KIT 5625 85562510200 b-24d LIBERATOR For most of WWII, Consolidated's B-24 Liberator was the largest bomber available to the U.S. Army Air Forces. Only when the B-29 Superfortress became operational late in the war did the B-24 give up this distinction. The B-24 operated in every theater of the war by the USAAF, and the British also used it in large numbers. Your Revell B-24D model features a detailed cockpit, interior and landing gear plus movable turrets and guns, optional bomb bay doors that can be open with a bomb load or closed and a highly detailed tow tractor with towbar. Authentic decal markings with nose art for two vertions are also included. * REPEAT SEVERAL TIMES * A REPETER PLUSIEURS FOIS * REPEAT PROCEDURE * OPTIONAL PARTS * DECAL * ASSEMBLY CAUTION * REPETEZ ` ` LE PROCEDE ` ` * PIECES EN OPTION * DECAL COMANIE *ATTENTION `D ASSEMBLEE ` * CEMENT TOGETHER * A COLLER * REMOVE AND THROW AWAY * A RETIRER ET JETER * DO NOT CEMENT * NE PAS COLLER READ THIS BEFORE YOU BEGIN * Study the assembly drawings. * Each plastic part is identified by a number. * In the assembly drawings, some parts will be marked by a star ( ) to indicate chrome plated plastic. * For better paint and decal adhesion, wash the plastic parts in a mild detergent solution. Rinse and let air dry. * Check the fit of each piece before cementing in place. * Use only cement for polystyrene plastic. * Scrape plating and paint from areas to be cemented. * Allow paint to dry thoroughly before handling parts. * Any unused parts may be discarded. DECAL APPLICATION INSTRUCTIONS LIRE CE QUI SUIT AVANT DE COMMENCER * Etudier les schémas de montage. * Chaque pièce en plastique est identifiée par un numéro. * Sur les schémas de montage, certaines pièces sont marquées d'une étoile ( ) pour indiquer qu'elles sont en plastique chromé. * Pour une meilleure prise de la peinture et des autocollants, laver les pièces en plastique avec une solution détergente peu concentrée. Les rincer et les laisser sécher à l'air. * Vérifier que chaque pièce s'ajuste bien avant de la coller en place. * N'utiliser que de la colle pour polystyrène. * Gratter les parties à coller pour enlever le chrome et la peinture. * Laisser la peinture bien sécher avant de manipuler les pièces. * Toute pièce inutilisée peut être jetée. DIRECTIVES D'APPLICATION DES AUTOCOLLANTS This paint guide is provided to complete this kit as shown on the box. Ce guide de peintures est fourni pour reproduire le modèle réduit qui apparaît sur la boîte. Semi Gloss Black Olive Drab Red Medium Green Aluminum Noir satiné Gris vert Rouge Vert moyen Aluminum 1. Cut desired decal from sheet. 2. Dip decal in water for a few seconds. 3. Place wet decal on paper towel. 4. Wait until decal is movable on paper backing. 5. Place decal in position on model, face up and slide backing away. 6. Press out air bubbles with a soft damp cloth. 7. Milkiness that may appear is for better decal adhesion and will dry clear. Wipe away any excess adhesive. 8. Do not touch decal until fully dry. 9. Allow the decals 48 hours to dry before applying clear coat. NOTE: Decals are compatible with setting solutions or solvents. 1. Découper l'autocollant désiré de la feuille. 2. Tremper l'autocollant dans de l'eau pendant quelques secondes. 3. Placer l'autocollant mouillé sur une serviette en papier. 4. Attendez que l'autocollant puisse être déplacé sur son support en papier. 5. Mettre l'autocollant en position sur le modèle face sur le dessus et faire glisser le support pour l'enlever. 6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air. 7. La substance laiteuse qui peut apparaître est destinée à améliorer l'adhésion de l'autocollant et devient incolore au séchage. Essuyer pour enlever tout excédent d'adhésif. 8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec. 9. Laisser l'autocollant sécher pendant 48 heures avant d'appliquer une couche transparente. REMARQUE: Les autocollants sont compatibles avec les solutions de fixage ou les solvants. Zinc Chromate Green Yellow Neutral Gray Wood Vert de zinc Vert Jaune Gris neutre Bois If you have any questions or comments, call our hotline at: (800) 833-3570 or, please write to: Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007 Be sure to include the plan number (85562510200), part number, description, your return address and phone number. Visit our website: www.revell.com Revell Inc Elk Grove Village, IL. Copyright 2010. All rights reserved.
1 cockpit ASSEMBLY 104 SEAT 104 BOMBARDIER'S SEAT CROMATE WITH SEAT MILITARY BROWN 52 INSTRUMENT PANEL WITH FLAT WHITE DETAIL 41 CONTROL YOKE 50 SIGHT BOMBARDIER IN POSITION SEE PAGE 9 FOR ASSEMBLY FLAT WHITE : STRAPS, BOTH FLESH : HANDS AND FACE, BOTH BROWN : GOGGLES WITH LENS, BOTH TAN (COLLARS) 50 BOMB SIGHT 53 SEAT 41 CONTROL YOKE CONSOLE ( WITH FLAT WHITE DETAIL) 19 FLOOR 114 113 PILOT CO-PILOT 2 BROWN 54 SEAT SUPPORT left bomb bay ASSEMBLY 75 9 WAIST INSIDE 21L WAIST AMMUNITION BOX NATURAL WOOD 75 1L FUSELAGE HALF 37 & 38 BOMB RACK SUPPORTS 9 OR 20 1000 LB. BOMB 60R 38 AFT RACK SUPPORT 60L PAINT NOTE: INSIDE FUSELAGE 35 BOMB RACK 36 BOMB BAY SUPPORT 37 FORWARD RACK SUPPORT 35 BOMB RACK 61B 61T 500 LB. BOMB Kit 5625 - Page 2
3 right bomb bay assembly 37 & 38 BOMB RACK SUPPORTS 1R FUSELAGE HALF 8 ANTENNA HOUSING 75 S 9 WAIST INSIDE ONLY PAINT NOTE: INSIDE FUSELAGE 21R 12 OR 23 WAIST AMMUNITION BOX NATURAL WOOD 38 AFT RACK SUPPORT 20 AFT BULKHEAD 61T 35 BOMB RACK 61B 37 FORWRD RACK SUPPORT 36 BOMB BAY SUPPORT 35 BOMB RACK 4 500 LB. BOMB * 11 GUN YOKE 46 WAIST GUN * 11 GUN YOKE 10L GUN MOUNT waist gun assembly 46 WAIST GUN * 7 REAR ANTENNA SILVER GUNNERS IN POSITION SEE PAGE 9 FOR ASSEMBLY 60R 1000 LB. BOMB 60L 10R GUN MOUNT 22 WAIST GUN PLATFORM Kit 5625 - Page 3
5 FORWARD FUSELAGE ASSEMBLY 75 83 83 75 106 NOSE FRAME IS FUSELAGE COLOR 6 4R NOSE WHEEL INSIDE ONLY 4L NOSE WHEEL INSIDE ONLY 108 BOMBARDIER'S PANEL SEMI GLOSS BLACK WITH KNOBS AND ALUMINUM SWITCHES nose gear / fuselage ASSEMBLY 55L NOSE WHEEL HALF SEMI GLOSS BLACK 24 NOSE GEAR SUPPORT 57 RETAINER 55R NOSE WHEEL HALF SEMI GLOSS BLACK NEUTRAL 25 FENDER BOTTOM NEUTRAL 23 NOSE GEAR 56 NOSE GEAR BULKHEAD INSIDE ONLY 1R FUSELAGE 32 FORWARD BULKHEAD COMPLETED COCKPIT 1L FUSELAGE Kit 5625 - Page 4
7 wing ASSEMBLY 31 ENGINE FRONT 49 PROPELLER SHAFTS PAINT NOTE FOR ENGINES: CYLINDERS - STEEL RODS - OR BLACK 49 PROPELLER SHAFTS 31 ENGINE FRONT 31 ENGINE FRONT 31 ENGINE FRONT 14R WING BOTTOM 14L WING BOTTOM 13R WING TOP 59 FUEL VENT 59 FUEL VENT 13L WING TOP 48 PROPELLERS 12 COWL RINGS PAINT NOTE FOR PROPELLERS: SEMI GLOSS BLACK WITH ALUMINUM HUB AND YELLOW TIPS 12 COWL RINGS 48 PROPELLERS WING TO FUSELAGE WING TO FUSELAGE Kit 5625 - Page 5
8 strut to wing ASSEMBLY MAIN LANDING GEAR 26L MAIN WHEEL 58R MAIN GEAR TIRE INNER HALF MAIN LANDING GEAR 26R MAIN WHEEL 28L BRACE 28R BRACE 27L 27R 58L MAIN GEAR TIRE OUTER HALF NEUTRAL PAINT NOTE: ASSEMBLIES AND WHEEL WELLS ARE PAINTED FUSELAGE COLOR 9 tail gun ASSEMBLY 75 81 TAIL TURRET REAR 81 TAIL TURRET FRONT 47 TAIL GUNS GUNMETAL 10 STABILIZER ASSEMBLY 15T HORIZONTAL STABILIZER TOP 15B HORIZONTAL STABILIZER BOTTOM Kit 5625 - Page 6
10 STABILIZER assembly CONTINUED 16R VERTICAL STABILIZER INNER COMPLETED HORIZONTAL STABILIZER 16L VERTICAL STABILIZER INNER 11 16R VERTICAL STABILIZER OUTER END VIEW AFT END OF FUSELAGE 16L VERTICAL STABILIZER OUTER front fuselage assembly PAINT NOTE: FRAMES ON S, CANOPY AND TURRET IS FUSELAGE COLOR 77 CANOPY 78L COCKPIT 79 TURRET DOME 78R COCKPIT 42 GUN RING 44 GUNS GUNMETAL 74 ASTRODOME 5 PITOT PROBE 43 RETAINER RING 5 PITOT PROBE ANGLE FOR PITOT PROBES Kit 5625 - Page 7
12 bomb bay door ASSEMBLY CLOSED 34B FORWARD 34C AFT OPEN 33D FORWARD 33A AFT 102 BELLY PANEL 34D AFT 34A FORWARD FORWARD FORWARD 13 DEATAILS OMITTED FOR CLARITY 33C FORWARD 33B AFT front nose / final ASSEMBLY A B 103 NOSE GUN GUNMETAL C 103 NOSE GUN GUNMETAL 105 NOSE (FRAME IS FUSELAGE COLOR) UNDERSIDE OF AFT FUSELAGE 103 NOSE GUNS GUNMETAL 39 TAIL SKID FUSELAGE COLOR ALUMINUM 3 REAR BOARDING NEUTRAL ZINC CROMATE 6 BOARDING LADDER Kit 5625 - Page 8
14 tractor assembly 69L TRACKS STEEL WITH FLAT BLACK RUBBER SHOES 70 TRACTOR BOTTOM 66R HOOD HALF 63 GRILLE 66L HOOD HALF 62 FENDERS 69R TRACKS STEEL WITH FLAT BLACK RUBBER SHOES 64 LIGHT SHADED AREA SILVER 64 LIGHT SHADED AREA SILVER 72 SEAT WITH OLIVE CUSHIONS 65 WINDSHIELD 67 COMPRESSOR WITH FLAT BLACK CYLINDERS 15 68 GUARD 71 TOW BAR figure assembly FLIGHT CREW Uniforms - kahki, Jackets - dark brown, Llife Vests - yellow, Straps - dirty white, light gray, or tan, Buckles - silver, Caps - brown, Boots - brown leather with an off-white fleece lining at the top. 117 ARM 115 TORSO 118 LEGS 116 ARM (HOSE) FLAT WHITE (STRAPS) 122 ARM 120 BACK BROWN (GLOVES,BOOTS,GOGGLES WITH LENS) SERVICE MECHANICS Coveralls - Olive drab, gray, or khaki, Jackets - Olive green, Caps - olive drab, Boots - brown leather. Wrench - silver or dark gray (HOSE) FLAT WHITE (STRAPS) 119 FRONT 121 ARM 124 BACK 125 ARM BROWN (GLOVES,BOOTS,GOGGLES WITH LENS) BOMBARDIER STANDING WAIST GUNNER SQUATING WAIST GUNNER 126 ARM (HOSE) FLAT WHITE (STRAPS) 123 FRONT Kit 5625 - Page 9
16 decal placement Kit 5625 - Page 10
17 decal placement Kit 5625 - Page 11
18 decal placement Kit 5625 - Page 12