 Zip-lock w/ Grommet 4.5 x 6.5 10 81768 Zip-lock w/ Grommet 5.5 x 8.5 10 81763 Open-Ended 4.5 x 6.5 10 81764 Open-Ended 5.5 x 8.5 10 Clear envelopes with fluorescent edging, great for color-coding lockout procedures and other shop information Durable 8 gauge vinyl construction withstands harsh environments Ideal for indoor or outdoor use Size Color Qty. 56941 9 x 9 Fluorescent Green 25 56945 9 x 12 Fluorescent Green 25 56942 9 x 9 Fluorescent Orange 25 56946 9 x 12 Fluorescent Orange 25 56944 9 x 9 Fluorescent Yellow 25 56948 9 x 12 Fluorescent Yellow 25 Adhesive & Magnetic Backed Envelopes Made of non-glare clear vinyl material Size: 8-1/2 x 11 Color Qty. 50961 Adhesive Backed Envelopes 10 50962 Magnetic Backed Envelopes 10 492

Signs & Labels Energy Source ID Requirements OSHA 1910.333(e) and (f) require that all disconnecting means show the magnitude and shall be legibly marked to indicate the purpose, unless located and arranged so the purpose is evident. ANSI Z244.1-2003, Control of Hazardous Energy, states that all energy isolating devices should be adequately labeled or marked unless they are located so that their purpose is clearly evident. Identification shall include: Machine, equipment, process supplied Energy type and magnitude 86248 3-1/2" x 5" B-302 5/pk 86250 3-1/2" x 5" B-302 5/pk 86216 3-1/2" x 5" B-302 5/pk Safety Labels A variety of Labels made of durable, self-sticking polyester (B-302) are available to identify energy sources. More Labels on page 224. 86246 3-1/2" x 5" B-302 5/pk 86245 3-1/2" x 5" B-302 5/pk 86204 3-1/2" x 5" B-302 5/pk Over 200 Safety Signs Available! Brady carries a wide range of Signs to keep you and your employees safe around energy sources and equipment. Safety signs come in durable materials including plastic, aluminum and self-sticking vinyl. More Signs on page 118. PRINZING Floor Stand Made from rugged polyethylene, resists most chemicals Message printed on front and back Size SF647E Floor Stand 7 x 10 (side 1) Two-In-One Floor Stand (side 2) Lightweight corrugated polypropylene (B-836) is printed on inside and out - offering two stands for the price of one Size 92289 Two-In-One Floor Stand 20 x 12 Magnetic Signs Made of flexible magnetic vinyl Legend Size 66004 Breakers Locked Out 5 x 3-1/2 66005 Breakers Locked Out 7 x 5 66006 Do Not Operate 5 x 3-1/2 66007 Do Not Operate 7 x 5 66008 Equip Being Serviced 5 x 3-1/2 66009 Equip Being Serviced 7 x 5 493